mpc8306 powerquicc ii pro integrated communications processor family hardware...
TRANSCRIPT
Freescale SemiconductorTechnical Data
© 2011 Freescale Semiconductor, Inc. All rights reserved.
This document provides an overview of the MPC8306 PowerQUICC II Pro processor features. The MPC8306 is a cost-effective, highly integrated communications processor that addresses the requirements of several networking applications, including residential gateways, modem/routers, industrial control, and test and measurement applications. The MPC8306 extends current PowerQUICC offerings, adding higher CPU performance, additional functionality, and faster interfaces, while addressing the requirements related to time-to-market, price, power consumption, and board real estate. This document describes the electrical characteristics of MPC8306.
To locate published errata or updates for this document, refer to the MPC8306 product summary page on our website listed on the back cover of this document or contact your local Freescale sales office.
Document Number:MPC8306ECRev. 2, 09/2011
Contents1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 73. Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 104. Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 115. RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 126. DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137. Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188. Ethernet and MII Management . . . . . . . . . . . . . . . . . 219. TDM/SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10. HDLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3011. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3212. DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3413. eSDHC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3514. FlexCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3715. I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3816. Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4017. GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4118. IPIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4219. SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4220. JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4421. Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 4822. Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5823. Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6524. System Design Information . . . . . . . . . . . . . . . . . . . 6825. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . 7126. Document Revision History . . . . . . . . . . . . . . . . . . . 73
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
2 Freescale Semiconductor
Overview
1 OverviewThe MPC8306 incorporates the e300c3 (MPC603e-based) core built on Power Architecture® technology, which includes 16 Kbytes of each L1 instruction and data caches, dual integer units, and on-chip memory management units (MMUs). The MPC8306 also includes two DMA engines and a 16-bit DDR2 memory controller.
A new communications complex based on QUICC Engine technology forms the heart of the networking capability of the MPC8306. The QUICC Engine block contains several peripheral controllers and a 32-bit RISC controller. Protocol support is provided by the main workhorses of the device—the unified communication controllers (UCCs). A block diagram of the MPC8306 is shown in the following figure.
Figure 1. MPC8306 Block Diagram
Each of the five UCCs can support a variety of communication protocols such as 10/100 Mbps MII/RMII Ethernet, IEEE-1588, HDLC and TDM.
1 RMII/MII2x TDM Ports
16-KBD-Cache
16-KBI-Cache
e300c3 Core with Power2x DUART
Interrupt
I2CTimers
GPIO
DDR2
ControllerController
Baud RateGenerators
Accelerators
Single 32-bit RISC CP Serial DMA
Serial Interface
QUICC Engine Block
UC
C7
UC
C5
UC
C3
UC
C2
UC
C1
Time Slot Assigner
16 KB Multi-User RAM
FPU
Management
SPIRTC
Bus Controller
2x HDLC
2 RMII/MII
2x IEEE 1588
USB 2.0 HSHost/Device/OTG
ULPI
DMA 4 FlexCAN eSDHC
48 KB Instruction RAM
Engine
Enhanced Local
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 3
Overview
In summary, the MPC8306 provides users with a highly integrated, fully programmable communications processor. This helps to ensure that a low-cost system solution can be quickly developed and offers flexibility to accommodate new standards and evolving system requirements.
1.1 Features
The major features of the device are as follows:
• e300c3 Power Architecture processor core
— Enhanced version of the MPC603e core
— High-performance, superscalar processor core with a four-stage pipeline and low interrupt latency times
— Floating-point, dual integer units, load/store, system register, and branch processing units
— 16-Kbyte instruction cache and 16-Kbyte data cache with lockable capabilities
— Dynamic power management
— Enhanced hardware program debug features
— Software-compatible with Freescale processor families implementing Power Architecture technology
— Separate PLL that is clocked by the system bus clock
— Performance monitor
• QUICC Engine block
— 32-bit RISC controller for flexible support of the communications peripherals with the following features:
– One clock per instruction
– Separate PLL for operating frequency that is independent of system’s bus and e300 core frequency for power and performance optimization
– 32-bit instruction object code
– Executes code from internal IRAM
– 32-bit arithmetic logic unit (ALU) data path
– Modular architecture allowing for easy functional enhancements
– Slave bus for CPU access of registers and multiuser RAM space
– 48 Kbytes of instruction RAM
– 16 Kbytes of multiuser data RAM
– Serial DMA channel for receive and transmit on all serial channels
— Five unified communication controllers (UCCs) supporting the following protocols and interfaces:
– 10/100 Mbps Ethernet/IEEE Std. 802.3® through MII and RMII interfaces.
– IEEE Std. 1588™ support
– HDLC/Transparent (bit rate up to QUICC Engine operating frequency / 8)
– HDLC Bus (bit rate up to 10 Mbps)
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
4 Freescale Semiconductor
Overview
– Asynchronous HDLC (bit rate up to 2 Mbps)
– Two TDM interfaces supporting up to 128 QUICC multichannel controller channels, each running at 64 kbps
For more information on QUICC Engine sub-modules, see QUICC Engine Block Reference Manual with Protocol Interworking.
• DDR SDRAM memory controller
— Programmable timing supporting DDR2 SDRAM
— Integrated SDRAM clock generation
— 16-bit data interface, up to 266-MHz data rate
— 14 address lines
— The following SDRAM configurations are supported:
– Up to two physical banks (chip selects), 256-Mbyte per chip select for 16 bit data interface.
– 64-Mbit to 2-Gbit devices with x8/x16 data ports (no direct x4 support)
– One 16-bit device or two 8-bit devices on a 16-bit bus,
— Support for up to 16 simultaneous open pages for DDR2
— One clock pair to support up to 4 DRAM devices
— Supports auto refresh
— On-the-fly power management using CKE
• Enhanced local bus controller (eLBC)
— Multiplexed 26-bit address and 8-/16-bit data operating at up to 66 MHz
— Eight chip selects supporting eight external slaves
– Four chip selects dedicated
– Four chip selects offered as multiplexed option
— Supports boot from parallel NOR Flash and parallel NAND Flash
— Supports programmable clock ratio dividers
— Up to eight-beat burst transfers
— 16- and 8-bit ports, separate LWE for each 8 bit
— Three protocol engines available on a per chip select basis:
– General-purpose chip select machine (GPCM)
– Three user programmable machines (UPMs)
– NAND Flash control machine (FCM)
— Variable memory block sizes for FCM, GPCM, and UPM mode
— Default boot ROM chip select with configurable bus width (8 or 16)
— Provides two Write Enable signals to allow single byte write access to external 16-bit eLBC slave devices
• Integrated programmable interrupt controller (IPIC)
— Functional and programming compatibility with the MPC8260 interrupt controller
— Support for external and internal discrete interrupt sources
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 5
Overview
— Programmable highest priority request
— Six groups of interrupts with programmable priority
— External and internal interrupts directed to host processor
— Unique vector number for each interrupt source
• Enhanced secure digital host controller (eSDHC)
— Compatible with the SD Host Controller Standard Specification Version 2.0 with test event register support
— Compatible with the MMC System Specification Version 4.2
— Compatible with the SD Memory Card Specification Version 2.0 and supports the high capacity SD memory card
— Compatible with the SD Input/Output (SDIO) Card Specification, Version 2.0
— Designed to work with SD Memory, miniSD Memory, SDIO, miniSDIO, SD Combo, MMC, MMCplus, and RS-MMC cards
— Card bus clock frequency up to 33.33 MHz.
— Supports 1-/4-bit SD and SDIO modes, 1-/4-bit modes
– Up to 133 Mbps data transfer for SD/SDIO/MMC cards using 4 parallel data lines
— Supports block sizes of 1 ~ 4096 bytes
• Universal serial bus (USB) dual-role controller
— Designed to comply with Universal Serial Bus Revision 2.0 Specification
— Supports operation as a stand-alone USB host controller
— Supports operation as a stand-alone USB device
— Supports high-speed (480-Mbps), full-speed (12-Mbps), and low-speed (1.5-Mbps) operations. Low speed is only supported in host mode.
• FlexCAN module
— Full implementation of the CAN protocol specification version 2.0B
— Up to 64 flexible message buffers of zero to eight bytes data length
— Powerful Rx FIFO ID filtering, capable of matching incoming IDs
— Selectable backwards compatibility with previous FlexCAN module version
— Programmable loop-back mode supporting self-test operation
— Global network time, synchronized by a specific message
— Independent of the transmission medium (an external transceiver is required)
— Short latency time due to an arbitration scheme for high-priority messages
• Dual I2C interfaces
— Two-wire interface
— Multiple-master support
— Master or slave I2C mode support
— On-chip digital filtering rejects spikes on the bus
— I2C1 can be used as the boot sequencer
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
6 Freescale Semiconductor
Overview
• DMA Engine
— Support for the DMA engine with the following features:
– Sixteen DMA channels
– All data movement via dual-address transfers: read from source, write to destination
– Transfer control descriptor (TCD) organized to support two-deep, nested transfer operations
– Channel activation via one of two methods (for both the methods, one activation per execution of the minor loop is required):
– Explicit software initiation
– Initiation via a channel-to-channel linking mechanism for continuous transfers (independent channel linking at end of minor loop and/or major loop)
– Support for fixed-priority and round-robin channel arbitration
– Channel completion reported via optional interrupt requests
— Support for scatter/gather DMA processing
• DUART
— Two 2-wire interfaces (RxD, TxD)
– The same can be configured as one 4-wire interface (RxD, TxD, RTS, CTS)
— Programming model compatible with the original 16450 UART and the PC16550D
• Serial peripheral interface (SPI)
— Master or slave support
• Power managemnt controller (PMC)
— Supports core doze/nap/sleep/ power management
— Exits low power state and returns to full-on mode when
– The core internal time base unit invokes a request to exit low power state
– The power management controller detects that the system is not idle and there are outstanding transactions on the internal bus or an external interrupt.
• Parallel I/O
— General-purpose I/O (GPIO)– 56 parallel I/O pins multiplexed on various chip interfaces – Interrupt capability
• System timers
— Periodic interrupt timer— Software watchdog timer— Eight general-purpose timers
• Real time clock (RTC) module
— Maintains a one-second count, unique over a period of thousands of years— Two possible clock sources:
– External RTC clock (RTC_PIT_CLK)– CSB bus clock
• IEEE Std. 1149.1™ compliant JTAG boundary scan
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 7
Electrical Characteristics
2 Electrical CharacteristicsThis section provides the AC and DC electrical specifications and thermal characteristics for the MPC8306. The MPC8306 is currently targeted to these specifications. Some of these specifications are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer design specifications.
2.1 Overall DC Electrical Characteristics
This section covers the ratings, conditions, and other characteristics.
2.1.1 Absolute Maximum Ratings
The following table provides the absolute maximum ratings.
Table 1. Absolute Maximum Ratings1
Characteristic Symbol Max Value Unit Notes
Core supply voltage VDD –0.3 to 1.26 V —
PLL supply voltage AVDD1AVDD2AVDD3
–0.3 to 1.26 V —
DDR2 DRAM I/O voltage GVDD –0.3 to 1.98 V —
Local bus, DUART, system control and power management, I2C, SPI, MII, RMII, MII management, eSDHC, FlexCAN, USB and JTAG I/O voltage
OVDD –0.3 to 3.6 V 2
Input voltage DDR2 DRAM signals MVIN –0.3 to (GVDD + 0.3) V 3
DDR2 DRAM reference MVREF –0.3 to (GVDD + 0.3) V 3
Local bus, DUART, SYS_CLK_IN, system control and power management, I2C, SPI, and JTAG signals
OVIN –0.3 to (OVDD + 0.3) V 4
Storage temperature range TSTG –55 to 150 C —
Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device.
2. OVDD here refers to NVDDA, NVDDB, NVDDC, NVDDF, NVDDG, and NVDDH from the ball map.3. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 100 ms during
power-on reset and power-down sequences.4. Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit may be exceeded for a maximum of 100 ms during
power-on reset and power-down sequences.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
8 Freescale Semiconductor
Electrical Characteristics
2.1.2 Power Supply Voltage Specification
The following table provides the recommended operating conditions for the MPC8306. Note that these values are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed.
The following figure shows the undershoot and overshoot voltages at the interfaces of the MPC8306
Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD
Table 2. Recommended Operating Conditions
Characteristic SymbolRecommended
ValueUnit Note
Core supply voltage VDD 1.0 V ± 50 mV V 1
PLL supply voltage AVDD1AVDD2AVDD3
1.0 V ± 50 mV V 1
DDR2 DRAM I/O voltage GVDD 1.8 V ± 100 mV V 1
Local bus, DUART, system control and power management, I2C, SPI, MII, RMII, MII management, eSDHC, FlexCAN, USB and JTAG I/O voltage
OVDD 3.3 V ± 300 mV V 1, 3
Junction temperature TA/TJ 0 to 105 C 2
Notes: 1. GVDD, OVDD, AVDD, and VDD must track each other and must vary in the same direction—either in the positive or negative
direction.2. Minimum temperature is specified with TA(Ambient Temperature); maximum temperature is specified with TJ(Junction
Temperature).3. OVDD here refers to NVDDA, NVDDB, NVDDC, NVDDF, NVDDG, and NVDDH from the ball map.
GNDGND – 0.3 V
GND – 0.7 VNot to Exceed 10%
G/OVDD + 20%
G/OVDD
G/OVDD + 5%
of tinterface1
1. tinterface refers to the clock period associated with the bus clock interface.
VIH
VIL
Note:
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 9
Electrical Characteristics
2.1.3 Output Driver Characteristics
The following table provides information on the characteristics of the output driver strengths.
2.1.4 Input Capacitance Specification
The following table describes the input capacitance for the SYS_CLK_IN pin in the MPC8306.
2.2 Power Sequencing
The device does not require the core supply voltage (VDD) and I/O supply voltages (GVDD and OVDD) to be applied in any particular order. Note that during power ramp-up, before the power supplies are stable and if the I/O voltages are supplied before the core voltage, there might be a period of time that all input and output pins are actively driven and cause contention and excessive current. In order to avoid actively driving the I/O pins and to eliminate excessive current draw, apply the core voltage (VDD) before the I/O voltage (GVDD and OVDD) and assert PORESET before the power supplies fully ramp up. In the case where the core voltage is applied first, the core voltage supply must rise to 90% of its nominal value before the I/O supplies reach 0.7 V; see Figure 3. Once both the power supplies (I/O voltage and core voltage) are stable, wait for a minimum of 32 clock cycles before negating PORESET.
NOTE
There is no specific power down sequence requirement for the device. I/O voltage supplies (GVDD and OVDD) do not have any ordering requirements with respect to one another.
Table 3. Output Drive Capability
Driver TypeOutput Impedance
()Supply Voltage (V)
Local bus interface utilities signals 42 OVDD = 3.3
DDR2 signal 18 GVDD = 1.8
DUART, system control, I2C, SPI, JTAG 42 OVDD = 3.3
GPIO signals 42 OVDD = 3.3
Table 4. Input Capacitance Specification
Parameter/Condition Symbol Min Max Unit Note
Input capacitance for all pins except SYS_CLK_IN and QE_CLK_IN
CI 6 8 pF —
Input capacitance for SYS_CLK_IN and QE_CLK_IN CICLK_IN 10 — pF 1
Note:1. The external clock generator should be able to drive 10 pF.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
10 Freescale Semiconductor
Power Characteristics
Figure 3. MPC8306 Power-Up Sequencing Example
3 Power CharacteristicsThe typical power dissipation for this family of MPC8306 devices is shown in the following table.
Table 5. MPC8306 Power Dissipation
CoreFrequency (MHz)
QUICC Engine Frequency (MHz)
CSBFrequency (MHz)
Typical Maximum Unit Note
133 133 133 0.272 0.618 W 1, 2, 3
200 233 133 0.291 0.631 W 1, 2, 3
266 233 133 0.451 0.925 W 1, 2, 3
333 233 133 0.471 0.950 W 1, 2, 3
Notes:1. The values do not include I/O supply power (OVDD and GVDD), but it does include VDD and AVDD power. For I/O power
values, see Table 6.2. Typical power is based on a nominal voltage of VDD = 1.0 V, ambient temperature, and the core running a Dhrystone
benchmark application. The measurements were taken on the evaluation board using WC process silicon.3. Maximum power is based on a voltage of VDD = 1.05 V, WC process, a junction TJ = 105C, and a smoke test code.
t
90%
V
Core Voltage (VDD)
I/O Voltage (GVDD and OVDD)
0
0.7 V
PORESET
>= 32 tSYS_CLK_IN
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 11
Clock Input Timing
The following table shows the estimated typical I/O power dissipation for the device.
4 Clock Input TimingThis section provides the clock input DC and AC electrical characteristics for the MPC8306.
NOTE
The rise/fall time on QUICC Engine input pins should not exceed 5 ns. This should be enforced especially on clock signals. Rise time refers to signal transitions from 10% to 90% of OVDD; fall time refers to transitions from 90% to 10% of OVDD.
4.1 DC Electrical Characteristics
The following table provides the clock input (SYS_CLK_IN) DC specifications for the MPC8306. These specifications are also applicable for QE_CLK_IN.
Table 6. Typical I/O Power Dissipation
Interface ParameterGVDD (1.8 V)
OVDD (3.3 V)
Unit Comments
DDR I/O65% utilization1.8 VRs = 20 Rt = 50 1 pair of clocks
266 MHz, 1 16 bits 0.141 — W —
Local bus I/O load = 25 pF1 pair of clocks
66 MHz, 26 bits
— 0.150 W 1QUICC Engine block and other I/Os TDM serial, HDLC/TRAN serial, DUART, MII, RMII, Ethernet management, USB, SPI, Timer output, FlexCAN, eSDHC
Note: 1. Typical I/O power is based on a nominal voltage of VDD = 3.3V, ambient temperature, and the core running a Dhrystone
benchmark application. The measurements were taken on the evaluation board using WC process silicon.
Table 7. SYS_CLK_IN DC Electrical Characteristics
Parameter Condition Symbol Min Max Unit
Input high voltage — VIH 2.4 OVDD + 0.3 V
Input low voltage — VIL –0.3 0.4 V
SYS_CLK_IN input current 0 V VIN OVDD IIN — ±5 A
SYS_CLK_IN input current 0 V VIN 0.5 V orOVDD – 0.5 V VIN OVDD
IIN — ±5 A
SYS_CLK_IN input current 0.5 V VIN OVDD – 0.5 V IIN — ±50 A
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
12 Freescale Semiconductor
RESET Initialization
4.2 AC Electrical Characteristics
The primary clock source for the MPC8306 is SYS_CLK_IN. The following table provides the clock input (SYS_CLK_IN) AC timing specifications for the MPC8306. These specifications are also applicable for QE_CLK_IN.
5 RESET InitializationThis section describes the AC electrical specifications for the reset initialization timing requirements of the MPC8306. The following table provides the reset initialization AC timing specifications for the reset component(s).
Table 8. SYS_CLK_IN AC Timing Specifications
Parameter/Condition Symbol Min Typical Max Unit Note
SYS_CLK_IN frequency fSYS_CLK_IN 24 — 66.67 MHz 1
SYS_CLK_IN cycle time tSYS_CLK_IN 15 — 41.6 ns —
SYS_CLK_IN rise and fall time tKH, tKL 1.1 — 2.8 ns 2
SYS_CLK_IN duty cycle tKHK/tSYS_CLK_
IN
40 — 60 % 3
SYS_CLK_IN jitter — — — ±150 ps 4, 5
Notes:1. Caution: The system, core and QUICC Engine block must not exceed their respective maximum or minimum operating
frequencies. 2. Rise and fall times for SYS_CLK_IN are measured at 0.33 and 2.97 V.3. Timing is guaranteed by design and characterization.4. This represents the total input jitter—short term and long term—and is guaranteed by design.5. The SYS_CLK_IN driver’s closed loop jitter bandwidth should be < 500 kHz at –20 dB. The bandwidth must be set low to
allow cascade-connected PLL-based devices to track SYS_CLK_IN drivers with the specified jitter.6. Spread spectrum is allowed up to 1% down-spread @ 33kHz (max rate).
Table 9. RESET Initialization Timing Specifications
Parameter/Condition Min Max Unit Note
Required assertion time of HRESET to activate reset flow 32 — tSYS_CLK_IN 1
Required assertion time of PORESET with stable clock applied to SYS_CLK_IN
32 — tSYS_CLK_IN 1
HRESET assertion (output) 512 — tSYS_CLK_IN 1
Input setup time for POR configuration signals (CFG_RESET_SOURCE[0:3]) with respect to negation of PORESET
4 — tSYS_CLK_IN 1, 2
Input hold time for POR config signals with respect to negation of HRESET
0 — ns 1, 2
Notes:1. tSYS_CLK_IN is the clock period of the input clock applied to SYS_CLK_IN. For more details, see the MPC8306 PowerQUICC
II Pro Integrated Communications Processor Family Reference Manual.2. POR configuration signals consist of CFG_RESET_SOURCE[0:3].
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 13
DDR2 SDRAM
The following table provides the PLL lock times.
5.1 Reset Signals DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 reset signals mentioned in Table 9.
6 DDR2 SDRAMThis section describes the DC and AC electrical specifications for the DDR2 SDRAM interface of the MPC8306. Note that DDR2 SDRAM is GVDD(typ) = 1.8 V.
6.1 DDR2 SDRAM DC Electrical Characteristics
The following table provides the recommended operating conditions for the DDR2 SDRAM component(s) of the MPC8306 when GVDD(typ) = 1.8 V.
Table 10. PLL Lock Times
Parameter/Condition Min Max Unit Note
PLL lock times — 100 s —
Table 11. Reset Signals DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit Note
Output high voltage VOH IOH = –6.0 mA 2.4 — V 1
Output low voltage VOL IOL = 6.0 mA — 0.5 V 1
Output low voltage VOL IOL = 3.2 mA — 0.4 V 1
Input high voltage VIH — 2.0 OVDD + 0.3 V 1
Input low voltage VIL — –0.3 0.8 V —
Input current IIN 0 V VIN OVDD — ±5 A —
Note: 1. This specification applies when operating from 3.3 V supply.
Table 12. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V
Parameter/Condition Symbol Min Max Unit Note
I/O supply voltage GVDD 1.7 1.9 V 1
I/O reference voltage MVREF 0.49 GVDD 0.51 GVDD V 2
I/O termination voltage VTT MVREF – 0.04 MVREF + 0.04 V 3
Input high voltage VIH MVREF+ 0.125 GVDD + 0.3 V —
Input low voltage VIL –0.3 MVREF – 0.125 V —
Output leakage current IOZ –9.9 9.9 A 4
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
14 Freescale Semiconductor
DDR2 SDRAM
The following table provides the DDR2 capacitance when GVDD(typ) = 1.8 V.
6.2 DDR2 SDRAM AC Electrical Characteristics
This section provides the AC electrical characteristics for the DDR2 SDRAM interface.
6.2.1 DDR2 SDRAM Input AC Timing Specifications
This table provides the input AC timing specifications for the DDR2 SDRAM (GVDD(typ) = 1.8 V).
The following table provides the input AC timing specifications for the DDR2 SDRAM interface.
Output high current (VOUT = 1.35 V) IOH –13.4 — mA —
Output low current (VOUT = 0.280 V) IOL 13.4 — mA —
Notes:1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.2. MVREF is expected to be equal to 0.5 GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREF may not exceed ±2% of the DC value.3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be
equal to MVREF. This rail should track variations in the DC level of MVREF.4. Output leakage is measured with all outputs disabled, 0 V VOUT GVDD.
Table 13. DDR2 SDRAM Capacitance for GVDD(typ) = 1.8 V
Parameter/Condition Symbol Min Max Unit Note
Input/output capacitance: DQ, DQS CIO 6 8 pF 1
Delta input/output capacitance: DQ, DQS CDIO — 0.5 pF 1
Note:1. This parameter is sampled. GVDD = 1.8 V ± 0.100 V, f = 1 MHz, TA = 25 °C, VOUT = GVDD 2,
VOUT (peak-to-peak) = 0.2 V.
Table 14. DDR2 SDRAM Input AC Timing Specifications for 1.8-V InterfaceAt recommended operating conditions with GVDD of 1.8 V± 100mV.
Parameter Symbol Min Max Unit Note
AC input low voltage VIL — MVREF – 0.25 V —
AC input high voltage VIH MVREF + 0.25 — V —
Table 15. DDR2 SDRAM Input AC Timing SpecificationsAt recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter Symbol Min Max Unit Note
Controller skew for MDQS—MDQ/MDM tCISKEW ps 1, 2
Table 12. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V (continued)
Parameter/Condition Symbol Min Max Unit Note
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 15
DDR2 SDRAM
The following figure shows the input timing diagram for the DDR controller.
Figure 4. DDR Input Timing Diagram
6.2.2 DDR2 SDRAM Output AC Timing Specifications
The following table provides the output AC timing specifications for the DDR2 SDRAM interfaces.
266 MHz –750 750
Notes:1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that
is captured with MDQS[n]. This should be subtracted from the total timing budget.2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW. This can be
determined by the equation: tDISKEW = ±(T/4 – abs(tCISKEW)) where T is the clock period and abs(tCISKEW) is the absolute value of tCISKEW.
Table 16. DDR2 SDRAM Output AC Timing SpecificationsAt recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter Symbol1 Min Max Unit Note
MCK cycle time, (MCK/MCK crossing) tMCK 5.988 8 ns 2
ADDR/CMD output setup with respect to MCK tDDKHAS ns 3
266 MHz 2.5 —
ADDR/CMD output hold with respect to MCK tDDKHAX ns 3
266 MHz 2.5 —
MCS output setup with respect to MCK tDDKHCS ns 3
266 MHz 2.5 —
Table 15. DDR2 SDRAM Input AC Timing Specifications (continued)At recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter Symbol Min Max Unit Note
MCK[n]
MCK[n]tMCK
MDQ[x]
MDQS[n]
tDISKEW
D1D0
tDISKEW
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
16 Freescale Semiconductor
DDR2 SDRAM
MCS output hold with respect to MCK tDDKHCX ns 3
266 MHz 2.5 —
MCK to MDQS Skew tDDKHMH –0.6 0.6 ns 4
MDQ/MDM output setup with respect to MDQS tDDKHDS,tDDKLDS
ns 5
266 MHz 0.9 —
MDQ/MDM output hold with respect to MDQS tDDKHDX,tDDKLDX
ps 5
266 MHz 1100 —
MDQS preamble start tDDKHMP 0.75 x tMCK — ns 6
MDQS epilogue end tDDKHME 0.4 x tMCK 0.6 x tMCK ns 6
Notes:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example, tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.
2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MDM/MDQS. For the ADDR/CMD
setup and hold specifications, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied cycle.
4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control of the DQSS override bits in the TIMING_CFG_2 register. This is typically set to the same delay as the clock adjusts in the CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same adjustment value. See the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual for a description and understanding of the timing modifications enabled by use of these bits.
5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.
6. tDDKHMP follows the symbol conventions described in note 1.
Table 16. DDR2 SDRAM Output AC Timing Specifications (continued)At recommended operating conditions with GVDD of 1.8V ± 100mV.
Parameter Symbol1 Min Max Unit Note
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 17
DDR2 SDRAM
The following figure shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).
Figure 5. Timing Diagram for tDDKHMH
The following figure shows the DDR2 SDRAM output timing diagram.
Figure 6. DDR2 SDRAM Output Timing Diagram
MDQS
MCK
MCKtMCK
MDQS
tDDKHMH(max) = 0.6 ns
tDDKHMH(min) = –0.6 ns
ADDR/CMD
tDDKHAS ,tDDKHCS
tDDKHMH
tDDKLDS
tDDKHDS
MDQ[x]/
MDQS[n]
MCK[n]
MCK[n]tMCK
tDDKLDX
tDDKHDX
D1D0
tDDKHAX ,tDDKHCX
Write A0 NOOP
tDDKHME
tDDKHMP
MECC[x]
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
18 Freescale Semiconductor
Local Bus
7 Local BusThis section describes the DC and AC electrical specifications for the local bus interface of the MPC8306.
7.1 Local Bus DC Electrical Characteristics
The following table provides the DC electrical characteristics for the local bus interface.
7.2 Local Bus AC Electrical Specifications
The following table describes the general timing parameters of the local bus interface of the MPC8306.
Table 17. Local Bus DC Electrical Characteristics
Parameter Symbol Min Max Unit
High-level input voltage VIH 2 OVDD + 0.3 V
Low-level input voltage VIL –0.3 0.8 V
High-level output voltage, IOH = –100 A VOH OVDD – 0.2 — V
Low-level output voltage, IOL = 100 A VOL — 0.2 V
Input current IIN — ±5 A
Table 18. Local Bus General Timing Parameters
Parameter Symbol1 Min Max Unit Note
Local bus cycle time tLBK 15 — ns 2
Input setup to local bus clock (LCLKn) tLBIVKH 7 — ns 3, 4
Input hold from local bus clock (LCLKn) tLBIXKH 1.0 — ns 3, 4
Local bus clock (LCLKn) to output valid tLBKHOV — 3 ns 3
Local bus clock (LCLKn) to output high impedance for LAD/LDP tLBKHOZ — 4 ns 5
Notes:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1).
2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of LCLK0 (for all other inputs).
3. All signals are measured from OVDD/2 of the rising/falling edge of LCLK0 to 0.4 OVDD of the signal in question for 3.3-V signaling levels.
4. Input timings are measured at the pin.5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 19
Local Bus
The following figure provides the AC test load for the local bus.
Figure 7. Local Bus AC Test Load
The following figures show the local bus signals. These figures has been given indicate timing parameters only and do not reflect actual functional operation of interface.
Figure 8. Local Bus Signals
Output Z0 = 50 OVDD/2RL = 50
Output Signals:LBCTL/LBCKE/LOE
tLBKHOV
tLBKHOV
LCLK[n]
Input Signals:LAD[0:15]
Output Signals:LAD[0:15]
tLBIXKHtLBIVKH
tLBKHOZ
tLBOTOT
LALE
Input Signal:LGTA
tLBIXKHtLBIVKH
tLBIXKH
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
20 Freescale Semiconductor
Local Bus
Figure 9. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 2
LCLK
UPM Mode Input Signal:LUPWAIT
tLBIXKHtLBIVKH
tLBIVKH
tLBIXKH
tLBKHOZ
T1
T3
Input Signals:LAD[0:15]/LDP[0:3]
UPM Mode Output Signals:LCS[0:3]/LBS[0:1]/LGPL[0:5]
GPCM Mode Output Signals:LCS[0:3]/LWE
tLBKHOV
tLBKHOV
tLBKHOZ
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 21
Ethernet and MII Management
Figure 10. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 4
8 Ethernet and MII ManagementThis section provides the AC and DC electrical characteristics for Ethernet interfaces.
8.1 Ethernet Controller (10/100 Mbps)—MII/RMII Electrical Characteristics
The electrical characteristics specified here apply to all MII (media independent interface) and RMII (reduced media independent interface), except MDIO (management data input/output) and MDC (management data clock). The MII and RMII are defined for 3.3 V. The electrical characteristics for MDIO and MDC are specified in Section 8.3, “Ethernet Management Interface Electrical Characteristics.”
8.1.1 DC Electrical Characteristics
All MII and RMII drivers and receivers comply with the DC parametric attributes specified in The following table.
LCLK
UPM Mode Input Signal:LUPWAIT
tLBIXKHtLBIVKH
tLBIVKH
tLBIXKH
tLBKHOZ
T1
T3
UPM Mode Output Signals:LCS[0:3]/LBS[0:1]/LGPL[0:5]
GPCM Mode Output Signals:LCS[0:3]/LWE
tLBKHOV
tLBKHOV
tLBKHOZ
T2
T4
Input Signals:LAD[0:15]
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
22 Freescale Semiconductor
Ethernet and MII Management
8.2 MII and RMII AC Timing Specifications
The AC timing specifications for MII and RMII are presented in this section.
8.2.1 MII AC Timing Specifications
This section describes the MII transmit and receive AC timing specifications.
8.2.1.1 MII Transmit AC Timing Specifications
The following table provides the MII transmit AC timing specifications.
Table 19. MII and RMII DC Electrical Characteristics
Parameter Symbol Conditions Min Max Unit
Supply voltage 3.3 V OVDD — 3 3.6 V
Output high voltage VOH IOH = –4.0 mA OVDD = Min 2.40 OVDD + 0.3 V
Output low voltage VOL IOL = 4.0 mA OVDD = Min GND 0.50 V
Input high voltage VIH — — 2.0 OVDD + 0.3 V
Input low voltage VIL — — –0.3 0.90 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 20. MII Transmit AC Timing SpecificationsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit
TX_CLK clock period 10 Mbps tMTX — 400 — ns
TX_CLK clock period 100 Mbps tMTX — 40 — ns
TX_CLK duty cycle tMTXH/tMTX 35 — 65 %
TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay tMTKHDX 1 5 15 ns
TX_CLK data clock rise VIL(min) to VIH(max) tMTXR 1.0 — 4.0 ns
TX_CLK data clock fall VIH(max) to VIL(min) tMTXF 1.0 — 4.0 ns
Note:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 23
Ethernet and MII Management
The following figure provides the AC test load.
Figure 11. AC Test Load
The following figure shows the MII transmit AC timing diagram.
Figure 12. MII Transmit AC Timing Diagram
8.2.1.2 MII Receive AC Timing Specifications
The following table provides the MII receive AC timing specifications.
Table 21. MII Receive AC Timing SpecificationsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit
RX_CLK clock period 10 Mbps tMRX — 400 — ns
RX_CLK clock period 100 Mbps tMRX — 40 — ns
RX_CLK duty cycle tMRXH/tMRX 35 — 65 %
RXD[3:0], RX_DV, RX_ER setup time to RX_CLK tMRDVKH 10.0 — — ns
RXD[3:0], RX_DV, RX_ER hold time to RX_CLK tMRDXKH 10.0 — — ns
RX_CLK clock rise VIL(min) to VIH(max) tMRXR 1.0 — 4.0 ns
RX_CLK clock fall time VIH(max) to VIL(min) tMRXF 1.0 — 4.0 ns
Note:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
Output Z0 = 50 OVDD/2RL = 50
TX_CLK
TXD[3:0]
tMTKHDX
tMTX
tMTXH
tMTXR
tMTXF
TX_ENTX_ER
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
24 Freescale Semiconductor
Ethernet and MII Management
The following figure shows the MII receive AC timing diagram.
Figure 13. MII Receive AC Timing Diagram
8.2.2 RMII AC Timing Specifications
This section describes the RMII transmit and receive AC timing specifications.
8.2.2.1 RMII Transmit AC Timing Specifications
The following table provides the RMII transmit AC timing specifications.
The following figure provides the AC test load.
Figure 14. AC Test Load
Table 22. RMII Transmit AC Timing SpecificationsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit
REF_CLK clock tRMX — 20 — ns
REF_CLK duty cycle tRMXH/tRMX 35 — 65 %
REF_CLK to RMII data TXD[1:0], TX_EN delay tRMTKHDX 2 — 13 ns
REF_CLK data clock rise VIL(min) to VIH(max) tRMXR 1.0 — 4.0 ns
REF_CLK data clock fall VIH(max) to VIL(min) tRMXF 1.0 — 4.0 ns
Note:1. The symbols used for timing specifications follow the pattern of t(first three letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMTKHDX symbolizes RMII transmit timing (RMT) for the time tRMX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tRMX represents the RMII(RM) reference (X) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
RX_CLK
RXD[3:0]
tMRDXKH
tMRX
tMRXH
tMRXR
tMRXF
RX_DVRX_ER
tMRDVKH
Valid Data
Output Z0 = 50 OVDD/2RL = 50
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 25
Ethernet and MII Management
The following figure shows the RMII transmit AC timing diagram.
Figure 15. RMII Transmit AC Timing Diagram
8.2.2.2 RMII Receive AC Timing Specifications
The following table provides the RMII receive AC timing specifications.
Table 23. RMII Receive AC Timing SpecificationsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit
REF_CLK clock period tRMX — 20 — ns
REF_CLK duty cycle tRMXH/tRMX 35 — 65 %
RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK tRMRDVKH 4.0 — — ns
RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK tRMRDXKH 2.0 — — ns
REF_CLK clock rise VIL(min) to VIH(max) tRMXR 1.0 — 4.0 ns
REF_CLK clock fall time VIH(max) to VIL(min) tRMXF 1.0 — 4.0 ns
Note:1. The symbols used for timing specifications follow the pattern of t(first three letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tRMRDVKH symbolizes RMII receive timing (RMR) with respect to the time data input signals (D) reach the valid state (V) relative to the tRMX clock reference (K) going to the high (H) state or setup time. Also, tRMRDXKL symbolizes RMII receive timing (RMR) with respect to the time data input signals (D) went invalid (X) relative to the tRMX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tRMX represents the RMII (RM) reference (X) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
REF_CLK
TXD[1:0]
tRMTKHDX
tRMX
tRMXH
tRMXR
tRMXF
TX_EN
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
26 Freescale Semiconductor
Ethernet and MII Management
The following figure shows the RMII receive AC timing diagram.
Figure 16. RMII Receive AC Timing Diagram
8.3 Ethernet Management Interface Electrical Characteristics
The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for MII, and RMII are specified in Section 8.1, “Ethernet Controller (10/100 Mbps)—MII/RMII Electrical Characteristics.”
8.3.1 MII Management DC Electrical Characteristics
MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The DC electrical characteristics for MDIO and MDC are provided in the following table.
8.3.2 MII Management AC Electrical Specifications
The following table provides the MII management AC timing specifications.
Table 24. MII Management DC Electrical Characteristics When Powered at 3.3 V
Parameter Symbol Conditions Min Max Unit
Supply voltage (3.3 V) OVDD — 3 3.6 V
Output high voltage VOH IOH = –1.0 mA OVDD = Min 2.40 OVDD + 0.3 V
Output low voltage VOL IOL = 1.0 mA OVDD = Min GND 0.50 V
Input high voltage VIH — 2.00 — V
Input low voltage VIL — — 0.80 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 25. MII Management AC Timing SpecificationsAt recommended operating conditions with OVDD is 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit Note
MDC frequency fMDC — 2.5 — MHz —
MDC period tMDC — 400 — ns —
MDC clock pulse width high tMDCH 32 — — ns —
REF_CLK
RXD[1:0]
tRMRDXKH
tRMX
tRMXH
tRMXR
tRMXF
CRS_DVRX_ER
tRMRDVKH
Valid Data
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 27
Ethernet and MII Management
The following figure shows the MII management AC timing diagram.
Figure 17. MII Management Interface Timing Diagram
MDC to MDIO delay tMDKHDX 10 — 70 ns —
MDIO to MDC setup time tMDDVKH 8.5 — — ns —
MDIO to MDC hold time tMDDXKH 0 — — ns —
MDC rise time tMDCR — — 10 ns —
MDC fall time tMDHF — — 10 ns —
Note:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
Table 25. MII Management AC Timing Specifications (continued)At recommended operating conditions with OVDD is 3.3 V ± 300mV.
Parameter/Condition Symbol1 Min Typical Max Unit Note
MDC
tMDDXKH
tMDC
tMDCH
tMDCR
tMDCF
tMDDVKH
tMDKHDX
MDIO
MDIO
(Input)
(Output)
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
28 Freescale Semiconductor
Ethernet and MII Management
8.4 IEEE 1588
8.4.1 DC Specifications
The IEEE 1588 DC timing specifications are given in the following table.
8.4.2 IEEE 1588 AC Specifications
The IEEE 1588 AC timing specifications are given in the following table.
Table 26. IEEE 1588 DC Electrical Characteristics
Characteristic Symbol Condition Min Max unit
Output high voltage VOH IOH = -8.0 mA 2.4 — V
Output low voltage VOL IOL = 8.0 mA — 0.5 V
Output low voltageVOL
IOL = 3.2mA— 0.4 V
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — - 0.3 0.8 V
Input current IIN 0V ≤ VIN ≤ OVDD — ± 5 μA
Table 27. IEEE 1588 AC Timing SpecificationsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter/Condition Symbol Min Typ Max Unit Note
QE_1588_CLK clock period tT1588CLK 2.5 — TRX_CLK 9 ns 1, 3
QE_1588_CLK duty cycle tT1588CLKH/tT1588CLK 40 50 60 % —
QE_1588_CLK peak-to-peak jitter tT1588CLKINJ — — 250 ps —
Rise time QE_1588_CLK (20%–80%)
tT1588CLKINR 1.0 — 2.0 ns —
Fall time QE_1588_CLK (80%–20%)
tT1588CLKINF 1.0 — 2.0 ns —
QE_1588_CLK_OUT clock period tT1588CLKOUT 2 tT1588CLK — — ns —
QE_1588_CLK_OUT duty cycle tT1588CLKOTH/tT1588CLKOUT
30 50 70 % —
QE_1588_PULSE_OUT tT1588OV 0.5 — 3.0 ns —
QE_1588_TRIG_IN pulse width tT1588TRIGH 2 tT1588CLK_MAX — — ns 2
Notes:1.TRX_CLK is the max clock period of QUICC engine receiving clock selected by TMR_CTRL[CKSEL]. See the MPC8306
PowerQUICC II Pro Integrated Communications Processor Family Reference Manual, for a description of TMR_CTRL registers.
2. It needs to be at least two times of clock period of clock selected by TMR_CTRL[CKSEL]. See the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual, for a description of TMR_CTRL registers.
3. The maximum value of tT1588CLK is not only defined by the value of TRX_CLK, but also defined by the recovered clock. For example, for 10/100 Mbps modes, the maximum value of tT1588CLK is 3600 and 280ns, respectively.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 29
TDM/SI
The following figure provides the data and command output timing diagram.
Figure 18. IEEE 1588 Output AC Timing
The following figure provides the data and command input timing diagram.
Figure 19. IEEE 1588 Input AC Timing
9 TDM/SIThis section describes the DC and AC electrical specifications for the time-division-multiplexed and serial interface of the MPC8306.
9.1 TDM/SI DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 TDM/SI.
Table 28. TDM/SI DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit
Output high voltage VOH IOH = –2.0 mA 2.4 — V
Output low voltage VOL IOL = 3.2 mA — 0.5 V
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN 0 V VIN OVDD — ±5 A
TSEC_1588_CLK_OUT
TSEC_1588_PULSE_OUTTSEC_1588_TRIG_OUT
tT1588OV
tT1588CLKOUT
tT1588CLKOUTH
Note: The output delay is count starting rising edge if tT1588CLKOUT is non-inverting. Otherwise, it iscount starting falling edge.
TSEC_1588_CLK
TSEC_1588_TRIG_INtT1588TRIGH
tT1588CLK
tT1588CLKH
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
30 Freescale Semiconductor
HDLC
9.2 TDM/SI AC Timing Specifications
The following table provides the TDM/SI input and output AC timing specifications.
The following figure provides the AC test load for the TDM/SI.
Figure 20. TDM/SI AC Test Load
The following figure represents the AC timing from Table 29. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge.
Figure 21. TDM/SI AC Timing (External Clock) Diagram
10 HDLCThis section describes the DC and AC electrical specifications for the high level data link control (HDLC), of the MPC8306.
Table 29. TDM/SI AC Timing Specifications1
Characteristic Symbol2 Min Max Unit
TDM/SI outputs—External clock delay tSEKHOV 2 14 ns
TDM/SI outputs—External clock High Impedance tSEKHOX 2 10 ns
TDM/SI inputs—External clock input setup time tSEIVKH 5 — ns
TDM/SI inputs—External clock input hold time tSEIXKH 2 — ns
Notes:1. Output specifications are measured from the 50% level of the rising edge of QE_CLK_IN to the 50% level of the signal.
Timings are measured at the pin.2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSEKHOX symbolizes the TDM/SI outputs external timing (SE) for the time tTDM/SI memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X).
Output Z0 = 50 OVDD/2RL = 50
TDM/SICLK (Input)
tSEIXKHtSEIVKH
tSEKHOV
Input Signals:TDM/SI
(See Note)
Output Signals:TDM/SI
(See Note)
Note: The clock edge is selectable on TDM/SI.
tSEKHOX
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 31
HDLC
10.1 HDLC DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 HDLC protocol.
10.2 HDLC AC Timing Specifications
The following table provides the input and output AC timing specifications for HDLC protocol.
The following figure provides the AC test load.
Figure 22. AC Test Load
Table 30. HDLC DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit
Output high voltage VOH IOH = –2.0 mA 2.4 — V
Output low voltage VOL IOL = 3.2 mA — 0.5 V
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 31. HDLC AC Timing Specifications1
Characteristic Symbol2 Min Max Unit
Outputs—Internal clock delay tHIKHOV 0 9 ns
Outputs—External clock delay tHEKHOV 1 12 ns
Outputs—Internal clock high impedance tHIKHOX 0 5.5 ns
Outputs—External clock high impedance tHEKHOX 1 8 ns
Inputs—Internal clock input setup time tHIIVKH 9 — ns
Inputs—External clock input setup time tHEIVKH 4 — ns
Inputs—Internal clock input hold time tHIIXKH 0 — ns
Inputs—External clock input hold time tHEIXKH 1 — ns
Notes:1. Output specifications are measured from the 50% level of the rising edge of QE_CLK_IN to the 50% level of the signal.
Timings are measured at the pin.2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tHIKHOX symbolizes the outputs internal timing (HI) for the time tserial memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X).
Output Z0 = 50 OVDD/2RL = 50
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
32 Freescale Semiconductor
USB
Figure 23 and Figure 24 represent the AC timing from Table 31. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge.
The following figure shows the timing with external clock.
Figure 23. AC Timing (External Clock) Diagram
The following figure shows the timing with internal clock.
Figure 24. AC Timing (Internal Clock) Diagram
11 USB
11.1 USB Controller
This section provides the AC and DC electrical specifications for the USB (ULPI) interface.
11.1.1 USB DC Electrical Characteristics
The following table provides the DC electrical characteristics for the USB interface.
11.1.2 USB AC Electrical Specifications
The following table describes the general timing parameters of the USB interface.
Serial CLK (Input)
tHEIXKHtHEIVKH
tHEKHOV
Input Signals:(See Note)
Output Signals:(See Note)
Note: The clock edge is selectable. tHEKHOX
Serial CLK (Output)
tHIIXKH
tHIKHOV
Input Signals:(See Note)
Output Signals:(See Note)
tHIIVKH
tHIKHOXNote: The clock edge is selectable.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 33
USB
The following figures provide the AC test load and signals for the USB, respectively.
Figure 25. USB AC Test Load
Figure 26. USB Signals
Table 32. USB DC Electrical Characteristics
Parameter Symbol Min Max Unit
High-level input voltage VIH 2.0 OVDD + 0.3 V
Low-level input voltage VIL –0.3 0.8 V
Input current IIN — ±5 A
High-level output voltage, IOH = –100 A VOH OVDD – 0.2 — V
Low-level output voltage, IOL = 100 A VOL — 0.2 V
Table 33. USB General Timing Parameters
Parameter Symbol1 Min Max Unit Note
USB clock cycle time tUSCK 15 — ns —
Input setup to USB clock—all inputs tUSIVKH 4 — ns —
input hold to USB clock—all inputs tUSIXKH 1 — ns —
USB clock to output valid—all outputs (except USBDR_STP_USBDR_STP)
tUSKHOV — 7 ns —
USB clock to output valid—USBDR_STP tUSKHOV — 7.5 ns —
Output hold from USB clock—all outputs tUSKHOX 2 — ns —
Note:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes USB timing (USB) for the input (I) to go invalid (X) with respect to the time the USB clock reference (K) goes high (H). Also, tUSKHOX symbolizes us timing (USB) for the USB clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time.
Output Z0 = 50 OVDD/2RL = 50
Output Signals
tUSKHOV
USBDR_CLK
Input Signals
tUSIXKHtUSIVKH
tUSKHOX
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
34 Freescale Semiconductor
DUART
12 DUARTThis section describes the DC and AC electrical specifications for the DUART interface of the MPC8306.
12.1 DUART DC Electrical Characteristics
The following table provides the DC electrical characteristics for the DUART interface of the MPC8306.
12.2 DUART AC Electrical Specifications
The following table provides the AC timing parameters for the DUART interface of the MPC8306.
Table 34. DUART DC Electrical Characteristics
Parameter Symbol Min Max Unit
High-level input voltage VIH 2 OVDD + 0.3 V
Low-level input voltage OVDD VIL –0.3 0.8 V
High-level output voltage, IOH = –100 A VOH OVDD – 0.2 — V
Low-level output voltage, IOL = 100 A VOL — 0.2 V
Input current (0 V VIN OVDD)1 IIN — ±5 A
Note:1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.
Table 35. DUART AC Timing Specifications
Parameter Value Unit Note
Minimum baud rate 256 baud —
Maximum baud rate >1,000,000 baud 1
Oversample rate 16 — 2
Notes:1. Actual attainable baud rate is limited by the latency of interrupt processing.2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are
sampled each 16th sample.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 35
eSDHC
13 eSDHCThis section describes the DC and AC electrical specifications for the eSDHC interface of the device.
13.1 eSDHC DC Electrical Characteristics
The following table provides the DC electrical characteristics for the eSDHC interface.
13.2 eSDHC AC Timing Specifications
The following table provides the eSDHC AC timing specifications as defined in Figure 27 and Figure 28.
Table 36. eSDHC Interface DC Electrical CharacteristicsAt recommended operating conditions with OVDD = 3.3 V
Characteristic Symbol Condition Min Max Unit Note
Input high voltage VIH — 0.625 OVDD — V 1
Input low voltage VIL — — 0.25 OVDD V 1
Output high voltage VOH IOH = –100 A at OVDD min
0.75 OVDD — V —
Output low voltage VOL IOL = 100 A at OVDD min
— 0.125 OVDD V —
Output high voltage VOH IOH = –100 mA OVDD – 0.2 — V 2
Output low voltage VOL IOL = 2 mA — 0.3 V 2
Input/output leakage current IIN/IOZ — –10 10 A —
Notes:
1. Note that the min VILand max VIH values are based on the respective min and max OVIN values found in Table 2..2. Open drain mode for MMC cards only.
Table 37. eSDHC AC Timing SpecificationsAt recommended operating conditions with OVDD = 3.3 V
Parameter Symbol1 Min Max Unit Notes
SD_CLK clock frequency: SD/SDIO Full-speed/High-speed modeMMC Full-speed/High-speed mode
fSHSCK 0 25/33.2520/52
MHz 2, 4
SD_CLK clock low time—Full-speed/High-speed mode tSHSCKL 10/7 — ns 4
SD_CLK clock high time—Full-speed/High-speed mode tSHSCKH 10/7 — ns 4
SD_CLK clock rise and fall times tSHSCKR/tSHSCKF
— 3 ns 4
Input setup times: SD_CMD, SD_DATx, SD_CD to SD_CLK
tSHSIVKH 5 — ns 4
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
36 Freescale Semiconductor
eSDHC
The following figure provides the eSDHC clock input timing diagram.
Figure 27. eSDHC Clock Input Timing Diagram
The following figure provides the data and command input/output timing diagram.
Figure 28. eSDHC Data and Command Input/Output Timing Diagram Referenced to Clock
Input hold times: SD_CMD, SD_DATx, SD_CD to SD_CLK
tSHSIXKH 2.5 — ns 3, 4
Output delay time: SD_CLK to SD_CMD, SD_DATx valid tSHSKHOV –3 3 ns 4
Notes:1. The symbols used for timing specifications herein follow the pattern of t(first three letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tFHSKHOV symbolizes eSDHC high-speed mode device timing (SHS) clock reference (K) going to the high (H) state, with respect to the output (O) reaching the invalid state (X) or output hold time. Note that in general, the clock reference symbol is based on five letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
2. In full-speed mode, the clock frequency value can be 0–25 MHz for an SD/SDIO card and 0–20 MHz for an MMC card. In high-speed mode, the clock frequency value can be 0–33.25 MHz for an SD/SDIO card and 0–52 MHz for an MMC card.
3. To satisfy hold timing, the delay difference between clock input and cmd/data input must not exceed 2 ns.4. CCARD 10 pF, (1 card), and CL = CBUS + CHOST + CCARD 40 pF
Table 37. eSDHC AC Timing Specifications (continued)At recommended operating conditions with OVDD = 3.3 V
Parameter Symbol1 Min Max Unit Notes
eSDHC
tSHSCKR
External Clock VMVMVM
tSHSCK
tSHSCKFVM = Midpoint Voltage (OVDD/2)
operational mode tSHSCKL tSHSCKH
VM = Midpoint Voltage (OVDD/2)
SD_CKExternal Clock
SD_DAT/CMD
VM VM VM VM
Inputs
SD_DAT/CMDOutputs
tSHSIVKH tSHSIXKH
tSHSKHOV
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 37
FlexCAN
14 FlexCANThis section describes the DC and AC electrical specifications for the FlexCAN interface.
14.1 FlexCAN DC Electrical Characteristics
The following table provides the DC electrical characteristics for the FlexCAN interface.
14.2 FlexCAN AC Timing Specifications
The following table provides the AC timing specifications for the FlexCAN interface.
Table 38. FlexCAN DC Electrical Characteristics (3.3V)For recommended operating conditions, see Table 2
Parameter Symbol Min Max Unit Notes
Input high voltage VIH 2 — V 1
Input low voltage VIL — 0.8 V 1
Input current (OVIN = 0 V or OVIN = OVDD) IIN — ±5 A 2
Output high voltage (OVDD = min, IOH = –2 mA) VOH 2.4 — V —
Output low voltage (OVDD = min, IOL = 2 mA) VOL — 0.4 V —
Note:1. Min VILand max VIH values are based on the respective min and max OVIN values found in Table 2.2. OVIN represents the input voltage of the supply. It is referenced in Table 2.
Table 39. FlexCAN AC Timing SpecificationsFor recommended operating conditions, see Table 2
Parameter Min Max Unit Notes
Baud rate 10 1000 Kbps —
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
38 Freescale Semiconductor
I2C
15 I2CThis section describes the DC and AC electrical characteristics for the I2C interface of the MPC8306.
15.1 I2C DC Electrical Characteristics
The following table provides the DC electrical characteristics for the I2C interface of the MPC8306.
15.2 I2C AC Electrical Specifications
The following table provides the AC timing parameters for the I2C interface of the MPC8306.
Table 40. I2C DC Electrical CharacteristicsAt recommended operating conditions with OVDD of 3.3 V ± 300mV.
Parameter Symbol Min Max Unit Notes
Input high voltage level VIH 0.7 OVDD OVDD + 0.3 V —
Input low voltage level VIL –0.3 0.3 OVDD V —
Low level output voltage VOL 0 0.4 V 1
Output fall time from VIH(min) to VIL(max) with a bus capacitance from 10 to 400 pF
tI2KLKV 20 + 0.1 CB 250 ns 2
Pulse width of spikes which must be suppressed by the input filter
tI2KHKL 0 50 ns 3
Capacitance for each I/O pin CI — 10 pF —
Input current (0 V VIN OVDD) IIN — ±5 A 4
Notes:1. Output voltage (open drain or open collector) condition = 3 mA sink current.2. CB = capacitance of one bus line in pF.3. Refer to the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual for information
on the digital filter used.4. I/O pins obstructs the SDA and SCL lines if OVDD is switched off.
Table 41. I2C AC Electrical SpecificationsAll values refer to VIH (min) and VIL (max) levels (see Table 40).
Parameter Symbol1 Min Max Unit
SCL clock frequency fI2C 0 400 kHz
Low period of the SCL clock tI2CL 1.3 — s
High period of the SCL clock tI2CH 0.6 — s
Setup time for a repeated START condition tI2SVKH 0.6 — s
Hold time (repeated) START condition (after this period, the first clock pulse is generated)
tI2SXKL 0.6 — s
Data setup time tI2DVKH 100 — ns
Data hold time: I2C bus devices tI2DXKL 300 0.93 s
Rise time of both SDA and SCL signals tI2CR 20 + 0.1 CB4 300 ns
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 39
I2C
The following figure provides the AC test load for the I2C.
Figure 29. I2C AC Test Load
The following figure shows the AC timing diagram for the I2C bus.
Figure 30. I2C Bus AC Timing Diagram
Fall time of both SDA and SCL signals tI2CF 20 + 0.1 CB4 300 ns
Setup time for STOP condition tI2PVKH 0.6 — s
Bus free time between a STOP and START condition tI2KHDX 1.3 — s
Noise margin at the LOW level for each connected device (including hysteresis)
VNL 0.1 OVDD — V
Noise margin at the HIGH level for each connected device (including hysteresis)
VNH 0.2 OVDD — V
Notes:1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
2. MPC8306 provides a hold time of at least 300 ns for the SDA signal (referred to the VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.
3. The maximum tI2DVKL has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal.4. CB = capacitance of one bus line in pF.
Table 41. I2C AC Electrical Specifications (continued)All values refer to VIH (min) and VIL (max) levels (see Table 40).
Parameter Symbol1 Min Max Unit
Output Z0 = 50 OVDD/2RL = 50
SrS
SDA
SCL
tI2CF
tI2SXKL
tI2CL
tI2CHtI2DXKL
tI2DVKH
tI2SXKL
tI2SVKH
tI2KHKL
tI2PVKH
tI2CR
tI2CF
P S
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
40 Freescale Semiconductor
Timers
16 TimersThis section describes the DC and AC electrical specifications for the timers of the MPC8306.
16.1 Timer DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 timer pins, including TIN, TOUT, TGATE, and RTC_PIT_CLK.
16.2 Timer AC Timing Specifications
The following table provides the timer input and output AC timing specifications.
The following figure provides the AC test load for the timers.
Figure 31. Timers AC Test Load
Table 42. Timer DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit
Output high voltage VOH IOH = –6.0 mA 2.4 — V
Output low voltage VOL IOL = 6.0 mA — 0.5 V
Output low voltage VOL IOL = 3.2 mA — 0.4 V
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 43. Timer Input AC Timing Specifications1
Characteristic Symbol2 Min Unit
Timers inputs—minimum pulse width tTIWID 20 ns
Notes:1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.2. Timer inputs and outputs are asynchronous to any visible clock. Timer outputs should be synchronized before use by any
external synchronous logic. Timer inputs are required to be valid for at least tTIWID ns to ensure proper operation.
Output Z0 = 50 OVDD/2RL = 50
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 41
GPIO
17 GPIOThis section describes the DC and AC electrical specifications for the GPIO of the MPC8306.
17.1 GPIO DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 GPIO.
17.2 GPIO AC Timing Specifications
The following table provides the GPIO input and output AC timing specifications.
The following figure provides the AC test load for the GPIO.
Figure 32. GPIO AC Test Load
Table 44. GPIO DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit Notes
Output high voltage VOH IOH = –6.0 mA 2.4 — V 1
Output low voltage VOL IOL = 6.0 mA — 0.5 V 1
Output low voltage VOL IOL = 3.2 mA — 0.4 V 1
Input high voltage VIH — 2.0 OVDD + 0.3 V 1
Input low voltage VIL — –0.3 0.8 V —
Input current IIN 0 V VIN OVDD — ±5 A —
Note: 1. This specification applies when operating from 3.3-V supply.
Table 45. GPIO Input AC Timing Specifications1
Characteristic Symbol2 Min Unit
GPIO inputs—minimum pulse width tPIWID 20 ns
Notes:1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by any
external synchronous logic. GPIO inputs are required to be valid for at least tPIWID ns to ensure proper operation.
Output Z0 = 50 OVDD/2RL = 50
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
42 Freescale Semiconductor
IPIC
18 IPICThis section describes the DC and AC electrical specifications for the external interrupt pins of the MPC8306.
18.1 IPIC DC Electrical Characteristics
The following table provides the DC electrical characteristics for the external interrupt pins of the MPC8306.
18.2 IPIC AC Timing Specifications
The following table provides the IPIC input and output AC timing specifications.
19 SPIThis section describes the DC and AC electrical specifications for the SPI of the MPC8306.
19.1 SPI DC Electrical Characteristics
The following table provides the DC electrical characteristics for the MPC8306 SPI.
Table 46. IPIC DC Electrical Characteristics1,2
Characteristic Symbol Condition Min Max Unit
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN — — ±5 A
Output High Voltage VOH IOL = -8.0 mA 2.4 — V
Output low voltage VOL IOL = 6.0 mA — 0.5 V
Output low voltage VOL IOL = 3.2 mA — 0.4 V
Notes:1. This table applies for pins IRQ, MCP_OUT, and QE ports Interrupts.2. MCP_OUT is open drain pins, thus VOH is not relevant for those pins.
Table 47. IPIC Input AC Timing Specifications1
Characteristic Symbol2 Min Unit
IPIC inputs—minimum pulse width tPIWID 20 ns
Notes:1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of SYS_CLK_IN.
Timings are measured at the pin.2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by any
external synchronous logic. IPIC inputs are required to be valid for at least tPIWID ns to ensure proper operation when working in edge triggered mode.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 43
SPI
19.2 SPI AC Timing Specifications
The following table and provide the SPI input and output AC timing specifications.
The following figure provides the AC test load for the SPI.
Figure 33. SPI AC Test Load
Figure 34 and Figure 35 represent the AC timing from Table 49. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge.
Table 48. SPI DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit
Output high voltage VOH IOH = –6.0 mA 2.4 — V
Output low voltage VOL IOL = 6.0 mA — 0.5 V
Output low voltage VOL IOL = 3.2 mA — 0.4 V
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 49. SPI AC Timing Specifications1
Characteristic Symbol2 Min Max Unit
SPI outputs—Master mode (internal clock) delay tNIKHOV 0.5 6 ns
SPI outputs—Slave mode (external clock) delay tNEKHOV 2 8 ns
SPI inputs—Master mode (internal clock) input setup time tNIIVKH 6 — ns
SPI inputs—Master mode (internal clock) input hold time tNIIXKH 0 — ns
SPI inputs—Slave mode (external clock) input setup time tNEIVKH 4 — ns
SPI inputs—Slave mode (external clock) input hold time tNEIXKH 2 — ns
Notes:1. Output specifications are measured from the 50% level of the rising edge of SPICLK to the 50% level of the signal. Timings
are measured at the pin.2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOV symbolizes the NMSI outputs internal timing (NI) for the time tSPI memory clock reference (K) goes from the high state (H) until outputs (O) are valid (V).
3. All units of output delay must be enabled for 8306 output port spimosi (SPI Master Mode)4. delay units must not be enabled for Slave Mode.
Output Z0 = 50 OVDD/2RL = 50
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
44 Freescale Semiconductor
JTAG
The following figure shows the SPI timing in slave mode (external clock).
Figure 34. SPI AC Timing in Slave Mode (External Clock) Diagram
The following figure shows the SPI timing in master mode (internal clock).
Figure 35. SPI AC Timing in Master Mode (Internal Clock) Diagram
20 JTAGThis section describes the DC and AC electrical specifications for the IEEE Std. 1149.1™ (JTAG) interface of the MPC8306.
20.1 JTAG DC Electrical Characteristics
The following table provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface of the MPC8306.
Table 50. JTAG Interface DC Electrical Characteristics
Characteristic Symbol Condition Min Max Unit
Output high voltage VOH IOH = –6.0 mA 2.4 — V
Output low voltage VOL IOL = 6.0 mA — 0.5 V
Output low voltage VOL IOL = 3.2 mA — 0.4 V
SPICLK (Input)
tNEIXKHtNEIVKH
tNEKHOV
Input Signals:SPIMOSI
(See Note)
Output Signals:SPIMISO
(See Note)
Note: The clock edge is selectable on SPI.
SPICLK (Output)
tNIIXKH
tNIKHOV
Input Signals:SPIMISO
(See Note)
Output Signals:SPIMOSI
(See Note)
Note: The clock edge is selectable on SPI.
tNIIVKH
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 45
JTAG
20.2 JTAG AC Electrical Characteristics
This section describes the AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface of the MPC8306. The following table provides the JTAG AC timing specifications as defined in Figure 37 through Figure 40.
Input high voltage VIH — 2.0 OVDD + 0.3 V
Input low voltage VIL — –0.3 0.8 V
Input current IIN 0 V VIN OVDD — ±5 A
Table 51. JTAG AC Timing Specifications (Independent of SYS_CLK_IN)1
At recommended operating conditions (see Table 2).
Parameter Symbol2 Min Max Unit Notes
JTAG external clock frequency of operation fJTG 0 33.3 MHz —
JTAG external clock cycle time t JTG 30 — ns —
JTAG external clock pulse width measured at 1.4 V tJTKHKL 11 — ns —
JTAG external clock rise and fall times tJTGR, tJTGF 0 2 ns —
TRST assert time tTRST 25 — ns 3
Input setup times:Boundary-scan data
TMS, TDItJTDVKHtJTIVKH
44
——
ns4
Input hold times:Boundary-scan data
TMS, TDItJTDXKHtJTIXKH
1010
——
ns4
Valid times:Boundary-scan data
TDOtJTKLDVtJTKLOV
22
1515
ns5
Table 50. JTAG Interface DC Electrical Characteristics (continued)
Characteristic Symbol Condition Min Max Unit
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
46 Freescale Semiconductor
JTAG
The following figure provides the AC test load for TDO and the boundary-scan outputs of the MPC8306.
Figure 36. AC Test Load for the JTAG Interface
The following figure provides the JTAG clock input timing diagram.
Figure 37. JTAG Clock Input Timing Diagram
The following figure provides the TRST timing diagram.
Figure 38. TRST Timing Diagram
Output hold times:Boundary-scan data
TDOtJTKLDXtJTKLOX
22
——
ns5
JTAG external clock to output high impedance:Boundary-scan data
TDOtJTKLDZtJTKLOZ
22
199
ns5, 6
6
Notes:1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.
The output timings are measured at the pins. All output timings assume a purely resistive 50-load (see Figure 36). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.4. Non-JTAG signal input timing with respect to tTCLK.5. Non-JTAG signal output timing with respect to tTCLK.6. Guaranteed by design and characterization.
Table 51. JTAG AC Timing Specifications (Independent of SYS_CLK_IN)1 (continued)At recommended operating conditions (see Table 2).
Parameter Symbol2 Min Max Unit Notes
Output Z0 = 50 OVDD/2RL = 50
JTAG
tJTKHKL tJTGR
External Clock VMVMVM
tJTG tJTGF
VM = Midpoint Voltage (OVDD/2)
TRST
VM = Midpoint Voltage (OVDD/2)
VM VM
tTRST
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 47
JTAG
The following figure provides the boundary-scan timing diagram.
Figure 39. Boundary-Scan Timing Diagram
The following figure provides the test access port timing diagram.
Figure 40. Test Access Port Timing Diagram
VM = Midpoint Voltage (OVDD/2)
VM VM
tJTDVKHtJTDXKH
BoundaryData Outputs
BoundaryData Outputs
JTAGExternal Clock
BoundaryData Inputs
Output Data Valid
tJTKLDX
tJTKLDZ
tJTKLDV
InputData Valid
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
VM VM
tJTIVKHtJTIXKH
JTAGExternal Clock
Output Data Valid
tJTKLOX
tJTKLOZ
tJTKLOV
InputData Valid
Output Data Valid
TDI, TMS
TDO
TDO
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
48 Freescale Semiconductor
Package and Pin Listings
21 Package and Pin ListingsThis section details package parameters, pin assignments, and dimensions. The MPC8306 is available in a thermally enhanced MAPBGA (mold array process-ball grid array); see Section 21.1, “Package Parameters for the MPC8306,” and Section 21.2, “Mechanical Dimensions of the MPC8306 MAPBGA,” for information on the MAPBGA.
21.1 Package Parameters for the MPC8306
The package parameters are as provided in the following list.
Package outline 19 mm 19 mm
Package Type MAPBGA
Interconnects 369
Pitch 0.80 mm
Module height (typical) 1.48 mm; Min = 1.31mm and Max 1.61mm
Solder Balls 96 Sn / 3.5 Ag / 0.5 Cu (VM package)
Ball diameter (typical) 0.40 mm
21.2 Mechanical Dimensions of the MPC8306 MAPBGAThe following figure shows the mechanical dimensions and bottom surface nomenclature of the MPC8306, 369-MAPBGA package.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 49
Package and Pin Listings
Figure 41. Mechanical Dimensions and Bottom Surface Nomenclature of the MPC8306 MAPBGA
Notes:1. All dimensions are in millimeters.2. Dimensions and tolerances per ASME Y14.5M-1994.3. Maximum solder ball diameter measured parallel to datum A.4. Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
50 Freescale Semiconductor
Package and Pin Listings
21.3 Pinout Listings
Following table shows the pin list of the MPC8306.
Table 52. MPC8306 Pinout Listing
Signal Package Pin Number Pin Type Power Supply Notes
DDR Memory Controller Interface
MEMC_MDQ[0] W5 IO GVDD —
MEMC_MDQ[1] V4 IO GVDD —
MEMC_MDQ[2] Y4 IO GVDD —
MEMC_MDQ[3] AB1 IO GVDD —
MEMC_MDQ[4] AA1 IO GVDD —
MEMC_MDQ[5] Y2 IO GVDD —
MEMC_MDQ[6] Y1 IO GVDD —
MEMC_MDQ[7] W2 IO GVDD —
MEMC_MDQ[8] G2 IO GVDD —
MEMC_MDQ[9] G1 IO GVDD —
MEMC_MDQ[10] F1 IO GVDD —
MEMC_MDQ[11] E2 IO GVDD —
MEMC_MDQ[12] E1 IO GVDD —
MEMC_MDQ[13] E4 IO GVDD —
MEMC_MDQ[14] F4 IO GVDD —
MEMC_MDQ[15] D1 IO GVDD —
MEMC_MDM[0] AB2 O GVDD —
MEMC_MDM[1] G4 O GVDD —
MEMC_MDQS[0] V5 IO GVDD —
MEMC_MDQS[1] F5 IO GVDD —
MEMC_MBA[0] L2 O GVDD —
MEMC_MBA[1] L1 O GVDD —
MEMC_MBA[2] R4 O GVDD —
MEMC_MA[0] M1 O GVDD —
MEMC_MA[1] M4 O GVDD —
MEMC_MA[2] N1 O GVDD —
MEMC_MA[3] N2 O GVDD —
MEMC_MA[4] P1 O GVDD —
MEMC_MA[5] N4 O GVDD —
MEMC_MA[6] P2 O GVDD —
MEMC_MA[7] R1 O GVDD —
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 51
Package and Pin Listings
MEMC_MA[8] T1 O GVDD —
MEMC_MA[9] P4 O GVDD —
MEMC_MA[10] L4 O GVDD —
MEMC_MA[11] T2 O GVDD —
MEMC_MA[12] U1 O GVDD —
MEMC_MA[13] U2 O GVDD —
MEMC_MWE_B K1 O GVDD —
MEMC_MRAS_B K2 O GVDD —
MEMC_MCAS_B J1 O GVDD —
MEMC_MCS_B[0] J4 O GVDD —
MEMC_MCS_B[1] H1 O GVDD —
MEMC_MCKE[0] U4 O GVDD —
MEMC_MCK[0] V1 O GVDD —
MEMC_MCK_B[0] W1 O GVDD —
MEMC_MODT[0] H2 O GVDD —
MEMC_MODT[1] H4 O GVDD —
MEMC_MVREF L8 GVDD —
Local Bus Controller Interface
LAD[0] B7 IO OVDD —
LAD[1] D9 IO OVDD —
LAD[2] A6 IO OVDD —
LAD[3] B8 IO OVDD —
LAD[4] A7 IO OVDD —
LAD[5] A8 IO OVDD —
LAD[6] A9 IO OVDD —
LAD[7] D10 IO OVDD —
LAD[8] B10 IO OVDD —
LAD[9] A10 IO OVDD —
LAD[10] B11 IO OVDD —
LAD[11] D12 IO OVDD —
LAD[12] D11 IO OVDD —
LAD[13] A11 IO OVDD —
LAD[14] A12 IO OVDD —
LAD[15] B13 IO OVDD —
LA[16] A13 IO OVDD —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
52 Freescale Semiconductor
Package and Pin Listings
LA[17] B14 O OVDD —
LA[18] A14 O OVDD —
LA[19] A15 O OVDD —
LA[20] A16 O OVDD —
LA[21] B16 O OVDD —
LA[22] A17 O OVDD —
LA[23] B17 O OVDD —
LA[24] A18 O OVDD —
LA[25] B19 O OVDD —
LCS_B[0] A19 O OVDD 3
LCS_B[1] B20 O OVDD 3
LCS_B[2] A20 O OVDD 3
LCS_B[3] A21 O OVDD 3
LCLK[0] D13 O OVDD —
LGPL[0] B22 O OVDD —
LGPL[1] D16 O OVDD —
LGPL[2] D19 O OVDD —
LGPL[3] D17 O OVDD —
LGPL[4] E18 IO OVDD —
LGPL[5] E19 O OVDD —
LWE_B[0] D15 O OVDD —
LWE_B[1] D14 O OVDD —
LBCTL A22 O OVDD —
LALE B23 O OVDD —
JTAG
TCK A3 I OVDD —
TDI B5 I OVDD 3
TDO D7 O OVDD —
TMS A4 I OVDD 3
TRST_B D8 I OVDD 3
Test Interface
TEST_MODE A5 I OVDD —
System Control Signals
HRESET_B U20 IO OVDD 1
PORESET_B V20 I OVDD —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 53
Package and Pin Listings
Clock Interface
QE_CLK_IN P23 I OVDD —
SYS_CLK_IN R23 I OVDD —
RTC_PIT_CLOCK V23 I OVDD —
Miscellaneous Signals
QUIESCE_B A2 O OVDD —
THERM0 D6 I OVDD —
GPIO
GPIO[0]/RXCAN1/ SD_CLK/MSRCID0 (DDR ID) E5 IO OVDD —
GPIO[1]/TXCAN1/SD_CMD/MSRCID1 (DDR ID) E6 IO OVDD —
GPIO[2]/RXCAN2/SD_CD/MSRCID2 (DDR ID) D4 IO OVDD —
GPIO[3]/TXCAN2/SD_WP/MSRCID3 (DDR ID) C2 IO OVDD —
GPIO[4]/RXCAN3/SD_DAT0/MSRCID4 (DDR ID) C1 IO OVDD —
GPIO[5]/TXCAN3/SD_DAT1/MDVAL (DDR ID) B1 IO OVDD —
GPIO[6]/RXCAN4/SD_DAT2/QE_EXT_REQ_3 B3 IO OVDD —
GPIO[7]/TXCAN4/SD_DAT3/QE_EXT_REQ_1 B2 IO OVDD —
USB
USBDR_PWRFAULT/IIC_SDA2/CE_PIO_1 AC4 IO OVDD 2
USBDR_CLK/UART2_SIN[2]/UART2_CTS_B[1] Y9 I OVDD
USBDR_DIR/IIC_SCL2 AC3 IO OVDD 2
USBDR_NXT/UART2_SIN[1]/QE_EXT_REQ_4 AC2 IO OVDD —
USBDR_PCTL[0]/UART2_SOUT[1]/LB_POR_CFG_BOOT_ECC
AB3 IO OVDD —
USBDR_PCTL[1]/UART2_SOUT[2]/UART2_RTS_B1/LB_POR_BOOT_ERR
Y8 O OVDD —
USBDR_STP/QE_EXT_REQ_2 W6 IO OVDD —
USBDR_TXDRXD[0]/UART1_SOUT[1]/GPIO[32]/QE_TRB_O
AB7 IO OVDD —
USBDR_TXDRXD[1]/UART1_SIN[1]/GPIO[33]/QE_TRB_I
AB8 IO OVDD —
USBDR_TXDRXD[2]/UART1_SOUT[2]/UART1_RTS_B1/QE_BRG[1]
AC6 IO OVDD —
USBDR_TXDRXD[3]/UART1_SIN[2]/UART1_CTS_B1/QE_BRG[2]
AC5 IO OVDD —
USBDR_TXDRXD[4]/GPIO[34]/QE_BRG[3] AB5 IO OVDD —
USBDR_TXDRXD[5]/GPIO[35]/QE_BRG[4] Y7 IO OVDD —
USBDR_TXDRXD[6]/GPIO[36]/QE_BRG[9] Y6 IO OVDD —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
54 Freescale Semiconductor
Package and Pin Listings
USBDR_TXDRXD[7]/GPIO[37]/QE_BRG[11] Y5 IO OVDD —
DUART
UART1_SOUT[1]/LSRCID4/LCS_B[4] C23 O OVDD —
UART1_SIN[1]/LDVAL/LCS_B[5] F19 IO OVDD —
UART1_SOUT[2]/UART1_RTS_B1/LCS_B[6] D23 O OVDD —
UART1_SIN[2]/UART1_CTS_B[1]/LCS_B[7] D22 IO OVDD —
Interrupts
IRQ_B0_MCP_IN_B/CE_PI_0 E20 IO OVDD —
IRQ_B1/MCP_OUT_B E23 IO OVDD —
IRQ_B2/CKSTOP_OUT_B E22 IO OVDD —
IRQ_B3/CKSTOP_IN_B F20 I OVDD —
I2C / SPI
IIC_SDA1 G20 IO OVDD 2
IIC_SCL1 J20 IO OVDD 2
LCLK1/IIC_SCL2/CKSTOP_IN_B H20 IO OVDD 2
SPISEL_BOOT/IIC_SDA2/CKSTOP_OUT_B F23 O OVDD 2
SPIMOSI/LSRCID[2] G22 IO OVDD —
SPIMISO/LSRCID[3] K20 IO OVDD —
SPICLK/LSRCID[0] G23 IO OVDD —
SPISEL/LSRCID[1] H22 I OVDD —
FEC Management
FEC_MDC H23 O OVDD —
FEC_MDIO L20 IO OVDD —
FEC1/GTM/GPIO
FEC1_COL/GTM1_TIN[1]/GPIO[16] AB20 IO OVDD —
FEC1_CRS/GTM1_TGATE1_B/GPIO[17] AC21 IO OVDD —
FEC1_RX_CLK/GPIO[18] Y17 IO OVDD —
FEC1_RX_DV/GTM1_TIN[2]/GPIO[19] Y18 IO OVDD —
FEC1_RX_ER/GTM1_TGATE[2]_B/GPIO[20] AB19 IO OVDD —
FEC1_RXD0/GPIO[21] AC20 IO OVDD —
FEC1_RXD1/GTM1_TIN[3]/GPIO[22] AC19 IO OVDD —
FEC1_RXD2/GTM1_TGATE[3]_B/GPIO[23] AC18 IO OVDD —
FEC1_RXD3/GPIO[24] AB17 IO OVDD —
FEC1_TX_CLK/GTM1_TIN4/GPIO[25] Y15 IO OVDD —
FEC1_TX_EN/GTM1_TGATE[4]_B/GPIO[26] Y16 IO OVDD —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 55
Package and Pin Listings
FEC1_TX_ER/GTM1_TOUT[4]_B/GPIO[27] AC17 IO OVDD —
FEC1_TXD0/GTM1_TOUT[1]_B/GPIO[28] AB16 IO OVDD —
FEC1_TXD1/GTM1_TOUT[2]_B/GPIO[29] AC16 IO OVDD —
FEC1_TXD2/GTM1_TOUT[3]_B/GPIO[30] AC15 IO OVDD —
FEC1_TXD3/GPIO[31] AB14 IO OVDD —
FEC2/GPIO
FEC2_COL/GPIO[32] AC14 IO OVDD —
FEC2_CRS/GPIO[33] AB13 IO OVDD —
FEC2_RX_CLK/GPIO[34] Y14 IO OVDD —
FEC2_RX_DV/GPIO[35] AC13 IO OVDD —
FEC2_RX_ER/GPIO[36] Y13 IO OVDD —
FEC2_RXD0/GPIO[37] AC12 IO OVDD —
FEC2_RXD1/GPIO[38] AB11 IO OVDD —
FEC2_RXD2/GPIO[39] AC11 IO OVDD —
FEC2_RXD3/GPIO[40] AB10 IO OVDD —
FEC2_TX_CLK/GPIO[41] Y12 IO OVDD —
FEC2_TX_EN/GPIO[42] AC10 IO OVDD —
FEC2_TX_ER/GPIO[43] AC9 IO OVDD —
FEC2_TXD0/GPIO[44] AC8 IO OVDD —
FEC2_TXD1/GPIO[45] Y11 IO OVDD —
FEC2_TXD2/GPIO[46] AC7 IO OVDD —
FEC2_TXD3/GPIO[47] Y10 IO OVDD —
FEC3/GPIO
FEC3_COL/GPIO[48] J23 IO OVDD —
FEC3_CRS/GPIO[49] K23 IO OVDD —
FEC3_RX_CLK/GPIO[50] M20 IO OVDD —
FEC3_RX_DV/FEC1_TMR_TX_ESFD/GPIO[51] K22 IO OVDD —
FEC3_RX_ER/FEC1_TMR_RX_ESFD/GPIO[52] L22 IO OVDD —
FEC3_RXD0/FEC2_TMR_TX_ESFD/GPIO[53] L23 IO OVDD —
FEC3_RXD1/FEC2_TMR_RX_ESFD/GPIO[54] M23 IO OVDD —
FEC3_RXD2/TSEC_TMR_TRIG1/GPIO[55] N22 IO OVDD —
FEC3_RXD3/TSEC_TMR_TRIG2/GPIO[56] N23 IO OVDD —
FEC3_TX_CLK/TSEC_TMR_CLK/GPIO[57] N20 IO OVDD —
FEC3_TX_EN/TSEC_TMR_GCLK/GPIO[58] P20 IO OVDD —
FEC3_TX_ER/TSEC_TMR_PP1/GPIO[59] P22 IO OVDD —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
56 Freescale Semiconductor
Package and Pin Listings
FEC3_TXD0/TSEC_TMR_PP2/GPIO[60] R20 IO OVDD —
FEC3_TXD1/TSEC_TMR_PP3/GPIO[61] T22 IO OVDD —
FEC3_TXD2/TSEC_TMR_ALARM1/GPIO[62] T23 IO OVDD —
FEC3_TXD3/TSEC_TMR_ALARM2/GPIO[63] T20 IO OVDD —
HDLC/GPIO/TDM
HDLC1_RXCLK/TDM1_RCK/GPIO[1] U23 IO OVDD —
HDLC1_RXD/TDM1_RD/GPIO[3] U22 IO OVDD —
HDLC1_TXCLK/GPIO[0]/TDM1_TCK/QE_BRG[5]
AC22 IO OVDD —
HDLC1_TXD/GPIO[2]/TDM1_TD/CFG_RESET_SOURCE[0]
W18 IO OVDD —
HDLC1_CD_B/GPIO[4]/TDM1_TFS W19 IO OVDD —
HDLC1_CTS_B/GPIO[5]/TDM1_RFS Y20 IO OVDD —
HDLC1_RTS_B/GPIO[6]/TDM1_STROBE_B/CFG_RESET_SOURCE[1]
AB22 IO OVDD —
HDLC2_TXCLK/GPIO[16]/TDM2_TCK/QE_BRG[7]
AB23 IO OVDD —
HDLC2_RXCLK/GPIO[17]/TDM2_RCK/QE_BRG[8]
AA23 IO OVDD —
HDLC2_TXD/GPIO[18]/TDM2_TD/CFG_RESET_SOURCE[2]
W20 IO OVDD —
HDLC2_RXD/GPIO[19]/TDM2_RD Y23 IO OVDD —
HDLC2_CD_B/GPIO[20]/TDM2_TFS Y22 IO OVDD —
HDLC2_CTS_B/GPIO[21]/TDM2_RFS W23 IO OVDD —
HDLC2_RTS_B/GPIO[22]/TDM2_STROBE_B/CFG_RESET_SOURCE[3]
W22 IO OVDD —
Power
AVDD1 L16 — — —
AVDD2 M16 — — —
AVDD3 N8 — — —
GVDD G5, H5, J5, K5, L5, M5, N5, P5, R5, T5, U5
— — —
OVDD E7,E8,E9,E10,E11,E12,E13,E14, E15,
E16,E17,G19,H19,J19,K19,L19,M19,
N19,P19,R19,T19,U19,W7,W8,W9, W10,W11, W12,W13, W14,W15,
W16, W17
— — —
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 57
Package and Pin Listings
VDD H8,H9,H10,H11,H12,H13,H14,H15,H16,J8,J16,K8,K16,M8,N16,P8,P16,R8,R16,T8,T9,T10,T11,T1
2,T13,T14,T15,T16
— — —
VSS A1,B4,B6,B9,B12,B15,B18,B21,C22,D2,D5,D18,D20,F2,F22,J2,J9,J10,J11,J12,J13,J14,J15,J22,K4,K9,K10,K11,K12,K13,K14,K15,L9,L10,L11,L12,L13,L14,L15,M2,M9,M10,M11,M12,M13,M14,M15,M22,N9,N10,N11,N12,N13,N14,N15,P9,P10,P11,P12,P13,P14,P15,R2,R9,R10,R11,R12,R13,R14,R15,R22,T4,V2,V19,V22,W4,Y19,AA2,AA22,AB4,AB6,AB9,AB12,AB15,AB18,AB21,AC1,AC23
— — —
NC A23 — — —
Notes1. This pin is an open drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to OVDD 2. This pin is an open drain signal. A weak pull-up resistor (2-10 kΩ) should be placed on this pin to OVDD 3. This pin has weak pull-up that is always enabled.
Table 52. MPC8306 Pinout Listing (continued)
Signal Package Pin Number Pin Type Power Supply Notes
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
58 Freescale Semiconductor
Clocking
22 ClockingThe following figure shows the internal distribution of clocks within the MPC8306.
Figure 42. MPC8306 Clock Subsystem
Figure 43. The primary clock source for MPC8306 is SYS_CLK_IN.
Core PLL
System
LBCLCLK[0:1]
core_clk
e300c3 core
csb_clk to rest
csb_clk
Local Bus
ClockUnit
of the device
lbc_clk
QE PLL
SYS_CLK_IN
MemoryDevice
/n
to local bus
Clock
MEMC_MCK
MEMC_MCK
DDR
ddr_clk
DDRMemoryDevice
PLL
to DDRmemorycontroller
Clock
/2Divider
Divider
qe_clk
MPC8306
CLK GenQE_CLK_IN QE Block
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 59
Clocking
22.1 System Clock Domains
As shown in Figure 42, the primary clock input (frequency) is multiplied up by the system phase-locked loop (PLL) and the clock unit to create four major clock domains:
• The coherent system bus clock (csb_clk)
• The QUICC Engine clock (qe_clk)
• The internal clock for the DDR controller (ddr_clk)
• The internal clock for the local bus controller (lbc_clk)
The csb_clk frequency is derived from the following equation:
csb_clk = SYS_CLK_IN × SPMF Eqn. 1
The csb_clk serves as the clock input to the e300 core. A second PLL inside the core multiplies up the csb_clk frequency to create the internal clock for the core (core_clk). The system and core PLL multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL) which is loaded at power-on reset or by one of the hard-coded reset options. For more information, see the Reset Configuration chapter in the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual.
The qe_clk frequency is determined by the QUICC Engine PLL multiplication factor (RCWL[CEPMF]) and the QUICC Engine PLL division factor (RCWL[CEPDF]) as the following equation:
qe_clk = (QE_CLK_IN × CEPMF) (1 + CEPDF) Eqn. 2
qe_clk = (QE_CLK_IN × CEPMF) (1 + CEPDF) Eqn. 3
For more information, see the QUICC Engine PLL Multiplication Factor section and the “QUICC Engine PLL Division Factor” section in the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual for more information.
The DDR SDRAM memory controller operates with a frequency equal to twice the frequency of csb_clk. Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider (2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate is the same frequency as ddr_clk.
The local bus memory controller operates with a frequency equal to the frequency of csb_clk. Note that lbc_clk is not the external local bus frequency; lbc_clk passes through the LBC clock divider to create the external local bus clock outputs (LCLK). The LBC clock divider ratio is controlled by LCRR[CLKDIV]. For more information, see the LBC Bus Clock and Clock Ratios section in the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
60 Freescale Semiconductor
Clocking
In addition, some of the internal units may be required to be shut off or operate at lower frequency than the csb_clk frequency. These units have a default clock ratio that can be configured by a memory mapped register after the device comes out of reset.
The following table specifies which units have a configurable clock frequency. For detailed description, refer to the “System Clock Control Register (SCCR)” section in the MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual.
NOTE
Setting the clock ratio of these units must be performed prior to any access to them.
The following table provides the maximum operating frequencies for the MPC8306 MAPBGA under recommended operating conditions (see Table 2).
22.2 System PLL Configuration
The system PLL is controlled by the RCWL[SPMF] parameter. Table 55 shows the multiplication factor encodings for the system PLL.
NOTE
System PLL VCO frequency = 2 × (CSB frequency) × (System PLL VCO divider). The VCO divider needs to be set properly so that the System PLL VCO frequency is in the range of 450–750 MHz.
As described in Section 22, “Clocking,” the LBCM, DDRCM, and SPMF parameters in the reset configuration word low select the ratio between the primary clock input (SYS_CLK_IN) and the internal
Table 53. Configurable Clock Units
Unit Default Frequency Options
I2C,SDHC, USB, DMA Complex csb_clk Off, csb_clk, csb_clk/2, csb_clk/3
Table 54. Operating Frequencies for MAPBGA
Characteristic1 Max Operating Frequency Unit
e300 core frequency (core_clk) 266 MHz
Coherent system bus frequency (csb_clk) 133 MHz
QUICC Engine frequency (qe_clk) 233 MHz
DDR2 memory bus frequency (MCLK)2 167 MHz
Local bus frequency (LCLKn)3 66 MHz
Notes:1. The SYS_CLK_IN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen such that the resulting
csb_clk, MCLK, LCLK, and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies.
2. The DDR2 data rate is 2× the DDR2 memory bus frequency.3. The local bus frequency is 1/2, 1/4, or 1/8 of the lb_clk frequency (depending on LCRR[CLKDIV]) which is in turn 1× or 2×
the csb_clk frequency (depending on RCWL[LBCM]).
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 61
Clocking
coherent system bus clock (csb_clk). The following table shows the expected frequency values for the CSB frequency for selected csb_clk to SYS_CLK_IN ratios.
22.3 Core PLL Configuration
RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300 core clock (core_clk). The following table shows the encodings for RCWL[COREPLL]. COREPLL values not listed, and should be considered reserved.
Table 55. System PLL Multiplication Factors
RCWL[SPMF] System PLL Multiplication Factor
0000 Reserved
0001 Reserved
0010 × 2
0011 × 3
0100 × 4
0101 × 5
0110 × 6
0111–1111 Reserved
Table 56. CSB Frequency Options
SPMF csb_clk : sys_clk_in Ratio
SYS_CLK_IN(MHz)
25 33.33 66.67
csb_clk Frequency (MHz)
0010 2:1 133
0011 3:1
0100 4:1 133
0101 5:1 125 167
0110 6:1
Table 57. e300 Core PLL Configuration
RCWL[COREPLL]core_clk : csb_clk Ratio VCO Divider
0-1 2-5 6
nn 0000 n PLL bypassed (PLL off, csb_clk clocks core directly)
PLL bypassed (PLL off, csb_clk clocks core directly)
00 0001 0 1:1 2
01 0001 0 1:1 4
10 0001 0 1:1 8
11 0001 0 1:1 8
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
62 Freescale Semiconductor
Clocking
NOTE
Core VCO frequency = core frequency VCO divider. The VCO divider (RCWL[COREPLL[0:1]]), must be set properly so that the core VCO frequency is in the range of 400–800 MHz.
22.4 QUICC Engine PLL Configuration
The QUICC Engine PLL is controlled by the RCWL[CEPMF] and RCWL[CEPDF] parameters. The following table shows the multiplication factor encodings for the QUICC Engine PLL.
00 0001 1 1.5:1 2
01 0001 1 1.5:1 4
10 0001 1 1.5:1 8
11 0001 1 1.5:1 8
00 0010 0 2:1 2
01 0010 0 2:1 4
10 0010 0 2:1 8
11 0010 0 2:1 8
00 0010 1 2.5:1 2
01 0010 1 2.5:1 4
10 0010 1 2.5:1 8
11 0010 1 2.5:1 8
00 0011 0 3:1 2
01 0011 0 3:1 4
10 0011 0 3:1 8
11 0011 0 3:1 8
Table 58. QUICC Engine PLL Multiplication Factors
RCWL[CEPMF] RCWL[CEPDF]QUICC Engine PLL Multiplication Factor = RCWL[CEPMF]/
(1 + RCWL[CEPDF)
00000–00001 0 Reserved
00010 0 2
00011 0 3
00100 0 4
00101 0 5
00110 0 6
Table 57. e300 Core PLL Configuration (continued)
RCWL[COREPLL]core_clk : csb_clk Ratio VCO Divider
0-1 2-5 6
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 63
Clocking
The RCWL[CEVCOD] denotes the QUICC Engine PLL VCO internal frequency as shown in the following table.
NOTE
The VCO divider (RCWL[CEVCOD]) must be set properly so that the QUICC Engine VCO frequency is in the range of 300–600 MHz. The QUICC Engine frequency is not restricted by the CSB and core frequencies. The CSB, core, and QUICC Engine frequencies should be selected according to the performance requirements.
The QUICC Engine VCO frequency is derived from the following equations:
qe_clk = (primary clock input × CEPMF) (1 + CEPDF)
QUICC Engine VCO Frequency = qe_clk × VCO divider × (1 + CEPDF)
22.5 Suggested PLL Configurations
To simplify the PLL configurations, the MPC8306 might be separated into two clock domains. The first domain contains the CSB PLL and the core PLL. The core PLL is connected serially to the CSB PLL, and has the csb_clk as its input clock. The second clock domain has the QUICC Engine PLL. The clock domains are independent, and each of their PLLs is configured separately.
The following table shows suggested PLL configurations for 33 and 66 MHz input clocks.
00111 0 7
01000 0 8
01001–11111 0 Reserved
Table 59. QUICC Engine PLL VCO Divider
RCWL[CEVCOD] VCO Divider
00 2
01 4
10 8
11 Reserved
Table 58. QUICC Engine PLL Multiplication Factors (continued)
RCWL[CEPMF] RCWL[CEPDF]QUICC Engine PLL Multiplication Factor = RCWL[CEPMF]/
(1 + RCWL[CEPDF)
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
64 Freescale Semiconductor
Clocking
Table 60. Suggested PLL Configurations
Conf No. SPMFCorePLL
CEPMF CEDFInput Clock Frequency
(MHz)
CSB Frequency
(MHz)
Core Frequency
(MHz)
QUICC
Engine Frequency
(MHz)
1 0100 0000100 0111 0 33.33 133.33 266.66 233
2 0010 0000100 0111 1 66.67 133.33 266.66 233
3 0100 0000101 0111 0 33.33 133.33 333.33 233
4 0101 0000101 1001 0 25 125 312.5 225
5 0010 0000101 0111 1 66.67 133.33 333.33 233
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 65
Thermal
23 ThermalThis section describes the thermal specifications of the MPC8306.
23.1 Thermal Characteristics
The following table provides the package thermal characteristics for the 369, 19 19 mm MAPBGA of the MPC8306.
23.1.1 Thermal Management Information
For the following sections, PD = (VDD IDD) + PI/O, where PI/O is the power dissipation of the I/O drivers.
23.1.2 Estimation of Junction Temperature with Junction-to-Ambient Thermal Resistance
An estimation of the chip junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RJA PD) Eqn. 1
where:
TJ = junction temperature (C)
Table 61. Package Thermal Characteristics for MAPBGA
Characteristic Board type Symbol Value Unit Notes
Junction-to-ambient natural convection Single-layer board (1s) RJA 39 °C/W 1, 2
Junction-to-ambient natural convection Four-layer board (2s2p) RJA 24 °C/W 1, 2, 3
Junction-to-ambient (@200 ft/min) Single-layer board (1s) RJMA 32 °C/W 1, 3
Junction-to-ambient (@200 ft/min) Four-layer board (2s2p) RJMA 21 °C/W 1, 3
Junction-to-board — RJB 14 °C/W 4
Junction-to-case — RJC 9 °C/W 5
Junction-to-package top Natural convection JT 2 °C/W 6
Notes:1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
2. Per JEDEC JESD51-2 with the single layer board horizontal. Board meets JESD51-9 specification.3. Per JEDEC JESD51-6 with the board horizontal.4. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method
1012.1).6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
66 Freescale Semiconductor
Thermal
TA = ambient temperature for the package (C)
RJA = junction-to-ambient thermal resistance (C/W)
PD = power dissipation in the package (W)
The junction-to-ambient thermal resistance is an industry standard value that provides a quick and easy estimation of thermal performance. As a general statement, the value obtained on a single layer board is appropriate for a tightly packed printed-circuit board. The value obtained on the board with the internal planes is usually appropriate if the board has low power dissipation and the components are well separated. Test cases have demonstrated that errors of a factor of two (in the quantity TJ – TA) are possible.
23.1.3 Estimation of Junction Temperature with Junction-to-Board Thermal Resistance
The thermal performance of a device cannot be adequately predicted from the junction-to-ambient thermal resistance. The thermal performance of any component is strongly dependent on the power dissipation of surrounding components. In addition, the ambient temperature varies widely within the application. For many natural convection and especially closed box applications, the board temperature at the perimeter (edge) of the package is approximately the same as the local air temperature near the device. Specifying the local ambient conditions explicitly as the board temperature provides a more precise description of the local ambient conditions that determine the temperature of the device.
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RJB PD) Eqn. 2
where:
TJ = junction temperature (C)
TB = board temperature at the package perimeter (C)
RJB = junction-to-board thermal resistance (C/W) per JESD51-8
PD = power dissipation in package (W)
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction temperature can be made. The application board should be similar to the thermal test condition: the component is soldered to a board with internal planes.
23.1.4 Experimental Determination of Junction Temperature
To determine the junction temperature of the device in the application after prototypes are available, the thermal characterization parameter (JT) can be used to determine the junction temperature with a measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (JT PD) Eqn. 3
where:
TJ = junction temperature (C)
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 67
Thermal
TT = thermocouple temperature on top of package (C)
JT = thermal characterization parameter (C/W)
PD = power dissipation in package (W)
The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire.
23.1.5 Heat Sinks and Junction-to-Case Thermal Resistance
In some application environments, a heat sink is required to provide the necessary thermal management of the device. When a heat sink is used, the thermal resistance is expressed as the sum of a junction-to-case thermal resistance and a case to ambient thermal resistance as shown in the following equation:
RJA = RJC + RCA Eqn. 4
where:
RJA = junction-to-ambient thermal resistance (C/W)
RJC = junction-to-case thermal resistance (C/W)
RCA = case-to-ambient thermal resistance (C/W)
RJC is device related and cannot be influenced by the user. The user controls the thermal environment to change the case-to-ambient thermal resistance, RCA. For instance, the user can change the size of the heat sink, the air flow around the device, the interface material, the mounting arrangement on printed-circuit board, or change the thermal dissipation on the printed-circuit board surrounding the device.
To illustrate the thermal performance of the devices with heat sinks, the thermal performance has been simulated with a few commercially available heat sinks. The heat sink choice is determined by the application environment (temperature, air flow, adjacent component power dissipation) and the physical space available. Because there is not a standard application environment, a standard heat sink is not required.
Accurate thermal design requires thermal modeling of the application environment using computational fluid dynamics software which can model both the conduction cooling and the convection cooling of the air moving through the application. Simplified thermal models of the packages can be assembled using the junction-to-case and junction-to-board thermal resistances listed in the thermal resistance table. More detailed thermal models can be made available on request.
23.2 Heat Sink Attachment
When attaching heat sinks to these devices, an interface material is required. The best method is to use thermal grease and a spring clip. The spring clip should connect to the printed-circuit board, either to the board itself, to hooks soldered to the board, or to a plastic stiffener. Avoid attachment forces which would lift the edge of the package or peel the package from the board. Such peeling forces reduce the solder joint
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
68 Freescale Semiconductor
System Design Information
lifetime of the package. Recommended maximum force on the top of the package is 10 lb (4.5 kg) force. If an adhesive attachment is planned, the adhesive should be intended for attachment to painted or plastic surfaces and its performance verified under the application requirements.
23.2.1 Experimental Determination of the Junction Temperature with a Heat Sink
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface between the case of the package and the interface material. A clearance slot or hole is normally required in the heat sink. Minimizing the size of the clearance is important to minimize the change in thermal performance caused by removing part of the thermal interface to the heat sink. Because of the experimental difficulties with this technique, many engineers measure the heat sink temperature and then back calculate the case temperature using a separate measurement of the thermal resistance of the interface.
From this case temperature, the junction temperature is determined from the junction-to-case thermal resistance using the following equation:
TJ = TC + (RJC PD) Eqn. 5
where:
TC = case temperature of the package (C)
RJC = junction-to-case thermal resistance (C/W)
PD = power dissipation (W)
24 System Design InformationThis section provides electrical and thermal design recommendations for successful application of the MPC8306.
24.1 System Clocking
The MPC8306 includes three PLLs.
• The system PLL (AVDD2) generates the system clock from the externally supplied SYS_CLK_IN input. The frequency ratio between the system and SYS_CLK_IN is selected using the system PLL ratio configuration bits as described in Section 22.2, “System PLL Configuration.”
• The e300 core PLL (AVDD3) generates the core clock as a slave to the system clock. The frequency ratio between the e300 core clock and the system clock is selected using the e300 PLL ratio configuration bits as described in Section 22.3, “Core PLL Configuration.”
• The QUICC Engine PLL (AVDD1) which uses the same reference as the system PLL. The QUICC Engine block generates or uses external sources for all required serial interface clocks.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 69
System Design Information
24.2 PLL Power Supply Filtering
Each of the PLLs listed above is provided with power through independent power supply pins. The voltage level at each AVDDn pin should always be equivalent to VDD, and preferably these voltages are derived directly from VDD through a low frequency filter scheme such as the following.
There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide independent filter circuits as illustrated in Figure 44, one to each of the three AVDD pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced.
This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum effective series inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor.
Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD pin, which is on the periphery of package, without the inductance of vias.
The following figure shows the PLL power supply filter circuit.
Figure 44. PLL Power Supply Filter Circuit
24.3 Decoupling Recommendations
Due to large address and data buses, and high operating frequencies, the MPC8306 can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8306 system, and MPC8306 itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, OVDD, and GVDD pins of the MPC8306. These decoupling capacitors should receive their power from separate VDD, OVDD, GVDD, and GND power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, OVDD, and GVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias
VDD AVDD
2.2 µF 2.2 µF
GNDLow ESL Surface Mount Capacitors (<0.5 nH)
10
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
70 Freescale Semiconductor
System Design Information
to minimize inductance. Suggested bulk capacitors—100 to 330 µF (AVX TPS tantalum or Sanyo OSCON).
24.4 Output Buffer DC Impedance
For all buses, the driver is a push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 45). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2.
Figure 45. Driver Impedance Measurement
The value of this resistance and the strength of the driver’s current source can be found by making two measurements. First, the output voltage is measured while driving logic 1 without an external differential termination resistor. The measured voltage is V1 = Rsource Isource. Second, the output voltage is measured while driving logic 1 with an external precision differential termination resistor of value Rterm. The measured voltage is V2 = (1/(1/R1 + 1/R2)) Isource. Solving for the output impedance gives Rsource = Rterm (V1/V2 – 1). The drive current is then Isource = V1/Rsource.
OVDD
OGND
RP
RN
PadData
SW1
SW2
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 71
Ordering Information
The following table summarizes the signal impedance targets. The driver impedance is targeted at minimum VDD, nominal OVDD, 105C.
24.5 Configuration Pin MultiplexingThe MPC8306 provides the user with power-on configuration options which can be set through the use of
external pull-up or pull-down resistors of 4.7 k on certain output pins (Refer to the “Reset, Clocking and Initialization” of MPC8306S PowerQUICC II Pro Integrated Communications Processor Family Reference Manual). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured.
25 Ordering InformationThis section presents ordering information for the devices discussed in this document, and it shows an example of how the parts are marked. Ordering information for the devices fully covered by this document is provided in Section 25.1, “Part Numbers Fully Addressed by This Document.”
25.1 Part Numbers Fully Addressed by This Document
The following table provides the Freescale part numbering nomenclature for the MPC8306 family. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Freescale sales office. In addition to the maximum processor core frequency, the part numbering scheme also includes the maximum effective DDR memory speed and QUICC Engine bus frequency. Each part number also contains a revision code which refers to the die mask revision number.
Table 62. Impedance Characteristics
ImpedanceLocal Bus, Ethernet, DUART, Control,
Configuration and Power ManagementDDR DRAM Symbol Unit
RN 42 Target 20 Target Z0 Ω
RP 42 Target 20 Target Z0 Ω
Differential NA NA ZDIFF Ω
Note: Nominal supply voltages. See Table 1, Tj = 105C.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
72 Freescale Semiconductor
Ordering Information
25.2 Part Marking
Parts are marked as in the example shown in the following figure.
Figure 46. Freescale Part Marking for MAPBGA Devices
The following table shows the SVR Settings.
Table 63. Part Numbering Nomenclature
MPC nnnn C VM AF D C A
ProductCode
PartIdentifier
Temperature Range1 Package2 e300 Core
Frequency3DDR2
Frequency
QUICC Engine
Frequency
Revision Level
MPC 8306 Blank = 0 to 105CC = –40 to 105C
VM = Pb-free AB = 133MHzAC = 200 MHzAD = 266 MHzAF = 333 MHz
D = 266 MHzF = 333 MHz
C = 233 MHz Contact local Freescale sales office
Notes: 1. Contact local Freescale office on availability of parts with C temperature range.2. See Section 21, “Package and Pin Listings,” for more information on available package types.3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this
specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other maximum core frequencies.
Table 64. SVR Settings
Device Package SVR (Rev 1.0) SVR (Rev 1.1)
MPC8306 MAPBGA 0x8110_0210 0x8110_0211
Note: PVR = 0x8085_0020
MPCnnnnetppaaar
core/platform MHZ
ATWLYYWW
CCCCC
MAPBGA
*MMMMM YWWLAZ
Notes:ATWLYYWW is the traceability code.CCCCC is the country code.MMMMM is the mask number.YWWLAZ is the assembly traceability code.
Downloaded from Elcodis.com electronic components distributor
MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 2
Freescale Semiconductor 73
Document Revision History
26 Document Revision HistoryThe following table provides a revision history for this document.
Table 65. Document Revision History
Rev. No.
Date Substantive Change(s)
2 09/2011 • Added Power numbers for core frequency of 333 MHz in Table 5. • Added new PLL configurations as per new core frequency in Table 60. • Added AF to indicate 333 MHz in Table 63.
1 06/2011 • Updated QE frequency in Table 5. • Updated QUICC Engine frequency from 200 MHz to 233 MHz in Table 54. • Updated CEMF and CEDF as per new QE frequency in Table 60. • In Part Nomenclature field for QUICC Engine frequency, C now denotes 233 MHz. Updated Table 63. • Added SPISEL_BOOT in MPC8306 Pin out Listing Table 52. • Corrected SPISEL Pin Type in Table 52.
0 03/2011 Initial Release
Downloaded from Elcodis.com electronic components distributor
Document Number: MPC8306ECRev. 209/2011
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals” must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
How to Reach Us:
Home Page: www.freescale.com
Web Support: http://www.freescale.com/support
USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc.Technical Information Center, EL5162100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or+1-480-768-2130www.freescale.com/support
Europe, Middle East, and Africa:Freescale Halbleiter Deutschland GmbHTechnical Information CenterSchatzbogen 781829 Muenchen, Germany+44 1296 380 456 (English) +46 8 52200080 (English)+49 89 92103 559 (German)+33 1 69 35 48 48 (French) www.freescale.com/support
Japan: Freescale Semiconductor Japan Ltd. HeadquartersARCO Tower 15F1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064Japan 0120 191014 or+81 3 5437 [email protected]
Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23FNo. 118 Jianguo RoadChaoyang DistrictBeijing 100022China+86 10 5879 [email protected]
For Literature Requests Only:Freescale Semiconductor
Literature Distribution Center 1-800 441-2447 or+1-303-675-2140Fax: +1-303-675-2150LDCForFreescaleSemiconductor
@hibbertgroup.com
Freescale, the Freescale logo, CodeWarrior, ColdFire, PowerQUICC, StarCore, and Symphony are trademarks of Freescale Semiconductor, Inc. Reg. U.S. Pat. & Tm. Off. CoreNet, QorIQ, QUICC Engine, and VortiQa are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. 802.3 and
1149.1 are registered trademarks of the Institute of Electrical and Electronics Engineers, Inc. (IEEE).
© 2011 Freescale Semiconductor, Inc.
Downloaded from Elcodis.com electronic components distributor