mp6000/mp7000 technical accessory guide - boreal technologies · 2019. 2. 21. · tower usb cable...
TRANSCRIPT
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 1 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
MP6000/MP7000 Technical Accessory Guide
Part Number Picture Description Notes
CBA-U51-S16ZAR USB Cable: Series A Connector, 5 meter Straight
Part Number Picture Description Notes
CBA-U52-S16PAR USB Cable: Power Plus Connector, 5 meter Straight Power is provided from POS
Part Number Picture Description Notes
CBA-R51-S16ZARRS232 Cable:STD-DB9 Female, TxD on 2, 5 meter Straight
Also used to connect scale to POS (Dual Cable Scanner/Scale)
CBA-R52-S16ZAR RS232 Cable:STD-DB9 Male, TxD on 2, 5 meter Straight
Also used to connect scale to POS (Dual Cable Scanner/Scale)
Part Number Picture Description Notes
CBA-R53-S16ZAR Serial Nixdorf DB9-Female, 5 meter Straight Cable ►Discontinued 4/2018 - PMB 3047.
Part Number Picture Description Notes
CBA-R53-S16PARRS232 Cable: DB15 TxD on 4, Power on 1, 5 meter Straight
Provides power to MP6000/MP7000
Part Number Picture Description Notes
CBA-M51-S16PAR IBM 468x/9x, Port 9B Cable, 5 meter Straight
►RS485 interface cable►Provides power to MP6000/MP7000
►Power Supply (PWR-BGA12V50W0WW and CBL-DC-375A1-01)►AC Line Cord (23844-00-00R) to power MP6000/MP7000
IBM POS USB Cables
NOTE: This document is only for general reference. Solution Builder and related PMBs should be used for product availability, pricing, and final solution selection.
Communication Cables
Zebra associates and partners can also see Zebra's Universal Cable Guide at: https://partnerportal.zebra.com/PartnerPortal/product_services/downloads_z/barcode_scanners/Universal-Cable-Guide-Bar-Code-Scanners.xlsx
Standard USB Cables
Required Items
►Power Supply (PWR-BGA12V50W0WW and CBL-DC-375A1-01) ►AC Line Cord (23844-00-00R)
RS232 CablesRequired Items
►Power Supply (PWR-BGA12V50W0WW and CBL-DC-375A1-01)►AC Line Cord (23844-00-00R) to power MP6000/MP7000
Required Items
* Zebra does not endorse or specifically recommend any third-party products, accessories, or hardware . ZEBRA DISCLAIMS ANY AND ALL LIABILITY, INCLUDING ANY EXPRESS OR IMPLIED WARRANTIES, WHETHER ORAL OR WRITTEN, FOR SUCH THIRD PARTY PRODUCTS, ACCESSORIES, OR HARDWARE. THE CUSTOMER ACKNOWLEDGES THAT NO REPRESENTATION HAS BEEN MADE BY ZEBRA AS TO THE FITNESS OF THE THIRD-PARTY PRODUCTS, ACCESSORIES, OR HARDWARE FOR THE CUSTOMER'S INTENDED PURPOSE.
IBM 468x/469x POS Cables
Required Items
Auxillary Cables
NOTE: MP6000 discontinued 1/2018 - see PMB 3036
Siemens Nixdorf Beetle POS Terminal RS232 Cables
Required Items
►Power Supply (PWR-BGA12V50W0WW and CBL-DC-375A1-01)►AC Line Cord (23844-00-00R)
Other POS Terminal RS232 Cables
Required Items
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 2 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
CBA-A51-S16ZAR Auxillary Scanner Cable, RS232 Serial
►Allows handheld scanners (i.e. LI4278, LS4278, or DS6878) to be used with MP6000/MP7000 for scanning heavy/awkward items.►5 meter length►RS232 serial connection to scanner►Connects to AUX2 port on MP6000/MP7000►Provides power to corded scanners►NOTE: MP6000/MP7000 supports maximum of 2 auxillary scanners.
VariousAuxillary Scanner Cable, USB
►Refer to accessory document for handheld scanner for USB cable choice.►Allows handheld scanners (i.e. LI4278, LS4278, or DS6878) to be used with MP6000/MP7000 for scanning heavy/awkward items.►USB connection to scanner►Connects to AUX A-B port on MP6000►Provides 5V power to scanners►NOTE: MP6000/MP7000 supports maximum of 2 auxillary scanners.
Part Number Picture Description Notes
MX101-SR7000WW Customer Side Scanner (CSS) for MP7000
►Allows customers to simultaneously scan their own loyalty cards, coupons, impulse buy items and bar codes displayed on their mobile phones►Uses SE3317 scan engine►Includes Top Cover, scan engine, and USB cable. Connect USB cable to top port on MP7000 AUX A-B USB ports.►Only compatible with MP7000.
MX101-SR00004ZZWR Customer Side Scanner (CSS) for MP6000
►Discontinued 1/2018 - PMB 3036►Allows customers to simultaneously scan their own loyalty cards, coupons, impulse buy items and bar codes displayed on their mobile phones►Uses SE3317 scan engine►Includes Top Cover, scan engine, and USB cable. Connect USB cable to top port on MP6000 AUX A-B USB ports.►Only compatible with MP6000.
MX201-SI00WWScale Display with Pole (Single display) - Pounds or KG - Single Interval
►Single Display Head: Clear, easy to adjust weight display.►Includes scale display templates/overlays for single interval LB, and single interval KG.►Single Interval is the most common scale display requirement (used in US) and is used with Single Interval scale configurations of the MP series. Dual Interval (MX201-DI00WW) may be required in other countries (i.e. Russia).►Display connects to 0.0 port on MP6000/MP7000.►Has a slightly smaller footprint than MX201-SR00004ZZWR/MX201-SR00004ZZRR which allows foreasier installation.
Keyboard Wedge Cables (Not supported by MP6000/MP7000)
NOTE: If cradle is used with a cordless scanner, it must be powered using an external power supply.
Synapse Adapter Cables (Not supported by MP6000/MP7000)
Misc
Required Items
Wand Cables (Not supported by MP6000/MP7000)
3 - 16 MP6000 INTEGRATOR GUIDE
Install the Customer Side Scanner (MX101)
The MX101 is an optional modular unit that fits into a modified MP6000 tower and is used for customer scanning. The unit can be installed on either the left or right side of the MP6000.
Remove all hardware from the packaging. The packaging contains the MX101 scan module and window; MP6000 modified rear tower; USB cable; and MX101 identification label (Regulatory Guide; instructions to affix the label on the MP6000; and installation instructions not shown).
Scan Module and Window
Tower
USB Cable
Identification Label
Figure 3-14 Parts of the MX101
3 - 16 MP6000 INTEGRATOR GUIDE
Install the Customer Side Scanner (MX101)
The MX101 is an optional modular unit that fits into a modified MP6000 tower and is used for customer scanning. The unit can be installed on either the left or right side of the MP6000.
Remove all hardware from the packaging. The packaging contains the MX101 scan module and window; MP6000 modified rear tower; USB cable; and MX101 identification label (Regulatory Guide; instructions to affix the label on the MP6000; and installation instructions not shown).
Scan Module and Window
Tower
USB Cable
Identification Label
Figure 3-14 Parts of the MX101
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 3 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
MX201-SR00004ZZWRScale Display with Pole (Single display) - Pounds only
►Discontinued 12/2016, now use MX201-SI00WW - see PMB 2917►Single Display Head: Clear, easy to adjust weight display for pounds only scale models.►Includes scale display template/overlay for single interval LB►Display connects to 0.0 port on MP6000/MP7000.
MX201-DI00WWScale Display with Pole (Single display) - Pounds or KG - Dual Interval
►Single Display Head: Clear, easy to adjust weight display.►Includes scale display templates/overlays for dual interval LB and and dual interval KG.►Dual Interval is not a common display configuration. It may only be required in certain countries (i.e. Russia) and is used with Dual Interval scale configurations of the MP series.. Use Single Interval configuration (MX201-SI00WW) in most countries (including US). ►Display connects to 0.0 port on MP6000/MP7000.►Has a slightly smaller footprint than MX201-SR00004ZZWR/MX201-SR00004ZZRR which allows foreasier installation.
MX201-MODScale Display with Pole (Single display) - Pounds only - Modified Hole Pattern
►To be discontinued 2/2019 - see PMB 10043►Uses different hole pattern than MX201-SR00004ZZWR►Single Display Head: Clear, easy to adjust weight display for pounds only scale models.►Includes scale display template/overlay for single interval LB►Display connects to 0.0 port on MP6000/MP7000.
MX201-SR00004ZZWWScale Display with Pole (Single display) - Pounds or KG
►Discontinued 12/2016, now use MX201-SI00WW - see PMB 2917►Single Display Head: Clear, easy to adjust weight display.►Includes scale display templates/overlays for single interval LB, dual interval LB, single interval KG, and dual interval KG►Display connects to 0.0 port on MP6000/MP7000.
MX202-SI00WWScale Display with Pole (Dual display) - Pounds or KG - Single Interval
►Dual Display Heads: Clear, easy to adjust weight display.►Dual-heads are used where the law is strictest on visibility of the weight value for cashier and customer. Design fully rotates both heads independently, offering maximum flexibility and visibility. Competing designs have heads whose rotation interferes with each other, limiting the choice for direction of display.►Includes scale display templates/overlays for single interval LB, and single interval KG.►Single Interval is the most common scale display requirement (used in US) and is used with Single Interval scale configurations of the MP series. Dual Interval (MX202-DI00WW) may be required in other countries (i.e. Russia).►Display connects to 0.0 port on MP6000/MP7000.
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 4 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
MX202-DI00WWScale Display with Pole (Dual display) - Pounds or KG - Dual Interval
►Dual Display Heads: Clear, easy to adjust weight display.►Dual-heads are used where the law is strictest on visibility of the weight value for cashier and customer. Design fully rotates both heads independently, offering maximum flexibility and visibility. Competing designs have heads whose rotation interferes with each other, limiting the choice for direction of display.►Includes scale display templates/overlays for dual interval LB, and dual interval KG.►Dual Interval is not a common display configuration. It may only be required in certain countries (i.e. Russia) and is used with Dual Interval scale configurations of the MP series. Use Single Interval configuration (MX202-SI00WW) in most countries (including US). ►Display connects to 0.0 port on MP6000/MP7000.
MX202-SR00004ZZWR Additional Scale Display
►Discontinued 6/2017, now use MX202-SI00WW or MX202-DI00WW in some locals (PMB 2976)►Additional display head to convert Single Display displays to a dual-head, easy to adjust weight display for scale models. Fully independent swivel for superb cashier and customer readability.►Attaches to top of Scale Display with Pole (MX201)►Includes scale display templates/overlays for single interval LB, dual interval LB, single interval KG, and dual interval KG
MX201-POLE-EXT Scale Display Extension Pole
►Compatible with Scale Display with Pole (Single display) - (MX201-SI00WW)►Extends length of scale display pole by 24 inches.►Includes pipe flange for mounting pole on countertop and 4 screws
MX201-EXT Scale Display Extension Pole
►To be discontinued 5/2019 - see PMB 10111►Extends length of scale display pole by 24 inches.►Includes pipe flange for mounting pole on countertop and 4 screws
CBA-A54-S01EAR Checkpoint Interlock Cable
►Allows MP6000/MP7000 to send good barcode scan message to Checkpoint system for EAS tag deactivation in parallel to scanning the barcode on the product►Cable connects to Checkpoint Interlock Port on MP6000/MP7000.►Requires proper integration with Checkpoint EAS sytem by Checkpoint personnel.
Scale Display with Pole (Single display) - (MX201)
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 5 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
MX306-SA00WW Checkpoint Antenna - Horizontal
►Antenna used to de-activate Checkpoint Electronic Article Surveillance (EAS) Systems.►Only compatible with MP7000.
MX307-SA00WW Checkpoint Antenna - Vertical
►Antenna used to de-activate Checkpoint Electronic Article Surveillance (EAS) Systems.►Only compatible with MP7000.
MX303-SB-05 Width Extender (trim piece) for MP7000
►Used with M7000 Long models to fit into a counter cut-out previously occupied by a 12 in. wide NCR scanner/scale. ►The trim can be mounted on either side of the MP7000. It should be installed in the downstream side of the conveying goods. ►Adds 0.5 in. (1.2 cm) to the width of the MP7000.►Includes 4 screws for attaching Extender
MX303-SR00004ZZWR Width Extender (trim piece) for MP6000
►Discontinued 1/2018 - PMB 3036►Used with MP6000 Long models to fit into a counter cut-out previously occupied by a 12 in. wide NCR scanner/scale. ►The trim can be mounted on either side of the MP6000. It should be installed in the downstream side of the conveying goods. ►Adds 0.5 in. (1.2 cm) to the width of the MP6000.►Includes 4 screws for attaching Extender
MX304-SR00004ZZWR Extension Bracket for MP6000
►Discontinued 1/2018 - PMB 3036►Extends length of MP6000 Medium unit from 15.7" to 16.5” (41.91cm)
3 - 38 MP6000 INTEGRATOR GUIDE
Trim Kit Installation (If Required)
The MX303-SR00004ZZWR trim kit can be used to modify the long MP6000/scale to fit into a counter cut-out previously occupied by a 12 in. wide NCR scanner/scale. The trim can be mounted on either side of the MP6000. It should be installed in the downstream side of the conveying goods. The trim adds 0.5 in. (1.2 cm) to the width of the MP6000.
The kit includes one metal trim, and two Phillips head screws (M4 x 8mm).
To install the trim:
1. Insert the two screws provided in the rail.
2. Orient the adapter as shown in the illustration.
Figure 3-48 Orient the Adapter
3. Attach the side rail to the MP6000, and tighten using a Phillips head screwdriver.
Figure 3-49 Attach the Adapter
MN000771A02 Revision B - January 2015
Zebra Technologies Corporation, Lincolnshire, IL U.S.A., http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademarkof Symbol Technologies, Inc., a Zebra Technologies company© 2015 Symbol Technologies, Inc.
1 2
3
MP6000 MOUNTING FRAMEINSTALLATION INSTRUCTIONS
A
21
34
56
78 8
76
54
31
2
B C D E F G H
A B C D E F G H
Zebra_U
S_D
Sheet: 1 O
F 2
Model Name: MX306_MP7_XPOINT_ASSY :: &PTC_WM_VERSION:mdl
Drawing Name: MX306_MP7_XPOINT_ASSY :: 1.1S
cale: 2.00
Revision
1MX306-SA00W
WSize
D Assy: Checkpoint Antenna, MP7000MP7000
DO
NO
T SCA
LED
RA
WIN
GVIEW
PROJECTION
TO
LER
AN
CE
S U
NLE
SS
OT
HE
RW
ISE
SP
EC
IFIE
D
X.=
1 .X
=0.25
.XX
=0.13
AN
GLE
S=
0.5
Feb-22-2017Potter, Jason
CO
NFID
ENTIA
L AN
D PR
OPR
IETAR
Y THE INFORMATION CONTAINED HEREIN IS THE CONFIDENTIAL AND THE EXCLUSIVE PROPERTY OF ZIH CORP. THIS DOCUMENT, AND THE INFORMATION CONTAINED HEREIN, SHALL NOT BE COPIED, REPRODUCED, PUBLISHED, DISPLAYEDOR DISTRIBUTED, IN W
HOLE OR IN PART, IN ANY MEDIUM, BY ANY MEANS, FOR ANY PURPOSE W
ITHOUT THE EXPRESS W
RITTEN CONSENT OF ZIH CORP. © ZIH CORP. 2015 ALL RIGHTS RESERVED
Create D
ateC
reated By
N/AS
pecifications
N/AF
inish / Color
INT
ER
PR
ET
PE
R
ASME Y14.5M-1994N/A
RoH
S CO
MPLIA
NC
E THIS PART/ASSEMBLY TO COMPLY W
ITH ZEBRA TECHNOLOGIES MATERIAL CONTENT POLICY NUMBER CPZ-CE-003. ANY MATERIALOR PROCESS CHANGE AFFECTING COMPLIANCE W
ITH THISPOLICY MUST BE COMMUNICATED TO AND APPROVED BYZEBRA TECHNOLOGIES PRIOR TO MAKING THE ACTUAL CHANGE.
Material
DIM
EN
SIO
NS
AR
E IN
Metric (m
m)
ENCIRCLED DIMENSIONS AND GD&T INDICATE CRITICAL-TO-FUNCTION FEATURES
RE
VIS
ED
BY
EC
O N
UM
BE
RR
EV
DA
TE
RE
VIS
ION
Potter, JasonEC-11669
Feb-24-20171
INIT
IAL R
ELE
AS
E--
NO
TE
S: U
NLE
SS
OT
HE
RW
ISE
SP
EC
IFIE
D 1. A
SS
EM
BLE
AS
FO
LLOW
S:
1. INS
ER
T T
IP O
F W
IRE
INT
O T
RA
CK
AT
MA
RK
ED
LOC
AT
ION
2. FE
ED
WIR
E LO
OP
INT
O T
RA
CK
FR
OM
INS
ER
TIO
N P
OIN
T T
O T
AIL E
ND
. W
IRE
MU
ST
GO
BE
LOW
ALL H
OO
KS
. 3. F
ULLY
INS
ER
T W
IRE
INT
O T
RA
CK
US
ING
A B
LAC
K S
TIC
K.
SE
E S
HE
ET
2 FO
R A
DD
ITIO
NA
L AS
SE
MB
LY D
ET
AILS
. 2. P
AR
TS
MU
ST
BE
FR
EE
OF
FO
RE
IGN
PA
RT
ICLE
S A
ND
CO
NT
AM
INA
NT
S.
3. WO
RK
MA
NS
HIP
PE
R Z
EB
RA
SP
EC
IFIC
AT
ION
SS
-03800-57-08 CA
TE
GO
RY
A.
4. PA
CK
AG
E IT
EM
S IN
AC
CO
RD
AN
CE
WIT
H Z
EB
RA
GE
NE
RA
L PA
CK
AG
ING
SP
EC
IFIC
AT
ION
50-04100-013. 5. S
EE
ZE
BR
A S
PE
CIF
ICA
TIO
N S
P-12509-01 F
OR
MA
ND
AT
OR
Y R
EQ
UIR
EM
EN
TS
RE
GA
RD
ING
EN
VIR
ON
ME
NT
AL C
OM
PLIA
NC
E (IN
CLU
DIN
G B
UT
NO
T LIM
ITE
D T
O R
oHS
).
12345
3 - 38 MP6000 INTEGRATOR GUIDE
Trim Kit Installation (If Required)
The MX303-SR00004ZZWR trim kit can be used to modify the long MP6000/scale to fit into a counter cut-out previously occupied by a 12 in. wide NCR scanner/scale. The trim can be mounted on either side of the MP6000. It should be installed in the downstream side of the conveying goods. The trim adds 0.5 in. (1.2 cm) to the width of the MP6000.
The kit includes one metal trim, and two Phillips head screws (M4 x 8mm).
To install the trim:
1. Insert the two screws provided in the rail.
2. Orient the adapter as shown in the illustration.
Figure 3-48 Orient the Adapter
3. Attach the side rail to the MP6000, and tighten using a Phillips head screwdriver.
Figure 3-49 Attach the Adapter
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 6 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
MX305-SR00004ZZWR Tower Extender
►To be discontinued 2/2019 - see PMB 10043►Extends height of MP6000/MP7000 from 5.1 inches to 7 inches►Attaches to Top Cover
MX301-SR00004ZZWR Leveling Screws - Standard length, pack of 4
►NOTE: These screws are already included with each Short or Medium size MP7000 unit.►Used with Short and Medium size MP6000/MP7000 units. ►Long versions do not support leveling screws. The checkstand should provide for two leveling screws under the front and rear of the MP6000/MP7000.►M8 x 50 mm size►Allows fine adjustment of short and medium model MP6000/MP7000 scanners so they are perfectly flush in the checkstand
MX302-SR00004ZZWR Leveling Screws - Extended length, pack of 4
►M8 x 70 mm size►Used with Short and Medium size MP6000/MP7000 units.►Long versions do not support leveling screws. The checkstand should provide for two leveling screws under the front and rear of the MP6000/MP7000.►The MP6000/MP7000 is 4 in. deep. If replacing a pre-existing 5 in. deep short or medium scanner, these screws will bring the platter up to the countertop level.►Allows fine adjustment of short and medium model MP6000/MP7000 scanners so they are perfectly flush in the checkstand, while matching the 12.5cm / 5" depth of some older laser bioptic scanners►Extended length screws which will protrude 1"-inch (25 mm) below the bottom of the unit.
Part Number Picture Description Notes
CBL-DC-388A1-01 DC Power Cord for MP7000
►Used along with Power Supply PWR-BGA12V50W0WW to power MP7000. Can also be used with MP6000, but CBL-DC-375A1-01 is the preferred cable for MP6000.►Cable length is 1.8 meters
CBL-DC-375A1-01 DC Power Cord for MP6000►Used along with Power Supply PWR-BGA12V50W0WW to power MP6000.►Cable length is 1.5 meters
PWR-BGA12V50W0WW Power Supply
►100-240 VAC,12V, 4.16A, 50W ►Provides US DOE Level VI compliance for power efficiency.►Replaces PWRS-14000-148R
Power Supplies/Power Cords
Required Items
►DC Line Cord (CBL-DC-375A1-01) for MP6000 OR DC Line Cord (CBL-DC-388A1-01) for MP7000►AC Line Cord (23844-00-00R)
Optional Scale (scale is not available in MP6000 short models)
Staging USB Flash Drive Cap/Port
PRODUCT OVERVIEW AND FEATURES 1 - 11
Figure 1-4 View Under Platter
Figure 1-5 Leveling Screws4 Leveling Screws (2 screws on opposite side) 1
Leveling Screw Access Holes(medium and short units only)
NOTE The tower bezel must be removed, and the Tower Cover slid backwards to access the leveling screws. 1 Leveling screws are an optional accessory. To use leveling screws, buy accessory kit MX301-SR00004ZZWR for standard-length screws, or accessory kit MX302-SR00004ZZWR for 1 in. (25 mm) extra length.
Optional Scale (scale is not available in MP6000 short models)
Staging USB Flash Drive Cap/Port
PRODUCT OVERVIEW AND FEATURES 1 - 11
Figure 1-4 View Under Platter
Figure 1-5 Leveling Screws4 Leveling Screws (2 screws on opposite side) 1
Leveling Screw Access Holes(medium and short units only)
NOTE The tower bezel must be removed, and the Tower Cover slid backwards to access the leveling screws. 1 Leveling screws are an optional accessory. To use leveling screws, buy accessory kit MX301-SR00004ZZWR for standard-length screws, or accessory kit MX302-SR00004ZZWR for 1 in. (25 mm) extra length.
* UNLESS OTHERWISE SPECIFIED *
DIMENSIONS ARE IN MILLIMETERS
DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
UNTOLERANCED DIMENSIONS ARE BASIC
8 7 6 5 4 3 2 1
A
B
C
D
D1B (12/10)
8 7 6 5 4 3 2 1
A
B
C
D
VIEWS SHOWN IN
THIRD ANGLE PROJECTION
COMPUTER GENERATED DRAWING
DO NOT SCALE
INFORMATION CONTAINED ON ALL SHEETS OF THIS PRINT
CANNOT BE REPRODUCED OR USED, IN WHOLE OR IN PART,
WITHOUT MOTOROLA SOLUTIONS INC. CONSENT.
THIS NOTICE DOES NOT IMPLY PUBLICATION
MOTOROLA SOLUTIONS INC.
PROPRIETARY AND CONFIDENTIAL
One Motorola Plaza,
Holtsville, NY 11742
MOTOROLA SOLUTIONS INC.
23.36
217.62
2X THRU
ITEM 10 ONLY
4.50 0.10
1
2
3
4
5
6
8-11
7
SCALE 1/2
B
C
A
C
2X 37.07
REVISIONS
REV ZONE DESCRIPTION E.C. BY APVD. DATE
A RELEASED PER EC 78949 CT AN 4/18/14
SCALE: 1/1 SOLID MODEL
YES NO
XSHEET 1 OF 1
SIZE DWG. NO. REV
D HN000268G A
ASSY: TOWER EXTENDER
MP6000
APPROVALS DATE
DRAWN
C.TUNJIAN 3/4/14
CHECKED
J.GIORDANO 3/4/14
ENGINEER
A.NANEY 3/4/14
ANALYST
MFG.ENG.
PRODUCT
QUALITY
0.25 A B C
COPYRIGHT 2014 MOTOROLA SOLUTIONS INC.
NOTES: UNLESS OTHERWISE SPECIFIED NOTES:
1. TORQUE SPECIFICATION: ITEM 13 (SCREWS) TO BE TORQUED TO: 12.00 �#�0.25 IN-LBS
2. ADHERE ITEM 12 (PSA) TO ITEM 11 (EXTENDER: TOWER). ITEM 11 AND 12 (EXTENDER: TOWER AND PSA)
TP BE ASSEMBLED TO ITEM 10 (ASSEMBLY: BEZEL, TOWER) USING A FIXTURE.
3. PSA AREAS MUST BE CLEAN PRIOR TO ADHERING PSA. CLEAN HOUSING WITH A 50/50
MIXTURE OF ISOPROPYL ALCOHOL AND WATER PRIOR TO ADHERING PSA.
4. NUMBERS IN ARE FOR INSPECTION USE ONLY. LAST NUMBER USED = 11.
5. ITEMS 8 THROUGH 11 TO BE INSPECTED ON THE FIXTURE FOR P/N: 11-161193-07
6. PACKAGE ITEMS IN ACCORDANCE WITH MOTOROLA GENERAL PACKAGING SPECIFICATION 35:50-04100-013.
7. SEE MOTOROLA SPECIFICATION SP-12509-01 FOR MANDATORY REQUIREMENTS REGARDING
ENVIRONMENTAL COMPLIANCE (INCLUDING BUT NOT LIMITED TO RoHS).
4X
SEE NOTE 2
SEE ASSOCIATED BOM HN000268G07
AND SUBSEQUENT BOM'S
10
13 2X
SEE NOTE 1
11
12BEZEL HOLE DETAIL
DCS Product Line - MP6000/MP7000 TAG
NOTE: Items highlighted in grey may not be orderable/available
Page 7 of 7
Changes?/Updates? - notify [email protected] Document Update date: 1/18/19
KIT-PWR-12V50W Power Supply Kit for MP7000
►Includes Power Supply (PWR-BGA12V50W0WW) and DC Line Cord (CBL-DC-388A1-01)►Used to power MP7000. Can also be used with MP6000, but CBL-DC-375A1-01and BGA12V50W0WW is the preferred cable and power supply for MP6000.
PWRS-14000-148R Power Supply with integrated DC Cord
►Discontinued 1/2017, now use PWR-BGA12V50W0WW and CBL-DC-375A1-01 - see PMB 2903.►Replaces KT-14000-148R ►100-240 VAC,12VDC,3.33A ►Energy Star Compliant
50-14000-148R Power Supply with integrated DC Cord
►Discontinued 12/2007 - replaced by KT-14000-148R
KT-14000-148R Power Supply with integrated DC Cord
►Replaces 50-14000-148R ►Discontinued 12/2010 - now use PWRS-14000-148R
23844-00-00R AC Line Cord
AC Line Cord (23844-00-00R)
AC Line Cord (23844-00-00R)
AC Line Cord (23844-00-00R)
AC Line Cord (23844-00-00R)