mortise lock installation instructions - assa abloy · 2017. 6. 15. · 8 79-0035 lock front - 7900...

A8204B 04/16

Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

PoE Mortise LockInstallation Instructions

IN220

1-800-810-WIRE • www.sargentlock.com • A8204B

Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/

161

2

3

4

5

6

7

Table of ContentsWarning ...................................................................................3General Description .................................................................4Specifications ..........................................................................4System Overview .....................................................................4Parts Breakdown .....................................................................5Installation Wiring ...................................................................7Lock Installation ....................................................................11Operational Check ................................................................25

Changes or modifications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment.

Warning 1FCC:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada:This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

!

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation

• Do not touch pins, leads or solder connections on the circuit boards

8

4 1-800-810-WIRE • www.sargentlock.com • A8204B

Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/

16IN220 Mortise Lock

General Description2

Hardware Specifications3• Complete lockset with on-board memory

• ADA compliant

• Easily retrofits existing door preps (mortise)

• Latch - Stainless steel

• Optional deadbolt - Hardened steel

• Guardbolt - Stainless steel, non handed

• Handing (RH/RHR/LH/LHR) must be specified, but is easily field-reversible without opening lock case

• Case - 12 gauge heavy duty wrought steel

• Cylinder retracts latchbolt (and deadbolt)

• Lock furnished for 1-3/4” doors. For other thicknesses, consult factory.

• Outside lever controlled by any combination of contactless reader or mechanical cylinder

• Inside lever retracts both latch and deadbolt

• May be used for indoor and outdoor applications

• ANSI/BHMA A156.25 Listed Grade 1 Compliant

*UL testing was conducted on product powered by UL Listed model 9001GR/AC injector; manufactured by Microsemi Corp.

Electronic Specifications4• Input Power: PoE Class 1 Device, as defined by

IEEE 802.3af, requires less than to 3.84 watts over structured cabling

• Multiple time zone and holiday access scheduling

• First-in unlock or automatic unlock configuration based on specified time schedule

• 2,400 users per lock; 10,000 event audit trail

• Power Requirements: 55VDC, 90mA

• Privacy button

• HID® multiCLASS SE® technology offers support for the following credentials:• 2.4 GHz credential compatibility:

• 125 kHz credential compatibilty:• HID Prox®

• 13.56 MHz credential compatibility:• iCLASS® • iCLASS SE® (SIO-enabled)• iCLASS Seos®

• SIO on MIFARE® Classic• SIO on MIFARE® DESfire® EV1• MIFARE® Classic• DESfire® EV1• NFC-enabled mobile phones

• Secure Identity Object™ (SIO) on Mobile IDs (Bluetooth Smart)

• UL 294 Access Control Ratings:

Destructive Attack Level 1

Line Security Level 1

Endurance Level 4

Standby Power Level 1

• UL Listed* - UL 294 Indoor Use

• CUL Listed - S319: Class 1

The SARGENT IN220 Mortise lock combines superior aesthetics with the energy efficiency and streamlined architecture of Power-over-Ethernet (PoE) access control. PoE-enabled access control allows facilities to leverage existing network infrastructure for enhanced security and easier, more cost-effective installations. Featuring multiCLASS SE® technology, it supports multiple credential types, including mobile devices, for a future-proof solution that is convenient and secure.

NOTE: A weather-protective gasket is required for outdoor applications.

04/3

0/16

1-800-810-WIRE • www.sargentlock.com • A8204B 5

Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

Parts Breakdown5

1*

4

3

2

2a

** Specify finish

*Specifying B indicates Bluetooth® Smart option when ordering

1 IN-220-EM01-[B*]IP-B Reader assembly - black plastic 1

IN-220-EM01-[B*]IP-W Reader assembly - white plastic

IN-220-EM01-[B*]IP-MB-xxx** Reader assembly - black plastic with metal trim

IN-220-EM01-[B*]IP-MW-xxx** Reader assembly - white plastic with metal trim

IN-220-EM01-[B*]IPS-B Reader assembly - black plastic

IN-220-EM01-[B*]IPS-W Reader assembly - white plastic

IN-220-EM01-[B*]CP-B Reader assembly - FeliCa - black plastic

IN-220-EM01-[B*]CP-W Reader assembly - FeliCa - white plastic

IN-220-EM01-[B*]CP-MB-xxx** Reader assembly - FeliCa - black plastic with metal trim

IN-220-EM01-[B*]CP-MW-xxx** Reader assembly - FeliCa - white plastic with metal trim

IN-220-EM01-[B*]IPS-MB-xxx** Reader assembly - black plastic with metal trim

IN-220-EM01-[B*]IPS-MW-xxx** Reader assembly - white plastic with metal trim

2 IN-220-EM04 Mounting plate assembly 1

2a Through-bolts (#8-32 x 1 1/4”) 2

3 IN-220-EM03 Controller assembly 1

4 IN-220-EM02-B Inside cover assembly - black plastic 1

IN-220-EM02-W Inside cover assembly - white plastic

IN-220-EM02-MB-xxx** Inside cover assembly - black plastic with metal trim

IN-220-EM02-MW-xxx** Inside cover assembly - white plastic with metal trim

ITEMPART NO./ORDER

STRING DESCRIPTION QTY.


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Parts Breakdown (Continued)5

10

5 6

511

3

1 2

10

5 5

5

4

7

8

1 Consult Factory #41 Mortise cylinder 1

2 Consult Factory Cylinder Rosette 1

3 IN-220-7976-hand-fin Lock body with deadbolt with cylinder 1

IN-220-7977-hand-fin Lock body with deadbolt without cylinder

IN-220-7978-hand-fin Lock body without deadbolt with cylinder

IN-220-7979-hand-fin Lock body without deadbolt without cylinder

IN-220-82276-hand-fin Lock body with deadbolt with cylinder (not shown)

IN-220-82277-hand-fin Lock body with deadbolt without cylinder (not shown)

IN-220-82278-hand-fin Lock body without deadbolt with cylinder (not shown)

IN-220-82279-hand-fin Lock body without deadbolt without cylinder (not shown)

4 Consult Factory Turn lever 1

5 82-3211 Trim Pack - 8200 Standard levers 1

82-5357 Trim Pack - 8200 Deco Levers & 7900 all lever styles (shown)

6 Consult Factory Rose

7 Consult Factory Inside lever 1

8 79-0035 Lock front - 7900 - Without deadbolt 1

79-0036 Lock front - 7900 - With deadbolt (shown)

82-0578 Lock front - 8200 - Without deadbolt

82-0579 Lock front - 8200 - With deadbolt

9 52-5373 Door Position Switch (DPS) Pack** -not required for 8200 1

10 77-4236 Mortise screw pack - specify finish (includes: wood and metal lock body screws, faceplate screws, and strike screws)

1

11 Consult Factory Outside trim 1

12 A8150 Field prep template (not shown) 1

13 4713 Door manufacturers template (not shown) 1

14 A8204B Instructions (this manual) 1

ITEMPART NO/ORDER

STRING DESCRIPTION QTY

9

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

Installation Wiring6

OverviewSARGENT IN220 PoE Typical Application

LMT: Lock Management Tool

A. PoE frame harness assembly

B. PoE data hinge from McKinney C. PoE door harness* from McKinney

D. IN220 PoE Lock

E. DPS: Door Position Switch (Needed on Cylindrical and Exits only)

* Door width determines length

Network Cable

Network Switch (802.3af)

Surface Mount RJ45

A

BC

E

D


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Molex-F Molex-F Molex-M

Cable: Cat 5e,26 AWG stranded,

100ohm

RJ45-M

Molex-M

Cabl

e: C

at 5

e or

hig

her

24 A

WG

, 100

ohm

B-Splice Crimp Connector

PoE Lock

Ceiling

Supplied by CI

GroundRing Terminal

Secured to Lock Mounting Plate

Frame-SideHarness

Assembly(15' length)

24AWG Stranded

Drain Wire for

Earth Ground in 15' Frame

Harness

Cable drain wire concealed in shrink tubing

Patch PanelDrain Wire Terminated on Rack

Cable: Cat 5e or higher24 AWG

RJ45-F Jack

Approved Software

Certified Integrator (CI) supplies and terminates the B-Splice connector and the

male RJ45 connector from harness to end user provided facility cable

Supplied by End User

PoE Switch

PoE Switch isTerminated toEarth Ground

Patch Cable Patch Panel to

PoE Switch

Wiring to TIA/EIA 568-B Standard

A

Notes:

• Connectors go on only one way. They cannot be placed in an incorrect position.

• Do not force and do not offset connectors

• Be sure they are completely seated (flush)

• PoE power source cannot be connected to a receptacle controlled by a switch

B

C

D

To building or electrical ground

RJ45-M

Installation Wiring (Continued)

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

Installation Wiring (Continued)

Components and wire harness supplied by McKinney. Suggested installation:

RJ45-M

Molex-M

Cab

le: C

AT 5

e or

hig

her

24 A

WG

100

ohm

B-Splice Crimp Connector

Ceiling

Supplied by CI

Cut end / ceiling-side PoE harness:

TIA/EIA 568-B Standard Wiring

1 2 3 4 5 6 7 8

Do not confuse pair numbers with pin numbers. A pair number is used for reference only (eg: 10BaseT Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack.

Frame-SideHarness

Assembly(15' length)

24AWG Stranded

Drain Wire for

Earth Ground in 15' Frame

Harness

Cable drain wire concealed in shrink tubing

Frame Harness Installation

Hinge side of PoE (Frame) harness:

4-pin M

6-pin M

FramePoE Hinge

PoE Data Hinge

Hinge-side harness connectors:

• 4-pin female molex connector

• 6-pin female molex connector with ground wire

Lock-side harness connectors:

• 4-pin female molex connector

• 6-pin female molex connector with ground wire

B

A

1. Feed cut end of harness into hole on hinge-side through single access hole.

2. Push one connector back through the hole and feed into the other access hole.Each of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness:

• 4-pin male molex connector

• 6-pin male molex connector with ground wire

PIN Wire Pair Number

1 White/Orange 2

2 Orange 2

3 White/Green 3

4 Blue 1

5 White/Blue 1

6 Green 3

7 White/Brown 4

8 Brown 4

1 8pin 8 1pin

4-pin F

6-pin F

4-pin F

6-pin F


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


IN220 PoE Lock

Order of installation may vary. Refer to appropriate sections for instructions.

Hinge-side harness connectors:

• 4-pin male Molex connector

• 6-pin male Molex connector with ground wire

Lock-side harness connectors:

• Ring terminal

• Male RJ45 connector (crimped after cable is fed through door)

Notes:

• Connectors go on only one way. They cannot be plugged to incorrect position.

• Do not force and do not offset connectors.

• Be sure they are completely seated (flush).

4-pin F 4-pin M4-pin F

6-pin F 6-pin F 6-pin M

Cable: CAT 5e,26 AWG stranded,

100ohm

Drain Wire

RJ45-M

PoE Hinge

PoE Door Harness

PoE Door Harness

Order of installation may vary. Refer to appropriate sections for instructions.

1. Prop door open.

2. Using the ring terminal, carefully route the assembly through the door channel toward lock.

PoE LockD

C

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

A. Verify Hand and Bevel of DoorStand on outside of locked door when determining door hand.

Lock Installation

LH Left Hand

Hinges Left Open Inward

LHRB Left Hand

Reverse Bevel Hinges Left

Open Outward

RH Right Hand

Hinges Right Open Inward

RHRB Right Hand

Reverse Bevel Hinges Right

Open Outward

Fig. 1A

1 Prepare Door

6

C. Door Preparation

Prior to installation, all holes must be free of burrs, debris and sharp edges.

Prepare door according to appropriate template (see website www.intelligentopenings.com).• Field Template: A8150 (ships with product)• Door Manufacturer’s Template: 4713

Outside Cylinder Hole(only with cylinder

installation)

Outside of Door Inside of Door

Cable Hole

Lever Holes

Through-bolt Hole

Cable Hole

Inside of Lock body Wire Hole

Lever HolesMortisedPocket

Thumb Turn Hole

Fig. 1B Wood Door Preparation

External DPS Hole

Through-bolt Hole

Channel for Cat 5e cable from hingeChannel for Cat 5e

cable from hinge(Not required for 8200)

B. Verify Product Label


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


2A Prepare 7900 Lock Body*

1. Reverse Lock Hand (If Required)

a. Rotate the latchbolt 180° (Fig. 2B).

b. Flip deadlatch by hand to match bevel of latchbolt.

2. Reverse Latch Hand (If Required)

Fig. 2A1

Locking piece

Fig. 2A2

Locking pieceDeadlatch

Latchbolt

Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):

a. Position lock body with red surface of locking piece visible.

b. Insert blade type screwdriver into locking piece slot to rotate lock-ing piece toward back of lock body.

c. Rotate the locking piece 180° un-til RED surface is on opposite side.

Note: Red indicates locked side (outside).

*If 7900 is type of lock being installed

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2B1):

a. Position lock body with red surface of locking piece visible.

b. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.

c. Rotate the locking piece 180° until RED surface is on opposite side.

Note: Red indicates locked side (outside).

Beveled surface of latch must face strike (Fig. 2B2).

The deadlatch is self adjusting.

To change hand of latchbolt:

a. Insert screwdriver into spade (triangular)- shaped slot.

b. Rotate screwdriver 90º to push latch out until back of latch clears lock front; then rotate latch 180º.

Latch will then re-enter lock body.

Note: Latch cannot be unscrewed.

Fig. 2B1

Locking Guide Slot:Red color indicates

locked side.

Push In

Right HandLock Shown

2B Prepare 8200 Lock Body*

1. Reverse Lock Hand

2. Reverse Latch HandTriangular Slot

Latchbolt

Fig. 2B2

*If 8200 is type of lock being installed


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Inside of Door

3 Install Door Position Switch (DPS)

1. Push wires through raceway toward lock prep.

2. Push DPS firmly into place by hand. Note: DO NOT TAP SWITCH WITH ANY TOOL.

3. Install magnet into door frame. Push firmly into place by hand. See instruction A7983A.

Fig. 3

Door Position Switch (DPS)

CAUTION: if DPS is not installed or is installed improperly, door status monitoring features will not function.

* Only required with the 7900 lock body - 8200 has an integrated DPS

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

4 Install Lock Body

1. Feed the wire harness into the mortise pocket and through inside preparation hole as depicted in Figure 4.

2. Carefully push the lock body into the pocket while lightly applying tension to the wire harness.

Fig. 4

(2) #12-24 screws

Inside of Door

Door Position Switch (DPS)

Wire Harness

Note: Do not pull the lock into the pocket using the harness alone.

Ensure that the wire harness is not pinched between the lock and the mortise pocket.

3. Insert (2) #12-24 screws into the lock body (Fig. 4) and tighten* with a screw driver.

*Do not fully tighten until cylinder and levers are installed and properly aligned.

Ground Wire


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Fig. 5B Fig. 5C

Outside of Door

5 Outside Cylinder Installation

Rosette

Spring

Cylinder

IMPORTANT: Position cylinder so that the SARGENT logo is positioned correctly.

Correct Incorrect

Fig. 5A

1. Slide the spring and the rosette onto the cylinder.

2. Rotate the cylinder into cylinder hole with fingers.

3. Insert key 75% of the way and utilize the key to rotate the cylinder into the rest of the cylinder hole. Note: Do not attempt to tighten all the way.

4. Verify that orientation of cylinder has the SARGENT logo as depicted in Fig. 5A.

5. Hand tighten the cylinder clamp screw with Phillips screwdriver to prevent unscrewing of the cylinder (Fig 5C).

6. Test cylinder function:

• Key retracts latchbolt and deadbolt (7976 & 82276 functions).

• Key retracts latchbolt (7978 & 82278 functions).

• Cylinder not present for 7977, 7979, 82277 and 82279 functions.

Cylinder Clamp Screw

Phillips Screwdriver

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

Inside of DoorOutside of Door

DPS

Fig. 6BFig. 6A

6 Assemble Outside Trim

1. With outside lever horizontal, insert the mounting posts through outside of door and lock body.

Make certain the lever spindle is properly engaged inside the lock body (Fig 6A).

2. On the inside of the door, insert spindle into square hole of mortise lock (Fig 6B).

3. Slide inside adapter and plate assembly over spindle and secure with (2) 8-32 X 5/8” Phillips oval head and lock washer machine screws.

NOTE: For 8200 Deco levers and all 7900 lever styles, ensure that position of set screw hole on inside adapter is oriented to match location of hole in inside lever handle.

Also, ensure that slot in spindle is facing away from door (Fig. 6B), and is oriented to match location of hole in inside lever handle.

Wire Harness(From Lock Body)

Spindle

Outside Trim

Spindle

Fig. 5A Detail

Outside TrimSet Screw Hole


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Fig. 7

Set Screw

Inside Lever

Spindle

Rose

1. Place inside rose flush against door surface and rotate first counter-clockwise to seat the threads, then clockwise to securely tighten.

2. Slide lever onto spindle until fully seated. Be sure handle is horizontal and facing the hinge side of the door. Push lever onto spindle so minimum gap is visible.

3. Tighten the set screw securely with a T20 Torx® driver.

4. Finish securely tightening (2) #12-24 lock body screws.

5. Before closing the door, test that the lever is functional and ensure smooth operation of the latchbolt.

7 Install Inside Rose and Inside Lever Assembly

Inside of Door

#12-24 screws

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

8 Install Thumb Turn

1. Insert thumb turn into preparation hole and engage slot in lock body.

2. Orient mounting plate so screw hole is vertical (aligned with preparation holes).

3. Secure plate with Phillips screw provided.

4. Test thumb turn for function by turning to retract and project the deadbolt.

9 Attach Front Plate

Attach front plate with (2) Phillips head screws.

Outside of Door

Fig. 9

(2) Phillips head screws

Fig. 8

Thumb Turn

Inside of Door

Phillips screw


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


10 Outside Reader and Mounting Plate Installation

1. Orient the reader so the LED lens is at the top.

2. Feed the cable/connector through the door (from outside to inside).

3. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes. Hold the reader flush against door while ensuring proper alignment.

Fig. 10A

LED

Reader Assembly with Harness

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

4. Next feed the cables/connectors through the inside mounting assembly (and gasket if required*).

5. Insert and partially tighten (2) through-bolts prior to installation of connectors.

NOTE: Cable lengths exaggerated for illustrative purposes.

10 Outside Reader Installation (Continued)

*Gasket is required for outdoor installations.

If installing with gasket; separate gasket from mounting plate to feed cables/connectors through holes as indicated (Fig. 10B).

Once cables/connectors are fed through, reattach gasket to mounting plate.

Gasket*

Inside Mounting Plate

Fig. 10B

Inside of Door

Cat 5e cable from hinge (with ground wire)

Through-bolts

Ground wire (Lock Body)

6. Secure both ground lugs with #6-32 machine screw (Fig.10C).

Fig. 10C


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


1. Tuck excess cable into wire hole on inside of door.

2. Secure the mounting assembly while ensuring proper alignment of outside reader and fully tighten the (2) through- bolts on the inside of the door to secure the reader and plate to the door.

Secure the following connectors to their respective terminals (Fig. 11A, B):

A. Secure the 4-pin DPS connector.

B. Secure the 10-pin lock body assembly connector.

CAUTION - Do not touch or allow debris to enter connector contacts.

Secure Mounting Plate

IMPORTANT: Do not run wires through bottom hole in plate (Fig. 11A, B) - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 11B).

C. Secure the 24-pin card reader connector (Fig. 11B).

11 Installation of Connectors

D. Crimp* RJ45 to Cat 5e cable from hinge (Fig. 11C).

*For more detail, refer to section (5) ‘Installation Wiring’, “A - Frame Harness Installation”.

Ground Lugs

DPS (4-pin)A

Lock Body (10-pin)

Fig. 11A

B

Reader (24-pin)

Board-to-Board Connector

Fig. 11B

TIA/EIA 568-B Standard Wiring

1 2 3 4 5 6 7 8

Do not confuse pair numbers with pin numbers. A pair number is used for reference only (eg: 10BaseT Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack.

PIN Wire Pair Number

1 White/Orange 2

2 Orange 2

3 White/Green 3

4 Blue 1

5 White/Blue 1

6 Green 3

7 White/Brown 4

8 Brown 4

Crimp* to RJ45-M Connector

Cat 5e cable from hinge

RJ45-M

C

Fig. 11C

1 8pin 8 1pin

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

12 Installation of Inside Module Component Assembly 1. Insert top tabs of controller into slots on mounting plate (Fig. 12A, B).

2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate.

CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.

Fig. 12B

4. Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab (Fig. 12B).

3. Connect RJ45 male connector to female RJ45 port on controller board (Fig. 12B).

Fig. 12A

Coin Cell Pull Tab


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


13 Inside Cover Installation1. Assemble cover by hooking top edge on inside mounting plate.2. Carefully press bottom of cover toward door without pinching wires.3. Secure the cover with the security allen wrench.

Inside Cover

Security Allen Screw

Inside of Door

04/3

0/16


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.

IN220 Mortise Lock

For 7976- and 7978-function mortise locks with cylinders:

1. Insert key into cylinder and rotate.

There should be no friction against lock case, wire harness or any other obstructions.

2. Check that the key retracts the latch: the key should rotate freely.

3. Throw the deadbolt (if present): Check that the key retracts both the deadbolt and the latch.

4. Try the inside lever: Ensure it retracts latch and deadbolt (if installed).

5. Use a valid credential* set up with the Lock Configuration Tool to unlock outside lever and retract latch.

Refer to Network and Lock Configuration Tool user manual (WFMN1) for information on how to configure and program locks.

Operational Check 8

Fig. 14B

Fig. 14A

Note: The credential should approach the inscription on the reader as indicated (Fig. 15B) to ensure that the credential is read properly.

Do not wave credential.

*Twenty (20) seconds after lock initialization (single beep with lock motor actuation).


Copy

right

© 2

016,

Sar

gent

Man

ufac

turin

g Co

mpa

ny, a

n AS

SA A

BLOY

Gro

up co

mpa

ny. A

ll rig

hts r

eser

ved.

Re

prod

uctio

ns in

who

le o

r in

part

with

out e

xpre

ss w

ritte

n pe

rmiss

ion

of S

arge

nt M

anuf

actu

ring

Com

pany

is p

rohi

bite

d.04

/30/


Notes

SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.com

Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.

Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A8204B - 04/16

mortise lock installation instructions - assa abloy · 2017. 6. 15. · 8 79-0035 lock front - 7900...

Documents