monogram 36 built-in all-freezer › documents › 108649 › zif360nnrh-spec sheet.pdfmonogram...

OF 17For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19

CUSTOM PANEL MODEL Can be personalized with cabinet-matching panels and handles

FLUSH INSET INSTALLATION Allows the refrigerator to be installed flush with adjacent cabinetry

ENHANCED TEMPERATURE MANAGEMENT SYSTEM With precise electronic controls and thermistors, maintains ideal storage conditions for frozen foods

CONCEALED ICE DRAWER Provides quick and easy access to filtered ice

GE WATER FILTRATION SYSTEM Provides clean, fresh-tasting water to the freezer's icemaker

ADJUSTABLE, WIRE SHELVES, GALLON-SIZE DOOR BINS AND PULLOUT BASKETS Allow customizable storage for foods and containers of varying sizes

CONCEALED HALOGEN LIGHTING SYSTEM Illuminates contents without compromising space

MONOGRAM 36" BUILT-IN ALL-FREEZERZIF360NNLH

For questions about your appliance, please call 1-800-626-2000. Product Specification Created 10/19PAGE 2 OF 17

STANDARD INSTALLATION

SECTION 2

SECTION 1

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

REQUIRES ADDITIONAL TRIM KIT ZKFN

FLUSH INSET INSTALLATION

For questions about your appliance, please call 1-800-626-2000.

Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.

OVERALL DIMENSIONS

Product Specification Created 10/19PAGE 3 OF 17

ATTENTION ELECTRICIAN:A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

SPECIFICATIONS

Overall Width 36" (91.4 cm)

Overall Height 84" (213.4 cm)

Overall Depth 25 1/8" (63.8 cm)

Door Clearance 36 1/2" (92.7 cm)

Cutout Width 35 1/2" (90.2 cm)

Cutout Height 83 1/2" - 84 1/2" (212.1 - 214.6 cm)

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit

Shipping Weight 569 lb (258 kg)

36" (91.4)

25 1/8" (63.8)

23 5/8" (60.0)

*84"(213.4)

*73 7/16"(186.5)

*3 1/4"(8.3)

*83 1/2"(212.1)

36 1/2"(92.7)TOP VIEW

35" (88.9)Case width

70 7/16"(178.9)

*3"(7.6)

ZIF360NXLH

SIDE VIEWFRONT VIEW* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.

** 4 9/16" (11.6) min clearance to a wall for 90˚ door swing

** These refrigerators are equipped with a 3 position door stop. The factory set 115˚ door swing can be adjusted to 90˚ if clearances to adjacent cabinets or walls is restricted. Allow full 130˚ door swings for pan removal. If the 90˚ door stop position is used, pan access is maintained, but pan removal is restricted.

** Dimensions are based on custom handle height of 2 9/16" (6.5).

** Allow 25" (63.5) min clearance for 130˚ door swing




HELPFUL TIPS

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure 81 1/2" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32 1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.


SIDE VIEW

W

25 3/8" (64.5)

1 1/2"(3.8)

7/16" (1.1)Trim overlap

3 1/2"(8.9)

FRONT VIEW

ELEC.

35 1/2" (90.2)2 5/16"

(5.9)

*83 1/2" min*84 1/2" max

(212.1-214.6)*Trim will overlapadditional 7/16"

3 1/2"(8.9)

75 1/2"(191.8)

From floorto bottom

of electricalarea

5 1/2"(14.0)

9"(22.9)

ZIF360NXRH

SIDE VIEW INSTALLEDWITH ANTI-TIP BRACKET

5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

81 1/2"(207.0)

Use two additional hole

locations at end of

bracketsWall

Studs

Bracket mounted

into vertical wall studscenteredwithin the

cutout

C

Ensure holesselected arecentered on

the studs

L

FRONT VIEW OF CUTOUTWITH ANTI-TIP BRACKET

A

B

ANTI-TIP BRACKET

SIDE VIEW

W

25 3/8" (64.5)

1 1/2"(3.8)


3 1/2"(8.9)

FRONT VIEW

ELEC.

35 1/2" (90.2)2 5/16"

(5.9)

*83 1/2" min*84 1/2" max


3 1/2"(8.9)

75 1/2"(191.8)

From floorto bottom

of electricalarea

5 1/2"(14.0)

9"(22.9)

ZIF360NXRH


5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

81 1/2"(207.0)


locations at end of

bracketsWall

Studs

Bracket mounted


cutout

C


the studs

L




STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION

STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION

Grille Panel

DoorPanel

A

B

C

Grille Panel

DoorPanel

A

B

C

Door

1/4" Framed Panel Optional ZKLN kit handle

Trim

Door1/4" Backer Panel

.10" Spacer PanelOptional ZKLNkit handle

Trim

3/4" Overlay Panel

Trimmed freezers are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

Maximum total panel weight: • Door panel – 67 lbs. • Grille panel – 11 lbs.

3/4" Overlay Panels: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.


Door Handles: Door handles are not provided. Custom handles supplied by your cabinet maker may be used. An optional visor handle can be ordered as kit ZKLN.

A B C1/4" Framed Panel 33 7/8" 8 7/8" 69 5/16"

A B C1/4" Backer Panel 33 7/8" 8 7/8" 69 5/16"

.10" Spacer Panel 32 1/2" 7 5/8" 67 15/16"

3/4" Overlay Panel 34 1/8" 9" 69 9/16"

HELPFUL TIPS



HELPFUL TIPS

F Side panels must be used whenever the sides of the freezer will be exposed. A 1/4" side panel will slip into the side case trim. Secure the panels to the freezer with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.

CUSTOM SIDE PANELS

F

2 9/16"(6.5)

*3"- 4"(7.6 - 10.2)

*Dependingon installation

height

1 7/8"(4.8)

24" (61.0)

3/16"(.5)

*84"(213.4)

*Dependingon installation

height

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRHZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH



HELPFUL TIPS

A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.

Additional cutout width may be required when side panels are used.

Trimmed freezers are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

Maximum total panel weight: • Door panel – 67 lbs. • Grille panel – 25 lbs

Order a ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION

PANEL DIMENSIONS

PANEL ASSEMBLY CROSS SECTION

Grille Panel

DoorPanel

D

A

DoorPanel

B

C

D

Door

1/4" Framed Panel Optional ZKLN kit handle

Trim

71 1/2" (181.7)Finished Width

24" (61)Min. Cutout Depth24 3/16" (61.4)4 5/16"

(11.0)

5 1/2"(13.9)

9"(22.9)

83 1/2" min84 1/2" max


3 1/2"(8.9)

ZIF360NHLH_ZIF360NHRH _ZIFP360NHLH_ZIFP360NHRH_ ZIFS360NHLH_ZIFS360NHRHZIR360NHLH_ZIR360NHRH_ZIRP360NHLH_ZIRP360NHRH_ZIRS360NHLH_ZIRS360NHRH

W

FRONT VIEW

ELEC. 5 1/2"(13.9)

9"(22.9)

3 1/2"(8.9)

25" (63.5) minTo wall


5" (12.7) min


1"(2.5)

2" min(5.1)

130˚Door swing

130˚Door swing

75 1/2"(191.8 )

From floorto bottom

of electricalarea

ELEC.

SIDE VIEW

5"(12.7)

5"(12.7)

5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

WATER3 1/2"

(9.0)

DUAL INSTALLATIONS

A

A B C D1/4" Framed Panel 69 7/8" 8 7/8" 69 5/16" 33 7/8"



HELPFUL TIPS

A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required.


B In a side-by-side installation with same door swing, allow 2" minimum clearance between the products to prevent the door swing interference. Allow 15" minimum to a wall to achieve full drawer extension and pan removal. Additional clearances are required when using custom panels and handles.

NOTE: ZKBSN720NSS and ZKBFN720NII unification kits will not fit this installation.

C In a side-by-side installation with right and left door hinges together, allow 5” minimum clearance between the two products to prevent one door from striking the other. Additional clearances required when using custom panels and handles.

NOTE: ZKBSN720NSS and ZKBFN720NII unification kits will not fit this installation.

DUAL PRODUCT CLEARANCES

71 1/2" (181.6)Finished Width

24" (61.0)Min. Cutout Depth24 3/16" (61.4)2 5/16"

(5.9)

5 1/2"(13.9)

9"(22.9)

83 1/2" min84 1/2" max

(212.1-214.6)Finished Opening

3 1/2"(8.9)

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRHZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

W

FRONT VIEW

ELEC. 5 1/2"(13.9)

9"(22.9)

3 1/2"(8.9)

23 1/8" (58.7) minTo wall

23 1/8" (58.7) minTo wall

5" (12.7) min

23 1/8" (58.7) minTo wall

1"(2.5)

2" min(5.1)

130˚Door swing

130˚Door swing

75 1/2"(191.8 )

From floorto bottom

of electricalarea

ELEC.

SIDE VIEW

5"(12.7)

5"(12.7)

5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

WATER3 1/2"

(9.0)

STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION

PANEL ASSEMBLY CROSS SECTION

.25" + .10" + .75" = 1.10" Total Panel Thickness

Grille Panel

DoorPanel

D

A

DoorPanel

B

C

D

Door1/4" Backer Panel

.10" Spacer PanelOptional ZKLNkit handle

Trim

3/4" Overlay Panel

3/4" Overlay Panels: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.



Door Handles: Door handles are not provided. Custom handles supplied by your cabinet maker may be used. An optional visor handle can be ordered as kit ZKLN.

C

BA

PANEL DIMENSIONS

A B C D1/4" Backer Panel 69 7/8" 8 7/8" 69 5/16" 33 7/8"

.10" Spacer Panel 68 1/2" 7 5/8" 67 15/16" 32 1/2"

3/4" Overlay Panel 70 1/8" 9" 69 9/16" 34 1/8"

For questions about your appliance, please call 1-800-626-2000.

Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.

OVERALL DIMENSIONS

Product Specification Created 10/19PAGE 9 OF 17

ATTENTION ELECTRICIAN:A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

SPECIFICATIONS

Overall Width 38" (96.5 cm)†

Overall Height 84 11/16" (215.1 cm)†

Overall Depth 26 1/8" (66.4 cm)†

Door Clearance 38 3/4" (98.4 cm)

Cutout Width 39" (99.1 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper tubing or GE SmartConnect kit

Shipping Weight 569 lb (258 kg)

† Dimensions include 3/4" custom cabinet panel

38" (96.5)

*84 11/16"(215.1) *73 3/4"

(187.3)

69 3/4"(177.2)

ZIF360NHLH

FRONT VIEW* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84 11/16".

10 15/16"(27.8)

20 5/8" (52.5)

26 1/8" (66.4)

*4"(10.2) SIDE VIEW

* 84"(213.4)

35" (88.9)Case width

38 3/4"(98.4)

TOP VIEW

** 4 9/16" (11.6) minclearance to a wallfor 90˚ door swing

** Dimensions based on custom handle height of 2 9/16" (6.5).

** Allow 15" (38.1) minclearance for 115˚door swing

20 5/8"(52.5)




HELPFUL TIPS

FLUSH INSTALLATIONZIF360NHLH_RHZIR360NHLH_RH

39" (99.1) Flush inset width

37 1/2" (95.3)Width between cleats

7"(17.8)

7"(17.8)

3/4" (1.9)Width of side cleats

5 1/4" (13.3)

1/2" (1.3)26 3/16" (66.5)Flush inset depth

20 15/16" (53.2)Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

3 1/2"(8.9)

W

Finished cleats

Finished cleats

Case Trim

3/4" Panel

Case

Door

5 1/2"(14.0)

24 3/16"(61.4)

9"(22.9)

ELEC.

3 1/2"(8.9)

75 1/2"(191.8 )

From floorto bottom

of electricalarea

WATER3 1/2"

(9.0)

85"(215.9)

85"(215.9)

C

B

ANTI-TIP BRACKET

SIDE VIEW

W

25 3/8" (64.5)

1 1/2"(3.8)


3 1/2"(8.9)

FRONT VIEW

ELEC.

35 1/2" (90.2)2 5/16"

(5.9)

*83 1/2" min*84 1/2" max


3 1/2"(8.9)

75 1/2"(191.8)

From floorto bottom

of electricalarea

5 1/2"(14.0)

9"(22.9)

ZIF360NXRH


5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

81 1/2"(207.0)


locations at end of

bracketsWall

Studs

Bracket mounted


cutout

C


the studs

L




C Top cleat should be 1" thick

WARNING: The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.











FLUSH INSET INSTALLATION 3/4" PANELS

A


3/4" PANEL BOTTOM VIEW(AFTER ROUTING)

LEFTSIDE

RIGHTSIDE

Front

Back

DETAIL TOP

DETAIL BOTTOM

1/8"

1-7/16"

RO

UTE

R D

EP

TH 1/4"

Grille Panel

DoorPanel

A

B

C

PANEL DIMENSIONS

FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door and grille trims.


Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.

Door Handles Custom handles are required for flush installation.


3/4" GRILLE DOOR PANEL ROUTING

Front

NOTE: Routed areas should be finished as they may be visible when assembled.

CORNER VIEW SHOWING“PICTURE FRAME” ROUTING

Back

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW(AFTER ROUTING)

DETAIL LEFT SIDE

DETAIL RIGHTSIDE

2-1/16" 2-1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

1/4"

3/32"


HELPFUL TIPS

A B C38" 10 7/16" 69 3/4"


3/4" RAISED DOOR PANEL ROUTING

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door and grille trims.



Door Handles Custom handles are required for flush installation.


TOP

FrontBack

BOTTOM


3/4"

11/32"1/4"

1/4"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

DETAIL LEFT SIDE

DETAIL RIGHTSIDE

2-1/16" 2-1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

1/4"

3/32"


LEFTSIDE

RIGHTSIDE

Front

Back

Front



Back


HELPFUL TIPS


FLUSH INSET INSTALLATION 1/2" PANELS

FLUSH INSTALLATION???? ZIF360NHLH_RH???? ZIR360NHLH_RH

39" (99.1) Flush inset width

37 1/2" (95.3)Width between cleats

7"(17.8)

7"(17.8)

3/4" (1.9)Width of side cleats

5 3/8" (13.7)

1/2" (1.3)26 3/16" (66.5)Flush inset depth

20 13/16" (52.9)Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

3 1/2"(8.9)

W

Finished cleats

Finished cleats

Case Trim

1/2" Panel

Case

Door

5 1/2"(14.0)

24 3/16"(61.4)

9"(22.9)

ELEC.

3 1/2"(8.9)

75 1/2"(191.8 )

From floorto bottom

of electricalarea

WATER3 1/2"

(9.0)

85"(215.9)

85"(215.9)

A

B

ANTI-TIP BRACKET



C Top cleat should be 1" thick

WARNING: The freezer is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.











C

SIDE VIEW

W

25 3/8" (64.5)

1 1/2"(3.8)


3 1/2"(8.9)

FRONT VIEW

ELEC.

35 1/2" (90.2)2 5/16"

(5.9)

*83 1/2" min*84 1/2" max


3 1/2"(8.9)

75 1/2"(191.8)

From floorto bottom

of electricalarea

5 1/2"(14.0)

9"(22.9)

ZIF360NXRH


5"(12.7)

5"(12.7)

WATER3 1/2"

(9.0)

81 1/2"(207.0)


locations at end of

bracketsWall

Studs

Bracket mounted


cutout

C


the studs

L



HELPFUL TIPS


Grille Panel

DoorPanel

A

B

C

C

DA B

Hinge Side

Backer with Overlay Panel Assembly

Door Panel Back

PANEL DIMENSIONS

PANEL DIMENSIONS

FLUSH INSET 1/2" PANEL DIMENSIONS SINGLE INSTALLATION

1/2" OUTER PANEL TO BACKER PLACEMENT

C

DA B

Grille Back

1/2"OverlayPanel

1/4"BackerPanel

Door

.10"Spacer

The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel




HELPFUL TIPS

A B C1/4" Backer Panel 33 7/8" 8 7/8" 69 5/16"

.10" Spacer Panel 32 1/2" 7 5/8" 67 15/16"

1/2" Overlay Panel 38" 10 7/16" 69 3/4"

A B C DDoor Panel 2 1/16" 2 1/16" 3/16" 1/4"

.Grill Panel 2 1/16" 2 1/16" 1 7/16" 1/8"


ZIF360NHLH_ZIR360NHRH

75" (190.5)Finished Width

26 3/16" (66.5)Min. Cutout Depth24 3/16" (61.4)4 5/16"

(10.9)

5 1/2"(13.9)

9"(22.9)

85"(215.9)

FinishedOpening

3 1/2"(8.9)

W

FRONT VIEW

ELEC. 5 1/2"(13.9)

9"(22.9)

3 1/2"(8.9)



1 1/2"(3.8)

115˚Door swing

115˚Door swing

75 1/2"(191.8 )

From floorto bottom

of electricalarea

ELEC.

SIDE VIEW

7"(17.8)

7"(17.8)

WATER3 1/2"

(9.0)

WATER3 1/2"

(9.0)7 1/2"(19.1)

7 1/2"(19.1)

DUAL INSTALLATIONS

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

Maximum total panel weight: • Fresh food door panels – 67 lbs. • Grille panel – 25 lbs

Door Handles: Custom handles are required for flush installation.


The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws: • Center the spacer panel on the backer

panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the single unit flush installation diagram on pg 7 for backer to 1/2" overlay panel placement.

A A Separate 115V, 60Hz, 15 or 20 amp power supply is recommended for each product.

Grille Panel

DoorPanel

D

A

DoorPanel

B

C

D

PANEL DIMENSIONS

FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION


HELPFUL TIPS

A

A B C D1/4" Backer Panel 69 7/8" 8 7/8" 69 5/16" 33 7/8"

.10" Spacer Panel 68 1/2" 7 5/8" 67 15/16" 32 1/2"

1/2" Overlay Panel 74" 10 7/16" 69 3/4" 36 7/8"


Grille Panel

DoorPanel

D

A

DoorPanel

B

C

D

FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

Trimmed freezers are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

Maximum total panel weight: • Fresh food door panels – 67 lbs. • Grille panel – 25 lbs.

Door Handles: Custom handles are required for flush installation.


3/4" RAISED DOOR PANEL ROUTING (SEE PAGE 10 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)

TOP

FrontBack

BOTTOM


Front



Back

HINGESIDE

HANDLESIDE

Front

Back


3/4"

11/32"1/4"

3/16"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

2 1/16" 3/16"

ROUTER DEPTH 1/4"

DETAIL HINGESIDE

DETAIL HANDLESIDE


HELPFUL TIPS

PANEL DIMENSIONS

A B C D74" 10 7/16" 69 3/4" 36 7/8"


DUAL PRODUCT CLEARANCES

ZIF360NHLH

16 3/8" min (41.6) To wall

16 3/8" min (41.6) To wall

1"(2.5)

115˚Door swing

115˚Door swing

A

A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is achieved naturally when installing trim-to-trim.


HELPFUL TIPS

monogram 36 built-in all-freezer › documents › 108649 › zif360nnrh-spec sheet.pdfmonogram...

Documents