modul 04 - wtp 104 technical and building drawing
TRANSCRIPT
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
1/8
December Edi tion 2013
MINISTRY OF EDUCATION, MALAYSIA
VOCATIONAL COLLEGE STANDARD CURRICULUM
COURSE NAME INFORMATION
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
LEVEL : 1 SEMESTER 1
CREDIT UNIT : 2.0
CONTACT HOUR : FACE TO FACE : 4.0 HOURS/WEEK
NON FACE TO FACE :
COURSE TYPE : VOCATIONAL
PREREUISITE : !
CORE REUISITE : !
Last Edited 10-13 November 2013
Module Page 1/7 Document Page 1
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
2/8
December Edi tion 2013
COURSE OUTCOMES:
At the end of the course, students should be able to:-
1 Carry out basic technical drawing2 identify types of drawings in building construction3 Pproduce various symbols in technical drawings and building plan Produce building plan for single storey building! interpret single storey building plan
COURSE DESCRIPTION
"his course is designed for students to master basic technical drawing by using appropriate drawing instruments which is according
to the building drawing standard# $t is also designed to enable them to draw and interpret the single storey building plan
Last Edited 10-13 November 2013
Module Page 2/7 Document Page 2
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
3/8
December Edi tion 2013
CONTENT AND LEARNING STANDARDS
PROGRAMME : CONSTRUCTION TECHNOLOGY
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
CONTENT STANDARD LEARNING STANDARD PERFORMANCE CRITERIA
1. CARRY OUT BASICTECHNICAL DRAWING
1#1 %et a drawing paper on drawingboard
1#1#1 %elect types and si&e of drawing paper for technicaldrawing according to specification
1#1#2 %etting the drawing paper on the drawing board byusing clips
1#2 $dentify appropriate drawing$nstruments
1#2#1 %elect appropriate drawing instruments according tospecification#
1#2#2 'raw the types of lines in drawing by using the drawinginstrument set
1#2#3 Apply the various techni(ues of letter writing by usingletter bloc) and free hand
1#3 Perform basic technical drawing 1#3#1 'raw basic technical drawing by using an instrument setas shown in the drawing sheet#
Last Edited 10-13 November 2013
Module Page 3/7 Document Page 3
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
4/8
December Edi tion 2013
CONTENT AND LEARNING STANDARDS
PROGRAMME : CONSTRUCTION TECHNOLOGY
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
CONTENT STANDARD LEARNING STANDARD PERFORMANCE CRITERIA
2. IDENTIFY TYPES OF
DRAWINGS INBUILDING
CONSTRUCTION
3.1*ecogni&e various types of drawing inbuilding construction
2#1#1 %elect the various types of drawing inbuilding construction according to +obspecification
2#2 erify type of drawing used in buildingconstruction
2#2#1 ist the drawings used in building accordingto +ob specification#
Last Edited 10-13 November 2013
Module Page 4/7 Document Page 4
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
5/8
December Edi tion 2013
CONTENT AND LEARNING STANDARDS
PROGRAMME : CONSTRUCTION TECHNOLOGY
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
CONTENT STANDARD LEARNING STANDARD PERFORMANCE CRITERIA
". PPRODUCE VARIOUSSYMBOLS IN
TECHNICAL
DRAWINGS AND
BUILDING PLAN
3#1 Apply standard symbols used in
related drawing
3#1#1 $dentify the symbols in technical drawings and building
plan according to drawing re(uirement3#1#2 'raw the types of symbols in technical drawing and
building plan using drawing instrument set
3.2 Apply standard drawing scale
used in drawing
3#2#1 $dentify drawing scale used in technical drawings and
building plan according to drawing re(uirement
3#2#2 .se the drawing scale in technical drawing according to
drawing re(uirement
3#2#3 .se the architectural scale in drawing plan
according to drawing re(uirement
Last Edited 10-13 November 2013
Module Page /7 Document Page
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
6/8
December Edi tion 2013
CONTENT AND LEARNING STANDARDS
PROGRAMME : CONSTRUCTION TECHNOLOGY
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
CONTENT STANDARD LEARNING STANDARD PERFORMANCE CRITERIA
4. PRODUCE BUILDING
PLAN FOR
SINGLE STOREY
BUILDING
#1 $nterpret building plan for single storey building
#1#1 /utline the specification and information fromthe drawing given
#2 'raw floor plan and scale #2#1# %et the drawing paper on the board using the paper clip#2#2 $dentify the orthography drawing building plan
according to drawing given#2#3 Perform drawing for floor plan and scale
according to drawing given
4.3 'raw front elevation, side
elevation and rear elevation
#3#1 $dentify front elevation, side and rear elevation
and scale according to drawing given#3#2 Perform drawing for front elevation, side and
rear elevation and scale according to drawinggiven
4.4 'raw roof plan ##1 %elect roof plan and scale according to drawingspecification
##2 Perform drawing for roof plan and scaleaccording to drawing specification
Last Edited 10-13 November 2013
Module Page !/7 Document Page !
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
7/8
December Edi tion 2013
4.5 'raw section view #!#1 $dentify section view and scale according todrawing given
#!#2 Perform drawing for section view with scaleaccording to drawing given
Last Edited 10-13 November 2013
Module Page 7/7 Document Page 7
-
7/25/2019 Modul 04 - Wtp 104 Technical and Building Drawing
8/8
December Edi tion 2013
CONTENT AND LEARNING STANDARDS
PROGRAMME : CONSTRUCTION TECHNOLOGY
COURSE NAME : TECHNICAL AND BUILDING DRAWING
CODE NAME : WTP 104
CONTENT STANDARD LEARNING STANDARD PERFORMANCE CRITERIA
#. INTERPRET SINGLE
STOREY BUILDING PLAN
!#1 $dentify the building drawing
!#1#1 'etermine the types, shapes and si&es of materialdrawing according to drawing plan
!#1#2 'etermine the types of finishing and theirapplications according to drawing plan
!#2 $dentify related drawing !#2#1 'etermine related drawing according to singlestorey building plan#
!#2#2 /utline all specification and information from thesingle storey building plan
Last Edited 10-13 November 2013
Module Page "/7 Document Page "