models super v6000 vho super v6000 vs-r™tanning-bed-parts.com/documents/ets tan documentati… ·...

M O D E L S S U P E R V 6 0 0 0 V H O

S U P E R V 6 0 0 0 V S - R™22028A

A S S E M B L Y A N D U S E R G U I D E

R

Limited Lifetime Warranty

SUNVISION® warrants your tanning unit to be free of structural defects in its material and workman-ship, under normal use, for its lifetime. SUNVISION will repair or replace, at their discretion, any

defect to the structure which affects the performance of the unit.

For 6 months from the date of purchase, SUNVISION will provide replacements for parts that proveto be defective in material or workmanship. Acrylic shields, fluorescent lamps, and lamp starters areexcluded from this warranty. Labor will be covered for 30 days from purchase date. Normal wear,

damage from misuse or abuse, damage incurred in transit, or damage done by unauthorized repairsor modifications are not covered by this warranty.

ETS, Inc. disclaims any implied warranty of merchantability or fitness for any period beyond theexpressed warranty. Some states do not allow limitations on how long an implied warranty lasts, so

the above limitations may not apply to you.

No one has authority to change or modify this Limited Lifetime Warranty in any respect. To obtainservice under the Limited Lifetime Warranty, contact ETS, Inc. at 1-800-228-6292, and ask for the

Technical Service Department.

ETS, Inc. SHALL NOT BE LIABLE FOR LOSS OF USE, LOSS OF TIME , INCONVENIENCE, RENTAL ORSUBSTITUTE PRODUCTS, LOSS OF BUSINESS, LOSS OF INCOME, OR ANY OTHER INCIDENTAL OR

CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental orconsequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

All warranty service must be performed by an authorized service person. If your tanning unit mustbe returned for service, all freight charges must be at your expense. Contact your place of purchase

for the address of the SUNVISION Service Center nearest you. Proof of purchase is required toobtain warranty service.

This warranty covers the original purchaser only. This warranty is void if the unit is modified in any manner from its original design.

ii

Congratulations on your purchase of this technologically advanced sun tanning unit.It has been designed to provide years of dependable service for you.

Please read all the instructions in this booklet before installing and using the unit.Always be sure to observe all safety precautions.

ontentsCSafety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . .1Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Pre-Installation Planning . . . . . . . . . . . . . . . . . . . . . . . . .2Assembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . .3Bypass Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Remote Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Before You Tan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Exposure Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Using Your Booth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Cleaning After Use . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Thorough Periodic Cleaning . . . . . . . . . . . . . . . . . . . . .11Mechanical Inspection . . . . . . . . . . . . . . . . . . . . . . . . .11Replacing Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Obtaining Service . . . . . . . . . . . . . . . . . . . . . . . . . .back cover

elcomeW

iii

LABELING NOTICE: Labels are affixed on all systems to inform the user of possible dangers. Regulations are stated in21 CFR, Section 1040.20, and require that all products manufactured after September 8, 1986 which use sunlampsmust display the following:

Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexpo-sure can cause eye and skin injury and allergic reactions. Repeated exposure may cause pre-

mature aging of the skin and skin cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNSOR LONGTERM INJURY TO THE EYES.

Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before usingsunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive tosunlight. If you do not tan in the sun, you are unlikely to tan from the use of this product.

Do not use without wire grid in place. Tanning normally appears after the first few sessions and maximizes afterapproximately four weeks. Tan once or twice per week thereafter to maintain appearance. Frequency of sessionsshould be limited to every other day. Persons already having a base tan may begin at advanced levels corre-sponding to the extent of their base tan.

New lamps emit approximately 20% more ultraviolet radiation during the first 50 hours of operation. Recommendedtanning times should therefore be reduced by approximately 20% during that period.

For a uniform tan, center yourself within the booth both front and back and to the left and right. This will result inyour body being equidistant from all lamps. Other postions may result in over exposure to parts of your body.

Use only the lamp listed below or certified equivalents as failure to will result in non-compliance with federal regu-lations.

ACCELERATOR® VS-R™ Wolff® Model VAC75-T12-160W VS-R Bi-PinACCELERATOR® VHO Wolff® Model ACC75-T12-160W VHO PREHEAT BI-PIN

Provided eyeshields (Lucas Products Super Sunnies or Intrexco No. 5635/1) or equivalent eyewear as defined under21 CFR 1040.20. Other types of eyewear may not provide adequate protection. Disconnect power beforeattempting to clean, relamp, or engage in the maintenance of this product.

THIS EQUIPMENT MUST BE EARTH GROUNDED. THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDSFOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040.20

afety Informations

DA

R E C O M M E N D E D E X P O S U R E T I M E S I N M I N U T E SM A X I M U ME X P O S U R E T I M E I S 1 0M I N U T E SSkin Type: Week # Week 1 Week 2 Week 3 Week 4 Subsequent

nstallationI

1

Tools Required

You will need the following tools toassemble your booth:

Knife (Utility or similar)

#2 Phillips Screw Driver

Adjustable Wrench

Unpacking and Inspection

When removing the unit from its carton,always have two people available tohelp. We suggest having a moving dollyavailable to facilitate moving the unitinto place.

After unpacking the unit, inspect it forany visible damage. Report the extent ofany damage to the transportation com-pany. Also, within the same package youfound this manual you should have alsoreceived a pair of goggles, the outsidedoor handles (to be installed later), ahardware packet and a complimentarystart-up kit.

Record the serial number of the booth inthe area provided on the back of thismanual. This information will be requiredwhenever you call customer service.

1/2” Wrench

2

Installation-Pre-Installation Planning

Pre-Installation Planning

Before you begin to assemble your booth, you should observe the following pre-installation considerations.

• Your booth operates from a 220V ACsource. The unit must be hardwiredto a dedicated circuit capable of pro-viding 60 amp service. Electricalconnection of this unit requires aprofessional electrician.

• IMPORTANT! Use of a voltage sourceabove 230V AC may prevent properoperation of the booth and couldcause damage and void the warranty.

• Make sure the room in which youintend to use your booth is well venti-lated. Air from the room is used to coolthe booth, and a poorly ventilatedroom may cause the unit to becomehot and cause discomfort to the user.

• Your sunbed is designed to operate inan ambient room temperature of 80°Fmaximum and 70% relative humidity.

• The SUNVISION® Super V6000 mustbe installed in a room with a mini-mum ceiling height of eight (8) feet.Place your booth no closer than 6"from any wall.

• Proper assembly of your boothrequires three people. Plan to have acouple of helpers assist you.

3

Assembly

1. Each of the unit’s halves should beplaced together at the desired installa-tion location. Align the holes (A), locat-ed at the top and bottom of the unit.You will need both wrenches for thenext step.

Installation-Assembly

2. Secure the two halves of the unit toone another using the four 5/16x3/4”Hex Head bolts (B) and four lock nuts(C). Do not tighten them fully at thistime. NOTE: You may only be able toinstall three of the four bolts with theshipping brackets in place.

3. Remove the two shipping brackets,located on the top of the booth, whichconnect the doors to the rear of theframe.

B

A C

4. Lower all six of the leveling posts (A) until theweight is almost completely removed from thecasters (B). Check the doors to see if the tops ofthe doors are level with each other when closed,it may be necessary to further adjust the levelers.After the unit is level tighten the nuts left loosefrom Step 1. If necessary adjust the casters underthe doors (C). The door casters should bear onlythe weight of the doors. When properly adjustedthe doors will open and close easily. There shouldbe no gap between the doors when closed.

5. Connect the electrical cable at the rear top of theunit. Slide the black split grommet (D) found in theaccessory kit around the wire assembly and thenpress the grommet into slot (E). Now mount thewhite metal cap (F) cover over the connection withtwo #8x5/16” Phillips screws. Be careful not tocrimp, bind or pinch any of the wires.

Installation-Assembly

6. Attach the exterior handles to the doorsusing the pre-installed screws (G).

4

A

B

C

C

E

D

F

G

device. The remote control is optional.If you plan on using a remote systemrefer to “Remote Connections”.

CAUTION: Although the RemoteControl Bypass plug provided with yoursunbed will work wherever a T-Max®terminator is called for in the series,the T-Max® terminator will not work asa bypass plug. A bypass plug is neededonly when your sunbed is operatedwithout a remote system connected.

The booth is equipped with two 8Ωspeakers for your listening plea-

sure, capable of handling10W. Connect them to

an external amplifierusing the spring con-

nectors (C) located atthe top of the booth.

5

Bypass Plug

Connect the remote control bypass plug(A) to the remote control port (B) on topof your booth. The bypass plug can beinserted into either port. Your booth willnot operate without the bypass plug or aremote system connected.

NOTE: Your sunbed is designed toaccept an input from a remote control

Installation- Bypass Plug

7. Place the black, fan pedestal insidethe unit oriented so that the side with-out the air register is toward thefront. Connect the pedestalpower plug to the receptaclelocated underneath the rearcorner of the booth, next to themain power cord.

B

6

Remote Connections

Your booth incorporates advanced circuitryallowing it to connect and communicate withmost remote control systems. If a remote sys-tem is to be used, first determine whether theremote system is a T-Max® System or a stan-dard remote system operating with a controlrelay. Follow the appropriate instructions foryour system type.

Warning: The remote connection is notdesigned to supply or accept high voltage,nor can it provide power to an external timer.The booth’s remote interface circuitry oper-ates on 5 volts, attempting to connect it toany higher voltages will damage the booth aswell as void your warranty.

T-Max® Manager Remote SystemThe T-Max® Manager remote system offersthe ultimate in solarium control, while allow-ing the tanner easy straightforward operation.This system is ideal for multiple unit installa-tions. Your booth is already configured todirectly connect to this system. The circuitryinside your booth eliminates the need for theT-Max® 1A when connecting to the T-Max®

Manager series. To connect your booth to thissystem follow the instructions that came withyour remote system, noting figure 2 on thenext page. After you have set the address, or“id” of each solarium, simply connect the RJ-22 Modular cable(s), described in the T-Max®

Manager manual, directly into the port(s)located on the back of your booth. You canplace your booth at any location in the series.Remember the last connection in the seriesrequires a T-Max® terminator plug or SUNVI-SIONTM bypass plug.

Installation–Remote Connections

T-Max® 1A Remote SystemThe T-Max® 1A offers the same control as theT-Max® Manager in single booth installations.For this, your 1A must be configured as a“master”. If the 1A is not configured as a mas-ter it will not work in this application.

After you have set the address, or “id”, on theT-Max® 1A and the booth simply connect theRJ-22 modular cables, described in the T-Max® user’s guide, directly into either portlocated on the top of the booth and eitherport on the back of the T-Max® 1A. If the T-Max® 1A and the booth are more than 100feet apart, terminators or SUNVISION®

Remote Bypass plugs should be installed inthe unused ports. See figure 1.

Setting the addressBefore connecting your booth to the T-Max®

Manager or T-Max® 1A, the address or “id” ofyour booth must first be set. The auto-addressing feature of the latest T-Max®

Manager models is not compatible with thisbooth. Set the “id” manually as describedbelow.

Setting the “id”

1. Verify that the booth display is indicat-ing a “0”.

2. Press and hold the stop button locatedon the booth display for three secondsand release. The display should indi-cate an “id” number from 1 to 99.

3. If you are using a T-Max® 1A as yourremote the “id” of the booth must beset to “1”. If you are using a T-Max®

Manager each solarium must beassigned a different “id”. To set the“id” press the timer button until thedesired number is achieved.

7

4. Press the stop button to return to thenormal display mode.

5. If you are using a T-Max® 1A its “id”must be set to “0.0”. See your 1A man-ual for instructions. Also refer to your T-Max® 1A or Manager manuals to setother functions such as delay time andnumber of solariums in the T-Max®

Manager series.

Installation–Remote Connections

Remote systems using a Control Relay

Most non-T-Max® remote systems control thebooth by the use of a relay. The relay oper-ates the booth by connecting and discon-necting a pair of wires leading from the booth.Refer to the user’s manual provided with yourremote system to determine if it operates inthis way. To connect your booth to this typeof system a remote interface kit is required.Call ETS at the phone number listed on theback of this guide to obtain the kit. Figure 3below details a typical connection. Follow theinstructions provided with the kit and fromthe remote’s manual to make the necessaryconnections.

If you have questions consult theTroubleshooting guide in this manual or callETS at the phone number listed on the backof this guide.

Figure 3

Figure 2

Figure 1

8

Before You Tan

Before using your booth, please note thefollowing important precautions:

• WARNING your booth is designed forindividual use. Only one pair of pro-tective goggles is provided. Alwayswear these or another approved pairof goggles. Regular sunglasses do notprovide adequate protection fromultraviolet light. You should neverlook at the lamps when turned onwithout wearing the appropriate pro-tective goggles.

• Some medication may increase yoursensitivity to ultraviolet light. It is rec-ommended that you consult a physi-cian before using this booth if takingany medication or if you suspect thatyour skin might be especially sensitiveto sunlight. Included with this manualis an FDA booklet on medications thatincrease sensitivity to light.

• As with all electrical appliances, donot operate this device near wateror while you are wet.

perationOExposure Times

We recommend that you tan every otherday, following the tanning times in theexposure schedule. Tanning normallyappears after the first few sessions andmaximizes after approximately fourweeks. Tan once or twice per week there-after to maintain appearance. Personsalready having a base tan may begin atadvanced levels corresponding to theextent of their base tan.

Follow the guidelines for skin type andexposure times as shown in the tablebelow.

RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 10 MINUTESSkin Type: Week # Week 1 Week 2 Week 3 Week 4 Subsequent

Session # 1st-3rd 4th-6th 7th-10th 11th-13th MaximumI Sensitive Skin (Burns easily and severely and does not tan.) NOT RECOMMENDED FOR TANNINGII Light (Burns easily and severely and tans minimally.) 2 4 6 8 10III Normal (Burns moderately and tans average.) 3 5 7 10 10IV Dark (Burns minimally, tans easily and above average.) 4 6 8 10 10

9

Operation-Using Your Booth

Using Your BoothWhen connected to the T-Max® Manager or T-Max® 1A

1. Enter the booth and shut the doors behindyou. Center yourself on the pedestal foreven tanning.

2. Assuming the remote system has been set toallow a pre-tanning delay time, the timerdisplay (C) will repeatedly flash the delaysymbol “dL” and then the remaining delaytime. Press the timer button (E) or wait untilthe delay time has expired to begin the tan-ning session. The lamps and body fan willturn on and the timer will begin to countdown. If the timer did not display a “dL”, seeTroubleshooting.

3. If a tanning time less than the displayedtime is desired repeatedly press the timerbutton (E) to decrease the remaining time.

4. When the timer reaches 0 the lamps turnoff. If you want to stop your session beforetime expires press the stop button (D).

5. Exit the booth when the tanning session isover. The body fan runs for 3 minutes afterthe lamps shut off to aid in cooling thebooth. The timer will indicate “. .”, this isa reminder to clean the booth. After thebooth is cleaned press the timer button andthe display will return to “0”.

A Body fan control - Turns body fan on or off.

B Body fan indicator - Indicates fan opera-tion. (ON/OFF)

C Timer display - Displays remaining time.

D Stop button - Turns booth off.

E Timer button - Turns booth on. Timer dis-play shows remaining time. If a lessertime is desired, repeatedly press timerbutton until desired time is displayed.

A B C D E

10

Operation-Using Your Booth

Using Your BoothWhen configured as a stand alone unit orwhen connected to a remote system using acontrol relay.

If your booth is connected to a T-Max®

Manager remote system, see Using YourBooth When connected to the T-Max®

Manager, previous page.

A B C D E

1. Enter the booth and shut the doors behindyou. Center yourself on the pedestal foreven tanning.

2. Start the booth by pressing the timer button(E), located at the top of the canopy. Thelamps and body fan will turn on and thetimer display (C) will indicate the sessiontime remaining. If less than the maximumtanning time is desired, repeatedly pressthe timer button (E) until the desired time isindicated.

3. When the timer reaches 0, the lamps willturn off. If you want to stop your sessionbefore time expires press the stop button(D). The timer will then allow you ten sec-onds to reactivate the booth with theunused time. After ten seconds the timersystem resets back to 0 minutes.

4. Exit the booth when the tanning session isover. The cooling fans run for 3 minutesafter the lamps shut off to aid in cooling thebooth.

A Body fan control - Turns body fan on or off.

B Body fan indicator - Indicates fan opera-tion. (ON/OFF)

C Timer display - Displays remaining time.

D Stop button - Turns booth off.

E Timer button - Turns booth on. Timer dis-play shows remaining time. If a lessertime is desired, repeatedly press timerbutton until desired time is displayed.

11

Introduction

Your tanning booth has an hour meterwhich keeps track of how many hours thebooth has been in operation. Use thismeter to determine when your boothrequires maintenance.

Cleaning After Use

Clean and disinfect your tanning booth’spedestal, handles, control console and wiregrid after each use. Use a non-abrasive dis-infectant cleaner. We recommendSunQuest® disinfectant. Spray a clean softcloth with disinfectant and then clean allsurfaces that the tanner may have come incontact with.

Thorough Periodic Cleaning

Introduction

The cooling fans draw air through thebooth and over time will cause a dustbuildup on the lamps and reflectors. Thiswill reduce the tanning effectiveness of thebooth. When a dust buildup is observed, itis necessary to thoroughly clean the insideof the booth. Warning! Disconnect booth from electricalpower before cleaning.

are & MaintenanceCCleaning the Booth

Step 1. Remove the wire grids and lampsas described in Replacing Lamps.

Step 2. With a soft cloth, wipe the entirelength of each lamp and reflectorto remove any film buildup.

Step 3. Re-install the lamps and wire gridsas described in Replacing Lamps.

Mechanical Inspection

Your tanning booth has been built for yearsof service. To ensure trouble free operationthroughout its life, inspect the unit’smechanical integrity every 400-500 hoursof use.

• Inspect the unit’s fasteners verifyingthat all are firmly in place. Pay particu-lar attention to the door alignment.Adjust the door casters as needed. SeeAssembly Step 2.

• Inspect the AC power cable and its con-nections.

12

Replacing Lamps

To be assured of maximum tanning effec-tiveness, change lamps after approxi-mately 800-1000 hours of use. Tanningwill continue after this time but at a slow-er rate. To ensure trouble-free operationof your sunbed, replace the lamp starterswhenever the lamps are replaced.

Warning! Disconnect the booth fromelectrical power before servicing.

Removing/Replacing Wire GridsThe wire grids in the booth are secured inplace by screws. Remove these screws,located at the top of the grid, and lift thegrid out of its lower slot. The inside han-dle on the door must also be removedbefore removing the door grid. Simplyunscrew the handle from the handlebracket as shown. After changing lamps,replace the grids, handles and screws.When replacing the door grid, be sure toposition the grid behind the retaining pinon the handle bracket to limit movement.

Removing/Replacing LampsAfter grids are removed, replace lamps asfollows:Step 1. Grasp the lamp at one end and

at the middle, then turn thelamp a quarter turn. The lampmay then be gently removedfrom its holder.

Step 2. To re-install a lamp, insert thepins located on the ends of thelamp into the slots on top of thelamp holder and turn the lamp aquarter turn.

Recommended Replacement Lamps

We recommend using the lamps speci-fied below. Use of uncertified lamps is aviolation of federal regulations and willvoid your warranty. These lamps have anaverage life of 800-1000 hours of effec-tive tanning use. Lamps used longer thanthat begin to lose their effectiveness eventhough they will continue to light.

Only the following lamp type has beencertified for use in your SUNVISION®

booth:

ACCELERATOR® VS-R™ Wolff®

Model VAC75-T12-160W VS-R Bi-Pin

ACCELERATOR® VHO Wolff®

Model ACC75-T12-160W VHO PREHEAT BI-PIN

Care & Maintenance-Replacing Lamps

13

Booth not tanning

Lamps fail to light and timerdisplay is blank

Timer display changes to indi-cate a tanning time after thetimer button is pressed butlamps do not come on

My booth is connected to theT-Max® Manager remote sys-tem and when the delay timehas expired the timer displaystarts counting down but thebed lights do not come on

My booth won’t work withthe T-max® Manager remotesystems

Timer display continues toshow a 0 after the timer but-ton is pressed

The last minute of tanningtime does not count downfrom 59 seconds, but sometime less than 59 seconds

SolutionProblem

1. Clean booth, see Thorough Periodic Cleaning.2. Ensure supply voltage is between 208 and 230V AC.3. Replace lamps if lamp hours are greater than 800hrs.

1. Make sure the unit is connected to a power source.2. Check source of AC power. Reset circuit breaker or

replace fuse.

1. Bypass plug is not installed see Bypass Plug.2. A non-SUNVISION® bypass has been used. See Bypass

Plug.3. If remote is being used, other than T-Max® Manager,

the external timer may not be activated, or...4. remote wiring is incorrect, see the instructions provid-

ed with the remote interface kit.

The auto start feature of the remote system is disabled,see the instructions provided with your remote system.

1. The booth must first be set to a unique address seeRemote Connections.

2. The bypass or terminator plug may be installed in theseries in an inappropriate location. Plug the bypassplug only into the unit at the end of the series.

1. T-Max® Manager remote system has not yet been set. 2. booth address is not set correctly see Remote

Connections.

If the timer button has been pressed to decrease tan-ning time during the session, the time expired in thecurrent minute is subtracted from the last minute.

roubleshootingT

14

Troubleshooting-Problem/Solution Chart

One or more lamps fail to light

My bed is connected to a T-Max® remote system but I amhaving trouble getting into “id”mode.

My bed, connected to a T-Max® Manager, did not display“dL” but does indicate:

“0”.

a tanning time and thelamps have come on.

a tanning time but thelamps have not come on.

Timer display is indicating Er 1






SolutionProblem

1. Check that lamp is installed correctly.2. Switch unlit lamp with a lamp that lights, if new lamp

lights and old lamp still does not, replace old lamp.

You have probably attempted to connect your sunbedto the remote system already. Disconnect the remoteplug(s) from the ports at the back of the sunbed, wait90 seconds and try again.

1. Remote device has not been set.2. The sunbed has not been connected to the remote

system, see Remote Connections.

1. Delay time of T-Max® Manager has not been set.2. Delay time has expired and session has begun.

Auto start function of T-Max® Manager has beenturned off. Press the timer button to turn on lamps

Body lamps are on when they should be off, haveservice technician check the contactor.

Body lamps are off when they should be on, haveservicer check contactor and its wiring from the maintimer box.

Bench lamps are on when they should be off, haveservice technician check the contactor.

Bench lamps are off when they should be on, haveservice technician check the contactor and its wiringfrom the main timer box.

Not currently used

Not currently used










Face Tanner contactor is closed when it should beopen, have service technician check the contactor.

Face Tanner contactor is open when it should beclosed, have service technician check the contactorand its wiring from the main timer box.

Ballast Drawer is open or drawer switch is broken.

Timer computer is in an illegal state, reset power tocorrect, replace main timer if error reoccurs.




The timer display is not responding;1. Check cable to display.2. Replace display assembly.3. Replace main timer box.


SolutionProblem

Troubleshooting-Problem/Solution Chart

15

CALL FOR SERVICE ORQUESTIONS:

1•800•228•6292

6270 Corporate DriveIndianapolis, IN 46278-2900

Have the following information readywhen calling ETS to order parts or service

for your bed:

Date PurchasedCanopy Serial Number Bench Serial Number

models super v6000 vho super v6000 vs-r™tanning-bed-parts.com/documents/ets tan documentati… ·...

Documents