model u421/u444 owner's manualstoelting.us/pdfs/floorpressurefed/u421g owner's...

45
Model U421/U444 (Serial #17978 and up) OWNER'S MANUAL Manual No. 513595-4 Feb. 2009 Rev. 4

Upload: others

Post on 07-Sep-2020

5 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

Model U421/U444(Serial #17978 and up)

OWNER'S MANUALManual No. 513595-4 Feb. 2009 Rev. 4

Page 2: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496
Page 3: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

Need Parts or Service?

We stock the parts you need.Our Technicians are factorytrained and are certified in theStoelting Technicare program.

Model No.: _______________________Serial No.: _______________________Purchase Date: ____________________Start-Up Date:____________________

CALLDistributor: _________________________Phone No.: _________________________ (fill in or affix label)

Page 4: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496
Page 5: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

STOELTING, LLC Tele: 920-894-2293502 Hwy 67Kiel, WI 53042-1600 Fax: 920-894-7029

STOELTING® OWNER'S MANUALFOR

MODEL U421/U444CAB MODEL SOFT-SERVE PRESSURIZED FREEZER

This manual provides basic information about the freezer. Instructions and suggestions are givencovering its basic operation and care.

The illustrations and specifications are not binding in detail. We reserve the right to make changesat any time without notice, to the freezer and its components, without incurring any obligation tomodify or provide new parts for freezers built prior to date of change.

DO NOT ATTEMPT to operate the freezer until instructions and safety precautions in this manualare read completely and are thoroughly understood. If problems develop or questions arise inconnection with installation, operation or servicing of the freezer, contact the company at thelocation listed below.

Page 6: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496
Page 7: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

Section 1 .............................................................................................................. 1

1.1 Description .............................................................................................. 11.2 Specifications.......................................................................................... 2

Section 2 .............................................................................................................. 32.1 Safety Precautions .................................................................................. 32.2 Shipment & Transit .................................................................................. 42.3 Freezer Installation ................................................................................... 42.4 Installing Permanent Wiring ...................................................................... 42.5 Mix Pump ................................................................................................ 5

Section 3 .............................................................................................................. 93.1 Safety Precautions .................................................................................. 93.2 Operating Controls and Indicators ............................................................ 93.3 Important Information Regarding Cleaning and Sanitizing......................... 113.4 Disassembly of Freezer Parts.................................................................. 123.5 Cleaning Disassembled Parts ................................................................. 133.6 Sanitize Freezer Parts ............................................................................. 133.7 Cleaning the Freezer ............................................................................... 143.8 Assembling the Freezer ........................................................................... 143.9 Sanitizing ................................................................................................ 163.10 Initial Freeze down and Operation ............................................................ 163.11 Mix Information ........................................................................................ 173.12 Operation of Mix Pump ............................................................................ 183.13 Mix Pump Cleaning ................................................................................. 183.14 Disassembly and Inspection of Removable Parts ..................................... 18

Section 4 .............................................................................................................. 214.1 Freezer Adjustment ................................................................................. 214.2 Product Temperature Adjustment ............................................................. 214.3 Overrun Adjustment ................................................................................. 214.4 Mix Pump Hose Reposition ..................................................................... 224.5 Mix Pump Hose Replacement.................................................................. 224.6 Cab Temp. Adjustment............................................................................. 224.7 Drive Belt Tension Adjustment.................................................................. 224.8 Condenser Cleaning (Air Cooled Freezers) ............................................. 234.9 Preventative Maintenance ........................................................................ 234.10 Extended Storage ................................................................................... 234.11 Troubleshooting ....................................................................................... 24

Section 5 .............................................................................................................. 295.1 How to Order Replacement Parts ............................................................ 295.2 Parts Lists and Reference Drawings ........................................................ 29

TABLE OF CONTENTS

Page 8: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

ILLUSTRATIONS

Figure 1 Model U421/U444 Series Freezer .........................................1

Figure 2a Air-Cooled Specifications ......................................................2

Figure 2b Water-Cooled Specifications .................................................2

Figure 3 Decal Locations .....................................................................3

Figure 4 Water/Electrical Connections .................................................4

Figure 5 Auger Rotation .......................................................................5

Figure 6 Mix Hose Installation...............................................................5

Figure 7 Mix Pump...............................................................................6

Figure 8 3-way Tee ..............................................................................7

Figure 9 Mix Inlet Tube & Probe Assy. Clip...........................................7

Figure 10 Hose Holder...........................................................................7

Figure 11 Operating Controls .................................................................9

Figure 12 Auger Flight Wear & Front Auger Support Bushing Wear .......12

Figure 13 Front Door Disassembly ........................................................13

Figure 14 Auger Flight Removal .............................................................13

Figure 15 Rear Seal Removal ................................................................13

Figure 16 Rear Seal Lubrication ............................................................14

Figure 17 Spring Installation ...................................................................14

Figure 18 Front Door Assembly .............................................................15

Figure 19 Air Bleed Valves ....................................................................16

Figure 20 Draining Sanitizer ..................................................................16

Figure 21 Refrigerated Cabinet .............................................................17

Figure 22 Mix Pumps .............................................................................18

Figure 23 Removable Parts ...................................................................19

Figure 24 Cleaning Air Tube ..................................................................19

Figure 25 Cleaning Feed Tube ..............................................................19

Figure 26 Mix Pump Tube Routing .........................................................19

Figure 27 Potentiometer ........................................................................21

Figure 28 Overrun Adjustment ................................................................21

Figure 29 Temperature Control Cab ......................................................22

Figure 30 Belt Adjustment ......................................................................23

Page 9: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

Safety Alert Symbol:This symbol Indicates danger, warning or caution.Attention is required in order to avoid serious personalinjury. The message that follows the symbol containsimportant information about safety.

Signal Word:Signal words are distinctive words used throughoutthis manual that alert the reader to the existence andrelative degree of a hazard.

CAUTIONThe signal word “CAUTION” indicates a potentiallyhazardous situation, which, if not avoided, may resultin minor or moderate injury and equipment/propertydamage.

A Few Words About Safety

Safety Information Read and understand the entire manual beforeoperating or maintaining Stoelting equipment.

This Owner's Manual provides the operator withinformation for the safe operation and maintenance ofStoelting equipment. As with any machine, there arehazards associated with their operation. For thisreason safety is emphasized throughout the manual.To highlight specific safety information, the followingsafety definitions are provided to assist the reader.

The purpose of safety symbols is to attract yourattention to possible dangers. The safety symbols,and their explanations, deserve your careful attentionand understanding. The safety warnings do not bythemselves eliminate any danger. The instructions orwarnings they give are not substitutes for properaccident prevention measures.

If you need to replace a part, use genuine Stoeltingparts with the correct part number or an equivalentpart. We strongly recommend that you do not usereplacement parts of inferior quality.

WARNINGThe signal word “WARNING” indicates a potentiallyhazardous situation, which, if not avoided, may resultin death or serious injury and equipment/propertydamage.

CAUTIONThe signal word “CAUTION” not preceded by the safetyalert symbol indicates a potentially hazardous situa-tion, which, if not avoided, may result in equipment/property damage.

NOTICEThe signal word “NOTICE” indicates information orprocedures that relate directly or indirectly to thesafety or personnel or equipment/property.

Page 10: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496
Page 11: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

1

SECTION 1INTRODUCTION

1.1 DESCRIPTIONThe Stoelting U421 and U444 floor model freezers are pres-sure fed. The freezers are equipped with fully automaticcontrols to provide a uniform product. The U421 freezer isdesigned to operate with almost any type of commercialsoft serve. The U444 freezer is designed to dispense soft

Dimensionswidthheightdepth

WeightElectrical

left right left right left right left rightminimum circuit

ampacity 31A 31A 21A 21A 36A 31A 26A 21A

maximum overcurrent protection device 45A 45A 30A 30A 50A 45A 35A 30A

International Option

CompressorDrive Motor

Cooling

Hopper VolumeFreezing Cylinder

VolumeProduction

Capacity

48'' (121,9 cm)908 lbs (411,8 kg)

3 PH

U421/U431/U444 Water Cooled

760 lbs (344,7 kg)1 PH

78'' (198,1 cm)

Freezer26-3/4'' (67,9 cm)

U421/U431/U444 Air Cooled

Soft Serve - 18 GPH (68,14 liters)Shake - 27 GPH (102,21 liters)

Freezer26-3/4'' (67,9 cm)

with crate34'' (86,4 cm)

65-3/4'' (167,0 cm)39-3/4'' (101,0 cm)

Water cooled units require 1/2" N.P.T. water and drain fittings.

Air cooled units require 3" (7,6 cm) air space on right, 10" (25,4 cm) above.

Two - 8 gallon (30,28 liters)

Two - 1.33 gallon (5.32 quart), 5,4 liters

67-3/4'' (172,1 cm)39-3/4'' (101,0 cm)785 lbs (356,0 kg)

1 PH

with crate34'' (86,4 cm)78'' (198,1 cm)48'' (121,9 cm)

935 lbs (424,1 kg)3 PH

Two - 18,000 Btu/hrTwo - 2 hp

1 Phase, 220-240 VAC, 50Hz or 3 Phase, 380-415 VAC, 50Hz

serve product from the left side and shake product fromthe right side.

This manual is designed to assist qualified personnel andoperators in the installation, operation and maintenanceof the Stoelting Model U421 and U444 pressure freezer.

1.2 SPECIFICATIONS

Figure 1a. Model U421 Series Freezer

Soft Serve

Figure 1b. Model U444 Series Freezer

ShakeSoft Serve

Page 12: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

2

Figure 2a. Air-Cooled Specification

Figure 2b. Water Cooled Specification

Page 13: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

3

SECTION 2INSTALLATION INSTRUCTIONS

2.1 SAFETY PRECAUTIONSDo not attempt to operate the freezer until the safetyprecautions and operating instructions in this manual areread completely and are thoroughly understood.

Take notice of all warning labels on the freezer. The labelshave been put there to help maintain a safe workingenvironment. The labels have been designed to withstandwashing and cleaning. All labels must remain legible forthe life of the freezer. Labels should be checked periodi-cally to be sure they can be recognized as warning labels.

1 324722 Decal Mix Low2 324798 Decal Clean-Off-Serve Switch3 324141 Decal Caution - Rotating Blades4 723526 Tag Read Manual & All Decals6 324393 Decal Stoelting Swirl Logo7 324800 Decal Cab ON/OFF8 324799 Pump On/Off9 324208 Decal Refrig. Leak Check11 324103 Decal Caution - Rotating Shaft12 324686 Decal Danger Automatic Start13 324107 Decal Caution Moving Parts14 324125 Decal Elect.Shock Hazard15 324151 Decal Field Connections16 324198 Decal Attention Installer17 130000 Bag, Envelope Front Loading18 324584 Decal Adequate Ventilation19 324158 Decal Copper Conductors Only20 324106 Decal Caution Wiring Mat'l22 324566 Decal Wired According To

23 324015 Decal 2 x 1-1/4 Blk on White24 723552 Tag, Caution - Supply Voltage26 324803 Decal GM Header (Stoelting Logo)26 324804 Decal GM Header (Stoelting Swirl)26 324805 Decal DQ Header (DQ Logo)27 324346 Decal Caution Hazard.Moving28 324797 Decal Standby/Serve29 324242 Decal Temperature Control30 324200 Decal Manual Reset32 324014 Decal Arrow33 324496 Decal FreezingWater Cooled OnlyA 324065 Decal Water InletB 723525 Tag Winterizing Disconnect LineC 723517 Tag, W/C Tower InstructionsD 324107 Decal Caution Moving PartsAir Cooled OnlyE 324346 Decal Hazardous Moving PartsF 324107 Decal Caution Moving Parts

Figure 3. Decal Locations

If danger, warning or caution labels are needed, indicatethe part number, type of label, location of label, andquantity required along with your address and mail to:

STOELTING, LLCATTENTION: Customer Service

502 Hwy. 67Kiel, Wisconsin 53042

Page 14: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

4

2.2 SHIPMENT AND TRANSITThe freezer has been assembled, operated, and in-spected at the factory. Upon arrival at the final destina-tion, the freezer must be checked for any damage whichmay have occurred during final transit.

With the method of packaging used, the equipment shouldarrive in excellent condition. THE CARRIER IS RESPON-SIBLE FOR ALL DAMAGE IN TRANSIT, WHETHER VIS-IBLE OR CONCEALED. Do not pay the freight bill untilthe freezer has been checked for damage. Have the car-rier note any visible damage on the freight bill. If concealeddamage and/or shortage is found later advise the carrierwithin ten days and request inspection. The customermust place claim for damage and/or shortages in ship-ment with the carrier. Stoelting, LLC. cannot makeany claims against the carrier.

2.3 FREEZER INSTALLATION

WARNING

Installation must be performed by a qualified electri-cian/refrigeration specialist. Incorrect installation maycause personal injury, severe damage to the machineand will void factory warranties.

WARNING

Lifting hazardDo not attempt to lift freezer manually. Use proper lift-ing equipment such as a forklift, lift table, or palletjack, with lifting device positioned beneath the freezer’sbase. Ensure that personnel remain clear of suspendedload. Failure to do so may result in personal injuryand/or damage to the freezer that will void any factorywarranties.

Installation of the freezer involves moving the freezer closeto its permanent location, removing all crating, setting inplace, assembling parts, and cleaning.

A. Uncrate the freezer.

B. Install the four casters. Turn the threaded end intothe freezer until zero threads are showing. To level,turn out casters no more than 1/4" maximum, thentighten all jam nuts.

C. The freezer must be placed in a solid level position.

NOTEAccurate leveling is necessary for correct drainage offreezer barrel and to insure correct overrun.

Figure 4. Water/Electrical Connections

D. The freezer must have a minimum of 3" (7,5cm)-6" (15cm) high ambient conditions- of space on allsides and 10" (25cm) at the top for proper circula-tion.

CAUTION

Risk of product damageAir cooled condenser requires proper ventilation. Fail-ure to provide adequate ventilation will void factorywarranties.

E. Water-cooled freezers need an adequate watersupply. Install 1/2" (12,7mm) pipe or 1/2" (12,7mm)inside diameter copper water line to the freezer.Connect water outlet to a drain using a 1/2"(12,7mm) inside diameter line. Automatic washerhoses work well for final connections. All waterconnections must comply with local codes. Fig. 4.

CAUTION

Flush all water lines before installation. In stores withsediment in water, add suitable filter or strainer to waterinlet.

F. Place the CLEAN-OFF-SERVE switches in the OFFposition before continuing. Figure 11.

2.4 INSTALLING PERMANENT WIRINGPermanent wiring is required by local codes, the followingprocedure must be performed:

WARNING

Hazardous voltageHigh voltage will shock, burn or cause death. Turn offand lock out main power disconnect before installingwiring. Do not operate machine with cabinet panelsremoved.

Page 15: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

5

2.5 MIX PUMP

A. Mix Pump Hose InstallationFollow the steps below to install the mix pump hose.

1. Turn pump on.

2. Feed one end of mix pump hose into the entering orpick-up hose side (left) of black cover.

3. Gently push the hose into the black cover until itbegins to feed.

4. Allow the hose to feed itself thru the pump until 6"(15cm) remains on the entering side.

Figure 6. Mix Hose Installation

A. Refer to the nameplate at the rear of the freezer forspecific electrical requirements. Make sure thepower source in the building matches the freezernameplate requirements. Bring the wires into thejunction boxes through the access holes in thebottom rear of the freezer. Figure 4.

NOTICEThree phase freezers in areas of unbalancedelectrical loads require special attention whenconnecting input electrical power. The unbal-anced leg of power (called wild or high) must beconnected to L2 in the junction box.

NOTICEVerify actual voltage. Machine is equipped witha transformer to supply a control circuit. Youwill need to check voltage on terminal C1 andC2 on EACH control board. (Located behinddecorative header panel on front of machine.)Transformers are located behind electrical panelenclosing control boards. Access these by re-moving top panel of machine. Actual transformervoltage should read 20-28 V.A.C.

B. Remove the lower back panel and the two junc-tion box covers located at the bottom of thefreezer.

C. lnstall permanent wiring according to localcode.

D. Check the auger shaft rotation by placing theMAIN DRIVE switch in the CLEAN position.

Auger shaft rotation is clockwise as viewed through theclear plastic front door. If the rotation is not clockwise,turn main electrical power OFF. Then reverse L1 and L3electrical power lines to the junction box (three phaseonly). Re-check auger shaft rotation. Figure 5.

Figure 5. Auger Rotation

6" (15cm)

Page 16: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

6

B. Connect 1/2 inch (12,7mm) I.D. plastic food gradetubing to check valve and then to the mix con-tainer. Observe check valve flow arrow. Securewith hose clamps. Then place assembly thru holein cover and install retainer clip. Figure 9.

C. Connect 1/2 inch (12,7mm) I.D. plastic food gradetubing between the large port of air/mix tee andrefrigerated mix transfer line. Secure with largehose clamp or equivalent. Figure 9.

CAUTION

Air/Mix tee must remain below the black cover/clamp. If the tee is above the pump mix willdrain to the air compressor resulting in pumpdamage.

D. Connect mix low cords.

Figure 7. Mix Pump

5.Turn pump off.

6.Connect mix pump hose to pickup hoseadapter using small hose clamp.

CAUTION

DO NOT TWIST MIX PUMP HOSE.

7.Turn pump off.

8.Allow remaining 6" (15cm) of tubing to feedthrough pump until hose adapter prevents furtherfeeding.

9.Turn pump off.

10.Connect free end of mix pump hose to 3-way Tee

264241

376041

756088

694247

762256756088

1151965

696130

1172864

375867

756088

756204

756067

Page 17: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

7

Figure 8. 3-way Tee

Figure 9. Mix Inlet Tube & Probe Assy. Clip

RefrigeratedMix Transfer

Line

Large Port(Air/Mix)

3-way Tee

Low Mix Cord

Cover

RetainerClip

MixContainer

Hose Holder

Figure 10. Hose Holder

Page 18: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

8

Page 19: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

9

SECTION 3INITIAL SET-UP AND OPERATION

3.1 SAFETY PRECAUTIONSSAFE OPERATION IS NO ACCIDENT; observe theserules:

A. Know the freezer. Read and understand the operat-ing instructions.

B. Notice all warning labels on the freezer.

C. Wear proper clothing. Avoid loose fitting garments,and remove watches, rings or jewelry which couldcause a serious accident.

D. Maintain a clean work area. Avoid accidents bycleaning the area and keeping it clean.

E. Stay alert at all times. Know which switch, pushbutton or control you are about to use and whateffect it is going to have.

F. Disconnect electrical power for maintenance.Never attempt to repair or perform maintenance onthe freezer until the main electrical power has beendisconnected.

G. Do not operate under unsafe operating condi-tions. Never operate this freezer if unusual or exces-sive noise or vibration occurs.

Figure 11. Operating Controls

3.2 OPERATING CONTROLS AND INDICATORSBefore operating the freezer, it is required that the op-erator know the function of each operating control. Referto Fig.11 for the location of the operating controls on thefreezer.

WARNINGHazardous voltageThe CLEAN-OFF-ON switch must be placed in the OFFposition when disassembling for cleaning or servicing.The freezer must be disconnected from electricalsupply before removing any access panel. Failure todisconnect power before servicing could result indeath or serious injury.

A. Spigot SwitchWhen the spigot handle is opened the SPIGOTswitch will start the auger drive and refrigerationsystems. When the spigot handle is closed, the drivemotor and compressor will remain on until the productin the barrel reaches the proper temperature.

B. Clean-Off-Serve SwitchThe CLEAN-OFF-SERVE switch is a three positiontoggle switch used to control the operation of therefrigeration system and auger. When the switch isplaced in the CLEAN position, the refrigeration sys-tem will be off and auger will rotate for cleaning.

Page 20: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

10

When the switch is placed in the OFF position, therefrigeration system and auger will not operate.

When the switch is placed in the SERVE position,the refrigeration system and auger will operate auto-matically. The switch should be placed in the SERVEposition for normal operation.

C. Cabinet-Off-On SwitchThe CABINET-OFF-ON switch is a two positiontoggle switch. When the switch is placed in the OFFposition, the lower cabinet refrigeration system willnot run. When the switch is placed in the ONposition, the lower cabinet refrigeration system willrun until the preset temperature is reached; thencycle ON and OFF to maintain that temperature.

D. Cab Indicator LightA flashing light indicates the cab OFF-ON switch isin the OFF position, no refrigeration. Place the OFF-ON switch in the ON position for cab refrigeration.

E. Pump SwitchThe pump motor switch is a two position toggleswitch. When the switch is placed in the OFFposition, the pump will not run. When the switch isplaced in the ON position, the pump will run until thepreset pressure is reached, then cycle ON and OFFas product is drawn to maintain that pressure.

F. Standby/Serve SwitchThe standby/serve switch is a two position toggleswitch. When the switch is placed in the standbyposition the freezer will cycle to maintain a tempera-ture below 41°F (-15°C). When the switch is in theServe position the freezer will cycle to maintain aservable product.

G. Freezing SwitchThe freezing switch is a two position toggleswitch. When the switch is placed in the MAXIMUMposition the freezer will be forced to run 30 secondsafter the temperature control is satisfied.

H. High Head Pressure Cut OutIf the head pressure exceeds 445 psig (28 bar) aircooled andwater cooled, the high head pressurecutout will trip. The reset button can be accessedfrom the side of the freezer.

I. Low Mix LightThe low mix light will illuminate when the liquid levelin the mix container drops below two gallons.

J. Front Door Safety SwitchThe front door safety switch prevents the auger fromturning when the front door is removed. The switchis open when the door is removed and closed whenthe door is properly installed.

Page 21: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

11

3.3 IMPORTANT INFORMATION REGARDINGCLEANING AND SANITIZINGSoft serve and shake freezers require specialconsideration when it comes to food safety andproper cleaning and sanitizing.

The following information specifically covers issuesfor cleaning and sanitizing frozen dessert freezers.This information is meant to supplement acomprehensive food safety program.

Soil Materials Associated with Frozen DessertMachines

MILKFAT/BUTTERFAT – As components of ice-cream/frozen custard mix, these soils willaccumulate on the interior surfaces of the machineand its parts. Fats are difficult to remove and helpattribute to milkstone build-up.

MILKSTONE – Is a white/gray film that forms onequipment and utensils that come in contact withdairy products. These films will accumulate slowlyon surfaces because of ineffective cleaning, use ofhard water, or both. Milkstone is usually a porousdeposit, which will harbor microbialcontaminants and eventually defy sanitizingefforts.

Once milkstone has formed, it is very difficult toremove. Without using the correct product andprocedure, it is nearly impossible to remove a thicklayer of milkstone.(NOTE: general-purpose cleaners DO NOT removemilkstone.) This can lead to high bacteria countsand a food safety dilemma.

IT IS BEST TO CONTROL MILKSTONE ON ADAILY BASIS BEFORE IT CAN BECOME ASIGNIFICANT FOOD SAFETY PROBLEM.

In addition to food safety, milkstone can causepremature wear to machine parts which can add tocosts for replacement parts or possibly moreexpensive repairs if worn machine parts are notreplaced once they have become excessively worn.

Important Differences Between Cleaning andSanitizing

CLEANING vs. SANITIZINGIt is important to distinguish between cleaning andsanitizing. Although these terms may soundsynonymous, they are not. BOTH are required foradequate food safety and proper machinemaintenance.

CLEANING· Is the removal of soil materials from a surface.· Is a prerequisite for effective sanitizing.

NOTEAn UNCLEAN surface will harbor bacteria that candefy sanitizing efforts.

Bacteria can develop and resist sanitizing effortswithin a layer of soil material (milkstone). Thoroughcleaning procedures that involve milkstoneremoval are critical for operators of frozendessert machines.

SANITIZING· Kills bacteria.· Can be effective on clean surfaces only.· DOES NOT clean or remove milkstone.

NOTEUsing a SANTITIZER on an unclean surfacewill not guarantee a clean and safe frozendessert machine.

Proper Daily Maintenance:The Only Way to Assure Food Safety andProduct Quality

Proper daily maintenance can involve a wide varietyof products and procedures. Overall, the productsand procedures fall into three separate categories.(Please note that this is a brief overview intended forinformational purposes only.)1. CLEANING – This involves draining mix from the

freezer barrel and rinsing the machine withwater. Next, a cleaner is run through themachine. Then, the machine is disassembledand removable parts are taken to the sink forcleaning.

2. MILKSTONE REMOVAL – Since almost allcleaners do not have the ability to removemilkstone, the use of a delimer becomesnecessary. Although this procedure may not beneeded on a daily basis, it will usually follow thecleaning procedure. It requires letting a delimersolution soak in the machine for an extendedperiod of time. Individual parts are also soakedin a deliming solution for an extended period oftime (more about delimers in AdditionalInformation).

3. SANITIZING – After the machine has beencleaned and contains no milkstone, themachine is reassembled. Then a FDA-approvedsanitizing solution is run through the machine tokill bacteria. The machine is then ready for foodpreparation.

Page 22: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

12

As a recommended cleaner and sanitizer for yourfrozen dessert machine, STERA-SHEEN has provento be one of the best daily maintenance products for:

· CLEANING – Thorough removal of all solidsincluding butterfat and milk fat.

· MILKSTONE REMOVAL – Complete removal ofmilkstone.

· SANITIZING – FDA-approved no rinse sanitizerfor food contact surfaces.

Additional Information

THE USE OF DELIMERSA delimer is a strong acid that has the ability todissolve milkstone. This type of chemical maybecome necessary once high levels of milkstonehave developed. While these products are veryeffective for removing HIGH levels of milkstone, theyare not ideal for two reasons:

1. PRODUCT SAFETY – Strong acids aredangerous chemicals and handling themrequires safety

2. MACHINE DAMAGE – Strong acids will attackmetal and rubber causing premature wear ofparts. The use of a delimer needs to be closelymonitored to avoid damage to machine surfacesand parts.

With proper daily use of STERA-SHEEN or it’sequivalent, there is no need for the use of aDELIMER.

DO NOT USE BLEACH· BLEACH HAS ABSOLUTELY NO CLEANING

PROPERTIES.· BLEACH IS CORROSIVE. It can and will

damage components of the machine causingpremature wear and metal corrosion.

GENERAL PURPOSE CLEANERS

General purpose cleaners do not have the ability toremove milkstone. Milkstone will become a problemif not remedied with additional products andprocedures.

THE USE OF CHLORINE TEST STRIPS

“Test strips” are used to determine concentrations ofactive chlorine in sanitizing solutions. To use thestrips, tear off a small portion and submerge it intothe sanitizing solution. Then, compare the colorchange to the color key on the side of the test stripdispenser to determine the approximate chlorineconcentration.

The ideal concentration of chlorine needs to be 100ppm (as stated by the FDA).

NOTEFollow the directions on the container for properconcentration.

There are two main factors that contribute to fallingchlorine concentrations in a sanitizing solution.

1. PRODUCT USE – As the chlorine in thesolution is being used, chlorine concentrationsfall.

2. TIME – As time passes, small amounts ofchlorine “evaporate” from the solution. (That iswhy you can smell it.)

Sanitizing solutions should not be allowed to fallbelow 100 ppm chlorine. New solutions should bemixed once old solutions become ineffective.

Figure 12. Auger Flight Wear & Front AugerSupport Bushing Wear

Wear Line

Before using the freezer for the first time, complete freezerdisassembly, cleaning and sanitizing procedures will needto be followed. Routine cleaning intervals and proceduresmust comply with the local and state health codes.Inspection for worn or broken parts should be made atevery disassembly of the freezer for cleaning or otherpurposes. All worn or broken parts should be replaced toensure safety to both the operator and the customer andto maintain good freezer performance and a quality prod-uct. Two normal wear areas are the auger flights and frontauger support bushing (see Figure 12).

To disassemble the freezer, refer to the following steps:

3.4 DISASSEMBLY OF FREEZER PARTS

WARNING

Moving machinery can grab, mangle and dis-member. Place the CLEAN-OFF-SERVE toggleswitch in the OFF position before disassemblingfor cleaning or servicing. Placing the CLEAN-OFF-SERVE toggle switch in the SERVE position dur-ing cleaning or servicing may result in seriouspersonal injury.

Page 23: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

13

A. Disassembly Of Front Door

1. Remove the front door by turning off the blackknobs and then pulling the front door off the studs.

2. Remove the air bleed valve by unscrewing theknob while holding the valve stem from behind.Removethe compression spring and push airbleed valve through the rear of the front door.

3. Remove the spigot through the bottom of the frontdoor (see Figure 13). Remove all O-rings fromspigot and air bleed valve.

B. Disassembly Of Auger

1. Remove the front auger support by pulling itstraight out of the freezer barrel.

Figure 13. Front Door Disassembly

Figure 15. Rear Seal Removal

2. Remove the plastic bearing from the front augersupport.

3. Remove the auger by pulling slowly and rotatingout of the freezer barrel. As the auger iswithdrawn, remove each plastic flight and springfrom the auger. Be careful not to scratch inside offreezer barrel when removing flights or auger.Remove the spring from each auger flight.

4. Keep the rear of the auger tipped up once it isclear of the freezer barrel.

5. Wipe spline lubricant off hex end of auger with apaper towel. Remove the rear seal. Figure 15.

Figure 14. Auger Flight Removal

3.5 CLEANING DISASSEMBLED PARTSDisassembled freezer parts require complete cleaning,sanitizing and air drying before assembling. Local andstate health codes will dictate the procedure required.Some state health codes require a four sink process (pre-wash, wash, rinse, sanitize, air dry), while others requirea three sink process (without the pre-wash step). Thefollowing procedures are a general guideline only. Consultyour local and state health codes for procedures requiredin your location.

A. To clean the freezer parts, disassemble all parts.(Refer to section 3.4 for the disassembly of freezerparts.)

B. Place all front door and auger parts in clean 90° to110°F (32°C to 43°C) water and wash thoroughly(four sink procedure only).

C. Place all parts in 90° to 110°F (32°C to 43°C) , milddetergent water and wash thoroughly.

D. Rinse all parts with clean 90° to 110°F (32°C to43°C) water.

F. Sanitize all freezer parts following procedures outlined below.

3.6 SANITIZE FREEZER PARTSA. Use a sanitizer mixed according to manufacturer's

instructions to provide a 100 parts per million strengthsolution. Mix sanitizer in quantities of no less than 2gallons of 90° to 110°F (32°C to 43°C) water. Allowthe sanitizer to contact the surfaces to be sanitizedfor 5 minutes. Any sanitizer must be used only inaccordance with the manufacturer's instructions.

B. Place all parts in the sanitizing solution for 5 minutes,then remove and let air dry completely before assembling in freezer.

Page 24: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

14

3.7 CLEANING THE FREEZER

CAUTION

Risk of Product DamageDo not use acid cleaners, strong caustic compoundsor abrasive materials to clean any part of the freezerexterior or plastic parts.

The exterior should be kept clean at all times topreserve the lustre of the stainless steel. A goodgrade of stainless steel has been used on thefreezer to ease clean-up. To remove spilled or driedmix, simply wash the exterior in 90° to 110°F (32°Cto 43°C) , soapy water and wipe dry.

Do not use highly abrasive materials as they willmar the finish. A mild alkaline cleaner is recom-mended. Use a soft cloth or sponge to apply thecleaner. For best results, wipe in the direction of thegrain of the steel.

A. Clean the rear seal surface from inside of the freezerbarrel.

B. Using this sanitizing solution and the large barrelbrush provided, sanitize the barrel by dipping thebrush in the sanitizing solution and brushing theinside of the barrel.

C. Remove the rear drip tray by pulling from side panel.Clean and replace drip tray.

3.8 ASSEMBLING FREEZERTo assemble the freezer parts, refer to the following steps:

NOTICEPetro-Gel sanitary lubricant or equivalent must beused when lubrication of freezer parts is specified.

NOTICEThe United States Department of Agriculture andthe Food and Drug Administration require that lubri-cants used on food processing equipment be certi-fied for this use. Use Lubricants only in accordancewith the manufacturer's instructions.

Figure 17. Spring Installation

E. Install first flights to bottom of auger, rotate, addsuccessive flights from bottom as the auger is pushedslowly into the freezer barrel. Carefully engage augerwith drive socket in speed reducer by rotating augerslowly and pushing on end of auger.

F. Apply a thin film of sanitary lubricant to the inside andoutside of the front auger support bearing, then placeon the front of the auger. Assemble the front augersupport onto the auger bearing.

C. Lubricate the hex drive end of auger with a smallamount of white socket lubricant. A small containerof socket lubricant is shipped with the freezer.

D. Screw the springs onto the studs in plastic flights.Spring must be screwed into the flights com-pletely to provide proper tension (see Figure 17).

Figure 16. Rear Seal LubrciationLubricate with Petrogel

Lubricatewith

SocketLubricant

A. Assemble all O-rings onto parts dry, without lubri-cation. Then apply a thin film of sanitary lubricationto exposed surfaces of the O-rings.

B. Lubricate rear seal area on auger shaft with a thinlayer of sanitary lubricant. Install the rear seal O-ring.Lubricate outside of rear seal O-ring with sanitarylubricant.

C. Install stainless steel rear seal adapter into rear sealdry (without lubricant). Lubricate inside surface ofrear seal adapter and install onto auger shaft. DONOT lubricate outside of rear auger seal (see Figure16).

NOTICEPosition the front support on auger so legs do notinterfere with the pin on the back of the front doorassembly. Front door must push auger in slightlywhen it is being tightened to prevent the rear sealfrom leaking.

Page 25: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

15

H. Install the spigot through the bottom of the frontdoor ( see Figure 18).

Figure 18. Front Door Assembly

I. Assemble the air bleed valve O-ring onto the airbleed valves. Position the O-ring in groove close tothe wide part. Apply a thin film of sanitary lubricant tothe O-rings.

J. Insert the air bleed valve from the back of the frontdoor. Install compression springs onto air bleedvalves, then screw knobs on finger tight.

K. Apply a thin film of sanitary lubricant to the door sealO-rings, and fit into the grooves on the rear of thefront door.

L. Place the front door assembly on the mounting studsand push front door against the freezer carefully.

M. Secure front door assembly by placing the knobs onthe studs and tighten until finger tight only. Do notovertighten. ProperO-ring seal can be observedthrough the transparent front door.

N. Move the spigot handles to the closed position.

G. Assemble O-rings onto the spigot dry, withoutlubrication. Then apply a thin film of sanitary lubricantto the outside of the O-rings and spigot bodies.

Page 26: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

16

A. Prepare 3 gallons of sanitizing solution followingmanufacturer's instructions, and pour into storagecontainer.

B. Place the mix pump switch in the ON position andopen air bleed valve on the front door by pushingvalve in and holding (see Figure 19).

C. Let sanitizing solution fill the freezer barrel to air bleedvalve, then close the valve by pulling out to lock inplace.

D. Place the CLEAN-OFF-SERVE toggle switch inthe CLEAN position.

Figure 20. Draining Sanitizer

E. Check for leaks when the freezer barrel is firstpressurized with sanitizing solution.

1. Check for leaks at the plastic front door, theO-rings may not be sealed.

2. Check the drain located at the center of theDrip Tray for leaks coming from the rear of theRear Auger Seal.

3. Check inside cab unit for leaks at hose connec-tions.

F. Using a sanitized soft bristle brush or equivalent,dipped in sanitizing solution, clean mix container.

G. After five minutes, open spigot to expel sanitizingsolution. Drain all solution from freezer using bothspigots (See Figure 20).

H. Close the spigot and place the mix pump switchand the CLEAN-OFF-SERVE switch in the OFFposition.

The freezer is now sanitized and ready for adding mix.

3.10 INITIAL FREEZE DOWN AND OPERATIONThis section covers the recommended operating proce-dures to be followed for the safe operation of the freezer.

A. Sanitize just prior to use according to instructionsoutlined in this manual.

B. Prepare the desired amount of mix and then fill eachstorage container with approximately 3 gallons ormore of mix. Place a container(s) of mix in the re-frigerated cabinet. If drawing from a storage container,place the draw tube through the cover to the bottomof the container. If drawing from a bag in a box, re-move the cap, push out all of the air, and insert theadaptor.

3.9 SANITIZINGSanitizing must be done after the freezer is clean and justbefore the freezer is filled with mix. Sanitizing the nightbefore is not effective. However, you should always cleanthe freezer and parts after using it.

WARNING

The United States Department of Agriculture andthe Food and Drug Administration require thatall cleaning and sanitizing solutions used withfood processing equipment be certified for thisuse.

When sanitizing the freezer, refer to local sanitary regula-tions for applicable codes and recommended sanitizingproducts and procedures. The frequency of sanitizing mustcomply with local health regulations. Mix sanitizer ac-cording to manufacturer’s instructions to provide a 100parts per million strength solution. Mix sanitizer in quan-tities of no less than 2 gallons of 90°F to 110°F 90° to110°F (32°C to 43°C) water. Allow sanitizer to contact thesurfaces to be sanitized for 5 minutes. Any sanitizer mustbe used only in accordance with the manufacturer’s in-structions.

CAUTION

Risk of Product DamageAvoid prolonged contact of sanitizer with freezer parts.Prolonged contact of sanitizer with freezer may causecorrosion of stainless steel parts.

Figure 19. Air Bleed Valves

Air Bleed Valves

Page 27: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

17

The freezer is designed to dispense the product at areasonable draw rate. If the freezer is overdrawn, theresult will be a soft product and air pops. If this shouldoccur, allow the freezer to run for approximately 30seconds before dispensing additional product. After awhile the operator will sense or feel when the freezer isbeginning to fall behind, and will slow down on the rate ofdraw so as not to exceed the freezer's capacity.

Do not operate the freezer when the MIX LOW light ison or with less than 1-3/4" (4.4 cm) of mix in themix container. Refill the mix container immediately.

3.11 MIX INFORMATIONMix can vary considerably from one manufacturer toanother. Differences in the amount of butter-fat content andquantity and quality of other ingredients have a directbearing on the finished frozen product. A change in freezerperformance that cannot be explained by a technicalproblem may be related to the mix.

Proper product serving temperature varies from onemanufacturer's mix to another. Soft serve mixes shouldprovide a satisfactory product in the 17° to 20°F (-7° to-6°C) range. Most shake mixes freeze to proper consis-tency at 27°F (-2.8°C). Diet and low-carb mixes typicallyfreeze to proper consistency at higher temperatures.

When checking the temperature, stir the thermometer inthe frozen product to read the true temperature.

Mix does not improve with age. Old mix, or mix that hasbeen stored at too high a temperature, can result in afinished product that is less than satisfactory from theappearance and taste standpoint. To retard bacteriagrowth in dairy based mixes, the best storage temperaturerange is between 36° to 40°F (2.2° to 4.4° C).

C. Place the mix pump switch in the ON position. Immediately open the spigot and let approximately 8ounces of liquid mix with sanitizing solution drainout of the spigot.

D. Close the spigot and open the air bleed valve on thefront door by pushing the valve in and holding. Allowthe barrel to fill until the mix level is 1/2" (2.7 cm)below air bleed valve, then release valve and pullclosed to lock in place.

E. Start the compressor and drive by placing theCLEAN-OFF-SERVE switch in the SERVE position

F. The product will be ready to serve after the compres-sor and drive have cycled off, or in approximately 12minutes.

G. The refrigeration is automatically actuated when thespigot is opened. For normal dispensing, open thespigot no more then 90°. (This is when the handleknob is pointed directly away from the front door.)This position provides excellent control over the prod-uct and aids in making desired shaped portions.Close spigot completely after dispensing.

Figure 21. Refrigerated Cabinet

Mix LowSensor

Page 28: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

18

C. The over-run adjustment is preset at the factory. If anadjustment becomes necessary, refer to Section 4.

3.12 OPERATION OF MIX PUMPThe pump switch is located on the front of the freezer.When the pump switch is placed in the ON position, themix pump motor will be actuated to pump mix into thefreezer cylinder. When the set pressure is reached, themix pump will shut off automatically. When the switch isplaced in the OFF position, the mix pump will be inopera-tive.

NOTEThe mix pump motor is equipped with an internaloverload that will “trip”, disabling the pump when themotor is overloaded. Consult the trouble shootingsection for corrective information.The internal over-load will automatically reset after cooling. If the con-dition continues, contact a qualified service person.

CAUTION

Risk of Product DamageMix pump hose must be repositioned every 1 -2 weeksor 60 hours of operation. Failure to comply will resultin reduced mix pump liquid capacity, dispense stop-page, popping, and possible mix pump hose leak-age. Hose leakage may damage the pump roller as-sembly and void the factory warranty.

A. Mix Operation: The peristaltic mix pump containsone continuous mix pump hose. When looking at theface of the peristaltic mix pump, the left side of thehose is the suction or pickup. The right side of thehose is the discharge. Mix is drawn up the suctionside of the hose and transferred thru the dischargeside to the freezer (see Figure 22).

B. Air Operation: The air compressor operates wheneverthe peristaltic mix pump is running. Air enters thru acheck valve on the piston downstroke. The air isdischarged thru a second check valve, on the pistonupstroke. The air and mix join at the tee and thentravel to the freezer.

NOTICEAny cleaning procedure must always be followedby sanitizing before filling freezer with mix. (Refer tosection 3.3)

3.13 MIX PUMP CLEANINGThe mix pump is approved for CIP (clean in place) and isthoroughly cleaned as cleaning solutions are pumped thruthe freezer. We recommend completely disassemblingthe pump and connecting tubing every 14 days for inspectionof parts to confirm the CIP has been properly performed. Ifany residue is detected clean or replace those parts asoutlined below.

1. Place CLEAN-OFF-SERVE switch in CLEAN posi-tion. Allow the auger to agitate for 5 to 10 minutes.

2. Remove suction tube from mix container. Draw off themix remaining in freezer barrel.

3. Pump 2 gallons (7.5 liters) of cold potable water thrufreezer until water at spigot is free of mix.

4. Pump 2 gallons (7.5 liters) of 90° to 110°F (32°C to43°C) detergent solution water thru freezer. The useof soft water is recommended, along with dishwashingdetergents such as “Joy,” “Dawn,” or equivalent.

5. Place mix pump switch in OFF position. Open spigotto relieve remaining pressure.

6. Place CLEAN-OFF-SERVE switch in OFF position.

3.14 DISASSEMBLY AND INSPECTION OF REMOVABLE PARTS

Inspection of removable parts should be made whenevermaintenance is performed or pump requires disassembly.

WARNING

Hazardous Moving PartsRevolving pump head can grab, mangle, and causeserious crushing injury. The Power switch must beplaced in the OFF position for cleaning and powermust be disconnected when disassembling orservicing.

CAUTION

System Under PressureNever disconnect hoses from freezer or pump withoutfirst opening spigot to relieve pressure.Figure 22. Mix Pumps

MixDischarge

3-way Tee

HoseHolder

MixIntake

Page 29: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

19

NOTEIf the mix lines or air line is difficult to remove, softenwith a rag soaked in hot water. Hose connectionsmay be sprayed with Haynes Sanitary Lubricant forease of removal. Do not loosen or remove the mixpump cover wingnuts. Maintain the mix pump hosein its operational condition.

1. Loosen clamp and remove air hose from pumpcompressor.

2. Loosen clamp and disconnect mix pump hose.Remove the pickup hose, mix check valve and pickuphose adapter (and bag adapter if applicable) as anassembly from mix container.

3. Completely disassemble both hose assemblies andcheck valve. Place hoses, tee, check valve assem-bly, and pickup hose adapter in 90° to 110°F (32°C to43°C), mild detergent water and wash thoroughly. Usesoft bristle brushes to clean inside of fittings. Rinseall parts in clean 90° to 110°F (32°C to 43°C) water(see Figure 23).

4. Carefully inspect each part for wear or damage.Replace worn or damaged parts.

5. Wash feed tube and air tube with 90° to 110°F deter-gent water and brushes provided. Rinse with clean,90° to 110°F water (See Figure 24 and 25).

6. Prepare two gallons (7.5 liters) of sanitizing solutionusing a USDA certified grade sanitizing solution.Sanitize all removed parts, then air dry.

7. Check Hose Service Record decal to determine ifhose reposition or replacement is required at thistime.

8. Reassemble both hose assemblies per the diagramlocated on the inside of the cab door. Reconnectassemblies to the pump and discharge hose, usingthe clamps. (See Figure 26 or refer to Section 2.5Mix Pump).

Figure 25. Cleaning Feed Tube

Figure 24. Cleaning Air Tube

Figure 23. Removable Parts Figure 26. Mix Pump Tube Routing

9. Sanitize assembled freezer as per instructionsoutlined in Section 3.9).

PumpCompressor

Page 30: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

20

Page 31: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

21

SECTION 4MAINTENANCE INSTRUCTIONS

4.1 FREEZER ADJUSTMENTThis section is intended to provide maintenance person-nel with a general understanding of the freezer adjust-ments. It is recommended that any adjustments in thissection be made by a qualified person.

4.2 PRODUCT TEMPERATURE ADJUSTMENTA potentiometer is used to control the product tempera-ture. To change the temperature of the product, follow thesteps below:

A. Loosen the two screws under the header displaysign, then pull sign out and down.

B. Use a screw driver to make desired adjustment. Alabel near the potentiometer will give complete in-structions (see Figure 26).

Figure 27. Potentiometer

4.3 OVERRUN ADJUSTMENTThe product when served is a combination of air and mix.Overrun is a measure of the amount of air blended into themix.

Overrun can be expressed in terms of the amount ofweight loss for a given volume. For example, if a pint ofliquid mix weighs 18 ounces (510 grams) and a pint offrozen product with air added weighs 12 ounces (340grams), the overrun is said to be 50 percent "18 oz. (510grams) - 12 oz. (340 grams) = 6 oz. (170 grams)", (6 /12)x 100 = 50%.

The overrun can be checked by placing a one pintcontainer on an ice cream scale and zeroing out the scale.Then fill a one pint container with frozen product. Thecontainer should be filled over the top and leveled with astraightedge. The product should not contain any airpockets. When weighed on an ice cream scale, one pint(473 milliliters) of product should weigh 12 to 13 ounces(340 to 368,5 grams) for an overrun of 45 to 50%.

The mix pump that fills the left freezing cylinder of the U444has been preset at the factory to produce a soft serveproduct with approximately 40% overrun. The mix pumpthat fills the right freezing cylinder of the U444 has beenpreset at the factory to produce a shake product withapproximately 50% overrun. The left and right pumps onthe U421 have been preset to produce a soft serve productwith approximately 40% overrun. Because of differencesin mix formulation, temperatures and barometric pressure,this figure may vary. It will be necessary for approximately2 gallons (7,5 liters) of mix to be pumped thru the freezerbefore changes in the product are noticeable due toadjustments in overrun.

Overrun is controlled by the length of the air compressorpiston stroke within the piston cylinder. Lengthening thestroke within the cylinder will increase overrun. Con-versely, shortening the stroke will decrease overrun. Toperform an overrun adjustment, refer to the followingprocedure:

A. Turn the mix pump switch to the OFF position .

B. Remove the lower back panel from freezer.

C. On air compressor side of pump, locate the long/slender piston rocking arm. The rocking arm down-ward travel is limited by a stationery cam. On the faceof the cam there is an overrun setting indicator platenumbered 3 thru 8 and an adjustment knob (seeFigure 27).

D. The overrun setting is indicated by a pointed pin.

E. To adjust overrun, loosen the allenhead screw(located within the center of the adjustment knob)with the 5/32" (4mm) allen wrench provided. Rotatethe adjustment knob counterclockwise to a highernumber for higher overrun, or clockwise to a lowernumber for lower overrun. Each number multiplied by10 represents the overrun percentage (ie: #4 = 40%overrun).

Overrun Adjustment

Figure 28. Overrun Adjustment

Page 32: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

22

CAUTIONUTION

Never disconnect hoses from freezer or pump with-out first opening spigot to relieve pressure.

3. Disconnect mix pump hose at each end.

4. Grasp the discharge hose end with one handand turn the pump on. Pull down on the hoseuntil all of the remaining hose is removed fromthe pump.

5. Connect new mix pump hose to pick-up hoseadapter, using small clamp.

6. Insert free end of hose into the pick-up (suctionside) hose side of the black cover. Gently pushthe hose into the black cover until it begins toself-feed. Allow the hose to feed itself throughthe pump until the pick-up hose adapter pre-vents further feeding, then turn the pump off.

7. Reconnect mix pump hose to T using smallclamp. Pump is now ready to sanitize.

4.6 CAB TEMPERATURE ADJUSTMENTA temperature control is used to control cab temperature.To change the temperature, follow the steps below:

A. Remove the six screws holding the left side paneland remove panel.

B. Use a small screwdriver to adjust the temperaturecontrol. Turn counterclockwise for a warmer tem-perature and clockwise for a colder temperature. Itwill take about an hour for the cab temperature tochange. Figure 28.

C. Install side panel and secure with the six retainingscrews.

Figure 29. Temperature Control Cab

4.7 DRIVE BELT TENSION ADJUSTMENTTo check belt tension, refer to Figure 29 and follow thesteps below:

F. Tighten the allen screw, then place the wrench backin its clip. Replace the lower back panel and securewith the four screws. Turn the mix pump power switchto the ON position.

4.4. MIX PUMP HOSE REPOSITION (every one ortwo weeks.)

NOTICEMix pump hose must be repositioned every 1 - 2weeks. Failure to comply will result in reduced mixpump liquid capacity, dispense stoppage, popping,and possible mix pump hose leakage.

1. Run cleaning solution through pump.

2. Turn pump off and relieve any pressure byopening the spigot.

3. Grasp the pick-up hose end of the mix pumphose with one hand and turn the pump on. Pulldown on the pick-up hose end until 12 to 14"(30-1/2 to 35-1/2cm) of tubing has reverse fedthrough the pump, then turn the pump off.

4. Loosen small clamp at the pick-up hoseadapter and (Viewed from Back) disconnectmix pump hose.

5. Cut 7-1/2" (19 cm) off the end of the mix pumphose.

6. Reconnect mix pump hose to adapter.

7. Continue normal operation. Mix hose willautomatically reposition itself with adapter nearblack cover.

NOTICEEach hose is long enough for 3 repositions beforereplacement is required. Record each event onHose Service Record decal.

4.5 MIX PUMP HOSE REPLACEMENT

NOTICEMix pump hose must be replaced when tubing can-not be further repositioned (every four to eightweeks). Failure to comply will result in hose failureand possible pump damage.

1. Run cleaning solution through pump.

2. Turn pump off and relieve any pressure byopening the spigot.

WARNING

The Mix pump switch must be in the "Off" positionwhen servicing or cleaning pumps.

WARNING

Disconnect electrical supply to freezer before ser-vicing.

Page 33: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

23

A. Remove either side and back panels.

B. Press firmly on one belt. Figure 29.

Figure 30. Belt Adjustment

C. When the tension is properly adjusted, the outsideof the depressed belt should be approximately inline with the inside of the other belt.

D. If an adjustment is necessary, loosen the four motorplate retaining nuts, adjust belt tension then retighten the four nuts.

NOTICEBelt life will be increased if new drive belts are tight-ened after two or three weeks of operation.

4.8 CONDENSER CLEANING (AIR-COOLED FREEZERS)The condenser requires periodic cleaning. To clean thecondenser, refer to the following steps:

NOTICESome freezers have a condenser filter, to clean re-move and wash in warm soapy water. Rinse in cleanwater and shake dry, taking care not to damagefilter in any way.

A. Visually inspect the condenser for dirt.

B. If the condenser is dirty, place a wet towel over thecondenser.

C. Using compressed air or CO2 tank, blow out the dirtfrom the back of the condenser. Most of the dirt willcling to the wet towel.

CAUTION

This procedure emits a loud noice. Wear hear protec-tion to prevent hearing loss.

D. An alternative method is to clean with a con-denser brush and vacuum.

NOTICEIf the condenser is not kept clean, loss of refrig-eration efficiency will result.

4.9 PREVENTATIVE MAINTENANCEIt is recommended that a preventative maintenance sched-ule be followed to keep the freezer clean and operatingproperly. The following steps are suggested as a preven-tative maintenance guide.

WARNING

Never attempt to repair or perform any maintenanceon freezer until all main electrical power has beendisconnected.

The United States Department of Agriculture and the Foodand Drug Administration require that lubricants used infood zones be certified for this use. Use lubricants only inaccordance with the manufacturer's instructions.

A. Daily Checks

Check for any unusual noise or condition and repairimmediately.

B. Month Checks

1. Check drive belts for wear and tighten belts ifnecessary. (Refer to Section 4.7.)

2. Check the condenser for dirt. (Refer to Section4.8).

WARNING

Never attempt to repair or perform any maintenanceon freezer until all main electrical power has beendisconnected.

4.10 EXTENDED STORAGERefer to the following steps for winterizing the freezer or forstoring the freezer over any long period of shutdown time.

A. Clean thoroughly with warm detergent all parts thatcome in contact with mix. Rinse in clear water anddry all parts. Do not sanitize.

NOTICEDo not let cleaning solution stand in freezer barrelor mix pump during the shutdown period.

B. Remove, disassemble, and clean the front door,auger shaft, and mix pump. Leave disassembledduring the shutdown period.

C. Place plastic auger flights in a plastic bag with amoist paper towel. This will prevent flights frombecoming brittle if exposed to dry air over anextended period of time (over 30 days).

Page 34: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

24

D. For water-cooled freezers that are left in unheatedbuildings, or buildings subject to freezing, the watermust be shut off and disconnected. Disconnectfittings at water valve inlet and water outlet lines atthe freezer. The fittings are located at the rear of thefreezer. Run the compressor for 2 - 3 minutes toopen water valve. Blow out all water, first throughwater inlet, then through water outlet lines with air orcarbon dioxide. Also drain water supply line to thefreezer.

E. Place the mix pump ON-OFF switch, and theCLEAN-OFF-SERVE switch in the OFF position.

F. Disconnect from the source of electrical supply inthe building.

4.11 TROUBLESHOOTINGThe Troubleshooting Table lists the common problemsthat can occur to the freezer.

Page 35: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

25

FREEZER

MELBORP ESUACELBISSOPREZEERF YDEMER

)regua(rotomevirDseodro,"tuo-skcik"

.nurton

.ffosirezeerfotrewoP.1.dedaolrevorotomevirD.2

.egatlovenilwoL.3

.drahoottcudorP.4

.ylerucesdellatsnitonroodtnorF.5

.rezeerfotrewopkcehC.1daolrevoomrehTrof.nim02-51tiaW.2

.teserotfo%01-\+ebtsum,kcehC.3

.egatlovetalpemantcudorpro/dnanurrevoesiaR.4

)2.4ro3.4noitceSeeS(.erutarepmet.ylerucesroodtnorfllatsnI.5

tonseodrosserpmoC.etarepo

.ffofirezeerfotrewoP.1.dedaolrevorotomevirD.2

.egatlovenilwoL.3

sidaolrevolanretnirosserpmoC.4.tuo-tuc

.ylerucesdellatsnitonroodtnorF.5

.rezeerfotrewopkcehC.1otdaolrevoomrehTrof.nim02-51tiaW.2

.teseretalpemanfo%01-/+ebtsum,kcehC.3

.egatlov.tceSeeS()deloocria(resnednockcehC.4

.)deloocretaw(yppusretawro,)8.4.ylerucesroodtnorfllatsnI.5

.tfosoottcudorP .hgihootsignitteserutarepmeT.1.nwodkaerbtcudorP.2

ybdnatSnihctiwSevreS/ybdnatS.3.noitisop

)2.4noitceSeeS(.erutarepmettsujdA.1.tcudorphserfhtiwlliF.2

evreSnihctiwSevreS/ybdnatSecalP.3.noitisop

tcudorP(.pu-ezeerFesnepsidtonlliw

).ylisae

.wolootsignitteserutarepmeT.1.gnittesnurrevowoL.2.erusserppmupwoL.3

.lerrabnitekcopriaegraL.4.esiwkcolc-retnuocgninrutreguA.5

)2.4noitceSeeS(.erutarepmettsujdA.1)3.4noitceSeeS(.nurrevoesiaR.2

.erusserppmupkcehC.3.lerrabmorfriaegruP.4

.esiwkcolcotnoitatoregnahC.5

.skaellaesreguaraeR .detacirbultonlaesreguaraeR.1.gnorwdellatsnirognissimlaeS.2

.tfahsdehctarcsronroW.3

)8.3noitceSeeS(.laesetacirbuL.1)8.3noitceSeeS(.kcehC.2

.tfahsecalpeR.3

.skaeltogipS .detacirbultonerastraptogipS.1.sgnir-onrowrodeppihC.2

.gnorwdellatsnitogipsnosgnir-O.3roodtnorfnodehctarcsroskciN.4

.detacolsitogipserehw

)8.3noitceSeeS(.etacirbuL.1.sgnir-OecalpeR.2

.sgnir-OkcehcdnatogipsevomeR.3.roodtnorfecalpeR.4

rognippilsstlebevirD.gnilaeuqs

.tcerroctonnoisnettlebevirD.1.)s(tlebnroW.2

.wolootsignitteserutarepmeT.3.nurrevowoL.4

)7.4noitceSeeS(.noisnettlebtsujdA.1.stlebecalpeR.2

)2.4noitceSeeS(.erutarepmettsujdA.3.kaelriarofkcehC.4

ooterutarepmetxiM.bacnimraw

.tnaregirfernowolmetsyS.1ootteslortnocerutarepmeT.2

.mraw

)ecivreS.girfeR(.tnaregirferddA.1etacoldnalenapedistfelevomeR.2

wollofdnalortnocerutarepmet.lacednosnoitcurtsni

ooterutarepmetxiM.bacnidloc

.dlocootteslortnocerutarepmeT.1 etacoldnalenapedistfelevomeR.1wollofdnalortnocerutarepmet

.lacednosnoitcurtsni

Page 36: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

26

MIX PUMP

NURTONSEODROTOMPMUP.1

.ffosipmupotrewoP .pmupotrewopylppuS

.egatlovwoL .egatlovenilwolrofkcehC

.pmalc/revockcalbedisnidemmajesohpmupxiM ruofevomeR.ecruosrewopmorfpmuptcennocsiDpmalc/revocetarapeS.swercsbmuhtpmalc/revoc

.esohdemmajevomeR.flahretuoevomerdnasevlahswercsbmuhtruofnethgitdnapmalc/revocllatsni-eReeS.teserotdaolrevolamrehtrotomwollA.ylerucesdemmajesutonoD.tnemecalperesohrof5.2.ceS

.esohfonoitrop

.dedaolrevorotompmuP enimreted;teserotdaolrevolamrehtlanretniwollA.riaperdnaesuacdaolrevo

.evitcefedsipmupnohctiwserusserP .rotubirtsiDgnitleotSlacolruoytcatnoC

roticapac/rotomevitcefeD .rotubirtsiDgnitleotSlacolruoytcatnoC

.hctiwselggotevitcefeD .rotubirtsiDgnitleotSlacolruoytcatnoC

LLIFTONLLIWREDNILYCTUBSETAREPOPMUP.2

.SDNOCES9TUOBANIXIMHTIWPUC.ZO8NALLIFLLIWPMUPGNIKROWYLREPORPA:1ETON

S'TIHSILBATSE-EROTELBANUEBYAMPMUPEHT"EGNAHCGAB"ARETFAYLETAIDEMMI:2ETON3-2WARD.FFOPMUPEHTNRUT,ESACSIHTNI.ERUSSERPGNITAREPOTAMETSYSEHTHTIWEMIRPGABXIMNIRIAGNINIAMEREGRUP.NOPMUPNRUT.OREZOTERUSSERPMETSYSECUDEROTSTNIP

.ESOHPU-KCIPDNA

tnetxeehtotriafogabximehtegrup,gabximehtotesohpu-kcipehtgnitcennocerofeB:TNATROPMI.elbissop

.xiMfotuO .ylppusximhsinelpeR

.pmalc/revockcalbedisnideknikesohpmupxIM ).evoba1#eeS(.riaperdemmajesohpmupximwolloF

.yltcerrocnidelbmessasesoH .snoitcennocesohtcerrocrofmargaidotrefeR

.dedeecxesiefilecivresesohpmupxiM .5.2.ceSeeS.esohpmupximecalper/noitisopeR

.rezeerfotdetcennoctonesohpmupxiM .rezeerfotesohpmupximtcennoC

.ximnislatsyrcecI .esuotroirpximwahtyletelpmoC

.retpadatsniaganwardgabxiM .ebutpu-kcipforaelcsigaberussA

.ximnistcejbongieroF .ximhserfesU.egakcolbraelC

.sdrawkcabdellatsnisievlaVkcehCxiM .noitatneiroreporprofworrawolfevresbO

NURREVOONROWOLOOTNURREVO.3

.wolootgnittesnurrevO .gnittesnurrevoesaercnI

.kaelriA .spmalcesohllanethgiT

.riagnipmuptonrosserpmocriA .rotubirtsiDgnitleotSlacoltcatnoC

HGIHOOTNURREVO.4

.dedeecxesiefilecivresesohpmupxiM .esohpmupximecalper/noitisopeR

.ximfotuO .ylppusximhsinelpeR

.hgihootgnittesnurrevO .gnittesnurrevoesaerceD

.gnispallocsiesohpmupximfogelpu-kciP .5.2noitceSeeS

.EVOBA"2"EESOSLA:ETON

Page 37: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

27

PMUPHGUORHTDEEFT'NOWESOHPMUPXIMTNEMECALPER.5

.revocpmupximfoelohegrahcsidotniesohgnideeF .revocfoedispu-kcipotniesohdeeF

.ylerauqstuctonsdneesoH .)sliaton(ylerauqsffodneesohtucylluferaC

.ylkciuqootgnideefecroF pu-kcipotnipuesohfognideeftsissaylwolsdnayltneG.revocfoedisesoh

.gninnurtonrotompmuP .evoba1metIeesoslA.hctiwsrotomnonruT

ESOHPU-KCIPXIMGNITIXERIA.6

.gnissimevlavkcehcebutpukciP .rotubirtsiDgnitleotSlacoltcatnoC

"SPOP"RIATCUDORPDESNEPSID.7

.hgihootgnittesnurrevO .esohpmupximecalper/noitisopeR

.dedeecxesiefilecivresesohpmupxiM .esohpmupximecalper/noitisopeR

.yticapacs'rezeerfehtgniwardrevO .etaresnepsidecudeR

.noitidnoc"tuo-xim"tneceR .tuo"hcleb"otriassecxewolladnaylluftogipsnepO

.EVOBA4&2EESOSLA:ETON

PMUPMORFEGAKAELXIM.8

naelcdnaelbmessasidyletaidemmi,stisopedximdeirdmorfegamadpmupximtneverpoT:NOITUAC.pmup

.dedeecxesiefilecivresesohpmupxiM rewopmorfpmuptcennocsiD.esohpmupximevomeRYLHGUOROHT.pmalc/revocpmupximevomeR.ecruos

dellifelttobyarpsagnisusrellorezeeuqseerhtesnireeS.pmupmorfximllanaelcylhguorohT.retawtohhtiw

.tnemecalperesohrof5.2.ceS

YTICAPACROOPSAHPMUP.9

.dedeecxeerastimilnurdnatfiL .nur'02,tfil'01otdetimilsipmuP

.7&6,4,2eesoslA:ETON

GNIKAEUQS/YSIONSIPMUP.01

GNIKCILCEVITITEPERASETAERCMRAGNIKCORROSSERPMOCRIAEHTFONOITCAEHT:ETON.LAMRONSISIHT.NOITAREPOGNIRUDDNUOS

SESOHRIANIXIM.11

.pmalc/revockcalbevobaeetxim/riA .pmalc/revockcalbwolebebtsumeetxim/riA

.kaelriA .spmalcesohllanethgiT

.gnittifeetxim/riagnorwnoesohxiM .snoitcennocesohtcerrocrofmargaidotrefeR

Page 38: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

28

Page 39: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

29

SECTION 5HOW TO ORDER REPLACEMENT PARTS

5.1 HOW TO ORDER REPLACEMENT PARTSTo assure the receipt of the proper replacement parts,supply your Authorized Stoelting Distributor with thefollowing information:

A. Model number of equipment.

B. Serial number of model (stamped on nameplate)

C. Part number, part name, and quantity needed.

NOTICE Minimum billing is $50.00 Net.

5.2 PARTS LIST AND REFERENCE DRAWINGSThe following lists and drawings will aid the user whenordering parts or servicing.

Page 40: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

30

DrawingIndex No. Part No. Description

7 625133 O-ring, Front Door11 624520 O-ring, Air Bleed Valve12 694200 Spring, Air Bleed Valve13 482004 Knob, Air Bleed, Black14 2110116 Stem, Air Bleed Valve15 1107123 Spigot Handle16 570998 Retaining Pin17 2146293 Spigot Extension, 2.1

2157892 Spigot Extension, 1.52143024 Spigot Extension, 3.2

18 624655 Spigot O-ring19 624645 Spigot Extension O-ring20 3152581 Spigot, White21 624677 Spigot O-ring22 1177905 Front Door23 482035 Knob, Black

FRONT DOOR PARTS

Page 41: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

31

AUGER PARTS

Drawing PartIndex No. Number Qty. Description

1 2104552 1 Auger Front Support2 149003 1 Front Bearing3 381804 6 Plastic Flight4 694255 6 Spring5 4151178 1 Auger6 624678 1 Rear Seal O-ring7 1151859 1 Rear Seal Adaptor8 667868 1 Rear Seal

MISCELLANEOUS PARTS

Description Part No.

Haynes Spray 12 oz.(340 grams) -------------------- 508017Petro-Gel Tube 4 oz. (113 grams) -------------------- 508135Spline Lubricant 2 oz. (57 grams) -------------------- 508048Brush 4"x 8"x16" (10cm x 20cm x 40,5cm) ------- 208135Brush 2.5"x 4"x12" (6,5cm x 10cm x 30,5cm) ---- 208146Brush .25"x 4"x14" (,6cm x 10cm x 35,5cm) ----- 208380Brush 1"x3.5"x18" (2,5cm x 9cm x 45,5cm) ------ 208465Drip Tray --------------------------------------------------- 744273Drip Tray Grid --------------------------------------------- 417006

Page 42: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

32Figure 7. Mix Pump

264241

376041

756088

694247

762256756088

1151965

696130

1172864

375867

756088

756204

756067

Page 43: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

33

DECALS

Qty. Part Number Description

2 324200 H.P. Manual Reset2 324798 Clean-Off-Serve2 324797 Standby/Serve1 324800 Cab Off-On2 324799 Pump Off On1 324141 Caution, Haz. Rot. Blade - Front Panel1 324509 Cleaning - Right Side2 324014 Auger Rotation - Evap. Enclosure Rear4 324686 Danger - Start Auto, on Evap. Support between belts & motors support brkt.1 723525 Winterizing, Attach to water hose near bottom2 324106 Caution - Elec. Wiring Mat'ls must conform between water couplings, one rear

panel bottom2 324346 Caution - Haz. Mov. Parts, on inside of mtr support brkt @ rear3 324107 Caution - Haz. Mov. Parts, on cond. bkt. rear & (2) on evap. enclosure sides2 324208 Attn - Ref. Lk Chk, on evap. enclosure sides2 723552 Tag - Supply volt., inside J-Box1 723517 Card - Inside one J-Box2 ID Tags, Back Panel Top1 324548 Add. Vent Back Panel Ctr Top1 Made in U.S.A. - Back panel2 324103 Caution - Rot. Shaft, on gearbox support bracket2 324151 Field Connections, J-Box cover, outside3 324125 Danger Elec.Shock, J-Box covers outside, back panel bottom1 324242 Warm/Cold, @ T-Stat2 324565 Night/Serve - Temp. Control Bracket2 324158 Use copper cond. only, inside both J-boxes2 324566 Wired According to, on elec. schematic envelope2 130000 Elec. Schematic Envelope1 324065 Water Inlet - Back panel above inlet coupling1 324803 Header panel decal (Stoelting Logo)1 324804 Header panel decal (Stoelting Swirl)1 324805 Header panel decal (DQ Logo)

Page 44: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

34

Page 45: Model U421/U444 OWNER'S MANUALstoelting.us/PDFs/FloorPressureFed/U421G Owner's Manual.pdf29 324242 Decal Temperature Control 30 324200 Decal Manual Reset 32 324014 Decal Arrow 33 324496

WARRANTYSOFT SERVE / SHAKE FREEZERS

1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors,

speed reducers, augers and auger flights of Stoelting soft serve / shake freezers will be free from defects in materialsand workmanship under normal use and proper maintenance appearing within five (5) years, and that all othercomponents of such equipment manufactured by Stoelting will be free from defects in material and workmanshipunder normal use and proper maintenance appearing within twelve (12) months after the date that such equipment isoriginally installed.

2. Disclaimer of Other Warranties:

THIS WARRANTY IS EXCLUSIVE; AND STOELTING HEREBY DISCLAIMS ANY IMPLIED WAR-RANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE.

3. Remedies:Stoelting’s sole obligations, and Buyer’s sole remedies, for any breach of this warranty shall be the repair or (atStoelting’s option) replacement of the affected component at Stoelting’s plant in Kiel, Wisconsin, or (again, atStoelting’s option) refund of the purchase price of the affected equipment, and, during the first twelve (12) months ofthe warranty period, deinstallation/reinstallation of the affected component from/into the equipment. Those obliga-tions/remedies are subject to the conditions that Buyer (a) signs and returns to Stoelting, upon installation, theChecklist/Warranty Registration Card for the affected equipment, (b) gives Stoelting prompt written notice of anyclaimed breach of warranty within the applicable warranty period, and (c) delivers the affected equipment to Stoeltingor its designated service location, in its original packaging/crating, also within that period. Buyer shall bear the costand risk of shipping to and from Stoelting’s plant or designated service location.

4. Exclusions and Limitations:This warranty does not extend to parts, sometimes called “wear parts”, which are generally expected to deteriorateand to require replacement as equipment is used, including as examples but not intended to be limited to o-rings,auger seals, auger support bushings and drive belts. All such parts are sold

AS IS.

Further, Stoelting shall not be responsible to provide any remedy under this warranty with respect to any componentthat fails by reason of negligence, abnormal use, misuse or abuse, use with parts or equipment not manufactured orsupplied by Stoelting, or damage in transit.

THE REMEDIES SET FORTH IN THIS WARRANTY SHALL BE THE SOLE LIABILITY STOELTINGAND THE EXCLUSIVE REMEDY OF BUYER WITH RESPECT TO EQUIPMENT SUPPLIED BYSTOELTING; AND IN NO EVENT SHALL STOELTING BE LIABLE FOR ANY INCIDENTAL ORCONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF WARRANTY OR OTHER CONTRACTBREACH, NEGLIGENCE OR OTHER TORT, OR ON ANY STRICT LIABILITY THEORY.