model jc1000 laboratory jaw crusher - jointlab.com a ganasce.pdf · adjusting range of jaw outlet 2...

LabtechEssa

Labtech Essa Pty Ltd8 Yelland Way, BassendeanWestern Australia 6054, AustraliaPhone:+61 (08) 93773677Fax: +61 (08) 93773420email: [email protected] April 2002

Jaw Inlet (mm) 130 x 100Maximum feed size 85% of jaw inlet*Adjusting range of jaw outlet 2 to 25 mmProduct sizing at min adjustment * 4mm nominalApproximate capacity * 250 kg/hrMotor power 2.2 kW, 3 phaseOperating speed 600 rpmApprox. Dimensions (mm) 460 W x 1100x 1150HHeight, floor level to feed hopper 1055 mmHeight (floor to top of product drawer) 600 mmApproximate mass (crated) 250 kgDust extraction points fitted 1 off

Model JC1000Laboratory Jaw Crusher

A medium duty general purpose 130 X 100 mmlaboratory jaw crusher

The Labtech Essa model JC1000 is awell proven single toggle jaw crusherthat finds general application in avariety of laboratory environments. Itreadily accepts soft to medium hardore, rock and similar particulate up to85% of its 130 x 100 mm jaw opening.

STANDARD FEATURES:• Fabricated steel construction• Roller bearings used throughout• Fabricated steel support frame for floor mounting• Feed hopper (with hinged lid and dust extraction

connection) and product drawer• Electric pre-wiring with an IP55 enclosed stop/start

and motor protection station.• Full drive guarding• Vertically serrated jaw plates. Jaw plates are revers-

ible for extended life• Fast, easy adjustment of product sizing

TECHNICAL DATA

* These are nominal only performance expectations that can vary according to thephysical characteristics of the material being crushed, the condition of the jaws, thecrusher adjustment and the method of feeding the crusher. Labtech Essa are able toconduct tests at their factory to determine how the crusher will perform whenprocessing your material.

LabtechEssa


Model JC5000Heavy Duty Jaw Crusher

A heavy duty, general purpose 500 x 300 mm jaw crusher

The Labtech Essa model JC5000 is a rugged,single toggle, job proven jaw crusher thatfinds general application in a variety ofoperating environments. It readily accepts softto very hard ore, rock and similar particulateup to 85% of its 500 x 300 mm jaw opening.This is a heavy duty machine suitable for usein a continuous or large batch operatingenvironment. Typical applications will includeprimary crushing of large lump ore in sam-pling stations and pilot plants and in the pre-crushing of materials being prepared foranalytical or metallurgical laboratory use.

STANDARD FEATURES:• Rugged, fabricated steel construction• Roller bearings used throughout• Fabricated steel base for mounting on

customers support frame or concretefooting

• Full drive guarding• Vertically serrated chrome steel jaw plates.

Jaw plates are reversible for extended life• Fast, easy adjustment of product sizing

TECHNICAL DATA

Jaw Inlet (mm) 500 x 300Maximum feed size 85% of jaw inlet *Usual product sizing * 25mm nominalMaximum product size * 75mm nominalApproximate capacity * 15000 kg/hrMotor power 22 kW, 3 phaseToggle speed 320 rpmApproximate mass 3500kgDust extraction points fitted No

* These figures should be used as guides only. Crusher settings and thecharacteristics of the material being crushed will cause variations in operatingperformance. Contact Labtech Essa for further information about the expectedperformance of this crusher in your application

Approximate overalldimensions of the JC3000are 1300 mm wide (overflywheels) x 1600 mm x1440 overall height.

Well Proven, High Reduction Primary Jaw Crusher The Essa Australia Model JC3000 is a well proven single toggle, high reduction jaw crusher that finds general application in a variety of operating environments. It readily accepts soft to very hard ore, drill core, rock and similar particulate up to 85% of its jaw opening. This a heavy duty, low maintenance machine suitable for use in a large batch or continuous operating environment. Typical applications will include general primary crushing of lump ore in analytical and metallurgical laboratories, sampling stations and pilot plants

Standard Features Rugged, fabricated steel construction Roller bearings used throughout Electric pre-wiring with an IP55 enclosed stop/start

and motor protection station Feed hopper and sample drawer with dust extraction

points OR

Fabricated steel base for mounting on customer’s support frame or concrete footing

Full drive guarding Vertically serrated chrome steel jaw plates Jaw plates are reversible for extended life

Datash

eet Sam

ple

Pre

para

tion

Jaw C

rush

er Model JC

3000

Jaw Crusher Model JC3000

A Heavy Duty, General Purpose 300mm x 200mm Jaw Crusher

1/2

Technical Data Jaw Inlet 300mm x 200mm

Maximum Feed Size 170mm i.e. 85% of jaw inlet

Usual Product Sizing Nominally 25mm (but ranges from 10mm to 40mm)

Maximum Product Size Nominally 50mm

Throughput 3,000kg to 8,000kg per hour

Dust Extraction Points Two (2)

Dust Extraction Flow

Electrical Requirements (3 phase) 7.5kW

Toggle Speed 350rpm

Approximate Mass 1,165kg

270 litres per second (180L/sec upper point and 90L/sec lower point)

Please note that the figures quoted above are nominal only performance expectations that can vary according to the physical characteristics of the material being prepared, the condition of the equipment, the gap adjustment and the method of feeding the crusher. Essa Australia are able to conduct tests at their workshop to determine how the sample preparation equipment will perform when processing your material.

www.essa.com.au Essa Australia Limited, PO Box 362, Belmont, WA 6984 AUSTRALIA

phone +61 9475 3000 fax +61 8 9477 3544 email [email protected]

Datash

eet Sam

ple

Pre

para

tion

Jaw C

rush

er Model JC

3000

2/2

Typical JC3000 configuration for stand alone analytical or metallurgical laboratory use Approximate overall dimensions are 800mm wide x 1020mm deep x 1550mm high

Typical JC3000 configuration for continuous use such as in mechanical sampling stations or pilot plants

March 2008

LabtechEssa


Model JC2000Heavy Duty Jaw Crusher

A heavy duty, general purpose200 x 130 mm jaw crusher

The Labtech Essa model JC2000 is a well proven singletoggle jaw crusher that finds general application in a varietyof laboratory environments. It readily accepts soft to hardore, rock and similar particulate up to 85% of its 200 x 130mm jaw opening. This is a heavy duty machine suitable foruse in a batch or continuous operating environment. Typicalapplications will include general primary crushing in analyti-cal and metallurgical laboratories, sampling stations andpilot plants.

STANDARD FEATURES:• Fabricated steel construction• Roller bearings used throughout• Fabricated steel support frame for floor mounting• Feed hopper and product drawer (each with dust extrac-

tion point)• Electric pre-wiring with an IP55 enclosed stop/start and

motor protection station.• Full drive guarding• Vertically serrated chrome steel jaw plates. Jaw plates are

reversible for extended life• Fast, easy adjustment of product sizing

Standard configuration, complete with infeedhood and product drawer.

Optional configuration for mounting in ahorizontal position.

Dimensions are approximate only.

TECHNICAL DATA

** Recommended extraction flow is 80 l/sec (upper) and 90 l/sec(lower)

* These figures should be used as guides only. Crusher settings and thecharacteristics of the material being crushed will cause variations inoperating performance. Contact Labtech Essa for further informationabout the expected performance of this crusher in your application.

Jaw Inlet (mm) 200 x 130Maximum feed size 85% of jaw inlet *Usual product sizing * 6mm nominalMaximum product size * 35mm nominalApproximate capacity * 500 kg/hrMotor power 4 kW, 3 phaseToggle speed 300 rpmApproximate mass 550kgDust extraction points fitted ** 2 off **

600 670

1440

model jc1000 laboratory jaw crusher - jointlab.com a ganasce.pdf · adjusting range of jaw outlet 2...

Documents