model 83a-bs & 83a-bsh
TRANSCRIPT
83ABSBSH
Bulletin No. MCE-B 4307E
General Specifications
SEAL-RING BALANCE TYPE ・CAGE GUIDED CONTROL VALVEModel 83A-BS & 83A-BSH
Model 83A-BS and 83A-BSH Cage Guid-ed Control Valve realized very limited seatleakage l ike single seat valves withinstalling small actuator like double seatvalves.
This design adopted Seal-Ring Balance onCage for Type BS and same design onValve Plug for Type BSH.
Seal-Ring inserted in Cage for Type BSand inserted in Valve Plug for Type BSH,seals the guide clearance tightly betweenValve Plug and Cage to prevent the valveinlet pressure comes into the Bonnet.
This design makes the outlet pressurecomes into the upper and lower side of thePlug and it makes the pressure well bal-anced. Consequently, small actuator isrequired to operate the valve.
Seal-Ring structure
FLOW
Valve Plug Holder
Cage
BS
1. VALVE TYPEValve Style and Cage Type
Seal-Ring structure
FLOW
Valve Plug
Guide
BSH
1
【Notes】(1) portion is described in this catalog.(2)See Catalog MCE-B4306 for Cage Guide Type Control Valves
and MCE-B4304 for -NRV, Multi-Hole & Multi-Stage Type Control Valves.(3)See Catalog MCE-B4308 for Model 83A-BS ANSI class 900 & 1500.
83A Cage Type - Plug Type
CV V-Port(V)CS Multi-HoleCS-L Double Stage Multi-Hole Throttling
CQ Quick Opening(Q)
83ACP-S Contoured Plug, Single Seat(Quick opening, Single Seat)
83ACP-S-RT Multi-Stage Plug with Cage Guide
83-NRV Low Noise Multi-Hole & Multi Stage
-BS Seal-Ring Balance(Low & Medium Temp.)-BSH Seal-Ring Balance(High Temp.)-BP Pilot Balance
-S Single Seat(Un-Balanced)
Model 83A-BS & 83A-BSH
83A BSBSH
2. FEATURES
Model CS-BSH helps to attenuate aero-dynamic noise in gas service, with Multi-hole in outer cage.
In l iquid service which may occurcavitation, CS helps to prevent trim fromcavitation damage.
■ Typical Application◯ Low noise valve◯ Anti-cavitation valve◯ Anti-erosion valve
Model CS-L is double stage, multi-holethrottling type control valve providingfixed orifice at the bottom of cage of theModel CS.
Because of double throttling mechanism,these valves permit large noise reductioneffect.
■Typical Application◯ For medium and high pressure gas◯ Steam control valve◯ Low noise valve
Model CV V Port Type
83A -BS 83A -BSH
Model CS Multi-hole Type
Model CS-L Double Stage Multi-hole Throttling Type
Model CV is cage guided control valveand is used for most general purposewith V port of cage characterized,proving wide applicability, excellentcharacteristics at high load, and easymaintenance.
■Typical Application◯ General services◯ Chemical◯ For medium or high pressure
Type CQ for quick opening is also available.
2
Model 83A-BS & 83A-BSH
83ABSBSH
3. SPECIFICATIONS
Valve Type
Valve Model No.
Body Type
Body Size(mm)
Body Size(In.)
Pressure Rating
End Connections
Body Materials
Bonnet Types
Gland Type
Packing(Non Asbestos)
Gaskets(Non Asbestos)
Guiding
Valve Plug Action
Seat Type
Cage Type
Cage Port Characteristics
Flow Direction
Trim Materials
Treatment of Trim
Seal-ring Material
Back-up ring Material
Tension-ring Material
Actuator Type
Actuator Sizes
Max. Stroke(mm)
Supply Air Press.kPaG(kgf/cm2G)
Spring RangekPaG(kgf/cm2G)
Action
Materials
Air Connection
Ambient Temperature
Diaphragm Operated Cage Guided Control Valve
3883A, 2883A
50~350
2~14
JIS10K, 20K,30K,40K ASME/JPI Class 150, 300, 600
Flanged end:FF, RF, RJ, Male and female, Tongue and Groove(※Welding end:SW, BW)
SCPH2, SCPH11, SCPH21, SOPH32, SCPH61, SCS13A, SCS14A, SCS16AWCB, WC1, WC6, WC9, C5, DF8, CF8M, CF3M
■-196℃≦T< -45℃ :Extension Bonnet, Type-H
■ -45℃≦T< -17℃ :Extension Bonnet, Type-F
■ -17℃≦T≦+230℃ :Plain Bonnet
■+230℃<T :Extension Bonnet, Type-F
Bellows Sealed(See Page 6)
Bolted gland
Braided packing, Molded packing
Serrated gasket, Spiral wound gasket
Cage guide
Push-down close
Single seated
Seal Ring Balance Type for Low & Medium Temperature Seal Ring Balance Type for High Temperature
FTC(Flow to close)
SUS316(SCS14A), SUS440B, SUS630(SCS24)See Page 5~6[5.Main Materials]
See Page 5~6[5.Main Materials]
PTFE with Carbon Graphite (Spring: Inconel X750) Metal-reinforced carbon
SUS316
PTFE with Carbon Graphite (for Body Size 200A & Larger) ――――――――
――――――――
Model 3800 Multi-spring type single diaphragm Actuator
240(2.4), 280(2.8), 300(3.0)400(4.0)… N33S・N40 only
40~200(0.4~2.0)80~200(0.8~2.0)
120~280(1.2~2.8)… N33S, N40 only
20~180(0.2~1.8), 40~200(0.4~2.0)60~220(0.6~2.2), 80~240(0.8~2.4)80~200(0.8~2.0)… BSH only
100~220(1.0~2.2)
240(2.4), 280(2.8)300(3.0)… BSH only
Model 2800 Spring type single diaphragm Actuator
N28
38
N33S
38
N40
65
500S
65
500L
100
650S
65
650XS 650L 650XL
130
Direct action, Reverse action
(Diaphragm)Cloth reinforced chloroprene rubber,(Yoke)FC200
Rc 1/4, Rc 3/8(650, 650X only)
Silver,(No painting on stainless steel)
-20℃~+70℃(※-50~-20℃, +70℃~+100℃)
Equal
Percentage
Linear
Linear
Modified Parabolic
ON-OFF
Quick
Opening
Equal
Percentage
Linear
Linear
Modified Parabolic
ON-OFF
Quick
Opening
Painting Color
83ACV-BS 83ACS-BS 83ACS-L-BS 83ACQ-BS 83ACV-BSH 83ACS-BSH 83ACS-L-BSH 83ACQ-BSH
AC
TU
AT
OR
VA
LV
EB
OD
Y
3
Note(3)
Note(7)
Note(2)
-30℃~+70℃(※-50~-30℃, +70℃~+100℃)Note(2)
Note(7)
Note(7)
Model 83A-BS & 83A-BSH
83A BSBSH
【Notes】(1)Valve performance specified above is the condition assembled with standard gland packing(P4519+V7010).(2)It is applicable as Option.(3)Please install the valve in correct direction. Wrong installation will increase seat leakage and shorten Seal Ring life
cycle. This valve is not applicable to a system reverse pressure is expected.(4)Various Option is available on request.(5)ANSI/FCI class V seat leakage ratio is available as option.
Seal Ring design for seat leakage class V is deferent from class IV.(6)Please select single seat valve or pilot balance type valve when severe seat leakage ratio less than 0.01% is required
on type 83-BSH.(7)Application service is limited as follows because of Seal Ring material property for Type BS and BSH control valves.
(Type BS)It is not acceptable to use Type BS for following application.●Food processing service ●Oxygen service ●Any process, coloring by resin is undesirable.●Acids at high temperature and pressure(Aqua Regina, Nitric Acid, Sulfuric Acid, Hydrochloric Acid, etc.)●Fluorine gas(F2), CIF3, OF2 etc. at high temperature.●Metal-hydrogen compound such as 80% KOH, B2H6 etc.
(Type BSH)It is recommended to use Type BS & BSH control valves within the following range because of Seal Ring material properties to prevent oxidation.① For Air service :0 ~+400℃② For steam and Non-oxide service :0 ~+500℃
(8)It is applicable to use type 83-BS valves for some services listed on(7)above, by changing the Seal Ring materials. Please contact our sales office for special application.
(9)It is not recommended to install type 83-BS and 83-BSH horizontally.It will decline the sealing performance.
(10)Type 83-BS seal ring design is not recommended for the services required frequent operation or exposed rapid temperature change to protect the life cycle or sealing performance of the seal ring.
It is recommended to change Seal Ring on every overhaul services like Gland Packing or Gaskets. Kindly keep some Seal Rings for your stock.
Body Type
Control Mode
Valve Action
Applicable Max. Pressure
Applicable Temp.
Allowable DifferentialPressure
Rated Cv Value
Flow CharacteristicsInherent Rangeability
Allowable
Seat Leakage
Ratio
Function
Accuracy
Valve Body
Actuator
Accessories
Others
Hysteresis Error(With Positioner)Linearity(With Positioner)
83ACV-BS 83ACS-BS 83ACS-L-BS 83ACQ-BS 83ACV-BSH 83ACS-BSH 83ACS-L-BSH 83ACQ-BSH
VA
LV
EC
HA
RA
CT
ER
IST
ICS
AN
DP
ER
FO
RM
AN
CE
OP
TIO
NS
Throttling control, On-Off control
Direct action(Air-to close), Reverse action(Air-to open)
9.80 MPaG(100kgf/cm2G)or less(limited by P-T rating)
-50℃~+230℃(See Page 5[4.Applicable Press. & Temp.])
See Page 8[Allowable Differential Pressure]
See Page 7[Rated Cv Valve]
See Page 7[Flow Characteristics]
50:1 See Page 7[Rated Cv Valve]
0.01%of rated Cv(ANSI/FCI ClassⅣ)
Tight Shut Off(TSO),Body Size 100A & Smaller … 0.001 %Body Size 125A & Smaller … 0.002 %
ANSI/FCI ClassⅤ
Max. 2 % F.S.
Max. ±2 % F.S.
Drain plug, Special treatment for trim
Handwheel(Top-mounted, Side-mounted), Travel stop, Diaphragm material;Ethylene propylene rubber, Yoke material:SCPH 2Pneumatic positioner(PA92A), Electro-pneumatic positioner(EA90A, EA91A, EA10S), Air filteregulator(MR2000), Limit switch, Solenoide valve, Booster relay, Speed controller, Lock up valve, Pneumatic operated valve
The hige pressure gas safety low certification, Oil-free, Water-free, Sand-proof, Dustproof, Anti-saltdamage, vacuum service, Cold district spec, Tropical district spec, External exprosure bolt & nut S.S, Optional painting color
ANSI/FCI ClassⅣ(0.01 %at Rated CV)
Max. +550℃(See Page 5[4.Applicable Press. & Temp.])
4
No
te(
1 )
Note(6)
Note(5)
Model 83A-BS & 83A-BSH
83ABSBSH
4. APPLICABLE PRESSURE AND TEMPERATURE
300 400 500230
100 2000-50-100
4.61(47)
5.49(56)
8.92(91)
9.80(100)
0
BSHBS
BS
MPaG(kgf/cm2G)
Fluid Temperature(℃)
Max
. Pre
ssu
re
Available temperature and pressure of Model 83-BS and 83-BSH is shown below.
5
5. MAIN MATERIALS
【Note】 Sheded area needs specialized Seal-Rings.
BS
【Notes】(1)This table shows typical combination of materials. The combination may be subject to change withpressure, temperature and kind of fluid.
(2)Trim materials may be used casting instead of bar materials.
①SUS316(SCS14A), SUS316L(SCS16A)
1 Typical Combination of Materials
2 Hard Facing for Trim
Parts NameSCPH2, 11, 21, 32, 61WCB, WC1, WC6, WC9, C5
SUS316SUS440BSUS630
A193GrB7/S45C(H)
SCS13ACF8
SUS316SUS440BSUS630
SCS14ACF8M
SUS316
SCS16ACF3M
SUS316L
A193GrB8CL2/SUS304
Materials
Body, Bonnet
Trim
Stud Bolt and Nuts
CoCr Alloy Hard Facing
Cage Type
Valve plugHolder:BSGuide :BSH
Cage
Applicable Temp.BS
BSH
CoCr Alloy Seat CoCr Alloy FaceCV-BS, CQ-BSCS-BS, CS-L-BS
CV-BS, CQ-BS, CS-BS, CS-L-BSCV-BSH, CQ-BSH, CS-BSH, CS-L-BSH
CoCr Alloy SeatNo Hard Facing SUS316(SCS14A)/SUS316L(SCS16A)
No Hard Facing ; Design Temp. ≦400℃, CoCr Alloy Face ; Design Temp. >400℃CoCr Alloy Seat-50℃~+230℃
― +500℃or Lower
CoCr Alloy Face
Model 83A-BS & 83A-BSH
83A BSBSH
6
【Notes】(1)SUS440B shall be suitable for flashing or cavitation services within the temp. range of -20℃ to +400℃. It is notapplicable for type CS-L.Hard Facing on SUS316(SCS14A), SUS316L(SCS16A)and SUS630(SCS24)are not recommended for flashingor cavitation services.
(2)SUS630(SCS24)in not applicable for corrosive service as Copper(Cu)contains in the material.(3)When ANSI/FCI seat leakage class V is required, hard facing shall be other materials than SUS630(SCS24).
3 Applicable Pressure and Temperature of Bellows Seal Bonnet(BS, BSH)
②SUS440B, SUS630(SCS24)Note(1)(2)(3)
Materials
Cage Type
Valve plugHolder:BSGuide :BSH
Cage
Applicable Temp.BS
BSH
SUS440B SUS630(SCS24)
CV-BS, CQ-BSCS-BSCV-BSH, CQ-BSHCS-BSH
CS-L-BSCS-L-BSH
CV-BS, CQ-BSCS-BSCV-BSH, CQ-BSHCS-BSH
CS-L-BSCS-L-BSH
SUS440B(Heat treatment)
SUS316(SCS14A)
SUS440B(Heat treatment)
SUS316(SCS14A)+CoCr Alloy SUS630(SCS24)(Heat treatment)
-20℃~+230℃
-20℃~+400℃ or Lower
SUS630(SCS24)(Heat treatment)
0
1.5(15.2)
MPa(kgf/cm2)
-196 -100 0 100 200
230℃
300 400 500 550
Temp(℃)
CoCr Alloy Seat CoCr Alloy Face
Max. Pressure
0
1.0(10.2)
0.5(5.0)
1.5(15.2)
-196 -100 0 150100 200-20℃
300 400
SUS630(SCS24)
SUS440B MPa(kgf/cm2)
Temp(℃)
Max. Pressure
SUS400B, SUS630(SCS24)family Press. / Temp. Range
SUS316(SCS14A), SUS316L(SCS16A)family Press. / Temp. Range
2.94(30)
BA 40K
BA 30K
BA 20K
BA 10K
3.92(40)
1.96(20)
1.76(18)
0.98(10)
0.58( 6)
1.17(12)
0-100 0 100 200 300 350 400 500-196
2.35(24)
Fluid Temperature(℃)
SUS316L SUS347
Max
. Pre
ssu
re
MPaG(kgf/cm2G)
Model 83A-BS & 83A-BSH
83ABSBSH
7
V-port Type Equal percentage(CV-BS, CV-BSH)
100
90
80
70
60
50
40
30
20
10
00.1 0.2 1 2 10 20
3225 40 50 65 80 100 125 150 200 250 300 350
100 200 1000 2000
Port size(mm)
Cv Value
(%)P
erce
nt
of
Rat
ed T
rave
l
3 Flow Characteristics
100
90
80
70
60
50
40
30
20
10
0
Cv(%)
0 10 20 30 40 50 60 70 80 90 100
(%)P
erce
nt
of
Rat
ed T
rave
l
■Modified Parabolic
6. SCOPE OF PRODUCTION
BSH ■Combination of Valve Body and Actuator
BS ■ Combination of Valve Body and Actuator
(1)Allowable Seat Leakage Ratio:0.01% of rated Cv (2)Allowable Seat Leakage Ratio:ANSI/FCI ClassⅤ(Oprion)Valve Model No. 3883A
N28 N33S N40
2883A
500S 500L 650S 650L 650XS 650XLActuator Size
Valve Size50(mm)
6580
100125150200250300350
2(inch)21/234568
101214
●●●●
●●●●
●●●●●●●
●●●●●●●
●●
●●●●●
●●●
●●●●
Valve Model No. 3883A
N28 N33S N40
2883A
500S 500L 650S 650L 650XS 650XLActuator Size
Valve Size50(mm)
6580
100125150200250300350
2(inch)21/234568
101214
●●
●●●●
●●●●●●
●●●●●●●
●
●●●●●
●●●
●●●●
Port Size(mm) 25 32 40 50 65 80 100 125 150 200 250 300 350
15 20 25 38 50 65 90 100 130Rated Travel(mm)
Valve Size50(mm)
6580
100125150200250300350
2(inch)21/234568
101214
◆ ◆◆
◆◆◆
●◆◆◆
●◆◆◆
●◆◆◆
●◆◆◆
●◆◆◆
●◆◆◆
●◆◆◆
●◆◆
●◆ ●
Valve Model No. 3883A
N28 N33S N40
2883A
500S 500L 650S 650L 650XS 650XLActuator Size
Valve Size50(mm)
6580
100125150200250300350
2(inch)21/234568
101214
●●
●●●●
●●●●●●
●●●●●●
●●●●●
●●
●●●
●:Full port ◆:Reduced portBS, BSH ■Scope of Port Size
1 Rated Cv Value
2 The flow characteristic of each type
CV-BS, BSHCS-BS, BSHCS-L-BS, BSHCQ-BS, BSH
○ ○○○
○○
○
Eq. % Linear Mod. parabolic ON-OFF
Body ModelPort size
mm
in.25115
14
11.2
18
14.4
27
22
46
36
71
56
110
88
180
144
275
220
395
316
640
512
1050
840
1460
1168
2000
160050:1
3211/4
20
4011/2
502
25
6521/2
803
38
1004
1255
50
1506
200865
2501090
30012100
35014130Rated Travel(mm)
Rated Cv Value
Inherent Rangeability
CV -BS, BSHCS-BS, BSHCQ-BS, BSHCS-L-BS, BSH
7. FLOW CHARACTERISTICS
【Note】 Shaded zone represents proper throttling control range.
Model 83A-BS & 83A-BSH
83A BSBSH
8
Unit:MPa(kgf/cm2)
■BS
2 Allowable Shut-off Pressure
(1)Allowable Seat Leakage Ratio:0.01%of rated Cv
8. ALLOWABLE DIFFERENTIAL PRESSURE1 Off-balance Classification
Unit:kPaG(kgf/cm2 G)■BS
■BSH Unit:kPaG(kgf/cm2 G)
ActionSpring Range
Supply AirPressure Off-balance PositionerActuator Size
40~200(0.4~2.0) 240(2.4) 40(0.4)
with
with out
with out
with
280(2.8)60(0.6)80(0.8)
100(1.0)300(3.0)
120(1.2)
280(2.8)400(4.0)240(2.4)
280(2.8)
400(4.0)
40(0.4)60(0.6)80(0.8)
100(1.0)120(1.2)
- 60~220(0.6~2.2)40~200(0.4~2.0)
-20~180(0.2~1.8)
-
40~200(0.4~2.0)
-120~280(1.2~2.8)
40~200(0.4~2.0)-
80~200(0.8~2.0)-
120~280(1.2~2.8)
60~220(0.6~2.2)80~240(0.8~2.4)
100~220(1.0~2.2)-
N28~N40 500~650X
DirectAction
ReverseAction
Action
DirectAction
ReverseAction
N28~N4080~200(0.8~2.0)80~200(0.8~2.0)
120~280(1.2~2.8)80~200(0.8~2.0)
-120~280(1.2~2.8)
-80~240(0.8~2.4)
100~220(1.0~2.2)-
500~650X Supply Air Pressure280(2.8)300(3.0)400(4.0)
80(0.8)with
with out
with
with out
100(1.0)120(1.2)80(0.8)
100(1.0)120(1.2)
280(2.8)
400(4.0)
PositionerOff-balance
Body SizeOff-balance
50(mm) 652(in.)
ActuatorSize 2 1/2
803
1004
1255
1506
2008
25010
30012
35014
N28
N33S
N40
500
650
650X
40(0.4)80(0.8)
100(1.0)40(0.4)80(0.8)
100(1.0)120(1.2)
40(0.4)80(0.8)
100(1.0)120(1.2)
40(0.4)60(0.6)80(0.8)
100(1.0)40(0.4)60(0.6)80(0.8)
100(1.0)40(0.4)60(0.6)80(0.8)
100(1.0)
1.96(20)3.92(40)5.00(51)2.94(30)5.88(60)7.35(75)8.82(90)4.11(42)8.23(84)
9.80(100)
6.86(70)
9.80(100)
1.37(14)2.74(28)3.43(35)1.96(20)4.02(41)5.09(52)6.08(62)2.84(29)5.78(59)7.15(73)8.62(88)4.81(49)7.15(73)9.61(98)9.80(100)
1.18(12)2.35(24)2.94(30)1.77(18)3.53(36)4.41(45)5.29(54)2.45(25)4.90(50)6.17(63)7.45(76)4.12(42)6.17(63)8.33(85)9.80(100)7.15(73)
0.83(8.5)1.67(17)2.06(21)1.17(12)2.45(25)3.04(31)3.62(37)1.66(17)3.43(35)4.31(44)5.19(53)2.84(29)4.31(44)5.78(59)7.15(73)5.00(51)7.45(76)
1.37(14)2.75(28)3.43(35)4.11(42)2.25(23)3.43(35)4.60(47)5.78(59)4.02(41)5.98(61)8.04(82)9.80(100)
1.18(12)2.25(23)2.87(29)3.43(35)1.86(19)2.84(29)3.82(39)4.80(49)3.33(34)5.00(51)6.76(69)8.43(86)
―[1.57(16)]1.96(20)―
1.27(13)1.96(20)2.65(27)3.33(34)2.25(23)3.43(35)4.60(47)5.78(59)4.60(47)6.96(71)9.31(95)9.80(100)
1.08(11)1.56(16)2.16(22)2.65(27)1.86(19)2.74(28)3.73(38)4.60(47)3.72(38)5.58(57)7.45(76)9.31(95)
0.66(6.8)0.98(10)1.27(13)1.66(17)1.07(11)1.67(17)2.25(23)2.84(29)2.25(23)3.43(35)4.60(47)5.78(59)
0.79(8.1)1.18(12)1.57(16)1.96(20)1.56(16)2.35(24)3.13(32)3.92(40)
9.80(100)
【Note】When tight shut off(T.S.O.:0.001% or 0.002%)is requied for On-Off port or Throttle port for Type BS, Allowable Shut-Off Pressure shall be
multiplied by 1/1.2 from the table above.
Model 83A-BS & 83A-BSH
83ABSBSH
9
【Notes】(1) portion shows standard combination of valve Body and Actuator.
(2)The Unit of off-balance is kPaG(kgf/cm2G).(3)On type BS, Actuator Size N40, Off-balance 80kPaaG(0.8 kgf/cm2G), above Shut-off Pressure is not applicable for reverse action Type with
rated travel 65mm.
(4)Shut-off pressure of this table shows the value only with standard gland packing.(P4519+V7010)(5)On Bellow Seal Bonnet valve, Allowable Shut-Off Pressure is differed from above table because of Bellows effective area.
(6)Off-Balance 120kPaG(1.2kgf/cm2G)is not applicable for Actuator N40 with rated travel 65mm.
(7)Actuator size N33S & N40 with Off-Balance 120kPaG(1.2kgf/cm2G)is only applicable for type CQ-BS and CQ-BSH.
(8)On Model 83A-BS, seat leakage class V and Off-balanse 40kPaaG(0.4kgf/cm2G)is not applicable.
On Model 83A-BSH, Off-balanse is not applicable lower than 60kPaaG(0.6kgf/cm2G).(9)When Off-Balance is 100kPaaG(1.0kgf/cm2G)on reverse action actuator size 500~650X, Spring Range may differs by actuator size and
valve rated travel.
(10)Off-Balance 100kPaG(1.0kgf/cm2G)is not applicable for reverse action actuator size 500S rated travel 65mm.
Actuator size 500L should be selected.
(11)For Model 83BS, seat leakage class V and for "Use no oil" application, smallest actuator size is N33S.
■BSH
80(0.8)100(1.0)
80(0.8)100(1.0)120(1.2)
80(0.8)100(1.0)120(1.2)
80(0.8)100(1.0)
80(0.8)100(1.0)
80(0.8)100(1.0)
3.53(36)4.51(46)5.39(55)6.86(70)8.33(85)7.74(79)
9.80(100)
2.35(24)3.04(31)3.62(37)4.70(48)5.68(59)5.29(54)6.76(69)8.23(84)9.21(94)9.80(100)
3.04(31)3.92(40)4.80(49)4.51(46)5.87(59)6.96(71)7.84(80)
9.80(100)
2.05(21)2.64(27)3.23(33)3.04(31)3.92(40)4.80(49)5.39(55)6.76(69)9.61(98)9.80(100)
2.35(24)3.04(31)3.72(38)4.21(43)5.39(55)7.64(78)9.70(99)
1.86(19)2.45(25)3.04(31)3.43(35)4.41(45)6.37(65)8.04(82)
2.25(23)2.94(30)4.21(43)5.39(55)8.92(91)9.80(100)
1.76(18)2.25(23)3.33(34)4.31(44)7.06(72)8.92(91)
2.05(21)2.64(27)4.31(44)5.49(56)
1.37(14)1.76(18)2.94(30)3.72(38)
Unit:MPa(kgf/cm2)
Body SizeOff-balance
50(mm) 652(in.)
ActuatorSize 2 1/2
803
1004
1255
1506
2008
25010
30012
35014
N28
N33S
N40
500
650
650X
(2)Allowable Seat Leakage Ratio:ANSI/FCI ClassⅤ(Oprion)
Body SizeOff-balance
50(mm) 652(in.)
ActuatorSize 2 1/2
803
1004
1255
1506
2008
25010
30012
35014
N28
N33S
N40
500
650
650X
80(0.8)100(1.0)80(0.8)
100(1.0)120(1.2)80(0.8)
100(1.0)120(1.2)60(0.6)80(0.8)
100(1.0)60(0.6)80(0.8)
100(1.0)60(0.6)80(0.8)
100(1.0)
3.23(33)4.11(42)4.90(50)6.08(62)7.35(75)6.86(70)8.62(88)9.80(100)8.62(88)
9.80(100)
2.25(23)2.84(29)3.33(34)4.21(43)5.00(51)4.80(49)5.88(60)
7.15(73)
7.94(81)9.80(100)
2.94(30)3.62(37)4.41(45)4.02(41)5.09(52)
6.17(63)
6.86(70)8.62(88)9.02(92)
9.80(100)
1.96(20)2.45(25)2.94(30)2.84(29)3.53(36)
4.31(44)
4.80(49)5.88(60)6.17(63)8.33(85)9.80(100)
2.25(23)2.84(29)3.43(35)3.43(35)3.82(39)4.80(49)4.90(50)6.66(68)8.33(85)
2.84(29)―
3.13(32)3.92(40)4.11(42)5.58(57)6.96(71)
2.84(29)3.82(39)4.80(49)5.78(59)7.74(79)8.13(83)
―3.04(31)3.82(39)4.60(47)6.17(63)7.74(79)
2.84(29)3.82(39)4.80(49)
――
3.23(33)
Unit:MPa(kgf/cm2)
Model 83A-BS & 83A-BSH
83A BSBSH
10
Face-to-face Dimension
50mm or less:SW
60mm or more:BWASME 600 RJ
JIS 30 K 40 K RFASME 300 RJASME 600 RF
JIS 20 K
ASME 300 RF
JIS 10 K
ASME 150 RF(mm) (In.)506580
100125150200250300350
22 1/2
34568
101214
254276298352403451543673737889
267292317368425473568708775927
286311337394457508610752819972
289314340397460511613755822975
32038043049058063080091010301150
Press. Rating
Valve Size
9. MAIN DIMENSIONS AND WEIGHT
1 Face-to-face Dimensions of Valve
【Notes】(1)Face-to-face dimension in shaded zone conform to IEC 534-3(JIS B2002)and ISA-S75.03.
(2)Face-to-face dimensions of male and female, tongue and groove flange for JIS 10K-30K(ASME 150, ASME 300)
are identical JIS 30K RF.
Unit:mm
2 Weight
【Notes】The masses of actuator size 500S/L and 650S/L and 650XS/XL show only for direct action.
Valve Size(mm)
(In.)
Press. Rating
Bonnet Type ActuatorSize
Plain Bonnet
ExtensionBonnet -F
N28
N33S
N40
500S
650S
N28
N33S
N40
500S
650S
Valve Size(mm)
(In.)
Press. Rating
Bonnet Type ActuatorSize
Plain Bonnet
ExtensionBonnet -F
N40
500S
500L
650S
650L
650XS
650XL
N40
500S
500L
650S
650L
650XS
650XL
49
58
86
120
57
66
94
128
59
68
96
130
68
77
105
139
75
84
109
143
331
78
87
112
146
334
91
100
125
159
347
101
110
135
169
357
109
118
143
177
365
142
151
176
210
398
175
211
399
189
225
413
244
280
468
220
256
444
245
281
469
265
301
489
55
64
92
126
63
72
100
134
66
75
103
137
75
84
112
146
93
120
154
342
96
123
157
345
109
135
169
357
118
145
179
367
126
153
187
375
159
186
220
408
187
213
401
201
237
425
256
292
480
233
269
457
258
294
482
278
314
502
260
294
-
479
574
300
336
-
521
616
360
396
-
581
676
410
-
583
-
703
457
-
630
-
750
554
-
727
-
847
579
-
752
-
872
644
-
817
-
937
774
-
947
-
1067
950
-
1070
1042
-
1162
1234
-
1354
268
302
-
487
582
308
344
-
529
624
368
404
-
589
684
418
-
583
703
465
-
630
750
562
-
727
847
587
-
752
872
652
-
817
937
782
-
947
1067
950
1070
1042
1162
1234
1354
Unit:Kg50
2
10K
ASME150
20,30,40K
ASME 300,600
65
21/2
10K
ASME 150
20,30,40K
ASME 300,600
80
3
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
100
4
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
125
5
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
150
6
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
200
8
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
250
10
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
300
12
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
350
14
10K
ASME 150
20K
ASME 300
30,40K
ASME 600
Model 83A-BS & 83A-BSH
11
3 Standard Dimensions
83ABSBSH
【Notes】(1)Dimension C shows for Direct Action. For Reverse Action Actuator N28-N40, add 25mm.
(2)Dimension C for Actuator 500S, 500L, 650S and 650L Reverse Action, add CR dimension.
(3)E dimension for Valve size 80mm, upper shows for class 150-300 Ib and lower shows 400-600 Ib.
(4)Dimension S shows after dismantling Actuator.
Without Side-mounted Handwheel With Side-mounted Handwheel
Flow Direction
Flow Direction
Positioner
Flow Direction
Flow Direction
PositionerSide-mountedHandwheel
10. MOUNTING ORIENTATIONS
Standard mounting orientations are as follows.
■ Plain Bonnet Type ■ Extension Bonnet Type(Type-F, Type-H)
N28~N40 N28~N40
Actuator Siz
■ Bellows Seal Bonnet Type
500~650X 500~650X N28~N40 500~650X
Unit:mm
Valve Size ActuatorSize
N28N33SN40500SN28
N33SN40500SN28
N33SN40500S650SN28
N33SN40500S650SN40
500S650SN40500S650SN40
500S650S
650XS500L650L
650XL500L650L
650XL650L
650XL
507562715934553608761980554609762981
1277592647800
10191315828
10471343856
10751371965
11801480195512851595220613801690230117402347
D
280330400500280330400500280330400500650280330400500650400500650400500650400500
650
500
650
500
650
650
EG C
Plain Bonnet
G CType-F Type-H CR Note(2) S Note(4)
G C G C G C
Bellows Seal Bonnet Welded TypeBA20K, 30K BA40K
(mm)
50 2 95171
200
217
246
218
247
256
285
313
341
446
462
557
603
657712865
1084703758911
1130704759912
11311427742797950
11691465978
11971493100612251521111213331628210514331748235615291844245218902498
321
350
367
396
368
397
406
435
463
491
597
612
707
753
496
576
624
704
625
705
716
663
743
754
867
872
895
900
1164
1189
-
-
-
-
-
-
-
-
-
-
-
-
832887
10191310960
101512191438961
1016122014391746999
10541258147717841382160119021410162919301679189822192698
443
524
550
631
551
632
643
589
670
681
759
764
784
801
1019
1044
779834
10391258886941
11461365887942
114713661673925980
1185140417111274149317941299151818311534175320742553
735-
160
-
160
-
160250
-
160250-
160250-
160250-
160250300145
300
145
300
300
801
753
847
807
873
845
911
939
967
1149
1164
1222
1302
107011251316153510891144133415531157121214271646176411841239145416731969147516941990150417232019166418832179265819842297290820422355296624353046
220240350370220240350370220240350370380220240350370380350370380350370380350370380410370410480370410480410480
106
130/135
145
180
205
225
270
290
320
65 2 1/2
80 3
100 4
125 5
150 6
200 8
250 10
300 12
350 14
(inch)
Extension Bonnet
Bu
htt
M
●販東
大
国
札
東大 衡
上上 越
関千 葉
静
名中 部
阪 神
徳周 南
四新 居
大大 分
●海本山 ●海中国
●SAO
D
●OMG
●OC
◆当
◆Th
12
lletin No.MC
tp://www.m
本 社
Main Office &
販売・サービスネ京 支
阪 支
際 営 業
幌 営 業
北 営 業衡 サ ー ビ ス セ ン
越 営 業越 サ ー ビ ス セ ン
東 営 業葉 サ ー ビ ス セ ン
岡 営 業
古 屋 営 業部 サ ー ビ ス セ ン
神 サービスセン
山 営 業南 サ ー ビ ス セ ン
国 営 業居 浜 サービスセン
分 営 業分 サ ー ビ ス セ ン
海外関連会社 山阀门(大連)有限
海外販売代理店国、韓国、台湾、シ
ALES AND SUOverseas Marke
Domestic Sales B
OVERSEAS AFFMOTOYAMA VAGangxing Street
OVERSEAS NETChina, Korea, Ta
当社は保証期間を
he product will
■本カタログの記
■MOTOYAMA
subject to ch
■本カタログは正
■This catalog
product.
2
E‐B4307E
otoyama‐cp.
工 場 〒9
E‐m
Factory
5‐2TELE‐m
ネットワーク 店 〒210-
店 〒550-
部 〒210-
所 〒001-
所 タ ー
〒981-
所タ ー
〒942-
所タ ー
〒290-
所 〒422-
業 所タ ー
〒481-
ター 〒560-
所タ ー
〒745-
所ンター
〒792-
所タ ー
〒870-
限公司 〒11660
店
ンガポール、イン
PPORT NETWeting & Sales De
Branches : Toky
FILIATED COMALVE (DALIAN) 39‐14‐7, Jinzho
TWORK aiwan, Singapor
を原則として製品
be warranted f
記載内容は、商品
is continuously
hange without
正しい情報の提供
is supplied for i
.co.jp
981-3697 宮mail : info@mo
, Ohira Aza KaL +81‐22‐344‐4mail : info‐over
0007 神奈川県
0014 大阪市西
0007 神奈川県
0912 札幌市北リバティタ
3697 宮城県黒
0036 新潟県上
0046 千葉県市
8033 静岡市駿
0012 愛知県北
0894 大阪府豊
0861 山口県周
0896 愛媛県新
0108 大分市大
01 中国 遼寧省大
ドネシア、マレーシ
WORKept. : 11th Floo
yo, Osaka, Sapp
MPANY ) CO., LTD ou New District
re, Indonesia, M
納入後1年として
for one year aft
品の改良等のため
y improving and
notice.
供を目的としたも
information pu
宮城県黒川郡大otoyama‐cp.co
ameoka, Ohira4511 / FAX +8rseas@motoy
川崎市川崎区駅前
西区北堀江 1 丁目
川崎市川崎区駅前
北区新琴似12条7タウンP棟101号
黒川郡大衡村大衡
上越市大字東中島
市原市岩崎西1丁
駿河区登呂2丁目
北名古屋市久地野
豊中市勝部2丁目
周南市新地1丁目
新居浜市阿島1丁
大字三佐字山ノ神
大連市金州新区港
シア、サウジアラビ
r, Clie Kawasak
poro, Tohoku, Jo
t, Dalian‐city, 1
Malaysia, Saudi
ています。
ter delivering th
め予告なく変更す
d upgrading its
のであり、本製品
rpose only and
大衡村大衡字亀o.jp
a‐mura, Kurok81‐22‐344‐452yama‐cp.co.jp
前本町 10-5 クリ
目 12-19 クリモ
前本町 10-5 クリ
7丁目1-47
衡字亀岡 5-2
島2393番地
丁目5-19
目10-13 ハイツ富
野安田36番地
目18-3
目6-11
丁目6-26
神980-1
港興大街 39 号 14
ビア
ki, 10‐5, Ekimae
oetsu, Kanto, S
16601 China
Arabia
his product in p
することがあります
product design
品の市場性または
should not be
亀岡5-2 TE
kawa‐gun, Miy22
リエ川崎 11F
モトビル 3F
リエ川崎 11F
富士1F
4-7 TEL
‐honcho, Kawa
TEL: +81Shizuoka, Nagoy
TEL: +86
principle.
すので予めご了承
n, specifications
は適合性の保証を
considered cer
L(022)344‐45
yagi, 981‐3697
TEL(044)381
TEL(06)6535
TEL(044)38
TEL(011)766
TEL(022)344
TEL(025)542
TEL(0436)2
TEL(054)288
TEL(0568)26
TEL(06)6854
TEL(0834)2
TEL(0897)47
TEL(097)527
L +86-411-658
saki‐ku, Kawasa
1‐44‐381‐8771 ya, Hanshin, To
‐411‐6589‐127
承下さい。
s and/or dimen
を証明するもので
rtified marketab
511(代表) /
7, Japan
-8770(代表)
5-8111(代表)
1-8771
6-1520
4-1761
2-5151
1-4400
8-2237
6-6681
4-7511
1-5012
7-8993
7-3704
89-1277 FAX
aki‐city, Kanaga
FAX : okuyama, Shiko
77 FAX: +
sions. Informat
ではありません。
bility and confo
FAX(022)344
FAX(044)38
FAX(06)653
FAX(044)38
FAX(011)76
FAX(022)34
FAX(025)54
FAX(0436)2
FAX(054)28
FAX(0568)2
FAX(06)685
FAX(0834)3
FAX(0897)4
FAX(097)52
X +86-411-658
awa, 210‐0007
+81‐44‐381‐87ku, Oita
+86‐411‐6589‐1
tion included he
ormability of thi
20210
4‐4522
1-8772
5-8655
1-8773
6-1521
4-1762
2-5152
1-3540
8-2239
6-6631
4-7512
1-0450
7-8995
2-2352
9-1278
Japan
73
1278
erein is
is
2 MSP