mod 13-kiln volatiles.pdf
TRANSCRIPT
Process EngineeringTraining Program
MODULE 13Kiln Volatiles
Section Content
1 CETIC “Volatiles” Group- Final Progress Report
2 CETIC Sub Commission “Behavior of Volatile Material in Kiln Systems
3 Investigation into Potential Low Temperature Volatilization
4 Factors Affecting Sulphate and Alkali Cycles in Rotary Kilns
5 Alkali Volatilization- A Review of Literature Available in 1977
6 A Study in the Volatile Cycles on HOPE # 2 kiln
7 Design and Experience with Bypasses for Chloride, Sulphate, and Alkalis
8 Kiln Gas Bleed Considerations
9 Ring Formations in Cement Kilns
10 Kiln Build-Up Meeting
11 Cement Seminar- Rings, Balls, and Build-Ups
12 Ring and Buildups in Cement Kilns
HBM Process Engineering ConferenceMinimization of Volatile Cycles
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 1
CETIC “Volatiles” Group- FinalProgress Report
Blue Circle Indusuies PLC
Internal memo
3 SEE BELOW:-
‘rot? C P KERTON
Your re:: Date 21 December 1994
Copies
Stijec CETIC “VOLAl-IUS” GROUP - FINAL PROGRESS REPORT
Herewith a copy of an English version of the final report from the CETIC GOUPwhich worked from 1990-1992, initially inspired by 3lue Circle’s initiatives.Copies of various French documents exchanged within the group are availablefrom me or from Cb.ris Hoit.
The text follows the order of the French original, intended for those who tookpart in the work. For those who have not been following progress so closely, thelogical order of reading would be to stan with Appendix 2, which is a publishedpaper based on the initial work of the group on cycles of chlorides, sulfates andalkalis driven from the burning zone. Next comes Appendix 3, which isTom Lowe-s’ account of some practical applications of these concepts whenburning petroleum coke. Returning then to the start of the main text, there is anaccount of further discussions and activity on this topic leading finally to
Appendix 1 which looks at capture of SO:, in colder parts of a kiln system. (Thoseconcerned soleIy with pollution abatemerit might well start here!)
Proposals for possible further work are listed and those relating to sulfurbehaviour will be pursued by joint exchanges of experiences from 1995.
Suggestions for further distribution within Blue Circle will be welcomed.
cf&L
I&,/ >c P KertonPatent & Information Service
Eric
To: ;P L Rover (2 copies)C P B ‘Turner
T M LowesC J HoltL P EvansR M MutterJ M LawtonP A Longman
ca: \?%+!\2112CETIC
Blue Circle Technical Centre
TC 94 049
CEl-lC SlJB-CO-ON
“BEHAVlOUR O F VOLATILE M A - IN KILNS”
FINAL. PROGFZES REPORT
MAY 1994
This report is strictly confidential within the Blue Circle Group.
Additional copies should not be released outside Blue Circle
without reference to the Technical Cenme.
Please apply to the hformation Servicesat tie adcks give0 below.
September 1994
S U M M A R Y
Together with an earlier report (ISTN 92/5) this text sets down the major findings of a
group which met from 1990 to 1993. For minor components volatilised in the burning
zone (alkalis and sulfates), there are several successes on production kilns in reducing
volatile cycles by attention to burning zone conditions, especially in relation to
chemical decomposition of C&I,. Correct diagnosis of conditions is assisted by
improvements to permanent on-line exit gas monitors and to suitable standardisation of
sampling procedures for dry process kiln enuy material. The full effects of dust cycles
in confusing results of sampling exercises remain to be established.
Sulfur volatilisation and absorption at lower temperatures have also been considered and
the conditions of temperature and atmosphere which aid reactions for SO2 capture by
various materials are outlined. Various permutations of actions are possible to abate
emissions and some will not succeed at all points in a production line or may require
moisture addition or increased residence time to improve their effectiveness.
Proposals for possible topics to continue this work are listed. (This is an English version
of the official French text).
=C O N T E X T S
Paee No
1 . Introduction
2 . Task of the Sub-Commission
3 . Cycles of minor elements generatedin the burning zone
4 . “Cold” cycles of minor elements
3. Trace elements
6. Future work
Figures
Appendix 1 SO? CAPTUREChknical IMechanisms far Sulfur Dioxide Absorption in CementKilns and other Industrial Abatement Plant.
Appendix 2
Appendix 3
1 1
14
15
TEXT FRO,M INTERNATIONAL SYMPOSIUM ON GASCL&WING AT HIGH TEMPERATURES.Behaviour of Volatile Materials in Cement Kiln Systems.
PAPER PRESENTED BY T M L0WE.S100% Pet Coke - Problems and Solutions.
1 . INTRODUCTION
The group has the following memberx-
HOLDERBANK
3LUE CIRCLE
CIMENTS LAFARGE
P BORKI
P KERTON (Animateur)/C HOLT
M DANDINE/K 30ULOT/M TOUSSSAINT/X DUPONT-WAVRLN
CIMENTS FRANCAIS B POLGE/G Bw BERGERY/G FLAMENT
ITALCEMENTI R TACCHINI’
C3R c MEYERS/J PARlSIS/P RENIER/M BRUYERE
CIMENTS D’OBOURG
ENCI
F LAMPROYEfR SPILLAERT
W VAN LOO/F ERE?JS
The foIlowing meetings too& place:-
1 . 1990 Autumn
2 . 1991 Spring
3 . 1991 Autumn
4 . 1992 Spring
5 . 1992 Autumn
6 . 1993 Spring
7 . 1993 Autumn
Maastricht
Greenhithe
St Antoing
Frangey
OrbY
Salerno
Obourg
ENCI
BLUE CIRCLE
CBWSCF
LAFARGE
HOLDERBANK
ITALCEMENTI
OBOURG
This year there was one meeting at Obourg on the 4 and 5 November 1993.
TC94049 2 Tt=chu.id Cease, .!%@cabm 1994
2 . TASK OF THE SUEKO~MMISSION
This is “to produce a state-of-the-art report concerning the behaviour of volatile
material in kilns.”
This work originates from
1 . The increased use of ail sorts of secondary raw materials and fuels.
2 . The trend to produce more low alkali cements.
3 . Emission regulations which are becoming more and more rigorous.
Furthermore, during the work, important implications for kiln output and cement quality
have been found in connection with control of cycles. Our principal recent activities
are covered under the three following headings, 3-5.
(A copy of an associated paper by T M Lowes is included at the end of this report,
having been presented at the same meeting in May 1994).
3. CYCLES OF MINOR ELEMENTS GENERATED IN THE BURNING ZONE
We have already produced a first text on “classical” knowledge for this group of cycles
(ISTN 92/5): this was distributed in 1992. Supplementary work is described here.
Given a sample of material and its chemical analysis, one might think that all would
become clear, but to calculate a chemical balance, it is also necessary to know the mass
flows which are involved in the calculation, and there are a number of methods of
deciding upon these. Each method has its own advantages and disadvantages, making
them more (or less) appropriate at different points in the burning line. It is important
to note that
1. In the past this sophistication has not generally been adopted
2. Various flow rates for hot raw meal entering the kiln can be calculated by
different means, each one giving a different “burning zone volatility”.
We have continued exchanges on these topics to improve our understanding. One
important parameter in the calculations is the flow rates of entrained solid particles
between preheater stages, in particular between the kiln and the preheater tower.
There are not many results available for this parameter (we note that there are not
always the same sets of results available to explain observations!).
As far as these “classical” cycles of minor elements are concerned, there is much
activity within member companies at present There are two fields of particular
interest:
Firstly, the characterisation and the behaviour of hot raw meal (including the use Of
modified geometry cyclones and special linings), and secondly the influence of
combustion and heat transfer on volatalisation - especially in the burning zone but also
in precalciners. The influence of the local atmosphere close to clinker granules in the
rc94049 4 TecbniGai Came. SenM I994
burning zone seems to play an even greater role than had been thought in the past:
there are several results where volatilisation has been significantly reduced by more or
less simple means (additional oxygen) and we trust that one day there will be a
somewhat deeper understanding than indicated in our previous report. This
understanding will also help us in applying results from the mathematical analysis of
cycles from CBR which has shown great variations in alkali and sulfate volatilities in
the burning zone in different kilns (even when taking account of the major volatilisation
of chloride which explains a proportion of these differences).
This year we have tried to bring together knowledge on:
The most recent studies on control of cycles and characterising hot raw meal
on the industrial scale;
Mathematical analysis of cycles and cyclone performance (from chemical
analysis of samples);
The effects of the flame and kiln atmosphere ‘on volatility, especially when
using petroleum coke.
Study of free energies indicates the compounds expected and which of them are the
most stable in the prevaiiing conditions of temperature, pressure and composition of the
solid liquid and gaseous phases. Mr Berard-Bergery distributed a summary of the talk
which he previously gave on this aspect of thermodynamics, He notes that without a
certain knowledge of this subject it is difficult to make progress, given the need to
explain the apparently contradictory results obtained from operating kilns. (We must
certainly bear in mind the fact that we need to consider dynamic equilibria, not only
static systems.) Thermodynamics allow us to determine the direction, intensity and
speed of transformations of physical systems as a function of conditions. The possibility
of a reaction is known from calculating the change in (Gibbs) free energy, if operating
at constant temperature and volume or of free enthalpy at constant temperature and
pressure. Examining the trend of this value as a function of temperature, the reactions
of formation or decomposition of a single chemical compound can be considered, and
the order of stability in a family of compounds (chlorides, fluorides, sulfates etc) can
be deduced. Hence, the reactions between one element and the compound of another
element can be foreseen. There are quite a number of diagrams of free enthalpy as a
function of temperature available (determined in the field of metallurgy) and also
information on partial vapour pressures which influence the equilibria.
Along a burning line it can be seen that for chlorides KCI is the most stable and easily
vaporises producing a chloride cycle. For fluorides CaF2 is the most stable at all
temperatures, and does not easily vaporise. For fluorides, phenomena are therefore
very different for those encountered with chlorides. For sulfates K2SO4 is by far the
most stable and CaSO4 the least. For C&30, stability also depends among other things
on the partial pressure of oxygen, so that the sulfate cycle brought about by the
decomposition and re-combination of &SO4 will be very different depending on the
oxidation/reduction conditions at different points along a burning line. Na20 is more
stable than f(20 and is found in clinker combined in the aluminate phase, whilst K20
tends to form &SO, if possible. It is interesting to see that sulfur, for example in the
form of SO,, can be captured by carbonates because sulfates are more stable. At low
temperatures sulfites can also be obtained.
CIMENTS FRANCAIS note that it is necessary to define the conditions in which a kiln
must operate to give the desired results, in the case of high fluxes of sulfur or alkali.
Results from CC3 confirm these ideas and they are being applied in other Works. Mr
Flament has told us that the text which he presented at the Berlin Congress gives a
good summary of his experiences at CCB.
At CCB, using 100% petroleum coke (ore-calcination with separate air at around 55-60%
kcal) a good kiln output is found when there is a higher and more constant oxygen level
at the kiln exit (1.5 - 2.0%), a greater fuel fineness (residue 3.6% compared with 5.0%),
a more stable flame shape, and a less severe burning regime - obtained by means Of an
examination and adjustment of geometry in the burner region. The geometrical aspect
helps to avoid too high a dust cycle (including cooler dust) and flushes, which can both
cause alkali capture and blockages (contrary to the ideas of certain plant suppliers).
&SO4 nodules are found in the interstitial clinker phase, and there is a need to consider
quality aspects further. There is a sulfate: alkali ratio of 3.5, which is acceptable in
the stable kiln regime: thus it is preferred to use only 50% petroleum coke for
production purposes, so as to reduce the possibility of entering into a potentially
difficult state. Coke brings 26% of the sulfur arriving in the kiln system.
The sulfate/alkali ratio is an important parameter to take into account, but it is not the
only one. It is also necessary to have a good and continuous analysis of kiln exit gases
to allow combustion conditions to be followed. It is preferable that gas analysis is
automatically corrected for oxygen level so as to indicate other changes more clearly.
It is equally necessary to continuously monitor precalciner combustion conditions by
means of supplementary analysis of relevant compounds in the gas phase.
The “intensity of combustion” in the burning zone is an important factor to understand
and use to control events. The decomposition of CaSO, in a reducing atmosphere is the
key mechanism. Each kiln has its appropriate oxygen level in the kiln exit gases, which
must be respected for a given sulfate input. The word “volatile” can lead some people
into error: whilst KCl and NaCl are present in the form of gaseous molecules,
thermodynamics indicates that K20 and Na,O decompose in the flame and re-combine
later. It can be useful to separately tabulate the calculated volatilities of KCl NaCl,
K$S02, NaSO,, CaSO, instead of only Cl, K,O, NaZO, SO3.
We have discussed the design and operation of by-passes, certain of which take a
significant dust burden at the kiln exit, which brings about difficulties in operation. In
Ciments Francais kilns the range of dust burdens is from some ZOO-1,000 kg of dust per
tonne of clinker. This dust burden reduces the performance of the lowest cyclone: if
the value of the dust burden is not known it can be difficult to interpret results. (It was
noted that Weber recorded low dust burdens in all the kilns which he analysed) Other
important parameters which must be known in order to diagnose a situation are the
chemical analyses of good samples of coal and of the hot material coming into the kiln
at the feed chute level.
Given the above-mentioned data, the measurement of CO? level at the kiln exit over
a certain period allows separate calculation of decarbonisation in the kiln and the
preheater/precalciner. The mixture of dust and new raw meal which comes into the kiln
can then be estimated from the loss on ignition. It is suggested that methods using
chemical tracers to estimate the material flow, for example K,O, can be falsified if the
level of dust cycle is not known.
It seems probable that the geometry of a plant has a marked effect on dust
entrainment. In the older generations of Dopol preheater, material fell a long distance
from the bottom cyclone into the kiln. The kiln entry material had a low loss of
ignition which could be falsely attributed to good decarbonisation. The more recent
Dopols have a side entry for material: a bypass can then expect to encounter a lower
dust burden. The older “lateral centrifuge” entry of F L Smidth also produces a poor
bypass efficiency, due to dust entrainment. High dust recycle levels also have the
inconvenience of increasing the probability of blockage
(Mr DuPont-Wavrin noted that the Berthold Company is supplying an X-ray detector t o
monitor material flow rates ex-cyclone).
It is useful to calculate the effect of dust cycles on thermal performance. A heat and
mass balance for each preheater stage allows the effect of dip tube geometry changes
to be observed. Opinions vary as to the appropriate choice for different stages, not to
mention the use or removal of cyclone exit flaps.
A variety of experiences have been reported regarding Hasle Vortex Finders. At ENCI,
excellent results have been recorded for over 3 years, whilst at CBR the tubes were lost
in 3 months- Ciments Francais have observed the same range of lifetimes. There is
consensus on the advantages of dense ceramic Hasle units in the kiln feed chute (with
a minimum of exposed refractory cement?,” when they are set up with a good
arrangement of air cannons. Some peopie have doubts as to their sensitivity to thermal
shock in other regions of kilns during heating and cooling.
ITALCEMENTI has described similar experience with a F L Smidth chloride bypass at
Picton, also used to assist the production of low alkali clinker. Here the high dust
burden (some 1,000 kg per tonne) causes the so-called “gas bypass” to have tbe
efficiency of a dust bypass. Tests are in hand at Nazareth with a purifier which
removes SO, by injection of raw meal and water (a Monsanto design). At Colaferro two
geometrically identical preheater kilns produce respectively some 1,900 and 1,150
tonnes a day. The higher output kiln is fired with a mixture of coke and coal and
produces build-up problems, whilst the other operates satisfactorily with 100%
petroleum coke. The only difference that has been noted in combustion conditions is
a higher secondary air temperature due to the use of IKN plates in the Fuller cooler.
Italcementi manages to use 100% petroleum coke on the Lepol process, even with 10%
over-grate firing, with emissions of SO, - except during build-up losses - having only
pyritic material as origin. The residue is 10% as for coal. On the dry process it is
necessary to drop the residue to 4% (or 5% for a coal/coke mixture). The precalciner
gas does not contain any SO2 when coke is used in the burning zone. The sulfur leaves
with the clinker, partly during occasional flushes.
In the past coke or anthracite was introduced into long granule-fed kilns. This helped
formation of a good burning zone, but nowadays it is found that there is also a high SO2
emission. This coke is now added to the main burner, a procedure which operates
satisfactorily if the burning zone is controlled via NO, monitoring to avoid the problems
which can be caused by the sudden arrival in the burning zone of build-ups detached
from internal cruciforms.
In the same way, LAFARGE has continued with a major programme of geometric
"centralisation" of burners, noting oxygen levels (typically some 3%) and SO, levels ex-
73.i~ re-sort Ls soicrlr confidemial w.rhio the Blue Ctie Group.
kiln as a function of flame momentum. Several Works keep the centralising mechanisms
on the kiln platform so that alignment can be corrected if there are changes after some
weeks of operation. In such circumstances 100% coke can be used (3-5% S) on the dry
process with a 5-10% residue.
Automatic kiln entry material sampling systems are generally installed with a view to
assuring safe operation (Pfaff) and Lafarge gave an account of an in-depth study at Port
la Nouvelle. The company was particularly interested in the impact of sampling
techniques on results. Here, there is a kiln fed at some 100 tonnes an hour (50% of the
heat energy coming from petroleum coke) with 3% oxygen ex-kiln. The levels of all
volatiles in the collected dust go down as a function of sample suction rate, reaching
a plateau. The dust Is really a mixture of fine material (high in volatiles and easy to
collect) and coarse material. Although the nominal isokinetic aspiration rate for the
probe was some 30 litres per second, it was not aligned with the gas fIow direction and
higher suction rates were therefore needed to obtain a representative sample.
Lafarge express the hope that a standard method can be written up, suitable for use
throughout the world. They have currently only two or three competent sampling teams
in their French group. It was noted that it is a bad practice to make use of large probes
and low capacity pumps to reduce blockages as far as possible.
CBR reported on SO2 levels in the kiln system at Antoing. The level of some thousands
ppm ex-preheater drops to 600 ppm at the stack. This loss is split 20% to the crusher,
20% to the mill and 60% to inleaking air. It was reported that at Rekingen the raw mill
is run at a reduced throughput, in order to allow SO2 capture t o continue throughout the
operating day.
A few supplementary results from the simplified mathematical model have been
distributed, with its application to the analyses of balance samples from various member
companies, so that volatilisation, entrainment and capture coefficients can be
calculated together with the performance of some cyclones.
ThLs remrr Ls snicdy codid~riaf w-if&in tie Blue CLv!e Grarw.
A significant range of values was noted, all calculated on the same basis. K20 is a good
tracer to determine raw meal entrainment by gases. For the calculated entrainment
values in the document distributed, one must consider the position and methods used to
collect the kiln exit dust samples - with a probe in the kiln, in the riser duct or ex-
bypass. Nevertheless we consider that it will be very useful to extend the tabIe of
results already obtained by sending further analyses to CBR to gather a common table
describing volatilities, An example of a Blue Circle kiln (poor flame with high
volatilisation) is the only one to have been added this year, and the model remains to
be more widely used.
At BLUE CIRCLE some thermodynamic data lead us to think that in a typical kiln gas
there is at llOO*C a sufficient reduction potential produced from 2,000 ppm of CO to
reduce CaSO, with a consequently much higher voiatility. A separate paper from Blue
Circle is appended, giving an account of UK experience with use of petroleum coke.
A paper from Blue Circle regarding the design of a bypass for a new Works with high
chloride raw materials was discussed. There was also an expected high content of
alkalis in the clinker, which could perhaps be reduced by the addition of even more
chloride. The performance of existing by-pass systems indicates that despite the fact
that (according to suppliers) there is a possible dust loss of some 200 to
250 g/Nm-’ in the gas extracted from the system it will be best to calculate with a
nominal level of 400 In such circumstances there will be a need for a raw meal
preparation system with a significantly higher throughput than normal.
Several remarks were made: there are examples of precalciners blocked by sulfur; the
handling of by-pass dust rich in CaCl, is much more difficult; is the fuel penalty per
percent of by-pass closer to 5% than the 1% used in this example? (This latter figure
was supplied by the company which intends constructing the proposed Works.)
The animateur was invited at short notice to give a paper during an International
Symposium of the Cleaning of Gases at High Temperatures in December 1993, which is
This remrr Ls sm’cr(;l cmfidemiai withiu tie Blue Cri-cle Group.
appended. Several specialist workers in this field have encountered problems of
blockages and build-ups which provoke their interest. (Note that data on the equilibrium
CO-CaSO~-CaS is given in "Sulphur Capture in Fluidised Bed Boilers: the Effect of
Reductive Decomposition of CS04”, by A Lyngfelt and B Leckner, Chemical Engineering
Journal, Volume 40. pages 59-69, 1989.)
4 . “COLD” CYCLES OF MINOR ELEMENTSLEMENTS
Information on the effect of internal cycles on emissions to the exterior has been
exchanged, avoiding (if possible) examination of equipment for capture of such emissions
which is left to the "Environment" sub-commission, liaising with its animateur. This
topic typically concerns cold cycles of SO2 formed at low temperatures in the
preheater, and capture of SO, emissions in long kilns and in the Lepol process involving
cycles which originated in the burning zone.
For this topic it seems that most information has already been treated by the
‘Environment” sub-commission: it remains to define more precisely the chemical
reactions which are involved and the domains in which these are the most (or the least)
effective. We are interested in establishing information about chemical efficiency of
absorption of SO2 as a function of conditions of atmosphere, humidity, temperature,
residence time, particle size, chemical composition etc.
The animateur noted the classification of absorption mechanisms given in two USA
papers: these concern tests carried out Davenport (Steuch) and at Lone-Star (Sheth)
The document sponsored by the British Pollution Inspectorate is also available. This
reviews published information on removal of trace gases. It covers a range of both
chemical species and reactive materials, The sections relating to SO2 capture appear
to provide a useful framework within which the cement industry’s experience can be
classified, see Appendix. Other industries are interested in the possible future use Of
sorbents with increased reactivity (cement kiln dust?) and in “regenerable” agents such
as calcium disilicate.
The reports of HOLDERBANK to the Environment Sub-Commission have indicated that
emissions of some 1,000 to 1500 mg/Nm3 of SO2 were reduced to close to 350 mg/Nm3
during the operation of the raw mill. The same effect could be obtained in direct
operation by the addition of Ca(OH)2 to the raw meal. This provides removal of 50%
SO2 at a stoichiometric level of 5; Polysius would suggest 80% removal at a ratio of
8. Not all users seem to have taken account of the need to use superstoichiometric
quantities of sorbents, which sometimes may react with only some 10% efficiency.
Work carried out in the UK by Lodge-Cottrell in the field of the electric power station
desulphurisation, has shown an efficiency of 25% for dry lime injection, rising to 50%
in the presence of moisture, and also that sodium based reagents had a genuine action
which was almost double that of calcium based sorbents (and that these could be
introduced as solutions by means of simple nozzles).
It was mentioned that Rekingen Works had modified its raw mill throughput so that it
operated 24 hours daily, thus capturing SO 3 to conform to emission regulations. The
Santa Cruz Works of Lonestar may do the same. In this class of activity, CIMENTS
FRANCAIS works on the basis of 50 to 75% absorption.
ENCI gave an account of experience with operation at different oxygen levels to reduce
SO2 emissions from its two-stage preheater kiln. The degree of sulfation of clinker at
Maastricht is 125%. This, along with other causes, produces an emission which must be
reduced to comply with new regulations During 3 weeks the oxygen level at the kiln
exit was altered from 1.5, 2.0, 2.5, 1.3, 2.0%. The results for SO2 level in the emitted
gases and SO3 in the raw meal and clinker are in agreement, showing that emissions can
be reduced. If the effects on quality and on kiln operation are acceptable, they intend
to buy new fans to guarantee sufficient oxygen level at maximum kiln output (with
fuzzy control). The re-installation of Magotteaux stirrers in the kiln has once again
given positive results after the last stop.
At OBOURG there is an emission problem similar to that at ENCI, which can be
resolved by a kiln exit oxygen level of 2 to 3 % but this could give a too high a chain
temperature and an unacceptable reduction in output. Oxygen has been added
(1,000 m3/h either by the primary air channel or beneath the flame) gaining 3 to 4
tonnes per hour of clinker at an acceptable chain temperature. The cost of oxygen is
some 3 Belgian Francs per cubic metre for a permanent irstailation, but this could be
This reqorr is snict(y confidential within the Blue Ckfe Group.
offset if cheaper (higher sulfur fuels can be used. It seems that at least a quarter, and
nore usually about a half of the SO2 disappears between the kiln and the stack, no
doubt by capture on dust. Given the large volume of gas produced by this wet process
kiln and its moist fuels, a new fan would be proportionately much more costly than for
ENCI.
At Obourg it seems likely that the longer kiln can satisfy emission limits through
control of excess air levels. For the other kiln, another method of reduction of peaks
of SO, is being studied; NaHCOS injection in the exit gas duct at the upper end of the
kiln. The trial installation from Solvay (about 400 kg/h of Na.I-IC03 powder) was leased
for longer trials. Chemical efficiency is 100%.
As already noted ITALCEMENTI is looking at a Monsanto system involving a water/meal
scrubber for SO,, with a cost expected to be only 20% for that of an “Untervaz” system-
LAFARGE has studied sulfur behaviour on a semi-wet Lepol grate. In the hot chamber
there is an excellent capture of sulfur coming from the kiln, but there is also
decomposition of pyritic sulfur on the grate. This starts at the transition from the cold
to the hot chamber (500-600'C) and is completed by the middle of the chamber.
TC9-4049 1 5 Tecfioical Centre. Senrember 1994
5. TRACE ELEMENTS
lTALCEMENTl has presented a summary of results from 30 kilns, seeking to determine
the amounts of 16 metals In stack dusts, and also of 5 inorganic micropollutants. At
Vibo works (precalciner), the raw meal is dosed with CaF2 to influence the
decomposition of strontium sulfate and so limit the undesired effects brought about by
SrO during alite formadon. On the Lepol process CaF2 also provides a less dusty
clinker and a reduced need for kiln system cleaning. No changes were noted in the
behaviour of other halogens or of alkalis.
OBOURG has provided, a list of balances over 2 years. BLUE CIRCLE has shown a
table for retention of various elements in a number of kilns as a percentage of the
quantity brought in by the kiln feed (including recycled dust). An examination of Blue
Circle’s conclusions regarding behaviour of trace elements considered elements as being
either non-volatile or partly volatile. 3-5 results were available for each element for
the wet, semi-wet and dry processes. The percentage of the input found in stack dust
was very low for the non-volatile elements (As, V and sometimes Cr - unless there was
enrichment from refractories), thus reflecting tie good efficiency of de-dusting and the
varied additional contributions from fuels. The highest proportions escaping with stack
dust were for cadmium, lead and thallium in semi-wet kilns. The levels noted were
influenced by the rate of removal of intemediate dusts produced in the kiln processes.
For the dry process there was less enrichment of cadmium and lead.
We have specifically looked at German work previously published in ZKG, where the
need to examine the chemical combination of elements is underlined. Mercury, for
example, must always be oxidised in a kiln system, so that the vapour pressure of the
uncombined element is not to be considered.
We have also received a supplement to the bibliographical list established in Autumn
1991, which concerns cold and trace element cycles. The published literature makes it
quite evident that cement kiIns are reputed to be potential origins of emissions of SO,,
Tl, Pb - and perhaps Cd and Hg, if these latter are found in the region. There is also
a certain interest in the upgrading of kiln dust,
TIC re,vrc is suictiv wnfide!zu*al’ witi tie BILE C’ric!e G~OLT.
TC94049 1 7 Techical Cam-e, ?&xBder i99d
FUTURE WORK
The Plenary session has asked for a new sub-commission to be set up in 1994/1995 to
follow the topics left from the existing group, with the addition of a study of corrosion
and the wider application of the mathematical model already developed. We must avoid
repetition of work already done, and coverage of subjects which the Maintenance Group
and the new Working Party on Flames are currently examining. (For corrosion,
depending on the activity of the Maintenance Sub-Commission, we might envisage a
search for methods of reducing its effects, as well as the identification of compounds
which have a strongly corrosive action).
Our group is convinced that there remains much to be gained for the companies of
CETIC in bringing together the specialists who are concerned with Chemical phenomena
within kiln systems and avoiding the study of topics which are more or less “legal”.
All are invited to consider a new division of chemical and engineering work with regard
to cycles, transport, clinkering, emissions, interaction with refractories, combustion,
sampling (gas and solid), etc etc.
A review by the Sub-Committee has produced a list of ideas, (see following page), these
points generally relate to factors which have an impact on quality, cycles, transport,
clinkering of emissions, refractory attack, combustion, sampiing of gas and solids etc.
Some of them are more relevant to groups in the Technical Commission. These ideas
remain for immediate discussion.
(NOTE : It was subsequently agreed to concentrate initially on topics related to the
behaviour of sulfur).
C P KertonTechnical CentreMay 1994.
LIST OF TOPICS
Environment:
Factors effecting organic emissions and their control.
Process:
Water injection in planetary coolers.
CO SO2, CaS04 balances.
Control of kiln build-ups and their chemical composition.
Effects of secondary firing on volatilisation/condensation in Lepol grates and
their control.
Methods of successful use of even higher levels of S in fuels.
IMethods allowing the retention of SO3 in clinker.
Control of chloride volatilisation.
Applications of CO, analysers.
Determination of dust cycles in kilns and heat and mass balances for each
preheater stage.
Optimum fineness of petroleum coke for kiln and precalciner burners.
Effects of volatile materials on the long term and short term stability of
kilns and their consequences for static and dynamic conuol strategies
(allowing early pro-active responses t o change).
Control strategies (anticipatory control) to restore operation of a disturbed
kiln (effect on throughput, environment, quality etc).
Bypass control.
Effects of geometry on cyclone operation.
Effects of volatile cycles and dust cycles on cyclone dip tubes and on various
refractories.
Control of sulfur cycles at low temperature.
Effects of heating and cooling on refractories and linings; success with rapid
regimes.
Effects of parameters other than CO on sulfur volatilisation.
Correlations of SO2 signals with other process parameters.
Effects of injecting and additional fuel at different points in the process (for
example solids at the kiln feed chute).
Distribution of trace elements throughout kiln systems, and methods of
control.
Interaction of volatiles and refractories.
Influence of SO3 on refractor+ life - both direct (chemical) and indirect
(perhaps a lower BZT).
Correlations between SOS and free lime in operating kilns.
Effects of V and Ni (coming from coke) on refractories.
Correct regulation for burners for different levels of coke fineness and coke
mixtures.
Maintenance:
Corrosion in colder zones of kilns (in relation to Cl and S)
Workplace hygiene and safety aspects from the point of view of volatiles
Product/Quality
Treatment and use of dust rich in volatiles
Methods for the internal use and/or upgrading of dusts which cannot be
dumped.
Effects of V and Ni (coming from coke).
Effects of SO3 and of sulfate/alkali ratio on clinker quality at different
levels of free-lime (is there an optimum level?)
Effects of marginally reducing conditions on quality.
Effects of halogens on cement behaviour (standards, etc).
Effect of clinker size grading on quality.
cix/tla13.9.94&4:x94.049
RT lo9 pot 1 b.Col)
:A-.L--- -L--Ii---.1; -_1I.
Tempercrure “t
0 2 0 0 coo 6 0 0 6 0 0 I0co 1209 ISGO I~0 la^OO
-/.zuqo 5-l. :uq,sa
-157iForrrn.e I
i .I...
j-2
oxides.
. f
( .*
--
i;‘:
* . . . ; .-
... --I- J,
,
.--
kl..,*--l---*-l.,-~
l“““I ***-I---*!~
i---I “-i-y”---I~
--l--
0L(I
: Ill1 III I Ill1LUU 4uu Eta BOO 1000 1200 -Pm 7600
Free cncrg diagram for sulfates.
-20I I / I i 8
I
I j j ; j! i : i ,
11
T2mgrz!lLii2, Y
fret energy diasram ior chiorid:s.
I
-no -
Tempcraturc,=C
Fret cncrgy diagram for fluorides.
\\
. .
t
\
‘,
j I i L ! -
- -
450
400
350
3 0 0
zso
2 0 0
7.50
1 0 0
‘s 0
0 L
20 30 40 SO 60 7 0 8 0 90 1 0 0 110 1 2 0 13*Dhbor <l/mn>
3-90 - -43.447 + 4.042 * ~&bor <i/mn); R-t - .a65
Km so3 Cl
<125fr 13 5.2 7.29
>125p 4.3 1.9 1.6
Ensemble 12.6 4.95 7.03
45op 3.6 4.4 2.3
>lSOp 3.1 0.8
Ensmble 5.3 4.2 2.1
Cl : 2.1 2.3 0.7
450
400
350
3 0 0
zso
2 0 0
7.50
1 0 0
‘s 0
0 L
20 30 40 SO 60 7 0 8 0 90 1 0 0 110 1 2 0 13*Dhbor <l/mn>
3-90 - -43.447 + 4.042 * ~&bor <i/mn); R-t - .a65
Km so3 Cl
<125fr 13 5.2 7.29
>125p 4.3 1.9 1.6
Ensemble 12.6 4.95 7.03
45op 3.6 4.4 2.3
>lSOp 3.1 0.8
Ensmble 5.3 4.2 2.1
Cl : 2.1 2.3 0.7
I
X
ENCIRELATION MG/M'.SO~ - % 02
1. General
Information is presented here against the background of equipment/processes encountered outside thecement industry, where acid gas abatement may already be practised - and where ideas for transferto our industry may originate. Our most frequent needs are to improve SC+ capture by calciumcompounds in raw mills and/or compensate for the absence of this absorption when mills are notrunning. Whilst there is a 50 to 75% reduction in SC& levels in a number of cement Works whenhydrated lime is suitably added, some sites need to understand why they record drops of only 20 to40% and there also is an interest in better understanding the possibilities for using of alkalinesorbents. This note aims to provide suitable background information as an aid to better understandingwhen the complications and costs of the “Untervaz Solution” may have to be accepted.
2. Sorbent Injection
2.1 Basic Description of Technology and Principal Variations
Sorbent injection is used primarily in pollution abatement as a means of reducing emissions of sulphurdioxide (SO-,> and other acid gases, such as HCI and HF. Material is usually injected into the gasstream as a fine powder, where it reacts with the acid gases, generating a dry product for collectionin dust arresment equipment. Dry injection methods are particularly suitable for small boiler andincinerator plant or retrofit applications where the capital expenditure for other systems is pro-hibitively expensive. The efficiency of S&- removal is 40 - 80%, depending on the sorbenc used(most commonly calcium and sodium compounds).
The sorbent can be injected at various points in the plant, according to the temperarure and conditionsat which it is most reactive. The most common systems for boiler plant are:
Furnace injection of calcium based compoundsHeat exchanger injection of hydrated (slaked) lime (Ca(OH),,Post furnace injection of Ca(OHk at relatively high humidityPost furnace injection of sodium based compounds.
In a cement process, we may see:
“Classic” SG- capture in the lower stages of the preheaterHydrated lime injection at top of preheater or in conditioning tower (probably as slurry)Return of calcined meal to cooler parts of system (preferabiy with moisture)Wafer injection at suitable points to increase possibility of reactions with raw feedHydrated lime addition to raw millInjection of alkali compounds or solutions to exhaust gas ductSG- capture by limestone in raw mill in the presence of moisture.
(Some different possibilities for injection are envisaged for Lepol systems.)
2.2 Principle of Operation
The reaction between sulphur dioxide and dry sorbent is a heterogeneous one . (Reactions with moistsorbents are discussed later in Section 3.2). SC& molecules diffuse through the gas stream and areadsorbed on to the sorbent surface before diffusing into internal pores where chemical reaction occurs.
These mechanisms are exemplified in the classical kiln/preheater sulphate cycles.
Dry calcium sorbents react with sulphur dioxide as follows:
The first stage is calcination:
CaC03 + CaO + CG-
Ca(OH)z + CaO + Hz0
(These reactions occur at temperatures greater than 760 and 570°C respectively. Dolomitic limestonestarts decomposition at a lower temperature.)
The second stage is sulphation:
CaO + SG_ + Y.Q + CaSO,
With excess oxygen, complete oxidation to sulphate occurs at temperatures ahove 800°C. Below thistemperature a mixture of sulphate, sulphite and sulphide is formed. (The optimum temperature rangefor direct reaction with hydrated lime is listed as 130 - 180 “C.)
Sodium compounds react with SO, as follows:
2NaHCO,-Na&O, + CG- + Hz0
Na&O, + sa* + ‘ha- -, lN&-so, + co,
Sodium bicarbonate decomposes to sodium carbonate, which then reacts with S%- to form sodiumsulphate. The these reactions are significant at temperatures above 130 - 180°C; at the lowertemperatures in this range the favoured SO, reaction is directly with the carbonate, but at highertemperatures the thermal decomposition and sulphation reactions occur simultaneously. It is thoughtthat the good performance of this sorbent may be explained by the fia that a shrinking core ofbicarbonate is continuously decomposed, providing moisture at a fresh reaction interface for S%-arriving through a permeable outer shell of sulphate A similar scheme is seen for potassium.
23 Selection and design considerations
Dry sorbent injection is usually one of the cheapest abatement options for SG- removal, particularlyfor small or retrofit plant. as the capital cost is low. The choice of sorbent is a prime considerationand depends very much on availability. Calcium compounds used for dry injection are primarilynaturally occurring limestone or dolomite or hydrated compounds derived from these raw materials.Reactivity is dependent on pre-treatment as well as natural properties. The sodium sorbents ofinterest are sodium bicarbonate (NaHCO,) and sodium sesquicarbonate (NaHCO,.Npl_C0,.2H,0).These occur naturally as nacholite and trona respectively. In making a choice, process economics arehighly dependent on delivered price of reagent and rate of use, despite the initial lower cost andcomparative simplicity of operation of the dry post-furnace injection processes.
There are three temperature windows for calcium sorbent injection in boiler and incinerator systems,which also broadly apply to cement kilns. (Note that there is a temperature zone where neither groupof reactions is very effective, especially in dry conditions.)
Calcium sorbents can be injected directly into the furnace, where at temperatures of 1100 -1250°C the calcination and sulphation reactions can occur,
Calcium hydroxide Ca(OHX_ will react with SO, at about 550°C and hence can be injectedbefore the heat exchanger.
At high levels of humidity calcium hydroxide will react with SO, at even lower temperatures(5 - 15°C above the saturation temperamre of the gas, as discussed in Section 3.2). watercan be injected with the calcium sorbent into the duct between the heat exchanger andparticulate abatement equipment or elsewhere
Sodium sorbents are also injected in boiler plant to the duct between the heat exchanger andparticulate abatement device, where the temperature is in or above the range 130 - 180°C.
It is possible to inject sorbents at several points in the plant and to combine this technology with otherabatement options. (No accounts of multiple injection systems are known for the cement industry).Handling problems may be encountered and not all sources of lime are equally effective in reacting(at a given fineness) in the time available at the point in the process where introduction is feasible.Reactivity increases as the surface area of the sorbent increases (particle size decreases), up to 40m3/gm. The calcium:suiphur ratio is generally set at 2, but can be as high as 6, particularly for lowsulphur coals where the mass of sorbent is still comparatively low.
The reaction efficiency for limestone ranges from 40 - 50% at calcium:sulphur ratios of 2 - 4.Dolomites give greater conversion efficiencies, and this is attributed to the more open structure of thesorbent material which enables greater diffusion of gas into the pores of the sorbent. Conversionefficiencies of 70 - 80% are achieved with sorbents of hydrated lime Ca(OH), at 8OO”C, and sodiumcompounds also yield conversion efficiencies of 70 - 80%. (Use of a fabric Nter for particulateabatement is claimed to enhance SO, abatement efficiency by ca. 10% because the sorbent collectedon the filter bags continues to react-with SO, during particle filtering. Dry sorbent injection to thefilter bags after a cleaning cycle, is claims as an altemativelsupplementary method to enhancereaction.)
Superstoichiometric quantities of reagent are usually needed because efficiency of reaction is low, andrecycle may also be required. Efficiency may even be insufficient for elimination of either very highor very low SC& concenrrations at a realistic stoichiometric ratio. Use of “conditioned” (ca. 10%moist) hydrated-lime has been claimed to give improvements due to (a) breakage of particles whenbrought into contact with hot gases (so generating more surface area) and (b) cooling, which increasesreaction efficiency. There are no known reports from the cement industry on this point, or onreactivity of different sources of limestone or dolomite.
Limestone is the cheapest sorbent material currently in use. Lime (calcium hydroxide) is about 5 -6 times more expensive than limestone and trona/nacholite are generally ten times more expensivethan limestone. Some studies suggest N&HC03 becomes still more efficient at higher temperatures(e.g., up to 815 deg C); it costs 2 to 4 times as much as hydrated lime. although consumption maybe lower and there may be less residue to dispose of. (There is little or nothing known about the use.of alkali compounds at relatively high temperatures in the cement industry.)
Combustion systems using high sulphur coals yield the most promising results where SO, levels are2000 - 4000 ppm. At SC& concentrations < 1000 ppm the reaction is diffusion limited and it maybe more difficult to achieve desired levels of efficiency. (In general, this technology is consideredto be less efficient than the “wet” methods described later.)
In boiler systems, the added sorbent and its interaction with the fly ash, can cause fouling of surfaces.Also, higher particulate loadings, decreased particle size and increased electrical resistiviry of theparticles can impair the performance of collection devices. Handling and disposal of larger quantitiesof solid waste with properties different from fly ash or conventional scrubber sludge can be difficultand increase costs. For example, sodium salts are soluble in water and hence disposal requirementsare more stringent.
3.1 Future Developments
Research is continuing to enhance knowledge of-the appropriate mechanisms acting in these injectionprocesses, with a view to developing alternative, moreeffective sorbents. For example, alkali metaladditives in limestone enhance SO, abatement efficiency and early indications are that lime-containingwaste materials, such as carbide mud and sugar mill mud, react faster and have a greater sorptioncapacity. The use of regenerable sorbents such as calcium silicates is another possibility.
3. Spray Dryers
3.1 Basic Description of Technology and Principal Variations
Spray drying is a standard chemical engineering operation used to produce dry powders of controlledparticle size, density and moisture content Spray dryers are used in pollution abatement for thecontrol of acidic species in a flue gas stream. Droplets of reagent are contacted with the flue gas ina reaction chamber - probably a modified conditioning tower in a cement Works. Liquid iscontinuously evaporating from the droplets in the chamber during the neutralisation reaction and thedry reaction product can be collected at the base of the chamber or in the dust abatement plant.
A complete system consists of the spray dryer (atomiser and reaction chamber), associated slurry/liquid handling equipment, a particulate collection devise and soiids recycling equipment. There arethree types of atomiser in general use: rotary, two fluid or spray nozzles The reaction chamber canbe a tower or dust, and the flow of the droplets and flue gas stream are usually co-current. Limeslurries are most often used, but sodium carbonate/bicarbonate solutions are also acceptable.
32 Principle of operation
a) Lime spray driers
The atomiser generates dropiets of lime slurry which are injected into the flue gas stream in thereaction chamber. In the capture of sulphur dioxide, the chemical reactions which occur involvewater and are believed to be:
Liquid phase: CaC03 + Sa- + %H,O -. CaS03.%Hz0 + Ca-
Gas/liquid phase: Ca(OH)l + .Sa- + Hz0 - CaSO,.‘/iHIO + lXH,O
Sa- is absorbed in the aqueous phase of freshly atomised droplets forming suiphurous acid,where the reaction of SO-, with lime or limestone proceeds rapidly, forming calcium sulphitewhich may later be oxidised and form gypsum in the presence of oxygen and water.
As the droplets pass through the chamber, water evaporates to yield a porous particle whichhas a dry surface but a wet interior. Sa- diffuses into the wet sore of the particle and thereaction continues.
The reaction of SO, with lime in the absence of any moisture is slow. Consequently, in orderto extend the reactivity of the lime in the unit, the temperature near the exit is maintained justabove the saturation point of the gas.
As mentioned earlier (Section 2.2), these reactions can be involved in sorbent injection in cooler partsof a cement production line, for example when Ca(OH)z is injected to the preheater or Sa- reactswith limestone in the raw mill. In the absence of water, however, the reaction rate will be very slow- for example at the top of a preheater tower. Water injection to the preheater at Santa Cruz (without
adding any extra lime) was reported to allow 10-20% reduction in SO, levels. Failure to comparehumidity levels and/or use fresh lime may account for several differences in experience of SG-capture in kiln systems.
b) Spray driers using sodium salts
Dry S&- reacts with sodium carbonate/bicarbonate from low temperatures: and hence the requirementto enhance the reactivity by stringent control of temperature and humidity is not necessary.
3.3 Selection and Design Considerations
The principal design parameters for spray dryers are droplet size and distribution, and inlet and outlettemperature. Multiple atomisers are used in order to achieve an even distribution of droplets in thereaction chamber, and the droplet size has to be such that the rate of evaporation is fast enough toprevent formation of scale in the reaction chamber as droplets/particles strike and stick to the walls,but slow enough to enable the reaction to occur. High inlet temperatures enable more water or limeto be injected, and low outlet temperatures (slightly above the saturation point of the gas) optimisethe abatement efficiency of the spray dryer.
Fine sprays and concentrated reagents have shorter drying and reaction times. Water evaporates fromconcentrated reagents rapidly and hence the neutralisation reaction occurs mainly between the acidgas and the porous particle. Fine droplets ( < 100 pm) are used with size tailored to the residencetime of the flue gas and droplets in the chamber or duct. The residence time in a chamber is usuallyin the range 5 - 10 secs, with droplet size < 100 pm. For injection of slurry into a duct, reactionand drying times of 1 - 2 secs are typical. Residence times and evaporative heat available in anexisting cement plant conditioning tower or gas duct system may limit the amount of SO, which canbe scrubbed.
The choice of sorbent will depend on its cost and availability: sodium salts give better “once through”efficiencies, but lime has a cost advantage over trone/nacholite and the calcium based reaaion productis insoluble in water which renders disposal easier, should this be necessary.
Spray dryers have been successfully used in Europe for controlling emissions of acid gases, primarilyfor combustion plant and incinerators, using a lime sorbent which is recycled to improve its utilisationand achieving abatement efftciencies of > 99% and > 90% for HCl and SG- respectively.Efficiency can be enhanced by increasing the stoichiomeuic ratio for specific conditions oftemperature and humidity, but the gains are limited by sorbent utiiisation, sorbent solubility and wastedisposal costs. The Ca:S stoichiometric ratio is typicaiIy in the range 1 - 1.5 and liquid:gas ratiosin the range 0.027 - 0.04 l/m3. Spray dryers offer several advantages over wet scrubbing, especiallythe fact that a dry product is formed which is easier to handle and dispose of than a liquid effluent.The capital cost, maintenance cost and energy requirements for the spray dryer system are lower thanfor wet scrubbing plant although reagent costs are higher.
The particulate collection device can influence the operating conditions of the spray dryer. Acid gasremoval can continue in a fabric filter but care has to be taken to prevent blinding of the bags.Electrostatic precipitators, however, can operate at temperatures nearer to the saturation point of thegas, hence the spray dryer outlet temperature can be lower which improves its abatement efficiency.The dry product from the spray dryer (hydrated &SO,) can be used for landfill, processed to yieldanhydrite or pelletised to yield synthetic aggregate.
3.4 Scrubbers
“Absorption” is a process which involves mass transfer between a soluble gas and a solvent in acontacting device; chemical reaction may or may not occur In process design, both the chemistryof the system and the physical structure of the equipment must be considered. Unfortunately, wateralone is not effective at removing SO, from a gas stream because (unlike HCI) it is not very soiubie:an alkaline solution is needed The driving force for gas removal is the difference between the partialpressure of the soluble gas in the mixture and the vapour pressure of the solute gas in the liquid filmin contact with the gas. Mass transfer occurs by molecular diffusion across the interface and the ratedetermining step can be in either the gas or the absorbent phase. When the gas is very soluble orreacts chemically with a reagent in the sorbent, the process is “gas phase controlled”
Trace gas removal systems can be categorised by the solubility of the gas and by the reactivity of thesystem. SO-, is classed as “moderately soluble” in water (I-IF and HCI are very soluble), and sodiumsulphite and-alkaline compounds are used with some success as additional reagents. Efficiencies ofSC& removal of some 99% are attained in appropriate circumstances. There are no known accountsof the use of sodium sulphite solution for SO-, capture in the cement industry: usage in power stationsgenerally appears to be associated with systems which treat the resultant chemical products toregenerate the solution of sulphite sorbent, or systems in which the sulphite is used alongside otherreagents, providing an initial capture of sulphur as an alkaline compound for subsquent displacementreaction to form a more readily disposeable or saleable by-product.
Gas absorbers which attain gas/liquid contact by bubbling dirty gas through a liquid are suitable forabsorption processes which are “liquid phase controlled and those which involve spraying liquidthrough the gas stream are suitable for processes which are “gas phase controlled”. As absorptionis a rate process, the concentration gradient (driving force for the reaction) and the (high) surface areaof contact between the liquid and gaseous phase are crucial design parameters. The surface area isdetermined by the packing material or droplet size and this is usually achieved using packing materialswhich are coated with liquid or by droplet/bubble formation. The absorber design also has to providea means for renewing the liquid absorbent so that a high driving force for mass transfer is maintained-
Gas and liquid flow rates and pressure drop across the absorber influence the driving force, theefficiency and in some cases the surface area (droplet formation). A good gas absorber designremoves as much pollutant as possible in as small a space as possible. The choice of equipmentdepends on the abatement efficiency required, the energy and reagent requirements and the propertiesof the dirty gas stream.
c. P. KERTON,Blue Circle Te&nicai Centre, Greenhithe,&lay 1994 (Updated, July 1994).
- I
r’
n
FLUE GAS BYPASS AROUND DRYERl-EMPERATURE I- - - - - - - - - - - - - 1
C O N T R O L I.~W A T E R
I
FLUE GAS~no:.i POlLEn J--J-
I
SPRAY DRYERWASTE RECYCLE
4-JFABRICFILTEHCATCH
RECYCLE
FEED PUMP
+ C L E A NFLUE GAS
TO ASIdDISPOSAL
BIN
r-BALL
cc: M I L L_STLAKER
a-l;.-,,
DETEN.TlONSLAKEFI
NOT SHOWN
APPENDIX 2
TEXT FROM INTERNATIONAL SYMPOSIUM ON GAS CLEANING
AT HIGH TEMPERATURES
Behaviour of Volatile Materials in
Cement Kiln Systems
GAS CLEANING ATH I G H TEMPERATURES
Edited by .
?qv
(‘l’trc: usit ccnIc11I iidilslry convcnliun is loltuwrtt iii cxprcssinfi I’ snlls o f riinny clicrnicnlatialyscs ill Icrrris of cIxitlcs. c.g.. CaO, S O , , hl,O,. clc., u s u a l l y 018 a ‘loss [ICC” bas is . i.e.,allcr allowing, fnr ihc Ins5 ill wciglrl cvcnlually crpcricflcut rluc l o tlcslruclion o f clrbonalcs.clc.. during Iml lrcnlillcnl.)
“\‘01,A~1‘11.1~~S5” ANI) hllXTIIANIShlS 01; VOI.A’1‘II,ISA-I’ION
‘1.11~ pritlcitd volnlil~ ~ICIIIC~IS arc K, N;I, Ct. S. I n Ihc cast of’ r a w nnlcrints, ccrlain sutrurcor~~t~~ur~d~ (rulfirtcs or ort:anics) c:ul rratlily clcco~~rt~sclvolnlilisc Indow Goo”C, bul IllOSlvdalitc co~ntmunds in raw inalcriids o n l y c v a p o r a l c pnrlially and a l higtlcr Icnitxralurcs as111~ reed pa5scs low;rrtls llrc k i l n hrrnilig xonc. ‘I’hc rcsitluc rcmins i n lhc producl. cilllcri n s o l i d ~cd~~iou ill IIIC plincitd phscs ol IIIC clinker o r as cliscrcic cocrqm~ncls. Whilstalnml all fcctl cllloritlr. w i l l cvatwmlc, lcs.scr aniounls 0r ollicr c o m p o u n d s do s o , wliilsl incorrlr:i’tl. liitd vcrlalilrs arc :ilii~o’;l ;ilw;iys ciilircly cvnpor;ilcd during cmiiIiIislion.
lfv;rtKrrarrd volarilc~ rravcl hack up 11rc kiln wilt, 111c comlm~lion eases and cordcrrsc a sirmrt;;rnic comt~ountl’; (lilrcr;rlirrg I:~lwl Iical):
i)
i i )
on llic Ucctl. li)rmitlg lhc his O r n rccirculaliiig inlcrnal votnlilc l o a d
n ;I lirrc rlrrsl r>r rcllrlc which is fin;llty Irappcd i n lhc g a s clrxning s y s l c m o rr a w m i l l arrtl hx~mcs p a r t or an cxlcrilal vnlalilc c y c t c . a s 111151 is parlly o rd$ly rl’lurncd ir1 tlrc sysic111
i i i ) 011 coltlcr strrl:rccs ill lhc syslcrii. linming llic Ixrsis O r hiltl~ups.
I’rcssurrs 10 cxploil cvcr more marginal rcscrvcs 0r r a w ni3lcrinls a n d fuels give rise l oirrcrcxirrg I;rmili;rrily willr llrc drm o f vohlilc spccics 011 process pcrlormarrcc. Wtrcricorrtlcrrsctt volalilcs rclurrr low;lrtls Ihc b u r n i n g zorrc, clctxriding o n Ihc overall clrcmicnlcr~nrliliorls and hrnint: ccrndiliorrs, llrry form a range or votalilc cnmpunds wlriclltlrcrr0clvcs cvapw;llc parli;rlly nri0 llrc cyctc only lids an utuilibriuni when ltx loiat quaillilyIcarirrt: llrc syslcm (itI clirrkcr ;md mm-rclirrrrcd tlusl) equals ltral cnlcrirrc lhc s y s l c m .
Alk;rlix ;md ~IIII~IICS ctrl~.rirrt! llrc trrrrrrirrp forrc irr trraclirc I:rrt:cly I’rlrrri :I \qr;lr;llc mr~llcr~5llll;llc t’ll;lr<, iiumiscilrlu wills Ilrc prLicip;rl fcrrilc Ilux. ‘Tlrc lrvct or volalilcs irrrccircul;rliorr i s sit;rrilic;mlly grcalzr ll1911 lhcir lol;d ralc or irrlroducliori am1 lhc s~rbsln~~ccsit1 llrc vapour ptrasc’ cnri 115 irr v;rrious slalcs or dissoci:llion a n d recomlrinalion. III gcncml,Itrc prc lcrrd clrloritlc corrrt~rmnd i s txrl:rsrium cllloritlc and only wlicrr lhcrc i s an cxccss IIIclrloriric lor cOcmic;rt crmrlrimrliori will) pol;lssium w i l l sodium ctrtoritlc lx hrmcd as : I
rccircutalirrg vohlitc strxics. Alk;tli sulhlcs (Na2S0.,. K,SO,t cvatxxatc cony,rucnlly,tlisnprxzlring c n l i r c l y wticri Ilr;rlctl Ihr a loiig period. Cn.S04 ttcconiposcs arid hvcs rcsidu:dCnO (ill, trxitlising contlilior~st. s o lh:il CaO:CnS04 niclls c a n rorcll. T y p i c a l rccirculalirrgvrhtilr lrds rxtlrcssctl a3 XI ul’ llrc 1~1lal quimlily inlrotluccd a r c a s roilOws:
% 1.(‘lrlrrridr(s) XXKt Na20 IS0 - 200
K-0 XX) . rLv1 SOJ 2uo . R(X)
Ic!“u
.utr,r
= 0
‘??
V
‘;oJluo-J
‘Jle~“su[ /S?(?J(U! I!2 Jl2U
y43‘U
O!lJJ(d
S/U
%!S
Jp
SS
JJOJd
‘UO
!lZO
[2S/U
~!S
J,, S
SJJO
Jd
‘JA
oq
e
sv
‘XllU
‘p
J!
- (O
pl
![e~
[e/J1zjpi)
.illS!U
fJ~
J PJSJ
m2J J
O U
O!U
J[JS
*(se3 ‘p!nbg
‘pg
os)
[X
I! JO
JJ!O
~~
‘ssauau
y
J~O~/(ZO
-J
~s3!lsp
lJeJzq3
[xl,’
‘S%U!llJS Xl2~/JJU
Jfl~
‘(OyJ gz~pzpl2#ls)
.~JlS!UJJqJ
pJJJ
M2J
JO
UO
!lJJ[J’j
3J!lS!JX
JUeq
J
[XI-J
‘So’U!llJS
JJUlq/JU
l2[~
%J!U
Jflq
pJ[[O
JlUO
3+~JX![ZJJU
+I iy S:X~U p
g
tun
q 1~0s
SNO
il3V
?OtIlN
03 TiBlSSOd
UJn
,Ji ;S
”a
r!leqle m
z;q;rJd JO
UO~I!SO~UJO~uo+?l2do
u:1s3p::JU
!J[ZJJld
:uto
?o
[
ra3ipq
os
.iJlJtJJOJa’
-
luy
dn-p[!nq-!wz
.
SxZJ[U!
:!O
/SOJ:Z
p[OJ
-(lJ2qS
) [O
JilJJ.\
-U&SJp
W
JlS.\S
IJI2JqJJd
(.SO
u
SZ%)
.(JUJ!JlJJJ
[tU
LlJ
ql
(*(l!su
ap
)
IU71UOJ
xrll-i
lJ
!f!q~
hp
3d
JZ!S
JJqlx[-~
JnC
d2.\
JJiZ.I\
:‘J!Jt-ipJl
.i([?-‘O
( -
&J!JtTpJJ
s+
?q
O@
-
JJJqd
SO
ulz
7u
oz
d
U!u
ng
au02
a.l!L
un
q
u! uo!ysodtuoJ ![i?([v
JUOZ
%!+fnq
;o J[i_rofd .dwaL
SUO
!l?!L?.\ -
[JQ
[ -(SJJnSSJJd
Jl-dZs\).dm
in :uoz &J~HI~
Ic!“u.utr,r = 0‘??V
‘;oJluo-J
‘Jle~“su[ /S?(?J(U! I!2 Jl2Uy43‘UO!lJJ(dS/U%!SJp SSJJOJd
‘UO!lZO[2S/U~!SJ,, SSJJOJd
‘JAoqe sv
‘XllU ‘pJ! - (Opl ![e~[e/J1zjpi).illS!UfJ~J PJSJ m2J JO UO!UJ[JS
*(se3 ‘p!nbg ‘pgos) [XI! JO JJ!O~~‘ssauauy J~O~/(ZO-J
~s3!lsplJeJzq3 [xl,’‘S%U!llJS Xl2~/JJUJfl~
‘(OyJ gz~pzpl2#ls).~JlS!UJJqJ pJJJ M2J JO UO!lJJ[J’j
3J!lS!JXJUeqJ [XI-J
‘So’U!llJS JJUlq/JUl2[~
%J!UJflq pJ[[OJlUO3+~JX![ZJJU+I iy S:X~U pg tunq 1~0s
SNOil3V?OtIlN03 TiBlSSOd
UJn,Ji ;S”a
r!leqle mz;q;rJd JO UO~I!SO~UJO~uo+?l2do
u:1s3p::JU!J[ZJJld
:uto?o[ ra3ipqos.iJlJtJJOJa’ -
luy dn-p[!nq-!wz .SxZJ[U! :!O/SOJ:Z p[OJ-
(lJ2qS) [OJilJJ.\ -U&SJp WJlS.\S IJI2JqJJd
(.SOu SZ%) .(JUJ!JlJJJ [tULlJql
(*(l!suap) IU71UOJ xrll-i lJ!f!q~
hp3d JZ!S JJqlx[-~
JnCd2.\ JJiZ.I\:‘J!Jt-ipJl .i([?-‘O( -
&J!JtTpJJ s+?qO@ -JJJqdSOulz 7uoz dU!ung
au02 a.l!Lunq
u! uo!ysodtuoJ ![i?([v
JUOZ %!+fnq ;o J[i_rofd .dwaLSUO!l?!L?.\ -
[JQ[ -(SJJnSSJJd Jl-dZs\).dmin :uoz &J~HI~
~cmpcraturc in a WCI prnccsr k i ln , a considcrablc dab-bank c l I t.-6urcrncnls 1115 been buillup. The USC o f lnwrr a s h rucl lowcrcd c l i n k e r K,O l c v c l b y O.lS%. dcspilc 111~ inIroduclior1of n IiIIlc mnrc p&ssium IO lhc system (an cxlra 0 . I 16 o n clinker). T h e dusl - rclurncd IOlhc kiln - had bccomc more rich in alkalis, so lhal Ihe proportion or K,O broughl in by solidfuel fell lrom 24% I O IX% while ihai brough1 i n b y dust rcIIIrn rose from 18% I O 29%.This s~rp.gcs~s 1ha1 KzO incotporaIion in clinker no1 only dcpcnds on 1hc quan1ily inlroduccd11u1 also . a n d almvc all clsc _ o n IIIC type of malcrinl w h i c h b r i n g s i1 i n a n d perhaps o n 111~pnsiIimr whcrc i1 is injccIctl. On screening 111~ clinker al 20 mm. chcmic~l analysis showeda K,O coriccnlralinr~ snmc IO% Irighcr i n Ihc cn;~rsc f r a c t i o n . The clinker a lka l i COIIICIII hass~~cccssli~lly been rctlucccl i n lrials b y c a l c i u m chloride atldilinri nl l h c Ilamc.
Cnsc 6: A hil:h chlnridc coal ( - 0. I5 % Cl) can only bc ~isctl as a mix will1 anolhcr coal loavoid Imild-ullc wilh Iyliically 2 % Cl a1 Ihc ImI1nm Or cyclone 4 (lhc lowcsl in lhc prchcalcr~nwcr). hn;rlyTis of Inriltl~ul~s along IIIC kiln indica1ul chlnridc lc,vclr up IO 30% (al zero lossnn ignirinn) in 111~ coaIing Iron1 lhc base of cyclone 2 and 20% a1 SO 111 inlo Ihc kiln (tlcspilciit hs’i ih:m 5 % lrvcl i n Imllr lmi :md rold p;nI’i 0r Ilic k i l n ) .
C:1w 7: Atldinl; a sccontl ln~~hc;l~cr c y c l n n c s~agc IO a l o n g d r y process k i ln (a varinrIt of1hc I:igutc I prnccss, will1 a higher k i l n IcngIh/dian~cIcr ralio a n d a single cyclone slagcnhnvc i1) yicldcd vnrimrs build-up problems. To resnlvc ~hcsc, IIIC kiln gas cxi1 0, lcvcl wasiricrcA5rccl rrorll 0.5 In I .5 %, solid rd rcsiduc al 90 microns was rcduccd lo below 25 % andscvcral cmr~l~r~ss~d air “blaslcrs” wcrc inslallctl lo dislodge malcrial rrom lhe lower regionsoC 111~ prchcnlcr. T h c s c acrions improved IIIC siIuaIior1 and sul~scqI~cnIly addiIional mcasurcswcrc Iakcn: rcl~/l;iory slirrcrs wcrc addul l o I h c l i n i n g near the k i l n b a c k end, hurncr a i rvcltXiIy was incrcawd. a n d a “non-slick” lining was inslallcd in 1hc kiln cxi1 gas duel andcycl011c dip-lubes. ‘I’hcsc Crrm mntlc bcllcr ouIliu1 ralcs pnssihlc wilhoul b u i l d - u p s .
IIc~cnIly. a Iiil;hcr snll’ur rd hlcntl 113s been nscd, :~ccomp;mictl b y s l a g (S - I X) :Imonglhc r;~w niix coml~~ncnIs. I’rchcaIcr blockage problems rccurrcd, bu1 b u i l d - u p s c;m beavoidctl if the SO, l c v c l i n snmplcs taken Irnm the k i l n cnlry m a l c r i a l i s kcp1 b e l o w 2.5%b y lirnilirig lucl S conlcnl and sl;ig use i n lhc r a w m i x , provided lhal i n addilion l h c oxygenlcvcl at IIIC kiln back cm1 is kcp~ consis~cn~ly a1 or above 2%. Cnmpui~r c0nir01 or ihc ki lnIiclpr I n achicvc succc’i’i. rctlucinl: lhc vari:rhilily ol l h c 0, s i g n a l .
cxw Ii: I ;~li~n:ih~ry tl:11:1 on minor clcnic111s conlirm clvccls crlrxcrvr.tl ill ln:tclicc. I:rlrcr;~n~plc, suITur vnl;rIiliIy i n ;I s~;~rrtlarrI rcginrc (70% N,, 30% CO) is close I O 100% a1 0%0, OUI I~lls in ihc prcscncc Or 0,; r~~~~rihclcss ihc CrrCd Or 0, is much ICSS al 1400°C lhana l I2W”C. The volalilily 0r m i n o r c l c m c n l s i n l h c laboralory i s a l s o m u c h grcalcr r0rpowdcrrtl m a l c r i a l lhan rOr grarIulcs.
CXSC 1 2 : S O , 11~s l~ccn tmmit~rcd ;II lhc kilt1 Iwck cd IO dclcrwiw hrc:~l rules for avoitlinl:hltKk:igc Icndcncics. ‘I’hc S O , sil:n:rl i s ncpisy :~nd dillicull l o inlcrltrcl willroul a krtowlAl:cor IhC hiSlWy Or IllC SySlCltl. C.G.. a rcccn~ brcak;rway of sulfalc b u i l d - u p m a l c r i a l a r r i v i n gi n IIIC lmrning ~nnc c a n give a h i g h S O , s i g n a l a1 111~ k i l n back end dcspilc tlrc prc~cncc ola good flnnrc a n d ~cccl~~;~blc lcvcls of vnl;llilcs i n k i l n cnlry malcrial. I<ulcs l1avc lowcrccl111~ nun~l>cr (,I k i l n >I,,,,F ,w, yc:,r c;mcctl try I~ruln.:~tcr Irlcsk:rl;c 1’reun r~vc’r ‘)I) II) Icv\ 01:rnill. 1~151 lirlrc ln~~rrs Il:rvinI: :II\~I I:rllr~n loom :~r~nmtl 4,511 Jk‘r yc:tr 111 :rlr~url IIIII. ( ‘ I hi.11. lvcrt’:rl\o m:ijfn l::rin’; i n \I*rlt\ 1311wtl Ily rinl:\ :III~I Irr~3L;tw:1y\ ;II lhc kiln t’rllry rr.:ll.)
l3TECl~S OF C O N D E N S A T I O N
Cast Y: A prccalcincr kiln ran well will1 a Cl lcvcl in kiln cnlry maIcrial of 3 IO 4% (aboui The clrcc1 w h i c h rccirculaling vcd;IIilcs cxcrt o n b u i l d - u p rnrm:rIion a~ 111~ k i ln (gas) cxi10 . 5 % less 1har1 111~ K,O Icvcl) provided n o I r a c c of C O w a s indicald. (‘l’hcrc w a s aboul dcl~ntls ori coniposilion (governing Icmpccr;ilnrc or liquid lirrm;rIion :mcl Ihus lhc posilion andI . I % S O , i n I h c k i l n cnIry mc;ll i n Ihis siIuaIior1.) IC CO was tlc~cc~cd, Ihcrc was abnu1 2% h;trclncss or Iiiriltl~ul1s as well as Ilic surRcc Icnsirm and viscnsily Or Ihc liquid condc~is:ilc)S O , and SX K,O i n IIIC 1101 k i l n inlc1 l&cl. accompaniul hy b u i l d - u p s based o n SpurriIc a n d o n 1hc quanlily ( w h i c h gnvcrns ralc O r CurmaIion). ‘I’hc p l a n 1 p$omclry and IllC(2Caz(Si0,).CaC0,) and c u b i c K C I cryslals. ( I I i s gcncrally rccogniscd lhal regular k i l n ll~rougl~pul a l s o play a par1 i n m a k i n g clrccls mnrc or less prnnounccd. I n cxlrcmc cases.opcralion helps IO minimisc Ihc phcnonicnon 0r ccmcnlaliori by Ihc Crcczingl Ihawing Or par1 of 111~ k i l n P,aSCS ;ITC ‘bird” O F ‘by-passed’ Cnr qrrcnching a n d scparalc dc-tluslirr~ l ocliloridc-linsul tlclx,siIs.) rcmnvc volnlilcs . i n c u r r i n g linancial pcnallics i n plan1 cosl, complcxily a n d r0Ci use.
Cnsr In: T o c x n m i n c IIIC rcnsibiliry oC p r o d u c i n g a sulraic-rich clinker wiIhou1 insInlling a I n lhc pasl. s c v c r a l empirical limils have been l~roposcd rOr conccnlralions d volnlilcs
b y - p a s s . ICSIS WL 1m1 Inr some weeks will1 I h c objccIivc or reducing b u r n i n g roncvolaIili.~~tinn b y p l a y i n g o n process paramcIcrs a n d prnducing a IighIly mincraliscd clinkerwill1 higher volalilc rclcnlion. D u r i n g changcovcr ~hcrc was some I c n d c n c y l o rnrrn sol1build-ups in Ihc prchca~cr, bu1 wiIh ihc new regime csIablishcd ihcsc movctl lowards lhc kilnfcul chu~c wiIhou1 c a u s i n g m a j o r problems for k i l n opcniion. (EvidcnIly lhcrc a r cphcrIon1cna of boll1 shorI-Icrm a n d l o n g - I c r m sIabiliIy: o n c e a slablc b u r n i n g zonevolaIili.saIion is csIablishcd, in lakes Iimc f o r sIablc condiIions I O arrive higher u p the syslcmand in Ihc Iargc masses or malcrial in lhc build-ups and coalings already in cxislcncc.) Theapparcn1 b u r n i n g ~nnc IcmpcraIurc w a s rcducul b y almu~ 1 2 0 ° C . while K,O volalililydroplwl IrIlm 70% III 60% i n 111~ b u r n i n g ~onc a n d IhaI ol S O , Iron1 RO% Iowartls lhc ranl:cSO% I O GO%, provitlcd lhnl k i l n cxi1 oxygen l c v c l w a s kcp1 a b o v e 2 % . Thcrc wcrcin~provcn~cnIs in kiln outpul raIc and rucl consumpIion and lhc cxpcrimcnlal Works adoplcdccrlain Or Ihcsc changes during normal nl~ralinn rOr scvcral years.
C n s c I I : TCSIS wcrc c;Irricd 0111 invnlving variotrs N O , lcvcls ( t o indicalc llamcIcmpcralrIrc) a s well as chcmic~lly rcrhlcing rh0C contliliruIs.
so, : ‘I’hc r a l i o or S O , i n Slngc I V I n S O , i n r a w iri~l variedIypically Iron1 I.R IO 2.7 lnr 111~ higher lcvcls ol NO., and was3 . 0 [or a IOW 0, Icvcl. The clinker S O , c~nlcnl fell.
K,O a n d Na,O : In a parallel manner. for K,O 1hc ralin of l h c c o n l c n l i n S~ap,cI V IO Iha i n r a w meal varictl from 3.X IO 4 . 4 a n d rnr NazOrrom I .6 IO 2.0.
In gcncral, rultrcing cnndiIions incrcascd SO, lcvcl a1 Slagc IV by a hClOr 0r 2, also givinga lower clinker SO,.
~cmpcraturc in a WCI prnccsr k i ln , a considcrablc dab-bank c l I t.-6urcrncnls 1115 been buillup. The USC o f lnwrr a s h rucl lowcrcd c l i n k e r K,O l c v c l b y O.lS%. dcspilc 111~ inIroduclior1of n IiIIlc mnrc p&ssium IO lhc system (an cxlra 0 . I 16 o n clinker). T h e dusl - rclurncd IOlhc kiln - had bccomc more rich in alkalis, so lhal Ihe proportion or K,O broughl in by solidfuel fell lrom 24% I O IX% while ihai brough1 i n b y dust rcIIIrn rose from 18% I O 29%.This s~rp.gcs~s 1ha1 KzO incotporaIion in clinker no1 only dcpcnds on 1hc quan1ily inlroduccd11u1 also . a n d almvc all clsc _ o n IIIC type of malcrinl w h i c h b r i n g s i1 i n a n d perhaps o n 111~pnsiIimr whcrc i1 is injccIctl. On screening 111~ clinker al 20 mm. chcmic~l analysis showeda K,O coriccnlralinr~ snmc IO% Irighcr i n Ihc cn;~rsc f r a c t i o n . The clinker a lka l i COIIICIII hass~~cccssli~lly been rctlucccl i n lrials b y c a l c i u m chloride atldilinri nl l h c Ilamc.
Cnsc 6: A hil:h chlnridc coal ( - 0. I5 % Cl) can only bc ~isctl as a mix will1 anolhcr coal loavoid Imild-ullc wilh Iyliically 2 % Cl a1 Ihc ImI1nm Or cyclone 4 (lhc lowcsl in lhc prchcalcr~nwcr). hn;rlyTis of Inriltl~ul~s along IIIC kiln indica1ul chlnridc lc,vclr up IO 30% (al zero lossnn ignirinn) in 111~ coaIing Iron1 lhc base of cyclone 2 and 20% a1 SO 111 inlo Ihc kiln (tlcspilciit hs’i ih:m 5 % lrvcl i n Imllr lmi :md rold p;nI’i 0r Ilic k i l n ) .
C:1w 7: Atldinl; a sccontl ln~~hc;l~cr c y c l n n c s~agc IO a l o n g d r y process k i ln (a varinrIt of1hc I:igutc I prnccss, will1 a higher k i l n IcngIh/dian~cIcr ralio a n d a single cyclone slagcnhnvc i1) yicldcd vnrimrs build-up problems. To resnlvc ~hcsc, IIIC kiln gas cxi1 0, lcvcl wasiricrcA5rccl rrorll 0.5 In I .5 %, solid rd rcsiduc al 90 microns was rcduccd lo below 25 % andscvcral cmr~l~r~ss~d air “blaslcrs” wcrc inslallctl lo dislodge malcrial rrom lhe lower regionsoC 111~ prchcnlcr. T h c s c acrions improved IIIC siIuaIior1 and sul~scqI~cnIly addiIional mcasurcswcrc Iakcn: rcl~/l;iory slirrcrs wcrc addul l o I h c l i n i n g near the k i l n b a c k end, hurncr a i rvcltXiIy was incrcawd. a n d a “non-slick” lining was inslallcd in 1hc kiln cxi1 gas duel andcycl011c dip-lubes. ‘I’hcsc Crrm mntlc bcllcr ouIliu1 ralcs pnssihlc wilhoul b u i l d - u p s .
IIc~cnIly. a Iiil;hcr snll’ur rd hlcntl 113s been nscd, :~ccomp;mictl b y s l a g (S - I X) :Imonglhc r;~w niix coml~~ncnIs. I’rchcaIcr blockage problems rccurrcd, bu1 b u i l d - u p s c;m beavoidctl if the SO, l c v c l i n snmplcs taken Irnm the k i l n cnlry m a l c r i a l i s kcp1 b e l o w 2.5%b y lirnilirig lucl S conlcnl and sl;ig use i n lhc r a w m i x , provided lhal i n addilion l h c oxygenlcvcl at IIIC kiln back cm1 is kcp~ consis~cn~ly a1 or above 2%. Cnmpui~r c0nir01 or ihc ki lnIiclpr I n achicvc succc’i’i. rctlucinl: lhc vari:rhilily ol l h c 0, s i g n a l .
cxw Ii: I ;~li~n:ih~ry tl:11:1 on minor clcnic111s conlirm clvccls crlrxcrvr.tl ill ln:tclicc. I:rlrcr;~n~plc, suITur vnl;rIiliIy i n ;I s~;~rrtlarrI rcginrc (70% N,, 30% CO) is close I O 100% a1 0%0, OUI I~lls in ihc prcscncc Or 0,; r~~~~rihclcss ihc CrrCd Or 0, is much ICSS al 1400°C lhana l I2W”C. The volalilily 0r m i n o r c l c m c n l s i n l h c laboralory i s a l s o m u c h grcalcr r0rpowdcrrtl m a l c r i a l lhan rOr grarIulcs.
CXSC 1 2 : S O , 11~s l~ccn tmmit~rcd ;II lhc kilt1 Iwck cd IO dclcrwiw hrc:~l rules for avoitlinl:hltKk:igc Icndcncics. ‘I’hc S O , sil:n:rl i s ncpisy :~nd dillicull l o inlcrltrcl willroul a krtowlAl:cor IhC hiSlWy Or IllC SySlCltl. C.G.. a rcccn~ brcak;rway of sulfalc b u i l d - u p m a l c r i a l a r r i v i n gi n IIIC lmrning ~nnc c a n give a h i g h S O , s i g n a l a1 111~ k i l n back end dcspilc tlrc prc~cncc ola good flnnrc a n d ~cccl~~;~blc lcvcls of vnl;llilcs i n k i l n cnlry malcrial. I<ulcs l1avc lowcrccl111~ nun~l>cr (,I k i l n >I,,,,F ,w, yc:,r c;mcctl try I~ruln.:~tcr Irlcsk:rl;c 1’reun r~vc’r ‘)I) II) Icv\ 01:rnill. 1~151 lirlrc ln~~rrs Il:rvinI: :II\~I I:rllr~n loom :~r~nmtl 4,511 Jk‘r yc:tr 111 :rlr~url IIIII. ( ‘ I hi.11. lvcrt’:rl\o m:ijfn l::rin’; i n \I*rlt\ 1311wtl Ily rinl:\ :III~I Irr~3L;tw:1y\ ;II lhc kiln t’rllry rr.:ll.)
l3TECl~S OF C O N D E N S A T I O N
Cast Y: A prccalcincr kiln ran well will1 a Cl lcvcl in kiln cnlry maIcrial of 3 IO 4% (aboui The clrcc1 w h i c h rccirculaling vcd;IIilcs cxcrt o n b u i l d - u p rnrm:rIion a~ 111~ k i ln (gas) cxi10 . 5 % less 1har1 111~ K,O Icvcl) provided n o I r a c c of C O w a s indicald. (‘l’hcrc w a s aboul dcl~ntls ori coniposilion (governing Icmpccr;ilnrc or liquid lirrm;rIion :mcl Ihus lhc posilion andI . I % S O , i n I h c k i l n cnIry mc;ll i n Ihis siIuaIior1.) IC CO was tlc~cc~cd, Ihcrc was abnu1 2% h;trclncss or Iiiriltl~ul1s as well as Ilic surRcc Icnsirm and viscnsily Or Ihc liquid condc~is:ilc)S O , and SX K,O i n IIIC 1101 k i l n inlc1 l&cl. accompaniul hy b u i l d - u p s based o n SpurriIc a n d o n 1hc quanlily ( w h i c h gnvcrns ralc O r CurmaIion). ‘I’hc p l a n 1 p$omclry and IllC(2Caz(Si0,).CaC0,) and c u b i c K C I cryslals. ( I I i s gcncrally rccogniscd lhal regular k i l n ll~rougl~pul a l s o play a par1 i n m a k i n g clrccls mnrc or less prnnounccd. I n cxlrcmc cases.opcralion helps IO minimisc Ihc phcnonicnon 0r ccmcnlaliori by Ihc Crcczingl Ihawing Or par1 of 111~ k i l n P,aSCS ;ITC ‘bird” O F ‘by-passed’ Cnr qrrcnching a n d scparalc dc-tluslirr~ l ocliloridc-linsul tlclx,siIs.) rcmnvc volnlilcs . i n c u r r i n g linancial pcnallics i n plan1 cosl, complcxily a n d r0Ci use.
Cnsr In: T o c x n m i n c IIIC rcnsibiliry oC p r o d u c i n g a sulraic-rich clinker wiIhou1 insInlling a I n lhc pasl. s c v c r a l empirical limils have been l~roposcd rOr conccnlralions d volnlilcs
b y - p a s s . ICSIS WL 1m1 Inr some weeks will1 I h c objccIivc or reducing b u r n i n g roncvolaIili.~~tinn b y p l a y i n g o n process paramcIcrs a n d prnducing a IighIly mincraliscd clinkerwill1 higher volalilc rclcnlion. D u r i n g changcovcr ~hcrc was some I c n d c n c y l o rnrrn sol1build-ups in Ihc prchca~cr, bu1 wiIh ihc new regime csIablishcd ihcsc movctl lowards lhc kilnfcul chu~c wiIhou1 c a u s i n g m a j o r problems for k i l n opcniion. (EvidcnIly lhcrc a r cphcrIon1cna of boll1 shorI-Icrm a n d l o n g - I c r m sIabiliIy: o n c e a slablc b u r n i n g zonevolaIili.saIion is csIablishcd, in lakes Iimc f o r sIablc condiIions I O arrive higher u p the syslcmand in Ihc Iargc masses or malcrial in lhc build-ups and coalings already in cxislcncc.) Theapparcn1 b u r n i n g ~nnc IcmpcraIurc w a s rcducul b y almu~ 1 2 0 ° C . while K,O volalililydroplwl IrIlm 70% III 60% i n 111~ b u r n i n g ~onc a n d IhaI ol S O , Iron1 RO% Iowartls lhc ranl:cSO% I O GO%, provitlcd lhnl k i l n cxi1 oxygen l c v c l w a s kcp1 a b o v e 2 % . Thcrc wcrcin~provcn~cnIs in kiln outpul raIc and rucl consumpIion and lhc cxpcrimcnlal Works adoplcdccrlain Or Ihcsc changes during normal nl~ralinn rOr scvcral years.
C n s c I I : TCSIS wcrc c;Irricd 0111 invnlving variotrs N O , lcvcls ( t o indicalc llamcIcmpcralrIrc) a s well as chcmic~lly rcrhlcing rh0C contliliruIs.
so, : ‘I’hc r a l i o or S O , i n Slngc I V I n S O , i n r a w iri~l variedIypically Iron1 I.R IO 2.7 lnr 111~ higher lcvcls ol NO., and was3 . 0 [or a IOW 0, Icvcl. The clinker S O , c~nlcnl fell.
K,O a n d Na,O : In a parallel manner. for K,O 1hc ralin of l h c c o n l c n l i n S~ap,cI V IO Iha i n r a w meal varictl from 3.X IO 4 . 4 a n d rnr NazOrrom I .6 IO 2.0.
In gcncral, rultrcing cnndiIions incrcascd SO, lcvcl a1 Slagc IV by a hClOr 0r 2, also givinga lower clinker SO,.
.“c]
%:,q
v%3
!:J’(~
OS)
%3)
Z’r,>
r
::,‘(“
oS
)‘ry?
(
!alq
w~~
,,~:(
'pos
)'y!
<$
~I!lI.
,3IIX~
:('O
>r3'
('0!
S)'V
~~)
>\!JJl
ltk
DJF.
~~,'hl
lC~:,
:SNl
~l~~
S ll,
l?,
IIIOJ)
pW
d>\\
,>J
,"!J~l
l!\\l
\I,
,Xl,J!
],,3,~
! J
JI! S
pWlO
dlll
~~ W
,',l
llO2
Ja\I
lO p
ill! '
!lI.I,
'SI~Ul
lOJ3
J!ll
H!llr(
pWlJal
,l 1
," p
?I.,
X,Y?
,"I,
i! -
"OS*
>('"
OSIQ
Z
- a,
!u!r
tq%a
, rr
myr3
sC
t~o~
wslr
~pi~
o~ wJ!p '9
.2 '
~JU~
JOJ sp
ltn~
1111
0~p,,
l!
p?l,S!
,qC,S;
, 7
q hl!
\ll l
!!Jq!,
!ll,,a
Mal
l pi
ll!
St,O
Jp ~
JW!J
X,ll
lJI ,
CllJ~l
ll! '
SWaJ
Jll!
S3ll
!Il!O.
,
JO S
S;rU~~
!l,l
?I,1
SV
'StIrI
-pl!nq
arr
!l!lr!
- s
m!~l
rls I
10 s
l!scxl
.,p l
Il!rn
Sl! _ ,
wC U
fl!Sal
[pC x
ne.2
~,,'!1
',,c,
UK
,
,fXIl
!Sl
1O!IX!
~J
,,!"!"
'~\I~
aY
,OAO
Jd UC
J pX
tJ
>,,I
110 Sl
!S"h
~
'(Z aJ
n3!:
,) De
w,*
,,,"
,a',
,,JAa
S,(1
,11 p!ll
,\!I
JO
\,"!,l
!t\,JO
J 3
\l!?.W
,It!
'aJl
ll~J;l
t,lll;
ll <
!\I1 II!
,'!
'h,
Sl1O!l
!SW,l\
10.7
~,CJ
,I,~
,"
93llCJ
alI1
SaW
JXl!
l,+
,M ,
3)(
JO llO
!I!ppC
II! I
,l!A\
',l!
!JW!ll
l 1
5,ll!
"I!'
( I
I! aSl
!i,d
?lCJ
,llF
ll[I
JO l
lO!I!S
OdlllO
., a
l,) W
C,ll
J,El
01
3ll!lS
2Jalll
! I
KllJO
S!
I, '(,
L(j,
'lll
lt!lll
~,!~,)
a&f
)8 b
\O,"
q S
lJl!ls
'OSl
!3 po!yy
/r
OS'"
N Il
lJlS
h XJ
IWJ~
\ 30
1 II! Il
l!l,
JW'~~
ltTJ,n
s
!,l?~,
I!
p!lllJ
!, se
X,,
C!l!ll
!
h,q'!'
,flJd
ISO
III "&,m,,
- m(
j 18
UCJ
Sl,l
II! JS
W,J1
10.7
S;lil!
J,flS
lSO
,A,
'(X,Jn
lS
2110
II! &O
R,,
l.32
)
,calii
MC
J p2
11!2
,w X,
IIWJ
J Xq
'0
s JO
3~11
idm J
OJ
;IJ~\I
CJXIII
I~I
urn11
1y10
uv
s! 2~3
11.1.
'S;lll
!.Y[lS
Sll
(llJCA
J"
llll!I
l!lllJ
l!( X,
l 3ll
!,l!l!
. .
'Slll~
Il,'lJ
l,
thl-,l
,l\lq
Wt!A
l!J3~l
!
UPJ
\IO!iC
Jl\tJJ
lJO3
% ,
pUll
OJC
OI
atl!JO
il,I
JO
\lO
!lC[ll
\llllJ
X!
"II<,.
',,%?l
S JW
!?l,
"J', Ul
OllO
q
a\,\ S,
TJCM
OI
13i\p
JX
!J
alI1 JO
?Il
ll,Zl
p"
aJ
ll,!?f
a\I
l
\I!
t,',l,
aA?p
W!
J S&
l-,l
,!no '(
~J\l
lCJX
,\Wl
Jam0
1 k,
,$h,
s
e iv ap
!Jo,
c,n
tmpo
s) 3.
006 pm ~8 unmmq sa
sl\a
p\io
3 au
o,v
?~!Jo,
I,~lur
i!sral
o,,
~~ro
!~e~rn
lc~a
\lr!q
l
uo!les
~r;lpi
ro:,
SU!
IIJ;~A
~~
e11~
~10tt
~r~d
m ~
J~III:
J~I!~
ssa,
r!
3JabI.
I.
(TWX
lJd
Al,
' X
,, J
" s;l
lll\,3
kl Z
?:~\!l
~.!l,W
ll 3
11, I
,! \\1
!,,,
,31!,\
1!~.)
,N,"
F/S!!?
alttu!
1u!
ssa,
I,I!M
'p
aXo,
d111
7
s\JJa,
sXs
Qu!ilf
a\I-2J
d
J~,tli
u!s
3\,1
c1;ln!
3
'JT~~I
XIJ~
s!
u,!y XW
,OJ
71,l
\!lOJJ
X,\
!X3 t
l,!lt!
,OA J
O ,W"
l,!,a~
!, 3
11, l
,~llfl
l,l,"
_ W,.h
,'!\
"S,\l!
JO
SJ!l!,
!C,!SS
Od S
!! ,
,,7"\
Sk'
\1111,
1J
,Stlp
JO Sa
,Jh
,,!llJ
2,11
a&L
!,,
"Sa,,.
,.
'kJ,\.
!\llaS
'l?
M-!\ll
;ls ',
3M
- llO
!~,ZJC
d~lt,
,W
,
II,!?
JO
SJall\
1l!ll1
I\la
J7JJ!p
JA[
OAII
! lIJ
!I,M
SSa
2OJd
ll,!
J 1
117111
.75 a
\(lJ
O S,i
,l?!Jl
!,? J
lpIO
JJC
aJXI
.,,)
xJno3
an
p II! s
thl-
p,!n
q px
cq.a
iciw
qlc~
5'0
1 11
(,,lAO
lllaJ
X,!
SC.,)
Sth
-p,!
lN,
lJ"s ,
+A!,
'!,>
),6’
0 >
II
> L'
O'0
s "0
,,Xl
!I, S
th-,3,
!lll,
,TJ\
:,,I
i
II
:SMfl[
,oJ S
T! 'th
l-pI!"
', A
Ill! J
O JJl
\ll!ll
,C!
lW"d
XII
JO
JOIC
XpII
! I
ll! S
C p;r
<n S
q ,lK
,
(lllth
l! Oh!N
IWO
.,,)
$'I
,
.I. lll
t,l!l (1
~3
I'!l".
,,li
lili
I~~~
~,~I
iI~~
~,~~
,,~~
= 11
X3,NI!
\l"
!l\!,S
llJ.W.
, l
,,,l!,
,,s
-, :,
A,,,,
1111
~llltl
l!~,J
01
,~",~'
"~,I
27
3111
Os3J
a,,,
p"l! il
JX3J
d
~,l!!l
.,ll!l
ll
J;ll,l
O J" Il
O!,!
S"dU
lO~
al,,
1,"~l
l!,l
lK&p
'I\l
.,ll"d
lllO.3
,'!l
l,'!A!
pll!
J\ll
"S J
O ,a
AJ,
J31,
$, ,
! \,,
!M J
II!J
XiO
0, T
,,q!Ss
Od "
'1 i
(,!lll ,
,
(&R
S9
.()
+ O
z’!N
- O
ztN
‘ha)
s-i
- S’
Z(OZ
1!,-.J ‘
t??)
S!,l!J
,VS’b
- 5
’1‘O
SR'
I -
2'1in
%
:(~pll
lS Jn
J lS
.7JW
! ,
l?!J"d
S J
O %l
!Sq S
W!K,
XJX.
,) W
3lll:J
%l
!AW,
,OJ X
,1 \
I! Il.
,+, d
,,I!Jl
t,~l
PJI! JW
!.71
,2Jd l
! JO
Sd
l!lS J
7h\O
, X,
1 II! p
.,ll!J
;l,"l
X,
Ill!.7 1
,2!',"
\ S
;l,!ll
!,nA
JO S
,,",,\
!J,,,l
.),,,,
r
'll0!1
1!~!~1
!! J
O xl!
&\ A
[, '
12Ill!
l',!
Z, X
II l
l! ti,
ql!J2,
Ol 8
110!11
!1111W
110.7
k&,
.X,C
0,
J;r,Ia
Jt, 0
, k,\
l.?(11
1.7)
I! S!
71.71,
1
XC,.
'Sll,!
!,
JW?I
,T)J
d
JOJ
Jaytl!
,:,
11" ,3 '7
A["'
"'.
a.?
'll,!r
y l
! \I! 5
,q!~~!
lll,w!
.“c]%:,qv%3!:J’(~OS)%3)Z’r,>r ::,‘(“oS)‘ry?( !alqw~~,,~:('pos)'y!<$ ~I!lI.,3IIX~
:('O>r3'('0!S)'V~~) >\!JJlltk DJF. ~~,'hllC~:,:SNl~l~~S ll,l?, IIIOJ) pWd>\\,>J ,"!J~ll!\\l \I,
,Xl,J!],,3,~! JJI! SpWlOdlll~~ W,',lllO2 Ja\IlO pill! '!lI.I,'SI~UllOJ3 J!llH!llr(pWlJal,l 1," p?I.,X,Y? ,"I,
i! -"OS*>('"OSIQZ - a,!u!rtq%a, rrmyr3 sC t~o~wslr~pi~o~ wJ!p '9.2 '~JU~JOJ spltn~11110~p,,l! p?l,S!,qC,S;, 7q hl!\ll l!!Jq!,!ll,,a Mall pill! St,OJp ~JW!JX,lllJI ,CllJ~lll! 'SWaJJll! S3ll!Il!O.,
JO SS;rU~~!l,l ?I,1 SV'StIrI-pl!nq arr!l!lr! - sm!~lrls I10 sl!scxl.,p lIl!rn Sl! _ ,wC Ufl!Sal[pC xne.2~,,'!1',,c, UK, ,fXIl !Sl1O!IX!~J ,,!"!"'~\I~ aY,OAOJd UCJ pXtJ >,,I 110 Sl!S"h~ '(Z aJn3!:,) Dew,*,,,",a', ,,JAa S,(1,11 p!ll,\!I JO \,"!,l!t\,JOJ 3\l!?.W,It! 'aJlll~J;lt,lll;ll <!\I1 II! ,'!'h, Sl1O!l!SW,l\10.7 ~,CJ,I,~
," 93llCJ alI1 SaWJXl! l,+,M ,3)( JO llO!I!ppC II! I,l!A\ ',l!!JW!lll 15,ll! "I!'( II! aSl!i,d ?lCJ,llF ll[I
JO llO!I!SOdlllO., al,) WC,llJ,El 01 3ll!lS2Jalll! IKllJO S! I, '(,L(j, 'llllt!lll~,!~,) a&f)8 b\O,"q SlJl!ls'OSl!3 po!yy /rOS'"N IllJlSh XJIWJ~\ 301 II! Ill!l,JW'~~ltTJ,ns !,l?~,I! p!lllJ!, se X,,C!l!ll!
h,q'!',flJd ISOIII "&,m,, - m(j 18UCJ Sl,l II! JSW,J110.7 S;lil!J,flS lSO,A, '(X,JnlS 2110 II! &OR,,l.32) ,calii MCJ p211!2,w X,IIWJJ Xq '0s JO 3~11idm JOJ ;IJ~\ICJXIIII~I urn111y10 uv s! 2~311.1.
'S;lll!.Y[lS Sll(llJCA J" llll!Il!lllJl!( X,l 3ll!,l!l! . .'Slll~Il,'lJl, thl-,l,l\lq Wt!Al!J3~l!
UPJ \IO!iCJl\tJJlJO3 % , pUllOJC OI atl!JOil,I JO \lO!lC[ll\llllJX! "II<,.',,%?lS JW!?l,"J', UlOllOq
a\,\ S,TJCMOI 13i\p JX!J alI1 JO ?Illl,Zl p"aJ ll,!?f a\Il \I! t,',l,aA?p W!J S&l-,l,!no '(~J\llCJX,\Wl
Jam01 k,,$h,s e iv ap!Jo,c,n tmpos) 3.006 pm ~8 unmmq sasl\ap\io3 auo,v ?~!Jo,I,~luri!sralo,, ~~ro!~e~rnlc~a \lr!ql uo!les~r;lpiro:, SU!IIJ;~A~~ e11~~10tt~r~d m ~J~III:J~I!~ ssa, r! 3JabI.I.
(TWXlJd Al,' X,, J" s;llll\,3kl Z?:~\!l~.!l,Wll 311, I,! \\1!,,, ,31!,\1!~.) ,N,"F/S!!?
alttu!1u! ssa, I,I!M 'paXo,d1117 s\JJa,sXs Qu!ilfa\I-2Jd J~,tliu!s 3\,1 c1;ln!3 'JT~~IXIJ~ s! u,!y XW,OJ71,l \!lOJJ X,\!X3 tl,!lt!,OA JO ,W"l,!,a~!, 311, l,~llfll,l," _ W,.h ,'!\"S,\l! JO SJ!l!,!C,!SSOd S!! ,,,7"\Sk' \1111,1J ,Stlp JO Sa,Jh ,,!llJ2,11 a&L!,, "Sa,,.,. 'kJ,\.!\llaS 'l?M-!\ll;ls ',3M - llO!~,ZJCd~lt, ,W,
II,!? JO SJall\1l!ll1 I\laJ7JJ!p JA[OAII! lIJ!I,M SSa2OJd ll,!J 1117111.75 a\(lJO S,i,l?!Jl!,? JlpIO JJC aJXI.,,)
xJno3 anp II! sthl-p,!nq pxcq.aiciwqlc~5'0 1 11(,,lAOlllaJ X,!SC.,) Sth-p,!lN, lJ"s ,+A!,'!,>),6’0 > II > L'O
'0s "0 ,,Xl!I, Sth-,3,!lll, ,TJ\:,,I i II
:SMfl[,oJ ST! 'thl-pI!"', AIll! JO JJl\ll!ll ,C!lW"d XII JO JOICXpII! Ill! SC p;r<n Sq ,lK,
(lllthl! Oh!N IWO.,,) $'I, .I. lllt,l!l (1~3 I'!l".,,lililiI~~~~,~IiI~~~,~~,,~~= 11
X3,NI! \l"!l\!,SllJ.W., l,,,l!,,,s -, :, A,,,,
1111 ~llltll!~,J 01 ,~",~'"~,I 273111Os3J a,,, p"l! ilJX3Jd ~,l!!l.,ll!lll J;ll,lO J" IlO!,!S"dUlO~ al,, 1,"~ll!,llK&p 'I\l.,ll"dlllO.3 ,'!ll,'!A!pll! J\ll"S JO ,aAJ, J31,$, ,! \,,!M JII!JXiO 0, T,,q!SsOd "'1 i(,!lll ,,
(&RS9.() + Oz’!N - OztN ‘ha)s-i - S’Z(OZ1!,-.J ‘t??) S!,l!J,VS’b - 5’1‘OSR'I - 2'1in
%
:(~plllS JnJ lS.7JW! ,l?!J"dS JO %l!Sq SW!K,XJX.,) W3lll:J %l!AW,,OJ X,1 \I! Il.,+, d,,I!Jlt,~lPJI! JW!.71,2Jd l! JO Sdl!lS J7h\O, X,1 II! p.,ll!J;l,"l X, Ill!.7 1,2!',"\ S;l,!ll!,nA JO S,,",,\!J,,,l.),,,,r
'll0!11!~!~1!! JO xl!&\ A[, '12Ill! l',!Z, XII ll! ti,ql!J2,Ol 8110!11!1111W110.7 k&,.X,C 0, J;r,IaJt, 0, k,\l.?(111.7)I! S! 71.71,1 XC,.'Sll,!!, JW?I,T)Jd JOJ Jaytl!,:, 11" ,3 '7A["'"'.a.? 'll,!ry l! \I! 5,q!~~!lll,w!
FIG
UR
E 3
OX
IDIS
ED
KIL
S S
ULFL
.iR C
YC
LE
(. .
. . . .
. . .
vapo
ur p
hase
: -
solid
ph
ase)
(fmm
raw
mat
eria
ls1
FIGURE 3OXIDISED KILS SULFL.iR C Y C L E
( . . . . . . . . . vapour phase: -solid phase)
(fmm raw materials1
‘1‘115 cffccls o n cliukcr iuay be sutntnariscd a s f o l l o w s :
I’luxinl: aclioii:
0 l o w e r lcmperalure o f firs1 l i q u i d phase f o r m a t i o n
l cbangc al’ l i q u i d viscosily
6 allcraliun 0r sdxx Iciisioii OK l i q u i d
0 inihlilic;il~o~i ul’ crystal ulorlhology.
I’l~ass rclaliurls:
I lydraulic aclivily:
l lhe fL’;iclivtlics 01’ lhc cliukcr u~immls arc allcrcd b y sul~d mlulion ;uldlor by
the cffccrs o f crystal syinrilctry (IQli leu~pcralure stabilization o f poly~norphs)arid/or cl’fucls occurritrg during liydraliotl (e.g., coaling of cc~uenl particles by
insolubly salis).
( I I i s d i f f i c u l t lo isolale Ihcsc Ihrcc classes of cffccl i i i praclics.)
I I I gcuc~al. incorporalioo of a d d i t i o n a l clillkcr solC;~~e it1 a situatioll willi e~.ccss a l k a l i s y i e l d s
a inore dilficuli “iiIlI>ilfCl\l grithhbilily” with adviiolagcs i n the Iua~kcl or hlmvctl e a r l y
concrclc s1rc11g111 a n d workabilily.
I’IIc cf~cc~r or utimJr ~WII~~II~IIIS WI the vircosily a n d shrlace lensioll of l i q u i d phascr c a n
be cou~plrx. Luwcr viscosiliss e n c o u r a g e alilc ( c a l c i u m lrisilicale) forinalion. CalciuiuSUIT;IIL flux call. I~ow~!vsr. stabilise bclilc ( c a l c i u m disilicatc) antll~r CatIsc lhr prodtrcliori o f
clinker alilc will1 lime i n c l u s i o n s . I:urlher, iu clinkers with a l o w alk;lli CWICIII, bclilc
sI;tibilis;dicm due III cxccts S O , Icxls I~I tlilliuulr cl,lnl,iii;ll,ilily. S~rtm~ly c h e m i c a l l y fcducir$
comJilioiis I I I Ilic burriiug LOII(: cau Live a camcril will! par Ilow cliaiaclcrislics (tluc lo I’rsc
K;,O a n d N+O), p o o r workhility ( d u e I O IIIC i n c r e a s e d conlcnl o f Iricalcium aluminalc arid
ils rraclivily), poor slrcuglh (lower lricalcium silicalc conlenl) a n d Vilriill)lt colour.
A l k a l i s rclainrd i i i clinker a r e prcscm cilhrr a s slablr sulhles o r iibSlllbd i n llld silicate aridalulnitialr siruc~urcs: ihcsc inlltrencc IIIC bchaviour o f fresh cor~crele a n d m o r t a r d u e l o Ilieir
various solubililier. N;r20 hi\s a I~\WC matkcd ~ende~\cy than K,c) 10 ~OIIII wI~II~IIS illc a l c i u m alurnimilr. I:or clinkers with (ruular) ratios of sulfiilc:lol;~l alkalis below 0.3, iIIItloSla l l 111e sulh~e i s combimxl ill waltz soluble form, K$O,, beill& prcddomimmt. A pruporlion
ol’ the a l k a l i s ale i n s o l i d soluiiou itI IIIC c l i n k e r aluciiinalr phase and lhis has ati advorle
rlfccl ori the inirial cc~~~cnI rcaclivily illld Illus o n comxele a n d morlaf r h e o l o g y .
For ralios belwceii 0 . 5 a n d I .O, a c e r t a i n quanlily of langbrinilc i s a l s o formed (and no1 a l l
lltr a l k a l i s a r e wlul~lc). I:or r a t i o s alrove 1.0, si~nilicanl f r a c t i o n s o f lhr Sulfales a r e
c o m b i n e d williin Ihc silic; .md aluminalss o r as auliydrirc (CaSO,). which d~s~I~cs umrcslowly III~II a l k a l i sulf’ales, whilst llle fraclions of K,O aud NazO which are s o l u b l e ill w;ucrapproach I .O ;mJ 0.S. rcspxiivsly. al a raliu OI’:IIJOUI I.S. Al sitll’alc:;ilk:ili raliiJ9 ahvc I .SIrcntls a r c wmewl~al crralic. I’ur IWSI uoru~l clinkers IIW prilicip4 rulli~~c phase w i l l bcalhil~italilc (Iwlassitlrri/roditr[rl s u l f a t e ) with a m a x i m u m WN;I r a t i o o f 3 . 0 . ‘I‘l~is IIllasc i saccompanied b y m i n o r quaniiiirs o f K,SO, a n d c a l c i u m Iangbsiniic. Na$O, bciug hmd
o n l y Ibr u n u s u a l l y l o w K/Na raiios.
A s w e l l a s lhe s o l i d solulion rffecls a n d the f o r m a t i o n o f compou~ids d e s c r i b e d almvr,
v a r i o u s permulaliotis o f volalilcs ( e s p e c i a l l y in Itie p r e s e n c e o f f l u o r i n e ) c a n influcrux rhc
s~ructurs arid belnviour o f aliic aml bcliir crysials ( M o i r & Classtx, l!J92).
II is gc~icf;~lly ~.up~~‘xd IhI (t~llicr Ihcl~~rs ljcitlg cqii;~lJ ll~c cxlcul 1,1’ vt8I:tlili*:tlit~ll ~~L,I~:I\c’I
a s the Iliermal efficiency a l IIIC kiln iucrcascs. ‘I’liis i s prol~ably du1: Iu iltc lillliliug sllUcio f vapur wluralion b y a l k a l i c o m p o u n d s , a s c o n f i r m e d b y sludics of IIIC irca~msm o f k i l n
dusl i n a I00 IIII~ diarnslcr hidiscd bed (‘l’clinnr rf ul, 1978) lo e x a m i n e ihc fcasibili~y o fproduciril: cliriker ~~OIII WIII~III kilt1 flue dull will1 caplure of IIIC a l k a l i s distilled f r o m 111l:
b e d for p o s s i b l e use ill 111e ferliliscr i n d u s t r y .
I I i s su~gerlcd IIuI !II
V’ = -me..llilllM,1-.-.(1' - 1") WJ
v* i;i salurhtd vapour coiicciilralioii i i i Irai~sporl pscs ( k g / k g )p* = wluralrd vapour p r e s s u r e 1
OT au a l k a l i compouml ) ~:IIIIC imilsJ’ = g a s pcssur~ 1M, = niolrcul;ir wcigld III’ valmiir
M, = m o l e c u l a r weigh1 o f g a s .
Give0 malluzmalical cxprcssiims f o r S;~lt~rillI2~l vapour prcssltrcs ilS ~m~ciicms of lc~llpcralurua n d krmwlcdpz of kill) systru~ Icmpcralurc p r o f i l e s , the w~ura~cd val)uur conccmraiioll WI
be calculaled f o r exh a l k a l i compout~d a n d IIIIIS he maximurn qu;miiiits cval~ra~cJ f r o mllle feed lxx unit IllilSS of g a s e s . ‘I’lieri, considcrirlg the amoums ol’ gas passirlg Il~rou~:h lhckih al v a r i o u s temperatures, llx Iruc llllillllily ol volaiilcs Irar~sp~rlud per uuii m a s s o fc l i n k e r GUI be calc~tla~txl arld f r o m his krtowlcdp, ‘ideal* volaiilc cycles CarI lx tlsduccd.
For example, saturated vapour pressures at IZOO’C are (for IIIE prrc substances):
K C I 0. I8 am
K,SO, 0 . 8 x lo” illIll (0.6 x IO’j am with dccolnpition suI~Imssec1)Na$O, 0 . 1 3 x IO’] alIll (0.01 x IO” ~IIII with d e c o m p o s i t i o n s u p p r e s s e d )
‘1‘115 cffccls o n cliukcr iuay be sutntnariscd a s f o l l o w s :
I’luxinl: aclioii:
0 l o w e r lcmperalure o f firs1 l i q u i d phase f o r m a t i o n
l cbangc al’ l i q u i d viscosily
6 allcraliun 0r sdxx Iciisioii OK l i q u i d
0 inihlilic;il~o~i ul’ crystal ulorlhology.
I’l~ass rclaliurls:
I lydraulic aclivily:
l lhe fL’;iclivtlics 01’ lhc cliukcr u~immls arc allcrcd b y sul~d mlulion
;uldlor by
the cffccrs o f crystal syinrilctry (IQli leu~pcralure stabilization o f poly~norphs)arid/or cl’fucls occurritrg during liydraliotl (e.g., coaling of cc~uenl particles by
insolubly salis).
( I I i s d i f f i c u l t lo isolale Ihcsc Ihrcc classes of cffccl i i i praclics.)
I I I gcuc~al. incorporalioo of a d d i t i o n a l clillkcr solC;~~e it1 a situatioll willi e~.ccss a l k a l i s y i e l d s
a inore dilficuli “iiIlI>ilfCl\l grithhbilily” with adviiolagcs i n the Iua~kcl or hlmvctl e a r l y
concrclc s1rc11g111 a n d workabilily.
I’IIc cf~cc~r or utimJr ~WII~~II~IIIS WI the vircosily a n d shrlace lensioll of l i q u i d phascr c a n
be cou~plrx. Luwcr viscosiliss e n c o u r a g e alilc ( c a l c i u m lrisilicale) forinalion.
Calciuiu
SUIT;IIL flux call. I~ow~!vsr. stabilise bclilc ( c a l c i u m disilicatc) antll~r CatIsc lhr prodtrcliori o f
clinker alilc will1 lime i n c l u s i o n s . I:urlher, iu clinkers with a l o w alk;lli CWICIII, bclilc
sI;tibilis;dicm due III cxccts S O , Icxls I~I tlilliuulr cl,lnl,iii;ll,ilily. S~rtm~ly c h e m i c a l l y fcducir$
comJilioiis I I I Ilic burriiug LOII(: cau Live a camcril will! par Ilow cliaiaclcrislics (tluc lo I’rsc
K;,O a n d N+O), p o o r workhility ( d u e I O IIIC i n c r e a s e d conlcnl o f Iricalcium aluminalc arid
ils rraclivily), poor slrcuglh (lower lricalcium silicalc conlenl) a n d Vilriill)lt colour.
A l k a l i s rclainrd i i i clinker a r e prcscm cilhrr a s slablr sulhles o r iibSlllbd i n llld silicate aridalulnitialr siruc~urcs: ihcsc inlltrencc IIIC bchaviour o f fresh cor~crele a n d m o r t a r d u e l o Ilieir
various solubililier. N;r20 hi\s a I~\WC matkcd ~ende~\cy than K,c) 10 ~OIIII wI~II~IIS illc a l c i u m alurnimilr. I:or clinkers with (ruular) ratios of sulfiilc:lol;~l alkalis below 0.3, iIIItloSla l l 111e sulh~e i s combimxl ill waltz soluble form, K$O,, beill& prcddomimmt. A pruporlion
ol’ the a l k a l i s ale i n s o l i d soluiiou itI IIIC c l i n k e r aluciiinalr phase and lhis has ati advorle
rlfccl ori the inirial cc~~~cnI rcaclivily illld Illus o n comxele a n d morlaf r h e o l o g y .
For ralios belwceii 0 . 5 a n d I .O, a c e r t a i n quanlily of langbrinilc i s a l s o formed (and no1 a l l
lltr a l k a l i s a r e wlul~lc). I:or r a t i o s alrove 1.0, si~nilicanl f r a c t i o n s o f lhr
Sulfales a r e
c o m b i n e d williin Ihc silic; .md aluminalss o r as auliydrirc (CaSO,). which d~s~I~cs umrcslowly III~II a l k a l i sulf’ales, whilst llle fraclions of K,O aud NazO which are s o l u b l e ill w;ucrapproach I .O ;mJ 0.S. rcspxiivsly. al a raliu OI’:IIJOUI I.S. Al sitll’alc:;ilk:ili raliiJ9 ahvc I .SIrcntls a r c wmewl~al crralic. I’ur IWSI uoru~l clinkers IIW prilicip4 rulli~~c phase w i l l bcalhil~italilc (Iwlassitlrri/roditr[rl s u l f a t e ) with a m a x i m u m WN;I r a t i o o f 3 . 0 . ‘I‘l~is IIllasc i saccompanied b y m i n o r quaniiiirs o f K,SO, a n d c a l c i u m Iangbsiniic. Na$O, bciug hmd
o n l y Ibr u n u s u a l l y l o w K/Na raiios.
A s w e l l a s lhe s o l i d solulion rffecls a n d the f o r m a t i o n o f compou~ids d e s c r i b e d almvr,
v a r i o u s permulaliotis o f volalilcs ( e s p e c i a l l y in Itie p r e s e n c e o f f l u o r i n e ) c a n influcrux rhc
s~ructurs arid belnviour o f aliic aml bcliir crysials ( M o i r & Classtx, l!J92).
II is gc~icf;~lly ~.up~~‘xd IhI (t~llicr Ihcl~~rs ljcitlg cqii;~lJ ll~c cxlcul 1,1’ vt8I:tlili*:tlit~ll ~~L,I~:I\c’I
a s the Iliermal efficiency a l IIIC kiln iucrcascs. ‘I’liis i s prol~ably du1: Iu iltc lillliliug sllUcio f vapur wluralion b y a l k a l i c o m p o u n d s , a s c o n f i r m e d b y sludics of IIIC irca~msm o f k i l n
dusl i n a I00 IIII~ diarnslcr hidiscd bed (‘l’clinnr rf ul, 1978) lo e x a m i n e ihc fcasibili~y o fproduciril: cliriker ~~OIII WIII~III kilt1 flue dull will1 caplure of IIIC a l k a l i s distilled f r o m 111l:
b e d for p o s s i b l e use ill 111e ferliliscr i n d u s t r y .
I I i s su~gerlcd IIuI !II
V’ = -me..llilllM,1-.-.(1' - 1") WJ
v* i;i salurhtd vapour coiicciilralioii i i i Irai~sporl pscs ( k g / k g )p* = wluralrd vapour p r e s s u r e 1
OT au a l k a l i compouml ) ~:IIIIC imilsJ’ = g a s pcssur~ 1M, = niolrcul;ir wcigld III’ valmiir
M, = m o l e c u l a r weigh1 o f g a s .
Give0 malluzmalical cxprcssiims f o r S;~lt~rillI2~l vapour prcssltrcs ilS ~m~ciicms of lc~llpcralurua n d krmwlcdpz of kill) systru~ Icmpcralurc p r o f i l e s , the w~ura~cd val)uur conccmraiioll WI
be calculaled f o r exh a l k a l i compout~d a n d IIIIIS he maximurn qu;miiiits cval~ra~cJ f r o mllle feed lxx unit IllilSS of g a s e s . ‘I’lieri, considcrirlg the amoums ol’ gas passirlg Il~rou~:h lhckih al v a r i o u s temperatures, llx Iruc llllillllily ol volaiilcs Irar~sp~rlud per uuii m a s s o fc l i n k e r GUI be calc~tla~txl arld f r o m his krtowlcdp, ‘ideal* volaiilc cycles CarI lx tlsduccd.
For example, saturated vapour pressures at IZOO’C are (for IIIE prrc substances):
K C I 0. I8 am
K,SO, 0 . 8 x lo” illIll (0.6 x IO’j am with dccolnpition suI~Imssec1)Na$O, 0 . 1 3 x IO’] alIll (0.01 x IO” ~IIII with d e c o m p o s i t i o n s u p p r e s s e d )
‘I’lrc I~;III~IKJ~( capacity 14 air lo; vapours al lZ(XJ”C i s tbur: nil - 7(X1 g/1;: K,SO, - 1 g/1::Na ~SO,, < 0.S 1:/g. ‘I’hc cqj;lcily nl I?S(l”C i s ;IIJ~JIII I W O limes bil;llcr.
II cmi IljcrcInrc hc Iurcsccn Ilral (unless llic equilibrium vapour prcssurcs difCcr grally Iromurlur;jlrA values) lbcrc w i l l b c lilllc problem i n removing KCI from m a n y k i l n lluc dusls ina lluitliscd IJC~ witli a g a s llow ralc o f , say , 2 g per grammc o f dust, idll10ugb Ibe c a p a c i t yC0r sdhk removal m a y b c limilcd. The sa111c reasoning a p p l i e s 1 0 k i l n s , will1 wcl processkilns typically slmwinl: n ratio rjf a lilllc less 1ljan 2 g/g gas/solids in ~ljc burning z0rjc and‘pcrljapr 2 . 7 5 l;Ig ;II IIW b a c k end. will1 corrcsl~nding values C0r lljc d r y prtxzcss (wilboulI)rcc;jlcitl;lliolj) Or I .4 ~$1; and I .91 g/g.
I)c\pilc IIIC lacl IIWI qualilalivc diCCcrcr1ccs I~c~wcc~~ I W O k i l n s (OIJC d r y process a n d OIJC wet)arc rrllcclctl in s:jmplc calculations, Suclj “idcal” calcolalctl rccirculalinl; loads arc aboul IOIimcT lnrjicr lljn~i tllosc cricounlcrcd i n praclicc. TIJC probable reasons include:
3)
11)
cl
(1)
Cl
0
b)
In~~~w~~lclr ct~~~l:wl Iwlwccn g:iws :uul s o l i d s i n llir k i l n . wlicrc o n l y a sii1;1llI’raclitui 01 lltc s o l i d surracc i s cxlxjsrd a l ; I given lime. ( I I i s cxpcclcd llialIbcrc i% bcllcr coril;~cl i n llic cc~lrlcr dusly rqiojis Or lbc syslct~~.)
Vul:llilis:llion c:b;lr;lclcrislics of IIIC alk:lli-ccrlJl;lirliIlg IniItcritIs ;,I a givcu IJI;IIJI.i.c., conrljinnliorl i n m0rc co~~iplcx silicalcs a n d aluminalcs. 1~01 o n l y sijihks.I’raijspfjri 0r co~~jp~rintls wljicb arc condcnscd as/on solid dusl or rtl0lc.
I~~Ictluciion nl vap0ur prcssurc over scjlulions of a l k a l i c o m p o u n d s .
i~~lq~~c lrcnlmcnl d ibc Irnjjspjrl or ljcal and Or vnfxnjr willrin UJC bed Orclicikcr nodules i n Ihc kill).
I:orrnsliotj Or Olbcr compounds. e.g., CaSO,, dcpcndin~ on alknli:sullaic ralio.
I~rjs~al~lc opcralion or p r o d u c t i o n k i l n s : praclical c o n d i t i o n s a r c 1101 cxacllyIl~osc cxl~clcd k)r very l o n g lcrm slabilily Or lcmpcralurc a n d malcrial Ilow.
Tbc lurillcr tlcvclqjnrcn~ or a prctliclivc model w i l l Ijavc I O iakc accour~l o f such [actors, aswell as illc crrccls Or coni~xlsilion Or kiln almospbcrc. In rcccril ycnrs llicrc has been mucllinvcslig:llirjtj ol l;jclors /:nvcrninp, IIIC block;tgc of cyclones a n d lbcir pcc’k~rmancc i n biGIIcurpcralurc coal c~11iil~5lion proccsscs (itI Ilic Iiopc or prolccling Iurbinc blatlcs i n tlirrclcycle clcclric power gcucr;tlicln syslcms). Wljcn linic (or limesi0nc) i s injcclcd lo nbsorbS O , . 111~ COIJI~HJ~JI~S a n d Il~crrnodynamic crilcria invoked a r c cxaclly 1110s~ cncounlcrcd inIIIC CCIIKIII intluslry - particularly wl~cn rclalivcly l1igb cbloridc coals arc oscd. II is probableIllal Iljcrc i s now sullicicnl n c a d c m i c knowlcdgc IO bclicr Irc31 o u r silualion a n d a l l o wimprovctl mrxlcllinl; a n d undcrslanding. Anolbcr aspccl 10 consider is knowlcdgc acquiredrrnm sludy 0r ibc rcgciicraliori 0r CaO sorbcrils u.sul ror S O , s c r u b b i n g : a g a i n , dalap0lcnlially rclcvanf in k i l n sys~cms arc protluccd, l’or cxamplc, o n p r c s s u r c s o f S O , i n IIICsy~cm CaSO.,I C;rSI CnO i n IIIC prescncc ol v a r i o u s conccnlrations ol C O a n d C O , . II isImpcd Illal ibis paper promolcs cross-rcrliliulion bctwccn IIJCSC v a r i o u s fields or w o r k a n dlbc bcnly oC praclical knowlctlgc available i n ~ljc ccmcnl i n d u s t r y .
‘I’IIANI<S
‘l’ltis Ical. ori~;in;llly I~lsul o n v a r i o u s irjlcrn~tl amI crlcrr~l rqK)rIs, Ita\: l~ccrj atl;~l~lcd 01t lllcb a s i s of urchjl di.uzussion will1 Icclmical slall rrom a mrmbcr ol ccmcnl companies. 7‘banksarc given lo all involved, as well as IO lbc Directors of WIIC Circle Industries PLC ror lbcirpermission I O publish Ibis paper.
Clioi. G.-S. & Glaswr, 1:. I ’ . (19RR).‘I’bc Sulplrur Cycle i n Ccmcn~ K i l n s : Vap0urI’rcssurcs and Solid~l’liasc Slabilily O r llrc Sulpbalc I’ljascs. Ccr~~ct~l rind ConcrrlcIlcsc:~rcl~, IR. 367.371.
Kct~n. C . I ’ . & M u r r a y , It. 1. (1984). I’ortland CCIJIOJI I’rotluclicm. 111 Slntcljtrr nntlI’crlonnnnrr oC CWICII~S. c c l . I ’ . Ilarncs. Appliccl Scicncc I’ublisltcrs I.id. Ihrkirj~. ~IJ 705.7 . x
M o i r . (i. K . & Gksscr, I:. I ’ . (lYY2). hlincrnliscrs, h4otlificrs a n d Activators i n ~ljcClinkcring I’rr~css. In 9111 It~lrrwtliowjl Corjgrcsi ~IJ lljc Cljcjrjislrg or CCIJJCII~. NCWDribi, I n d i a , 1 9 9 2 : Congress Itcporls, Vnlumc I , National C o u n c i l r0r Ccmcnl a n dIluildirj~ Malcri:tls, New Dcllji, p p . I2S- 154.
Rilzmann, I l . (1971). C y c l i c I’bcrtomcna i n Rotary K i l n Systcrr~s. ~cjrlclll-l(nlk-Gip(, 24.338-343.
I’cllmar, n.. Kljor, I . I I . . k Gregory, S . ( 1 9 7 9 ) .Glps, 3 I , 288-290.
I’roccrsing or K i l n Dusi.
APPExmX 3
PAPERPRESENTED BYT MLOWES
100% Pet Coke - Problems and Solutions
100% PET COKE - PROBLEMS AND SOLU-I-IONS
“Good morning Lady and Gentlemen,
The citie of my paper is 100% Petcoke - Problems and Solutions.
It will give information on how Blue Circie Cement has moved from zero to 40%petcoke over a 3 year period, indicating the technological problems that need to beovercome for any works that seeks to fire 100% petcoke.
Before beginning my presentation I would like to thank Gerard Flament of CCB andJean Pierre Piliard of Ciments Lafarge for their help and information during thisdevelopment phase within Blue Circle Cement.
The paper mainiy deals with the dry process. However, the conclusions apply to wet,LepoI and long dry processes.
Slide 1
This overhead indicates BCC’s approach to petcoke. Firstly, prior to 1991 there waszero use of petcoke because ic was coo much trouble and low ash coal was much“NICER”. However, in 1992 due to a significant recession, we moved up to 30%replacement and in 1993 40% overall on 10 Works. Some Wor:ks using none, 100% usageat times on a Lepol process, 80% on the large semi-wets at Northfleet and 65% on awet process at our Masons Works.
In 1993 the prices increased, consequently the financial benefit accrued to the projectwas only the same in 1993 as 1992.
In 1994 there has been a slight market improvement, some Works can se11 everythingthey can make and consequently we are already failing to meet the 1994 plans for useco petcoke.
Slide 2
This slide gives some indications of why one should use petcoke. Firstly, its price can.be up to, and sometimes even more than, 50% less than the coal price per GJ. It canimprove cement quality, if there is an excess of alkalies over sulphates. In addition, ifyou are coal mill limited on cement olant output it can, with the appropriate Hardgroveindex, increase coal mill capacity.
In addition, it can be claimed to help the environment as petcoke needs to be burnt andif it is burnt in conventional power stations the SO, emission {vi11 increase, whereas inmost Of our processes it is significantly retained. However, the real reason for usingit is that in a recession, the full kiln OUtpUt is not reouired and consequently operationalcosts are at a premium and petcoke can make a significant reduction in OperatiOnalcosts.
Slide 3
This siide indicates reasons for not using petcoke. Firstly, it can increase SO?emissions, this even applies to a certain extent within a dry process as, for example,even in a precalciner betueen 6000 and 10000 ppm SO, is the maximum that can beabsorbed before bypass into the preheater sys=m occurs.
Due to the extra S02/S03 going into the system I don’t need to celi anybody there issignificant increase in potential for ring formation and blockages. In addition theblending operations are increased unless one is reaily firing at 100% petroleum coke..AIso there can be coal mill fineness problems having to meet the lower 90 micronresidue and there is more variability in sulphur and Hardgrove index. in addition, someinvestment may be required.
Slide 4
This slide identifies the main problem of using petcoke which is controlling the S02/S03cycles which leads to blockages and increased SO? emission.
This depends on the total SO3 input, the Na30 equivalent, the molar ratio of SO3 toalkaiies in the clinker, the combinability temperature of the clinker and in addition tothis, how well the kiln is controlled and the overall flame conditions that exist withinthe kiln.
Slide 5
This slide shows some facts concerning peccoke usage. Firstly, for price reasons themain interest lies in the higher sulphur petcoke which typically varies between 44% andS+% suiphur. For a dry process kiln with 800kcal/kg using 100% of a 5% sulphurpeccoke, this is equivalent to around 1.33% SO3 on clinker.
As most Works are limited to around 0.6 Nay0 equivalent, this corresponds to amolecular ratio of 2 to a clinker SO3 of 1.5%. -
.Above a molecular ratio of I, calcium iangbeinite, which is a salt of alkali and calciumsulphate with 2 molecules of calcium sulphate for 1 of potassium sulphate, forms inaddition to calcium sulphate.
Calcium lambonite decomposes at around 152O’C leaving alkali and calcium sulphate.Calcium sulphate decomposes at 145O’C. However, these decomposition temperaturesare both in the presence of excess oxygen.
If there is in excess of 2000 PP?J of CO in contact with caicium sulphate above a1000°C it would break down to SO3 and calcium oxide and hence exacerbating anyparticular problems one has with SO2 emission and preheater/kiln blockages.
For a molecular ratio greater than 2 in stage 4 raw meal, this generally is recognisedas producing hard deposits.
Slide 6
This slide shows what conditions you need to avoid and what conditions you need to haveto be able to use 10096 petcoke.
Firstly, the conditions that need to be avoid& are chemical reduction in the burningzone, Over-burning and low Na,O equivalent. For 1009/o petcoke one needs to have agood flame, a readily combinable raw mix and a good kiln control of free lime and backend oxygen.
Slide 7
This slide shows what are the requirements of a good flame and uses the CEMFLAIME1 information fairiy extensively.
One needs to ensure that the burner has adequate momentum, e.g. around 7N/MW. Thisis to ensure that there is adequate air available to combust the voiatiles and carbon ofthe peuoleum coke on a micro mixed basis before the petcoke comes in contact wirhthe burning zone at between 2 and 3 kiln diameters, depending on wheKher one has ahigh swirl or a zero swirl burner.
It is importam Khar the ignition takes places very near the burner, a 60% bluff body willhelp to promote Khis by removing the jet establishmenr. region and creating an internalreverse flow zone. In addition, a secondary air temperature of greater than 800°C isrequired to achieve this early ignition.
Petroleum coke is a by-product of a process which essentially means that all of thelower temperature volaciles have been extracted and therefore peuoleum coke needsto reach around 900°C before its first volatiles can be released.
TO cope with this lower volatile release rate and notentially a less porous stiumre ofthe carbon as a result of its formation process, a’90 micron residue of around 6-7% isrequired, following the general rule of +90 micron residue being 50% of the volatilematter.
In addition, it is absolutely essential that a uniform enKrainmenK of secondary air takesplace into the flame, particularly ensuring that the secondary air coming under theburner is not SKarved. To ensure the maximum possibilities a burner cenually lined u?the kiln is most important.
Even if all of these criteria are met, one will still operate in reducing conditionpromoted by unburned carbon and CO if there is not adequate conuol of the back endoxygen. A recommended level is around a minimum of 3.5%.
Slide 8
This slide shows results from the CE:VFLAME 1 trials which indicates impact of backend oxygen on CO for both a medium volatile coal and flexicoke, with 90 micronresidues of 1246 and 2%.
T’he measurements are made at the back end of the kiln simulator which is equivalentCO an L/D of 12. As you can see, for the flexicoke, co ensure r.har: rhere is a CO levelless than 1000 PPM, one is essentiaiiy looking for 349’0 oxygen. A similar condition isi?Ot necessary for a medium voiatiie coal where ic does look char: in Che a-?;% regionthe conditions for less ihan 1000 ?Phl can be achieved.
Slide 9
This slide shows a typical situation on our dry process Works at Hope which indicatesthe impact of hard burning and CO/oxygen on stage 4 SO3. Hope Works has a clinkerMolar Ratio of 2 with a British Coal.
This was for a high volatile coal with a 90 micron residue of around 15% with the burnerlined centrally up the axis and a momentum of at least 7NI1MW.
It can be seen that hard burning increases the amount of SO3 in stage 4. However, italso increases the amount of NaZO equivalent and consequently not until one gets abovearound 1300 ppm of NOx is there a significant increase of excess SO3 over alkalies dueCO the thermal breakdown of calcium sumhate in the burning zone.
However, the most interesting point is the impact of back end oxygen OR the level ofCO and its consequent impact on stage 4 SO3.
It can be seen that once the back end oxygen drops down beiow 1.8%, i.e. to 1.4%, theCO increases from 500 porn to 2500 ppm and a corresponding increase of stage 4 SO3from 3.2% to 4.5%.
Under the conditions of the experiment, around 24 times the Na30 equivalent in theclinker was appearing the in stage 4 raw meal. Consequently, fo; a molar ratio Of 2,this corresponded to around 3.75% S03.
It can be seen that under reducing conditions promoted solely by the lack of back endoxygen, the SO3 in stage 4 increased to 4.5% which is a totally unacceptable level andblockage problems occur on the Works at this ievei.
The Works normally seek to run at around 3% stage 4 SO;.
Slide 10
While a good flame is important, alone it is not enough.
Good kiln controi is required, i.e. using Linkman, to avoid continual SO3 recycling. Forexampie, if one has a blaster operadon that breaks down deposits, if once it reaches theburning zone the conditions are SO hot that 90% of the SO3 is sent back into thepreheater system, obviously the blaster operations are not being suitably supplemented.
In addition, it is very important to have a combinability temperature essentially lessthan 1500°C. Also, one operates at round about I-I?XJ free lime, or else a similarsituation exists as to that I referred to previously under the need for good kiln conuol.Otherwise a continual recycling of the SOTin the syste.m wili occur leading topermanent problems associated with blockages and breakaway.
In addition, it is important that one continually checks what is achieved for the stage4 material. Preferably, this is supplemented by an SO2 probe that can be used tomonitor what is happenin g in the back end of the kiln and even be linked into the highlevel control. For example, 3000 ppm of SO7 equates to around an extra 1.05% SO3 onstage 4 raw meal.
Slide 11
And finally, in conclusion, now we know how to do it, how can 100% petcoke be usedwith lower NOx emission, bearing in mind this normally mea&u running into on the vergeof reducing conditions?
The answer is, I don’t know at the moment. However, CEMFLAIME 2 which is due totake place at the end of this year, will provide the answer.
Thank you”
--__-._---_- ---
100% PET COKE - PROBLEMS AND SOLbTIONs]_... -_-_.. _--_-_.- --- ------.---- .-.. -__-
o BCC's approach to Pet Coke
- Prior to 1991 zero use too much trouble, low ashcoal much “NICER”
- 1992 - 30%
- 1993 - 40% 100% Lepol, 80% semi wet, 65% wet.
- 1993 prices increased
- 1994 market improvement
- 1994 budget 35%
-(0Ci
53m-0s
0)Ci9
0dY0
I
-Ii-
fI1
-
i-
8us-8b8ul
0ti0d-
0cd--:
0ti-
PLn
-
t1if(I ’
-
i?0k3
1,
I-_--..---___ ____ - __...-- _-__- . .._ _.. -I__-__-_--. -
1
1 100% PET COKX - PROBLEMS AND SOLUTIONS /I-- -.-_-. ..-._.- . ..__._ _-. -. -_.-.._ ._.. - .__... _ _-. _- ,_.___ ,.__ -___ _.------_-_--.---__-- -___--. -- 1
l Why use Pet Coke?
A Price - up to 50% < Coal/Gj
A Improve cement quality
A Increase coal mill capacity
A Help the enviroment
A Recession, fxlll kiln output not required
r --- -_- _ -____. --__ ___.______ _.__ __,_____-_I__., _ -._____ ____ _ __._ _ __-- I/ 100% PET COKE - PROBLEMS AND SOLUTIONS.-.-_ - -..-- -_.-.- . .- . ..-.--- . ..--.. I .._ _._- ~----.-__.--.- -.----.-. _------ ,I--.----
o Why not use Pet Coke?
A Increase in SO2 emission
A Increase in problems with rings and blockages
A Blending operations increased
A Coal mill fineness problems
A S ,and Hardgrove variability
A Investment may be required
.---__-__-.__-_- -.-__ --__ ..-- . . .._.- -_,.-..-. __.._______ -__- _---
11000/o PET COKE - PROBLEMS AND SOLUTIONS1 _.--.-__-- ____.-_ --_.-. __--.. ___ .._....-... -.. .__- - -__.__ ._. ._-_____. --____-__---
o Main “PROBLEM”
A Controlling SO2/SO3 cycles which leads to increasedblockages and SO2 emission
0 Depends on:-
A Total SO3 input
A Na20 equivalent
A Clinker Molar Ratio
A Combinability Temperature
A Kiln Burning Control
A Hame Conditions
.-- -------- -_---- -- --
100% PET-COKE - PROBLEMS AND SOLUTIONS]--- -_.--- -___--.-. ------- .__
A 5% S Pet Coke - 100% usage - 800 kcals/kg - 1.33% SO3 onclinker
A For 0.6 Na20 eq. MR = 2 for Clinker SO3 of 1.55
A Above a MR of 1, K2S04.2CaS04 - Calcium Lambiniteand CaS04 form
A Calcium Lambinite decomposes at 152OC, CaS04 -145OCin Excess 02
A 2OOOppm CO at above 1OOOC breaks down CaS04
A MR >2 in Stage w ray meal produces hard deposits.I ,
-._-.- ---__-_--------.-... ----
FT COKE - PROBLEMS AND Sx-j---- _- --_--- - - _--~____.--- __.____ -_.. -_.__._. _ ,_ __-.- -.--. ..-- - - --.--
l FOR 100% Pet Coke need to AVOID:
A Chemical Reduction in Burning Zone
A Over-burning
A Low Na20
o For 10096 Pet Coke need to IXAVE:
A Good FLAME
A Combinability < 145OC
A Good Kiln Control of Free Lime and Back Endoxygen
--.----------..-.. _ --...-_ ---..... --. ..-. ------
1 100% PET COKE - PROBLEMS AND SOLW=].-.. -. _---_. - -..-_--..- -.__.._ - _. . .._ -._.._-_ ..__ -_----_.. ---- . . ..-- - - - - -
l Good FLAME as per CEMFLAME 1
A Burner Momentum - 7 N/MW
A Bluff Body 60%
A +9Ou residue 50% VM
A Central Burner
A Secondary Air > 800C
A Back End Oxygen - 3.5%
I !
I i
<
100% PET COKE - PROBLEMS AND SOLUTIONS- - - - -. . - c . -. .--~-.-- -.--- _-- -_--.-.-- ----
------.- ._-.-- - .-.-... .-. - ___._ _.__. ____ . . ._-------P-w-- .--.-...-...---------- ------I
0 Good FLAME alone not enough need:
Ilr. Good Kiln Control - Linkman to avoid continualSO3 recycling
A Raw meal residue low enough for goodcombinability
A 14.5 % Free Lime.
A Continual checking of performance
A SO2 probe to monitor and control, eg 3000 ppm= 1.05% SO3 on Stage IV raw meal
dI
0
\! ! *I ,. ’I4
i!
- . . - .__- _-__.,. - _ - _ -.-- _..--___ ..__ .-- .__- --_----___-
-COKE - PROBLEMS AND SOLUTIONS]I.-.- _-~ .____. __.--,. . ..: ._I -.-... ---. . - -. .I __.__ _... _,_. ..__.____ ---... I_-_-
o Now we know how to do it!
0 How can 100% pet coke be used with lowNbx emission
CEMFLAME 2 has the ANSWER
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 2
CETIC Sub Commission “Behavior ofVolatile Material in Kiln Systems”
ISTN 9215
CETIC ~~-C~~~~IssIOh’ “BEHAVIOtiR OF VOLATILE lMATERL4~ J.N =NSYSTEMS”
REVIEW OF “CLASSICAL” ECNOWLEDGE ON &mOR ELE&fEiiS - JUNE 1992
Summary
This report is based upon various documents originating within 3lue Circle and from externalsources, supplemented by accounts of experience in Works operated by CETIC membercompanies. A review is given of factors governing the behaviour of minor feed constituents(Cl, K, Na, S) in cycles originating i!t the kiln burning zone and of the consequent effectson process plant performance. Recirculating loads of volatile species are formed and theseare often implicated in the formation of build-ups, coatings and bloc.kages in cooler parts ofa kiln system. Some relevant practical experience is listed and implications for productquality are summarised.
In a given plant, burning zone temperature and atmosphere are the dominant driving forcesfor these cycles. A key area for action to gain control lies in the selection and preparationof fuels, burner settings and raw materials. Process control (including dust management) canalso be important, especially as regards selection and maintenance of sensors which givedirect or indirect information on burning zone atmosphere (i.e., chemically reducing oroxidising with respect to the volatiles). Several dry process Works have found useful resultsfrom study of the results of sampling and analysis of kiln entry meal on a regular basis.
Differences between pIants may arise from design features or from characteristics of rawmaterials and fuels. Various modifications :o details of process design and operation/ controlmay be used to alleviate plant difficulties or modify clinker quality, depending on the localpermutation of inputs and temperatures which is involved. For exampie, changes may bemade to cyclone geometry or “non-stick” linings added, or benefits may be found fromalterations to raw meal or fuel chemistry. These factors may also be considered whenselecting new equipment.
The prospects for further improvements in understanding and modelling of processphenomena associated with volatile cycles have improved in recent years with the completionof relevant thermodynamic studies in other areas of technology. The addition of secondaryfiring or precalcinarion can significantly alter the behaviour of some kiln systems, andappiication of the improved academic knowledge to some relevant situations may be worthyof encouragement.
IS-m 9215
CETIC SUB-COiMiullSSION ‘BEHAVIOUR OF VOLATDLE amTERI4L.S IN KILNSYSTEMS”
REVIEW OF “CLASSICAL” JKNOWLEDGE ON IMINOR ELEMENTS - JrJiuE 1992
1.
2 .
3 .
4 .
5 .
6 .
7 .
CONTENTSPage No.
INTRODUCTION 1
VOLATILES: WHAT ARE THEY AND WHAT ARE THEMECHANISMS OF VOLATILISATION? 1
CYCLIC NATURE OF VOLATILJZS N KILN SYSTEMS 3
3.1 EFFECTS OF VOLATILE CYCLES3.2 WET AND (LONG) SEMI-WET PROCESS3.3 LEPOL PROCESS3.4 DRY PROCESS
CHANGES N PROCESS CONDITIONS WHICH CAN INFLUENCEBERAVIOUR OF VOLATILES 7
4.1 PARAMETERS NFLUENCNG VOLATTLE RECIRCULATION4.2 ITALCEIMENTI4.3 CBR4.4 LAFARGE4.5 OBOURG4.6 CMENTS FRANCAIS4.7 ENCI4.8 HOLDERBAlNK4.9 BLUE CIRCLE
EFFECTS ON CLINKER 1 3
Sulfate retentionReducing conditionsFundamental aspects
TOWARDS A MODEL OF VOLATILE CYCLES 14
EFFECTS OF CONDENSATION 17
CETlC SUB-COIMMISSION “BEHAVTOUR OF VOLATILE IMATERIALS IN KILNSYSTEMS”
REVIEW OF “CLASSICAL” KNOWLEDGE ON mOR ELEMENTS - JUNE 1992
1 . INTRODUCTION
This text, originally based on various reviews available within BCI and on external literature,has been adapted on the basis of discussion within the CETIC “Volatiles” Sub-Commission.
During an examination of the available literature, some 190 apparentIy relevant articles wereidentified in “Chemicai Abstracts” for the period 1967-1991. It is interesting to note that amore detailed examination showed that 60 of these articles covered not only topics relevantto kiln operation, the environment and associated laboratory tests, but also:
l the production of mineral&d clinkers (despite efforts to exclude this topicfrom the list)
a low temperature clinkering by chloride addition
l the cement/sulfuric acid process
0 the use of waste materials in kiln feed.
65% of these articles came from. Eastern Europe, suggesting that there may be a knowledgebase in the countries formerly behind the Iron Curtain. These subjects remind us that volatilecomponents are nor merely bad news for cement producers, but may have useful effects onproduct performance and on economics in certain circumstances.
2 . VOLATI-LES: WHAT ARE THEY AND WHAT ARE THE MECHANISIMS OFVOLATILISATION?
The concern is with elements or compounds which partially or entirely evaporate in the kilnand which are transported towards cooler zones in kiln gases. Some can escape via the stackor are trapped in precipitator dust. Others condense as they leave the kiln and/or react withor condense on the feed in the preheater system.
The principal volatile elements are : K, Na, Cl, S, Pb, TI, Cd, V, Hg, Zn and As. Theelements F, V and As can be classed as “moderately volatile” and the others as“significantly”.
They originate from inorganic and organic compounds in raw materials and fuel. In the caseof raw materials, certain compounds can readily volatilise at a temperature below 600 deg.C, especially mercury, thallium and sulfur (if present as sulfide or in organic combination),but in generai volatile compounds in raw materials only evaporate pat-My as the feed passesalong the kiln system and through the burning zone.. -The residue will be retained in theproduct, either in solid solution in the principal ‘phases of the clinker or as discrete
compounds - normally alkali chiorides and sulfates. T’ne typical proponions of volatiles inraw materials which evaporate while the feed passes through the !tiIn system are as foIIows(“primary volatiliries”, according to certain writers):
c/oso3 6 0 - 9 0K2O 30 - 70
NazO 20 - 40Cl, Hg 96 - 9 9
F 1 0 - 40Pb, n 6 0 - 9 9
C d , V, Zn IO - 20
In contrast, fuei voiatiles are almost always entirely evaporated during combustion.
Evaporated volatiles travel back up the kiln in the gas phase where:
i> they condense on the feed and form the basis of a recirculating volatile loadin the kiln system
ii) or they condense as a fine dust or fume which is finally trapped in theprecipitator and which wiI1 then become part of an external volatile cycle ifdust is partly or wholly returned to the kiln system
iii) or they condense on a colder surface in the kiln system and form the basis ofa build-up
iv) or they escape through the stack either in the gas or vapour phase or as a finefume.
The remainder of this text concentrates on the cycles of minor elements (Cl, K, Na, S)originating in the burning zone. The cycles of trace eiements and/or cyIess hot parts of the system are not examined in detail.
When volatiles condense on raw meal and are returned towards the burning zone, dependingon the overall chemical conditions and burning conditions, they form a range of volatilecompounds which themselves evaporate partially and are partly retained in the clinker - eitheras discrete compounds or in solid solution in the clinker phases.
In general, chloride preferentially forms potassium chloride (KCl) and only when there is anexcess of chloride over the needs for chemical combination with the available potassium willsodium chloride (NaCl) be formed as a recirculating volatile species.
A large part of the alkalis and sulfate entering the burning zone is in practice present in theform of molten sulfates, forming a separate Iiquid phase immiscibIe with the principal ferriteflux.
2
The typical proportions of voiatiie compounds which evaporate in the burning zone (in theabsence of reducing conditions) are as follows:
%K,SOq 40 - 60
NaiSO? 40 - 602CaSO,.K$O, 40 - 100
K,O in solid solution 60 - 90NaZO in solid solution 20 - 40
K C 1 97 - 99NaCl 96 - 99
CaSO, 80-100
In consequence, a cycle of recirculating volatiles develops, which only finds an equilibriumwhen the total quantity leaving the system (in clinker, dust and stack Iosses) equals thatentering the system (in raw materiais and fuel). Various tables and figures are appended,showing melting and boiling points and vapour pressures.
At this point the level of volatiles in recirculation can be significantly greater than the totalmte of introduction of volatiles. The volatiles in the vapour phase can be in various statesof dissociation and recombination. Alkali sulfates evaporate congruently, that is to say thatthey disappear entirely when heated for a long period, whilst &SO, decomposes and leavesresiduaI CaO (in oxidising conditions). CaO:CaS03 melts can form. Typical recirculatingvolatile loads expressed as % of the total quantity introduced are as follows:
ChlorideK2O
Na,Oso3
%
5ooiJ200 - 650150 - 200200-800
The effect which these recirculating volatiles exert on the formation of build-ups at the kiln(gas) exit depends on the composition (which governs the temperature of liquid formation andthus the position and hardness of the build-up) and on the quantity (which governs the rateof formation). The dependence on vapour pressure on temperature differs for various speciesand the “relative volatility” (or rank order of volatility) can vary in the cold and hot zonesof the kiln system.
In the past, several empirical limits have been proposed for the concentrations of volatilesadmissible in a kiln, e.g., 0.03% Cl on clinker for preheater kilns. Today there is atendency to prefer to specify concentrations tolerable at the kiln inlet (in hot kiln feed at zeroloss on ignition). By way of indication, the concentrations of volatiles which can be toleratedin the lower stages of a preheater are typically given in the following ranges (exceptionsbeing of special interest for study):
5%Cl 1.2 - 1.8
so3 2.5 - 4.5Alkalis (eq. Na,O) 2.5.- 3.5
3
The FL.5 encrustation index
R = Total molar S inoutTotal K,O input + 0.5 (Total NazO input)
can be used as an indicator of the potential nature of any build-up, as follows:
R31 Hard build-ups based on SO,0.7 < R < 0.9 Relatively soft build-ups (easily removed)
R < 0.5 Carbonate-based build-ups in due course.
Most suIfates condense in the range 9000 - 1100 deg. C. The presence of fluorine canaggravate build-up problems due to the formation of fluoride compounds and. their aid to theformation of various silicates.
Potassium chloride alone condenses between 800 and 900 deg. C (and sodium chloride at aslightly lower temperature). Build-ups can develop in the kiln feed chute or in the riser ducttowards the bottom stage of the preheater.
There is an optimum temperature for the capture of SO, by a freshly cakined raw meal(e.g., 880 deg. C in one study). Primary condensation is expected to be in the form of liquidalkali sulfates. It is often interesting to calculate the composition of the sulfate phase in kilninlet material, with its addition of KCl. Fusion in the system Na,SO,/ K$O,/ CaSOJ KC1begins at below 700 deg. C. Liquid films on dust particles are The origin of build-ups andas the thickness increases, internal temperature drops and new equilibria may be establishedand compounds formed.
There is less literature on the phenomena governing condensation than on evaporation. Theeffects of atmosphere and the implications of precalciner operation are perhaps worthy ofstudy, especially for sulfate compounds which can be present in various states of oxidationand which can react with water vapour to form bisultites and bisulfates. The characteristicsare as follows:
ChemicalState
Fuel and raw material Clinker Vapour
Oxidiseds4+, 9’
Sulfares, e.g.,gypsum, anhydrite,alum, etc.
Alkali sulfatesand aBali/alkalimetal sulfites
SO2 and (atlow temp.)so3
Neutral, S Elemental S
Reduced,S2-
Pyrites, marcasiteorganic sulfides
Oldhamite, CaS,complex suiftdes ofcalcium, aluminium, etc
Non-volatiie
The oxidised sulfur cycle is illustrated among the appended figures.
3 . CYCLIC NATURE OF VOLATILES N JSXN SYSTE-MS
3.1 EFFECTS OF VOLATILE CYCLES
The volatilisation and condensation of volatiles in a kiln produce two undesirable effects onthe kiln process:
l the formation of build-ups - possibly blockages and the possible emission ofSO, from the system
a transfer of heat away from the burning zone towards cooler parts of thesystem.
There are also effects on the clinker, which may be summarised as fofollows:
Fluxing action:a lower temperature of first liquid phase formationl change of liquid viscosityl alteration of surface tension of liquid0 modification of crystal morphology.
5
Phase re!arions:0 the relative thermodynamic stabilities of the clinker minerals can be altered by
solid solution effects.
Hydraulic activity:0 the reactivities of the clinker minerals are altered by solid solution and/or by
the effects of crystal symmetry (high temperature stabilisation of polymorphs)and/or effects occurring during hydration (e.g., coating of cement particles byinsolubie salts).
(It is difficult to isolate these three classes of effect in practice.)
3.2 WET AND (LONG) SEMI-WET PROCESS
There is an obvious external cycie (dust return) as well as an internal cycle which has,perhaps, received less attention in the literature.
In an example involving a coal with a sulfur content of 4.5% (not very differ&t from thelevel for a blend of coal and sulfur-rich petroleum coke), there was a high internal cycle andsignificant stack losses. In one BCI kiln these represented 42% of the quantity introducedto the system and were 5 times higher than the proposed BATNEEC concentration.
Typically, FLS expect 30% or more of the sulfur entering a wet process kiln to escape viathe stack. The external cycle can be influenced by the proportions of dust returned to thesystem by various routes.
3.3 LEPOL PROCESS
The volatile cycle is more complicated on account of the additional external cycles due todust from riddlings and cyclones, even though the basic situation seems similar to that forwet process kilns. However, there is a major opportunity for a volatile bleed (especiallySO,) by disposing of riddlings and cyclone dust as well as that from precipitators.
3.4 DRY PROCESS
As indicated above there are both internal and external volatiIe cycles.
In general, sulfur escaping the preheater is found in the form of dust rather than SQ andforms part of the external cycle involving the raw mill, conditioning tower and precipitator.Further, it is expected that SO2 in the gas phase will be absorbed in the lower stages of thepreheater, at least if there are no adverse conditions (e.g., chemically reducing conditions).
When sulfide is present in the feed, a significant fraction will be lost from the preheater asSO, (e.g., 30 - 50%) and partly absorbed in the raw mill and the precipitator system.
6
4. CHAtYGES N P R O C E S S CO?iDITIONS rvHICH C&Y INFLUEYCEBEfIAVIOLJR OF VOL;ITILES
4.1 PAJiUMETERS NFLUENCNG VOLATILE RECIRCULATION
The principal parameters which influence volatile behaviour are as follows:
temperaturetimetype/compositionconcentrationdiffusion towards the solid surface (as controlled by clinker nodule size andflux content and composition)gas/solid contactother reactionskiln atmosphere (laboratory tests suggest that water vapour plays a role, aswell as the “traditional” kiln gas components).
(For summary, see table among appended figures.)
Once a kiln is in operation, the main parameters available for the kiln operator toalter/control are th.e temperature and the atmosphere in the kiln. The rate of gas flow seemsto be of secondary importance. Process design and local chemical conditions also play apart, determining the total quantities introduced to the system, chloride content, relativeconcentrations, combinability, fuel and to the firing system parameters and mixing withinthe clinker bed (with exposure of nodules to gas flow at the surface).
It is often difficult to distinguish chicken from egg in the industrial operation of a kiln. Forexample, when CBR changed from gas (or indeed, to 92s) as a fuel in Canada in the past,there were effects on volatile cycles. This is to be expected due to the presence of a higherlevel of water vapour in the combustion products (e.g., coke < 5 % , lignite > 10%) and thehigher vapour pressures of alkali hydroxides (see attached figures), but such changes arealways accompanied by other alterations to the quantity and composition of volatilesintroduced and/or the raw meal chemistry. The effect of nodule size on volatile behaviourseems equally. impossible to separate from that of the effects of liquid from alkali melts onclinker size grading (as discussed in past CETIC work).
It is important to note that, in general, no-one measures “typical” volatile balances (saveglobally): available detailed balances are usually gained when there is a need to investigatea non-typical kiln system due to some problem or another. A number of illustrations follow,taken from the experiences of participants in the CETIC Group.
4 . 2 ITALCEIHENTI
When CaC12 was introduced via the flame (0.3% on clinker) to volatilise K,O in a Gepolpreheater kiln of 2000 t/d capacity (Stockertown, USA), it was noted that operation couldcontinue for many hours with kiln entry levels of Cl of,around 3% with somewhat reduced_-
7
loss on ignition (heat pump effect). This indicates the capacity of this type of preheater totolerate a little more Cl than cyclone preheaters (although long term results from Stockertownare still awaited).
4 .3 CBR
With chloride injection on a precalciner system (with bypass), there was a marked effect onCl and alkali levels in kiIn inlet material but not on sulfate. (The same was true atStockertown.) Full system equilibrium was not reached for three days. At another Works(about 60% heat energy input at the precalciner and no bypass), an upper sulfate limit on kilninlet material of 3% was established in order to avoid any build-up problems (althoughperhaps not corrosion problems!). In this latter case the sulfate level was lower in thepresence of chlorine and of potassium (see later data); at the same time there was also acertain reduction in SO, loss from pyritic material in the preheater. It is known that thisprecalciner rapidly forms build-ups above about 91.5 deg. C. In a wet process kiln, theformation of rings can be followed with the she&scanner and the flame setting altered toeliminate them (provided that action is taken within 2 to 3 hours).
At Lixhe, various phenomena were noted when returning to coal firing after the use of gas,including a reduction in sulfate cycles and in the level of decarbonation at the preheater towerexit. This latter phenomenon results from a lower heat release within the preheater, notablyfrom CaS04 recombination. The thermal effect is of the order of 75 kcal/kg with the inverseeffect in the burning zone. Blue Circle have calculated the magnitude of this effect as 109kg/kcal at Hope Works in the past. At Lixhe (dry process) the sulfate level in the kiln entrymaterial can be reduced (and that of chloride raised) by increased burner momentum: wearof the burner tip allows the level to rise again in due course. A “non-stick” kiln feed chutelining from Hasle also gives good results.
Also at Lixhe, a number of interesting relationships have been established from the resultsof three years’ operation (with analysis for volatiles in kiln inlet material twice per shift).For example:
No. of kiln srops per monsh = -5.3 f 2.7 x %S03 (in hot meal)for cyclone blockages)
I?* = 0.88
%S03 (in hor meal). = 4.8 - 0.36 x % K,O (in hor meal) R’ = 0.68
It was noted that the input of used tyres at the kiln back end gave good results in mechanicalremoval of build-ups.
4.4 LAFARGE
A compilation of volatilisation levels was made in 1985 for all company kilns. Thecompany’s calculation of “volatility“ is somewhat different from that often encounteredelsewhere. The following results (which have changed little since that time) wereobtained:
8
%so3 K2O
Na,O
I-w 56 34 14
Dry 80 6 9 2 6
Precalciner 55 49 5 5
(Retention levels are close to 100 % for preheater kilns and at lower levels for the otherprocesses, being related to the level of dust disposal.) If is noted that Lepol (and wet)process kilns give Iower volatilisation levels than preheater kilns and that precalcinafionseems to influence these phenomena. Nevertheless, due to the small quantities of dustinvolved, the enrichment of volatiles in precipitator dust is highest for the Lepol process.(Italcementi note that for balances determined on 23 kilns the enrichment factor for dustcompared with raw material is close to one for SO,, K,O and NazO in the dry process, butbetween 9 and 11 for the Lepol; in the case of chloride the comparison is between a factorof 8 for the dry process and 123 for the Lepol; the values for long, granule-fed semi-drykilns are intermediate.)
In examining the performance of a new low-NO, burner with a higher momentum than theprevious one, it was noted that the CO signal could be made to disappear (for the same C+level) with less decarbonation at the preheater exit and a higher level of kiln drive power(Amps). These effects were accompanied by an apparently higher BZT (with less clinkerfree-lime), less gaseous SO2 at the kiln exit, and kiln inlet material with less SO, and ahigher loss on ignition at 1000 deg. C.
4.5 OBOURG
Here the clinker KzO level is used as a control parameter for the wet process tiln and aconsiderable data-bank of measurements has beeri built up. At the end of 1990 the use ofa lower ash fuel began and the clinker K,O level dropped from 0.69% (1990 mean) to 0.55%(mean for January/February 1991), despite the introduction of a little more potassium to thesystem (equivalent to. 1.43 % on clinker instead of 1.34%). Evidently the dust - returned tothe kiln - had become more rich in alkalis. It can be shown that the proportion of $0brought in by the solid fuel fell from 24% to 17.5% while at the same time that brought inby the dust return rose from 18.5% to 29 %. This observation leads to the conclusion that$0 incorporation in clinker does not only depend on the quantity introduced but also - andabove ail else - on the type of material which brings it in and perhaps on the position whereit is injected. On screening the clinker at 20 mm the same chemical analysis was found foreach fraction with the exception of K,O, where the concentration was about 10% higher inthe coarse fraction.
Here the clinker alkali content has successfully been reduced by chloride addition at theflame. Ciments Franc$s have also demonstrated this effect with CaC12 addition to slurry(3.5% K,O in the dust in comparison with 2.7%). Blue Circle also once succeeded indemonstrating the efficacity of this method (accompanied by non-return of part of the dust)
9
in lowering clinker K,O ieveis by a half in a long kiln, despite the fact that some questionsremained about the most appropriate place to introduce the chloride; it must be noted thatthere can be problems with the flow behaviour of precipitator dust above a certain chioridelevel.
4 . 6 CIivIENTS FRANCAIS
On adding precalcination to a Lepol grate with (stoichiometrically) more sulfur than alkalisin the system, an increase was noted in sulfate and alkali levels at the grate and especiallyin the dust and nodules beneath the grate. More potassium sulfate was found in the clinkerwith precalcination; CaSO, was found in the cyclone dust and somewhat less in theprecipitator dust, arising from kiln dust which had travelled across the layer of nodules onthe grate. There was a little more SO2 emission with precalcination. On another Lepol kilnno such effects had been found on adding precalcination; at Frangey, Lafarge had noted asomewhat higher recycle of potassium and sulfates with Lepol precalcination. (At this latterWorks, with use of chloride-rich substitute fuels, it is found necessary to carry out samplingover periods of at least a week to determine consistent volatile balances.)
To use a high chloride coal (-0.15% Cl) on the dry process it has been found necessary toprepare a mix with another coal to avoid build-ups with typically 2% Cl at the bottom ofcyclone 4. Analysis of build-ups along the kiln indicated that chloride levels reached 30%(at zero loss on ignition) in the coating from the base of cycione 2 and 20% at 50m into thekiln (despite its less than 5% level in both hot and cold parts of the kiln); run-out of materialfrom a stopped kiln gave chloride levels rising up to 0.7%.
During a past experimental campaign of burning chlorinated wastes, it was noted that thesimultaneous presence of chloride and sulfate at high levels could give rise to emissions ofHCI and SOz. Apart from this, the volatiles were all assimilated in the c!inker (burned atlow temperature with free lime levels of up to some 13% and formation of CaCI,.C,S) orin the dust (and probably also trapped in refractories).
4.7 ENCI
After the addition of a second stage to the preheater, various build-up problems wereencountered. In 1985/6 the kiln exit 0, level was increased from 0.5 to 1.5%, the solid fuelresidue at 90 microns was reduced to below 25 % and several “Cardox” units were installed.These actions improved the situation and in 1987 20m of “Magotteaux” stirrers wereinstalled, the burner air velocity was increased to 100 m/s and a Hasle “non-stick” lining wasinstalled in the duct and cyclone dip-tubes. These efforts made an output rate of some 110t/h possible without build-up problems.
More recently petroleum coke (3.5% S) has been fired (first at 4.5 t/h and afterwards 6.5t/h), accompanied by oxygen addition at the flame and, finally, by the use of slag (S - 1%)as a raw mix component (5%, and then 10%) with yet more coke (8.0 to 8.5 t/h, i.e.,- 60% of fossil fuel energy). At the start of 1991 the production rate was 120 t/haccompanied by preheater blockage problems. During ,199l it was deduced that problemsr
10
with build-ups could be avoided if the SO, level in the kiln entry material was kept beiow2.5%. This was possible with a coke input rate of about 8 t/h and a slag level of 10%provided the oxygen level at the kiln back end was kept consistently at 2%. If theseconditions are not met, then kiln operation rapidly runs into problems. The “Fuzzy Logic”control system helps to achieve success, as the 0, signal standard deviation has fallen from0.45% to 0.25% and that for the SO, in hot kiln-feed from 0.6% to 0.2%.
4 . 8 HOLDERBAhX
In the past, Iaboratory data have been gathered on minor elements and these confirm theeffects that are now more widely known. For example, suIfur volatility in a standard regime(70% Nz, 30% CO) is close to 100% at 0% 0, but falls in the presence of 0,; neverthelessthe effect of O2 is much less at 1400 deg. C than at 1200 deg. C. The volatility of minorelements in the laboratory is also much greater for powdered material than for granules.(See appended illustrations, taken from external literature.) Currently there is interest in rawmeal morphology and in the distribution of volatiles in the meal at the start of clinkering.
A precalciner kiln system in Spain ran for many years with a Cl level in the kiln entrymaterial between 3 and 4 % (that is to say about 0.5 % less than K20) and with no trace ofCO. In this case there was about 1.1% SO, in the kiln entry meai and 4% K,O and noproblems, but if CO was present there was about 2% SO, and 5% I(,0 in the hot kiln feedaccompanied by Spur&e-based build-ups and cubic KC1 crystals. (It is also recognised inCiments Franc@ that regular kiln operation helps to minimise the phenomenon ofcementation by the freezing/thawing of chloride-based deposits.)
While burning wastes at Clarkesville (wet process), it is found necessary to ensure that theclinker Cl content is always kept below 0.3 %, otherwise the kiln becomes unstable. AtOrigny there have been an enormous number of kiln stops caused by preheater blockageswhich, when sampled, do not contain many volatiles. This effect seems to have its originin a liquid phase formed by calcite arising from a chalk with an extreme level of finenesswhich can decarbonate and recarbonate very rapidly. The problems have been much reducedby altered cyclone geometry and helped a little by the use of a mechanical cleaning device.
4.9 BLUE CIRCLE
On one precalciner kiln it is difficult to find “typical” volatilities. For every determinationthere are almost always different values (40% for SO, and 50% for K,O changed to 25%and 4O%, for example). One can imagine that this is caused by variations in the nature ofthe raw materials and the content in the kiln feed of sulfate (and sulfite) captured in the mealafter initial low temperature voiatilisation in the preheater.
In order to examine the possibility of producing a sulfate-rich clinker (2% SC&) using certainavailable resemes of material and without installation of a by-pass on a new kiln, rests werecarried out for about three weeks on a dry process kiln at another site (-35 t/h). Theobjective was to reduce the volatilisation in the burning zone by playing on processparameters and producing a lightly mineral&d clinker (-- 1% K,O, -0.15% NazO, and
1 1
- 0.15 % F, as usual at that Works, but with double the usual level of sulfate) and with asilica ratio a litT.ie lower than usual (-2.7 instead of -3.2), accompanied by a change inalumina ratio from 2.8 to 2.2. During the changeover there was some tendency to form softbuild-ups in the preheater, but with the new regime established these moved towards the kilnfeed chute without causing any major problems for kiln operation. The apparent burningzone temperature was reduced from about 1500 deg. C to 1380 deg. C, while K20 volatilitydropped from 70% to 60% in the burning zone and that of Sq from 80% towards the range50% to 60% provided that kiln exit oxygen level was kept above 2%. There wereimprovements in the output and fuel consumption of the kiln and, in fact, the experimentalWorks adopted certain of these changes during its normal operation for several years, untilthe asrival of demand for low alkali clinker.
At Hope Works (dry process), tests were carried out involving various NO, levels as wellas reducing conditions.
so, : The ratio of SO3 in Stage IV to Scl, in raw meal variedtypically from 1.8 to 2.7 for the higher levels of NO, and was3.0 for a low 0, level. The clinker SO, content fell.
KzO and NazO : In a parallel manner, for K,O the ratio of the content in StageIV to that in raw meal varied from 3.8 to 4.4 and for NazOfrom 1.6 to 2.0.
In general, reducing conditions increase SO, level. at Stage IV by a factor of 2, giving alower clinker SO,.
As already described in a paper to the CETIC Technical Commission, at Cauldon Works(and later in other dry process Works) SO, has been monitored at the kiln back end todetermine the local rules for avoiding blockage tendencies. The SO, signal is noisy anddifficult to interpret without a knowledge of the history of the system, e.g., a reCent fall ofsulfate build-up material arriving in the burning zone can give rise to a high SO, signal atthe kiln back end despite the presence of a good flame and acceptable levels of volatiles inthe kiln entry material. At Dunbar there has been success in reducing the number of kilnstops per year caused by preheater blockage from over 90 (1987) to less than 10 (1989), losttime hours having also fallen from around 450 per year to about a hundred. (There werealso major gains in stops caused by rings and breakaways at the kiln entry seal.) There isno need to keep such monitoring equipment in permanent operation once the rules areestablished, but it expected that renewed investigations will be needed each time theconditions of operation change. In practice it is now found that with this know-how sulfur-rich petroleum coke can be used (to a certain level) even on dry process kilns which in thepast have given problems with just coal firing - but in several cases the build-ups seem tohave moved from the preheater into the kiln (where they are destroyed). In a general mannerit can be supposed that there are problems of both short-term and long-term and stability:once a stable burning zone volatilisation is established, one must wait for stable conditionsto arrive higher up the system and in the large masses of material which form the build-upsand coatings already in existence.
1 2
During tests of SO, monitors at the exit of a long kiln with filter cake feed, it was noted thatthe signal usually remained stable (below 100 vpm). But, when the oxygen level fell therewas an inverse correlation between the 0, and SO, signals. In this case levels of around1000 vpm SO, were reached, with considerable variations; it is supposed that cycles movedfurther up the kiln (nearer to the analyser) during low oxygen periods.
At Plymstock Works (dry process), when changing the BZT from 1390 to 1500 deg. C theratio of SO, in the fourth stage to that in the raw feed rose from 1.2 to over 4.0. Similarresults were obtained ‘at Lichtenburg Works (South Africa).
It is noted that a better understanding of volatile recirculation is useful for kiln operationbecause back end oxygen indicators can sometimes be misleading.
At Mason’s Works (wet process), raising the 0, level gave higher levels of SO, and K20retention in clinker (concentrations rising from 0.18 to 0.54% SO, and from 0.33 to 0.80%K20). Also for the wet process (Westbury Works):
Kiln 1, “low momentum” flame,2 % 0, - 2500 mg/Nm3 at kiln exit.
Kiln 2, “good momentum” flame,2 % 0, - 2 5 0 mg/Nm3 SO, at kiln exit1 % 0 , - 1350 mg/Nm3 SO, at kiln exit.
In practice alkalis are controlled on the wet process (by means of the LINKman system):
Masons: % alkali target
< 0.550.55 - 0.7
> 0.7
NO, set-point@pm at precip.)
5 5 04OO-500
300
Ravena (USA):- alkalis controlled by NO, set-point- sulfate/alkali ratio controlled by 0, set-point.
5. EFFECTS ON CXANKER
Sulfate retention: In general, changin,0 from a situation with excess alkalis offersadvantages.
In general, a higher SO, content:improves early strengthimproves workabilityproduces a more difficult “apparent grindability”.
Increased ciinker alkali levels can also be associated with sulfate retention for Lepoi and wetprocess kicilns, especially if there is already an excess alkali content.
13
The effects of minor components on the viscosity and surface tension of liquid phases canbe complex. Lower viscosities encourage alire formation. Calcium sulfate flux can,however, stabilise belite and/or cause the production of clinker alite with lime inclusions.(Sulfate liquid systems are capable of influencing ionic transport and chemical combinationdespite the limited solubility of the principal clinker compounds.)
In clinkers with a low al*ka.li content, there is the possibihty of belite stabilisation (difficulicombinability) due to excess SO,.
Reducing conditions: Reducing conditions in the burning zone can give a cement with poorflow characteristics (due to free K,O and NazO), poor workability (due to the increasedcontent of C3A and its reactivity), poor strength (lower C,S content) and variable colour.
Fundamental aspects: At some future date, the production of lower LSF and/or mineral&dclinkers may be of interest.
Alkalis retained in clinker are present either as stable sulfates or absorbed in the silicate andaluminate structures. NazO has a more marked tendency than K,O to form solutions in CIA.For ciinkers with (molar) ratios of sulfate:total alkalis below 0.5, almost all the sulfate iscombined in water soluble form, K$O, being predominant. A proportion of the alkalis arein solid solution in the clinker C,A and this has an adverse effect on the initial cementreactivity and thus on concrete and mortar rheology.
For ratios between 0.5 and 1.0, a certain quantity of langbeinite (2CaSO,.K$OJ is alsoformed (and not all the alkalis are soluble). For ratios above 1.0, significant fractions of thesulfates are combined within the sihcates and aluminates or as anhydrite (CaSOJ, whichdissolves more slowly than alkali sulfates, whilst the fractions of KzO and Na,O which aresoluble in water approach 1.0 and OS, respectively, at a ratio of about 1.5. At sulfate:alkaiiratios above 1.5 trends are somewhat erratic. For most normal clinkers the principal sulfatephase will be aphitalite with a maximum WNa ratio of 3.0. This phase is accompanied byminor quantities of K-$0, and calcium langbeinite, Na,S04 being found only for unusuallylow WNa ratios.
As well as the solid soiution effects and the formation of compounds described above,various permutationsof volatiies (especially in the presence of fluorine) ‘can influence thestmcture of alite and belite crystals. (A comprehensive review of recent work forms part ofthe text of G K Moir and F P Glasser at the 1992 International Congress on CementChemistry in New Delhi.)
6 . TOWARDS A MODEL OF VOLATILE CYCLES
Various empirical volatility factors have been proposed and used with a certain measure ofsuccess. This section considers the possible approaches to a more fundamentally basedmodel.
It is generally supposed that (other factors being equal) the extent of voiatilisation decreasesas the thermal efficiency of the kiln increases. An explanation may lie in the fact that this
14
is due to the limiting effect of vapour saturation by al,kaIi compounds. Studies by 3lue CircIeof the treatment of kiln dust in a 100 mm diameter fluidised bed tend to confirm thishypothesis.
This study examined the feasibility of producing a low quality clinker from flue dust withcapture of the alkalis distilled from the bed (for possible use in the fertiliser industry).Saturated vapour pressures at 1200 deg. C are (for the pure substances):
KC1 0.18 atmK2SO4 0.8 x 1O-3 am
(0.6 x 10m3 atm with decomposition suppressed)Na,SO, 0.13 x lo3 atm
(0.01 x 10s3 atm with decomposition suppressed)
The transport capacity of air for vapcur at 1200 deg. C is thus
KC1 700 g/gK2S04 4 g/g
Na2S04 x0.5 g/g
(The capacity at 1250 deg. C is about two times higher).
It can therefore be foreseen that (unless the equilibrium vapour pressures differ greatly fromsaturated values) there will be little problem in removing KC1 from many kiln flue dusts ina fluidised bed with a gas flow rate of, say, 2 g per gramme of dust, although the capacityfor sulfate removal may be limited.
(A wet process kiln typically operates with a ratio of a little less than 2 g/g gas/soiids in theburning zone and perhaps 2.75 g/g at the back end; the corresponding values for the dryprocess are 1.4 g/g and 1.94 g/g).
It is suggested that
V” = (I’*) (M,L_(P - p*) c-q
v* = saturated vapour concentration in transport gases (kg/kg)p* = saturated vapour pressure )
of an alkali compound ) same unitsP = gas pressure >M, = moIecuIar weight of vapourM, = molecular weight of gas.
Given mathematical expressions for saturated vapour pressure as a function of temperatureand knowledge of the temperature profile in the kiln system, the saturated vapourconcentration can be calculated for each alkali compound and thus the maximum quantitiesevaporated from the feed per unit mass of gases. In considering the amounts of gas passing
15
through the kiln at vaiou~ temperatures, the true quantity of volatiles transported per unitmass of clinker can thus be calculated and from this knowledge, “ideal” volatile cycles canbe deduced. (It is to be noted that, paradoxically, when alkali addition allows BZT to bereduced then blockage probIems can be lessened due to the dominance of temperature in theevaporation mechanism).
Despite the fact that qualitative differences between two kilns (one dry process and one wet)are reflected in sample calculations, such “ideal” calculated recirculating loads are about 10times larger than those encountered in practice. The probable reaSons are:
Incomplete contact between gases and solids in the kiln, where only a smallfraction of the solid surface is exposed at a given time. (It is expected thatthere is better contact in the colder dusty regions of the system.)
b) Volatilisation characteristics of the alkali-containing minerals at a given plant.(Alkalis seem to be lost more e&y from silicates and aluminates than whenpresent as sulfates).
cl TEuISpOIt Of compounds which are condensed ~/on solid dust or fume.
d) Reduction of vapour pressure over solutions of alkali compounds.
e> Inadequate treatment of the transport of heat and of vapour within the bed ofclinker nodules in the kiln.
0 Formation of other compounds, e.g., &SO,, depending on the alkaksulfateratio.
Unstable operation of production kilns, so that practical conditions are notexactly those expected for very long term stability of temperature and materialflow.
The further development of a predictive model will have to take account of such factors, aswell as the effects of.composition of kiln atmosphere. In recent years there has been muchinvestigation of factors governing the blockage of cyclones and their performance in hightemperature coal combustion processes (in the hope of protecting turbine blades in directcycle electric power generation systems).
When lime (or limestone) is injected to absorb SO,, the compounds and thermodynamiccriteria of interest in combustion systems are exactly those encountered in the cementindustry - particularly when relatively high chloride coals are used. It is probable that thereis now sufficient academic knowledge to better treat our situation and allow an improvedmodelIing and understanding. Another aspect to consider is knowledge acquired from studyof the regeneration of CaO sorbents used for SO, scrubbing: again, data potentially relevantto kiln systems are produced, for example, on pressures of SO, in the system CaSO,/ CaS/CaO in the presence of various concentrations of CO and CO, (see appended figures).
1 6
(It is interesting to note that volatile condensation has an effect on the kiln power signal usedfor process control. Any perturbation of the chemical composition of the kiln feed whichraises volatile content will increase kiln Amps; a control strategy seeking a constant Amp&resignal would have the effect of reducing burning zone temperature, yielding under-burnedclinker with a relatively high volatile content. A strategy using a constant fuel feed ratewould be equally inadequate, due to the depression of burning zone temperature producedby the increased volatile load. The best control of product quality should result from asystem based on observation of the peak clinker temperature, that is to say, indirectiy by kilnexit NO, control.)
7 . EFFECTS OF CONTXXSATION
The most probable primary condensation is in the form of liquid alkali sulfates, Melting inthe ternary system Na$SO,/ K,SO,/ CaSO, starts at below 800 deg. C. Addition of KC1increases the range of suIfate compositions which is liquid of this temperature and allowsformation of liquid melts even below 700 deg. C. Deposits on the feed can provokechemical reactions; they can equally cause adhesion and - as with deposits on surfaces -initiate build-ups. (Direct condensation as calcium langbeinite is not expected ontherrrtodynamic grounds.)
While the literature tends to agree (although not totally) on vapour pressures of pure a&licompounds, information for the more complex species of interest in cement kilns is morerare. Studies at Aberdeen University have produced self-consistent results for sulfosilicate,sulfoaluminate and langbeinite. The order of volatility alters with temperature. As indicatedearlier, liquid alkali sulfate systems have a poor dissolving power for most of the principaloxides of cement clinker. However, they have low viscosities and a low surface tensionagainst silicates and thus cover and englobe these particles very effectively. It seems likelythat the small quantity of silicate which is dissolved has a high mobility, so that the liquidsare effective at producing a reaction (for preference towards C2S at 700 to 800 deg. C.).Stabiiisation of carbonates has been suggested (CaCO, can dissolve in the liquid phase in thepresence of alkali sulfates in the range 880 - 900 deg. C., forming a liquid rich in CQ andthe presence of fluoride can cause further complications - but equally (in combination withcertain concentrations of other compounds) certain advantages as far as clinker quality isconcerned.
C P KERTON
June 1992 (English version, December 1992).
)jats~c;ld w D, Trans. hwhy Svc.. 66 (81, I966 - 1973. (197W.
rcrry R 11 & Chil!on C II, Chemical Engineer’s tlandlmk, McGraw-Ililt,
New York (S\h cJi\ion 1973).
Temperature (deg. C
/
~r3pt-1 to confirm that proportion volatilised for 5oiven hating regime is dm-xteristic of raw mix
(i.e., (fiat volatilisation reacfion is first order with rap+% to alkali content).
ha from Palmer K & Bayik 0, pc~ R. epon M-117(1952] ud from W&J H. Rock ProdUCu 45 (2j.M - 68 (19413
/II
iIIf
i
I350 -
Temperature (deg. Cl
MeI tinq point (“C)
ea -c 8 0 0
ca 440-#SO
edso-904
m9ou-954
CID 7 954
Meltinn &ae of (a) the CaSO4-wic SO -NazS04 System
and (b) the Effect of 6 KC1
(From fue .air---c------ ,wpp- ------4~p--
.
Oxidized P o r t i o n o f t h e S C y c l e R e l a t i v e t o t h e Ki ln .Dot ted pa ths r epresent c i r cu la t i on in the vapour phase ,solid l i n e s i n t h e s o l i d p h a s e ( s ) .
SLJAlAl,~l~Y 01: 1~AC’I’O1ci \\‘IIICII INi~LUi:NC~ ‘IIll!IIl~l~VIOU1~O1~~lLNOI~VOLA'I'IL~COMI~UNDS1N1WaN SYSTEMS
1.
2 .
3 .
4 .
5 .
6 .
7 .
8.
9.
LO.
11.
12,
Burning zone temperalure(alkali vapour pressures) - level
- variations
Temperature profile of burning zone
Comp&ition of alkali liquid systems in theburning zone
Atmosphere in burning zoneglobally reducinglocally reducingwater vapour
Clinker size grading ’
Clinker llux content (density)
Thermal efficiency (gas flow rates)
Prehea’ter system designverticalcold areas/air inleaksanti-build-up lininggeometrysolid/gas loading
Precalciner: designoperation
Composition of alkali phase in prehealer
Dust return
By-pass system
MAJOR SECONDAItY I’OSSll3LE CONTICOLINFLUENCE INFLUENCE ACTIONS
00
:
0
0
0
0
0
0
:0
0
0
Soft burning (including fluxes and mineralisers).Controlled burning.
Flame/burner settings.Fuel Characteristics.
Selection of raw feed chemistry(sulfate/alkali ratio).
000
0
0
00
0
Burner/flame settings.Fuel characteristics.Coal/coke fineness.Choice of fuel (solid, liquid, gas).
Selection of raw feed chemistry(sulfate/alkali ratio) - including flux.
As above.
Process design/seleclion,
Process design/selection.Elimination of air inleaks / Insulation.Design.Type of precalciner.Throughput.
Selection of precalciner.Control of precalciner.
Selection of raw mix components.Selective quarryinglbcneficiation,
ConHol.
Add.
0 = rrrrcertoin
X Drnper 1, PCA Rcjwt MRS.68 (19.54).
0 Gtrr C B Kcil I:, ‘I’IZ (4). 7 _ 9 (I9Mj).
HOURS LOST!xo
4 0 0
300
2 0 0
100
0
DUNBAR-HOURSLOST
NO. OF STOPS
. _
PREHEATER BLOCKAGES RINGS/KIN INLET BUILD-UP
1 9 8 7 1988 1989
100
80
6 0
4 0
2 0
0
DUNBAR-KILNSTOPS
PREHEATER .BLOCKAGES RINGSMILN INLET BUILD-UP
C2K53
l C
Log plot of the total pressure, in atmospheres,of rhe decomposition products of various
sulphates occurring in the cement kiln.Abbreviations:
C A s= 3Cail 0 .CaSOC5S,S = 2Ca Si0&aS04
&$33 = 2CaS&k2S044
Choi G-S & Ckser F P. Cement & Ccmxete Research 18. 367 - 374 (1988).
Phase diagram at atmospheric pressure for the systemcontaining the solids CaSO,, CaO and CaS, as well usthe gases SO,, CO and CO,. The reducing potenti equalsp(CO)lp(COJ. Region A is where Cu# and CuSO,are the only solids; region B Fras &SO, repkced by CaS(see text). Contours of equd p(SOJ are shown.c
ayhurst A N & Tder R F, I Inst. Energy 64. 212 - 229 (fgg1).
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 3
Investigation into Potential LowTemperature Volatilization
INVSSTICATION IN'@3 PV!ZNTIAL LOW TFXPEXATUEE VOUTILISATIOH
WITEIBT?BP~O&B3D OxFo3DH!.3wOKgSKIL9, PBSCALCINEB
AHDPREHUTERS-fSPERS
Objectives
1) To identify potential lov temperature volatile compounds in the rawmaterials of the'new Oxford Works,
2) To assess the quantities of volatile8 present ia the gas and Baterialstreams at partiizular positions vitbin the system, in particular vithinthe preheater and precalciner sreas.
3) To establish whether these calculated values will affect the conolusionson the size of bypass required for the nev Oxford Works.
The rav materials for the proposesnd sulphates (up to 1.546 So3 and
,xford Works are fairly rich in alkalis,% 820). A bypass has been proposed l ti
bleed off a proportion of the kiln'& to prevent these alkalis and sulphatescausing problems in clinker quality and build up vithin the preheater andprecalciner, The design of this bypass has been discussed extensively in thetechnical note STH 41/73. This note covered almost all possible condition8which could affect the design of the bypass. flowever one area of uncertaintyhighlighted by SlY gl/lj vns the possibility of significant raw materialvolatility (;,3C%) at low temperatures (<loooOC). Engineering B & D verecontacted as the problem was of a similar nature to the work carried out inthe investigation idto the processing of cement flue dusts.
This note applies'the theoretical prediqtions of the previous flue dnstwork together with other infonrration available fmm pubUshed literature tothe potential problem of low temperature volatilisation vithin the Oxfordpreheater/precalcin#r system.
Conclusions
1) Of the potential problem causing cornKC1 and sulphur'contaiuin& compound8p"
unds investigated (K2SO4, Ba$O4,l?a$O4 could be effectively dis
cussed a8 a low temperature volatile (see Table 1).
2) If the precalciher ia operated at normal temperstures (-SW'C) thenthe amount of Kj$SO4 in the vapour phase is insignificant. flovever at
3)
4)
S)
6)
7)
8)
9)
10)
higher teaPeratures (*- 95OOC) a significant amount (.-low4 Xgs per
Kg clinker of K2SO4 can be in the vapour phase. Tnns a high temp-erature in thi precalciner should be avoided as it vould have adetrimental effect on kiln operation.
The vast Gjoritp of K2SO4 and rJa$Oq will be in the condensed phaseon the suspended solids at the bypass position. This would mean thatbleeding gas alone at the bypass position vi11 not reduce the quantityof alkalis in the kiln system. The most effective uay of reducingalkalis would be to bleed off the dust on which the alkalis condense.
The quantity of KC1 in the precalciner for a precalciner operatingtemperature of 850 - 9ooOC is high (1-a on clinker) but this-isconsistent with the values predicted in SE7 81/13 and; F&RlIfSof normal vorks operating experience. Thik is taken into acconnt inthe bleed requiment.
The effect of sulphur is summarised Fn Table 2. This table demonetrateethat the source of sulphur, the kiln exhaust covsitlon and the presencesof other minerals determines whether the sulphur will be bled off by thebypass, recycled within the preheater, or exhausted from the stack.
If sulphur is present as calcium sulphate, or calcium sulphide tha t?ocontrolling parameters on the volatility are the gas temperature and gascomposition. Houever the effect of gas composition reduces with decreas-ing temperatare and the evolution of SO2 will not be large (7% IBX) attemperatures experienced &the kiln back end, and will notie sicpifi-cantly higher with reducing conditions than with oxidisiq conditions.
Low temperature volatilisation due to the presence of certain mineralorganic natter or iron pyrites will result in an increased SO2 emissionfrom the stack but should not have any detrimental effect on the wlphurcycle in the precalciner/preheater system.
Sulphur from the kiln fired fuel will tend to form a recirculating loadbetueen the kiln and preheater unless bled from the system via the bwss.
Sulphur from the precalciner fuel will form a recirculating load in thesame manner as sulphur from the kiln fuel. Houever this wxwt be bledfrom the system until the sulphnr has been recycled.
Approximately 9546 of the So2 in kiln and preheater gas streams will beabsorbed by the CaO in the kiln riser duct providing that the gas admaterials stream are in contact for sufficient time for an equilibriumto be reached. This time is very short due to large surface area of CaO.
Recommendationa
1) Further work should be carried out on the Oxford raw materials to estab-lish the form in which the sulphur is present in the kiln feed.
2) As the wunt of lov temperature volatilisation is dependant on theform of sulphur in the raw meal a standard method for determining rawmaterial volatility should be developed. Lf such a method were availableit could be carried out as a normal laboratory test on the raw mater!-'The information could then be used either for design information forfuture works, or as inforznation to the kiln controller to enable marefficient operation of the bypaas and kiln.
3) When the form of sulphw in the raw mterial has been established,a simulation of tjhe Oxford Works raw meal could be tried out at anexisting XI W works. (possibly Plymstock). %upling throughoutthe system would then show where, and at vhat temperature, volatilisationand condensation of alkali and sulphur containing compwnds occuza.
C O N T E X T S
Objective
Conclusions
Recomendations
1. RiTRODUCTION
2. THROREXCAL CONSIDEXATIONS
2.1 Volatiles Present in the Rack end Gas
2.2 Calculation of the Kaxidmii3 Amount of Katerial in
the Vapour Phase
3. SJLPZUR COFi’AlfJING COXF’OUXDS
3.1 Reaction of CaO and SO2
3.2 Effect of Reducing Conditions on the CaS/CaS04
Equilibrium
3.3 Effect of Iron Sulphides
3.4 Effect of Xinerals
3.5 Effect of the presence of organic sulphurC' icontaminous compounds
3.6 Effect of sulphur in the fuel
4. CONCLUSIONS
5. RECOXNENDATIONS
7) Estimated Alkali Vapour in the Kiln/Preheater
Gas per Kg of Clinker (no bypass)
2) Effect of Sulphur on Raw Material Volatility
7
7
8
8
9
10
11
1 2
13
74-15
16-23
a’. CRCULATION LIST 24
INVESTI~TION IF!$ POTENTIAL LOW TdI!XPERATURR VOIATILISATION
WITRIN T3Ei PROP$SXD OXFORD NEWWORXSKIE?, PFECALCIHER
ANDPREHEmmsYsTEt?s
Objectives
1) To identify potential low temperature volatile compounds in the ravmaterials of the hew Oxford Worka.
2) To assess the qua&ities of volatile8 present in the ~8 and material
streams at particular positions within the system, in particular VithiL
the preheater and precalciner areas.
3) To establish whether these calculated values vi11 affect the ccnclnsions
on the size of bypass required for the new Oxford Works.
1. INTRODUCTION
The Services Department of Research Division have produced a comprehensive
assessment of the siie bypass that would be necessary tc prevent process
problems due to volatile alkalis/sulphates within the pmposed Oxford new
Works kiln syste (STN 81/13). The report highlights problem sreaa m-icularly with reference to the effect of possible volatflisation vithin the
prscalciner or preheater system. The chemistry of the compounds concerned
is of a similar nature to tbat of materials studied by Eagineeriug Research
and Development of the processinc of cement flue dusts. This note apples
the theoretical predjctions of the previous flue dust work, together with
other infomation awilable from published literature, to the potential
problem of volatilisation in the Oxford preheater/precalciner system.
The assumptions nsed'in SIN St/I3 acknovledge that a certain amount of lov
temperature volatilisation may take place and allows for up to 3096 lov teap-
erature volatilisation with a bypass of up to 30% Rovever if low tenpersturc
volatilisation vere to exceed 3cq6, then the following problems could occur.
il The build up of a rec$rculating load within the preheater system
causing the kiln feed to have a concentration of volatile corn-
pnents which could exceed the design capacity of the bypass.
ii) The pssibility of material build up uithin the preheater system
causing blockage problems.
iii) The release of vapour particularly So2 at a temperature below the
temperature of the formation of free lime. This would mean that
the bulk of the SO2 would not be recaptured by lime but released
from the system in the stack exhaust gas, causing the bypass and
preheater design to be oversized.
2. THEORETICAL COEJDEFUTIONS
2.1 Volatiles Present in the Back end Gas.
The first stage of the investigation was to identify all the volatile
compounds present in the kiln exhaust gas;IL -.J. c
then from themdynamic
information on>heir ;zD ehavio.ar with temperature, compounds which could
cause problems could be identified. The standard volatile com_r>onentT
of X20, Na20, So3and CL were considered. The form in which these
components will recondense is well documented, and is listed below.
1) Chloride will recondense as KCl,
2) K20 remaining and Na20 ,will recondense as K2sD4 and Na2S04.
3) If there'is excess sulphate, as in the Oxford case, Cam4 will
be formed which preferentially forms the double salt (2 CaSO4g2s04) *
2.2 Calculation of the Maxfmum Amount of Material in the Tapour Phase
The solid gas phase equilibria of El, K2S04 and Ba2sD4 has been/
extensively studied at Barnstone by Khor?.
Prom curves of saturation vapour pressure tempera-e for KCl, %s04
and Na SO (see Fig. 1) the saturation mass of vapour in the exhaust2 4
gas can be calculated using the equation:
Where Ys equals the saturation mass of aUralA vamur in the exhaust
e-9
Pa is equal to the saturation vapour pressure (obtainable from Pig. 1)
P is the total pressure (atzn)
Mv i&-the molecular weight of the vapour component
Mg
is the molecular weight of the gas.
Taking the total pressure to be one atmosphere and the molecular weight
of the gas to be approximately 30 we obtain the curves shown in Pig. 2.
If we assume that 4@ of the fuel is burnt in the kiln and 6% in the
precalciner, if there is no 'bleed, the mass of gas to clinker can be
approximated to 0.55 Kg gas per Kg of clinker in the kiln and 1.7 X3
gas per Kg clinker in the precalciner. Using this information we can
obtain the CuIves shown in figure 3. which give the narimum vapouz
carrying capacity of the gases. The czurve at a higfier level in the
precalciner indicates the higher gas quantities in the precalciner.
By assuming the burning zone temperature to be 1450°C, the back errd
temperature to be 1050°C, and the precalciner to have a maximum tezp-
erature of 950°C Table 1, can be constructed. This shows that we -
would expect all the available KC1 to be vapouris-A hofnr- -a-h&
the kiln,? small amount of K.$04 to be'vapourised.&d a negligible
quantity of Na2SC4. If the precalciner is operated at a lower tv
erature (85O'C is more ty-pioal.) then the amount of K2SC4 vapourised
also becomes negligible.
This analysis recognizes KCI. as low temperature volatile, hoverer
this is also recognized in Sl!S 81/13, and the quantities of KC1 pre-
dieted in .the precalciner region by STB 81/13 (1.6% on clinker) com-
pares well the quantity predicted by this analysis over a temperature
range of 850 - 900°C (1-246 on clinker). The results of this
fundamental approach show that the assumptions made in Sn 81113
concerning chloride recirculation are reasonable. As the assump-tions made in STM 81/l-J ~~ncernina alkali recimlatian are stx-mn
to be reasonable bv this inventiaatlon. anv wtemlal aaerstinz
procuemz voula nave w ari8e rrom an cute-rnatlve source, prooablg
from sulphur contsining compounds. This is discussed in the
following section.
3. SUUHUR CONTldNISG COMEWXES .
Sulphur can be present in the kiln system from several different sources.
1) Calcium sulphate and calcium sulphide in the rair materials.
ii) Iron sulphides in the raw materials.
iii) Sulphur present in organic matter in the raw material.
iv) Sul?hur present in the fuel.
Ro similar partial pressure data to that used in the previous section wa
available for CaSO4'
CaS and iron sulphide. In this case a fundamental
approach considering the thermodynamics of the reaction of SO2 and CaO MS
considered.
This investigation was complicated by the fact that the equilibria and
rate of reaction are affected by the gas environment in which the reaction
takes place e.g. reducing or oxidising, and the presence of certain minerals
in the rav meal e.g. Si02, MgQ and FeO,
3.1 Reaction of CaO and SO2
Some of the many possible reactions of CaO and SO2 are listed belou3.
I) caso4(s) + yEI) + =2(s) + 3 O2(g)
2’ CaS04(S) + 'O(g) + ca'o(8) + =2(g) + co2(S)
3) c”s4(*) + @(*) + c”s(*) + 4 co(g)
4) C=s4(s) + 4co(g) + cas(8) + 4c02(g)
5) 3 -4(9) + C"s(s) + 4 ys> + 4 =2(g)
Beactions 2, 3 and 4 will only take place under reducing conditions
and these will be discussed later. Of the two remaining reactions
laboratory tests4 on the adsorption of SO2 on cement raw meal have
shorn that considerable adsorption of SO2 occurs in the temperatare
range 600 to goo’c according to the reverse of equstion (5).
6) 4 CaO(s) + 4 a2fg) 9 3 C=s4(s) + C=Scs)
From thermodynamic data we can obtain values of enthalpy, entmpy
and Gibbs free energy for the reaction at different temperatures.
Then using the Qan't Hoff isotherm the value of Kp (the equilbrium
constant) can be found.
DG = -2.303 %T Log K -P (2)
F'rom the stoichiometry and assuming the actitivities equal to unity,
it can be seen that Kp depends solely upon the partial pressure of
=2* From this knowledge we can obtain a curve (Figure 4.)&J ;,J/*L;& t h e
extent to which #e reactior6progreases to the right hand sic with_~.- _. --.----increasing temperature. Th2.s curve show that, at a kiln back end
temperature of 1050°C all the SO2 would be in the gas phase vhere as
over the precalciner temperature range (85O'C - 95O'C) there would be
between 2% to 1446 dissociation to fern S02. This is within the 3096
low temperature volatillsatlon allowed for in the report STH 81/13.
This equilibrium is for a static sitcation and does not consider the
removal of SO2 from the system or the rate at which the reaction
proceeds. In the kiln/preheater system the compounds are constantly
being removed and replenished and so the equilibrium is also depend-
ant on reaction rates and residence time of the compounds. This
analysis does shou however that the bulk of the SO2 will be generated
from the decomposition of CaSo4 at a temperature greater than the
typical temperature of the precalciner and so a bypaes at this Mgher
temperature would reduce much of the So2 available for reforming CaSO4
CaS in the precalciner.
3.2 Effect of Reducing Conditions on the CaS/CaSO, Equilibrium-t
If sulphur containing limestone is roasted in air all the salphur is
converted to C&O4 by the reverse of reaction (1)4.
7) CaO + So2 + 8 02 + Cas4
Reduction in the level of oxygen causes reaction (6) to be favoured
which has bee,n found to be the major reaction in cement kiln exhaust
gases. Further reduction of the level of oxygen causes reactions (2)
and (4) to be favoured. The extreme case of reducing conditions is
given by equation (3).
If CaS is present a further reaction can occur with carbon dioxide5
according to the equation.
8) CaS + 3 co2 = cao -+ so2 + 3co
!I'he temperature dependance of these reactions have been studied by
Turkdogen and Olsson5 who obtained expressions for the equilibrium
constants
10gpm2 (p~o/pco2)3 = - (20,000/T) + 9.27 (3)
lo~W2 (pC02/pcO) = - (‘9617/T) + 8.021 (4)
From these expressions the salphate/sulphide equilibrium diagrams can
be dravn vhich are shown in Figure 4, 5 and 6. These curves show that
adjustment of the ol;ygen potential of the kiln atmosphere will adjust
the level of sulphur retentio:n and that this effect is more sensitive
at higher temperatures. At the relatively lov temperatures, 95O'C and
3*5 Effect of the presence of orwic sulphur contaminoua..compou.nds
ii) the presence of potassium containing minerals very much enhances
the decomposition of CaYO4when compared to the effect of analogz
non potassium co&ainiry~ minerals. These obseroatione are valid
for temperatures below 12OO'C and at atmospheric pressure.
The presence of minerals which enhance evolution of s02, by the
same mechanism will obviously retard its recapture. This could
mean that SO2 is lost from the system via the stack in greater
amounts than that predicted by STN 61/13.
Another form in which sulphux can enter the kiln syetem is in the form
of vegetable matter. !&is vi11 evolve SO2 at very much lover temperatures
than mineral based%
. If this was the mjor form of sulphnr in the rav
materials, this uould mean that almost all the raw material sulphnr would
be lost via the stack causing the bypass tc be very much oversized. The
effects illustrated in sections 3.4 and j.5 can be investigated by eqeri-
merit and would ahow up as enhanced volatility at lair temperatures.
Experiments carried out on the Oxford raw material have not shown this fn
be the case.
3.6 Effect of sulphur in the fuel:
Sulphur in the fuel will be present in the kiln and precalciner gases a8
=2- From the discussions of their reaction of CaO and SO2 (section j.1)
it was stated that considera't)le amonnts of sulphur vould be absorbed at
600 to 900'~. In fact the peak rate of absorption for SO2 is at 850°C5,
Other factors affecting the amount of sulphur absorption are the concen-
tration of CaO and S02, the surface area of the CaO and the exposure time.. .In a kiln and preheater system the time for vhich CaO i8 exposed to So2
at a temperature where absorption can take place 18 very short. HoweV8r
the fineness of the CaO particles means that an enormous surface area of
CaO is presented to the gas stream.
This is generally the overiding factor and the reaction vi11 tend to
reach equilibrium very quickly. Hence in the stage IV preheater cyclone8
there is almost 100% absorption of SO2 by the feed.
With a precalciner the reaction is complicated by two streams of
gas and material, at different temperatures combining. The pre-
calciner gas stream will contain So2 from the fuel. The precalciner_..material stream carries‘bffsolid of increasing CaO content (see ?ig.
8). Eouever there will be little recombination of CaO with SO2 in
this stream, due to the gas temperature of approxinrately llOO°C.
(see Figure 4).
This will combine with gas and material streams from the kiln in the
riser duct from the kiln. (Por the RSP ONOQA system shorn in Figure
8, a mixing chamber is used),, This material stream will also contain
CaO and So2 from the kiln fuel and rav materials. The gas temperatare
is also around llOO°C and so there &ill also be very little combination
CaO with S02. As the gas and material progress up the riser duct the
endothermic production of CaO from CaCO3coolstthe gas and material
streams. This makes absorption of SC2 by the time more favourable.
The absorption should have reached a maximum at the point uhere the
gas and materials streams separate. The absorption at this point till
be close to the equilibrium <absorption for this temperature (-. 900°C)
at about 9% (see Fig. 4). This is borne out by operating experience
with suspension preheater kilns.
The presence of a bypass will mean that kiln produced SO2 will be bled
off immediately whilst SO2 from the precalciner will be recycled before
being bled from the system.
4. CORCLUSIOBS
1) Of the potential problem causing compounds investigated &So,, Sa2s04,
KC1 and sulphur containing compounds),Na2S04 could be effectively die+
cussed as a lov temperatie volatile (see Table 1).
2) If the precalciner is operated at normal temperatures &850°C) then
the amount of K2sD4 in the vaponr phase is insignificant. Sowever at
higher temperatures (- 950°C) a significant amount (u10W4 Kgs ger
Kg clinker) of K2S04 can be in the vapour phase. Thus a high temp-
erature in the precalciner should be avoided as it would have a
detrimental effect on kiln operation.
3) The vast majority of K SO and Na So will be in the condensed phase2 4 2 4
on the suspended solids at the bypass position. This would mean thatbleeding gas alone at the bypass position will not reduce the quantity
of alkalis in tha kil,~l system. The most effective way of reducing
alkalis would be to bleed off the dust on which the alkalis condense.
4) The quantity of KC1 in the precalciner for a precalciner operating
temperature of 850 - TCO'C is high (1-a on clinker) but this is-4%
consistent with the values predicted in ST3 01/13 and&rem results
of normal vorks operating experience. This is taken into account in
the bleed requirement.
5) The effect of sulphur is wbrised in Table 2, This table demonstrates
that the source of sulphur, the kiln exhaust composition and the presence
of other minerals determines whether the sulphur vi11 be bled off by the
bypass, recycled within the preheater, or exhausted from the stack.
6) If sulphur is present as calcium sulphate, or calcium sulphide the two
control&g parameters on the volatility are the gas temperature and gas
composition. 3ouever the effect of gas composition reduces with decreas-
ing temperature and the ev$ution of SO2 will not be large (1% mar) at
temperatures experienced annthe kiln back end, and will not be signifi-
cantly higher with reducing conditions than with oxidising conditions,
7) Low temperature volatilisation due to the presence of certain minerals,
organic matter or iron Fyrites will result in an increased SO 2 emission
from the stack but should not have any detrimental effect on the sulghur
cycle in the precalciner/preheater system.
8) Sulphur from the kiln fired fuel will tend to form a recirculating load
between the kiln and preheater unless bled from the system via the bmsa.
9) Sulphur from the precalciner fuel will form a recirculating load in thesame manner as wlphur from the kiln fuel. Houever this cannot be bled
from the system until the sulphur has been recycled.
10) Approximately 9546 of the SO2 in kiln and preheater gas streams will beabsorbed by tne CaO in the kiln riser duct providing that the gas and
materials stream are in contact for '&fficient time for an equilibrium
to be reached. This time is very short due to large 8urface area of CaO.
5. RECOI+2EDATIOBS
1) Further work should be carried out on the Oxford raw materials to estab-
lish the form in which the sulphur is present in the kiln feed.
2) As the amount of low temperature volatilisation is dependant on the
form of sulphur in the raw meal a standard method for determining rav
material volatility should be developed. If wch a method were available
it could be carried out as a normal laboratory test on the rau mterial.
The information could then be used either for design information for
future works, or as information to the kiln controller to enable zare
efficient operation of the bypass and kiln.
3) When the form of sulphur in the raw material hae been established,
a simulation of the Oxford Works raw meal could be tried out at an
existing BCI dry works, (poselibly Plymstock). Sampling throu&out
the system would then show where, and at what temperature, volatilisation
and condensation of alkali and sulphur containing compounds occura*
1)
2)
3)
4)
5)
oxford Works - Modern Dry process with sulp;lur Rypass - an
assessment of the technical risk. STN M/13. PA Loognarl,
D.S. Svift, March 1981.
Processing of Cement Flue dust.. PhD Thesis, Jaw Huei Wor,
December 1979.
Sulphur pollution from coal combustion. Effect of mineral
component on the thermal stabilities of sulphate ash dsd
calcium sulphate. Baker D.C. and Altar A. Ewironmental
Science and Technology. P!!ch 1981.
Recirculation problems in Rotary Kiln Systems.
H, Xitznann, Neubechun. Translation of Zement-Kalk-Gips (8)
338-343. 1971.
Desulphurisation of hot reducing gases vith calcined Dolomite
ET Turkdo6an & R.G, Olsson. Irorrcuz&ing & Steel %king 1978 Ho. 4.
Estiloated Alkali Vawur in the Kiln/Freheater
Gas per Kg of Clinker (no bypass
Position inSystem
WQ4 &3s/Kg Clinker
Na2w4 %s/Kg Clinker
IxL QdQTClinker
Burning zoneat 145OOC
Complete4.8 x 1O-2 1 . 4 x -210 Volatilisation
0.55 Kgs gas/ Expected
IKg Clinker
At 3ack Endat 1050°C
0.55 &P @S/ 8 x 1O-4 lo-5 5 . 6 -2x 10
per Kg Clinker
Precalcinerhigh temp. 95oOc -21.7 Kg3 es/ 5 I 10- 5 Megligible 4 . 6 I 10
Kg Clinker
Precalcinernormal temp.850°C
Negligible Negligible -21.7 &3s gas/
1 x 70
Kg Clinker
2.TAB=
Effect of Sulphur on Rw Fkterial Volatility
Source of Sulphur Conditions aff'ecting Likely effectreactions
Cam4 will be recycled being
CaS and CaSC4
Oxidising vapourised in the kiln and
condensing to form CaSO4’ in
the precalciner unless tha SO2level is reduced. CaS will
tend to form CaSC4and act in
CaS and CaSO4
Reducing Similar to oxidising cond-
itions except CaS will form
in the precalciner and the
So2 vi11 evolve at a sli&.tly
lower temperature.
FeS2 The bulk of the sulphur will
be converted to CaS but an
increased quantity of .sulphur
vi11 be lost from 'he system
via the stack.
Presence ofCaS and CaSO
4so* Fe203 Increased losses of So2 from
sodium and calcium the stack when corn-red with
montmorillonite pure CaS04
Presences ofCaS and CaS0
4Potassium containing Y&e SO2 in the stack exhaust
minerals when compared vith the effect
of SiO2 etc.
Cod/. l . . .
Source of Sulphur
Organic Sulphur
Sulphur the fuel
TABLE 2. Cont'd.
Conditions effectingreactions
LikeQ effect
A11 the sulphur vi11 be lost
via the stack exhaust.
0
Temperature ("C)
Figure It Saturation Yapour Pressure of El, K SO ank Na SO2 4 2 4
2 .FIGIJEE
Temperature @)
Figure 2: Saturation Mass of KCl, K SO2 4
and NapS04.Yapom in Air
-:18- :
__- .- -_--
_‘.- -.-
- --z
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 4
Factors Affecting Sulphate and AlkaliCycles in Rotary Kilns and the
Implications
ANDTHE IMPLIC?YXONS OFTZESE EZFFECTS KITH RESPECT ?o P-S CDNTROL
SYNOPSIS
i) To identify the fundmental and empirical relationships governing
sulphate and alkali cycles in rotarykilns.
ii) Using these relationships; to explain the kiln performance with
reference to clinker sulphate ark3 alkali retentions at bth
Northfleet and Hope M&s.
iii) In the long term, to learn kx4 best to control the rotary kiln process
with respect to sulphate and alkali levels, in order to qtimise the
prciluction of clinker that ineets current rmrket requirements.
Anexamii-la tion of alkali/sulphate cycles has 'keen carried out using
data frantrials carriedcutatNxthf1ee-t andF@e b&As. The fundamental
an3 e-rpiricxl relationships qzvernirig these cycles are discussed along with
deviations fran those relationships. The magnitude of the suggested fat-
tors ki-iich cause deviations fran the fundamental relationship is estimated
using data cbtained fran +mAs trials and ,&lished literature. This data
is then used to mre closely mcdel the real situation. The resultant r&e1
when refinedmaybe used to estimate the recirculating load of
alkali/sulphate (fran hereon described as wlatiles) within the rotary kiln
system for wxks where insufficient empirical data is available to
calculate the recirculating load using the traditional average crass balance
method. Using the fundamental relationships discussed in this report, the
requirements for a control stratq for rreintaining a'constant level of
volatiles in the kiln systxn is proposed. ll-Ls strategy is based a2 the
kiln X& signal.
i) A simple idealised wlatiles cycle within a rotary kiln can be dev-
loped frcmkncwledge
the kiln system.
of the temperature profile and gas flows within
ii) The rregnitude of the recirculating load of wlatiles in this simple
rwcdel is principally a functionof tb.e peak feed temperature. The
quantity of gas pr unit of clinker is another impxtant factor since
it determines the rraximum volatile recycling capacity of the kiln
gases: i.e. the wet process, through its higher energy demand, results
inrcrxe gas being available to
Conversely, a precalciner with
nwinff tm 90% dec~rlnnatinn &
carry a larger quantity of volatiles.
its smaller gas quantity within thekiln,
theburning of 60% of the a& cutside
the kiln in the preheater, is unable tc suppxt such ahighlevelof
volatiles as a suspension preheater !ciln or wet process kiln.
iii) The idealised cycle does rzot fully explain the cbserved situation.
However, through studying actual -rating data, the various effects
that influence recirculation canbe estimated and amxe realistic
model developed.
iv)
VI
vi)
Tne four principal factors that alter volatiles recirculation b&a-
viour fran the ideal cycle are the gas/solid mixing, kiln atmsphere
cqsition, dust insufflation and feed -ition.
The level of gas/solid mixing in the burning zone is a function of the
kilnvolume loading and the aznbined effect ofkiln speed and feed
residence time. The effect of pr mixingmuld appear tobe to
decrease the actual quantity of mlatiles recirculation to around
l/Sth to l/lOth that of the level predicted assuming an ideal cycle.
The gas/solid mixing tith reference to the recapture of volatiles
material is a function of the type of process e.g. suspension pre-
heaters are highly efficient gas/solid mixers at the kiln back end
whereas wet process kilns are rmch less efficient.
The effect of a reducing atrrosphere is to reduce thequantityof SO3
retained in the clinker and increase the So3 lost as SO2 via the
stack exhaust.
Dust insufflation will typically cause a large increase in the
volatile recirculating load.
vii) Volatile recirculation will tend to induce a cyclic pattern of beha-
viour for the quantity of mlatiles retained in the clinker *en
clinkeris~ttoaconstant~~limemntent.
The cyclic behaviour of the recirculating mlatiles causes changes in
the apparent burning characteristics of the clinker bynodifying the
quantity of flux in the pre-buming and burning mnes and also induces
a~geinfhequantityof~trequiredto~~aconstant
-iv-
recirculating load, i.e. the heat requirement for mlatilisation in
the burning zc)ne will increase *xith increasing mlatile content of the
feed.
This cyclic behaviour makes kiln axtroltc a&t-ant free lime
based on kiln amps exceedingly difficult. A amtrol strategy to min-
tain a am&ant level of volatile recirculation till rerrove this
cyclic behaviour. Ihis stability can be achieved by maintaining a
constant burning mne teqerature with a constant feed input. Mrk
carried out at I-b&pe Wrks has shown that the best relationship between
an observed kiln pa.rar&er and the level of recycle tas found to be
N&. This wouldman thataaxtrolstratqybased onK& shouldmin-
tain a ax&ant level of reci2miLation and allow the free lime wntent
to float inlinewith changes in the feed chemistry.
i) F'urtherwrk shouldbe carried cut to identify the mlue of E, the gas/
solid mixing factor, particularly wi"Lh reference to the kiln ,param+
ters of mL.xne loading, kiln speed and kiln angle. This factor, along
with thepeak feed temperature, wuld allowamre accurate estimate
of the level of bxning mne volatilisation to ba predicted.
ii) Ihe relationship between clinker m&hate and q should be further
studied to enanpss the effect of ,parameters such as B.E.02, feed ax-
position, coal consmrpticn and kiln cutput.
iii) The effect of oxidising or reducing atrmsphere cm mlatile cycles
should 'ZE studied further. Current theory and practical results indi-
cate an inverse relationship between the &antities of SO2 and 02 in
the gas stream andhence a direct relationshipbatween So3 in the
clinker and 02 in the gas stream.
iv) The effect of raw meal mineralogy shculd ke examined in order to
attempt to qmntify its effect m the ideal cycle.
VI The net effect of the thermal requirement for empczating and oHI-
densing circulated mlatiles r&is to be determined mre specifically.
This is of particular relevance where preheater cleaning causes sudden
surges of mterial with a high mlatile content to enter the 'kiln.
vi) Control strategies based on N& to mintain a azmstant mlatile
recirculation load should be develo,Ded and evaluated in preference to
those based mkiln amps and a amstant free Lime cmtent.
FIGURE t------we RECIRCULATING VOLATILE BALANCEHOPE WORKS 1977
S t a c k G a s S t r e a m c o a l
K2° 0 . 1 2 3 K2° 2.624 K2° 0.019Na20 0.033 Na20 0.180 Na20 0.005S O3 0.381 so 3 4.930
C l 0,018 C l 1 . 1 2 0
P 0.019F 0 . 0 0 0
I - - - -P r e c i p i t a t o r Duet
so3 0,480
C l 0 . 0 1 2
F 0 . 0 0 4
R e c i r c u l a t i n g L11 Volatilised i n 82 jXj
K2° 2.605
Na20 0.175so3 4.450C l 1 , 1 0 8
F 0.015
K2° 0 . 0 4 4
Na20 0.088
S O 3 0 . 0 4 0
C l 0 . 0 1 0
F 0 . 0 0 4
K2° 2.457Na20 O.l’t9
s o3 4.503
C l 1.092
F 0.015
K2° 3.125
Nu20 0.375
-IsR a w F e e d P r e h e a t e r F e e d
K2° 0.624 K2° 0.668Na20 0.218 Na20 0.226so.5 1.201 SO
31.2'11
Cl 0.009 C l 0.019
F 0.156 F 0.160
Na20 0 . 2 0 0
s o3 1.300
C l 0.003F O.lGO
83.446.7
77.11
99.78.6
Retenlion $- - -
q6.6
53.3%%,C
0.3
31.4
YCHNX%
ZCGC
ICC%
0
HOPE WORKS KILN : R E L A T I O N S H I P 6
21 I?102
Q
0
m/84/13
MD'IHE iMPLICATICNSOF'Z%SE EFFECTS WI'H RESPECT T0 PXCESS GXIWL
Page lb.
SXNOPSIS
OBJE~IVES
1.0 lzYmxum1m
Figure1
Figure2
wRecirculating Volatile Balance t30 ks 1977
raOpe Wrks No 2 Kiln vRelationship beween KilnExit W, and Clinker SO3 cbntSam Tine Base
2.0 FUNDAMENTAL RELATIONSHIPS ?G'FZTIG bQ LECYCLLES%
Figure 3 Idealised K2SO4 cycle for a Northfleet Kiln FeedLSF 98%
Figure 4 Idealised Cycle for a pe Wrks Kiln Feed
%3.0 DEXL..IONS FFXX¶ THE IDEAL CYCIE
3.1 Gas-solid Mixing
3.2 The effect ofcooler ,oart of
mixing and reaction rate in the
ical Trer& of So2 amxntratim in
of Kiln Feed Ccqosition
5
7
8
9
9
10
11
12
13
14
15
Page PD.
4.0 IKPLIC~TICNS OF WUTILE RECIRCUUVION To 'IWZ pKCl5S.S CCWjX)LOF KYI'ARY KIU?S
16
4.1 Burning Zone Temprature 1 7
4.2 Gas Qm-ktity 18
4.3 Xixing Efficiency 1 8
Figure 7
4.4 Gas solidrate
S02, NO2 and 02 axxentrations in the KilnExhaust (dry basis)
1 9
mixing in the cooler ,mrt of the kiln
4.5 Gas Clarqpsitions 2 0
4.6 -Kiln Feed CDnpsition 2 1
4.7 Ixlst Return 2 1
5 . 0 coNcus1ms 2 1
6.0 RECXMQXDATIONS 2 2
7.0 REFERENCES
APPENDIX 1
THEDRIES OF Q3NSTRUC!XoNOF IDEAL CYCE.S RM)CORREcrED IDEAL CYCLES
APPFxxx2
EEFECTOFREDJC CD!JDITIONS CN THE vOLU?ILIT'Y OF ALKALI SULE'HATES
%APPEHDIx3
HEN PIPE F KWTILE PECIRCUATIoN AT WPE KXKS
2 4
ANDTHE DIPLICATIONS OF'MESE EFEECTS KtTH RESPECf'T3 PKCESS CrXTWL
OE!JEmIvE
i) To identify the fundamental and empirical relationships governing
sulphate and alkali cycles in rotary kilns.
ii) Using these relationships; to explain the kiln ce with
reference to clinker sulphate and alkali re entions at b&h
No-fleet and I-Qpe Parks. b
iii) In the long term, the rotary kiln process
with respect to sulphate and plka in order to optinise the
prcduction of&clinker that nt mrket requiremnts.
1.0 1mmLUcr1oN
Kiln based su &ate and alkali cycles ("volatile cycles") have
\almys been of i.qx3rta.n to the cement raker, since the level of
recyclehasa 4 ficant effect co the kiln characteristics, 'the%
clinkerch ' try and the associated quality of the cement prcduced.
3Howaver, w1 e advent of dry process kilns these cycles have been
under r
Q
xtensive study due to build-up problems in the kiln ,pre-
heater an relatively high alkali levels in the clinker. i%re
rQ* enviromental pressures have added impetus to the study, due
to increasing interest in the level of q and s4, &ssiom fram the
kiln exhaust stack.
ANDTHE IMPLIC?YXONS OFTZESE EZFFECTS KITH RESPECT ?o P-S CDNTROL
SYNOPSIS
i) To identify the fundmental and empirical relationships governing
sulphate and alkali cycles in rotarykilns.
ii) Using these relationships; to explain the kiln performance with
reference to clinker sulphate ark3 alkali retentions at bth
Northfleet and Hope M&s.
iii) In the long term, to learn kx4 best to control the rotary kiln process
with respect to sulphate and alkali levels, in order to qtimise the
prciluction of clinker that ineets current rmrket requirements.
Anexamii-la tion of alkali/sulphate cycles has 'keen carried out using
data frantrials carriedcutatNxthf1ee-t a&F&e b&As. The fundamental
an3 e-rpiricxl relationships qzvernirig these cycles are discussed along with
deviations fran those relationships. The magnitude of the suggested fat-
tors ki-iich cause deviations fran the fundamental relationship is estimated
using data cbtained fran +mAs trials and ,&lished literature. This data
is then used to mre closely mcdel the real situation. The resultant r&e1
when refinedmaybe used to estimate the recirculating load of
This re,mrt piqwses an alternative .meticd of estirwiting t3e
recirculating volatiles based on the fundamental relationships
governing the process of recirculation. An ideal volatile cycle 'based
on these relationships is pro,oosed, along with ,mtulates for
deviations frcax this ideal cycle. Ran this rrcdel, a new estimate for
the internal cycle is developed for mrious kiln amditions.
These relationships are then used to support
controlstrategybased onmintaining clinker es levels, espe-
cially the sulphate level, at a constant va ue rather than to allcw
them to vary over a large range of values. b
& C Y C L E S2.0 FUNDAEEVTAL, fELATICNSHIPS AFFEcrrwG V3
The tm fmdamentalthe4
'c ,parameters which affect the
volatilization of any rmteria e the temperature and its imle frac-
tion in the gas stream (i.e. 3@al pressure). Inarotarykiln
system these are iranifeQ
the temperature of the feed and quan-
tity of gas atilabl to carry the volatiles. The relationships
between temperature,\m fraction and recirculation are discussed in
more detail ine
ndix 1, along with details of 'mw to construct an
ideal cycle. Ran these relationships we mn axstruct a diagram to
9ShGdhCWth erial is wlatilised and recondensed. Fbr the ,p.xpcse
of thi
9
rt the recirculation of mly one wlatile - K2SO4 - is
discuss , dlthough the same technique myba used for any mlatile.
Fi eQ
shows an ideal cycle diagram for Wrthfleet Mrks i%. 4 kiln.
In studying this figure, cry rmst mncieve the zaw feed being fed to
the kiln and rmving along the Xaxis until the feed temperature has
reached a pint at 5-6 'kiln diameters frm the nose ring where the
K2SO4 in the kiln feed is able to volatilise. The K2SO4 then begins
to vaporise into the gas stream where it attains the gas temperature
and is trans~rtedback along thekiln to apointtiere the gas tem-
perature falls to a level tiere the K2SO4 will reco e (and rem
-zfiiiLbine in the event of dissociation), at about 13 to 15 ' ters fran
the rose ring in the case of the first cycle.*
les will con-
tinue to build up the levels of volatile in the kiln bed until the
maximm quantity of K2SO4 tich can be is reached. This.
will occur at the &peak feed temperatur around three kiln diameters
frcm the nose ring.
example, consider
any excess K2SO4 in
with the clinker. Fbr
approximately 25 cycles
reached and K2SO4
culating load is 25% K2SO4 QI clinker.
etical kiln feed history is illustrated in figure
Theiqmrtantfhingtomtecnthiscycleisthe
ity of K2SO4 mlatilised. This is indicative of the
ility temperature of Hope tbrks kiln feed and the 1-r
1.92 kgs of gas per kg clinker in the burning zone and 2.75 kg of gas'
per kg clinker at the back end. E?qp Parks 'has 1.40 kg of gas par kg
clinker in tie burning zone and 1.94 kg of gas per kg clinker at the
back end.
100
90
80
70
80
50
b0
JO
20
10
0
t
t0
FiKurd - Iticaliscd KSO!, c y c l e f o r n NorthI’leet K i l n h’eed LSF 985\:
pdircction o f gas
4-edircctiorl ol’ feed
s o l i d t o
gas stream
K I L N DIflHETERS F R O M HOOD
LC
0
0
&MN113 NO X O3SIlI1UlOA tOSZW SSW
3.0 DJZVZ~TIONS FFCM TEE IDEAI; CicLE
The volatile rrms balance in figure 1 gives details of the maan
long tern recirculating ILoad at Wpe Wrks. If ma consider K3SO4,
the equivalent average quantity of K2SO4 recirculating is 1.94% which
is only l/lOth of that predicted by the thecretical It is
these deviations fran the ideal cycle which are in this
section, and, tiere pxsible, quantitative est f the effect of
these deviations the ideal cycle axe given. "
\The factors which are amsidered be of major iiqm2ance are
discussed in mre detail belcw. ?he ors are:-
i) The effect of gas/solid '+
the burning zone.
ii) The effect of gas/s&i g and reaction rate in the oc;oler
,"rts of the kiln.
iii) The effect of kiln atmsphere.
zone of a rotary kiln, vqmrisation till take
volatilised is in mntactwith the
unsaturated hut gas.. The rotary kiln is very inefficient at ~rcducing
this wntact, as the bulk of therraterial is contained in the feed bed
which presents cxiLy a szmllsurface to the gas strfxrnatany time.
For this reason a mixing factor (E) with dimensionless values between
0 andlneeds to be intrcxduced. The mlue of E will approach 1 tien
the gas/solid mixing is very efficient and allows all the feed +a acne
into cc&act with the gas. Thus the value of E represents the frac-
tion of the total solid surface ewsed to the gas stream. Using this
interpretation be can say that E will be a function of the volume
loading of the kiln: (a small~l.umeloading.presents wger surface
per unitmss of feed than ahigh volume loading) and the ccmbjned
Qu
function of kiln speed and kiln angle. A high . factor wuld be
expected with alowkiln slope and ahighki and vice versa.
Work is currently being carried cut has m aza-quter ncdelling as to
the precise value of E; the 'nest value ZLr hasedcnpresent
information is 0.1 to 0.2.
+The use of values of E .l to 0.2 implies a decrease in the
%maximum arw3unt of volatilisation the Iwrning zone by a factor of 5
to 10.00
3.2 TIE EFFECT OF GAS SOL ANDKEACI'ICNRATEIN'-!XEC0LERPARl'OF"
THEKIlxsi!Ls~
%This e ect is very mch a function of the type of process.
+For example, a dry process kiln &i&has intimate mixing of gas
solids at temperatures tiere reactions 6311 cccur very
ally all the volatiles till be captured. The mixing
of this part of the process can therefore be said to
apprwch unity. For a wt or semi-wet process, the tilk of feed
material is retained within the feed bed and therefore less intimate
mixing is likely resulting in a much 1-r level of Mlatiles being
captured (circa 50% efficiency).
This later case is illustrated in da'~a obtained fran an HES
bum carried out at Pamstone ibrksc21 see figure 3 here the
quantities of K20 and SO3 retained in porthole samples 1 taken from
the chain section outlet, and porthole 3 taken fra a point just prior
to the burning zone, show v-q little difference (i.e. change in K20
and only 0.5% change in SO3 content).. The stirring ction in the
9chain section of a long wet 'kiln does increase the mixin efficiency,
hence there is a sharp decrease in So3 content rtholelto the
stack of around 70% and in K20 mntent of aroundv906. It
%
is possible
that the actual mixing efficiency within a lon t kiln is likely to
be prirrarily a function of the chain
This section refers i 'tally to the oxidising potential of
the kiln atrrosphere and its-ifi?eff upon the volatilisation of sO3.
The fact that a reducingQ‘In atxrxphere as indicatedby alowbck
end oxygen content (generally
\
< 1.0%) gives rise to lu48er clinker SO3
andhigher exhaustSO2 n thehigher oxidistig conditionhas been
well documented
e
myle and Ferd41, B.-KG&~] and ~la~urne~~~.
Eetails of th possible rre&ani
&
'sins mncemedwith this process stay be
found in ' 2 tile the effect is illustrated in figure 6. The
values in
Q
figure 6 will be dependent upon the type of process
(e.g. wet ), feed and fuel -ition and burner design. The
feature is the shape of the curve i.e. a very rapid change
in SO2 content in the exhaust gas (andhence an equivalent change in
the SO3 in the clinker) for a sznall&ange in oxidisingpotential
FIQURE 5 BARNSTONE HES TRIAL NO. 6 AUGUST 1980 - VOLATILE RECIRCULATION
K2° 0.13
SO3 0.32
Feed
K2° I.77 Is o3 5.‘+3 I
I11A
Back Endof Kiln
Temp. 2-300 C ’ Temp. 800~ Temu
Ti?ICAL TRZXDS OF SO2 CO?;CE?XX4TION IY KIL!J EXYAUST
2000 1
I
1500
1000
2500 -
NZARLY ALL SULFUR?XTTED AS SO2
vY7
.?ROBABLE TREYD WL"r!LOU ALKALI FEED
----__
500
I.0 2.0 3.0 A.0 5.0
02 CO?lCEXTMTION (I)
Extracted from :
Doyle and r"er& A?$icatiocs of Flue Gas halysis to Cement i<llnCperation 9ock Products ::ov 1923
of the 'kiln gases from reducing to oxidisirg cmditions. A similar
pattern has teen observed at LXorthfleet Wr'ks during tests cm the So2
monitor where SO2 is practically undetectable at hack end oxygen
levels of qeater than 1.0% tit very quickly rises to levels of &me
500 ppn when back end oxygen falls below 1.0&[71. A change in SO2
concentration in the exlmust gas at Sbrthfleet of 0 500 ppn So2 is
the equimlent of approximtely 0.4% SO3 a2 clinker.b
vb
3.4 TE-E EFFFCI OF KILN FEED (XXKSITION
This can be categorised into tin0
i) &The effect of the rawrreal chemis
ii) ‘The effect of the rawrieal&
try after being rrcdified by
recirculation.
@YcementrawrEa1s
Tit
mly differ in the absolute quantities
of volatiles, but also tt*o meals -tith the same mlatiles amtent
may have very differe%Y' eralcgy. Mrk by Baker and r~tmarrC81' for
exarqle, has that certain minerals have a greater propensity to
encourage the ationof SO3 in particular. These mineralsinlpartanind ' ualcfiaracter to the particular rawmaal. and there iseno way as yet estimating their effect upon the recirculation pat-
tern ex4%
empirical techniques.
@irculation of the mlatiles themselves causes the content of
volatiles entering the burning zone to increase. This has tm affects
upn the burning characteristics of the raw meal:-
i) Both the armuntof flux within the burr&g zone and the
apparent length of the burning zone will tend 'io T. in
increase in kiln amps due to increased volatile load could, for
example, be mistaken for an indication of overburning and any
resultant reduction inburning zone terrrperature axld lead to
an increase in clinker free lime. An increase in fines within
the systemwillalso tend to encourage clinkerw
ctions
which in turn should decrease the free Ii, axtent.
77T7
ii) The evapration or disocciation of the wlatlles in the burning
XTzone will de-r-and a significant quantity high grade heat fran
the flame. ?%is high grade heatk
ver, is recovered further
dcxn the kiln as lw grade h t when the wlatiles recondense.
+Pa estimation of this 'heat ' effect" is shown in appendix
3. The overall effect * tiat the recirculating wlatiles make
%a significant demand (up 100 kcals/kg clinker) upon the heat
atilable in the zone andhence they tend to increase
the totalheatinputreqirementto the kiln.
\f&s could aggrevate each other and with the net
system, raw
mealch 'stry, and the oontrolstrategy smployed.
+
3.5 THE EFFECT OF RETURNED lxiZ?I
A rmjor differenc:e between the idealised cycle and the real
4.C
situation is, that although much of the recirculated mterial
condenses cm solids derived frcan the kiln feed, these solids are
generally held in suspension and therefore swept frcm the kiln in the
gas stream. If the dust is returned, especially by lation, then
the observed cycles should bqin to approach th
mixing factor (E) will begin to approach unity.
YThe greater the armmtof dust return , the greater the
recirculating load and hence the clos clinker mlatiles till
to the system (except for
at t-ratures within the
burning mne is considerably ter than cne at-sphere and hence, ir
%theory, should have an k-finite pacity for volatilisation).
e0
IMPLICATIONS OFKKx4T&E FECIRCUIATION~ PIE Pm C?N'I'floLOF
mARY IiIL~S
This s4
discusses the implications that mlatile
recirculatio has onkiln mntrol.
42
ijherever possible the individual
factors dis ed in the previous section are related to kiln cofkrol
parame sfo
uch as burning zone temperature and kiln feed rate. SOme
of the factors such as recapture of mlatiles will tend to be related
toc&-ss design rather than any &aarameter tNhich can be altered as
part of a control strategy. These should be rmted, as it is highly.
probable that any control strategy considering mlatiles recirculation
muldbe dependent to a certain extents the type of,orocess.
The quations given in table lcgl shm the iqxtance of
temperature as a factor amtrolling mlatile recirculation, because
the amunt of recirculation has a logarithmic relationship to
temperature. In a dxy process kiln, the usual strategy is to control
the kiln to produce clinker to a selected range of fr 'w
e cmntent
by mnitoring the kiln amps. This signal is a function of, amngst
vY7other things, the amount of flux present in the )u . However, in
section 3.4 it was pstulated that volatileT
irculation will mxlify
the armuntof flux in thekilnwith litt or m change in the fuel
&inputratetothekiln. Thekilnmps ' therefore be dependent to
sane degree cn the rragnitude of the tile cycle.
iii?
Akiln control
strategybasedmthe amceptof ' ining a steady level of kiln
amps is likely to disturb the%
'les cycle when recovering fran a
process disturbance khich '
-Q
in turn affect the ammtofkrning
zone flux and hence kiln For example, a perturbation in kiln
feedchenistrythat'%
eases mlatiles till tend to,increase 'kiln
Zip. react by reducing the BZT to maintain the
amps set pint the clinker produced would be both underburnt
in mlatiles.
Q tant coal feed strategy is similarly insufficient to
makltain le kiln control, as any increase in recirculating
Qvo1tiwill tend to depress the temperatures in the burning zone
andhence theheat inwtto the kiln will heed tobe wied in order
to control the solids temperature andhence the clinker free lime
content.
In order to mintain a specific temperature in the burning zone,
the best ,Darameter to consider is therefore the peak feed teqerature.
Unfortunately present day instrumentation is unable to supply a
reliable direct indication of ,oeak
method of establishing a peak feed
parameter qon which the peak feed
feed temperature. An alternative
temperature is to measure the
temperature depe fhe W
gas teqxxature. This maybe carried out indirectlyby&asuring a
parameter dependent upon the peak gas temperat
This will then be a function of the peak
that the feed rate is n-aintained at a constant level. The
relationship between NO, and clinker So4
as alreadybeen discussed
(see figure 2). Further evidence fo the relationship between wlati-
les content and N& is show in fi&
. Here the kiln exit So2
concentration is seen to foil exy step change in Q, highlighting
%the particularly strong correla ' between these tko ,oarameters.Clll
4.2 GAS CXJANTI'IY 00
%?This, as mention previously, is principally a process design
variable. Any on the mlatiles cycle due to gas quantity
changes assoc' ted with fuel changes are liable to be masked by the
greater s4
* ty to changes in the burning imne temperature.
The appr
Q
te strategy txxards gas quantity control should therefore
be-try mintdin constant gas flew through the kiln together with
a t feed rate.
4.3 MEQNG EFFICIENCY
This factor is essentially determined by the process design.
As discussed in section 3.1, the efficiency (E) is determined by a Ccnr
bined function of the kiln speed and 'kiln slo,pe which determines the
amount of effective surface area of feed within the burning zone. As
a consequence of the gecmetry of the circle, a significant change in
volume loading will only have a small change in the effective surface
area of the feed within the typical limits of kiln volume loading. As
thekiln angle is fixed, thekiln speed is the cnly cess'FIT
le para-
meter tich can have any influence ctl the wlatile cycle. It is
postulated that this influence should not be larF
rasmallrange
of kiln speeds as there are tw opposing effects. An increase in kiln
32speed would increase the rate at which effecti surface of feed is
exposed for volatilisation to take pla+L
but decrease the time
available for evapration. I t is p tulated that the likely effect
is for them to cancel each othera
'In speed is therefore
unlikely to be critical in a constant level of
volatile recirculation.
\This is similarly a function of process design. Changes due to
this effect mule
causetl in bet process kiln by altering the chain
design but ges during operation of the kiln are unlikely to affect
avolatiles r ure. (Gas wition tich affects this will be
discussa
the next section).
4-5 =fFF=As was stated in section 3.3 a &ange in oxidising~tentialof
the kiln gases can have a large effect cn the recirculation of SO3.
If a strategy of maintaining a constant wlatiles cycle is to be
achieved, a constant back end oqgen level will be necessary.
4.6 K!ZN FEED CMFOSITION
The effect a2 kiln mntrol of the kiln feed rrcdified by mlati-
les has already keen discussed with reference to temperature in sec-
tion 4.1. If%wever, even if a constant level of recycle is rmintained,
there stillmyke changes in the feed chemistry entering the'azming
zone due to changes in feed &en&try of the raw f cau edby
-9
inade-
qUate blending. Pius, as with the strategyofhrning a target
free line ken &anges in LSF of the feed muldv
instability, a
control strategy based cm mlatiles also r*es mw feed of
consistent chmistry.
4.7 DUST KEI'UEN
A dust return system tends rate 01 a discrete level (ie.
either on or off).
return systan till dis
tiles input will affect
culating load is
thatwuldbe affected
either turning cn or off a dust
cycles as the change in iciln wla-
Ps the size of the recir-
dependent, the mjor factor
- the mixing factor. 'Ihis muld
take cm anew%
and a mew volatiles recirculation equilibrium
bymaintaining a steady Wrning zone tmperature.
lised volatiles cycle within a rotary kiln can be deve-
kncwledge of the temperature profile and gas flows within
the kiln system.
ii) The magnitude of the recirculating load of mlatiles in this simple
rmdel is principally a function of the peak feed temperature. Another
factor, the quantity of gas per unit of clinker, is iqxxtant since
it determines tie mxirmm mlatile recycling capacity of the kiln
gases: i.e. the wet process through its higher
in more gas being available to otrry a larger
Conversely, a precalciner with its smaller gas y within the kiln,
owing to 90% decarbonation and the burning of -1 outside
%kthe kiln in the preheater, is unable to supp uch a high level of
volatiles as a suspension preheater ki wet L;rocess kiln.
iii) The idealised cycle does not the observed situation.
Ffowaver, through studying actual cpen
ing data the various effects
that influence recirculation estimated and a mre realistic
model developed.
iv) The four principal fa(;tors tit alter mlatiles recirculation baha-
\via= fra the ideal cyc .e are the gas/solid mixing, kiln atmqhere
fflation and feed amposition.
The level of solidmixing in the bnxning zone is a function of the
kiln mime4!ti1 '
residenQ
g and the ambined effect of kiln speed and feed
') e. l3e effect ofpr mixing wuld appear tobe to
the actual quantity of wlatiles recirculation, to around
l/lOth that of the level predicted assuming an ideal
cycle.
The gas/solid mixing with reference to the recapture of volatiles
material is a function of the type of process e.g. suspension pr*
heaters are highly efficient gas/solid mixers at the kiln 'back end
VI The effect of a reducing atmosphere is to reduce the quantity
contained in the clinker and increase the So3 lost as SO-2 via
stack exhaust. wvi) IXlst insufflation till typically cause a large in the
volatile recirculating load.
vii) Volatile recirculation will tend to indu a cyclic pattern of beha-
&viour for the quantity of volatiles retain in the clinker hhen
clinker is burnt to a amstantfree '
e?
wntent.
The cyclic behaviour of the re
@%z
ating volatiles muses changes in
the apparent burning characteris s of the clinker byrzdifying the
quartity of flux in the uming zones and also induces
a change in-the tomintain a constant
recirculating load.
whereas wet process kilns are mch less efficient.
of so3
the
QThis cyclic b&ml mkeskilnmntroltoconstantfreelimebasedcxlki e exceedingly difficult. Aamtrolstrategy to n-&n-
tain a 03 tan level of volatile recirculation will rezmve this
cyclic 43OUT. This stability can be achieved by titaining a
burning zonetmperaturewith aoonstantfeed input. Wrk
out at Hope Works has st-hown that the best relationship betm
an observed kiln parameter and the level of recycle was found to be
PI%. This muldman that a aontrolstrategybesed QIQ shouldmin-
tain a asnstant level of recirculation and allow the free lime content
6. FBXMGBDATIONS
i) E'urther mrk should be carried cut to identify the mlue of E, the gas/
solid mixing factor, particularly with reference tc the kiln parame-
ters of volume loading, kiln speed and kiln angie. This factor, along
with the peak feed temperature, kould allowarmre acwe estimate
of the level of burning zone tolatilisation to redicted.
T?Y7
ii) The relationship bst*en clinker sulphate an F.Dx should be further
\studied to envss the effect of ,mrameters s as 3.E.02, feed am-
position, ~1 consmption and kiln ou6
.
iii) The effect of oxidising or reducin sphere cc mlatile cycles
should be studied further. %zCurrent
4
ry and practical results indi-
cate an inverse relationship the quantities of SO2 and 02 in
the gas stream and hence ect relationship between SO3 in the
Qclinker and 02 in the gas s .
iv) 1The effort nf raw ek , ergiccv &c&d be examined~~im-order to
atterqt to quanf;
%its effect m the ideal cycle.
VI The net eff
e
the thermal requirement for evaprating and cm-
densing c' cul ed vclatiles reeds to ke detemiined mre specifically.
This is&icular relemnce where preheater cleaning causes sudden
SIX f mterial with a high volatile cmntent to enter the kiln.
c3vi) Control strategies based on Mx to maintain a constant mlatile
recirculation load should be developed and emluated in preference to
those based on kiln amps and a constant free lime ontent.
7. F33ERExcEs
1)
2)
3)
4)
5)
6)
7)
9)
10)
Weber P. Heat Transfer in Fbtary Kilns with due Regard to Cyclic
Processes and Phase Formation. ZKG tiglish Special Edition 1963.
Longman P.A. Swift LG. Oxford Mrks -~twem Dry Process with sulphur
By-Pass - An asseswnent of the technical Risk.‘ SI'N 81/13.
Rogers A.R. Assessment of the potential to q-tin&sewperformance by
application of improved prczess sensors : tinit *
Kiln September 20-24th 1982. TN 82/28. vY7
of I-bps wxks
Coyle B.W. and Fenk F.W. Applications of%
gas analysis to wnent
works operation. FwkPrcducts, Nov19 .
Brmm A.W. 4.2Retention of Alkali and SuLph in Clinker. FkSXCh
Division Repx~tis 1 and 2 SP-65/33
Chadbume J.F. 9
, SR-65/7/M&3.
Continuous i% 'tar' g of Gaseous Emissions an Cement
Kilns. Paper presented to4
d Meeting of the fir EMlution
Control Association, Jun 9.
QLorimer A.D.J. cklline 802 nitoring : Assessment of LXXJV and
Electrcchemical cell%terns at Northfleet : May to October1984.
m/84/21.
EBkr D.C. andkA. 8ul.phu.r mllution &an coal ambustion.
Effect of ' Cxnponents cn the Them&l. Stabilities of sulphated
Ashand
@@
cium S&hate. EZlvironmental Sciences and Technology,
March .
m
. The processing of Cement Flue Ibst, PhD Thesis, ?he
University of Aston in Birmingham, December 1979.
Haspel D.W. Le@ Grate Mt Transfer bechanisns. TM. IxJH.005,
Weardale bbrks, 1973.
11)
12)
13)
Gq2pelle M. Analyser 2.3nk at the ?A &3vre lbrks. CETIC mviromt
Sub-m-mission September 1984.
Turkdqan E.T. and Olsson R.G. Desulphurisation of Wt Reducing Gases
with Calcined l%lmite. Iron Making and Steel ?&king No. 4, 1978.
Myers J.C. Sul&ur Balances in @m%t Kilns and ilers. !4Sc
Thesis, University of Texas, Austin, 1977.
D. stenson&De r 1984
@Y
(i)
APPENDLyl
THM)RIES OF FECIFCULATICN, 3-E CTINSI'X~ION OF IDEAL CYCLES
The volatile aanponents of aarnent raw mals and fuels are
vaporised ken the feed temperature is raised to a level tvhere the
vapour pressure of the volatiles bscunes significant. The wlatile
caqments will then impart a partial pressure to the gas stream. Cn
cooling, the vqmur pressure of the arnponents will decrease causing
condensation. E?y measuring the kapour pressure of certain cmpments
at different temperatures, enpirical relationships for the saturation
vapour pressure and temperature have been established. Equations
relating saturation vap0u.r pressure to temperature are given in
table 1, equations 2 to 7 and shown graphically in figures (i) to
(iii) C91.
The saturation repour pressure can bs used to calculate the
saturation vapcur mncentratiun by applyirlg Raoults Law:
vf = P* Mv (1)PT Gj--
where vf is the saturation concentration of bap3ur in the
carry% gas (kg/kg 9as) l
P* is the saturation vapour pressure (any pressure unit)
P is the pressure of the gas (same units)
Mv and m are rm1ecula.r lHeights of the vapour and gas reqpec-
tively. An example for the saturation axcentrations of I@1 and K2S04
in air is shown in figure iv.
Examples of bw to construct a volatile cycle using equations
ltc 7 is shcmlbs!low.
(ii)
The first stage in oonstnxting an ideal cycle is to obtain a
feed and gas temperature profile. For this, kxwledge of the ox-
binability of the particular feed for a particular targetted free lime
must be available. This can be cbtained fran empirical data. This
will give the pfaak feed temperature. In the exarrples shown below the
peak feed temperature for the wet process is lSOO°C and 1490°C for the
dry process. Azonedheatbalance rrcdel for the kiln can then be used
to derive a temperature profile. Fbr cur examples the temperature
profiles are sho+m in figures v and vi (the oscillations in figure (v)
are due to graph interpretation; thecurveshouldbemth). By
use of equations 2-7, the partial pressure of the volatile QsmFonents
maybe calculated. Equation lwill then give the saturation vapour
concentration. The mlecular weight of the gas is estimated frcm its
ccqosition. The calculations are sumnar ised in tables 2 and 3.
By mking assumptions for the gas quantities at various &mints
in the kiln, the actual amount of mlatile &per !kilc.grarn of clinker can
be found. 2-ii.s is s-ised in table 4.
Table 4 can be used to amstruct an idealised cycle as seen in
figures (vii) and (viii).
Ekplamtion of the idealised q&e
To explain the idealised cycle, an example of akiln to&ich
is fed the equivalent of 2.0% K2SO4 in the feed and fuel is 0311-
sidered. Cm the first cycle the feed will be tranqmrted by the
turning action of kiln until, in the case of the dry process in figure
(vii), a pk.nt4.5 diameters frm the rrxe ring is reached. Here the
feed reaches a teqerature where significant empration of K2SO4 Qn
(iii)
occur as K20 and sO3. The m:.atile afnpments are taken up 'by the gas
stream &ere they rapidly achieve gas tmperature and are tranqmrted
away fran the burning zone to the back end by the kiln draught. At
twelve 'kiln diameters the gas tenperature has fallen to a level tiere
significant condensation as K2SO4 on cccur. This is then inmx-
porated txck into the feed and transported fomds along with the
fresh K2SO4 fran the kiln feed.
On the second ideal cycle there is an quimlent of 4.0% ~2~04
in the kiln feed approaching the burning zone. The cycles will con-
tinue until a +.ntattw kiln diameters tiere the riexi~um allckable
evaporation determined by feed temperature is reached. Ebr the dry
process curve this is 16% m clinker after eight idealised cycles. Cn
the ninth cycle the K2SO4is raroved fran the kiln in the clinker as
the equivalent of 2.0% K2SO4.
The corrected cycle
The idealised cycles shown in figures (vii
followzd in practice.
) and (viii ) are rx3t
The factors of 'mixing efficiency in the burning zone and
backerd, dust loss and reducing conditions all account for deviations
fran the idealised cycle. Tables 5 and 6 give results of calculations
based m assumptions of suitable Mlues for these factors. Fran fhese
tables, figures (ix) and (x) are cbtained. 'Ihe solid lines cn figures
(ix) and (x) indicate the 1evels of mlatile corrected for the mixing
efficiency. The broken lines show further axmctions to decrease the
amount of material recaptured in the cooler parts of the kiln due to
dust loss and reducing conditions.
TABLE I- - ^ - - I - -Saturated Vapour Pressure of KCl, K SO and Na SO3--4- Z-4
Reference
LoglO (p,/atm) = - '47oo 5 9oo
Decomposition Suppreoscd
Loglo ( ps/atm) P ' - ' "O" 5 'O"
Loglo (po/ntm) 6.23
Hart and Laxton, 19671llalntead, 19701970(cf. (cf. Koaugi,Koaugi, 1967;Duboia et al, 19613)19613)
Cubicdfotti andDccomnPnit.lPn, ‘ Kuneahea, 1972
I Loglo (pa/Atm) = -y -t 7*oe1 I 1 4 0 0 1 4 0 0 -- 1 6 2 5 1 6 2 5
g 0 . 3 0t:uh
5“,g 0.25-
‘0Lla52 0.20 -
0.15 -
0.10 -
1200 1250
Temperature (“Cl
Saturated Vauour Pressure of SC1
6omce: JANAZ', 1960 or J.snz, 1969)
3-
.5-
.o-
S-
10 -
OS-
TJ,zzz ( ii)______---s-.-
Decomposition unsupprrsscd
A- DecomposXon suppfms*d
I I I 11150 1200 12so 13M) 1350
Temperature ["Cl
Saturated Vawur and Decomuosition ?ressures of K,sO.
ISource: Eart and Lax-ton, 1967; Salstead, 19701
1.c
0.'
0.f
z 0.1
ri)Tz
; 0.63::v&
g 0.5
Pv1
",1 0.4
;;:
0.3
0.2
0.1
0.0
?ICc?z (iii)------------
Temperature ("Cl
Saturated Vaoour and Deconuosition Pressures of Ha SO
(Source: Cubicciotti and Xeneshea, 1972)2-4
.Cu
C0.-
1V
Temper abre ( l C )
Saturation Capacity of XC1 ad IT SO Vau0u.r2 - - j - - - - - - - -in Air from llOo-l’jOo°C
FXCURL (v) F e e d uh ps tempeniturc p-oSi1.e :wL. t PI~oce:is_..-------- ------..__ _..--__ --^----_ -----..------------.--
6 - F E E D TENP6 - GM TEW
25002500
20002000
SD0SD0
E’IGUNL ( v i )..--------c-Feeh and- - - L - - d - -- - - L - - d - - gas temperature proTilL?proTilL? :I)ry:I)ry ‘rOCCS9- - - - - -- - - - - - ^^-CI________------L.-------^^-CI________------L.-------
0 -- FEELIFEELI TEHP
“.-.__-_
.-.~-‘.-7*‘- -2 o *-..-. .__ -.. _. _
-i’ --i+---- “--T- -.-+-- -+..--
+s-.-;‘s-- 1 21 2-,-,-- -I-. _-,
1010 1 11 1 14 15 IE
K I L N OIFlMETERS F R O M N O S E R I N G
0
1
2
3
4
5
6
7
8
9
1 0
11
12
13
14
15
1 6
Gast
WC
500 1250
600 1350
1150 1450
1500 1500
1870 1350
2om 1260
zcoo 1130
1950 10(X
1870 950
1710 910
1550 850
14.60 810
1370 axI
1330 730
1290 690
1250 650
1203 600
i
Sabrated Concentrationi.3 qas (!&kg p.5.)
Kcl K2So4 -2504
0.601
knit*
. .
45.27
5.62
2.46
1.16
1.99x10- 3
0.169
9.95
infinity
0
.25x10-3
0.232
I.
I,
9.95
1.45
0.281
0.111
0.040
0.0246
4.29
0:429
0.140
0.042
0.0239
0.0148 0.0131
3.67x10-3 .02~10-3
~27~10-3 -06x10-3
.2.$6
infinity
*,
2.93
0.474
0.091
0.046
0.023
9.65X10-3
4.71x10-3
3.9SXlo-3
9.59x1&4
K2SO4
3.07x10-3
0.031
0.099
0.169
0.031
3.94x10-3
1.45xlO'3
?ia2SO4
7.02~10-3
0.032
0.123
0.232
0.032
3.24x10-3
3.64xlo-3
T?%aLz 3. DE ?5cGss
soO f
Ciln
liameers
Feed.tcqY
WC
0 605 1370
1 aao 1417
2 1594 1460
3 2110 1416
4 2274 1273
5 2227 950
6 2106 925
7 1940 8%
a 1799 a74
9 1678 a56
10 157s a42
11 14a5 a30
12 1407 a21
13 1338 al4
14 1277 ma
15 1224 803
16 1177 798
-
Satc.zit+d Concemraticnia 9 (kq/kg 9s)
KC1 K2So4 -2So4 XL K2SO4 .*2SO4
0.434
infhity
,.
430.0
3.465
0.983
0.360
0.144
o.ffi14
0.0272
0.0125
;.03x10-3
3.02x10-3
0.737
infinity
6,
84
4,
a*
159.4
2.208
0.583
0.192
0.0700
0.026a
0.0108
t.59x10'3
2.05x10-3
L-lfinhy
I.
4.
*a
3.78
0.046
0.031
0.0204
0.0144
0.0107
a.4xo-3
6.a2x10-3
5.81x10-3
S.llxLO-3
4.57x10-3
4.17x10-3
3.79x10-3
0.0400 0.0423
0.0688 O.oaol
0.111 0.140
0.0681 0.079
0.0118 0.0101
TAaLz 4.
(xiii)
Sal 33LriJ Tl,ss
0
1
2
3
4
5
6
7
a
9
10
11
12
13
1 4
1s
1 6
11
12
13
1 4
15
16
2 0
KC1 K2g4
in5.nity
. .
514.0
6.6
6.1
4.65
2.07
2.12
1.67
1.37
1.16
1.02
0.96
0.03
0.75
infinity1.
817
324
170
5.72
9.04
LS.87
9.74
1.69
6.25
11.45
20.02
lo.a7
1.44
28.4 0.382
12.2 13.9
5.45 5.33
2.49 2.14
1.20 0.913
0.61 0.408
61s-.1n:sr+y
I.
732
14s
27.9
14.1
7.65
2.9s
1.G
1.21
0.29
Sas c3 solid
infizity
,a
13800
1719
752
354
0.44
2.17 1.7S
7.75 a.00
24.7 30.1
$2.23 33.0
7.75 a.0
2.4.a 2.06
0.44 0.264
33.9 42.3
12.2 12.3
7.32 7.31
4.53 4.01
2.65 2.1s
1.31 0.94
.%2SO4
Dry mess124 scc/x;$ :Ks ‘aup w
5 diamzter
1.43 kg/k; clizkz
Aker 3
Diemeters
1.99
wet prccess213 sx/lZi :s ?dUp to S
Oiaetezs
2.499 icg/kq di-k
After 5
&meters
3.059 kg/k;/cli*e
Rt:t
.c
+.h
so
50
40
so
20
10
0
FIGURE (viii)--1----1----- Idcnliscd cycle for NA2SOlt-----_----------^---__^___
6 - D R Y PROCESf.!l - Y E T PROCES
KILN DIRMETERS FROH NOSE RING
(xvi)
Table 5
Corrected Cycle for Mixing Efficiency
No. ofkilndiameter
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
11
12
13
14
15
16
! Concentration (% &per Kg TClinker
KC1
Infinit
8,
I,
0.8
.32
.22
.8
0.57
0.42
0.33
0.27
0.23
0.20
0.18
0.17
0.16
lilfinit
I,
856
340
Dry E2m !SS
K2SO4 Na2SO4
1.14 1.21
1.97 2.29
3.17 4.04
1.95 2.17
0.34 0.29
30.3
12.89
5.72
2.61
1.26
- -
40.1
14.6
5.60
2.25
0.96
1 179 1 0.64 [ 0,43
Concentration (S pr KgClinker
KC1
123
Infinit:
‘I
‘I
1,
146
29
5.50
2.82
1.53
0.59
0.29
0.24
0.06
Infinity
I,
15870
1975
865
IGet EYOI
K2SOq
0.434
1.55
4.94
1.55
0.496
0.09
39.0
14.0
9.02
5.21
3.65
ss
Na2SO4
0.35
1.6
6.02
11.60
1.6
0.412
0.053
49.2
14.7
8.41
4.61
2.47
TUSlimptions
%2 = 0.2
EBE m
= 0.95
= 0.85
hii)
11
12
13
14
15
16
11
12
13
14
15
16
11 146 192 la7 236
12 61.6 70 67.2 70.4
13 27.4 26.9 43.2 40.4
14 12.5 10.8 25 22.1
15 6.04 4.60 17.5 11.8
16 3.08 2.08 7.24 5.2
bxclusicn (1 per kg Clinker)cry prccess T
infinity4.
1027
408
215
36.4 48.1
15.4 17.5
6.86 6.72
3.13 2.70
1.51 1.15
0.77 0.52
121 160
51.2 58.4
22.9 22.4
10.4 9
S.04 3.a4
i.56 1.72
CmclL;sim (3 per kg Clhkr)Xet Praess
KU
infinityI .
19KXl
2370
l@iO
4aa*
QSO4 Xa2SO4
46.8 1 59.0
16.8 17.6
10.8 10.1
6.25 5.53
4.38 2.46
1.81 1.30
!x5; lass
= 20% cn
Clinker
156 197 Pfhdng
56 58.8 Cmditioixi
36.1 33.6 SQ3
20.a 18.4 RecoroirationS
14.6 9.88 decxe.asedby
6.04 4.32 75%
ca7biii
ZffeG
?ss.ui&ons
~‘IcilJlikb ( i x )..---------.wCorrc?cLcd Cplc i-'or KL'CO'I_____---.---- --^------.--.---
2 0
16
16
14
1 2
10
6
8
4
2
0 f0
< i.i;oLlt, 'ITJ GA@ - D R Y HIXINC FRCTOR
X
CJ- YET HfXfNG FACTORA
3. &if 'I'0 SOLIIJ- DRY DUST LOSS V
0 - YET DUST 1x - D R Y REDUCIx - Y E T REDUCI+ - D R Y CBH8IIy - Y E T CbHBIt
6----I
--w-e --I--- l\ I I
Ix \ ,,\ 1\ >(\\
\
I\ I
1\\ -I- ’ ’
\ , ’
‘Q x y\
\ J ’
-\ \ \1\ ’\ ’
\GL \
KILN DIRMETERS FROM NOSE RING
FIGUHC (x)------.e--- C o r r e c t e d Cplc l*‘or IJA2L;ch_-__..------- -^I-------c----
6 - D R Y tlfXINC FRCTCJR < SULID ‘I’0 cxs
2 - Y E T tiIX1Nf.i FRCTOR cA!i TO SOLID- D R Y D U S T LOSS
@ - YET DUST LOSSx - DRY REDUCINGx - YET REDUCING-t- - D R Y COMElINED‘f - YET COMBINED
K I L N DIRMETERS F R O M N O S E R I N G
Effect of Reducing Conditions cm the Volatility of Alkali Sulphates
The precise mechanisins by which reducing conditions within the kiln
remove SO2 frm alkali sulphates is not fully understood. Eiowever, it is a
real effect observed and documented by my other mxkers in this field, e.g.
Chatiume , 4 and by Brcx& fran within Blue Circle;
A similar chernicalprccess to the removal of SO2 is the desul@rising
of steel using lime. This has been extensively studied by Turkdogan and
01ss0n. 021
The reactions described by Tuxkdogan and Olsson involve only calcium
sulphate. However, for cur plrFoses we riay irake the reasonable assumption
that the alkali sulphates till undergo similar reactions, as is suggested by
their relative psitions in the periodic table of elfments.I
Calcium sulphate will deccqcse under the effect of heat alone by the
reaction :
CaSOq(s) = CSO(~) + SO2(g) 4 h$2(g) &Gs = 408 W ml-l
Wwever under reducing amditions the follwing reactions will be
preferred:
(1)
Ea.504 + cqg) = cao(s) + S02(g) + ~203~) AGs + 15 Id ml-l (2)
=04(s) + e(s) = =(s) + “co(g) 4@ + 297 kJ m31-1 (3)
C&04(S) -+ 4CO(g) = CELLS + 4C02(g) AGS - 183 kJ ml-l (4)
where&? is the c%ange in Gibbs F'ree E&qy at 25°C and L atmosphere
Reabsorption of SO2 till corer bythe reactions:
$CaOo) + 4SO2(g) = 3CaSO4(,) f c~s(~) ;lGs - 787 W x11-l
or in the presence of oxygen by the reaction:
-o(s) + SZ(g) + $02(g) = -Q4(s)
The wlue:GS is an indicator of the
occurring under standard conditions (289K
.GS - 409 kiJ id-1 (6)
pssibility of reactions
and 1 amsphere). If the mlue
ofSGs is negative, then therrm$mmically the reaction should proceed qmn-
taneous1y. Generally the mre Ixksitive,UY, the rmre heat is required in
order to m&e the reaction take place. Thus cne would expect reaction 4 to
be favoured rather than reaction 1.
This analysis takes m amount of the kinetics of the reaction.
Howaver, sane idea of the reaction kinetics under oxidising and reducing
conditions my be c&An& by mnsidering the relative reactivities of SO2
ami so3. ?hermlecule SCl3is ilDre reactive than sO2, both in terms ofkine-
tics and therrr&ynamics, so the preferential formation of So3 rather than
SO2 wuld lead tomre sulphurbeing in a reactive formtiere it muld
react with tie available GO, KS, t&20 etc. 'Ihe equilibriabetween So2
and SO3 have been studied by LMyers.C13] Fran the eqirical equations
obtained byMyers, the graph in figure 2 (i) can be axstru~ed. This
shms that the higher the percentage 02 present, the more likely is the for-
mationof SO3 andhence the formtionof sul+ates whichtill. be mptured
bythemcuningfeed. The lcwoqqen curves shas thatsulphurwill be
present as SO2 which can escape in the'kiln exhaust. Ektreme reducing
conditions lead to the formation of H2S reaqnisable by its “bad egg"
odour: inthis case therewuldbe virtuallymrecapture of sulphurbythe
on-feed.
(xx-ii)
00
%S
t0
00
00
0
0a
PDu
a-
n
::
4‘.
d
EQ
S’Q
I
20
s
NLlIS1J3hN
83
x
(xxiii)
APPENDIX3
Heat pipe effect of volatile circulation at F!op? ibrks
i) Latent Heats of Vapourisation/Disscciation N.B. V = VqxmrisationD = Dissociation
KC1 + 670 Kcals/Kg (v)
K2S04
Na2SO4
+ 563 Kcals/Kg+ 1805 Kcal.s/Kg
Obtained fran Khor+ 733 Kcals/Kg+ 2096 Kcd.s/Kg (A?
c91
caso4 t 675 Kc&/Kg (D)
Recirculating volatiles
K20 2.457 % on clinker
Na20 0.149 % on clinker
SO3 4.509 % on clinker
Cl 1.092 % on clinker
This is quivaledto
KC1 2.29 % on clinker
K2SO4 1.94 % on clinker
Na2SO4 0.34 % on clinker
CaS04 5.46 % on clinker
Therefore Heat pipe effect, assuming all mqxmznts disscciate fully, is:
KC1 16.46 Kcals/Kg clinker
K2SO4 10.92 Kcds/Kg clinker
35.02 Kcals/Kg clinker
Na2SO4 2.49 Kcds/Kg clinker
7.13 Kcals/Kg clinker
CaSO4 36.85 Kcals/Kg clinker
Total 108.87 Kcals/Kg clinker
Therefore rraxinnrm total heat pipe effect for I-bps is 109 Kc&s/Kg clinker.
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 5
Alkali Volatilization- A Review ofLiterature Available in 1977
ALKALI VOLATILISATION
A iU3VIEFw OP LITERATURE AVAILBBcg IN 1977
Information from 119 published references has been collated andcritically reviewed. The effect of alkalis on clinker properties and kilnoperation are briefly discussed, followed by an outline of the origins ofalkalis in raw materials and fuels and of the published physicalproperties of relevant pure compounds.
Known physical and chemical factors affecting volatilisation are assessed- a key objective of this review. Finally, information on thedistribution of alkalis in clinker is presented, together with an outlineof initial attempts at theoretically estimating recirculating loads and ofpractically reducing their magnitude.
From the review it is concluded that there is general agreement on thefactors affecting the volatilisation of alkalis. Volatilisation isincreased by smaller nodule size, lower flux content in the clinker,higher levels of chloride, lower levels of sulphur, higher temperatures,longer heating periods and by higher contents of water vapour in the kilngases. It Is not clear what the effects of other factors are (over theranges studied in the available literature), and it may be inferred thatthese are relatively small: gas flow rate and composition, alkali content,presence of fluoride, LSF and S/R and oxidising conditions in the kiln..Several of these factors appear worthy of further study.
There is, nevertheless, insufficient quantitative evidence to predict thedegree of volatilisation of alkalis from a given raw mix under particularconditions. The interplay of phase equilibrium and transport phenomena isprobably too complicated for it to be worth while attempting to simplycalculate volatilisations from known thermochemical data: more complexmodelling is needed.
In practical terms, the circulation of alkalis is affected as much bytheir condensation and deposition as by their volatilisation. It would beuseful to devote some attention to this hitherto somewhat neglected aspectof the phenomenon.
ALKALI VOLATILISATION
A REVIEW OF LITERATURE AVAILABLE IN 1977
C O N T E N T S
1. INTRODUCTION
ISTN S7/4
Page Nr.
1
2. EFFECTS OF ALKALIS 3
2.1 Effects of high alkali levels in clinker
2.1.1 Alkali-aggregate reaction
2.1.2 Air-setting of cement
2.1.3 Effect on strength
2.2 Effects of high alkali levels on the manufacturing process
2.2.1 Effect on kiln fuel consumption
2.2.2 Corrosion of refractories
2.2.3 Build-up and preheater blockages.
3. SOURCES OF ALKALIS
3.1 Alkalis in limestones
3.2 Alkalis in clays and shales
3.3 Alkalis in fuels
3.4 Methods of reducing alkali ,zontents of materials
4. PHYSICAL PROPERTIES OF ALKALI METAL COMPOUNDS
5. FACTORS AFFECTING VOLATILISATION
5.1 Physical factors
5.1.1 Nodule and particle size
5.1.2 Effect of the liquid content of the clinker
5.1.3 Gas flow rates
5.1.4 Duration and temperature of heating
a
11
12
Cont./...
-ii-
N r .Page
5.2 - Chemical factors
5.2.1 K20 and Na20 contents
5.2.2 Effect of chloride and fluoride
5.2.3 Effect of SO2 and SO3
5.2.4 Effect of water vapour
5.2.5 Alkali containing minerals
5.2.6 Effect of LSF and SR
5.2.7 Effect of kiln atmosphere
6. DISTRIBUTION OF ALKALIS IN CLINKER
7. ALKALI CIRCDLATION IN THE KILN SYSTEM
7.1 Estimation of alkali circulation
7.2 Reducing alkali circulation
7.2.1 Removal and treatment of flue dust
7.2.2 Bypasses on preheater kilns
7.2.3 Other processes for alkali reduction
8. CONCLUSIONS
9. REFERENCES
2 8
31
4 0
10. NAME INDEX TO REFERENCES
11. TABLE 1
ISTN 87/4
ALKALI VOLATILXSATION - A REVIEW OF LITERATURE AVAILABLE IN 1977
1. INTRODUCTION
The following report summarises published information available
in 1977 on the subject of the behaviour of volatile alkalis in
cement clinker manufacture.
.These materials are distinguished from other clinker-forming
materials by being solid at the lower temperatures encountered in the
kiln system but vaporising at higher temperature - for instance in the
kiln burning zone. The effect of this is that they circulate within
the kiln and preheater system and can, under.certain circumstances,
attain high concentrations. The quantitive effect on alkali levels in
the clinker on removing some of this recirculating material by a
by-pass may not be immediately predictable.
Together with the compounds of the alkali metals sodium and
potassium, it is also convenient to consider other compounds involving
sulphur, chlorine and (less commonly) fluorine, which have boiling
points within the same range and which can exhibit similar behaviour.
Interest in the behaviour of alkalis in cement manufacture first
arose in connection with the possibility of obtaining potash for use
as a fertiliser from clays, feldspars and other unconventional
materials (I). A considerable amount of work was done on this topic
in the United States during the First World War, as at that time most
of that country's supply of potash was imported from Germany. In this
application, it was necessary to ensure that as high a proportion of
the potash in the raw feed as possible was volatilised and recovered
in the flue dust, and that this potash was water-soluble: this latter
feature could be achieved by heating in an oxidising atmsphere (2).!
This m&hod of producing @ash was uneconmic when ample supplies of
potashwereavailable fromother sources andsomrkwas discontinued
after the early 1920's.
The problem of alkali levels in CempJls was once mre brought
into pmninencewheh it was suggested (3) thatcemants withhigh
alkali levels reactedwith certainaggregates, suchas scxw chertsr
shales and limestones, to produce destructive -ion- This led
various national specifying authorities to limit the alkali content of.
cementS, ark3 so it was necessaryto investigatein5ms of r&uciqg
levels present. In the 1950's, the use of the suspension preheater
for dry process kilns intr&ucedfurther problems as alkalis are
recirculated within the kiln/prehsater system quite efficiently, so
t&&clinker alkali levels cxnnotba reduced simplybydiscardingthe
flue dust (which rarely &ibits a separately-collectable fraction
rich in alkalis). FurLher, the high levels of recirculating alkali
salts tend to condense at critical pints in the system and create
build-ups. This high level of recirculation can be reduced (with soma
increase in fuel qmsuqtion) by bleeding off sune of the gas from the
kilnbackendanddiscar~ngtheassociatedltustburden. Thedegree
of bleedrequiredto produce given results cannot always be predicted
accurately.
Research has been undertak~~atvaxious establishuents, with the
aim of constructing a theoretical model for alkali behaviour in
kiln/preheater system and devising laboratory tests which can be
applied to raw materials to predict their behaviour in large scale
kiln systems under various circumstances. Possible areas for such
research are identified in the course of this review.
2. EE7?Ems OF ALKALIS
2.1 Effects of high alkali levels in clinker
2.1.1 AUcdli-aqqreqate reaction
It was found by Stanton in 1940 (3) that cracking in concrete
structures couldbeattributedto reaction betweenalkalisinthe
cemant and certain minerals in the aggregate, This phexxxmmn wds
investigated by a number of organisiations, notably the US Wrreau of
Reclamation (41, frcm which it became apparent that the problem had
occurred with aggregates containing amorphous or microcrystalline
silica. Examples of such aggregates are opaline cherts, siliceous
shales and limestones and scma types of andesite, rhyolite and
obsidian (5). As a result of this work it becama standard practice in
theUSAto specify a rfaximm value of 0.6% by weight for equivalent
Na20 content (Na20 + 0.658 K-20) for the cement to be used with such
aggregates. This limit was intrcxluced as a tentative revision to the
ASIM standard for cemant in June 1959 and in subsequent versions
(e.g. 6) it is included as a characteristic which can be specified by
the purchaser if he considers it desirable.
The mst serious alkali-aggregate reaction problem were found
in the USA- mainly on the West Coast and in Nebraska and Kansas.
Reactive aggregates were also found in North Germany
(Schleswig-Holstein) and Denmark (71, but flint gravels found in
Germany and the UK have not generally been considered to be reactive.
Alkali-aggregate reaction is also known to occur occasionally in other
countries, e.g. Portugal and New Zealand (8).
Alkali limits are included in the standard specifications of
some countries. For example Brazil (91, Peru (lO).and Venezuela (11)
followed the ASTM in setting an optional limit of 0.6% for (Na20 +
0.658 K20) where a reactive alkali is expected, and Mexico (12) has
set limits of 1.2, 0.9, 1.2, 0.8 and 0.9% for Types I, II, III, IV and
V cements reapectivsly, with an optional lower limit of 0.6% for use
in concrete with reactive aggregate.
It has, however, been suggested (13) that alkali contents below
0.6X, perhaps as low as 0.35X, can still lead to reaction in some
circumstances.
Potash and soda generally have an equivalent effect in causing
expansion (7) but under some circumstances (14) it appears that more
potash than soda can be tolerated without expansion.
The form of the alkali does not seem to make a great difference
(13) in the long term, although water-soluble alkali is liberated more
rapidly from crystalline than from glassy alkali-containing phases in
early stages of hydration. It is suggested that the significant
factor appears to be the concentration of hydroxide ions in the pore
solution (15).
2.1.2 Air setting of cement
Rapid air-setting of c-t in storage is due $ the' formation
of syngenite (X2SO4.CaS04.H20) (16, 17) and thus it is generally
desirable to keep the K20 level in the clinker as low as possible
where other factors indicate that air-setting-may be a problem.
2.1.3 Effect on strenqth
It appears to be generally accepted in the literature that, at
levels typically found in cm-e&s , increasing the aUcali.contentof
the clinker tends to increaseearlystrengths anddepress ultimate
strengths. Forexample,AS?Mtestson2in.~~cubesgavethe
following results for cemnts with different soluble K20 contents (and
similar levels of potential C3S, C3A and fineness) (18):
Cartpressivestrength at
Cexnt with Carwtwith0.03% soluble K20
(MPa)0.61% soluble K$
@Pa)
1 &Y 8.41 9.79
3days 17.58 18.34
7day-5 27.72 24.41
28 days 45.09 32.41
The sama investigation found, however, that clinker fran which
the alkali (0.57% Na20 equivalent, minly as potassium salts) had.been
remved by reburning with ammniumchloride had lowx strengths atall
tinkas thahthe samcemantreburned ina similarmannerwithoutNH4Cl_.
addition. DatxlreportedbyMussgnug (21) ix-ldicatedthestrengthof
high-alkali clinker as being 100% greater than that of low-alksli
clinker atlday, 2O%greater at3 days and similar at7days and
subsequently. These findings were basedon tests co alargentznber of
clinkers withalkalisulphatecontents beW Oand4.0%
2.2 Effects of high alkali levels on the manufacturing process
2.2.1 Effect on kiln fuel consm@ion
The evaporation of alkalis in the burning zone consums heat at
high mature, which is subsequently liberated at a lmer
Mature. Additionalfuelisrequiredtomaintainthesamburning
zone temperature under these conditions, and Weber (22) estimates thad
this can be up to 31 kcal/kg of clinker for a specific suspension
preheater kiln,12 kc&/kg for aIqolkiln and 5 kcal/kg for awt
process kiln, the difference being explained by the opportunity for
effective use of the low-grade heat liberated in each mse.
EIowever, this fuel penalty my not be realised in practice,
because the presence of alkalis will tend to pramte the fornation of
clinker minerals atalowar temperature, thus permitting the burning
zone temperature to be reduced, other things being equal (19, 20).
2.2.2 Corrosion of refractories
Thamstserious adverse effect of alkalis on kiln linings is
said not to be cWcal but machanical (23, 24, 25). AlJ6i.i salts -
notably K2SC4 and Kc1 - condense on the brick at teqeratures of
700-10bO"C and fill the pores, thus increasing the risk of cracking
and spalling with temperature changes. In a kiln used part of the
time for the nanufacture of white cemaht under reducing conditions, it
was found (261 that sulphides, e.g. KE'eS2, me deposited on the
brick. Although the sulphides did not damage the brick and possibly
even tended to strengthen it, under oxiding conditions theywere
converted to sulphates with highly deleterious results.
2.2.3 E?uild-up and preheater blockaqes
The volatile ca-qounds evaporated in the burning zone tend to
recondense on dust particles and in the cooler parts of the kiln
system. There my ba a considerable teqerature range in tiich these
canpounds are in the liquid state (see Section 2) and in parts of the
kiln system in this temperature range, severe build-up problems can
OCCUT. Places where this happens axe the inletendof the kiln and
the preheater cyclones (271, in which coatings can lead to much
impaired flow of materials and ultimately complete blockage (28).
"Rule of thumb" limits have been quoted (29) of 0.015% for chloride
and 1.0 for the mlecular ratio of sulphate to alkalis in the raw mix.
Although clogging problems are widespread with suspension preheater
kilns, it has boer~ claimed thatshaftpreheaters are notsubjectto
them (30).
3. souw=Es OF ALKALIS
3 . 1 Alkalis in limestones
Innormal cases,publisheddata suggests thatthelimastone in
the raw mix is only a minor source of volatile carpounds. Average
values for 345 American limastones are (31):
K20 0.33%
Na$ 0.05%
=3 0.05%
Cl 0.22%
Anumber of Lkrbyshirelimestones had higher SO3 contents~ in
the range 0.1 to 4.8% (32).
One~uld~alkaliproblems tobecanali.kelywhenusing
calcareousmai%rials of marine origin, such as coral andaragonite
mud. Suchmaterials are used in Hawaii and the southern UnitedStates
(33) for ewmple, but as far as is known no particular problems due to
high sodiumchloride contents are encountered.
Inecpdments carried outatawet-prccess xorks where sea_water was used to-h oyster shell rawmaterial and tom&e uq the
raw slurry (341, it was found that substitution of fresh water
decreased the Na$ levels in the clinker to scene &xx-k but also
increased the K20 content, so that only a sr&l reduction of total
alkalicontentcould be obtained in this way.
3.2 Alkalis in clays and shales
These mterials normally provide the bulk of the alkalis in the
raw mix. Minerals with high alkali contents include feldspars, for
example orthcclasewhich can contain I+ to17% X2Oand albitewhich
can contain up to12% Na2O,andclayminerals, such as micas and
illite (35). Analysis of 33 illites (36) showed a range of Na2C
contents.frcxn 0.05 to 1.05% with a maan of 0.27% and X2C contents fran
4.6 to 11.0% with a mean of 6.7%.
3.3 Alkalis in fuels
Coals contain alkalis both in themineralmtter,~~andX~
together forming 1 to 6% of a typical British coal ash, and a.s sodium
and potassium chlorides, either in the free stateor adsorbed on the
coal stitances. Chlorine levels can be up to 1% ;37). British coals
are typicallymlow in sulphur, as arecoals franthewastem United
States, and Ruhr coal contains about 2.8% So3 (35). Eastern LE coals
are higher in sulphur as the following analysis (%'by weight of dry
coal) confirms (38):
Illinois coal
w 0.15%
Nazo 0.12%
=3 10.48%
Cl 0.22%
(Ash 9.58%)
It has been suggested (39) that coal my contain iodine which is
found in flue dust, but this muld not ha expected to have a
significant effect.
Heavy fuel oils, for ewrrple No. 6 Fuel Oil Bunker C) include
about 1% of water containing dissolved salts,‘mainly sodium chloride,
so that atypical ashmycontain 32%Na20, ckesponding tocontents
of up to about 0.1% of the oil. Sulphur levels can be high, ranging
frcxn about 2% (SO31 for a low sulphur oil with 0.04% ash to 10% GO31
for a high sulphur oil with 0.02% ash (40).
Natural gas contains no alkalis. Sulphurlevels (mainly in tbe
form of H2.S) can ba quite high in the raw gas, but pipeline
specifications generally limit H2S contents to 4 ppxn by voluma to
avoid corrosion, so that rmst of this is removed (41). (4~ by
volume of H2S corresponds to about 18.6 ppn by weight of S03, or about
0.0015 g SC3 per 1000 kcal).
Wastemterials usedas fuelcouldcontain appreciable
volatiles, depending 'on the sour&. . Addition of chlorinated
hydrccarbon waste to fuel has keen proposed (42) as amans of
reduciiq clinker alkali levels.
3 . 4 Methods of reducinq alkali contents of materials
It does not appear to be possible to reduce the contents of
alkalis in clays and shales by any practicable nmns. A series of
experiments by the Portland Cement Association (43) investigated
leaching, flotation and heating methods and showed that the only
mtl-&.5 to reduce the alkalicontentof the mterialappreciably ware
(a1 heating at a temperature and LSF approaching those used in cemant
manufacture and (b) heating with concentrated mineral. acid.
4. Pl-lYSICALPROPElRTIES OFALSAJLI MILTALCOMPOUNDS
Melting and boil& teqeratures (at 1 amphere) for scma
potassium; sodium and calcium cq&nds a.re given in‘&ble 1. SOUrCeS
for these are (40) and (441, except where otherwise indicated. It is
not'clear how significant these repours are under practical kiln
co&iitioti, since various eutectics form; for example in the
K2SO4/aSOq/I@1systemthelmest fusion teaiperatures are in the range
650-700°C (26).
VaqoU.pressures have been investigated fran an early date (47).
Fig. 1 shows saturated repour pressures of KCH, &OH, KCl, &Cl, KF
andNaF (40) together with approximate values for K2S04 (48) and
Na2sOq (49); these latter should be treatedwith scma caution as they
are ex%rapolated beyond the range of validity claimad for the
equations but should indicate general trends. For further details of
sadim chloride see (51, for potassium fluoride SW [SlJ and for
potassium and sodium sulphates (52). A considerable amunt nf wxk on
the behaviour of potassium sulphate at high temperatures has baen
carried out in connection with its possible use as a seed in
magnetohydrodynamic power generation (53, 54). &an calculation of
the partial presssures of the VazTious species present at teqeratures
in the range 1500-2000'K and 1 amphere pressure when
sulphur-ccntaining fuel oil is burnt, it appears that the potassium
ctxnpcunds present in significant quantities muld be K-$04,, K$O3
andKOH.
Althouqn me vapour pressures \Flg.ll agree v1 general. terms
with the order of volatility observed in practice, one muld
anticipate considerable difficulty in using them to predict absolute
volatilisation levels at given temperatures. Plbst of the species
involved do not cccur as pure canpounds in the solid state and
pressures andteqeratures inside nodules of clinker, for instance,
are not wall known.
5. FxxxxsAFFE13TINGvoLATILIs~IoN
By "volatilisation" we m3n the departure fran heat-treated
arterial of a proportion of a stitance originally present in a raw
llliX. This heattreatmtzntmayba under labratoryccnditions, in which
case volatilised stitances are generally r-v&l fran the system, or
i n tendto condense and ba
recycled,'giving a lowar
obtain~under different
care.
overall %xJ%e of
circumstances must
5.1 Physical factors
5.1.1 Nodule and particle size
vclatilisation". Values
therefore be carpared with
It muld be expected that under certain conditions the rate'of
loss of volatile suketances from nodules could be limited by their
diffusion frcm the interior of the nodule to the surface. Experiments
by the-FCA with various sizes of nodules of raw mix and with rebmning
clinker nodules of various sizes tend to confirm this' idea (551,
althouqh the author suggests elsewhere (56) that in practice the
effect of nodule size my be small in cmparison with factors such as
temperature and residence~tima at-mature. This view is supported
bv a series of statistically-controlled experiments at NIIITsenrent
(57). Results of Goes Ad Keil (58) and Draper (55) have been
replotted on a lag/log scale (Fig.21 and agree (with the exception of
one value for lmn pellet diameter), indicating a relationship of the
form:
volatilisationd 1
.3'dJ-
Analysis of pieces of clinker of different s&as (59) showA K20
levels to be higher & the larger pieces.
Although it appears that the effect of nodule size on
volatilization is not very great in practice (for example, a variation
in pill size of f 25% would alter volatilisation by C 7.5% - lo%), it
could nevertheless be useful to investiuate it more thoroughly, both
to verify the relationship, which is based on very limited data, and
as a guide to the factors limiting alkali volatilisation under various
ccxnbinations of burning tirre and temperature.
Scma mrk has been &ne with beds of poxdered raw mterials of
various depths (55, 591, the results of which broadly parallel those
for nodulised raw mterials. No publications dealing'with the effect
of the size of individual particles on volatilisation have been found;
it seems reasonable to propose that below a certain size this muld
have little effect but it muld be useful for stamlardising
-imental results to put this ptulate to the test.
5.1.2 Effect of the liquid content of the clinker
Since the effect of increasing the liquid content is to reduce
the porosity of the clinker, this factor would be expected to lower
the rate of alkali volatilisation (58, 60, 61). Mussgzmg, howaver,
found no correlation baMaen total alkali (KS + Na$) and Fe203
contents of a number of clinkers (211 anda separate series of
experim31.ts showed that the A/F r‘t'a 10 was the least significant -of the
five factors studied (571, being overshadoWed by temperature, time,
sulphate content and pellet size. Itwmld'te of interest to
investigate the magnitude of this effect in store detail, as there
appears to be scrne disagreeman tas to its iqortance.
5.1.3 Gas flow rates
The effect of gas flow rates on the volatilisation of alkalis
has been studied to a limited extent only, for example by Jackson and
Morgan (621 who detected ho significant variation. I&oratory
vimants on volatilisation rates scmatimas incorporate means for
passing a gas canposition approximating to kiln gas over the raw mix
(551, for instance 77% N2, 20% CO2 and 3% 02 (56). So2 (see Section
4.2.3.) and water vapour (Section 4.2.4.) have been added to this.gas
in varying quantities, but no results of altering its flow rate have
been found. It is possible that this could be significant in saz. -cases, as significant variations in volatilisation with stirrins a bed
of powder have been reported (59).
5.1.4 Euration and temperature of heating
There is general agreemant that the degree of volatilisation
increa.%es with the tim andwith the Mrperature of heat treatment,
although it has been noted (60) that after heating fran 700°C to
14OO"C, little additional volatilisation takes place on subsequent
heating at 1400°C for a further 30 minutes. The effects of duration
and teqerature are thought to be highly significant and about equal
in rnagni.tGde (57).
The rate of volatilisation frcxn a particular raw mix under gives
temperature andother definedexternal &hditions has not been
investigated, buts- interesting conclusions can be drawn fran
additional analysis of reported data.
An assumption which is widely made, albeit usually implicitly,
is that the proportion of a species volatilised on heating for a given
time and at a particular temperature is characteristic of the raw mix,
i.e. that the volatilisation rate is proportional to the amunt
present (a). Thus:
-da=kadt:
- a0 r 1h = orkdfa-
a t J t I
In (at) = -kt(a,>
where at is the amount of alkali present at.time t and a0 the amount
present at the start of heating. If this assumption is correct, that
is, if the volatilisation reaction is first order with respect to K20
or Na20 content, plotting the log of the amount of alkali remaining
against time should give a straight line. Data from Palmer and
Baylees (34) and Woods (63) were analysed in this way and results for
selected mixes are shown in Fig. 3. It will be noted that although
the fit is very good in most cases, the line of best fit does not
always pass through the point corresponding to 100% original alkali
content at time t=O. To explain this, it is necessary to consider t
heating conditions which were applied. In (34) the samples were
heated for 20 minutes at 1800°F (980°C) to decarbonate kthem and
immediately transferred into a high-temperature furnace maintained at
2600°F (1427"C), in which they were keept for the appropriate length oi
time. The heating programme in (63) is not stated. In the case of a
predicted initial alkali level substantially below 100X, a possible
explanation is that part of the alkali is driven out while the sample
is being heated up to the experimental temperature. This appears to
be reasonable, although it is surprising that, if this is SO, no
correlation was found between the rate constant k and the initial
alkali level ao. This could be due to the presence in the mix of
chloride levels appreciably less than those needed to react with all
the K20 (the addition of chloride is known to increase volatilisatic
significantly - see Section 4.2.2.). The line shown for Mix 12 of
(34) with added CaC12 shows a very low level of K20’ remaining at the
start of heating at 1427"C, and a rate constant which, although the
highest of those observed, is not much higher than that of the same
mix without CaC12 (not shown in Fig. 3), - 0.0820 and - 0.0771
respectively. In the latter case, however, no volatilisation appeared
to have taken place at lover temperatures.
Another problem is presented by results such as those for Mix 5
of (34) and Mix 3564, 125O"C, of (63). In these cases, it appears
that volatilisation does not begin until some time after the start of
heating at the final temperature. In the case of Mix 3565 of (631, no
K20 volatilisation takes plz&e at llOO"C, at 12OO'C it begins only
after 60 minutes, at 125O'C it begins after 30 minutes and at 1300°C
and higher temperatures it starts immediately. This delay is perhaps
due to the alkali-containing materials initially requiring to react
with other components before the alkalis are released.
The correlation coefficients were recalculated in selected cases
including the point a = 100X;, t = 0. As would be expected, the
correlation was usually slightly improved where the original line of
best fit passed near this point, but where significant changes in k
and/or a0 resulted, the effect on the correlation was unpredictable.
It vould therefore be desirable to carry out experiments on the rate
of volatilisation, in which the actual alkali contents at t = 0 are
measured. If the relation suggested by the data already examined was,.
confirmed, this would mean that the proportion of alkali volatilised
under given conditions was independent of the absolute amunt present
(until; of course, all the alkali was lost).
An alternative way of indicating the propensity of a raw mix to
lose alkali on heating has been proposed by Palmar and Rayless (34).
This is the "resistance factor“ which is the sum of the percentages OI
alkali remaining after heating for 10, 30, 50 and 70 minutes at 2600'F
(1470°C). This empirical mathod appears to be suitable for cuqar'i3-g
raw mixes with each other, but does not permit the prediction of
volatilisations under other conditions. Its use has not been taken up
by other mrkers.
Maintaining clinker atan elevated temperature has been used as
a n&hod of reducing its alkali content (64, 65). A tE Bureau of
Reclamation specification for low heat, low alkali cement was ntet by
reheating the clinker frcm the kiln to 1427°C in a converted rotary
cooler- Na$ equivalents decreased frcm 0.889 to 1.19% in the
(loss-free) raw mix to 0.411 to 0.890% in the clinker and to 0.315 to
0.716% in the treated clinker. The heat input to the clinker treater
was abxt550 kcal/lq clinker,which renders themathodunattractive
in nomal circmnstances.
Data obtained by the Portland Cement Association (56) for a
number of kilns show that total alkali volatilisation tends to
decrease as the residence time of the mterials in the burning zone
decreases, but the effect of other factors is tcogreatto permit a
quantitative analysis.
The effect of mrature on volatilisation is canparable in
magnitude to that of tine (51). It has been stated that "the burning
of cement clinker takes place within a temperature range where a
canparatively small rise in the temperature will cause a noticeable
increase in the amount of alkalis volatilised" (66). It is therefore
said to be necessary to control the burning zone temperature
accuratfAy. Itcertainlyseems to be the case that there is a big
increase bet- ll.50 and 13OO'C (particularly bat- 1200 and
1250°C) in the percentage of the original K20 volatilised in one hour
(591, although in normal conditions one would expect rmst clinker
reach these teqeratures in a kiln. Kate constants have been
calculated fran the data of Wads (63) at a range of matures
to
f o r
K20 and Na20 volatilisation frcxn one raw mix and these are shown in
Fig. 4. The rate constant increases roughlylinearlywith
temperature, the effect of tgmperature being much more significant for
K2Othan for Na20. Itmightbeexpe&ed fromtheorythatlqeK~uld
be proportional to l/T ("K), but the limited data available do not
appear to confirm this and further exp~imznts muld be desirable.
The increase in K$ volatilisation in a given tima with temperature.-follows a logistic curve (591, since the absolute rate of
volatilisation after a given tima initially increases with temperature;%
(as the effect of the increase in kwith temperature wthe daninant
factor) and then declines again (as the amount of alkali remaining
becomes the dxninant factor).
'i>- ta ure at which volatilisation begins can be as low as..
700-800°C for El (21) but is rrore typically in the region of 1100°C.
5 . 2
The volatilities of the various species are discussed in mre detail
below.
Chemical factors
5.2.1 KS and Nag contents
It has already been suggested (in Section 4.1.4. above) that the
kinetics of alkali volatilisation are first order with respect to RIO
and Na$, and if this is the case the percentage volatilisation is
independent of the absolute levels. Hcmever,dataobtainedbytheFa
(67) suggest that reduction in alkalis in fullsize kilns increases
with alkalicontentof the rawmix. These findings are not
necessarilycontradictory,as clays andshales withhigher K$and
Na$ my, for ample ,contain thein inaless firmlyminbined form,
lost at loam temperatures, but this is certainly an area which xmld
repay investigation.
As far as the relative volatilisation of Na$) and K20 is
concerned, it appears (56) that volatilisation of Na20 is negligible
where Kg volatilisation is less than 30%, and is at about half the
level of additional K20 volatilisation above the 30% "threshold".
5.2.2 Effect of chloride and fluoride
The early studies on the recovery of potash fran cement flue
dust and other minerals (62) showad that the amount of KF volatilised
under given conditions could be increased by addition of calcium or
sodiumchloride. Itwas found to be~necessary to add just over the
quantity needed to combine with the K20 to give KCl. NaCl was rather
more effective in promoting volatilisation than CaCi2. With the
interest in reducing total alkali in the clinker, the effects of NaCl
and CaCl2 on Na20 volatilisation also were investigated, and Woods
-(63) found that although NaCl was indeed more errective in liberating
K20 than was CaC12, the Na20 content of the clinker was noticeably
increased by NaCl addition. The use of calcium chloride was studied~
in full size kilns by Holden (68), who found that the removal of
alkali by addition of calcium chloride could be estimated for CaC12
additions up to 1.5% by the empirical equation:
0.559 K, [CaClZIAr f 100 - L
where A, * total alkali removal expressed as Na20, K, = apparent
efficiency of utilisation of CaCl2, L = loss on ignition of raw
material and [CaClz] = % of CaC12 added (dry basis). The efficiencies
of CaCl2 utilisation observed were 27% to 34% (average 32%) for wet
process kilns and 45% to 56% (average 48%) for long dry process kilns.
Addition of 35% commercial grade hydrocholoric acid has been used as a
cheaper alternative to CaC12 where this was not readily available
locally (69). No particular problems were encountered in adding the
acid to the slurry tanks and control of the quantity added was better
than when flake calcium chloride was used.
Problems have arisen with low volatilisation and build-up
problems when CaC12 is used in long dry process kilns(70). Although
no published data are to hand, it would be expected that levels of
chloride addition would cause severe problems in preheater kilns and
muld probably have little effect on alkali reduction.
Contrary to the above results, laboratory tests on smrrles man
six works in Central Asia (71) showed that addition of NaCl did not
appreciably increase and inmstcases reduced the Na2C1contentof the
clinker, but that CaC12 was in rmst cases more effective than NaCl.
Although it is known that addition of chlorides decreases alkal
contents, further mrk needs to be Qne before the precise effect at
various temperatures can be predicted.
Eata on the effect of fluorides on alkali volatilisation are
spar=. woods (63) states that where calcium fluoride was added to a
raw mix to produce a high early strength cerrwt, the clinker mntaine
less potash than usual butahoutthe same amount of soda. He suggest
that addition of CaF2 &uld probably only be of value in pramting
volatilisation where the raw mix was high in KS but relatively ion i.
Na20. According to Sprung and van Seebach (721, theremdymmic
considerations favour the formation of calcium fluoride and alkali
matal sulphates rather thanalkali fluorides andcalciumsulphate.
The amunts of fluoride in rawmaterials are, however, small in mst
cases. Cost and possible toxicity muld probably make fluoride
addition unattractive as a means of increasing alkali volatilisatior
even if it were mre effective,
5.2.3 Effect of So2 and So3
The water-soluble alkali salts remaining in clinker are almst
entirely sulphates (16), chlorides having been lost through
volatilisation. The effect of sulphur compounds 0; the alkali content
of the clinker is therefore considerable, the sulphur deriving both
from the fuel and from sulphur compounds naturally occurring in (or
added to) the raw materials. The sulphur content of the clinker is
typically 50 to 65% of the total sulphur input from all these sources,
so that it is possible for the sulphur content of the clinker to be
higher than that of the raw feed (22). As the vapour pressure of
alkali sulphates is considerably lower than that of chlorides (Fig.1)
it would be expected that higher levels of sulphur in the clinker
would tend to prevent alkali volatilisation and this is in fact
observed (54, 56). The effect on K20 volatilisation is appreciably
greater than on Na20 volatilisation (62). K20, Na20 and chloride
contents of flue dust are reduced even in the presence of chloride in
the feed (73) - which can be advantageous in improving the efficiency
of electrostatic precipitation - so, it would seem, demonstrating that
alkali sulphates are formed or retained in preference to the more
volatile chlorides and oxides. Statistical examination shows that
SO3 content is second in importance only to time and temperature in
affecting alkali volatilisation (57). Operating data (56) from ITS
kilns show a relation between volatilisation of SO3 and K20, although
it is not clear what is the significance of this and there is some
evidence (56) that the effect of SO3 is greater at higher
temperatures. The equilibrium between calcium sulphate and CaO, SO2
and SO3 has been extensively investigated. At temperatures above
lOOO”C, combustion of sulphur compounds in the fuel results
predanhantly in SC2 (271, which can react with lime in the
temperature range 600-900°C.
34 CaO + 4 SO2. . 3 CaSO4 + CaS
The xraximum absorption of SC2 by raw meal was obtained at 880°C;
this is significant since a high proportion of the sulphur in the kiln
exit gas can be absorbed by raw meal in the preheater (74). Snaller
amounts of sulphur can also be absorbed byrawmterials, where these
are dried by kiln exit gases in the rawmill.
The decaqosition of pure C&O4 begins at about 900-lOOO'C, but
is initially very slow. Sax5CaSC4remainsunconvertedatabout
1385“C, which is the melting point of the CaO-CaSO4 entectic (75).
The decaqosition rate is much increased by the addition of other
materials, eg silica, alumina, kaolin and iron odde, and by the
presence of water vapour. -sition is also faster in a reducing
atmosphere, when CaS is formed. This fact has been used in processes
for mmfacturing cen?ent and sulphuric acid, by heating a mix of
anhydrite, coke and argillaceous materials in a rotary kiln (76).
- 4
3 - 4
+x +m2+cas
+c&-+4c.&+4=2
The lime reacts with the argillaceous ccqxxents to give clinker
minerals and the SC2 is separated fran the exit gas. It is necessary
to maintain oxidising conditions in the exit gas to avoid the
formation of elemental sulphur, for instance by reaction of the H2S
andSO2. It has been claimed that low-alkali ceinentcanbeproduced
in this prccess by adding calcium chloride in the usual way (77).
This 'is perhaps unexpected in view of the effect of even a small
percentage of added calcium sulphate on alkali volatilisation, and no
doubt results from dissociation of the CaC12, allowing alkalis to
evolve as chlorides.
Further mrk on this aspect should investigate in greater detail
the effect of varying levels of sulphate addition at various
temperatures and in the presence of other materials; also, the
relative effects of So2 in the kiln atxmsphere and calcium sulphate in
thefeed.
5.2.4 Effect of water vapour
Fran the relatively high vqxmr pressures of KOH and NaOH it
might be exqected that water vqour +muld pramte volatilisation and
this is confirmed by laboratory expariments by Goes and Keil (581,
which gave the following results
H2OiIlkilngas
% byvol.
0
5
1 0
K20 volatilisation with 30 min at
1330°c 14OOY% %
6 4 83
76 100
100 n.d.
Wcods (70) reports that satka works have claimad that spraying
small Zn-ounts of water (approx. 2ml/kg clinker) into the burning zone
directly above the flame my reduce the clinker alk$i content by
-0.1 to 0.2% (on clinke?z). This effect might have sme relevance to
the observed tendency for gas (andperhaps oil-fired) kilns to have
higher alJcali volatilisations than coal-fired kilns (18, 54, 65) since
more water vapour muld ba produced by ccanbustion of hydrocarbons.
(Spiers reports moisture levels in canbustion products as:
2 - 5% coke
10 - 15% Lignite
7- 9% coking coass
5 - 7% Anthracite
1 0 % - H.F.O. 1
5.2.5 Alkali-containinq minerals
Scdiumandpotassiumin rawmterials can occur ina number of
different minerals (see Section 2) and these can vary in their
tendency to lose alkalis (57). Elpertits with rawmaals containing
mica, illite and orthaclase feldspar (58) showad that alkali w lost
mre readily fran mica and illite than from feldspar at temperatures
of 900-1250°C. It is suggested that this my be due to difference in
bond energies for the various minerals. Another factor may explain
differences between minerals; for example in greensand (glauconite)
the silicate is hydrated, (62) leading to formation of K20 in the
presence of H$ when heated, allowing the formation of Koti, tiich has
a higher vapour pressure than KS. (see 4.2.4.)
It muld be useful to investigate the response to heat treatmant
of various potash and scda containing minerals in mre detail, and
this muld require sama a-cans of allowing for the effects of other
factors and also devising a quantitative msasure of the "availability"
of K2OandNa20 in theminerals.
5.2.6 Effect of LSF and SR
Although little reliable infomtion on this subject has been
found, such as there is indicates thatitwxld be useful tocarryout
further Czq&nmts. Ekperirrwts on remving alkalis frcmraw
materials by heating (43) indicated that there was no mlatilisation
on heating mixtures of clay or shale with 10% or less of limastone to
fusion and that alkalis wsre not released in significant quantity
until the amuntof lime approached that of a normal cenwt raw mix.
The data are shown in Fig. 5 where percentage loss of alkali is shown
in relation to the proportion of CaC03 in the mix, and in Fig. 6,
which shows alkali loss in relation to the TLSF - which has been
estirrated since the caqxxsition of the shale was not reported. It
will be seen fran these figures that the proportions investigaM do
not permit us to say whether ease of volatilisation varies with LSF
within the range normlly found, or whether aminimumlima content is
required, above which there is little variation. Earlier experiments
(62) had shown that KS could be volatilised frm greensand
(glauconite)/l~stone/cdlcium chloride mixes containing as little as
one third limestone, if these were heated to temperatures just below
that of fusion.
The effect of silica ratio on alkali volatilisation has not been
investigated. Tbare is scma evidence (68) of a higher, calculated c3S
content leading to lowar alkali levels in clinker, and it ms found
(61) that clinker alkali levels could ba reduced by replacing part of
the argillaceous mterial with sand. Howevex, in this case the effect
of increased S.R. was not distinguished fran the effects of lmer
alkali levels in the sand reducing &-se in the raw feed and the
necessary higher burning matures, which one wuld expect to ba
more significant.
5.2.7 Effect of kiln a-here
In normal centant cperations, as distinct fran the
cment/sulphuric acid process (see 5.2.3 above), the limited
frm laboratory tests (59) suggests that
greatly affected by the kiln amphere. The
a reducing amphere pramtes volatilisation at
perhaps slightly depresses it at 13OO"C, but the
information available
volatilisation is not
results indicate that
1200°C and 1250°C and
data do notreallyperm.ituseful conclusions to be drawn.
FundamantaJ.ly,a reducingatmxiphere is expectedtoprcm&e
volatilisation of alkali sulphates in the burning zone.
6. DISTRIEUTIOJJ7OF~SINCLIN?GZR
The distribution of alkalis is not revie++ed in detail, as the
literature on this subject is very extensive.
E'rcm the efforts to utilise flue dust during the First World
War, it had been noted (78) that potash in flue dust existed in
several different forms with different degrees of solubility in water
or acid, but no substantial progress k~s made until the 1930's and
1940's, when ah extensive programe of mrk GELS carried out at the
(US) Natioml Bureau of Standards, in cooperation with the Portland
Cement Association (79 - 84). Newkirk (85, 86) concluded that the
alkali-containing compounds M&A3 andKC2jSl2ere unstable in the
presence of SC3 andCaSO4 and reacted to give an alkalisulphate phase
which xas imiscible with other phases. For R$/SO3 mlecular ratios
<I, the SC3 reactedpreferehtiallywith the KS. The alkalisulphati
phase is imzdiately soluble in mter (87) although alkali fran other
phases is not.
Segnit (881 suggested that at least some, and possibly a
considerable part, of the soda in Portland cemnt occurs in the C$.
On the other hand, investigations at the Bulgarian Building Research
Institute appeared to suggest that both KS and Na-$ are predminantly
in the form of aluminates (89). Toropov and Dobrovolksky (60) support
Newkirk's opinion that most of the KS is in belit&; they excluded
clinkers with free alkali sulphate from consideration.
Pollitt and Brown (16) generally mnfirm Newkirk's findings on
alkali sulphates, noting that equilibrium conditions are not attained
in a kiln, so that works clinkers tend to contain mre calcium
sulphate thah do latxlratory clihkers. They also suggestthatscme
potash could cxcu~ in the C3A and that t&h potash and soda could
exist in alite in small quantities.
Azelitskaya and co-workers (90, 91) found that addition of
gypsum to raw mixes containing alkalis diminished t?ne effect of
alkalis, which (at a raw mix SO3 content of 0.6% or less) was to
decrease C3S content. With the addition of.5 to 10% gypsum to the raw
mix (which also raised the LSF and hence the C3S content), alkalis
were in the form of their sulphates. When investigating dust return,
Luginina and Shaposhnikova (92) found that the presence of high levels
of alkali sulphate tended to reduce alite formation and to give alite
crystals-with inclusions of belite and alkali glass and eroded edges.
Other work (93) confirmed that the addition of gypsum to
alkali-containing mixes tends to convert the alkalis to soluble
sulphates; in this work the optimum SO3 level in the clinker appears
to be about 4%.
Subsequent work by Abbassi (94) confirms the general trend of
previous investigations. Alkalis can exist in clinker separately, as
sulphates or carbonates, or in other phases: C3A dissolves soda
preferentially. However, all the phases can contain at least some
potash and soda, the amounts in the flux phase being below 0.2%. The
ratio of the K20 content of the C2S to that of the C3S is usually
about IO, the maximum K20 content found for C2S in this work being
1.9%. The Na20 ratio varies, but is about 10 for max. 0.6% for Na20
recorded in the C~S. More Na20 was found (relatively) in the C3A at a
max. of 1.7% (cp, 3.2% max. for K20).
7. ALK?GICIRCULATION INTKEKIINSYSTEM
7.1 Estimation of alkali circulation
Equations to give the concentration of a volatile cqnent i at
various points in the system have been derived by Ritmann for
Polysius AG (28, 95). According to these, in a system without a
bypass, the attmntof the ith caqmentrecycled frcxnthe kiln gases
to the incaning mterials (referred to as the adsorbed phase, since
this is believed to consist rtkainly of alkali carpounds condensed on
raw material particles) is given by
(Eli + Bri*) .ai.CiXi =
l- c2i.ai
ci represents the amount of the.cmponent in the raw maal
Bri* =Bri/Ci where Bri is the amount of the cmponent in the fuel
ffl i
5 2 i
ai
represents the volatilisation of i from the raw ma1
represents the volatilisation of i from the recycled naterial,
and
represents theextenttowhich the component is reabsorbed from
the gases in the preheater.
Note that Xi, Ci and Bri can be in any consistent units of ItaSS,
such as (but not necessarily) g/kg of clinker or per cent of clinker.
$li, f2i ad ai are fractions not percentages.
It is ~instructive to consider the assurrptions mde in deriving
this equation. If the various value& are shown in a diagram Ri is the
content of the ccmponent i in the clinker:
XiTar
Then if Xin and Xi(n-1) are the values of Xi after n and (n-l)
:ycles respectively:
Xin = Bri + Ci Eli + Xi(n-1) 2i
But in equilibrium conditions the amount of each component
circulating is constant,so that
xi = Bri + Ci Eli + Xi E2i-
ai
Xi s ai (Bri + cilli)
(1-a c2i >
or Xi 31 ai Ci (Eli + Bri*)
(1-a C2i)
.This assumes that the whole of the volatile component in the
fuel is volatilised and that no raw feed is lost to the stack (or
dumped) from the kiln/preheater system.
Using the same symbols and assumptions, it is clear that Ri (1
content of component i in the clinker) will be the amount not
volatilised, i.e.
Ri = (IL-&li) Ci + Cl-f2i) Xi. i
hence
Ri = (l-<li) Ci + (l-[*i)
= C i
(l-aiE2i )
E(l-Eli) + ai Bri" (1-{2;) f ai (<li-E2i II
If ws can neglect the volatile content of the fuel, for exaqle
for K20 and Nag if oil or gas is used, Bri* = 0 and
Ri = ci [ (l-Eli) + ai (Eli -czi) 1
(l-aic2i)
= Ci (l-Eli (l-ail 1( 7l-aiE2il )
If a fraction V of the kiln gases is by-passed, then the
volatile ccqonent i passing on to the preheater will be reduced to a
level Xi Cl-V)/ai, and the axrount recirculating will be Xi (1-V). We
can therefore represent the effect of a by-pass in the above equation
by replacing ai by a'i where
a'i = ai (1-V)
These assm@ions are cleiuly open to criticism. The concept of
differing volatilisations for raw mterial and recycled mterial is
swrted by soma qrtitalevidence (28) which suggests that
alkalis are rtore readily volatilised frcm recycled mterial than from
raw mterials, although other mrk (55, 59) indicates that alkalis in
flue dust are less readily volatilised than those in raw materials.
However, the values for any single ccqqent do not autamtically take
into account the amount of other components present. For example, the
volatilisation of KS will be. increased by the presence of chloride
and&creased by the presence of SO3. As these ccaqxments are lost
fran the system to different extents, the proportions in the
recirculating material willvaryas the system tends towards
equilibrium. Although the volatile content of coal ash is relatively
small, it is not necessarily all lost (96) and sma alkalis my reach
the clinker from this source. It is also possible that SO3 fran oil
fuel could be re-absorbed at relatively high ixqeratures. Ibere
seems no reason to assume that dust lost frcm the prekzker will
contain alkalifrcmnthekilngases only and thathoalkaliwill be
lost frcm the raw material (55). It appears that in practice the
factorsE1 a.udc2 are estimatedempirically in a particular case, so
that while these equations may be useful for predicting the effect of
varying the level of ah existing by-pass, for example, they muld
probably ba of little value in predicting the bahaviour of a raw
mterial in aproposed hew system.
Teoreanu and Puri (94) adopt different ratios which seem to be
less gene-rally applicable than those of Ritzmann. They &, hcmver,
intrcduce the possibility of non-equilibrium conditions in the kiln,
for instance where alkali-containing coatings build up over a period
and then break free.
It is clear that in addition to the factors affecting
volatilisation which have been discussed at scnte length abve, the
condensation and recirculation of alkalis are also important. One
mans which has been adopted for following alkali circulation is the
use of radioisotopes such as K42. Inanexperimantonawetprccess
kiln (981 it was found that the man number of cycles was about five,
the time for each being 110-120 minutes. This value is on the high
side, caqaredwith those derivedbycalculaticm frmalkalibalances
(99, 100). The efficiency of capture of dust by the preheatar system
varies according to the type. Ritmann quctes typical values for dust
collection efficiency for cyclone preheabars of 60-90% for stages
3 and 4 (1011. The total capture of alkali-ccntaining dust will
therefore be very high, and hence the alkali levels in'the flue dust
are very low (102) and the circulating load very high. & wet process
kilns a proportim of the alkali, say 40% of the KS (221, is
precipitated, and alkali levels in the flue dust are mderate (102).
The typical Le@ kiln (22) emits little dust and apparently traps
aln-ostno alkali in the grate: very high values have been reported
for the alkali content of the flue dust (22).
7.2 Reducinq alkali circulation
7.2.1 Rezmval and treatnwt of flue dust
Over a significant period of tima, the net gain of alkalis in
the kiln systmmustbe zero. Therefore, apart frm the small amunt
of alkali in the stack gas which is not precipitated in the dust
collectors, all the alkali put into the systemmustleave either in
the clinker or in the flue dust. Thus, it is only possible to reduce
the alkali level in the clinker to a level below that arriving in the
rawmeal if the flue dust is either dmped or treated to reduce its
alkali content before being returned to the process (55). In a wet
process kiln, discarding the dust reduced the equivalentNa20 in the
clinker fran 0.68% to 0.54% (68). As dust rermml will reduce the
amour&of circulating alkali, however, the rduction in clinker alkali
that can be achieved by discarding dust will be less than the alkali
content of the reamed dust.
Anumber of ways of treating the dust to reduce its alkali
contenthavebeenproposed. As the finer fraction contains a higher
proportion of alkalis (103,104) it should be possible to reduce alkali
circulation by returning only the coarser fraction of the dust,
although it is doubtful whether the differential muld often be large
enough to mke this procedure mrthwhile.
For reasons discussed above, there is a considerable variation
in water solubility of K20 between flue dusts, ranging in one study
(103) fran 2 to 96%. Because of this the efficiency of leaching
vaxies, but it has frequently baen used or proposed (105 - 108). I t
is obviously best suited for use with uet process kilns. Problerrs may
arise in disposal of the salt solution produced, as it is rarely
econanic to recover these salts as solids.
Another mans of reducing the alkali content of flue dust is to
heat it to, say, 1200°C. This can be done conveniently in a fluidised
bed reactor (109).
7.2.2 Bypasses on preheater kilns-
In preheater kilns - especially 4stage cyclone preheater kilns
-virtually all the alkalis in the gas franthe kiln are absorbed by
raw feed in the preheater. Thealkalicontent in the flue dust is
therefore very low and little reduction in the alkali content of the
clinker or in the circulatingloadcan be obtainedbyremving or
treating the dust. One way in which this could can be achieved is by
removing part of the gas and/or dust before it enters the preheater,
cooling it, collecting the dust and discharging the gas to the
a?mosphere (21). Problems tend to arise in practice with the txlild-w
of alkali. Although it muld be preferable to cool the gases by uater
spray, as the gas volumes needing cleaning are nmch less in this case,
there is so far little practical experience of this, ccoling by mixing
with cold air having been used in rmst cases (ll.0). It appea.rs that
the effect of a bypass is greatest up to about 20% bleed (991, above
which the increased fuel consumption, which is about 40 kcal/kg of
clinker at 10% bleed (211, becomes excessive in relation to the alkali
reduction obtained. Suggested bypass levels (ill) are 2-4% to reduce
operational problem, eg blockages, and S-15% to reduce alkali levels
intheclinke.r. A possible modification proposed to the bypass (112)
is to pass the bled-off gas through an initial cyclone and return the
coarse dust (with a low alkali content) direct to the kiln. Although
this means thatmre gas has to be bled off tomintain the same level
of alkaliremval, the quantity of dust to be collected is much less.
Incorporation of a bypass enables the maximum permissible
chloride content of the raw fe& (see Section 1.2.3.) to be increased
frcxn 0.015% to about 0.075% at 10% bypass (29). As wxld be -ted
the effect of
Na$. It has
itnaybecaae
volIxrrs of gas
a bypass in reducing K2Ois greater thau the effect on
baen sugges& that if high levels of bypass are needed
desirable to use a precalciner system (ll3, ll4) as the
passing through the kiln is thenmuch reducedandthe
increase in fuel consuqtion at high bypass levels (eg 50 to 100%) is
less important.
Although alkali problems are n-c&often eucounteredwith cyclone
preheaterkilns,bypassescanbeusedwithgratepreheaterkilnsdlso
(IS, IX). In this case, the cleaned bypass gas can be used for
7.2.3 Other processes for alkali reduction
Same alternative n&hods for reducing alkali circulation have
beenproposed. One of these (ll7, 118) involves using excess hot air
fran the cooler for drying pellets on a grate preheater. The kiln
gases~~dbepassedthro~htfiecdlciningpartof thegrateandthen
passed toa dust-collecting systemtogether with the cooler air which
hadbeen passed through the other part of the grate.
An alternative mathod of lowaring alkali circulation in
suspension preheater kilns which has been proposed (although not yet
used in practice) is to pass some or all of the kiln exit gases over a
cooled surface (ll9) to produce a deposit of condensed alkalis and
high-i dust. Possible modifications to this process include the
use of~water-cooledtubes or of bdies exchanged betwzn the kiln
system and a cooling/alkali remval plant.
8. CONCLUSIONS
From the review it is concluded that there is general agreement on thefactors affecting the volatilisation of alkalis. Volatilisation isincreased by-smaller nodule size, lower flux content in the clinker,higher levels of chloride, lower levels of sulphur, higher temperatures,longer heating periods and by higher contents of water vapqur in'the kilngases. It is not clear what the effects of other factors are (over theranges studied in the available literature), and it may be inferred thatthese are relatively small: gas flow rate and composition, alkalicontent, presence of fluoride, LSF and S/R and oxidising conditions inthe kiln. Several of these factors appear worthy of further study.
There is, nevertheless, insufficient quantitative evidence to predict thedegree of volatilisation of alkalis from a given raw mix under particularconditions. The interplay of phase equilibrium and transport phenomena isprobably too complicated for it to be worth while attempting to simplycalculate volatilisations from knoun thermochemical data: more complexmodelling is needed.
In practical terms, the circulation of alkalis is affected as much bytheir condensation and deposition as by their volatilisation. It would beuseful to devote some attention to this hitherto somewhat neglectedaspect of the phenomenon.
RRC/TGB/JLMC/D31:CPK/LEX3211.03.87:12.02.R8.
T. G. BURNHAM.
1.
2.
3.
4.
5.
6.
7.
8.
BUCK, E-C.: Bibliography on the extraction of potash frm complexmineral silicates, such as feldspar, leucite and glauconite (greeeandmarl).Metallurgical and Chemical Engineering, 1918, 18, (11, 33-37 and (21,90-95
MEG, A.R.: The directheattreatmntof cemntmill dust to increaseits water-soluble potash content.Journal of Industrial and mgineering Che&stry, 1918, 10, (21,106-109
STANKlN, T.E.: Expansion of concrete through reaction betwaen cemntand aggregate.Proceedings of the Amarican Society of Civil wincers, 1940, 66-,(121, 1781-1811
MCCONNELL, D., MIELENZ, R.C., HOLUND, W.Y. and GREENE, K.T.:&rent-aggregate reaction in concrete.Journal of the American Concrete Institute, 1947, 19, (21, 93-128
TRFMp&, B. and DREW, E.D.: California's concrete aggregateresouxes.Rock Products, 1953, 56, (11, 147-149, 200-201--
AMERIcANSCCIETYFoRTESTIKANDKU%UALS: Specification forPortland cement.ASIM c150-74
LLCBER, F.W. and SPRUNG, S.: Causes andmechanism of alkali-aggregate reaction.Beton, 1973, 2, (71, 303-306 and (81, 349-353
EWEXRFF, P., IDDRN, G.M., KJAER, A., PLUM, N.M. and POUISEN, E.:Chemical reactions involving aggregate.Proceedings of the Fourth titernational Symposium on the Chemistry ofCement, Washington, 1960. Vol. II, Paper VI-l, m-749-806
9. ASSCC~ BRASIL~?ADE~RMAS TECNICAS: Cimntomrtland:EspecificaCao.AE%?T/CB-18 (19th January 1973)
10. INSTITU'IO DE INVESTIGACION TECNCIKXA INDUSIXAL Y DE NORMASTECNICAS: C&auto Portland Tipo I, Normal.IIT= 334.009 &@ember 1971)
11. COMISION VENEZOLANA NOEUQS INDUSIRIALES: Especificaciones paracwanto Portland,CCCA: Ce 100 (1972)
12. DIRECCIONGENERAL DENORM?lS: Norm Oficial para Cmanto Portland.lx% Cl-1955
13. DAVIS, C.E.S.: Studies in -t-aggregate reaction. XVIII. Theeffect of soda content and of cooling rate of Portland cement clinkeron its reaction with opal in mxtar.AustraJian Journal of Applied Science, 1951, 2, (11, 123-131
14. DAVIS, C.E.S.: Studies in cemant-aggregate reaction.: XXVI.Caxpaxison of the effect of soda and potash on expansion.Australian Journal of Applied Science, 1958, 2, (11, 52-62
15. DIAMMD, S.: A review of alkali-silica reaction and expansionmechanisms. 1. Alkalies in cemsnts and in concrete pore solutions.Cenwt and Concrete Research, 1975, 5, (41, 329-346
16. ~PQLLI'IT, H.W.W. and mCX@, A.W.: Tk distribution of alkalis inPortland cement clinker.Proceedings of the Fifth International Symposium on the Chemistry s?Carwt, Tolqo, 1968. Part I, Vol. I, Paper I-126, pp. 322-333
17. MAIIOUXHEX, F.: An explanation oflq formation in cemantZment-Kalk-Gips, 1972, 2, (81, 395-396
18. MCCOY, W.J. and ESHEXUR, O.L.: Significance of total andwater-soluble alkali contents of Portland-t.Journal of Materials, 1969, 2, (31, 684-694
19. CHDWZH, V.F., AZELITSKAYA, R.D., m. I.F. andMMXIKIN, Yu.1.: Effect of alkalis on mineralisation and hydrationprocesses of calcium silicates.Tsentant, 1963, (51, 7-9
20. 'JDROFW, N.A. and IxIBRovoL'SKIY, K.A.: The effect of salts of themat&s sodium and potassium on the formation of clinker minerals.Tserrwt, 1965, (11, 6-7
2l. m, G,: Contribution to the alkali problem in suspensionpreheater kilns.Zemnt-Kalk-Gips, 1962, l5-, (51, 197-204
22, WEBER, P.: Heat transfer in rotary kilns with due regard to cyclicprocesses and phase formation.Wiesbaden, Rauverlag, 1963
23. BPJITBEL, H.: Service conditions and wear of mgnesite liningmaterials inrotaqcemntkilns.Zemant-Kalk-Gips, 1976, 2, (71, 308-312
24. ROCITSCHKA, G. and MAJDIC, A.: Refractories for the cenent industrya review.Zmant-Kalk-Gips, 1974, 27, (101, 469-485
25. -G, W., OPITZ, D. and SIMMMANN, J.: The hsring of burntdoltits bricks in cemntkilns.World Cement Technology; 1977, 8, (21, 39-46
26. TRXER, F.: Deterioration of cement rotary kiln linings by alkalisulphides and sulphates.Am&can Ceramic Society Bulletin, 1968, 47, (71, 630-636 (including adiscussion note by W.S. Treffner)
27. LCXZHER, F.W., SPRW, S. and OPITZ, D.: Reactions associated withkiln gases. Cyclic processes of volatile substances, coatings,removal of rings.VDZ Congress oh Process Technology of Cement Manufacture, Diisseldorf,1971
28. RITZMANN, H.: Recirculation problem in rota& kiln systems.Zement-Kalk-Gips, 1971, 24, (81, 338-343
29. -, H.R.: Wet or dry process kiln for your new installation.Reek Products, 1974, 77, (51, 92-98, 100
30. DANckJsKI, W. and STROBEL, U.: Investigations of alkali load tolerancein dry-process kiln plants.Zexnt-Kalk-Gips, 1976, & (101, 458-462
31. NORTH, F.J.: Limastones, their origins, distribution and uses.London, Murby, 1930, p.439(quoting CLARKE, F.W.: Data of geochemistry. US Geological SurveyBulletin, 1924, No.770, p.564)
32. RUNDLE, L.M.: A canbustion m&hod for the determination of totalsulphur in limestones.The Analyst, 1974, 99, (March), 163-165
33. General Portland's use of aragonite at Tampa plant.Pit and Quarry, 1973, 65, (91, 60-64
34. PAUGR, K. and ENLESS, 0.: A study of alkali volatilization inPortlandcemntrawmixes.Portland Cm-eat Association report M-127, 1952
35. DUDA, W.H.: Cmtdatabmk: international process engineering inthe cenmtindustry.Wiesbaden, Bauverlag, 1976.
36. WEAVER, C.E. and POW, L.D.: The chemistry of clay minerals.Amterdam, Elsevier, 1973
37. CEtOSSLEy, H.E.: A special study of ash and clinker in industry.Paper 4: external boiler deposits.Journal of the Institute of Fuel, 1952, 25, (Sept.), 221-225
38. FURLONG, L.E., EFERCN, E., VERNON, L.W., WILSON, E.L.: The Exxondonor solvent process.Chemical Engineering Progress, 1976, 72, (81, 69-75
39. KEYSSNER, E.: The occurrence of iodine in cemnt flue dust.Chemische-Zeitung, 1925, 2, 821 ..
40. PERRY, R.H. and CHILITON, C.H.: Chemical engineer's handbook.New York, McGraw-Hill, 5th edition, 1973.
41. CINES,-M-R., HAS=, D.M. and HOUSER, C.G.: ti1ecula.r sieves forremoving H2.S frannatural gas.Chemical Engineering Progress, 1976, 72, (81, 89-93
42. f4t.zCORD, A.T., WAGNER, L.E. and REESE, T.J.: Process for rtaking lowalkalicemautclinker.Us Patent 4,001,031 (4th January 19771, assigned to Chem+'rolPollution -ices, Inc.
43. PORTER, E.S. and ToI;ER, H.J.: Remving alkalies fran raw materials.Portland Carwt Association report MP-99, 1961
44. KAYE, G.W.C. and LABY, T.H.: Tables of physical and chemicalconstants.Imdon, Ion-, 14th edition, 1973
45. SEE, J-B.: Fluorspar and fluorine cmpounds in high-terqeraturesmelting and refining of matals,Minerals Science and Ezqineering, 1976, 2, (41, 217-241
46. IWAKYID, N., SUITQ, M., HAM%%TSU, S. and SA'IOH, I.: Malting pointsof inorganic fluorides.Transactions of the JWRI, 1973, 2, (21, 204-207
47. J?CKSON, D.D. and M3RGAN, J.J.: Measurmsntof Mporpressures ofcertainpotassiumcunpounds.Journal of Industrial andEngineering Chexnistry,192l,~, (21,llO-ll8
48. HALSTEAD, W.D.: Saturatedvapour pressure of @assiumsulphate.Transactions of the Faraday Scciety, 1970, 66, (81, 1966-1973
49. CUBICCICYITI, D. and KECJESHEA, F.J.: Thermdynamics of vaporization ofsodium sulfate.High Tmparature Science, 1972, 4, 32:40
50. BA-, R-J., IEFEVER, R.A. and WILCOX, W.R.: Evaporation of sodiumchloridemalts.Journal of Crystal Growth, 1971, 2, 317-323
51. TmoR, L.: The vaporization tiermdynamics of fused lithium andpotassium fluorides.Journal of Chemical vcs, 1976, 5, (81, 777-783
52. FICAILIRA, P.J., UY, O.M., MUENW, D.W. and MARGRAVE, J.L.: Massspectramatric studies at high teqeratures: XXIX, Thend.decaqmsition and sublimation of alkali rmatal sulfates.Journal of the Amarican Ceramic Society, 1968, 51, (101, 574-577
53. HART, A-B., QGLNER, G.C., HAISTERD, W-D., IFXTON, J.W. and TIDY, D.:Scme factors in seed recovery. 'International SyqmsiumonMagnetchydrodynamic Electrical PowerGeneration, Paris, 1964, Session 7, Paper 89.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
HART, A.B. and LAxroN, J.W.: Samaspectsofthem.h.d. seed.Philosophical Transactions of the Royal Scciety of261, 541-557.
DRAPER, J.: Iaboratorystudyof alkalimmmlinprOCSs - a progress report.Portland Cement Association report MRS-68, 1954.
chemistryof
London, A, 1967,.
the cement burning
DRA?TR, J.: Alkaliremval in the cement burning process -a study ofoperating data.Portland Cemant Association report MRs-69, 1954.
EWTIN, Z.B., FRIDMAN, I.A. and mKBICV, V.K.: Study of thevolatilisation of K20 using mthmatical vimantal designTsemnt, 1966, (41, 7-9.
GOFS,C andKEn, F.: The behaviour of alkalis in cmentburningTonindustrie-Zeitmg, 1960, 84, (81, 125-133.
ANDERSON, E and NESTELL, R.J.: The volatilisation of potash francenentmterials.Journal of Industrial and Engineering Chemistry, 1917, 2, (31,253-261. _
T0ROK)V, NA. and cOBROVOL'SKIY, K.A.: Volatilisation of sodium andpotassiumoxides during clinker burning andtheir distribution in theminerals.Tsement, 1965, (31, 6-7.
GRAZHDANSKIY, S.A., KINSTLW, K.M. and ABUIA, S.Ya.: m ofreducing the alkalicontentof clinker.Tsemnt, 1965, (31, 18-19.
J?CKSCN, D.D. and MlRGAN, J.J.: An application of the vapor pressuresof potassium cmpounds to the study of the recovery of potash byvolatilisation.Journal of Industrial and E&nearing Chemistry, 1921, 2; (41,292-295.
KOIX, H.: Remving alkalis by heating with admixtures.Rock Products, 1942, 5, (21, 66-68.(a reprint of FCA report M-74, 1941.1
LMWUR, H. M&.: ~ethodof reducing alkali content in PortlandcerrPntclinker.Portland Cement Association report M-74, 1941.
TXWXJR, H. McC., MCMASTER, E.T. andJACQUES, W.: Manufacturing lowalkali Portlandcemntclinker.Rook Products, 1943, 46, (71, 59, 67, 68, 74.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
CARLSEN, H.: The behaviour of alkalis in cement raw materials duringthe burning process.Rock Products Annual Cement Industry Operations Sem,inar;1965.(reprinted in Rock Products, 1966, 2, (51, 87, 88,' 157)
LOVELAND, R.A.: Reduction of alkalies in cement kilns (study byquestionnaire)Portland Cement Association report MRS-61, 1948.
HOLDEN, E.R.: Reduction of alkalies in Portland cement - use ofcalcium chlorideIndustrial and Engineering Chemistry, 1950, 42, (21, 337-341.
GILLILAND, J.L.: Removal of alkalies by use of hydrochloric acid.Symposium on alkali removal and problems, Milwaukee, Wis., 1959.Portland Cement Association report M-158, 1960.
WOODS, II.: Reduction of alkalies in cement manufacture.Portland Cement Association report M-149, 1956.
NDDEL'MAN, V.I. and UVAROVA, 1.T.: Method of reducing alkali contentsof clinkers from cement works in Central Asia.Tsement, 1968, (41, 12-13.
SPRUNG, S. and SEEBACH, H.M. von: Fluorine balance and fluorineemission of cement kilns.Zement-Kalk-Gips, 1968, z, (11, l-8.
BANIT, F.G. and VASILIK, A.V.: Influence of gypsum-bearing additiveson exit gas dust removal.Tsement, 1972, (61, 17-18.
HATANO,H.: The behaviour of sulphur in the suspension preheater kilnsystem.Zement-Kalk-Gips, 1972, 25, (11, 18-19
COLUSSI, I and LONGU, V.: Thermal decomposition of calcium sulphate.11 Cemento, 1974, 71, (21, 75-98.
REMIREZ, R.: Gypsum finds new role in easing sulfur shortageChemical Engineering, 1968, 75, (241, 112-114.
Production of cement and sulphuric acid from gypsum.Cement and Lime Manufacture, 1968, 41, (41, 53-60.
MERZ, A.R. and ROSS, W.H.: The nature of recombined potash in cementmill dust.Journal of Industrial and Engineering Chemistry, 1919, 2, (11, 39-45.
BROWNMILLER, L.T. and EOGUE, R.H.: The sys tern CaO-NaZO-AlZO3.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 25, 1932.
80.
81.
82. TAYLOR, W.C.: The system 2.CaO.SiO2,K 20.CaO.Si02 and other phase
83.
84.
85.
86.
87.
88.
89.
90.
91.
BROWNMILLER, L.T.: A study of the system lime-potash-alumina.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 30, March 1933.
TAYLOR, W.C.: Phase equilibria studies on mixtures of the compounds4CaO.Al2O3~Fe203-2CaO.Fe203-K2O.A12O3.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 37, September 1938.
.equilibrium studies involving potash.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 40, September 1941.
TAYLOR, W.C.: Further phase-equilibrium studies involving the potashcompounds of Portland cement.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 43, December 1942.
EUBANK, W.R. and BOGDE, R.H.: Preliminary study on portions of thesystems Na20;CaO-A1203-Fe203 and Na20-CaO-Fe203-Si02.Portland Cement Association Fellowship at the National Bureau ofStandards, Paper No. 50, March 1948.
NEWKIRK, T.F.: Effect of SO3 on the alkali compounds of Portlandcement clinker.
Journal of Research of the National Bureau of Standards, 1951, 47,(51, 349-356.
NEWKIRK, T.F.: The alkali phases in Portland cement clinker.Proceedings of the 3rd International Symposium on the Chemistry ofCement, London, 1952, pp.151-171.
ELLINGSON, O.A., GILL-AM, J.L. and KOPANDA, J.E.: Determination of"water-soluble alkali" in cements.ASTM Bulletin, 1956, (Feb), 63-66.
SEGNIT, E.R.: Further data on the system Na20-CaO-Si02.American Journal of Science, 1953, 251, 586-601.
BA3ATSCHEV, G.N. and RADEVA, K.K.: Alkalis in Portland cementclinker.Silikattechnik, 1961, 12, (11, 33-35.
BUDNIKOV, P.P., AZELITSKAYA, R.D. and LOKOT', A.A.: Effect ofadditions of gypsum on mineral formation in alkali-containing cementclinker.Zhurnal Prikladnoi Khimii, 1968, (5), 953-957.
AZELITSKAYA, R.D., PONOMAREV, I.F., BLONSKAYA, V.M., KARBYSHEV, M.G.,LOKOT', A.A., and STEPANOV, V.M.: .The effect of gypsum on the phasecomposition of alkali-containing clinker.Tsement, 1969, (2).
92,
93.
94.
95.
96.
97.
98.
99.
LIx;ININA, I.G. and SHAPCSHNIKUVA, M.A.: Characteristics of clinkermineral formation in thepresenceof alkalisulphates.Tsemant, 1970, (81, 18-20.
EUIT, Yu.M., KADS~SKII, V-E., TURETSKII, A.M. and iANN, N.S.:Effect of gypsum on the properties of an alkali-containing cmarit.Tsemant, 1971, (41, 14-16.
AHHASSI, G.: A contribution to the study of the influence of alkalimetals an the canposition and hydration of clinker phases.Revue des Materiaux de Construction, 1974, (6911, 315-322.
RITZMANN, H.: Hmtokeepalkalies frcxnstealingprebeaterefficiency.Rock Products, 1974, 77, (21, 6669.(originally presented as a paper entitled "Raw maal preheater andalkali problems" attheRcxkProducts 8th International CemantIndustry Sminar, 1972).
PCYITIZ, N.S. and CHEESMAN, R-D.: Effect of coal ash on the liberationandnature of cmtantmi1lpotash.Journal of Industrial and Engineering Chmistry 1918, 10, (21,109-Ill.(See also correspondence from E. Anderson and R.J. Nestell and franE.O. Rhodes and J.J. Porter in (121, 1030-1033).
-, I. and PURI, A.: Cycle of volatile substances in rotarykilns for Portlahdcemntclinker.Z-t-Kalk-Gips, 1975, 25, (91, 377-379.
IEHMANN, W.S. and PIASSMANN, E.: Determination of the alkalicirculation with the aid of the radio-isotope K42 in a long watprocess rotary kiln.Zmant-Kalksips, 1957, 10, (31, 89-93.
WEBER, P.: Alkali problms and alkali elimination in heat ecoimnisiqdry process kilns.Zearant-Kalk-Gips, 1964, 17, (81, 335-344.
100. VlRlloRENKcrv, V.I. and MLKONSKY, B.V.: Alkali circulation in cyclonepreheaterkilns.Tsemxit, 1965, (61, 12-14.
101. RITZMANN, H.: The effect of dust cycles on the heat consuqtion ofrotary kiln plants with raw maal preheaters.Zemant-Kalk-Gips, 1971, 24, (121, 576-580.
102. SPRLm, s.: The chemical andmineralogical cmposition of cemnt kilndust.Tanindustrie-Zeitung, 1966, 90, (lo), 441-449,
103. LITYNSKI, T. and GODEK, J.: K2C and CaO detennination in foreign andPolish cemant dusts.Zmant-Kalk-Gips, 1965, g, (101, 534-535.
104. HEIIbIANN, T.: Treatmantof dust frcmcemntkilns.British patent 1,145,827, published 19th March 1969, assigned to-F.L. Smidth & Co. A/S.
105. KESTER, BE.: Alkali reduction by kiln dust leaching.Symposium on alkali remval and problems, Milwaukee, Wis., 1959.Portland Cement Association report M-158, 1960.
106.
107.
108.
109.
110.
111.
ll.2.
113.
114.
115.
STEVENS, H.A.: Wetrecoveryof kiln dustandsubsquentalkalireduction.Symposium on alkali removal. and problems, Milwaukee, Wis., 1959.Portland &meat Association report M-158, 1960.
BADE, E.: Process for reducing the alkali cycle in clinker burning.Zanent-Kalk-Gips, 1962, 15, (91, 403-408.
YURGANUV, N.N., SAFONOV, N.A. and BRODKINA, E-R,: Method for reducingalkali circulation when returning dust to rotary kilns.Tseiwnt, 1966, (11, 10-n.
WATSCN, D and ERW, A.W.: Treatment of waste products frcm Portlandcement manufacture.US patent 4,001,030 (4th January 19771, assigned to AssociatedPortlandCerrwt Manufacturers Limited.
EGNN, Wand-HARD, U.: Cementwxks experience andconsiderationsrelating to the design of bypass system.Zerrwt-Kalk-Gips, 1972, 25, (61, 281-282.
HAEMms, P.: Alkali behaviour in a suspension preheater using a gasby-pass - practical experience at the Rillito installation.IEEE Cement Industry Technical Conference, Tucson, Ariz. 1976.
SCHLUJ!ER, H.: Process for reducing the alkaliandchlorine cycles insuspension preheater kilns.Zerwt-Kalk-Gips, 1972, 25, (11, 20-22.
CHRISTIANSEN, S. and MADSEN, G-M.: The development and application ofprecalciners for cement kilns.Reek Products, 1975, 78, (51, 85-88, 126.
SMIMH, F.L. & CO. A/S: ~ethodof burning cement.British patent 1,023,910, published 30th March, 1966.
lIED&DT, H.: Measures for reducing the alkali cycle in the [email protected] Congress on Process Technology of Cmznt Manufacture, Dusseldorf,1971, 164-167.
116. -T, E.A. and HEIAN, G.A.: Alkali remval via grate - kilnSyStem,Rmk Products, 1973, 7fi, (51, 60-64, 179.
117. CLAUSEN, C.F.: U+mlkali cemmt fran high-efficiency kilns?Rock Products, 1960, 63, (11, 148, 149, 152, 154, 164.
118. POLYSIUS GMEi: Process andapparatus for producing -toflowalkalicontent.British patent 874,818, published 10th August 1961.
119. VEIGEZ, J.F.: Problems of alkali reduction in the Htildt system.Sympsosium on alkali remval and problem, Milwaukee, Wis., 1959.Portland Cetrent Asscciation report M-158, 1960,
RRC/TGB/JMLC/b3111.03.87.
TABLE 1
Melting andimiling pints of selected calcium, potassiumand sodiumc-unds.
Camp&d Mslting point("Cl
Eoiling Point("Cl
CaCO3 C!ecoqases 899 (calcite)
--cam2 772 - 782 > 1600 - 2000
c*2
Ca(OHI2
Cd0
1386 - 1423 (45)
deccmpses 580
2570 - 2600
2500
2850 - 3000
- 4 1450
KP3 891 ckcqoses
KC1 776 - 790 1407 - 1500
ET 846 - 858 1505
IUJH 360 - 380 1320 - 1322
KiQ
K2Si03
K2Si$5
K2s04
*a2C03
N&l
NaF
NaOH
*aZo
Na2=2o5
Na2SiO3
Na4SiO4
*a2=4
ckarposes 350
976
1015 * 10
1069
851
801
988 - 997 (46)
318
874
1088
1018
890
1689
dL3XiVpSeS
1413
1695
1390
sublines 1275
RRC/+IGB/JMLC/b3111.03.87.
fi;.’
--.-
,...I: -‘-
-..--+
:-!.:
-
L .
__
:
_ .
:t:‘.
. .
.i
.:..
.:. .
!---C
L...
.: 8
.
I .:1
.
‘,
: ‘..:‘I:
; I:
:
2-..--
-:-I-
I
:.:
:.;..- ;I-
l----:L.L-.--i
.:. -!!,,f;;<
.-
I[‘.
.-:
,i
, I
! ..!..Y
!
\- :\.
\
)I._!
:
,L
-i -
I‘i-
t-r:
7: :I20 v
ol2tilisation (
Log
sce
l.--
-
-
_ _
.I
,.
_.::
y::
I.
,,.
_.
_.
:.
1-1
J--+
y-p~
.-y--‘“p
q
_ ,-.
I :-
:..
.,:
.:
‘:
. .._
_ ‘__
_.
. . .
. . .
. . .
. . -
.
..
,:
. 1:
:..[
:I.:
~
-.~
:--:
:j..-
~:~
:1.
. 1
:‘-:
1
r.I
: -.
.I:
: ::
1:
- .- -/__ -.. :.---/ : F&pure 3 ---_: i i ,-.--
..- i--‘--_-e i--q. -_. ,1-. _- I -!-! .-- LLJ--L .q ..____ T:. ..i
.c ;
------i --.-.._. . .._
t I ...TW\‘\.-Lp:;I ; j _ j ic;. --y-y--.,
i-i Ii-. . .
p-1 &- _4
3 c ( -i- ---t’-~---I7 i .bh .\
f I I 1 .I .-1.... ! : i1 t
.-..--- i .-.- --.,-. ‘-.I ______I I
j __.. i ______ I-. _.__ / i: r---- ;- - - --- --.---L ____ l..- i---.\p.I j I ! j. ./ mien ]: /_i\i:-+-i-i-; - _- ..i.- -.*-:.&-- - c---. -.I.. . . i. ..__ 1..--i _._...___ i .____. i’___._ i... I T-77
_I i
-- :-- ---i
i
:-/. ..j
Figure 4
[ I I..--..!--L--L.. _- :-...--,.- ____ 1.. ._. f i .:. i. j I : ._ : :
3 : i .: ! . : ! /; .
._. . ) --.2-L;.. -.-l’;-’ ..- i. .: ;ai i ‘I- 1. ! : . T’ -I : . - : .y,I : : i
i;----;- -’ i: .- ; : -::...;. : : .. _.
L _ _ _ _. . . i _ -u L. -2 .-L-L-.:.:.: I .: /.‘-
8. ,.. i-’ .-._-.- .---L .._.__ .-.-.!.-I
.-. 4
3
F&me5
t7-------- ..--_ _ - .__-- T.--.- . .._~ _.,_ -. __._- j___- -. - .-5;
,- : _-_1 : ._’ _ .;
r9/2 ‘f- -7
.____ _ ..____.. - -- ._-- -- --_. .1 /3; ..i .--.. ;. :--... :__ _ _*- I
.--._--_--- -__-/
. _ __ - ..-- I;-- : ;--,-. c-,..-“--.‘ -_-_i --.. -- _ _ - _-.. _._- _. .__._. .- _.. ____! i i j . : i ;.. . :... i . ..-) .._. :‘--[ -.-- *- - -.-/ j --.
I _ __-_ &.- ‘__ __-----_ --.:-.+--;--;. I-- 7 . i yy-y- 1
---_-___----I
. 8 . ’t
A------.:-.-- .-_---.. --,-I--.- :_-__-___; __.. ;T j . j _ ;
i : T: 1-m ._-1 I -.---+---I
! .. /&,-A--;-:: _____ -LL :. ---i..--. 1.
_ i ,; : .-!
i _-. I; ~ :
1. ..- -...--- -:.-.-...-..I.: :. ;.:
! - ----: - ._,.-- --.:..--- _-.-- w-1-.
50;
. ! .’
/L . _ _, _ \ -..
-_ .-- --..- ------ - ---- -
._.-: . . :_ . . .-..1..- . --._... :: --! ‘I
: . !. :
~+:~.:z-i;,-~.‘7;~~; : . : :---- -z-._-_ . . -
;f-T. i -..--.:
: :, _-: F -:--:-- :
_ _ _..- .___ :. ._- ;.-:I .:. :.
L -_.-_. ,t :- ._i_ :::.~ I
.--;e ---.- / -. --. . . ,r ‘l-r.. L-. i-.“:--‘-f ., .: -, 8 -. ;
4-Q
-- -.--.- _ -
: :
.-i---.- -- -.: i--.: . ...’ ___._ i
‘..-: ~1 :
:.: : ;
-- --
! -L.---L.--- _. . -i__ i : :
i: . --._---_-___-- - -_- --.
rL.-.+ ._.- .;. .-. _ ‘ :--;.. :: I. : .: .
- ..---~ __-. -..--..- -/.. ,
Figure 6
~-y----;.: : :.
_:. \ _. .:-I:-. _ !
1::. j .:..i. .I... ..-;~+L+L.+ -
; :, :, ..!:: L..::/. I. . . . .: I :: : I I I -- -. ) . .:.... .:: ,:: _.
-‘---~~Y---y-
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 6
A Study in the Volatile Cycles on HOPE#2 Kiln
A series of seven tests have been conducted at Hope Works during which the
No. 2 kiln was operated at selected, controlled levels of kiln back end
NOx (equivalent to burning zone temperature) and oxygen in order to study
the effects on volatile cycles of these different regimes. Each detailed
study period lasted at least twelve hours and samples were collected from
various points around the kiln and preheater system for analysis.
CONCLUSIONS
The test results indicate that the chemical proportions of the minor
constituent volatile components at Hope lead to the following cycle
levels in stage IV meal.
The typical fluoride cycle level is 1.2 to 1.4 times the input to
the system and does not change substantially as the kiln temperature
or atmosphere is modified, over the range studied.
The chloride cycle is 20 to 30 times the total chloride input and
increases slightly with increasing temperature, although this may be
due to improved kiln stability at higher temperatures. The chloride
cycle is not modified by vide changes to kiln atmosphere.
3. The chloride cycle is a low temperature cycle and cannot be
significantly modified by variation of kiln conditions.
4 . Chloride in the cycle combines with potassium where available.
However, at low temperatures - equivalent to NOx levels of below
1,000 ppm - some sodium is also involved.
5 . The total potassium cycle is approximately 3 times the input level,
however about two thirds of this is present in Stage IV in conjunction
with chloride and so cannot be controlled except by incorporation of a
bleed sys tern.
6. About one third of the potassium in Stage IV is either feed based on
its first passage through the preheater or derived from a potassium
sulphate based cycle. This cycle ratio varies from 1.05 (minimal
recycle) at 900 ppm kiln NOx level to 1 .25 at 1,400 ppm NOx (25%
r e c y c l e 1. This portion can be controlled by operation at low
temperatures.
7 . The sodium cycle level varies between 1 .2 and 2.0 times that in the
rarnneal over the temperature range examined.
8 . At low temperatures some sodium becomes involved in the low
temperature chloride cycle and this boosts the sodium cycle by
about 10%.
9 . The majority of the sodium in the system is involved in a sodium
sulphate based cycle. This is strongly temperature dependent, and
the rate of increase also appears to be increasing with temperature.
Over the temperature range investigated the cycle rose from 1.35 times
t h e l e v e l i n t h e feed at low temperatures to 2.0 times at high X0x
l e v e l s .
10. The total sulphur cycle is temperature dependent and rises from 1 .5
to 2.0 times that of the input over the temperature range investigated.
11. The alkali sulphate cycle has already been summarised in Points 6 and
9 and makes up about 35% of the total sulphate in Stage IV material.
These cyclic levels can be seen to be lower than the total sulphur
c y c l e l e v e l s .
12. The calcium sulphate recycle is strongly temperature dependent and
rises from about 2.5 times the level in the feed at lov NOx levels to
4 times at high (1,450 ppn) NOx levels.
13. The calcium sulphate cycle is also increased by a move into a
reducing kiln atmosphere. At about 1,200 ppm NOx the cycle
increased from 3.1 under oxidising conditions to 5.5 times the feed
level under reducing conditions.
14. For potassium and sodium there are indications of a slov but steady
increase in losses of these components from the preheater system
as temperatures increase. This may become part of an external
cycle or may be lost to atmosphere. This could be established by
a longer term study of the levels of these components in the
precipitator and stack dusts.
15. Sulphur is in overall balance within the system belov NOX levels
of 1,200 to 1,300 ppm, but above this level the loss increases
sharply with rising temperature. Again this may become part of
an external cycle or may be lost from the systen, hovever in this
exercise no precipitator or stock dust samples were collected so this
cannot be confirmed.
16. When the kiln a:mosphere moves into reducing conditions the losses
of alkalies and sulphur from the kiln system increases sharply.
In viev of these conclusions it is recommended that, at Hope:
1. Kiln back-end oxygen level is maintained at 2.0 to 2.52
(as measured).
2 . Kiln back-end NOx levels are maintained below 1200 ppm, although
the most appropriate NOX level will depend on detailed raw mix
chemistry.
3. Communication between kiln burner and personnel cleaning the
preheater be improved.
4 . During cleaning operations short term reductions in raw meal feed
vhich avoid the inception of reducing conditions will be
b e n e f i c i a l i n t h e l o n g e r t e r m .
N O T E : C y c l e = quan:ity i n S:age I V - o n a l o s s f r e e b a s i s
quantity in feed on a loss free basis
F u e l i n p u t l e v e l s f o r a l k a l i e s , fluorides and sulphates have not been
taken into account as the levels are relatively lou and constant, as
indicated from the small number of fuel samples that were analysed.
The chloride input from coal has been taken into account.
1. INTRODIJCTIOfi
Since the development of the suspension preheater based dry process for
cement manufacture the study of the inherent cycling effects of the
potentially volatile components, which are present as minor constituents
of the raw materials and fuels, has become increasingly important. In
the less thermally efficient plants a natural loss of a portion of these
volatile components occurred in the waste gases so automatically
controlling the recirculation levels within the burning system and the
l e v e l i n t h e c l i n k e r p r o d u c t . P r e v i o u s l y t h i s l o s s o f v o l a t i l e
components has also been higher than would be found today due to the
capabilities of the available pollution control equipment, as the
volatilised components condense on fine dust particles in the cooler
z o n e s o f t h e k i l n . I n the suspension preheater, with its greatly
increased surface contact between gas and particle and repeated
separation of gas and particle, the recovery and retention of
volatilised components will be almost complete. This leads to
increased proportions of these components in clinker and to the
development of operational problems in the pyro-processing stage due to
the quantities of the potentially sticky components that build-up
through cyclic processes. These effects limited the immediate impact
of the suspension preheater technology in the industry as a whole for a
number of years. Nevertheless increasing fuel prices and the
requirement for even larger process units provided the incentive for
identifying the causes of and solving the problems associated with
volatile component cycles 1~3. In general this work has been
targetted at controlling alkali levels in clinker and/or maintaining
the recirculation levels wi:hin such boundaries that allow reasonable
kiln operation, whilst the solutions have been limited to indirect
methods of control; modification of the raw mix, change of fuel,
installation of a bleed system, manual or automatic cleaning of areas
where excessive bui Id-up occurs .
During the developaent phase of the high level control project at Hope
Works it became evident that considerable changes in the volatile cycle
were produced as the combustion chamber conditions were modified. The
more consistent control and greater understanding of process conditions
vithin the kiln that vas developed through the reliable measurement and
interpretation of kiln back end NOx level in association vith the more
conventional instrumentation offers the potential for deliberate modi-
f i c a t i o n a n d c o n t r o l o f t h e v o l a t i l e c y c l e s b y v a r i a t i o n o f p r o c e s s
conditions on a plant scale. This would then permit the minimisation
of troublesome volatile cycles and hence lead to improved kiln stability
and operating times.
Consequently, it was decided to investigate the exient of variations in
the volatile cycles vhich could develop by operating a kiln under a
number of temperature and gas compositional (oxidising/reducing) regimes.
Over the course of the last tvo years, as operational restraints and
manpower availability have permitted, a series of seven studies have
taken place on No. 2 kiln system at Hope Works. In these studies three
different kiln back end NOx levels (800 to 1,400 ppm) and three kiln
atmosphere conditions (reducing to high excess oxygen) were targetted
as shovn in Table 1 . Previous vork 4j5y6 has shovn the general
relationship betveen kiln h’Ox level and burning zone temperature.
Although it is not possible to equate a particular NOx level vith an
actual definitive material or flame temperature at the fron: end of the
k i l n , t h e t y p i c a l r e l a t i o n s h i p f o r N o . 2 k i l n a t H o p e i s shovn i n F i g . 1 .
For control purposes the advantages of NOx measurement are that above a
base level NOx generation is proportional to the temperature of the
burning zone - v i t h i n s p e c i f i c l i m i t a t i o n s , - t h e r e i s a v e r y f a s t
reaciion t i m e , t h e s i g n a l s u f f e r s r e l a t i v e l y l i t t l e p r o c e s s n o i s e , a n d
the true reading is unaffected by front end dust cycles.
2 . VOLATILZ CYCLES
2.1 General Considerations 7,8,9,10
The minor components that are generally considered to be involved
in major volatile cycles are the chloride, alkali, and sulphur
s p e c i e s , with some attention also being paid to fluorides. Prime
control of the volatile component cycles is performed in the
design stage of a Works project through the selection of rav’
materials and fuels in order to optimise the relative and absolute
levels of the potentially volatile components and, if necessary,
the inclusion of a bleed system. Once these factors have been
defined the volatiles will develop internal and external cycles
during the pyro-processing stages; an internal cycle being
totally within the kiln and preheater system, vhilst an external
cycle will leave the system but be returned after a time lag (for
instance with the precipitator dust). Where processing condition2
are kept steady, the cycles will continue to develop uniil
equilibria are reached, at which time the total amounts of
volatile entering the system will be balanced by the quantities
leaving the system.
The degree of volatilisation and the rates at which the
equilibrium are established will depend on:
(i)(ii)
( i i i )
(iv)
(VI
(vi)( v i i )
( v i i i )
( i x )
(xl
The species, their chemical forms, and concentrations.
The volume of gases.
The intimacy of contact between gas and solid.
The vapour pressures of the salts.
P o s s i b i l i t y o f d i s s o c i a t i o n o r f u r t h e r r e a c t i o n .
Rate of diffusion to and from solid/gas interfaces.
Degree of saturation of gas.
K i l n a:mosphere.
Kiln temperatures.
Time/temperature profile of material within the kiln.
lost of these factors are to some degree inter-related, and so in
norma 1 operation the only methods available to control the degree
of volatilisation will be the kiln internal atmosphere and
temperature.
The major cycles will be internal cycles between the burning zone
and preheater where an individual cycle time of twenty to thirty
minutes would be expected. Smaller quantities of volatile
components may be involved in the longer term external cycle which
develops via the precipitator dusts and volatile collection in the
raw mill . These would be expected to have much longer cycle
times of up to twenty four hou:s.
2 . 2 F l u o r i d e s l1
Fluorides can be found naturally in raw materials or be
deliberately added in small quantities to the raw mix. In low
proportions its mineralising action has a beneficial effect on the
burning process. Generally it has a low volatility and causes
few operational problems, although a level of above 0.25Z in
clinker may lead to setting problems particularly in winter.
However, cases have been cited vhere a hard dense build-up has
developed in preheaters, where the build-up contains high (over II)
p r o p o r t i o n s o f f l u o r i d e .
2 . 3 C h l o r i d e s l2
Chlorides are derived from the raw ma:erials and the kiln fuel.
Either source will only have very small quantities of inherent
chloride, but the high volatilities of these compounds together
with the high collection efficiency of the cyclone preheater
systems will lead to the development of a greatly enhanced cycle.
The chlorides have a high affinity for the alkalies in general and
potassium in particular. This property - together with the high
volatility - has been used in wet process kilns to control clinker
K20 levels by addition of CaC12 to the rav mix o: fuel, which
leads to loss of KC1 with the exhaust gas from the kiln. In the
suspension preheater, however, the volatilised material is
recaptured within the system unless a bleed is utilised between
the kiln and riser duct. It is generally considered that no more
than 3X of the chloride passing from the preheater to the kiln
vi11 l e a v e the system with the clinker. Although considerably
higher levels have been noted in individual samples of clinker
this is probably due to a ‘push’ of kiln feed, or a semi flush
situation as thermodynamic consideration indicate that no chloride
should pass through the burning zone. On many SP kiln systems
some degree of preheater cleaning is necessary on a regular basis
and this may help to control the chloride cycle by forcing the
kiln conditions into a situation which permits a brief increase in
clinker chloride level (i .e s reduced material temperature,
increased material loading and flux level).
Small amounts of chlorides will also leave the preheater system
with the waste gas stream. Results of detailed balances at Rope
and Plymstock suggest that the preheater loss can be of a similar
o r d e r t o t h a t i n c l i n k e r . Taking the total loss of chloride from
the system as between 2 and 5% of the feed to the burning zone -
it would then be expected that a circulating load of 20 to 50
times the rota1 chloride input vould develop.
2 . 4 A l k a l i e s 13p l4
The major source of alkalies will be the raw mix; notably the
clay component although minor quantities can arise from :he fuels.
The initial free alkalies will behave in one of three ways:
1. Remain in the material being processed and become
incorporated in the clinker constituents that are being
formed . This happens to Na20 to a greater degree than K20.
2 . 3e converted into different compounds - chlorides, sulphates,
carbonates, hydroxides - by reaction with other constituents
of the raw mix.
3 . Diffuse to the surface of the process material and volatilise.
I n i t s ini:ial s t a t e K20 b e g i n s t o v o l a t i l i s e o v e r a w i d e r a n g e o f
temperature, depending on the form of clay in which it was
incorporated, but irrespective of source it would be expected to
have volatilised almost completely at burning zone temperatures
although some may have been at least partially stabilised by
conversion to the less volatile sulphate form within the material
bed. Once volatilised it will react to form chlorides and
sulphates at the rear of the kiln. These will then deposit on
d u s t p a r t i c l e s . I n i t i a l l y , Na20 i s l e s s v o l a t i l e t h a n K20 d u e t o
its higher bond energy and so a greater proportion of the kiln
feed Na20 would be expected to pass through the burning zone in
c l i n k e r w i t h o u t p a r t i c i p a t i n g i n t h e v o l a t i l e c y c l e s . Volati l ised
Na20 will react with SO2 and SO3 to form sulphates towards the
r e a r o f t h e k i l n , and with chloride vhere this species is present
i n e x c e s s o f K20. Where alkali is present in excess of chloride
and sulphate, alkali carbonates will be formed. Each of these
alkali compounds will deposit in a liquid state on the surface of
dust particles in the cooler zones of the kiln and lower preheater
stages and will enter the volatile cycles as the dust is separated
o u t i n t h e c y c l o n e s . Direct contact onto kiln or preheater
surfaces may lead to the development of build-up. The compounds
will then re-enter the kiln where the degree of volatilisation
will depend on the species and the kiln conditions. V o l a t i l i t y
decreases from chloride to carbonate to sulphate, and hence
sulphates are more likely. to pass through the burning zone.
Nevertheless the likely range o f burning zone temperatures cover
the thermal area in which alkali volatilities are likely to
increase significantly with rising temperature.
2 . 5 S u l p h u r 15s16~17
Sulphur can enter the system in a number of forms from either fuels
or raw materials. A limited amount may evaporate in the upper
preheater stages and escape from the system in the exhaust gases.
In general SO2 and SO3 can form in the high temperature areas and
b e t r a n s f e r r e d t o t h e g a s p h a s e . I n t h e c o o l e r a r e a s o f t h e k i l n
back end and preheater system, sulphates will form and re-enter
the material stream. Preferentially alkali sulphates will be
produced with excess sulphate combining with free lime or calcium
carbonate that is available in these areas. k’here r e d u c i n g
conditions exist the equilibrium will favour the existence of SO2
a n d SO3, so restricting the formation of sulphates. In this
situation loss of sulphur oxides by way of the stack may increase,
but where the gas stream passes through the raw mill the majority
of the sulphur oxides would be expected to react with the high
active surface calcium compounds which are produced in the milling
process. This will :hen return to the kiln in the raw mix as part
o f a n e x t e r n a l c y c l e .
The high boiling points of the alkali sulphates would indicate
that relatively low levels of volatilisation would be expected.
Bowever, dissociation may occur, particularly under the reducing
conditions which can exist to some degree within the burning zone.
Calcium sulphate also has a high boiling point, but is even more
susceptible to dissociation, so a higher recirculation of sulphate
from this compound would be expected. As CaSC& cannot recycle as
a compound the lime from this compound remains in clinker as free
lime - making burning more difficult - whilst the SO3 is carried
in the gas stream CO the kiln back end where it reacts to form
a l k a l i o r c a l c i u m sulphate.
3 . PROCEDURZS
The intention was to operate the kiln under controlled back end oxygen
and kiln temperature regimes, w i t h k i l n backend NOx l e v e l b e i n g u s e d a s
an indication of change in temperature. The selected target &OX levels
were 800, 1,200 and 1,400 ppm. For each of these temperature conditions
two back end oxygen levels were targetted; 1.8% (moderate) and 2.5%
(norma 1 oxygen 1 . At Hope Works there is a positive offset of 0.6 to
0.8% for the measured value of kiln back end oxygen as compared to the
real value due to the type of sampling system. In addition to these
s i x t e s t s , a further run was conducted at 1,200 ppn~ NOx with CO evident
at the kiln back end - reducing conditions in the burning zone (Table 1).
Each test run lasted at least twelve hours, over which period samples of
preheater feed, kiln feed (ex Stage IV cyclone) and clinker were taken
a t h o u r l y i n t e r v a l s . Coal samples were also taken periodically. Each
sample vas analysed for major oxides, fluoride, chloride, tr’a20, K20 and
SO3 using an XRF analyser. Ultimate and calorific value analyses were
also performed on :he coal samples.
Throughout each test period and, in most cases, for a period before the
test began, kiln operating conditions were monitored. Aver age kiln
conditions, and the range of conditions for each test are detailed in
T a b l e 2 . Tne results of chemical analyses of Stage IV material are
presented graphically for each test to show the variation with time
together with selec:ed process data in Appendix I.
During each test a number of plant measurements - air flovs, shell, gas
and material temperatures - vere completed, and a kiln operation log
maintained in order to build up sufficient information for heat and mass
balances. This raw data is summarised in Appendix 2, but in the context
of the alkali cycle studies this information is relatively meaningless
as the dominant factor in the overall heat balance vas the raw meal feed
rate vhich varied significantly from test to test, notably as a function
of whether the raw mill was in operation. Additionaliy, o v e r t h e t i m e
period covered, modifications were made to the top stage cyclones which
changed the external dust cycle for the system.
4 . EX?ERI.%ESTAL F!XSULTS
4 . 1 F l u o r i d e s
Average fluoride levels on a loss free basis for each test are
given in Table 3 together with the ratios of Stage 4 material and
c l i n k e r f l u o r i d e l e v e l s t o t h e f l u o r i d e l e v e l o f t h e p r e h e a t e r
feed material. The level of fluoride in Stage IV is generally
1.15 to 1.45 times that in the preheater feed indicating low
l e v e l s o f r e c i r c u l a t i o n . At such low levels of recirculation and
i n i t i a l i n p u t i t i s d i f f i c u l t t o b e d e f i n i t e a b o u t t r e n d s , b u t
plots of this data - Figure 2 - i n d i c a t e i n i t i a l l y a s l i g h t
decrease in average recirculation with increasing temperature,
folloved by a climb back to the original level. This pattern has
been seen before in experimental burning of mineralised clinkers
on the dry process. Experience here suggested that fluoride
volatilisation is more dependent on the potential flux level in
the mix than on material temperatures (Table 4). It is known that
an increase in flux level vi11 reduce component volatilities due
to changes in diffusion rate and reduced surface area, and so it
is possible that in the longer term over the lower temperature
range the effect of increasing flux level vith temperature has a
greater negative effect than the straight forvard volatility/
temperature considerations for this component.
At higher temperatures the recirculation rises back up to its
previous level, as temperature effects take precedence. These
trends are confirmed by the way in vhich fluoride levels in
clinker and preheater feed are similar at low temperatures, but
clinker levels lower than those of the preheater feed at higher
temperatures. Plots of Stage IV material fluoride level against
X0x level for each individual test (Figure 3) also suggest a
slight increase in recirculation with temperature over this short
time s c a l e .
There is no indication of any change in fluoride recirculation
level being brought about by variation of the kiln back end oxygen
l e v e l .
These observations cannot cover the situation where there is an
excess of alkalies over sulphate. In this instance alkali
fluorides can form from CaF2 and so a different trend would be
anticipated.
4 . 2 C h l o r i d e s
Initial comparison of the proportions of chloride in the Stage IV
material with X0x level for individual tests suggests a stable or
s l i g h t l y f a l l i n g l e v e l o f c h l o r i d e i n S t a g e I V w i t h i n c r e a s i n g
temperature (Figure 4) . However, higher X0x levels were generally
associated with higher raw meal input levels and a lower coal to
c l i n k e r r a t i o o v e r t h e s e t e s t p e r i o d s . This gives a lower total
chloride input to the system and so the lower Stage IV levels would
seem to reflect the lower input quantity. A S c h l o r i d e i s v o l a t i l e
at relatively low temperatures it can evaporate before the burning
tone, and so has a short cycle time. Figur? 5 compares the test
average da:a for the ratio of Stage IV to total input chloride
quantities and shows a slowly increasing chloride cycle vith
temperature, but this cycle is basically a large cycle with this
ratio falling between 20 and 30. There are also indications that
at the higher NOx levels the chloride cycle had not reached
equilibrium as Stage IV chloride levels were still rising with
t i m e a t r e l a t i v e l y s t e a d y NOx l e v e l s .
During the time period i n which these tests took place the Works
were still maintaining a regular preheater cleaning campaign to
control preheater build up, and the regular seni-flush situations
vhich this incorporates may have helped to control the S:age IV
chloride levels in the lower half of the predicted range.
Certainly it has been noted at Elope t h a t o c c a s i o n a l l y c l i n k e r
s a m p l e s c o n t a i n h i g h (+ 0.1X) l e v e l s o f c h l o r i d e . Furthermore,
t h e h i g h e s t t e s t a v e r a g e c l i n k e r c h l o r i d e l e v e l (0.162) vas n o t e d
in Test 1, during vhich period the kiln was unstable.
This is no evidence that modification of the kiln atmosphere by
moving into reducing conditions causes any change in chloride cycle
as the Stage IV to total input chloride ratio for Test 5 is very
similar to those from Tests 1 and 2 which had similar NOX levels.
4 -3 Potassium
The potassium (K20) cycle measured in the Stage IV cyclone during
these tests vas betueen 3.5 and 6.5 times the input level from the
rav meal. AS the proportion in coal is relatively small and vi11
not vary very much it has been ignored in these studies in order to
s i m p l i f y t h e e x e r c i s e . Figure 6a presents average data for each
test for the ratio of K20 in Stage IV material to that in the
preheater feed, plotted against average NOx level. For the normal
oxygen tests, this K20 ratio can be seen to be increasing (from
3.85 to 4.4) as NOx rises from 900 to 1,400 ppm. For the moderate
o x y g e n t e s t s t h e p i c t u r e i s l e s s c l e a r v i r h t h e r a t i o s f o r t h e lov
(Test 3) and high NOx (Test 6) :ests being similar vith a sharp dip
in Test 1, at the medium NQx level . It has previously been
suggested that K20 vi11 pre ferentially react vith chloride to form
a lov temperature cycle. It is also noticeable that the test
which does not fit in with the general picture - Test 3 - also has
a very high chloride level in Stage IV. Assuming that the
preferential reaction of K20 in Stage IV is vith all the available
chloride it can be seen that 65 to 752 of the potassium in Stage IV
will be bound to chloride. This cycle is a low temperature cycle
and can only be controlled by use of a bleed system.
K20 vhich has not reacted with chloride will nov react to form
sulphates. Table 6 also includes the ratios of K20 as sulphate in
Stage IV to K20 in the preheater feed. In this case the level of
K20 as sulphate in Stage IV rises from 1.05 times the K20 level in
the preheater feed at low #Ox levels to 1.24 times the preheater
feed level at high NOx levels. At both moderate and normal oxygen
levels this ratio increases as kiln NOX level rises. At the lower
NOx levels (850 to 900 ppm) the indications are that potassium
sulphate passes through the kiln without becoming involved in an
internal cycle. In fact at these temperatures, it is likely that
some Na20 becomes involved in the chloride cycle, as insufficient
potassium was measured in Stage IV to totally account for the
measured chloride level. These ratios are plotted in Figure 6b,
and the trend shovs up clearly. The K2S04 ratio for the reducing
conditions test (tes: 5) is slightly higher than those of the other
tests at 1,200 X0x level, but this increase is too slight to be
convincing proof of an increased cycle under reducing conditions.
Figure 6c plots the average ratios for each test between the K20
levels in clinker and preheater feed. This clearly shows that at
low NOx levels the system is in equilibrium in terms of K20,
however as the NOx level rises the output level of K20 falls belo=
that of the input. By an EiOx level of 1,400 ppm this inbalance
is approaching 202. Bowever, with the onset of reducing
conditions this inbalance approaches 50f. There art two possible
explanations for such an offset betveen output and input levels.
Firstly, it is possible that a build up of concentrated K2SO4 and
KCL is developing; this material sets on the surfaces vi:hin the
preheater and so prevents the material re-entering the cycle.
Secondly, there is a loss of K20 from the system. This may pass
to atmosphere through the stack, or be collec:ed within the raw
mill and precipitators and be returned to system as part of a long
term external cycle.
4.4 Sodium
Test average data for Xa20 levels - on a loss free basis - around
the kiln system are presented in Table 7, showing that the Na20
level in Stage IV is between 1.6 and 2 times that in the preheater
f e e d . Figure 7a plots the ratio of Stage IV Na20 to preheater
feed Na20 against NOx level. This suggests that initially the
r a t i o f a l l s s l i g h t l y a s NOx r i s e s b e f o r e c l i m b i n g a g a i n . In the
previous section it was suggested that at low NOx levels some Na20
reacts with the chlorides so becoming involved in the low
temperature cycle. Whilst only low proportions of the available
Ka20 - possible 10% - become involved in this way, it can still
s i g n i f i c a n t l y i n c r e a s e t h e t o t a l Na20 c y c l e . I n F i g u r e 7b t h e
r a t i o o f Na2S04 i n S t a g ? IV - as calculated from a chloride,
potassium and sulphate balance - to preheater feed Na20 is
p l o t t e d . This shows an increase in ihe cycle derived from Na2SO4
as NOx increases. The data suggests that the Stage IV Na20 level
- as SO4 - rises from about 1.35 times the level in the preheater
f e e d a t l o w NOx t o a b o u t 2 . 0 t i m e s a t t h e h i g h NOx l e v e l . T h e
results of moderate and normal oxygen level tests suggest that the
recycle can be reduced slightly by operation at higher oxygen
leve 1s , although this is not born out by the low oxygen test.
AS with K20, clinker output and preheater input Na20 levels are
Salanced a t l o w NOx l e v e l s , b u t a s t h e NOx l e v e l r i s e s a b o v e 1 , 3 0 0
t h e l e v e l i n c l i n k e r f a l l s q u i c k l y ; being betveen 20 and 30% lower
than the input level at 1,400 ppm NOx. This suggests that above a
certain temperature l e v e l Na2SO4 r e c i r c u l a t i o n l e v e l s a r e s t r o n g l y
temperature dependant. As Na20 is almost completely present as
Ira2SO4, this makes it possible to control and in some cases signifi-
c a n t l y r e d u c e t h e fia20 r e c y c l e b y conirol o f k i l n c o n d i t i o n s .
4 . 5 S u l p h u r
The level of sulphur - calculated as SO3 - measured in Stage IV
material and in clinker was very variable during the course of
each test as the levels react strongly to changes in both kiln
temperature and atmosphere. However, average values for the
samples taken around the kiln system for each test - given in
Table 8 - show a more consistent picture. The ratio between
sulphur as SO3 in Stage IV and in raw meal is plotted against kiln
NOx level in Figure 8a and shows that over the temperature range
investigated the total sulphur cycle rises from 1.6 to 2.6 tonnes
the sulphur input from the raw meal, rising as the NOx level
r i s e s . There is also a substantial increase in cycle once
reducing conditions are encountered - from 2.0 to 3.0 at
1,200 ppm NOx.
In the previous two sections the alkali sulphate cycles have been
discussed. AS these cycles increase only slowly with temperature,
these effects have been removed from the sulphate cycle by
calculating the amount of sulphur likely to be present as alkali
in raw meal and Stage IV and subtracting these from the total
quantities. The remaining figure can be considered to be the
sulphur which takes part in a calcium sulphate derived cycle; at
ilope this makes up approximately two thirds of the sulphur in
Stage IV. In this case the ratio rises from about 2.5 at low NOx
levels to around 4 at an NOx level of 1,450 as decomposition of
CaSO4 i n c r e a s e s . This cycle also increases quickly as the kiln
moves into reducing conditions; from about 3.1 to 5.5 under the
t e s t c o n d i t i o n s .
As in the previous two sections at low NOx levels the sulphur
output in clinker is approximately in equilibrium with that in the
raw meal, whiist as NOx rises above 1 ,300 ppm clinker sulphur
levels are lower than the inputs. Study of the data from
individual tests shows that after a sharp rise in temperature the
sulphur cycle initially responds very quickly but takes several
h o u r s t o s t a b i l i s e . This suggests that if the kiln is held stable
at higher temperatures the recycle ratio is likely to rise even
above the levels measured to date, and an external cycle will
develop. In reducing conditions the clinker to raw meal sulphur
ratio also drops substantially, from equilibrium to 0.55 when
operating at a 1,200 ppm NOx level at the kiln back end.
5. GZERAL DISCUSSION
The results indicate that with improved control of the kiln and
operation at lower temperatures and under steady oxidising conditions
it would be possible to reduce the alkali levels in Stage IV by a
moderate amount, and the sulphate level significantly. Over the
temperature range investigated the K20 level in Stage IV material was
reduced by about 10% at the lowest temperatures, whilst Na20 and SO3
levels in Stage IV material both fell by over 302. It must also be
recalled that the highest kiln back end NOx level that was targetted
was 1,400 ppm. Shortly before this test work began the kiln was
commonly run at an NOx level of about 1,800 ppm, and when an NOx
monitor was first installed NOx levels of about 2,500 ppm were common.
At that latter NOx value SO3 levels of up to 7.0% were recorded as
compared to the figures of 2.4 to 2.7 obtained during the low
temperature test work. A similar effect on Stage IV SO3 level was
observed during the new Oxford Works Simulation Trials at Plymstock in
1980 lg, as shown in Figure 9, although in this case extra iron was
added to the raw mix to permit the large reduction in burning zone
temperature. Overall the general trends and size of cycle for each
component fit in with theoretical studies for the vapour pressure v.
temperature relationships (Figure 10).
During the early days of high level control test work it was noted that
raising the measured kiln back end oxygen level from its previous normal
level of about 1.5% to around 2.3 to 2.5% resulted in considerably more
stable kiln operation. This was presumably a two tier effect, as a
normal level of 1.5% gave the potential for the kiln to dip into
reducing conditions when any disturbance occurred. The first effect
of this would be to modify the flame and hence temperatures around the
system. Secondly the reducing conditions vould strip volatiles -
notably sulphate - from the system, so upsetting the equilibrium and
modifying the quantities of low temperature flux and increasing the
likelihood of high levels of build up around the kiln system. This
e f f e c t o f o x y g e n o n s u l p h u r l e v e l s in clinker has also been noted at
Northfleet Works 2o d u r i n g t e s t i n g o f an SO2 continuous measurement
probe, and at Westbury. In the first case oxygen levels were
deliberately raised in order to stabilise clinker SO3 levels to improve
the consistency of cement quality, whilst in the latter the oxygen
level was reduced in order to increase the sulphate and alkali cycles,
so allowing the control of alkali levels on these wet process kilns.
Stabilization and reduction of the volatile cycles will lead to more
c o n s i s t e n t c l i n k e r q u a l i t y , and there will be a lower and more
consistent heat sink on the front end of the kiln resulting from the
e v a p o r a t i v e l o a d 21 3 22. However, this may be partly offset by the
reduction in low temperature flux level at the rear of the kiln.
Further study would be necessary to investigate this.
In the past most methods for the prediction of volatile recirculation
have been based on the oxide input levels, without taking real account
of their inter-dependancy and the forms in which the recirculation
develops. The results of this exercise clearly show the need for a
more detailed breakdown into the components of the volatile cycles.
kiiilst early studies by Research Division did take this approach, 23.
The installation of ‘Linkman’ high level control systems will give
increased kiln stability and permit improved studies of volatile
cycles . A further exercise on a dry process site with excess alkali
would be of benefit in expa riding t h i s s t u d y t o c o v e r t h e compl?te r a n g e
of possible volatile components.
6. PR..C?IC.AL I.QLICATIOWS FOR ROPE WORKS
Tne da:a shows that the major significant cycle at 'dope is calcium
sulphate based. This cycle increases markedly with increasing
temperature and also increases greatly with the on-set of reducing
conditions. Consequently it can be minimised by operation at lov kiln
temperatures and in an oxidising environment. It is not, however,
simply enough to avoid CO at the kiln back-end, as significant reducing
conditions can occur within the burning zone before an obvious increase
in CO is noted at the kiln back-end. Previous work has shovn that a
water wash sampling system tends to give an offset in oxygen analysis
and that this offset will depend on the water flow rate through the
sampling system. In general during the test periods this offset fell
betveen 0.6 and 0.8; a kiln back-end oxygen reading of 2.5% vas
equivalent to a true reading of 1.9% (offset 0.6). In order to
minimise recycle it is advisable to maintain the kiln back-end oxygen
reading - from the existing kiln instrumentation - between 2.0 and
2.5%. Kiln front end temperatures should be at the lowest level
compatible with steady kiln operation and will depend on the rav mix
chemistry and condition of the firing system, but is likely to
generally fall in the back-end NOx range of 800 to 1000ppm.
It is significant that the periods when kiln operation is most likely
to fall outside these ranges are during the routine cleaning
operations, vhich is also the time when the concentrations of volatile
components within the kiln are likely to be the highest. Extra
attention to kiln operation during these periods should result in
minimisation of volatile retention, vhilst lack of attention is likely
to cause the majority of the potentially volatile components cleaned
from the preheater to be driven back and redeposited within the system.
In order to fully control kiln operation at these times it is necessary
that the kiln burner be notified before cleaning commences.
7 . COSCLCSIONS 6 KECOM?fENDATIONS
The test results indicate that the chemical proportions of the minor
constituent volatile components at Hope lead to the following cycle
levels in stage IV meal.
1 . The typical fluoride cycle level is 1 .2 to 1 .4 times the input to
the system and does not change substantially as the kiln temperature
or atmosphere is modified, over the range studied.
2 . The chloride cycle is 20 to 30 times the to:al chloride input and
increases slightly with increasing temperature, although this may be
due to improved kiln stability at higher temperatures. The ch lor ide
cycle is not modified by wide changes to kiln atmosphere.
3 . Chloride in the cycle combines with potassium where available.
Eowever , at low temperatures - equivalent to NOx levels of below
1,000 ppm - some sodium is also involved.
4 . The chloride cycle is a low temperature cycle and cannot be
significantly modified by variation of kiln conditions.
5 . Tne total potassium cycle is approximat ely 3 times the input level,
however about two thirds of this is present in Stage IV in
conjunction with chloride and so cannot be controlled except by
incorporation of a bleed system.
r0 . About one third of the potassium in Stage IV is either feed based on
its first passage through the preheater or derived from a potassium
sulphate based cycle. This cycle ratio varies from 1.05 (minimal
recycle) at 900 ppm kiln NOx level to 1.25 at 1,400 ppm NOx (25%
recycle 1. This portion can be controlled by operation at low
temperatures,
7 .
8 .
9 .
10 .
11.
1 2
1 3
The sodium cycle level varies between 1 .2 and 2.0 times that in the
rawmeal over the temperature range examined.
At lou temperatures some sodium becomes involved in the low
temperature chloride cycle and this boosts the sodium cycle by
about 10%.
The majority of the sodium in the system is involved in a sodium
sulphate based cycle. This is strongly temperature dependent, and
the rate of increase also appears to be increasing with temperature.
Over the temperature range investigated the recycle rose from 1.35
times the level in the feed at low temperatures to 2.0 times at
h i g h NOx l e v e l s .
T'ne total sulphur cycle is temperature dependent and rises from 1.6
to 2.0 times that of the input over the temperature range
investigated .
The alkali sulphate cycle has already been summarised in Points 6
and 9 and makes up about 35% of the total sulphate in Stage IV
material . These cyclic levels can be seen to be lover than the
t o t a l s u l p h u r c y c l e l e v e l s .
Tne calcium sulphate recycle is strongly temperature dependent and
rises from about 2.5 times the level in the feed at low NOx levels
t o 4 t i m e s a t h i g h ( 1 , 4 5 0 ppm) NOx l e v e l s .
The calcium sulphate cycle is also increased by a move into a
reducing kiln atmosphere. At about 1,200 ppm NOx the cycle
increased from 3.1 under oxidising conditions to 5.5 times the
feed level under reducing conditions.
14 . For potassium and sodium there are indications of a slow but steady
increase in losses of these components from the preheater system
as temperatures increase. This may become part of an external
cycle or may be lost to atmosphere. This could be established by
a longer term study of the levels of these components in the
precipitator and stack dusts.
15. Sulphur is in overall balance within the system below NOx levels
of 1,200 to 1,300 ppm, but above this level the loss increases
sharply with rising temperature. Again this may become part of
an external cycle or may be lost from the system, however in this
exercise no precipitator or stack dust samples were collected so
this cannot be confirmed.
16. When the kiln atmosphere moves into reducing conditions the losses
of alkalies and sulphur from the kiln system increases sharply.
In vieu of these conclusions it is recommended that, at hope:
1. Kiln back-end oxygen level is maintained at 2.0 to 2.52
(as measured 1.
2 . Kiln back-end NOx levels are mainta
the most appropriate NOx level will
chemistry.
ined b e low 1200 ppm, although
depend on detailed raw mix
3 . Communication between kiln burner and personnel cleaning the
preheater be improved.
4 . During cleaning operations short term reductions in raw meal feed
which avoid the inception of reducing conditions will be
beneficial in the longer term.
REFERENCES
1.
2 .
3 .
4 .
5 .
6 .
7 .
a .
9 .
G. Mussnung 'Contribution to the Alkali Problem in Suspension
Preheater Kilns (Bumboldt Kiln)‘. Annual Meeting of the Heat and
Energy Committee of the German Cement Makers Association,
8 December 1961, Dusseldorf.
'Coal and the US Cement Industry, Parts 1 and 2.' World Cement
Technology, Jan/Feb. 1982 and March 1982.
Weber 'Heat Transfer in Rotary Cement Kilns' Section 4.5.
3aspe1, Lorimer, Southern, Taylor 'Blue Circle High Level Kiln
Control' IEEE 1987.
A. Lorimer 'Fuel Savings Arising from the Operation of High Level
Control at Elope Works', Research Division, Process Development Dept.,
F N 86/68.
Haspel, Taylor, Kerton 'High Level Kiln Control based on NOx Monitoring'.
Paper to Cetic Chemical Commission Mee:ing, Liege, June 1985 (ETN 85/21).
Locker, Spring and Opitz 'Reactions associated uith kiln gases.
Cyclic Processes of Volatile Substances, Coatings, Removal of Rings'.
VDZ Congression on Process Technology of Cement Manufac:ure, 1971.
Davis and Longman 'Design and Experiences with Bypasses for Chloride,
Sulphate and Alkalies'.
Bra-, A.W. 'Chemical Consequences of High Efficiency Systems' Group
Technical Conference 1976.
10. Danoe and Steuck 'Behaviour of Volatile Matter in Cement Kiln Systems'
FLS Publication.
11. Hawkins and Wilson 'Fluorine Containing Phase causing Blockages in
Suspension Preheaters'. American Ceramic Society, Pacific Coast
Regional Meeting, Los Angeles, Oct. 31, 1977.
12. Polysius Review NO. 58 'Chlorine and its Behaviour in Preheater Kilns'.
13. Goes and Keil 'The Behaviour of Alkalies in Cement Burning'.
Tonindustrie-Zeitung 84(8) 125-133, 1960.
14. H. Carlson 'The Behaviour of Alkalies in Cement Raw Materials during
the Burning Process'. Rock Products Cement Industry Operations
Seminar 1965.
15. Goldman, Kreft and Schutte 'Cyclic Phenomena of Sulphur in Cement
Kilns' World Cement Technology, November 1981.
16. Hatano 'The Behaviour of Sulphur in Suspension Preheater Kiln Systems'
Zement Kalk Gips, l/1972, p. 18-19.
17. Etoc P 'The Cement Kiln - An efficient Trap for Sulphur'
Ciment, Beton, Platzer, Chaux (701) 210-213, 1976.
18. Ritzemann 'Recirculation Problems in Rotary Kiln Systems' ZKG(8),
338-343, 1971.
19. ‘-Lxperimental Prodquction of a Minor HESC at Plymstock Works, in order to
Investigate The Potential froblems Associated with The Production of a
Similar Material at a New Oxford Works' Eng.RD TN 81/13.
20. A Lorimer 'On-line SO2 Monitoring: Assessmen: of RDUV and Electrochemical
Cell Systems at Northflee:: May to October 1984'. Research Dept. Em 84/21.
21. D W Haspel 'Cement Kiln Alkali/Sulphate Cycles under Equilibrium
Conditions', Research Division, Process Development Dept., Fh'/'84/93.
22. D G Stenson 'Factors affecting Sulphate and Alkali Cycles in Rotary Kilns
and the implications of these Effects with Respect to Process Control'
Research Dept. ETN/84/13.
TABLE 1 - EST TARGET CONDITIONS
Test No.
1 1,200 1.8
2 1,200 2.5
3 800 1.8
4 800 2.5
5 1,200 AS required
6 1,400 1.8
7 1,400 2.5
NOx level BE02 level co- - -
Nil
Nil
Nil
Nil
Positive
Nil
Nil
TASL.E 2 - TEST AVERGE CONDITIONS
Test No.
1
2
3
4
5
6
7
Average
NOx l e v e l
1,244
1,214
9 9 5
a68
1,223
1,462
1,365
Range of
NOx values
573 t0 1,938
840 to 1,587
5 2 7 to 1,472
543 to 1,330
9 0 9 to 1,418
1,008 to 1,780
1,100 to 1,608
Average BE02
level
1.67
2.25
2.11
2.47
1.57
1.37
2.72
Range of Ave CO
BE02 value level- -
1.20 to 2.05
1.94 to 2.67
I .50 to 2.80
I .37 to 3.08
0.9 to 1.76
0 . 9 to 2 . 2 8
1.88 to 3.14
TABLE 3 - AtERAGE FLUORIDE LEVELS FOR EACH TFiST (LOSS FREE BASIS)
Test No.
I, Fluoride in
raw meal
Z fluoride in
clinker
1 2 3 4- 5 6 7
0.109 0.109 0.109 0.109 0.155 0.186 0.185
0.105 0.105 0.13 0.11 0.16 0.16 0.16
2 fluoride in 0.126 0.128 0.154 0.142 0.179 0.235 0.218
Stage IV
Ratio o f fluoride in 1.16 1.17 1.41 1.30 1.15 1.26 1.18
Stage IV to raw meal
Ratio o f fiuoride in 0.963 0 -963 1.193 1.009 1.032 0.870 0.845
clinker to raw meal
TABLE 5 - TEST AVE.RXE CHLORIDE LEVELS (LOSS FREE BASIS)
Test No. 1 2 2 4 5 6 7
1. % Chloride input 0.060 0.060 0.063 0.064 0 -059 0.059 o.oc+
2. X Chloride clinker 0.16 0.14 0.009 0.017 0.008 0.008 0.010
3. % Chloride in Stage I V 1.295 1.405 1.702 1.419 1.346 1.519 1.627
4. Ratio 3:l 21.6 23.4 27.0 22.2 22.8 25.7 25.4
TABLE 6 - EST AVER;IGE KpO LEVELS (LOSS FREE BASIS)
Test
1. % K20 in raw meal
2. % K20 in c linker
3. % K20 in Stage IV
4. % K20 in SCage IV
as chloride
c2. % K20 in Srage IV
as sulphate
Ratio 3:1
Ratio 5:l 1.158 1.223
Ratio 2:l 0.86 0 -89
1 2
0.65 0.622
0.565 0.551
3 4 5 6 7
0.623 0.636 0.651 0.646 0.678
0.64 0 -615 0 -465 0.53 0.56
2.505 2.618 2 -749 2.452 2.387 2.811 2 -976
1.752 1.851 2.089 1.781 1.585 2,028 2 -133
0.753 0.761 0.66 0.671 0 -802 0 -783 0.843
3.85 4.21 4.41
1.059
1.03
3 -85 '5
1.054
0.97
3 -667
1.232
0.68
4.351 4.389
1.212 1.243
0 -82 0.83
Test
TAELE 7 - TEST AVERAGE NA20 LEVELS (LOSS FREE BASIS)
1 2 3 4 5 6 7
1 . % Na20 in raw meal 0.218 0.20 0.202 0.202 0.233 0.231 0 -277
2 . 2; Na20 in clinker 0.211 0.207 0.221 0.227 0.172 0.195 0.196
3 . % fia20 S t a g e I V 0.329 0.294 0.327 0.323 0 -330 0.471 0.499
4 . % Na20 in Stage I V 0.005 0.006 0.033 0.052 0.00 0.011 0.00
as chloride
5 . % Na20 in Stage I V 0 -324 0.288 0 -294 0.271 0.330 0.460 OTFFJ
a s sulphate
Ratio o f 3:1 1.509 1.470 1.619 1.599 1.416 2.039 1.801
Ratio o f 5:1 1.488 1 .44 1.455 1.342 1.416 1.99 1.801
Ratio o f 2:1 0.97 1.03 1.09 1.12 0.74 0 -84 0.71
TABE 8 - TEST AVEUGE SO3 LEVELS (LOSS FREE BASIS)
Test
1 . 2, SO3 in raw meal
2 . % SO3 in rm (CaO)
3 . % SO3 in clinker
4 . % SO3 in Stage IV
5. % SO3 as CaS04 as
in Stage IV
Ratio 4:l
R a t i o 5:2 3.043 3.199 2.416
R a t i o 3:l 0 -985 1.035 1.023
% a s CaSO4
1- 2 3 4 5 6 7
1.53 1.369 1.417 1.419 1.473 1.668 1.696
0.696 0 -582 0.627
1.507 1.417 1.449 1.485 0.838 1.400 1.425
3.176 3.193 2.356 2.710 4.433 4.426 4.005
2.118 1.862 1.515 1.812 3 -326 3.166 2.644
2.076 2.142 1.663 1.910
2.932
1.047
66.9
3 .OlO 2 -653 2 -361
5.373 3 -856 3 -470
0.569 0.84 0.84
66.7 58 .3 64.3 75 .o 71.5 66 .o
X
HOPE WORKS No 2 KILN: RELATIONSHIP -BE;TwEEN NOx AND LX&T
x
x
x hourly ATerAg datafrom 3/5/85
0 daily AVel%gt dAtA
August 7985
I r I
730 1350 1400Burning Zone Temperature ( "cl (av.Worka pyru rending)
I
1450
-.-
i-_
. .
..-
.----L-~
--.-
-
_._..
. -
_.
-..-_
..-A----.
‘-.
..: -_~
. _
----+_
__
_-.
.
- __.
- .
-L-.----d-h. .
----!
. --
i-.
-.-.
-.._. __ -
.~
~~
p---~
a -
;-/
1-- _
__
!I
,--
_,
!
/I
:_----
--.-
i ..-- ~-.-
1-.
; .
._ _
. _
. ..-:.-_&
--
L-
~---
.-.-:
.
-.
_ -:..-~
--I
I_
: _
. _
_..
; --
-----
7----
.- ---I
III
“E
-p
----j
- ..---- ---. -----r‘----‘-
-..-
------------:
_ _-_
--_ _-.-._I
_[ ‘-kII+x*y-----/
j
IIi
-.. _---__--._-__ _
. ; _____. r( __. * __ -
cn.
--+-~
Ii..-
+fi
----+--.
-__
- -i- -______;_
_I
II
II
-I:,.
C--_
-.----L _
_._
__
_--.-._
_- ----+
- +
--+
--
:------_i
--_- -
-/
- ---.
-_
--
_._
-
_ . _
_-
---
/--
--- --
.----
- . -.
.-.- __
-Q
L-
,L,..
--.-.--i- -_--iL
--
..-.‘ ___... .- ______ f_. _ _ -. . . ----+.-
- - - . - : . . __. - -I---- ----z_i~:~~z+:~
.l.x x.1: ; : 1-1: : : : 1:..----_d _- -----.
_ _ . _. _ _ _ _ _ _-_ _ _ ----; _.- ..-.- _ ----_ _ . _ - __- .
- .:
_. .i
1 :-.:
- .._
_-:‘--
.. ‘.., _ __ .-. _ - - . . - --
--
--
i
-1 _..
_. _
_ _.
) .
.
:.‘.”: . .
_-_ _ _ ._ - - . .
_.-.,
‘:.I . .._ ..-.. -.-.
! _
_ _
. .
._ _ . _ . -- . ..-
-_-.-- - ..- _.-Ii---
-”i-1 --
_ -. r _ __!___
-__. -.
, ~
-._: _. . . .
I.
.
. .._
-
I..--. -.I
_ . . ..
__. ,
_i
. _
. -
:’
‘..
.,-
-....-_..
I...
.
..-.i-.
.
. .
. ..i
-.
---
i--.--
‘o---.--
CD
-_ --
._
--_I_
--
---
_ __-_-
-
- --.
- -._
-----..
. ___
- - --
- ____
_ -._
_
----__
__...._ -.!.T.- -_---_- . ..-- - -_- -. - -.. -!A-- .-.. +.--L-. ..- - -- .-UiLX~ hd-u**,cI) j
t-
L-
4
.2 -
P -
!
.cj!i-- .-i-L_.-- : ._ - i._. -... ._ _ - _-._
_ - - .__ .__ .- .d
-’ m .A -.:-
I If
-_-_ __._ --.- .___ ----.--
-.--_-.-.---I
I:.
-.\
tI
qi
1..
Ii.. :
j_
----_
-_
_-.----
.-.---
’
-4
-:
j’ j
i .:
.
--
:
;.i
‘-.
--*y-T
--yf-‘y-
y.--_~
.;:+
-------
-;.-
L--
---;-
__
.__
. ---_
.-
.._ :
~: :
.: -:
.
; : : :
: --.-- - ---2 -
j : : : :: . :
Lb.r- I .:.:
..: f i.;,.:: -:; -:....:. i:: ;., ..-.:,:. i .I : .~
i ; :_ j ; ; : -i ; : :j _ : : : : ; ..: .’ --I ..: ; -. ..: .-: : ::
:.;;’ :
_: _. .- ~. _. .
; ::. -1..-
E :. : : i..: : -.=: y 1 ;..: i r .,
i :.I :_:. i..
634 PLY?WJ!OCK WORKS.. VARIATION OF SDLPHATE CYCLE WITH BZT
2c.b I I I300 4 0 0 500
so3 ex ntnge IV a8 of total SO, in feede (meal + coal)
X?PEE;DIS !
GUPHICAL REPRESESTATIOTS OF VARiATI04‘S IK
STAGE IV MATERIAL CklEYISiKV 0% A?i IYDIVIDOAL TEST EASIS
-.:E: :. ::. i .-:a-.-. .
: I:
: : :
_ _ .i -1 + :-
: ,: :
.-
;:L.---Ii :_:1 1’.----+-‘,- _:. :-L ..I ..i ,.vE-. : .Y.-.t :.i;iwt :
+ .’&&g.L_iz ::- :?---+L;:
;--.
++-jtL--;.!+---t-:E---L
----... ---.-
---i
----
-.7--.- -...A--+...--.- ~.~-
:----j - ..-- - . .._.._ .._ . . -_ -- ; . -..A----..+-.L- _-.-
I
--i-_..---_7_ : : :------
: : I :: :--+- --~
f !
1: :rc’-r ; )
:: j: :
: : :L-1: :/-
--- : -: ::
: : : ‘.:--:- \I : 1 : :.:
: ::j
_ ‘.--: 7 ..:_: ._- ---2 _ Le. : ._ _. ..:_ r; : -: .: .: -I. ;:-.- . _ _: : . . . . _-.. _..__. -_- -.
. - ._I.. -- - -.--- ---___ --..-
., :
:: ::- -_ .‘; I’-,.:: - ‘:Y. i - ‘..f --z
L : : - : . . .- : . - -
i
:A.
._” : :.: :‘I : :”
:
: :k ---
:;..: 1 :--.-. -.-.-1 ::.. ::‘::
:: : : _::
T----y :--A.-L.:
1 : ::-
. .
.: ::.1 ::, i : i.
: .:
: ; .: .: :7 : :
. . __: I . . : :
-.:
,.:: : ii...;.i :‘.:
: : 24, ., . : ) 1 .;. ..i ..: (-.
A 4
Ty : j j : : ..i : .-_; .-: ::“. : : :j . .._..._
:.. :/. \ :/ : : : i:: : : :.j 2;. _.... .; _;:
: ..:. : r1--.., -.--;: ..: . . : -: : : . . .: .: ..: - .=
?-..---A .- - .~ . .._..._- j i _ ‘~ ..~ : lr. :.
4.1:
_.:z;:
i ..:. : .\-. -_ :_..
: : : :..:: : _--. :. : .-.-- :.. --
APPENDIX 2
PLANT .?EASUREiHEATS
.9/?/37
3
3-27
l220
23-o
I-P?
.-
t
~0,7
lG7
q I-?
--
..-
.-
-
lGl3
3 -+a-
20.3
Kc1
I so
I133
---I-S-11QO 536
33t BLC,I 822 I
I
2
3
4
s
6
‘31
APPENDIX1
Material %Feed % B.E.
Na20
K20
S O 3
cao (caSO4
Cl
If
O-2
0.6
1 . 3
0.37
0.4 (x2)
6.0 (x10)
6.5 (x5)
0.74 W)
F
MJOI -
0.19
EOPE h7XK.S ALKALI CYW
BuRNI% ZONE c.kimIcAL LOAD
TADER 4UILIBRIUd COhDITIONS
% Prcduct 1982 clinker AbsoluteAverage % Recycled
0 . 2 0.25
0.6 0.55
1 . 3 1 . 3
0.37 0.37%
0.2% (xl)
5.4% (x9)
5.2% (x4)
0.37% (xl
2.0%
* Eetemined
13.17%
fran sulphate balance.
Assuming the average heat requirement to vacourise - deccxqmse alkalis
averages 800 kcals/kg (600 to 1000 kcals/Ig[l] 1 then average aBali
vapourisation load on th,n burning zone is 100 kcah/kg.
[ll Vapourisation only - No decmpos ition of alkali salts.
m 84/93
Over a period of years, various extimtes of the heat required to
drive off the alkali/sulphates in the burning zone have been made. The
majority are in the order of 100 kcals/kg. However ETIU 83/13 has sho+.n that
this can easily tax-y on a short term basis by i 50 kcals/lcg due to a minor
disturbance in-the Burning Zone Tarcjerature. This note references scxne of
the various source& on this subject.
1.
2.
3.
"Heat Transfer in Rotary Kilns" Weber. P.
ZIGS Spcial Publication X0 9.
Alkali cycle equivalent to 100 Kcals/kg clinker.
Lepol Grate Heat Transfer Mechanism
D-W. Haspel June, 1973
ikxaxA 005
At least 70 kcals/kg clinker of heat are recovered as a resu+lUor the
condensation of alkalis/recrmbination of SO3 on the Lepl grate.
Hope Works Alkali Cycles - See Appendix I.
The mean heat required to vapourise the alkali/sul?hates at Eope is in
the order of 100 kcals/kg. A further 10 kcals/kg is involved in the
melting/fusion of the salts.
The exothermic clinkering rcuctions cccuring in the burning zone are
equivalent to -97 kcals/kg (typical 1982).
APPENDIX II
HOPE 5XRKS CLINERING REACTIONS
~thermic Reactions:-
Heat of Form&ion
C3S
C2S
C3A
C4M
-126.2 kcal/kg
-174 kcal/kg
- 3.7 kcal/kg
-20.1 kcal/kg
Total
Hope % (1982 Av)Clinker Canposition
62.7
9.2
10.4
7.8
k&b/kg clinker
-79.1
-16.0
- 0.38
- 1.57
90.1% -97.05 km&/kg clinker
Note heat required to prcduce C3S fran C2S is +2.8 kcals/kg reactant
Endothermic Reactions:-
Alkali Recycling tlO0 kcals/kg
Latent heat of Z&ion (circa 10% of vapourising load) + 10 kcals/kg
ll0 kcals/kg
Net (Ekothermic/~doth~c~ + 13 kcals/kg
Useful Heat in Gases and Clinker Dust
Useful Heat in Gases (Sp Heat xA T) circa 0.17 x T = 17 kcals/kg/lOO°C
Useful Heat in Clinker (SP Heat x A T) " 0.30x T = 30 kcals/kg/lOO"C
APPENDIX Iv
Z-IBM! DISmmCE ?!SSCC3ATED WItTYI KILB CLEYNFG (HOPE)
Area to b= cledned. 8m (circumference) x 5m (length)
= 4Om*
AssumS thickness circa l/4 - l/3 m
Total rr&erial to be cleaned - circa 10m3
Assuming S.g of 0.8 - 1.0, Material hocked down 8 to 10 totes, of
which circa 20% - 30% are alkalis.
With additional heat requirenent to m&e clinker 300 kcaI.s/kg
This material is equivalent to 3 'Lonnes of clinker
(distrilxlt& over two hours?)
or5 tOMeS of feed
D. W. Has@
November 1984
APPENDIX III
PHYSICALC0NsmNE ASSCCIATEDWITE! ALKALI CYCLES
Latent Heat of Vapxrisation/Eemqmsition
Kcl +670 kcaldkg W)
K2s04 +563 kcals/kg W)
+1805 kcals/kg (D)
Na2SO4 t-733 kcals/kg W)
+2096 kcals/kg (D)
CasOi +675 kcaldkg (D)
v = VapxrD = Dissociate
Later&He&of Fusion
KC1 +96.6 kcals/kg (M-P. 722°C)
K2SO4 + 57.6 kcals/'Kg (M-P. 1069°C)
Na2SO4 + 42-S kcals/kg (M.P. 884°C)
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 7
Design and Experience with Bypassesfor Chloride, Sulphate, and Alkalis
DESIGB AND EXPERIENCE WITB BYPASSES FOR CBLORIDE, SULFATE .tvl, ALKALIS
By Xessrs P.. Davis and P-A. Longman
Blue Circle Industries, United Kingdom
1. INTRODUCTION
During the production of Portland cement clinker, some of the
minor components $n the raw materials and fuel, notably the alkalis,
sulphur and chloride compounds are volatilised in the kiln. These com-
ponents are then swept with the kiln gases to the cooler parts of the
kiln system uhere they condense. In the less thermally efficient pro-
cesses, such as the wet and long dry process, a significant proportion
of these volatiles can *escape' from the system either in the prccipi-
tator/5ag house dust or up the stack. In the Lepol or XL process,
which we have successfully operated for more than 20 years, fairly
high levels of volatiles can also be tolerated. This is partly
because the nodule grate is not a particularly effective scrubber and
partly.because precipitator and intermediate cyclone dust can be
discarded thereby lowering the volatile recirculating load.
Similarly, in two stage preheater processes moderate volatile inputa
can be tolerated.
However, in the more thermally efficient processes, such as the
four stage suspension preheater process, greater amounts are "trapped"
in the feed as It passes down the preheater and are carried back into
the kiln, where a proportion again evaporates. This repeated evapora-
tion and condensation leads to the gradual formation of an internal
volatile recirculating load until a steady state is reached(l).
-2-
When the first suspens'ioti.preheater processes were:-built In-tt.
1950's the importance of recirculating‘volatlles~was m.t fully appr
ciated and- a- number bf plants simply could- not run.&ecausc.of build
and blotikages at" thi Wla inlet and in. the--louer, stages: of the prc-
heater.
I,n some instances-the clinker produced uaa of unacceotable
qualitv because af its hinher alkali content in comoarlson ulth that
produced in the simpler, but leas thermally efficient processes.
Over the yeears, as a result ef studies made by both the plant
svooliers and the cement manufacturers (see references) an
understand$ng has emerged of the factors affecting the formation of
the_ volatile recirculatinn load in a four stage ausuension oreheater
process, and of the effect such a recircnlatlon has on plant ~4
mance and cement quality.
As a reaul.t, It is possible, when employing the four stage
suspension preheater process for cement manufacture to predict the
maxImum levels of chloride. alkalis and sdohate that can be tolerate<
in the raw materials and fuel. Where these levels are just exceeded
the situation can often be recovered, ad kiln operation and cement
qiiaLitp,ptob1en!s. avoided, by extr$cti-ng a proportion of the kiln gases
'befbre. tA#! preheatar such-.tI& a .sufficient proportion of the unwanted
volatile! components- are "bled" qut the system flowever, operation of
such a."bJeed" or Wla bypass,also depletes. the preheater of some of
Its he,- uith,the.reault. that -on-a susoension preheater process
the kiln bypass has to be llmited$to_about 25% otherwise there is
insufficient heat for effective preheating(2).
-3-
Bith the introduction of precalciners in the mid 1970's it vas
generally recognised that this limitation could now be overcome and
that by burning a substantial proportion of the total fuel in the pre-
calciner it would-be possible to bleed all of the kiln gases, if
necessary, and still achieve sufficient decarbonation and calcinatioa
in the preheater(3r4,S)* Moreover, whereas in a suspension preheater
process a fuel penalty of about 4 kcal kg'1 of clinker is incurred for
each 1% bypass, in the precalciner process this is roughly half at
around 2 kcal kg-l.
At that time, therefore, the precalciner pt'ocesi looked par-
ticularly attractive in this respect and partly for this reason'gained
videspread adoption. Since then operational'experience and results
have been obtained vhich have cast doubt on the effectiveness of the
kiln bypass on this type of process.
In Blue Circle Industries, in addition to operating a number of
conventioaal suspension preheater processes with no bypasses, UC have
experience in running one suspension preheater process fitted ulth a
small bypass to remove cnlorlde and two precalciner processes fitted
vith bypasses to remove sulphur and alkalis respectively.
In this paper, we outline the chemical factors which determine.
the volatile recirculating load in a four stage preheater process and
the effects this can have on kiln operation and cement quality. Our
experience in operating both four stage preheater and precalclner
kilns with and vithout by$asses and how the bypass performance com-
pares vith design predictions is-also discussed.
-4-
CFEMICZLL, PACTORS
2.1 Volatile Components
The two main factors which vi11 dictate uhether a kiln bppasz
necessary, and if so hov large, are:-
i) The total quantities of alkalis (sodiumGiAd potassium), color
and eulphur present in the rav materials aad fuel which vi11
determine the overall composition of the clinker.
ii)..,The volatility of these components in the kiln system which WI
determine-the nature of the volatile recirculating load.
The main source of alkalis is the clay and shale phases in the
secondary rau materials and in general the presence of al'alis in t1
primary calcarcous raw material or the fuel arises from coataf"~ -'ic
wtth argillaceous materials.
Chloride is normally present as alkali chloride in the raw
materials and fuel but the presence of organic chloride compounds in
coal or other fuels is possible.
Sulphur can occur as a variety of organfc and inorganic compounti
in both fuels and raw materials and in a variety of oxidation states.
The volatility of these components in the kiln system Is complex
and is dependent on the follouing interrelating factors:-
i> Whether the volatile components occur in the fuel or the raw
materials.
- 5 -
ii) The relative amounts of the total alkalis, sulphur and chloride
entering the system.
iii) The burnability of the mix, uhich can be influenced by the
overall chemistry of the clinker., the fineness of the raw feea
'and whether mineralisers such as fluorine are present.
iv) The burning environment in the kiln system, which vi11 be
influenced by (iii) above, the level of free lime required, the
nature of the fuel and firing system employed and whether carbon
and/or sulphlde is present in the raw materials.
2.2 Volatile Cycle
In practice, the volatile recirculating load in a kiln system
vi.11 gradually build up to equilibrium and it is customary for
researchers and workers in this field to estimate the final balance of
volatlles recirculating by regarding the build up in cycles. A number
of papers have been published on this subject (6-9) and this is an
approach which we have been using for some 20 years, uith the
assistance of computer programmes for the past 10 years.
In our current computer model the first cycle is regarded as
where fuel and feed first enter the kiln system. In general the vola-
tiles In the fuel are assumed to evaporate completely as the fuel com-
Susts, while of the volatiles in the raw materials, only a proportion
are assumed to evaporate - the remainder being retained in the
clinker.
-6 -
Of the volatiles that have been evaporated a certain propor:
(generally most) are assumed to condense on the feed in the prehe
such that In the secood cycle the material entering the burning zt
contains both recirculating volatile compounds and volatile compel
present in the raw materials.
For the second cycle a proportion of the volatlles in the raw
materials will again evaporate in the burning zone and the rentaind
stay in the clinker. Similarly, a proportion of the recirculating
compounds will also be evaporated uhile the remainder are retained
ihe clinker. With each ensuing cycle, therefore, the quantity of
volatile compounds recirculating and the quantity retained in the
clinker gradually builda up until the total quantity entering the
system via the feed and fuel equals the total quantity leaving c
system 'via the clinker and stack.
A simple illustration of this is shoun in Figure 1. Rouever,
tsoastruct such a balance it is necessary to have a knowledge of the
recirculating compounds being formed and the volatllities of both
these compounds and those present in the raw materials. Below, ue
.summarisf the information we have acquired from both laboratory
investigations and studies of full scale plant of the behaviour of
chlorine, sulphur and alkalis in suspension preheater processes. It
was on these data that we based the design of our bypasses for our
precalciner plants, and uhich in the light of our more recent
experiences now require modifying.
-7 -
2.3 Chloride
Virtually all the chloride input to a kiln system vi11 be volati-
lised at burning zone temperatures and in general less than 3% of that
entering the burning zone will leave via the clinkerc2).
During the process of evaporation and being swept down the kiln
the chloride will preferentially react with potassfrrm to form
potassium chloride and in general sodium chloride vi11 only form if
there is an excess of chlorine over potassium.
A very small percentage of this alkali chloride may escape up the
stack as fume or fine particles of dust but the bulk will condense out
on the feed.
By itself, potassium chloride till largely condense out in the
temperature range of 800 - 900°C and as a result it can often cause
blockages and form hard deposits in the back end chute or in the riser
pipe to the lower preheater stage. If sodium chloride is also present
the temperature range over which the chlorides vi11 condense till be
extended generally dounwards i.e. 700 - 900°C and in terms of kiln
operation this may present fever problems. A similar effect occurs in
the presence of sulphates.
2.4 Sulphur
The behaoiour of sulphur in the kiln is more complex than that of
chloride and is strongly influenced by the form of the sulphur and the
burning conditions.
-a-
In general, sulphides present in the raw materials wfll‘read~
oxidise and evqorate such.that most if not all are driven off by
time the feed reaches the burning zone. Calcium sulphate, whether
present in the raw materials or. fotmed in the kiln cycle, although
not particularly'oolatil,e, readily dissociates at burning zone tur
peratures particularly under:prevailing reducing conditions, and y
only a small proportion of this sulphate- is retained in the clinke:
Alkali sulphatea similarly dissociqte id's reducing cvirooment.
However, in an oxidising enviromaent they are'nore stable with the
result that up to 40%. of the total alLd.1 sdphates entering the
burning zone map be retained In the clinker,
It follows that the bulk of the sulphate retained in the clinks
is alkali based - either as alkali sulphate - @i?la)2S04 or as, It
alkali calcium sulphates such as calcium langbeinite 2CaSOf,.K2suq-
This is illustrated 19 Figure 2. . In contrast the sulphate evaporate
may be alkali sulphates, dissociated sulphates or oxidised sulphide.
This mixture vi11 condense and/or react over a tide range of tex-
peratures as it passes to the cooler parts of the kiln. SO2 gas vfl
readily react uith calcium oxide in the decarbonated feed at the bat
end of the kiln but any uhich is not trapped in this ny say well pa:
through all of the preheater and escape up the stack(lO*ll).
Most sulphate compounds will condense at temperatures of
900-1100°C. In our expeience if the alkalis and sulphates are more
or less in balance this condensation forms a light loosely bound depa
sit in the fourth stage and kiln inlet which can be scoured away by
-9-
passing feed or if necessary easily removed. Aowever, if there is an
excess of sulphate over alkalis the deposit can be more sticky and
harder to remove. Densified layers of calcium sulphate and sulphosi-
licates 2(2CaO.S102)CaS04 (Figure 3) may form which vi11 adversely
affect kiln performance and. require special cleaning
facilities(12r13). If fluorfne is present In the rav materials the
situation may be exacerbated by it promoting the formation of inter-
mediary compounds such as the fluorinated calcium dumim:e
(CllA7.CaF2), spurrite 2(2. CaO .SiO2 )CaC03 and various calcium sulpho-
silicates.
2.5 Alkalis
In general a substantial proportion of the recirculating alkalis
will be associated uith either the chloride or sulphate as discussed
above.
Houever, there ulll always be a tendency for some alkalis, par
ticularlp Na20, to be retained in solid solution in the main clinker
phases(14). The proportion of alkalis retained in this uap in the
clinker will increase if there is an excess of alkalis over sulphate
entering the system or if reducing conditions prevail in the burning
zone. Reductioa will lead to dissociation and preferential loss of
SO2 although with severe reductioa, alkali iron sulphide compounds
such as ?ZeS2 may form in the clinker which results in a greater
retention of alkali and sulphur in the clinker than is otherwise
expected.
In general up to 50% of allalis entering the burning zone as
alkalis oxides may be retained in the clinker.
- 10 -
If there is an excess of al.kali over sulphate uhere condensation
occurs at the back end of the kiln hard alkali carbonate based depo-
sits may form.
PRACTICAL IWLICATIONS
3.1 Kiln Operatioa
Published data, coupled vith our OM experience, suggests that
the formation of blockages and hard'deposits in the fourth stage and
kiln chute are likely to start presenting problems when the level of
chloride or sulphate in the feed material leaving stage 4 exceeds 1.5%
or 3.5% respectively. In addition such levels of sulphate may also
enhance ring formation in the kiln itself thereby restricting output.
The quantity and nature of the volatile recirculating load will
obviously vary from Works to Works, but in general practical terms in
order to avoid exceeding the above limits it will be necessary to
restrict the total volatile input to the system, when &pressed as a
percentage of the clinker output, to 0.025 - 0.030% chloride and
around 1.5% sulphate.
Normally, the alkalis vi11 be bound up ulth the chloride and
sulphate and the levels that can be tolerated in the material leaving
the fourth stage till be dictated by these components. If alkali is
predominantly present as alkali carbonate, however, we vould expect to
be able to tolerate up to at least 3% alkalis in material leaving
stage 4. Thus in terms of kiln operation it may be possible to
- 11 -
tolerate a total alkali iIIQUt to the SysteZI expressed as a percentage
of the clinker output of 1.2% equivalent xa20 without running into any
serious problems.
'3.2 Cement Quality
In terms of cement quality the obvious factor which may dictate
limiting the quantity of alkalis retained in the,clinkar vi11 be the
necessity to manufacture a low alkali cement in order to avoid expan-
sive alkali aggregate reactions occurring in the concrete. In this
respect the ASTM limit of'O.6% equivalent Xa20 is generally recognised
worldtide. Aowever, even if the productioa of a low alkali cement is
not required, it may still be necessary to limit the level of al!calis
retained in the clinker. For example alkali sulphates vi11 shorten
setting times, enhance the early strength of the cement at the expense
of its late strength, and will render the cement more prone to air
setting during etorage. These effects vi11 normally become 'noticeable
-Jhen around 1% alkali sulphate is present in the clinker and will be
significant at the 2% level.
If there is an excess of alkalis over sulphate then the alkalis
will enter into solid solution in the main clinker phases and in
general late strength will be depressed. In this situation If the
clinker is also subjected to reducing conditions then the resultant
cement will be prone to adsorbing moisture from the atmosphere and its
flowability properties uill noticeably deteriorate. This effect is
illustrated in Figure 4.
- 12 -
If there is an excess of sulphate over alkalis then the formation
of calcium langbeinite (2CaSQ.K2S04) will enhance strengths at all
ages.
If high levels of sulphate are retained in the clinker this till
limit the level of gypsum addition that can be made at the c&en&
mill. This in turn will lead to an increase in the milling energy
required to grind to a given surface area or cement strength.
Although chloride is not usually retained in the clinker in
appreciable quantities, there is always a risk where the chloride
input is high that unstable kiln operating conditions will lead to
periods of production where high levels are retained in the clinker.
This could present problems if reinforced and/or prestressed concrete
is prepared from this cement since the chloride may migrate through
the concrete and lead to corrosion of the reinforcement.
Iu the U.K. it is recommended that prestressed concrete contains
less than 0.06% chloride when expressed as a percentage of the cement
component. In practice, after allowing for the contribution from the
aggregates and water, this means limiting the amount of chloride in
the cement to less than 0.03%.
3.3. hyuass Design
Should a kiln bypass be required to control the quantities of
volatiles recirculating in the kiln or retained in the clinker, then
this Is nornally located at the kiln inlet. The objective is to bleed
off the kiln gases containing volatiles without removing excessive
quantities of dust.
- 13 -
Some plant suppliers have found the best location for such a take
off is from the riser immediately above the kiln and along the line of
its axis. Houever, promising results have also been obtaihed with
bypasses located on the side of the riser and fitted with a deflector
which keeps the hot gases from the kiln apart from the incoming feed.
The hot gases bled from the system ulll, of course, need to be
quenched to freeze the volatilised material, and then cooled and
filtered. As close to the take-off point as possible, the..gas should
either be quenched tith cold air to a temperature of 250°C and
dedusted in a glass bag filter, or air quenched to around 4OO"C, water
cooled to 150°C in a conditioning tower and dedusted in an electrosta-
tic precipitator. Variable speed fans are preferred for the quench
air and filter fans to give a reduced electrical power consumptioa
should it be found possible to operate at less than the design bypass
percentage. Tfius the capital kost of the bypass and its ancillary
equipment, whilst only a small proportion of the total cost of the
plant, is nevertheless significant.
In sizing the bypass, the procedure we have adopted is to
construct a similar volatile recirculating load to that illustrated in
Figure 1 but with a proportion of the volatiles now bled from the
system. This is illustrated for the suspension preheater and pre-
calciner process in Figures 5 and 6 .respectlvely. For these calcula-
tions it is assumed that the bypass is 100% efficient i.e. a 50%
bypass vill bleed off 50% of all of the volatiles approaching it in
the gas stream. By running our computer programme for different
- 14 -
bypass levels it is then possible to plot the stage 4 and- clinker
volatile contents against X bypass and from these plots read off the
level of. bleed required.
3.4 Bypass Operation
In addition to the capital cost, a bypass facility vi11 also
incur running and maintenance coats. As mentioned previously there
vi11 be a fuel penalty and this is illustrated for both the suspension
preheater akd the precalciner processes in Figure 7. Bypass dust will
need to be handled and disposed of and inevitably there vi11 be a
depletion of rav material reserves.
At this stage, therefore, it is uorth considering some of the
alternative eolutions. In terms of kiln operation a slight excess of
volatiles above the limits discussed in section 3.1 can often be dealt
with by installing poking facilities to remove hard deposits in the
riser pipe and in the lower stages of the preheater. -An imbalance
between sulphate and alkalis can be restored by the deliberate addi-
tion of an appropriate source of volatile compound to the feed. Uh
chloride inputs can often be avoided, for example, by purchasing a
special lov chloride coal which although generally more expensive than
the normal fuel employed we have found that in some cases its use is
cheaper overall than operating a bypass.
In tens of cement quality modifications to the setting and
strength characteristics of the cement caused by the presence of
alkali compounds can be countered by adjusting the main chemical para-
meters. ?or example it say be possible to offset the effects of
alkali sulphate by raising the silica ratio.
- 15 -
4.
If a Works is only required to manufacture low alkali cement for
some of the time then It is conceivable that alternative raw materials
sufficiently low in alkalis could be acquired for this purpose or it
may be more economic to use selective quarrying. For example, Blue
Circle Industries are presently converting an old Lepol process plant
to a precalciner. The level of sulphur in the kiln feed uas such as
to require a sulphur bypass in the updated process. Aowever, detailed
geological investigation showed that a large proportion of the sulphur
was contained vithin a well defined, approximately lm thick, band in
the shale quarry. In terms of both capital and operating cost it was
shown that it would be-more economic to discard this high sulphur
material by selective quarrying: therefore, no bypass has been
installed.
In some instances rather than operating a bypass to remove vola-
tiles it may be more convenient to make further additions to the feed
in order to produce a fully mineralised clinker with enhanced cement
propertiee. This is a technology which ue have developed and suc-
cessfully applied in Blue Circle Industries (15-17).
PRACTICAL EWERIENCE
4.1 Suspension Preheater Plants without Bypass Facilities
Blue Circle Industries currently operate a number of suspension
preheater plants without bypass facilities. Samples of kiln feed,
fuel and clinker are regularly analysed on the Works and on several
occasions samples have been taken from the stages of the preheaters ia
order to construct a volatile balance. For the purposes of this paper
-de have selected four plants to illustrate the range of our
experience.
- 16 -
The total volatile input at these plants derived from both the
raw materials and fuels and expressed on a clinker basis is as
follows:-
Plant lA 1B 2 3 4A 4B
Fuel Oil coal coal coal Gas Oil
Total S as SO3 ,0.90 0.95 1.70 0.45 0.1s 1.05
K20 1.30 1.30 0.65 0.35 0.60 0.60
NaZO 0.20 0.15 0.20 0.10 0.50 0.50
Cl 0.02 0,ozs 0.02 0.04 0.00s 0.00s
Further details of these plants, the typical levels of volatiles
found in the stage 4 feed and the typical equivalent ??a20 content of
the clinker are shown in Figure 8.
Plant 1 was originally oil fired but in 1981 it was converted to
coal firing. By necessity a low chloride coal is used 1:; order to
avoid having to install and operate a chloride bypass. With both
fuels the alkali and sulphate input is high but more or less in
balance uith the result that although build ups do form in the riser
and fourth stage they are relatively easy to remove.
The resultant clinker, however, has a high equivalent Na20 cou-
tent, the bulk of which is present as alkali sulphate. Although the
productioo of a low alkali cement is aot necessary to counter the
adverse effect the alkali sulphates have on the late strength of the
cement the Works have traditionally incorporated some sand in their
mix to lover the total alkali input and raise the silica ratio. Hore
recently, mineralisers have been successfully used at this Works to
- 17 -
achieve both a further Improvement in late strengths and a reduction
in the level of alkali retained in the clinker.
Plant 2 is also fired uith a specially purchased low chloride
coal in order to avoid a high chloride recirculating load.
The raw materials "are relatively low in alkalis with the result
that a low alkali clinket,uith an equivalent Na20 of less than 0.60%
can be easily produced. Unfortunately, these rau materials also con-
tain fluorine and appreciable quantities of sulphur and uhile both
these components can be limited by selective quarrylng their presence
leads to the formatioa of hard back end deposits uhich require regular
removal. !4'hile such removals do create a certain amount of kiln
instability this is not excessive. Overall this plant demonstrates
that vith comprehensive cleaning facilities high volatile recir
culating loads can be tolerated, and the formation of hard back end
deposits can be successfully controlled, vlthout having to resort to
the operation of a kiln bypass.
A further consequence of the presence of fluorine, hovever, is
that the early activity of the oement is depressed with the result
that, in viatet in particular, setting times are extended and any
placed concrete has a tendency to "bleed". Various solutions to this
problem have been tried but have either been impractical or unecono-
mic. More recently, however, this problem has been overcome by the
use of mineralisers.
Plant 3 is fired ulth a locally available coal. As a consequence
it3 chloride Input is high and would normally require the operation of
- 18 -
a small chloride bypass. Houever, the sulphate and alkali inputs are
both relatively low, and more or less in balance, vith the result that
by operating facilities to regularly clear away deposit? which form in
the riser and stage 4 the need to bleed any of the kilns' gases has
been avoided. The resultant cement has a very low alkali coatent well
belov 0.60% equivalent Xa20.
Plant 4 contains bath an oil fired kiln and a gas fired kiln.
30th kilns have a lov chloride input but a high alkali input which
results in the equivalent Xa20 in the clinker exceeding 0.60%.
However, as extended cements are mainly produced at this Works this
does not present any problem. . In term of kiln operation, the gas
fired kiln has an excess of alkalis over sulphate uhile the oil fired
kiln has an excess of sulphate over alkalis. Both kilns form deposits
in the riser and fourth stage which are easily removed.
Construction of the volatile recirculating load for each of the
above 'kilns has indicated that the proportion of volatiles evaporated
in the burning zone of each is similar. In all cases (Figure 9) vlr
tually all the chloride, approximately 85% of any excess sulphate over
alkalis, around 65% of alkali sdphate and about 60% of excess alkalis
over sulphate was evaporated.
4.2 Chloride Bypass - Plant 5
In addltioo to the above suspension preheater processes, a
further one is operated in the Blue Circle group *with a small bypass
to remove chloride. Up to 1975 this plant uas oil fired, thereafter
it has been fired with natural gas.
- 19 -
The raw materials employed on this 53orks comprise a high grade
limestone, a marl and a sand. Both the limestone and marl contain
chloride with the result that the total chloride input to the kiln
system, as a percentage of the clinker output, is around 0.10 - 0.15%.
In designing the bypass for this plant it uas assumed that both reten-
tion of chloride in the clinker and loss up the stack uould be negli-
gible. As a consequence it was predicted (Figure 10) that a kiln
bypass of some 8 - 10% would be required to lower the concentration of
chloride in the stage 4 feed to an acceptable level. In practice,
however, up to 0.01% chloride can be retained in the clinker vhile a
somewhat smaller amount leaks up the stack uith the result that the
actual bypass operated is in the range 6-8X.
Volatile and mass balances have been constructed for this plant
with both fuels. These have indicated that:-
i> the proportions of volatlles evaporated in the buhling zoue are
similar to the other suspension preheater plants operated in the
Blue Circle Group
ii) the bypass is also effective at bleeding sulphur and al!calis from
the system
iii) changing from oil to natural gas did not affect the performance
of the bypass although some change in clinker chemistry and
cement quality and grindability as a result of the lover sulphur
input was noted.
4.3 Alkali Sypass - Plant 6
This is a 2500 tonnes per day oil fired precalciner process uhich
- 20 -
came on stream in December 1981. The tav materials consist of a high
grade limestone, a siliceous limestone, a clay and iron oxide. The
total volatile input, as expressed as a percentage of the clinker out-
put, i s : -
%
Total S as SO3
K20
Nat0
Cl
0.75
0.75
.0.3s
0.01
Use of these raw materials produces a mix with a relatively high
silica ratio of around 3.5 and a difficult combinability.
Consequently it was assumed when designing this plant in the late
1970's that the degree of evaporatioo which would be achieved in the
burning zone uould be at least the same as that found in our suspen-
siou preheater processes.
Against this background and assuming losses up the stack would be
negligible it was predicted that the bypass required to produce a lov
alkali cement would be 30% (Figure 11). At the time all the main
plant suppliers agreed with thi's prediction.
However, since the plant has been in operation difficulties have
been encountered in producing a low al'kali cement. Close monitoring
of the process, during a series of trials carried out In conjunction
with the plant supplier, has established that while the bypass is
currently limited to only about 25% the main reason for this failure
- 21 -
to produce a low al'kali ceaent is that the degree of evaporation
a'chleved in the burning tone is lower than *was expected. Further
investigation has indicated that the main reason for this is the very
much higher solid to gas ratio achieved ia. a precalciner'kiln which
restricts the sueeping action of the gase&*).
On this basis (Figure 11) it is estimated that the bypass would
have to be increased to around 60% in order to produce a suitably low
al!=11 clinker.
.AI.temative solutfoas have been considered.. Attempts to increase
the volatility in the burning zone by raising the lime saturation and
silica ratio of the feed, or by burning more fuel in the rotary kiln
rather than in the precalciner were only partially successful. Adding
chloride to the system to enhance the volatility of the alkalis or
selective quarrying of the raw materials to lower the alkali input
have been considered but are expensive. At present the Works
have found the least expensive solution is to
low alkali clay and produce low al'kali cement
pending modification to the bypass.
4.4 Sulphur Bypass - Plant 7
This is a 1200 tonnes per day coal fired precalciner process
buy In an alternative
on a campaign basis
which was first lit up in September 1982. The raw materials consist
of a high grade and a low grade limestone. Both these and the fuel
employed contain appreciable quantities of sulphur *with the result
that there Is a gross excess of total sulphate over al:kalis entering
- 22 -
the system. The total volatile input, as expressed as a percentage of
clinker output is:-
Total S as SO3
K2O
Na20
Cl
I
2.30
1.05
0.65
0.01
These raw materials produce a mix uith a relatively lou silica
ratio and an easy combinability and it was anticipated that volatility
in the burning zone could be low. In addition, from the form of the
sulphur in the rau materials it vas recognised during the design stage
that this might be volatillsed in the upper stages of the preheater
and escape up the stack, Comercial decfsioas dictated that the plant
had to be ordered before the rav materials could be comprehensively
tested and consequently when sizing the bypass we decided to take the
possible conservative view that only a limited quantity of SO2 may
escape up the stack and that the volatility of the excess sulphate
over alkalis entering the burning zone as calcium sulphate could well
be dissociated to the same degree in a precalciner process as in the
suspension preheater process. Accordingly, ue estimated (Figure 12)
that the bypass would have to be at least 30X and that cleaning faci-
lities similar to those employed at our plant 2 may also be required.
At the same time our calculations showed that while the clinker
sulphate content would be sufficiently lowered (Figure 13) to pemit
an acceptable gypsum addition, the allcall content of the clinker
- 23 -
(Figure 14) uould remain high. Fortunately, the production of a low
al'kali cement is not required at this Works'and, although the alkalis
are mainly present as alkali sulphatcs, their effect on the cement
strength is also not critical (indeed it is beneficial) as the
majority of the cement produced at this Works is extended with an
addition of natural pozzolan. However, the presence of alkali sulpha-
tes uas expected to lead to air setting problems necessitating
appropriate counter measures.
In general the plant supplier agreed ulth these conclusions.
Their calculations shoved that while a lover bypass would probably
suffice, a 25% bypass should be installed to cater for all even-
tualities and therefore they raised no objection to our proposal to
install a 30% bypass.
Ho-vet, uhen the plant was fully commissioned in November 1982
it became clear that the Win could be successfully operated wlthout
having to bleed any of the kiln's gases. Since at that time the fuel
cousumption guaranteed by the plant supplier still needed to be
checked opportunity was taken while performing this exe&se to take a
range of balance samples at different bypass settings. The results of
this investigation are shovn by the dotted lines on Figures 12-140
The main points to emerge from this evaluation were:-
i> around 50% of the total sulphide present in the rav materials MS
evaporated in the upper stages of the preheater and escaped up
the stack
- 24 -
ii) the proportions of volatiles evaporated in the burning zone were
substantially lower than in any of our other plants.
As a consequence, acceptable lev.$ls of total sulphate in both the
stage 4 material and the clinker are obtained without having to resort
to bleeding any of the kiln's gases* Hovever, the level of alkali
sulphates in the clinker Is high and as expected the Works have been
forced to counter airsetting problems.
Follouing these observations we have developed a laboratory test
method for assessing the potential for sulphur to burn off over the
temperature range likely to be encountered in the upper stages of a
preheater. 'By subjecting raw materials to this test irom a number of
sites ue have shown that this cannot be readily predicted from the
chemistry alone but is dependent on a number of factors including the
form the sulphur occurs in the raw naterials, the temperature at which
the calcareous component in the feed starts decarbonating and the
atmosphere in the preheater, which may itself be influenced by the
composition of the feed.
DISCUSSION XND CONCLUSIONS
1. In modern, high thermal efficiency dry process kiln systems, con-
tinuity of kiln operatioa and clinker cement quality are more
susceptible to adverse effects of volatile components in the kiln
feed and fuel. Wet, long dry and Lepol or ACL process plants are
not so sensitive.
2. In some circumstances it has been found that such effects can be
more economically countered by selective quarrying, or by the use
- 25 -
of alternative raw materials or fuel, or by adjusting or minera-
Using the chemistry of the clinker, or by adopting intensive and
automated techniques for clearing build ups from the riser pipe,
rather than by resorting to a bypass.
3. The adoption of precalciner processes has made it practicable to
employ bypasses of up to 100% of the rotary kiln exhaust gas,
compared tith a practicable limit of about 25% vith a simple
suspension preheater system.
4. However, with a precalciner process only about 40% of the fuel
is burned in the rotary kiln itself and recent experience shovs
that the volatilisation of alkalis and sulphates in the kiln are
lower than in normal preheater kilns. This reduces the effec-
tiveness of the bypass where the objective is to limit the al'kali
or the sulphate content of the, clinkers.
5. While siting a bypass to remove chloride is relatively easy, that
required to remove alkalis and sulphur Is more complicated and is
dependent on the interaction of these compounds and their volati-
lity in both the preheater and the rotary kiln and is therefore
more difficult to size.
6. -Although plant data provides a number of useful reference points
from which future predictions can be based, there is also a need
for the properties of the raw materials and fuel to be e!UplOyed
to be thoroughly evaluated in the laboratory.
- 26 -
For our part in Blue Circle we have both a comprehensive modern
laboratory which can carry out such investigations and coaslderable
background experience and data from the operatioa of plants.
6. ACKXOWLEDGEHENTS
The authors wish to thank Blue Circle Industries PLC for their
permission to publish this paper and to colleagues and Associate corn-
panics vithin the Blue Circle Group for their contributions.
7. REFERENCES
1. Reactions associated vith the kiln gases: Volatile cycles, build-
ups, ring removal.
F.W. Lecher, S. Spmng C D. Opitz.
Zement-Kalk-Gips, 1972, 25, (l), l-12.
2. Bypass systems for preheater and flash calciner kilns-
N.U. Biege h L.J, Parsons . '
Pit and Quarry, 1978, 2 (L), 91-97.
3. Second generation precalclnlng with bypass alternatives for
alkali control.
F.I. Kohanowski h J.L. Shy.
Proceedings of the 13th International Cement Seminar,
Chicago, 1977, 98-108.
4 . Eeductioo of alkali and sulfur content of clinker by kiln bypass
in flash calciner systei.
J. Tjarshawsky & E.S. Porter
In Process technology of cement sanufacturing,-
VDZ Kongress L977, 652-659.
- 27 -
5. New cement plant in Abu-Dhabi uith precalciner 'kiln process with
100% kiln gas bypass system.
N. Xakamura & 2. Tojo.
Clments, BiGtons, Platres, Cbaux, 1982, (7381, 268-274.
6. Redustioo of alkali and chlor%e cycles in the suspensioa pre-
heater kiln.
3. Schliiter
Zement-Kalk-Gips, 1972, 25, (l), 20-22
7. Raw meal preheater and alkali problans.
B. RItzmann.
Proceedings of the Eighth International Cement Industry Seminar,
Chicago, 1972, 39-47.
a. Cyclic behaviour of volatile components in dry process plants for
burning cement clinker.
W. Danowski h U. Strobel.
Silikattechnik, 1977, 28, (2), 40-43.
9. Hethod for predicting cyclic behaviour of deterious substances in
cement 'kilns.
W. Kreft.
Zement-Kalk-Gips, 1982, 35, (9), 456-459.
10. The behaviour of sulphur in cement clinker burning.
S. Sprung.
Tonindustrle-Zeitung, 1965, 89, (5/6), 124-130.
- 23 -
11. The behaviour of sulphur in the suspension preheater kiln.
H. Eatano.
Zement-Kallc-Cips, 1972, 2, (l), 18-19.
12. Investigatioos of the formation of rings in rotary cement kilns.
3.93. Sylla,
Zement-Kalk-Gips, 1974, 27, (LO), 499-508.
13. Xing Formation in Rotary Cement Kilns.
D. Opitz.
Schriftenreche der Zementundustrie No. 41, 1974.
14. The distribution of al'kalts in Portland cenent clinker.
H.W.U. ?ollitt h A.W. Broun.
Proceedings of the Fifth Internatioaal Symposium on the Chemistry
of Cement, Tokyo, 1968, Vol.1, Part I, 322-333.
15. U.K. Patent No. 1498057.
16. Use of mineralisers to produce high strength cement.
G.R. Long.
Proceedings of the Fifth International Conference on cement
rnicroscapy. Nashville, 1983, 86-98.
17. Improvements in the early properties of Portland cement.
G.K. Yoir.
Proceedings of the Royal Society discussion meeting,
London, 1983, 127-138.
- 29 -
3.8. Processing of 'kiln dust
B. Tettmar, S.R. Khor and S. Gregory
Process Technology of Cement Manufacture
WZ Koogress 1977, 658-663.
FIG 2. Calcium Langbeinite (arrowed blue) with associated alkalisulphate (arroued red) in production clinker.
FT.G 3. Laths of calcium sulphosilicate (arrowed yellow) within densecal clum sulphate rich deposit from sintering zone in kiln.
FIG 4. Dark chain like droplets (arroued white) of atmosphericmoisture occurring on the surface of a polished section of a clinkermanufactured in a reducing environment.
.Ti-
cW
,*iu
-b .
-
!-,y
4T.i =i
‘t!I G!-a
.3
‘1, cr,
+L ‘2
z:..:
iyL
LiL
I-
!Z-
1
:i27.;
&I.
ax.-
L‘I-‘z-
.-
:ri&
.--....... . . . . . . . . .
,_
i--.-l.-.:, ..!.
II-- f.,,.... . . .._I
~ _ .. ..LIl-l-
ail.._
..... . . . . . . . . . .._.__..
- c
Figure 7-f&l Consumption vs % BypassI_-
11001100
7373ss--33* 1000iii2g.I
P51 g00
8-43A.23.g 8 0 0
%cdi-L
/
/
/ ;//Suspens ion
000 Precalciner KilnAir separate)
High Dust Loss - - - -Low Dust Loss
10 20 30 4 0 50 60 70 8 0 90 100% Bypass
00
00
00
LnLnO
u3LnLo
a3
a3
cn
m-c
n4
- 4
Figure $-Typical Kiln Volatilities of E3CI Suspension Preheater Process (No Bypass)- - -.. - -
100
90
80
7 0n
20
10
0
Chloride
AlkaliSMphate A
6s 3,
Llr
‘lkali S(other than Alkali Sulphate
Sulphate(other than Alkali Sulphate)
QS-
(u
kI
co .
Fiqure IO-Chloride Level 4 Stage 4 vs % Bypass in PLd 5
11
1 0
9
8
7
6
5
4
3
2
1
Predicted Level
- A - - - Actual Level
4 6 0 1 0 12‘10 E&pass
ommendeBypass
Figurell, -E%quivaleht NazO in Clinker (Ye) vs ‘lo Bypass in Plant 6.
Predicted levels for suspensionprahealer kiln volati(ities---I- Revised prediction using Bypass trial data
Actual levels from Bypass trial
mendat ion
40 50 .60z!!LBBy~
80
Predicted lev& for different kiln volatibtiesw - - L --- Actual iwels from Bypass trial
&commended
1 I I 1 I , , 1 1 1 J
0 5 1 0 15 20 25 30 35 40 45 50 55‘lo Bypass- -
FJgure14--E4uivaient NgzO in Clinker(%) vs % Bypass in Plant 7
2.0 -
1.8 -
I.6 -
f-#+zdicted IQVQ~ for different kiln volatilitibs_c-m-- “Actual IQVQIS. from Bypass trial.
0.6 -
o-4 -
ecommended Bypass
o-2 -
0’ I I I I I 1 I 1 I 1 10 5 10 15 20 25 3 0 35 40 45 5 0 55
B y p a s s‘lo
III1I
:- ’
I. _-
’ L. .
.Fi
In
,C
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 8
Kiln Gas Bleed Considerations
KILN GAS SLEED CONSIDERATION!fj
2 .
The process under consideration wiil need a chloride bleed in order thatregular kiln operation can be maintained. With the present raw materials,the required bleed level will be 30 to 50% of kiln gases. At this bleedlevel, clinker equivalent soda levels will be very high, at 0.9 to 0.95%, butcould be reduced by 0.1% by use of a bleed of up to 75%.
Other options for clinker alkali reduction are the use of alternative rawmaterials, which is also likely to reduce the bleed requirement for kilnoperation, or addition of CaCl, which will have a major effect on alkalilevel but will require a larger gas bleed.
Dust loss with the bleed is likely to be 200 to 250 gnns/Nm’ of gasextracted from the system but design should assume a level of 400grms/Nma.
INTRODUJCTION
Since the development of the suspension preheater based dry process forcement manufacture, the study of the inherent cycling effects of thepotentially volatile components - which are present as minor constituentsof the raw materials and fuels - have become increasingly Important. Inthe older, less thermally efficient processeS, a natural loss of a portionof these volatile components occurred in the waste gases, soautomatically controlling the recirculation levels within the burningsystem and the level in the clinker product.
In the suspension preheater, with its greatly increased surface contactbetween gas and particle and repeated separation of gas and particle, therecovery and retention of volatilised components will be almost complete.This leads to Increased proportions of these components in clinker andwithin the kiln system; which can lead to the development of operationalproblems in the pyre-processing stage due to the quantities of potentiallysticky components that build-up through cyclic processes. Wherenecessary, a portion of the kiln gas is bled off in order to remove aportion of the volatile components and so control the levels of thesecomponents either in clinker because of cement quality requirements orin the kiln system because of the potential to cause blockages within thepreheater.
The minor components that are generally considered to be involved inmajor volatile cycles are the fluoride, chloride, alkali and sulphur species- although other elements do also become involved in cycles to a muchlesser degree (V, As, Pb, TL, Cd, Hg, Zn), these are not important for thisstudy.
1
Prime control of the volatile component cycles is performed in the designstage of a works project through the selection of raw materials and fuelsin order to optlmfse the relative and absolute levels of the potentiallyvolatile components and, where necessary, the inclusion of a bleedsystem. Once these factors have been defined, the voiatiles will developinternal and external cycles during the pyre-processing stages; an internalcycle being totally within the kiln and preheater system, whilst anexternal cycle will leave the system but be returned after a time lag (forinstance with the precipitator dust). Where processing conditions are keptsteady, the cycles will continue to develop until equilibria are reached, atwhich time the total amounts of volatile entering the system will bebalanced by the quantities leaving the system.
The degree of volatilisation and the ratez at which the equilibrium areestablished will depend on:
(a)
b)
(cl
(4
(e)
(0
kc)
(h)
(i)
(j)
The species, their chemical forms and concentrations.
The volume of gases.
The intimacy of contact between gas and solid.
The vapour pressures of the salts.
Possibility of dissociation or further reaction.
Rate of diffusion to and from solid/gas interfaces.
Degree of saturation of gas.
Kiln atmosphere.
Kiln temperatures.
Time/temperature profile of material within the kiln.
Most of these Factors are to some degree inter-related and so in normaloperation the only methods available to control the degree ofvolatilisation and eventual concentration in clinker and kiln system willbe the kiln internal atmosphere and temperature, and the proportion ofgas bleed from the kiln exit.
The major cycles will be internal cycles between the burning zone andpreheater where an individual cycle time of twenty to thirty minuteswould be expected. Smaller quantities of volatile components may beinvolved in the longer term external cycle which develops via theprecipitator dusts and volatile colIection in the raw mill.. These would beexpected to have much longer cycle times of up to 24 hours.
Any kiln gas bleed from a suspension preheater system obviously has a
2
3 .
3.1
3.2 Fluorides
fuel penalty associated with it. For a standard preheater, it is generallyconsidered that a 30% bleed approximately represents the maximumeconomically justifiable level, whilst in a precalciner the equivalent kilnexit gas volume can be between 30 and 45% of that of a simple suspensionpreheater which makes bleeds of up to 100% justifiable under certaincircumstances. Because of this factor, control of the cycles for improvedprocess operation is easier on a precalciner than on a suspensionpreheater. Conversely control of the proportions of the volatiles inclinker is more difficult due to the reduced volatilisation that occurs inprecalciner kilns - a consequence of factors (b) (c) (f) (i) and (j).
GENERAL FUZVIEW OF PROPERTIES OF VOLATILE COMKNENTS
General Comments
In practice, the proportion of each potentially volatile compound whichevaporates within the kiln can vary significantly depending on the speciesand the type of process. Typical ranges that have been reported in theliterature are set out in Table 1, whilst Table 2 details melting and boilingpoint data for the major components. In the past, empirical limits havebeen proposed for the total concentrations of volatile input to a kilnsystem but modern practice is to specify the concentrations that can be
- tolerated in the lower stages of a preheater. The maximum reportedranges that are generally accepted at this point as being unlikely to causeany operating problems are:
chloride 1.0 to 1.5%so, - 2.5 to 4.5%alkalies 2.5 to 3.5%
It is possible to operate successfully with significantly higher levels ofindividual components, however, the overall effect on kiln operation woulddepend on the relative proportions of individual compounds and the effortput to cleaning the preheater interior. The individual components arediscussed in the following sub-sections.
Fluorides can be found naturally in raw materials or be deliberately addedin small quantities to the raw mix. In low proportions its mineralisingaction has a beneficial effect on the burning process. Generally, it haslow volatility and causeS few operational problems, although a level ofabove 0.25% in clinker may lead to setting problems, particularly inwinter. Cases have been cited, however, where a hard dense build-up hasdeveloped in preheaters where the build-up contains a high (over 1%)proportion of fluoride.
3.3 Chlorldq
Chlorides are derived from the raw materials and the kiln fuel. The highvolatilities of these compounds, together with the high collectionefficiency of the cyclone preheater systems, will lead to the developmentof a greatly enhanced cycle. The chlorides have a high affinity for thealkalies in general and potassium in particular. This property, togetherwith the high volatility, has been used in kilns (commonly on the wetprocess, occasionally on the SP process) to control clinker K,O levels byaddition of CaCl, to the raw mix or fuel, which leads to loss of KC1 withthe kiln bleed or the exhaust gas from the kiln system. In the suspensfonpreheater, the volatilised material is recaptured within the system unlessa bleed is utilised between the kiln and riser duct. It is generallyconsidered that no more than 3% of the chloride passing from thepreheater to the kiln will leave the system with the clinker. Al*thoughconsiderably higher levels have been noted in individual samples ofclinker, this is probably due to a ‘push’ of kiln feed, or a semi-flushsituation as thermodynamic considerations indicate that no chlorideshouldpass through the burning zone. On many SP kiln systems some degree ofpreheater cleaning is necessary on a regular basis and this may help tocontrol the chloride cycle by forcing the kiln conditions into a situationwhich permits a brief increase in clinker chloride level (i.e. reducedmaterial temperature, increased material loading and flux level).
Small amounts of chlorides will also leave the preheater system with thewaste gas stream. Taking the total loss of chloride from the system asbetween 2 and 5% of the feed to the burning zone, it would then beexpected that a circulating load of 20 to 50 times the total chloride inputcould develop in a system without a kiln gas bleed.
No reports of low temperature chloride volatilisation within the preheaterhave been identified.
3.4 Alkalies
The major source of alkalies will be the raw mix; notably the claycomponent, although minor quantities can arise from the fuels. Theinitial free alkalies will behave in one of three ways:
(1) Remain in the material being processed and become incorporatedin the clinker constituents that are being formed. This happens toNa,O to a greater degree than K,O.
(2) Be converted into different compounds - chlorides, sulphates,carbonates, hydroxides - by reaction with other constituents of theraw mix.
(3) Diffuse to the surface of the process material and volatilise.
4
3.5
In its initial state, K,O begins to volatilise over a wide range oftemperature, depending on the form of clay In which It was incorporatedbut irrespective of source, it would be expected to have volatilised almostcompletely at burning zone temperatures, although some may have beenat least partially stabilised by conversion to the less volatile sulphateform within the material bed. Once volatilised it will react to formchlorides and suiphates - chlorides preferentially - at the rear of the kiln.These will then deposit on dust particles. Initially Na,O is less volatilethan K,O due to its higher bond energy and so a greater proportion of thekiln feed Na,O would be expected to pass through the burning zone inclinker without participating in the volatile cycles. Volatflised Na,O willreact with SO, and SO, to form sulphates towards the rear of the kiln andwith chloride where this species is present in excess of K,O. Where alkaliis present in excess of chloride and sulphate, alkali carbonates will beformed. Each of these alkali compounds will deposit in a liquid state onthe surface of dust particles in the cooler zone of the kiln and lowerpreheater stages and will enter the volatile cycles as the dust is separatedout in the cyclones. Direct contact onto kiln or preheater surfaces maylead to the development of build-up. The compounds will then re-enterthe kiln where the degree of volatllfsation will depend on the species andthe kiln conditions. Volatility decreases from chloride to carbonate tosulphate and, hence, sulphates are more likely to pass through the burningzone. Nevertheless, the likely range of burning zone temperatures coverthe thermal area in which alkali voiatilities are likely to increasesignificantly with rising temperature. In general, precalciner kilns havesignificantly lower burning zone temperature than are common in otherprocesses and, hence, alkali sulphate volatilisation in particular is lowerin precalciners than in other processes.
SulDhur
Sulphur can enter the system in a number of forms from either fuels orraw materials. A limited amount may evaporate in the upper preheaterstages and escape from the system in the exhaust gases. In general, SO1and SO, can form in the high temperature areas and be transferred to thegas phase. In the cooler areas of the kiln back-end and preheater system,sulphates will form and re-enter the material stream. Preferentiallyalkali sulphates will be produced with excess sulphate combining with freelime or calcium carbonate and hydroxide that Is available in these areas.Where reducing conditions exist, the equilibrium will favour the existenceof SO, and SO,, so restricting the formation of sulphates. In thissituation loss of suiphur oxides by way of the stack may increase butwhere the gas stream passes through the raw mill, the mafority of thesulphur oxides would be expected to react with the high active surfacecalcium compounds which are produced in the milling process. This willthen return to the kiln in the raw mix as part of an external cycle.
The high boIIing points of the alkali sulphates would Indicate thatrelatively low levels of volatilisation would be expected. However,dissocfation may occur, particularly under the reducing conditions which
5
can exist to some degree within the burning zone. Calcium sulphate alsohas a high boiling point but is even more susceptible to dissociation, so ahigher recirculation of sulphate from this compound would be expected.As CaSO, cannot recycle as a compound, the lime from this compoundremains in clinker as free lime - making burning more difficult - whilstSOS is carried in the gas stream to the kiln back-end where it reacts toform alkali or calcium sulphate.
4. BLEED REOUIREMENT
The proposed new line is based on a precalciner process. The raw mixcontains such high levels of chloride and alkali that the system would beinoperable without a kiln gas bleed. In addition, the alkali level in theclinker could potentially restrict the markets open to this material.
A series of raw mix designs have been considered and associated with thiswas a series of calculated material analyses based on the i3CIvolatilisation model, showing the effect of gas bleed levels between zeroto 100%. The results of these calculations are presented agafn in Table3. ,Mixes 6 and 8 represent the proposed range of clinker chemistry andfrom the material analyses these would have a chloride content in the rawmeal of approximately 0.22%. Figure 1 plots the effect of kiln gas bypasson the chloride level in the material passing from preheater to kiln andindicates that a bypass requirement of 33% is anticipated in order torestrict the chloride level at this point to 1%. Figure 2 indicates theeffect of increased chloride content in the raw meal, with chloride levelsof 0.25% and 0.30% requiring 38% and 48% bypasses respectively. Thelevels of chloride bleed would also control the levels of alkali and sulphatein the kiln inlet material to acceptable levels for kiln operation. With thelevel of bleed necessary for the control of chloride in order to maintainsatisfactory process operation and with the proposed raw mix, alkalilevels in clinker are likely to be about 0.95% Na, equivalent, as indicatedin Figure 3.
Such an alkali level is likely to be acceptable in many areas but may notbe acceptable in parts of the world where ASR is a significantconsideration. Lower clinker alkali levels can be achieved in one of threeways:
(1) Increased bypass level. Increasing the bypass level to 75% wouldbe expected to reduced the clinker equivalent soda level tobetween 0.8 and 0.85% depending on the mfx (Figure 3). In thiscase the majority of the reduction would be in the K,Oconcentration due to its higher volatility.
(2) Use of alternative raw materials. The use of an alternative rawmaterial to clay could significantly reduce the input of alkalies andchloride to the process. As an example, mix 11 in Table 3considers the effect of using 2% of a European bauxite in the mix.
6
This would reduce the cIay usage by about WY% and increase thesandstone requirement but the overall effect on the volatilecomponents is to reduce the concentrations by between 25 and40%. The immediate result of this is to reduce the kiln gas bleedrequirement for chloride control from 33% to 22%. At this lowerbleed level a clinker equivalent soda level of about 0.7% would beanticipated, whilst high bleed levels would permit further reductionin a similar manner to case 1 (e.g. 50% bleed 0.6% equivalent soda- the exact effects would obviously depend on the full chemicalanalysis of the material used).
(3) Addition of CaCl when lower alkali clinker is required. This couldbe used to make a separate quality clinker as needed. The chloridewould preferentially react with alkali and thus increase thevolati$ty of this species. However, this route would require thatthe bleed system has the potential for operation at higher levels -possibly up to 100% - during such periods of manufacture.
OTHER EFFECTS OF KILN GAS BLEEDS
As the kiln gas bleed removes gas and material at high temperature, thisobviously has a significant heat penalty on the process. A first orderestimate of the fuel penalty can be obtained from Fig. 4. The dust thatis extracted from the process has a high volatile content and so cannot bere-used within the kiln system. Consequently any dust drawn out with thegas bleed will effectively increase the raw meal to clinker factor and sorequire increased capacity in all the stone processing and mealpreparation stages through to the kiln feed point. Recently the majormanufacturers have all been making significant efforts to reduce theamount of dust extracted for a given gas bleed percenta Q e. Currently,most will design for a dust loss of 150 to 250 grms/Nm of gas bleed,whilst users are commonly reporting figures of 150 to 400 gnns/Nm’ withextremes of up to 600 grms/Nm’. The effect of this range on dust lossfrom the system and consequent extra raw meal requirement for the twoproposed plant sizes is shown in Table 4. It is assumed that in normaloperation the dust loss will be approximately 200 to 250 grrns/Nma butthe design parameters for raw meal preparation should allow for up to 400grms/Nm’.
AD JL/JAS
7
TABLE 1: VOLATWY FLANGES
(a) Primary Volatilitks
%
SO, 60-90
K,O 30-70
Na,O 20-40
Cl, l-b 96-99
F IO-40
01) Specific Volatflkies
‘56
KS4 40-60
NaS4 40-60
2CaSO,.Ks, 40-100
K,O In solid 60-90solution
Nai in solid 20-40solution
i
! I
Pb, Tl SO-99 KC1 I 97-99
Cd, V, Zn
I
I O-20 NaCI 96-99
CASO, 80-100
Primary volatilities indicate reported range of volatilities irrespective offull chemical form.
Specific volatilities indicate the reported range of volatllities for themore common compounds.
TABtE 2 : MELTING 6 l3OLlNG POWI- DATAT
Melt&g Point Boiling Point D&XX&lOC Oc OC
SoDiUM
Chloride 800 1440 - 1465 over 1200
Sulphate 884
Carbonate 850 - 854 dissociates
Hydroxide 319 - 328 1390
IfOTA9XJ-M
Chloride 700 - 768 1407 - 1411 over 1200
Sulphate 1075 1689
Zarbonate 894 - 897 disszlates
bIy&oxide 320 1320
Calcium Sulphate 1297 1350
bJ.9r1113
-1.93
000.430.510.600.229
14.05
:::43.2135.05
0.090.33
cz9
96.02.41.5
14.493.342.2342.w3.73
0.130. $1
22:
93.02.6
13.943.492.X4.923.35
0.140.5.30.560.227
w.0
LO1
1
2020.510.800.330.138
0.42
0
950.550.390.910.367
0.41
m100.60
zo:a7
000.490.7a0.810.331
0.41
Y,50.470.90.630.241
0.54
co1 0
E0:67O.ZS!
0.57
5450.570.820.860.W
0.43
0.81 0.66 0.4715.16 2.4a 1.331.27 1.16 1.W11.036 1.91 0.67
m100.590.870.900.368
0.45
0.430.87
z
0.260.250.590.U0.75
000.9O.Bc0.360.34
0.39
2020.4s0.Y0.410.234
0.540.40 0.42
0.440.9O.%0.387
0.Y
3.713.43. w7.64
f-43L3lj-61L 076Lrn
O.Br6.001.341.63
::21.231.38
0-n1.670.861.034
0.33
8.:0147
0.370.570.670.29
0.491.431.100.71
22.25.123.4265.60
33.02.6_
21.39s. 353.56
21.633 . 2 3
96.02.4
1-S1.5
23.6 23.8
54198
10
6513811
%138I2
_--.
TABLE 4 : WI%CT OF DLJZED LJZVEL AND DUST LOADING
I
-7
-
c
Plant output 5500 tpd I 7500 tpd
Bleed % Dust Load Actual Dust Los Raw Meal Equivalent Actual Dust Loss Raw Men1 Iquivolentgrm/Nm3 .
Av tpd Max tpd Av tpd Max tpd Av tpd Max tpd Av W Max tpd
30 100 78.4 82.5 117.4 123.6 106.9 112.5 160.1 168.5200 156.8 165 234.8 247.2 213.8 225 320.2 337.1300 235.1 247.5 352.2 370.8 320.6 337.5 480.3 505.G400 313.5 330 469.7 494.4 427.5 450 640.4 674.2500 391.9 412.5 587.1 618 534.4 562.5 800.6 842.7600 470.3 495 704.5 741.6 641.3 675 960.7 1011.2
50 100 130.6 137.5 195.7 206 178.1 187.5 266.9 280.9200 261.3 275 391.4 412 356.3 375 533.7 561.8300 391.9 412.5 587.1 618 534.4 562.5 800.6 842.7400 522.5 550 782.8 824 712.5 750 1067.4 1123.6500 653.1 687.5 978.5 1030 890.6 937.5 1334.3 1404.5600 783.8 825 1174.2 1236 1068.8 1125 1601.1 1685.4
70 100 182.9 192.5 274 288.4 249.4 262.5 373.6 393.3200 365.8 385 547.9 576.8 498.8 525 747.2 786.5300 548.6 577.5 821.9 865.2 748.1 787.5 1120.8 1179.8400 731.5 770 1095.9 1153.6 997.5 1050 1494.4 1573500 914.4 962.5 587. I 618 1246.9 1312.5 1868 1966.3600 1097.3 1155 1643.8 1730.3 1496.3 1575 2241.6 2359.6- J
-__-_=
Three potential raw mixes were selected for the bypm calculation (on the basis ofkiln operation and quality).
(1) For the situation where a bypass was in operation, the fuel consumptionwa5 assumed to rise by PKcallKg per 1% of kiln gzs bleed from thesystem and 1% dust was assumed to be lost by 10% bypass in operation(precalciner process). The fuel consurnptions and dust losses on clinkerbasis were estimated as follows:
(2)
(3)
The estimated clinker analysis has been calculated for the situation wherea bleed of 0, 10, 20 50% and 100% of kfln gasa fs in operation.
When a bleed is In operation, the levels of volatiles leaving the system inthe clinker was calculated on the basis of the following assurnptiom
0) All the recirculating voIatiIes are potentially available to leave thesystem via a bleed.
(ii) The following volatillsation rata were assumed:
NaCl 99 ExcessK,O 35KC1 99 E x c e s sNa,O 35Kfl.4 40 Ca!Xl, 40KG04 40 tCasOq.K&04 40
The total volatile input is the sum of the volatlles from the raw feed andfrom the fuel expraed on a clinker basis.
WV
,a
arr$O
A1
.a1..0
.:.. . . .
.: ._’. .
__
’.:
cyHk
. .
. .;
._’
. .
. . . . ..
. .
. . . . ..
. .
. .
. .
. .
. .
..
.. . .
0
0to
e-4 -
to+x
04 -
d6
I /
i i i
/ ; j / i i
;ii i ii i i ; i i i
.
0co
t i
i ’
’
, ,
I ,
.I’
, I
1I
I I
I I
;I1
’i
I !
I 1
iI
1I
iI
.I’4.
! i
L:
I I
I I
II
I I
I .III
r :
, 1 :
11-i a
’t
i i
I i-i
t, !
; I:!
I ,
’ I
; 1;.
:: i
::
; *
!0-3
t i
i ‘iiiI
ii
ij
!I;
I i
II
Fig. rt. E S T I M A T E D H E A T C O N S U M P T I O N v s *lo G A S B L E E D O F FA T T H E K I L N B A C K E N D
HEAT CONSLJt.4P1ON()I cd/kg NETT)
950
925 -
r
9 0 0 - - -
875 --
r
850 .
.“__..
825
liiiclc
- .--.e ..-- .fl
/- .’
*.
8000 10 To
,�ib l /;i;.
-.. --
--_--.--
-.--DUST LOSS
64
-- ..-
-.-. --
;./
---
..--. --
/=’.-
0/’
SUSPENSION PREHEATF~~ K I L N(100% F U E L IN)ECTION INTO THE Kl
-. - P R E C A L C I N E R K I L N--._(LO’/. FUEL INJECTION INrO THE KILN]
IUST LOSS EX K ILN *I. ON CLINHtmH
I 1 I I
30 L O 50 G O 70 n o
‘1. G A S BLEED O F F A T ItIE K I L N DACK EN0
90
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 9
Ring Formations in Cement Kilns
Ring formations in cement kilnsGreg PalmerPlant Superintendant, Queensland Cement Ltd, Australia
IntroductionRing formations in cement rotary kilns have beenknown to induce operational instability and restrictgas flow to the point where production must bestopped. Rings that can cause severe operationalproblems in long wet kilns have been found in thefollowing areas:
Transition zone
Chain area
Kiln discbarge area
To prevent rings forming it is necessary to under-stand the mechanisms that assist in formation.There are a number of mechanisms, detailed byRumpfc2), that can lead to ring formations, however,there are many factors. that contribute or aid amechanism. Due to this complexity it is notpossible to study each factor in isolation. Toovercome this problem investigations rely upon anempirical approach, past history and industrialobservations.
Using a combination of both XRF chemicalanalysis and petrographic analysis, it is possibleto determine the mechanism most likely to cause abuild-up. This paper discusses transition zone andkiln discharge rings that have caused operationalproblems over the last few years. The investigationfound that the rings were formed by a combinationof combustion thermodynamics and freeze/thawmechanisms. There was no evidence of any alkalisulphate or sulphate spurrite induced rings.
Mechanism of ring formationThe main mechanisms for rotary cement kiln ringswere categorised by Rumpfm into the followinggroups:
0 melting or softening of the surface due tofriction
0 melting or freezing from the loss or input of heat
0 interlocking of particles that have been built-upby particles held together by surface forces
0 interlockirg of fine needle like particles
0 electrostatic attraction
The source of material can also be categorised asthere is a number of streams available, as shown inFigure 1, that can effect the composition.
Thus, it can be seen that ring formation is adynamic process with a number of streamsaffecting the composition at any point and anumber of different mechanisms which can bindt h e m a t e r i a l t o g e t h e r . T h i s m a k e s a n yinvest igat ion extremely di f f icul t , as i t is notpossible to hold all but one parameter constant sothat its effect can be evaluated. To overcome thisproblem investigations rely upon an empiricalapproach, past history and industrial observations.In rotary kilns most ring formations that cause
process instability are caused by mechanisms 2.3and 4.
Freeze-thaw mechanismsThe freeze/thaw mechanism is used to advantagein the burning zone of cement rotary kilns, in thiszone coating protects the refractory lining fromaggressive chemical attack and reduced thethermal energy loss from the kiln. In fact, in theburning zone, coating will build-up to a steadystate level of some 20 to 30cm in thickness. This isachieved as the rotary action of a cement kiln is anideal environment where temperature fluctationsand tumbling feed will expose a cooler surface tofreeze any liquid.
The f reeze/ thawing mechanism is tota l lydependent on the composition present and thetemperature in the vicinity of the solid. If thetemperature increases or the composi t ionchanges, for example by chemical reaction, then itis possible that the mineral system may reach theeutectic point or congruent melting point at adifferent position along the kiln axis.
The composition of the mineral system providesvaluable information as historical interpretation ofthe concentration levels can be linked to varioustypes of rings. At a fixed temperature, the mineralconcentration determines whether or not theeutectic or peritectic points will be reached. In anindustr ia l environment, i t is not possib le toquantify the exact mineral system that may exist atany one moment in a dynamic- kiln environ-ment. Mainly because the concentrat ions off lux ing and minera l is ing e lements such asalkalies, sulphates and chlorides are changing dueto volatilisation or condensation. Thus, as theconcentrat ions vary, the posit ion of l iquidformation will also vary along the kiln axis. Animportant source of alkali, sulphate and chloride isfrom the electrofilter dust being returned to thekiln. This dust can contain concentration levelsmany times that of kiln feed which, and if notmonitored, can cause rapid concentration build-up.
The role of alkali salts and alkali aluminatesMany investigations into the role of alkalies,sulphate and chlorides in ring formations by freezethawing have been undertaken and are welldocumented(4). (5). (6). (71. Choi and Glassern discussthe role of sulphur in c l inker product ion bysynthesising, calcium langbeinite (CaL), calciumaluminosu lphate (&A&) and ca lc ium silico-sulphat’e (C&,S) from chemical reagents. Thepresence of sulphur has both beneficial andadverse affects: it improves burnability by actingas a fluxing agent.
Choi and Glasse@) found that at low tempera-tures, below l,lOO’C, the evaporation process is
WORLD CEMENT DECEMBER 1590
dominated by alkali sulphates. However, this is indirect contradiction to Holderbank investigationswhere the low temperature evaporation process isdominated by alkali chlorides. However, the latterprocess is more in line with what is observed in anindustrial process.
Alkali sulphates and chlorides have possibly thelowest eutectic point in the clinkering system:K2S04-Na2S04 binary system has a eutectic pointof less than 900%. The source of alkali andsulphates is either from volatilisation from the feedentering the burning zone or a sulphur rich fuel. Aspreviously mentioned, from 1 ,lOO% upwards, thevolatilisation process is dominated by alkalisu lphates and chlor ides. Since the onlymechanism of ‘bleeding’ the system in a long wetkiln of alkali sulphate or chlorides is by dust loss orsubstition in the clinker phases, it is easy to seehow concentration can quickly reach criticalleve ls .
As the alkali salts are transported, via the gasstream towards the feed end of the kiln the dewpoint temperature wi l l be reached al lowingcondensation of alkali sulphates. In the zonewhere alkali sulphates can remain liquid its lowsurface tension will ensure that it wets the clinkercrystals present. The ident i f icat ion of alkal isulphates can be done both chemically and micro-scopically. If sulphate is a major mechanism, thenit would be expected that the percentage SOS,Na,O or K20 found in a rin,g would be several timesthe amount found in clinker. Also, if a sample isprepared for microscopical observation, then alkalisulphates can be high-lighted by potassiumhydroxide etching, which makes the identification
Table I The Chemical analysis of the different rings
reasonably straightforward.The ferrite and aluminate phases, C4AF and &A,
and alkali aluminates must be considered in ringformation as they are a significant component inthe clinker matrix, accounting for around 17-20 percent of the total composition. With an aluminamodulus of 1.38 in a pure &A-C4AF mix, theeutectic point will be reached at 1338OC. However,substitution of Na+l and K+l ions can occur in theferrite and aluminate phases, but this does notnecessarily mean that the eutectic point willdecrease. In fact Bogue(16j reports for the ternarysystem K20-CaO-A1203 the eutectic point is above1300%. The KA-CdAF-C2F system was similarshowing a eutectic point, again above 1300°C. Astudy of the different systems in which Na+l couldbe susbtituted into &A or C4AF similarly showedthat the eutectic point was about the same level asif K-7 was subst i tuted. So even though thealumina and the ferrite components will determinethe potential liquid phase, it is the presence ofsulphate and chlorides which will determine theeutectic point or congruent melting point at thelower temperature range in a cement kiln.
Spurrite formationSpurrite formation should also be considered atthis stage as it has long been associated with ringformations. Spurrite or sulphate spurrite has beenrecognized as a contributor in ring formation by theintergrowth or matting of the distinct prism shapedcrystals, The formation of spurrite Ca; (SiO&C03, has been extensively studied;(l). (lo). (l’) andrecently Bolio-Arced and Glasser@b investigatedthe role of mineralisers H20, F and Cl in the
Kiln No
Location (m)
S a m p l eDate
Na,O
K20
so3
p205
LOI
6
Clinker2116l89
0 . 7
0.11
0 . 5 3
0 . 0 6
0 . 3 2
6 6 6 5
3Om-36m 21m O m 3 0 m
Ring Ring Nose Ring Ring2611189 717189 1 o/5/89 27111185
0 . 7 0 1 .5 0 . 7 0 . 5 3
0.14 0 . 5 0.11 0 . 1 0
0.55 2.60 0.57 0 . 7 7
0.11 0.10 0.12 0 . 1 2
0.71 3.22 0.56 0 . 3 2
S R
AR
L S F
% Liquid (Lea)1338°C AR> 1.38
% Liquid (Lea)1338=X AR < 1.38
14cvc
2 . 6 7 2.63 2.29 3.52 2 . 5 6
1.65 0.86 1.21 1.46 1 . 4 1
9 4 . 4 8 3 . 3 98.4 9 5 . 7 8 1 . 2
21.3% r. 18.1% 26.4%
2 4 . 3 I+; 1:: 19.1 27.1
Flaw Meal Fly Ash
lnsutflated oust
e
Coal AshAlng
Clinker Oust
VolatIlizeed Elements Combustion Gas
Figure 7. The source of material can also be catagorised asthere is a number of streams available that can effect thecompos i t ion .
formation of spurr i te. A number of react ionmechanisms have been proposed for the formationof spurrite with the reaction frequently beginningwith either C&S or C$S.
It is generally accepted that spurrite is not- stable above 900%. Thus, if the alite mechanism is
responsible for spurrite formation, then the alitemust be transported to the cooler region in the gasstream. For alite crystals transported this way, it isonly a matter of time before the C3S will react withCO2 or SO3 to form spurr i te. Bolio-Arceo andGlassero) also studied the mechanism of spurriteformat ion f rom C2S with CaF2 and CaClz asmineralisers in the reaction species. It was foundthat at least 0.2% CaC12 or CaFl was required. Therole of spurrite in ring formation can easily bemisunderstood, particularly if CaFz is available, forwith these compounds present, a liquid phasewould be produced, raising the question, ‘Which
or the adhesion by freeze/thawing? Investigationsconducted at Holderbank suggest that r ingformat ion is a combinat ion of sol id i f icat ionbinding the spurrite crystals which further assistswith crystals growth.
Regardless if spurrite is suspected of being thebinding mechanism, then microscopic examin-ation will easily identify these crystals by their longprismatic, needle-like shape. However, it must bepointed out that investigations(‘l) have shown that.the concentration of spurrite can vary radiallythrough a ring and, at or near the hot surface theconcentration of spurrite can be very small. Itwould therefore be recommended that a radicalcross-sect ion of a r ing be sampled whenexamining for spurrite.
comes first - the interlocking of spurrite crystals rings.
Ash ringsAsh rings are worth mentioning briefly as they havebeen historically associated with ring formations.In coal fired kilns ‘ash’ rings have been reported toform in the transition zone and cooler inlet areas.These rings are formed as liquified ash, from theflame, settles on the surface of clinker crystalscreat ing areas wi th h igh SiO;, and low CaOconcentrations. In these areas only belite can beformed. Holderbank has reported that the chemicalcomposition of these rings is similar to ordinaryclinker. Microscopically, these rings are veryporous wi th both ash and c l inker part ic lesaggerating to form particles in the range of 100pmto 350pm. Cooling by rotation of the kiln or fromcolder secondary air will ensure solidification ofthe liquid phase. The presence of belite streakscaused by the welding together of the crystals byash drops is commonly associated with these
SF7 Clinker.
c.5 CIinker
Figure 2. SiO,-Al,O,-Fe,O, Ternary diagram.
industrial observations and interpretationsRings forming in Kiln 6 have, on occasions, causedsevere operating problems to the point where ithas been necessary to stop production. The ringswere forming in the upper transition zone and atthe kiln discharge (nose ring). It was initially feltthat rings forming in the transition zone weresulphate rings caused by excessive SOs beingreturned in the electrofilter dust. While the ‘nosering’ formations were caused by dusting, as theclinker cooled by secondary air at approximately500°C, it would transform belite from the beta togamma type. The dilatation of the belite crystal asit undergoes this transformation will causedisintegration of the crystal. However, the gammabelite transformation is uncommon as a high LSFwill cause a slight excess of lime to remain inbelite which acts as stabiliser.
Extensive investigations “‘sing both XRFanalysis and petrographic examination, werecarried out on the rings and the followingdiscussion shows that a completely differentmechanism was responsible.
The chemical analysis of the different rings isshown in Table 1, while Figure 3 and Figure 10 formpart of the petrographic examination.
Transition zone ringsThe chemical analysis of the K6 ring at the 30-36mmark on 26 January, 1989, shows no abnormallevels of alakali, SO3 or Cl, in fact the concen-trations are similar to normal clinker. The silicaand alumina ratio are 2.63 and 0.86, respectively.While the silica modulus is normal for ordinaryclinker the alumina modulus is very low. Plottingthe alumina and silica modulii on the ternarydiagram, Figure 2, shows that the composition hasa tendency to form rings; however, this tendency isonly slightly more than normal SR clinker. WhileSR clinker is known to form a thicker coating in theburning zone, it could not be said that unwantedring formation was associated with this type ofclinker production. The percentage liquid phasepresent in the sample, as determined by Lea(ln* islow and calculated at 12.4 per cent. Even thoughthe sample has a low percentage liquid the highiron content means that the matrix viscosity will below and effectively wet any surrounding particles.Petrographic examination is shown in Figures 3and 4; two different sections of the ring at differentmagnifications. In this section the belite has beenetched blue, alite is etched brown and the closedpores can be seen as black areas. The very densenature of the ring is evident by the close packingstructure of the different phases and a very lowopen porosity. Figure 4 shows that the matrix isferrite rich with the ferrite phase being identifiedby its unetched light grey appearance. There is nosign of any alkali sulphate and as the ferrite phasehas a low viscosity it is the most likely bindingagent in this case. The freeze/thawing of the kilnfeed by the tumbling motion is further enhanced inthis area by the increases or decreases in the heat
Figure 3. K6 Ring 3Q36m.
Figure 4. K6 Ring 3036m.
Figure 5. K6 Ring 27m.
flux profile due to combustion thermodynamics.Mathematical modelling of the heat flux profilealong the axial length of the kiln shows an areafrom 20m to 35m where, given the right chemicalcomposition, the eutectic point could easily bereached as a result of a changing temperatureprofile. The heat flux profile is that of a long lazyflame with the flame temperature dropping from
1460°C, at 20m to 129OOC at 26m then increasingagain-to 13OOOC at 29m. Thus, the most likelymechanism for ring formation is an increasingflame temperature combined with a higherpercentage of liquid ferrite phase. The liquid phasewould be solidified by the tumbling kiln charge’.
Figure 6. K6 Ring 21m.
Figure 7. K5 Ring 30m.
Figure 8. K5 Ring 30m.
The chemical composition of the K6 ring at the21m mark on 7 July, 1989, has a silica and aluminaratio of 2.29 and 1.21 respectively. Plotting thesemodulii on the ternary diagram, figure 2, showsthat its composition has the greatest tendency toform a ring. The percentage liquid phase, approxi-mately 23.4 per cent, is higher than the ring formedat the 30-36m mark, but only marginally higher thannormal clinker at 1,338OC. The alkali content,KzO(0.5%), NazO(1.5%) and S03(2.60%) are higherthan typically found in clinker. liowever, even atthese concentrations it would be unlikely thatalkali sulphates could be the binding mechanism.Petrographic examination shows that the ring is
very dense with almost no porosity. Also, as wouldbe expected for material in this section there wasalmost no alite with belite being the major phasepresent. The belite crystals varied in size from 10 to50 pm; the large crystals would suggest that atemperature around 1500°C was reached. Thebelite structure was internally disorganised, withwhat appears to be alkali sulphate on or near thesurface. Figure 5 shows a section of the ring with aband of idiomorphic periclase, round greyishcrystals, which is indicative of the ring being incontact with a dolomite lining. Associated with thepericlase is a large amount of free lime. The matrixis predominately ferrite with a small amount ofcoarse aluminate. Figure 6 is a higher magnifi-cation view of the sample further away from thepericlase band. The shape and internaldisorganisation of the belite make it impossible to
interpret; however, it is again most likely that thebinding phase is the ferrite rich matrix. The heatflux profile reduces significantly from 20m to 25m,thus any small changes in the axial position of thefeed would expose the feed to large changes in thesurface temperature. As mentioned earlier theflame temperature changes from 1460°C at 20m to1290°C at 26m, but it must be remembered thatthese predictations are based on a mathematicalmodel and in the real environment the combustionthermodynamics could shift the heat flux profile inany direction along the kiln axis. Again, it wouldappear that a varying heat flux profile in the regionof 20m to 27m is inducing ring formation by afreeze/thaw mechanism of a ferrite rich matrix.
The chemical analysis of the K5 ring gives analumina and silica modulii of 1.41 and 2.56,respectively. Plotting these values on the ternarydiagram, Figure 2, shows that the ring formationtendency is not all that dissimilar to ordinaryclinker. Petrographic examination of the ring, asshown in Figures 7 and 8, reveal a very densestructure with some closed pores (black areas) andeven less open pores (mat grey in colour). The mostevident feature in Figure 7 is the nesting of belite,blue etched crystals, which could be attributed toan inhomogeneous feed. Figure 8 shows a highermagnified view of the ring. The alite crystals,etched brown, have a maximum size ofapproximately 50pm but many small alite crystalsare also present. The matrix is predominatelyferrite rich, particulariy in areas of belite clusters.Some aluminate can be seen as a slightly darkermat grey colour. Similarly, the mathematicalmodelling of the heat flux profile in this kiln is verysimilar to Kiln 6 with an increase in the flametemperature around the 30m mark. Thus, it wouldappear that the same mechanism is responsiblefor the rings. That is varying flame temperatureassisting a high liquid content which is beingfreezed by a tumbling kiln ‘charge’.
Nose ringsampleThe sample labelled ‘nose ring’, 10 May 89, has achemical composition which is very similar toordinary clinker. The percentage sulphate is theonly minor constitutent that could be consideredslightly high. The silica and alumina modulii are3.52 and 1.46, respectively and plotting these
Figure 9. K6 ‘Nose’ Ring.
figure 10. K6 ‘Nose’ Ring.
values on the ternary diagram, Figure 2, shows thatthe ring composition has the least tendency of allthe samples to form a ring. Petrographicexamination of this sample, is perhaps the mostinteresting, and typical views are shown in Figures9 and 10. The sample has a very open porousframework of crystals cemented together by aninterstitial matrix of fine aluminate and ferritephases, as shown in Figure 9. The major phasepresent is an idiomorphic alite with a size rangingfrom 240pm to 100pm. The larger aiite shows signsof decomposition with cracking and secondarybelite formation, see Figure 10. The belite crystalson the other hand appear mainly as clusters withcrystal size ranging from 10 to 50pm. The etchingof belite shows areas of different reactivity whichis believed to be caused by alkali sulphate on ornear the crystal surface(15,.
Both the size of the alite and belite crystalswould suggest that a sintering temperature of atleast 1500% was reached. In addition, the alitedecomposition would suggest that the coolingrate, between the burning zone and the kilndischarge, was too slow. Thus, if the kiln coolingzone was relatively long and hot then hot clinkerwith a mobile matrix will crystallize as it meets thecooler secondary air as it leaves the kiln. The fact
proposed mechanism in this case would be a ver)hot burning zone combined with a hot cooling zoneso that as the clinker leaves the kiln, any clinkerdust re-entering the kiln will adhere to a mobilematrix phase and solidify on contact or as it comesinto contact with coler secondary air.
ConclusionsIt is concluded that ring formation, in Kiln 6, iscaused by freeze/thawing brought on by acombination of combustion thermodynamics anda low alumina ratio slurry. Mathematical modellingof the kiln heat flux has shown that the flameappears to be long and lazy with an increase in theflame temperature around the 30m mark. Thechemical composition has also shown that thealumina modulus is consistently low allowing for agreater percentage of liquid phase to be present atlow temperatures and that it is very near theeutectic point of the &A-C4AF system. It is alsopossible that an inhomogeneous feed may furtherexacerbate the problem.
There was no evidence to suggest that alkalisulphates or chlorides formed part of the bindingmechanism.
References
(1) OPITZ, D - Ring and Coating Formation in Cement KilnsSchr i f fenre ihe der Zement indust r ie , H:41/1974. V e r e i n dDeutscher Zementwerks EV Dusseldorf.(2) RUMPF. H - Prooerties. Bindino. Mechanisms and Strenothof Agglomerates Aufberei?ungs-Tec’knik. No 3. 1970. ”(3) LONG, G R - Deleterious Raw Materials and Their Effects onClinker Burnability. Proceedings of the fifth fnternationafConference on Cement Microscopy March 14.17,1983. NashvilleTennessee USA.(4) SPRUNG, S - influence of Process Technology on CementProperties. Translation ZKG No 10 ~577 1986.(5) CHOI GANG-SOON and GLASSER. F P -The Sulphur Cyclein Cement Kilns: Vapour Pressures and Solid-Phase Stabil ity ofthe Suiphur Phases. Cement and Concrete Research V78 ~3671988.(6) SYLLA, H M - Untersuchungen zur Bildung von Ansatzr ingerin Zementdrehofen. Zemenf-Kalk-Gips No 10 ~499 1974.(7) STRUNG, J. KNOFEL. 0. DREIZLER. S, DREIZLER. I, andBERGISCHGLADBACK. Influence of Alkalies and Sulphur onthe Properties of Cement Parts I. II and Ill. Zemenl-Kafk-Gips No5 ~130 1985.(8) MACGREGOR MILLER. F - Dustv Clinker and GrindabilitvProblems. Rock Products ~152 April i98O.(9) BOLIO-ARCEO. H and GLASSER. F P - Formation ofSpurrite Cae(SiO&COJ. Cemenf and Concrete Research V20(2)p301 1990.(10) SYLtA, H M - Investigations on the Formation of Rings inRotary Cement Kilns. Zement-Kalk-Gips (10) p499 1974.(11) BECKER. F and SCHRAMLI. W - Build-up of Rings Causedby Spurrite Formation. Cement and lime Manufacrure V42(9)p91 1969.(12) HOFMANNER, F - Microstructure of Portland CementC l i n k e r . Holderbank Managemenf and Consul t ing L td .Holderbank Switzerland 1973.(13) IMLACH. J A - Determination of the Cause of RingFormation in Kiln No 5. Darra. Holderbank Management andConsultina Ltd. Reoort No MA8613355iE.(14) IMLACH. J A 1 Analysis of Cause of Ring formation in Kiln6 at 98-121 Feet from Kiln Outlet. Holderbank Management andConsultino Ltd. Reoort No MA8913613lE.(15) IMLACH: J A and MISTELI. 8 - Texture Evaluation of Ringand Slab Samples Taken from Kilns 5 and 6 at Darra.
#Holderbank Management and Consul t ing Lfd. Report Nothat solidification take:s ulace as the materialdischarges from the kiln is evident by the rapid MA89l758lE.
cooling of the matrix. Petrographic examination of (16) BOGUE. R H - The Chemistry of Portland Cement.
the matrix shows it is composed of evenlyReihhold Publishing Corp. 1965.
distributed fine ferrite and aluminate crystals. The(17) LEA, F M - The Chemistry of Cement and Concrete 3rdedition. Edward Arnold (Publishiers) Ltd. 1983.
WORLD CEMENT DECEMBER 1990
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 10
Kiln Build-Up Meeting
KILN BUILD-UP MEETING
5 May 1998 - Fairfield House, Stanhope
Present: P.GreenoJ. CollinsonD.BelemyA.BainbridgeK.Atkinson
M.MutterL.EvansA.Edwards
J.WilsonS.Dodd
A meeting was organised to review the causes of kiln build-ups at Weardale, Cookstown and Dunbarworks. Each works has specific build-ups and the aim of the meeting was to review any commonalityin the build-ups and methods for reducing the frequency of stops. A review of each works past andpresent problems was the basis of the meeting.
Weardale Works
Three areas of build-up appear at Weardale
(iii)
Lepol roof and kiln inlet chute, with material often falling off the roof and into the kiln.Kiln back-end, often a long build-up of around 20 feet long and up to 2 foot thick. Feed canoften be held up in this area causing problems with overloading of the riddlings system.Back of the burning zone - this. material can often be reached and removed by water jetting.
The works are currently using open cast coal with a sulphur level of 0.9 - 1 %, and around 30 %petcoke with a sulphur level of around 5 %. Recently water has been injected into the flame at around 5litres per minute, which has had the benefit of tightening the flame; The water injection has also hadthe effect of softening and reducing some of the build-up in the burning zone. It is proposed to increasethe water addition rate progressively to attempt to remove build-up further back in the burning zone.
The back-end build-up is thought to be alkali-sulphate based. Sulphate to alkali molar ratio is runningaround 1.5 - 1.7 on OPC and 1.7 to 2 on SRC. Slag is also being used in the raw mix, which is having anumber of effects:
(i) Kiln outputs have increased as the level of slag used has increased.(ii) The slag tends not to create as much build-up.
The slag addition is reducing the overall sulphate input as it is replacing higher sulphate shale. Theworks is also attempting to select the best shale to minimise sulphate input.
Additional problems are experienced with the production of SRC, where nodule breakdown on thegrate is an issue leading to a dusty kiln and increased bed blinding. On occasions the kiln can build upin 48 hours on an SRC run.
Cookstown Works
Cookstown reported that whilst in the past many similar areas of build-up occurred, steps have beentaken to reduce their formation. Since 1992 the cyclone dust has been removed from the system andmixed with the CKD. This material is then transferred to the cement mills and incorporated into thefinal product. It was commented that if the cyclone dust is returned to the process then the build-ups re-occur very rapidly. The benefit of this is two-fold, the first effect is to reduce bed blinding and thesecond is to reduce the sticky alkali-sulphate material entering the kiln and forming a build-up.
Grate/chute build-ups still occur at Cookstown, although their effect has been minimised by theinstallation of silicon carbide refractory on the roof (around half of the length of the above calciner)
and sides of the Lepol grate, and also in the chute. There are no reports of any difficulties in keepingthe silicon carbide in these areas. The grate and chute have around 14 air cannons installed althoughtheir effectiveness has not been quantified. The chute and hearth were also modified around the sameperiod to allow an increased area for gas flow.
1997 saw a significant number of stops due to long, tapered build-ups through the burning zone. Thesewere often hard build-ups, and due to hardness and the shape of the taper, were difficult to remove byany other method apart from stopping the kiln and digging out the build-up. These build-ups wereassociated with the burner itself (a new FCT pipe) and the position of the burner. Since the re-installation of the burner and its alignment, only two burning zone build-ups have occurred, both beingrings as opposed to tapers. The result of this is that the rings can be shot away and a kiln stop avoided.
Dunbar Works
Dunbar works manages to achieve a good burning zone coating (although sometimes a little deficient atthe nose ring). The build-up problem would appear to be around the 35 and 45-metre length from theburner, with distinct rings being formed at these points. There is no real build-up in the riser, and thereis no riser-cleaning or air cannons. The effect of the rings is to create a dam in the kiln causing rawmeal to be held back and spill out of the back end seal.
Amongst recent solutions are the speeding of the kiln to 4 rpm to move the material away from theseal, modification of the seal to reduce spillage and a rubbing ring to be installed later in the year. Theworks have been trying to identify the cause of the rings. The’ stage 2 inlet oxygen is controlled at 4 %in an attempt to reduce sulphate volatilisation. Observations are that there is a link between NOx andspillage, and that less build-up is present if the fuel split between kiln and precalciner is kept around the40/60 % (worse spillage at 45/55 % split). The build-up is sometimes claimed to be clinkered.
Discussion
Having identified the types and areas of build-ups in each of the kilns, it is important to classify thetypes of build-up being formed. It would appear that the experiences of Dunbar could be a differentproblem to those at the back of the kiln at Weardale (and those previously experienced at Cookstown).
Dunbar need to evaluate the composition of the build-up to identify whether it is due to volatilerecirculation or whether the rings are due to clinker being carried to the back of the kiln and depositingon the sticky melt in the kiln. Such build-ups can be characterised as a dense yellow/brown material,made up of material with fine particles. The principle of analysing the “building blocks” - the size ofparticles in the build-ups - will be pursued by Technical Centre on samples of build-up received in thefuture.
On a kiln where cooler control is poor, and fine, dusty clinker is periodically produced due to over-burning, such build-ups can be expected.
In terms of sulphate control for Dunbar, much of the raw material sulphate is lost in the preheater toweras it is present in the raw meal as sulphite. This acts as a bleed for sulphur in the system, although somesulphate is returned to the system via the GCT dust. If the build-ups turn out to be sulphate based thenfurther examination of the volatile cycles is required.
Cookstown build-up is currently in the burning zone, and as previously stated, tend to be rings asopposed to tapers. It is likely that the rings are originating from the return of the dust from the coolerwhen the air cannons are fired on the IKN. The solution here would be to attempt a redesign of the inletaround the IKN to reduce the use of the cannons and therefore the amount of dust returned to theburning zone.
This leaves a comparison of the three Lepol kilns to review how to reduce the back-end build-ups atWeardale. The obvious difference is that the cyclone dust at Cookstown is completely removed fromthe system whereas this is not carried out at Weardale. When this method was tialled at Weardale, the
cyclone dust was removed from one kiln and returned to the other kiln. The kiln with cyclone dust, notsuprisingly, performed poorly. The kiln without cyclone dust resulted in a reduction in output with ahotter kiln. Whilst the trial was possibly not conclusive, the removal of dust from the cyclones andaddition to the cement mill at Weardale will potentially increase the cement alkali level above the 0.6soda equivalent level.
All of the riddlings are returned to all three kilns. Riddlings are often screened on other Lepol plants sothat the smaller fractions, which have the higher volatile contents, can be removed from the kiln systemand further reduce volatile cycles. It is proposed to trial this at Cookstown with the results being fed onto Weardale.
Cookstown comment that removal of the CKD and cyclone dust will reduce the soda equivalent in thecement by around 0.02. It is also commented that the amount of cyclone dust and the level of alkalis inthe clinker could reduce by bleeding off this material. In the trial carried out at Wear-dale in removingthe cyclone dust, around 2 tph material was collected, with around two thirds of the material having tobe dumped in the quarry.
The quantities and qualities of the materials around the system need to be reviewed and compared withCookstown, to examine whether the dust could be returned to the cement mills. This will also allow asulphate balance to be carried out to examine the extent of circulation around the system. Therecirculation of the volatile materials - alkalis and sulphates - is related to effects in the burning zonesuch as flame impingement and reducing conditions in the flame, as well as the high sulphate to alkaliratio. Calcium sulphate will decompose in the burning zone due to contact of the flame with thematerial bed in the presence of CO, and also excessive temperatures in the burning zone. Therefore it isimportant to ensure that a tight flame can be produced to avoid the flame touching the bed.
This, in principle, can be achieved by the use of a bluff body in the burner pipe. It was agreed to trialsuch a device when an appropriate design is provided by the Technical Centre. The position and angleof the burner will also be review. Both burners are in different positions at present but this has notshown any significant differences in operation. If the burner is pushed into the kiln the secondary airwill be better entrained and produce a narrower flame.
Coal mill and oxygen control at Weardale will also be reviewed so a more stable operation in theburning zone can be achieved. NOx control is currently used as a control parameter and variations inthis parameter, along with the SO2 at the back of the kiln can also give indicators as to the extent of therecirculation in the system.
An action plan of areas to review has been compiled as a result of these discussions.
2.
3.
4 .
5 .
6.
7.
8.
9 .
Process Parameters
02, NO,, S02, CO, (stack and back end).
Kiln feed, temperature profile and suction profile.
Secondary air temperature, coal feedrate.
Cement quality
- sulphate - max 3.5%- alkalis - max 0.6%
Cement quality - slump- early strength/reactivity- 28 day properties
Effect on product properties of any consideredchange.
Alkali bleed via auxiliary stack.
Kiln/cooler exhaust/dust to burning zone.
Lepol best practice for dust return/build-up.
10. Secondary firing.
1 . Cookstown max speed 1.8Weardale max speed ?Does this affect build-up?
2 . Silicon carbide on grate areas/kiln areas - SCbricks.
3. Grate chute design at CKN - compare withWeardale and hearth design.
4 . Grate Operation
- bed depth and variation (fixed speed)- doors open/closed- pan angles
5. Recirculation fan - use/benefits/effects.
6 . Microphone on grate - information on bed blinding.
Raw Meal(either for SR or OPC)
1. Fluorspar addition- benefits?- where in process?
2. Secondary r.m.‘s- Shale ‘Z’ usage- S l a g- PFA (up to 3% shale replacement -
nodule problems) .+ nodule strengthener to increaseof pfa
- increased low stone usage
3. Raw meal residue- now- with secondary r.m.‘s
4. Chemistry of particle range in raw meal.
5. Raw meal variability
use
- effect- improve
1.
2.
3.
4.
5.
6.
7.
8.
9.
Coal/petcoke mix - impact of fuel sulphur - waterInjection
Flame- bluff body- firing pipe position in relation to nose ring- firing pipe angle- secondary air temperature
Coal Residue
Coal ash composition and % in coal.
Fuel blending in coal store.
Fuel composition - frequency of sampling.
PF moisture < 1%.
Coal mill control.
NOx/kiln burning strategy (N.B. control of kiln withlow NOx burner?)
10. Kiln camera - Quadtech?
11. Shell temperature for build-up.
12. Sulphate balance/SO2 recirc/grate material SO4sample.
13. Inleaking air through system.
14. Temperature profile through grate - comparisonbetween works.
15. Removal of coal mill cyclone off cooler.
1 . Quantity of riddlings.
2. Quality and psd of riddlings.
3. Screening - possible without breaking up nodules?
4. Position of riddlings return - back onto grate vs kilnchute.
5. 1 Kiln no riddlings return, other riddlings from bothkilns - high alkali clinker.
6. Nodule strength improvement.
Cyclone Dust
1.
2.
3.
Quantity of dust - OPC and SR.
Quality of dust- chemistry- particle size- hot/cold cyclones- efficiency of cyclones between kilns -
compare with CKN. Vortex finders incyclones.
Return of dust to cement mills- how much
4. Cost of tipping dust? Can it be sold?
5. Return to other kiln.
6. Return all/proportion to noddy pans/elsewhere.
7. Predict effects of all/partial removal.
8. Pelletizing of dust.
9. Intermediate fan efficiency.
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 11
Cement Seminar- Rings, Balls, andBuild-Ups
Table of Contents
Page
1. INTRODUCTION
2. LOCATION OF RINGS
2.1 Classification
1
2
2
3. THEORETICAL ASPECTS OF RING AND DEPOSITFORMATION 4
4. CHARACTERISTICS OF VARIOUS RING ANDDEPOSIT TYPES 5
4.1 Exhaust Fan Deposits 54.2 Slurry Rings 64.3 Cyclone and Grate Preheater Deposits 74.4 * Meal Ring (Calcininq Ring) in Long Kilns 84.5 Middle Rings in Large Preheater Kilns 94.6 Sinter Rings (excl. coal-ash rings) 104.7 Coal Ash Sinter Rings 104.0 Clinker Rings / Cooler Inlet Deposit 124.9 Kiln Charge Balls 12
5. METHODS OF REMOVAL/ELIMINATION 13
TABLES 1 - 7
APPENDICES I - III
RINGS, BALLS AND BUILD-UPS
1. INTRODUCTION
Rings and deposits are accumulations of solidmaterials (from the powdery kiln charge) in therotary or static sections of clinker productionlines. They have been encountered since the earliestdays of rotary kiln production, with each develop-ment in process technology, e.g. grate and cyclonepreheaters, grate cooler, bringing with them theirown specific type of deposit.
Rather than being of academic interest, ring anddeposit formation has an appreciable influence onplant operations, frustrating-operations personnelby their impairing or even impeding production, andannoying the company management by lowering produc-tion (and sales) and increasing production costs.
As a direct consequence of rings and deposits, thegas and material flow through the kiln is restricted,resulting in a reduced kiln output. Especially inthe sinter zone, the presence of rings can interferewith combustion of the fuel and can result inimproper combustion. From time to time unstablerings and deposits can break away leading toblockage or mechanical damage in the cooler, or incyclone blockages. The partial shedding of coatingfrom the exhaust fan blades results in severe vibra-tion which mostly requires a short shutdown forcomplete removal. The breaking of a ring almostalways causes a flush of material into the burningzone and a temporary loss of stable kiln operations.
The formation of deposits in cyclones results inextra costs for the labour needed to remove thedeposits by poking. The introduction of air canons(big blasters) provides a method for their regularautomatic removal and has been installed in Groupplants with persistant preheater blockages.High pressure water jets may also be employed.
In the worst cases, a complete shutdown is necessaryto allow entrance to the affected area and mechani-cal removal of the blockage with compressed airdrills. This shutdown invariably weakens the sinterzone refractories, and accelerates the next shutdownfor rebricking.
2. LOCATION OF RINGS
2.1 Classification
Unwanted build-ups may be classified with regardto the type of material from which they areformed, either sintered or unsintered. Withinthese two groups the various types can beclassified as follows:
unsintered:----------. exhaust fan deposits. cyclone and grate preheater deposits. slurry or mud rings. meal rings
sintered:--------. middle ring. sinter ring. clinker ring. "snowman" in grate cooler. kiln charge ball
Process technological characteristics of suchbuild-ups e.g. kiln type, location, temperature ofgas and kiln charge can be seen in Table 1.Material technological characteristics e.g. stateof kiln charge, enrichment in various elements,and type of texture are summarized in Table 2.
The location of the various types of the aboverings and deposits can be seen in Fig. 1.
CYCLONE
PREHEATER KILN
GRATEI -
PREHEATER
KILN- -
WET KILN c
.
\
/
/
MUD BALLSSLURRY RING
/
RINGS AND BUILD- UPS IN
DIFFERENT KILN SYSTEMS
ASH RINGSL/D - 5-7
/
COATING ON
INLET TO
COOLER
MIDDLE RINGS LARGE DRY KILNSMEAL RINGS (LONG KILNS)L/D - 7-13
SINTER RINGSL/D - 2-7
CLINKER RINGSL/D- O-2
3. THEORETICAL ASPECTS OF RING AND DEPOSIT FORMATION
Although of much practical significance, littlequantitatively based, fundamental knowledge isavailable on the formation of deposits from solidssuspended in gas streams. In a qualitative way,however, the more important features of such pro-cesses are known.
The formation of a deposit is always a dynamic pro-cess in which the factors responsible for formationoutweigh the forces of degradation. In general, thestronger the forces of destruction, the more unli-kely the chance of deposit formation, but when thisdoes occur, a strong, hard to remove agglomerationis the result.
After the transport of material to the area of depo-sition, a definite force is required to make itadhere to the wall. This can range in magnitude fromthat caused by turbulence within the gas stream,increasing to centrifugal forces when the streamchanges direction, to that due to mechanicalpressure. Whereas preheater deposits involve thefirst two, mechanical pressure certainly plays a partin ring formation within the rotating kiln.
The forces according to Rumpf considered to causedeposit formation can be grouped as follows:
A - melting or softening of surface due to frictionor collision
B - melting or freezing due to addition or removalof heat
c - interlocking of aggregates built up of finerparticles held together by surface forces
D - interlocking of long fibrous particles
E - electrostatic attraction
The mechanisms B, C and D are the ones encounteredin kiln operations. In general, the finer thepowder, the greater the tendency towards agglomera-tion, and in many cases the absence of particlesunder a critical size (e.g. 5 urn) ensures freedomfrom deposition.
4. CHARACTERISTICS OF VARIOUS RING AND DEPOSIT TYPES
Tables 3 and 4 contain a list of typical proper-ties of rings and build-ups encountered within the"Holderbank" Group plants (with full chemical analy-sis being provided in Appendices I, II and III).Included are such factors as volatile element con-centrations and moduli of the deposited materials.As an indication of the texture, the size of thepores and the particles or aggregates of particles,from which the materials were built up, is given. Inmany cases the mineralogical composition is alsogiven.
4.1 Exhaust Fan Deposits
In the case of kilns with pressure filter systems,in which unfiltered dust-laden gas passes throughthe exhaust gas fan, deposit formation causesproblems. These arise when the deposit falls offone blade, and brings the rotating fan out ofbalance. Deposits of up to 3.5 kg/blade are knownto occur.
Characteristic properties:
Exhaust fan deposits, composed of the finest rawmeal particles are usually red-brown, hard andquite brittle. They exhibit a compact layeredstructure and have a very low porosity of 8%.
Their chemical and mineralogical composition isbasically that of the raw meal but often theplate-shaped clay particles are preferentiallydeposited parallel to the blade surfaces. Due totheir long stay in the system, fan deposits areenriched in the volatile components K20, Na20,so3. Typical values include the following:
LSF 20 - 100SR 1.0 - 1.5K20 + Na20 2.1 - 3.0 %SO3 4.7 - 6.0 %
The SO3 is usually present as anhydrite (CaS04).
Bindinq mechanism:
In this case, the temperature is such that liquidphase involvement - aqueous or molten salts - canbe ruled out.
The dust particles, because of the fan rotation,strike the blade surfaces with a high velocity andare so compacted. As the texture of the surface,after even a short time in operation, possessesundulations in the order 0.5 - 20 urn, the smallerdust particles can be mechanically "locked-on".Subsequent development of the deposit follows byan identical mechanism.
4.2 Slurry Rings (including mud balls)
Characteristic properties:
These occur in long wet kilns and are composed ofthe partially dried kiln charge somewhat enrichedin alkalis and S03. They are soft and can usuallybe broken - and hence prevented - by heavierchains. The H20 content lies between 20 and 30%, arange in which clay materials exhibit a sticky,plastic consistency. The content of the alkaliswhich greatly increases the tendency to adhesion(influence on rheological properties) can be up to10% K20 + Na20, and about the same level of S03.In many cases, balls form (in addition) on thechain links by the same mechanism. A typicalexample of a mud ball is plant I in Table 4.
Bindinq mechanism:
The binding mechanism is the well-known ability ofclays to form a sticky, plastic mass when con-taining the correct quantity of H20, and to hardenon the further water loss. To this mechanism mustalso be added the crystallization of K2SO4 solu-tion and the further strengthening of the struc-ture by formation of CaS04. Photo la gives anexample of such a ring.
4.3 Cyclone and Grate Preheater Deposits
Characteristics:
These deposits form on the roofs, walls, outletand riser pipes of cyclone preheaters, in the hotchamber of grate preheaters, and vary considerablyin appearance and homogeneity. In general, theyhave a light colour varying from cream to brown topink, indicating that the component particles hadnot been heated higher than 1200°C. In some cases,darker zones of harder burnt material can beobserved. Depending on their place of deposition,they range from a dense, compact, definitelylayered structure, hard to break to a porous (30%)material with only moderate strength with lessobvious layering. The former type is typical ofcyclone cones and discharge pipes while the latteris to be found in the transition and swirl cham-bers. Soft deposits can, however, also be found inthe cyclones.
From a chemical viewpoint, this deposit typeusually is characterized by a concentration of thevolatile elements in the following range:
K20 = 1 - 30% so3 = 1 - 35%Na20 = 0 - 2% Cl = 1 - 25%
In some cases, therefore, deposits can occur withno appreciable increase in concentration. Typicalanalyses found for deposits are given in Table 3and Appendix I.
The mineralogical composition of preheater depo-sits differs as would be expected from that of theraw meal in that the clays are essentially decom-posed, and a reaction to form intermediateminerals has taken place. Minerals containing onlythe volatile elements can also be found.
Amongst the minerals found in preheater depositsare the following:
raw meal: calcitequartz
CaC03SiO2
normal intermediate phases:
free limepericlasemayenite
CaOfMgOC12A7
typical deposit phases with low melting point:
sylvite KC1halite NaCllangbeinitearcanite
2CaS04 . K2S04K2S04
typical deposit phases without melt involvement:
carbonate spurrite 2C2S . CaC03sulfate spurrite 2C2S . CaS04anhydrite CaS04
Formation mechanism:
The binding substance in this deposit type is thelow melting point Na20, K20, SO3, Cl based com-pounds. These are molten in the kiln gas and aredeposited on the cyclone walls and pipes, or firston dust particles which then themselves are depo-sited out of the gas stream in these areas.Cooling on contact or with increasing thicknessresults in an appreciable strengthening of theoriginally sticky deposit. Because of the exten-sive duration of stay in the kiln system, a reac-tion takes place with gaseous CO2 and SO3,resulting in the formation of lath shaped spurriteand sulfate spurrite which additionally strengthenthe texture. Typical textures for unsintered, pre-heater and kiln inlet deposits can be seen inphotos lb - 1d.
4.4 Meal Ring (Calcining Ring) in Long Kilns
Characteristics and formation:
The meal rings, often called "calcining rings" inlong kilns, are in their properties and mechanismof formation very similar to those of preheaterdeposits in heat exchanger kilns. This is perhapsnot surprising in that both build-ups occur in thesame temperature zone. Meal rings are mostly lesstroublesome than preheater deposits because often,due to their relatively poor strength, thermalfluctuations, kiln deformation and the action Ofthe material stream, they fall off periodicallyunder their own weiqht. A typical example of a
4.5 Middle Rings in Large Preheater Kilns
Characteristics:
Unlike meal rings, middle "rings" are dense (finegrained) of low porosity, very hard and seldomfall off during operations. Although termed as aring they are rather more elongated, like a band,being often some 15 - 20 m long extending from 7to 11 diameters from the outlet, e.g. 35 - 55 mfor a 5 m Qj kiln. Unlike previous types, thisdeposit is clinker-like in colour indicating itbeing composed of well burnt kiln charge. Perpen-dicular to the direction of deposition, the finelayered structure can be seen showing the cur-vature of the kiln shell.
The chemical composition of middle rings is verysimilar to that of clinker. This is surprisingbecause considering the long duration of the stayin the kiln, no increase in concentration of thealkalis or SO3 takes place, and often the ringshows lower volatile element values than forclinker. Typical analyses of a middlering are given in Table 5.
The minerals found in middle rings are the clinkerminerals alite, belite, aluminate, ferrite andfree CaO, the alite having often decomposed intomicroscopically mixed belite and free CaO,resulting from the temperature at the site of thering being under the lower stability temperatureof alite (i.e. 1260°C).
Formation Mechanism:
The mechanism of bonding is the freezing of theclinker alumino-ferrite melt. Due to a long coolflame, the clinker has a tendency to be fine, andthe smallest clinker particles of 150 - 450 urn arecarried back by the flame and deposited onto thekiln wall in a zone where temperatures of below1250°C exist. The particles immediately freeze inplace, and because the kiln charge is still fine,it does not possess sufficient abrasive action toremove the growing ring. The typical compactstructure of a middle ring can be seen in photo le.
4.6 Sinter Rings (excluding coal-ash rings)
Characteristics:
These occur at the beginning of the sinter zonesome 4 - 5 D from the kiln outlet. They aregreyish-black in colour, strong and are (usually)agglomerations of small clinker pellets andclinker dust. No layer structure is obviousbecause of the presence of large pores and voids.
In general, the chemical composition is that ofthe clinker with no appreciable concentration ofvolatile elements.
From a mineralogical viewpoint, the normal clinkerminerals alite, belite, aluminate, ferrite andfree CaO are observed, with reactions to formbelite and CaOfree, spurrite and belite beingfound with increasing depth in the ring, i.e.decreasing temperature, similar to the case ofmiddle rings.
Bonding mechanism:
The bonding is created by the freezing of the alu-mino ferrite clinker liquid in the case of puresinter rings. This phenomenon occurs especially atthe beginning of the sinter zone, where the liquidphase is just starting to form (approx. 1280°C).Due to the rotation of the kiln, the charge inthis zone freezes with each kiln revolution: a newwet layer sticks on, and with time a thick depositbuilds up consisting of particles of less than 1 mm.
4.7 Coal Ash Sinter Rings
Characteristics:
In kilns fired with a high ash content coal,sinter/coal ash rings can form at 7 - 8.5 D fromthe kiln outlet. They are dense, often layered andsometimes glassy in appearance and built up fromparticles some 150 - 250 urn in size. They arerather less dense and have larger pores and voidsthan middle rings. Photo 1f gives an example ofthe microstructure of such material, showing thecoal ash layers.
From the viewpoint of their chemical and minera-logical composition they are essentially similarto clinker, exhibiting the minerals alite, belite,aluminate, ferrite and free CaO. With decreasingtemperature (increasing ring depth) reactions toform spurrite and calcite take place, and also thetransformation of alite -> belite + CaOf and /3-beliteerbelite. Details of the chemistry andmineralogy are given in Table 6 . No enrichmentof the volatile phases can be observed. Because ofthe enrichment in coal ash, the belite content ishigher than that of the clinker, and tends to befound in layers.
Formation mechanism:
The bonding medium here is the sticky molten coalash particles and perhaps to a slight extent, thealumino ferrite clinker liquid phase occurring bya mechanism such as in Fig. 2 showing thetypical build up during kiln rotation.
Fig. 2: Mechanism for ring formation
ash layer(sticky)
kiln charge
a)
ash layer+ sticking kiln
charge
kiln charge
b)
ash layer /kiln charge /ash layer
kiln charge
c)
The molten coal ash droplets adhere to the exposedkiln lining at a point and temperature at whichthey are still partially fluid and sticky. Whenthis sticky layer passes under the kiln charge oneach rotation, it is assumed that a single layerof the still very fine kiln charge adheres to it.Because of the presence of fine crystalline aliteand the overall occurrence of liquid phase, itmust be assumed that the material temperature atthe position of the ring lies above 126O'C.
The alite crystals are very small and certainlymuch smaller than those of the clinker. Because ofthis, it can definitely be said that the ring isnot formed from clinker dust blown back down thekiln.
4.8 Clinker Rings / Cooler Inlet Deposit (snowman)
Such rings and deposits are formed from normalsize clinker granules and have a high porositycontaining many voids. They are usually nottroublesome to kiln operations as they can easilybe removed. Their composition and mineralogy isidentical to clinker, but in some cases, rings ofup to 3.5% K20 and 3.0% SO.3 have been observed.
The mechanism of bonding is the freezing of theclinker liquid phase as the clinker passesthrough the cooling zone (ring) or on falling downthe chute into a grate cooler, grate kilns beingusually operated so as to have no cooling zonewithin the kiln itself.
4.9 Kiln Charge Balls
Kiln balls occur in cases where a tendency to mealor sinter ring already exists and can be up to 1 min diameter. The chemical composition is, thus, animportant factor. They are usually found upstreamof meal or sinter rings.They are usually made up of already calcinedmaterial and can have a porosity of up to 558,consisting of many fine pores. Often they consistof a hard dense porous core, surrounded by themajority of porous material. The core usually is apiece of coating from say the lower heat exchangersor the transition chamber, and often has a com-position different from the kiln charge in thearea of formation. Differences in composition canbe seen in Table 7.
The mechanism of meal ball formation can be due toeither, or a combination of the following factors:
- stripping and subsequent "balling" of old,excess coating
- agglomeration enhanced by available clinkerand/or salt melt
- ring section acts as a dam, retaining "pieces"of material for long periods. Radial growth ofthe pieces occurs by compaction and adherenceof fresh surface due to continual rollingaction of the pieces/balls over the charge.
In most cases, no liquid phase participation insufficient quantities is possible so that theballs behave like a snowball and by their ownpressure material sticks to the surface. Thismechanism is similar to that of deposition on theexhaust fan blades.
5. METHODS OF REMOVAL/ELIMINATION
An important prerequisite for minimizing the ten-dency to form objectionable coatings and rings, isstable kiln operation. This applies to the com-position, fineness and feed rate of the raw materialand fuel, and burning zone heat control.
The tendency to form coatings in the kiln is reducedby lowering the dust load of the kiln gas.
Objectionable coatings and rings which are formed asa consequence of high concentrations of various cir-culating elements can be obviated by appropriatereduction of the cycles in question.
This can be achieved by:
- Employing different raw materials and/or fuelwith lower concentration of the offendingelement. This is generally not practicable.
- Control of the raw meal milling so as to reducethe concentration of the very fine particles ofsizes under 20 urn.
- Intervention into cyclic process by eitherdiscarding dust in which the circulating elementshave become concentrated, or by means of abypass installation which extracts a portionof the kiln gas.
The penetration of false air into the preheater andkiln inlet chambers should be avoided, as such coldareas will act as sites for preferential build-up.
In order to reduce the tendency to form sinterrings, it is in the first place necessary to reducethe proportion of fusible matter in the clinker,i.e. the lime standard and silica modulus should beincreased. "Coating-inactive" bricks have alsoproved successful in certain cases, in reducing thetendency toward sinter ring formation.
In coal-fired kilns a coal with a normal ash contentshould be employed as coals having ash contents of40% are characterized by a very high tendency toring formation. No general approach can be given tothe effectiveness of other measures, e.g. alterationto firing conditions, as these represent variableswhich are peculiar to the particular installation.
Clinker rings can be avoided by shifting the flamefurther back, thus increasing the clinker tem-perature at the kiln outlet. As a result of this,however, the "stickiness" range of the clinker isshifted towards the cooler inlet. Coatings can thenbe formed on the cooler inlet chute. This is par-ticularly problematic with satellite coolers. Ininstances where this occurs with grate coolers,these coatings can be eliminated by the use of watercooled plates on the inlet chute.
Table 1: 7 r' AND LOCATION OF RINGS AND COATING(according to Opftr, 1974)
type kiln type(s) location temperature ('C)gas charge
coatfng a l l exhaust fan 128/180 -blades
slurry rlng long wet drying zone 150/300 < 100
coatfng dry stage 3 & 4 700/1100 700/800(preheater)
coating Lepol grate walls/roof of 1000/l 100 --hot chamber
coating long dry Inlet chamber lOOO/llOO --
meal ring preheater calcining zone 1100/1400"("%8""middle ring long dry II 41400
wet 1) #I 41400 <1200
kiln charge a l l calclnfng <1400 <1200ball zone
slnter ring a l l beglnnlng of 1400/1600 1250/1350. sinter zone
slnter zone a l l slnter zone 1600/1800 1350/l 450coatfng
clinker rfng a l l end of slnter 800/1600 1200/1400zone
coating grate cooler 600/800 1200entrance
Table 2: GKNPRAL MATERIAL CHARACTERISTICS OF VARIOUS RING TYPES
K
:n
all
NL
DS
w/P
DL
WLDSDL
A L L
A L L
A L L
A L L
Enriched in TextureChbractarBase Material
LocationType
-----Clin-ker
Ne,KInt.Med.
Packing
den8e
d e n e e
pOr0ll*
poKOU8
porou8
deneeI.
porou8
poroun
pcwOU8
prwOU8
PorOU8
'P8rtlcle'8ire
fine
R a wHeal
+Coating EXh8U8t fanBlade8
Slurry ring Drying Lone t(du8t
t t fine
-
t
-
t
t
t
t
--
t-
t
Coating Stage Ji4 fin8
fineCoating Halls/roof ofhot chamber
t
Coating t-
t fineInlet chamber
Calclnfng zone. l
� *
t
t*
flnel
.
Heal ringHiddle ring t
+ 4’
Kiln chargeball
+Calcining zone fine
largeSinter ring Beginning of
8inter xone
I
t
t
tSinter tone largeSinter xonecoating
-
End of sinterLone
Cl lnkerring
Coeting
large
large
-
Grat8 COOl cr
l coating center
lrblt 3 : PROPERTIES ff BUILD-UPS EXAMINED
AlktllSulphulRJtio
Gtnerrl tppttrrnctModlIlIVolrtllt Eltatnts Ttrturt
Poresire (jIltI
S R An LSF Strtngtl Colour
.ocrtlaalrnl
A
A
A
6
c
C
0
E
B
F
HtntrtlogyColour
,f strtrksK20 Bld.lJnlts
fpd
.I - 10
LtytrSwpltI
0.16 1.76 2.71 Yellw rtdlbrwn1st cyc 7.6 I - 1062
66
124
149
339
180
196
103
104
69
1.6
0.36 2.05 2.77
stron9
strong11.4 0.16 24.0 ytllw rtd/brwnInd cyc dtnseporous
dtnstporous
denseportus
VI- 5I - 10
-
Cl- 32- 6
10 - 20
1: : 2:
portsfllltd
portsfllltd
portsfilled
10 - 20
2: : 5:
KCI-200chrvgt 1-5
KC1 cont.chrrgt 2-3
KC1 cont.chrrgt O-5
5 - 10
20 - 30
Iu.KCl cant20 - 30
1.8
1.09
0.85
0.02
2.25 3.44
2.8 2.5
WJk
strong
yellow
allw/irwn-yellow
none
dtrL brown
4.6
1.3
0.09
0.65
2.56
36.0
0.61
lrd cyc" .
Ith c c'Pjpt r
' (Cone.
strong
strong *td/brom
mtdlum brown
wrk brown
0 . 8
0.19
3.6
28.0
23.6
0.67 2.4 1.69
0.38 3.33
0.07 1.46
1164.91 3.01
2.31 3.2
1.70
1.45
2.26
2.6
none
none
blttlgrttn
none
none4.66 2.62 2.36. 31.5
3 . 6
4.0
0.16 strongitllwlrwn
1.59
1.3
157
196 strong none
0.69 3.2 2.13 114 WtJk none
5.69 62 weak none
0.68 75 strong ,rd/broua blrck
User'lpt
" 10.2
1 . 3
4.6
17.6
0.08 1.61
2.5
-i-Kma or: crlcltt,su p atrite, KC1
spur-
minor: s ur-Tltc,Cr tIi
porars IO - 1s
2: : 3:
>l100
:flnnltt.
.
6.4
1.6
6.9
0.19
1.1
0.34
0.27 2.09
1.48
1.65
I4E0
6tnsrporous
dtnstporous
Table 4 : PROPERTIES ff RIMiS EXAMINED
TextureVolrtlla Elements nodull Generrl appearance
AH LSF Strength Colour
hlkrllSulphurRatio
0.44
0.14
Hlnerrlogy.ocrtlonPlant RingTYPL
MUd
Ball
Heal
SR PoreShe (pm)
Bld.Unltsfpd
K20 ma20 SO3
strong
strong d--He or - Sulphrtepurrlte
#(nor - C2S, C4AF,mite. vrrloussulphrto
2- 3
100
100
110 a
100 a
4.1
2.18
0.40
0.16 14.2 2.36
1.40
1.46
(*let,(bitt)
2- 5
50 - 100
50 - 100
150 - 450
50 - 100
yellow/brown
yellow/brown I
110
10
9 2
00
g;; c25, C3A. C4AF 150 - 250
50
0.16
0.12
0.06
0.07
1.56
0.84
1.6
2.32
K
F
Middle
Middle
45 l
37 a 2.13
2 .4
strong
rtrong
strong
strong
0.13
0.71
1.01
0.21
0.01
0.05
Et;; CZS, C3A* C4AF
C3S. C S,spurrl et
C3A, C&Of
200
100 - 150
Ash/Slnter
Ash/Slnter
100 - 200
200
150 - 300
1.01
0.34
0.24
0.03
1.14
1.21
01
7932.5 8
I EP0.20 1.56
Ash/Slnter
Et& $5, C3A, C4Af 200 - 500brow/9wN 2.88 a018.5 a 0.95 0.20 0.56
TABLE 5 : Typical analyses of a middle ringat various depths
sample ring ring ring clinkerinternal middle external
Loss on iqn. 0.47 1.82 0.94 0.37
Si02 23.0 17.8 21.9 21.9
Al203 4.9 5.1 5.5 5.6
Fe203 3.0 2.9 *-. 3.1 3.2
CaO 66.4 70.7 66.8 66.1
M90 # 1.1 1.0 0.95 0.95
so3 0.13 0.07 0.27 0.48
K20 0.16 0.09 0.30 0.35
Na20 0.06 0.06 0.12 0.14
TiO2 0.25 0.23 0.25 0.25
m203 0.02 0.02 0.02 0.02
p205 0.24 0.21 0.20 0.20
Cl' 0.01 0.01 0.01 0.01
Total 99.74 100.36 100.01 99.57
LS 92 122 96 93
SR 2.91 2.23 2.55 2.49
AR 1.63 1.76 1.77 1.75
TABLE 6: Chemistry and.Mineraloqy of a (coal ash) ring
ciln point
depth in ring
chemicalanalysis:
si02u203-203CaOM90K20Na20so3Loss on ign.-
Total
LSS RA Rfree lime
ninerals det.{wt. %)alite
p< and pbelit
liquid phase(aluminate +ferrite)
carbonatespurrite+CaOf
E\belite
texture:
average poresize (esti-mated) p
29.5 32.5
under hotsurf ace
24.65 24.61 21.775.68 5.70 5.484.23 4.29 3.53
61.27 61.92 65.310.49 --0.79 0.640.58 0.34 0.170.36 0 . 0 3 0.200.15 0.27 0.342.61 1.63 2.48
100.0
78.1 79.0 93.72.49 2.46 2.421.34 1.33 1.551.0 4.0 2.7
nJ 30
ry35 - 40
ni 15
Id15
< 5
400 - 800 400 - 800
middle
99.68
d 15
N 55 - 60
N 15
h/ 10
45
near shell fI
100.0
d 4 0
rJ 30
d 15
& 15
II
100 - 300 1
TABLE 7: Chemical composition of core and rim of mealball and the kiln charge composition at thecorrespondrnq zone
Ik i l n b a l l kiln charge
rim core calcininqzone
Loss on iqn.I
3.9 4.3 1 1.9I
Si02 I 20.9 I '-17.2 I 21.2
A1203 I 5.6 I 8 . 0 I 5.7
Fe203 ' 2 . 8 4 . 4 2.7
Ca0 63.0 62.5 62.1
s03 1.9 1.7 2.2
K20 I 2.1 I 1.5 1 2.3'I
Cl' I 0.1 I 0.1 I 0.1I
LSF 94 1 0 4 I 91
SR 2 . 4 1 . 4 1 2.5I
APPEND
IX I
APPENDIX II: CHEMICAL ANALVSIS OF RISER PIPE AND KILN INLET DEPOSITS
MA-Mat. Nr.I
50'393 I 53'550I
PlantI
DI
G
LocatlonI
Rlser Plpe
Loss on Ign. 11.8sio2 9.2A1203Fe 03Ca 6
:*2"49:3
MgO 1 . 2SO3 15.9K2D 3.6Na20 0.98TiOMn2 6 3
0.090.07
; :- 05 0.11 2.7
Total 100.65
:"R 1.61 1.59LSF 1 5 7
10.17.4f*$
46:l
2:::
z50:150.010.095.0
1;*:3:4
5:::
E8.40.190.150.030.052 . 1
252:;'10.6
4:*;0:834.6
: 7.6
it*:10:os0.380.27
0.5712.4
2:39:82.3
27.6
:*:r0:190.160.080.09
99.7 102.82 101.23 98.83
2.47 3.12 2.09 1.481.31 2.13 5.89 0.68196 114 52 95
54’155 1 54’118 53’956
A I I3
Kiln Inlet (OS)
H
KilnInlet (DG)
APPENDIX III: CHEMICAL ANALYSIS OF RINGS FROM,ROTARY SECTION OF KILN
MA-Mat. Nr. 53’952 52'040 52'037 52’178 49’643 45’061 50'524
Plant I K F M 1 L N J
Location 100-l 10m 45m 37m 32.5m 35m 18.3m 1OOm
Loss on ign.SfO2Al203;;a03
I? t.3so3K2DNa20ii02Mn2D3p
10.714.7
ii:;52.30.79
t::0.400.180.060.230.23
0.4723.04.93.0
66.41.10.130.160.060.250.020.240.01
2:::
FL!63:l2.10.770.720.070.310.040.080.05
1.6324.6
45::61.90.790.270.340.03
0.1222.84
35:;63.90.921.071.07
' 0.240.360.150.24
8.1121.34.5
5;::
:.:60:950.280.280.020.080.28
2:::
:*:50:81.13
14.22.180.160.220.040.240.01
Total
CaOfSR .
EF
98.89
2.191.48110
99.74 100.44 99.68 100.25 100.56 99.38
27-h1:63
92
2.73 2.462.32 1.3388 79
El1:8488
2.881.5588
0.622.361.467 8
PHOTOTABLE 1: S.E.M. MICROGRAPHS OF DEPOSITS
1 a)l0J.u
I I REM 84/108
Mud ball in chains
1 b) eY REM 84/506
Compact cyclone 2 deposit
IOU/lc) u REM 841545
KC1 crystals
ld) ,xm , REM 84/69
Spurrite crystals
1 el REM 84/79 1 f) REM 84/72
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
Module 13
Section 12
Rings and Buildups in Cement Kilns
B U R N I N G I S S U E S
The problems caused by rings andbuild-ups in a kiln system always cre-ate turmoil and frequently a loss of
production. Most of these problems can becontrolled if not eliminated.
Figure 1 indicates the major causes ofrings and build-ups. There must be a goodevaluation programme, which includes areview of the literature. When this is accom-plished, there are definitely solutions to theproblems of rings and build-ups in the kiln.Frequently the solution requires forgettingsome preconceived ideas.
This section will not cover all of the ringsand build-ups that can occur, but will
address those most frequently encountered.There are problems associated with theburning of waste fuels which can be attrib-uted to flame position, alkalies, chloridesand sulphur.
Figure 2 shows a basic understanding ofair volume changes attributable to changesin temperature. Our experience indicatesthat many people tend to forget this rela-tion. They comments “I didn’t increase theair flow,” “the flame looks like it is on theload. It wasn’t yesterday; someone musthave moved the burner.”
Figure 2 shows the increase in volumecaused by temperature changes. One cubic
MAJOR CAUSES fig.11 . Overheating2. Slow clinker quench3. Fuel impingement on the burning zone
load4 . Long flame5 . Chlorides6 . Suiphur7 . Potassium8 . Mechanical restrictions
EVALUATION PROGRAMME.1. Sampling2. Care of sample (temperature, air and
moisture considerations)3. Samples which are consistent and
representative4. Documentation of conditions before and
during time of the problem
SOLUTIONS1. Alter raw materials and fuel2. Control internal alkali, sulphur and chloride
cyclea. Install a kiln gas by-pass for preheaterand calciner kilnsb. Do not return as much total dust,especially where precipitator fields dischargeto individual conveyorsc. Determine time cycle for build-upAdjust kiln burner (permit clinker quench,shorten burning zone length, eliminate fuelimpingement on the load, locate burner onkiln center line and slope)
4. Adjust kiln material and gas temperaturep r o f i l e
5. increase kiln rotational speed6. Install kiln internal restrictions such as
dams or orifice rings7. Maintain the secondary air temperature
consistently
foot of air at 100°F weighs about0.071 pounds. The weight of onecubic foot of air seems insignifi-cant, but at each of these plottingthe weight of air is the same(0.071 pounds), only the volumehas changed. 4.4 cubic feet of airat 2000°F still weigh 0.071pounds.
We often hear the question,“Where is the best place to sam-ple the kiln discharge hood pres-sure?” But the real question is“where on the hood does thesample point (or points) give apressure reading that permits rel-ative control?” That is, where arethe conditions today similar towhat they were yesterday? Thenext question is “what is the cor-rect kiln discharge hood pres-sure?” The kiln discharge hoodshould be at a slightly negativepressure to permit observationby instruments or persons with-out undue overheating and dustyconditions. From the standpointsof good housekeeping and main-tenance, the hood pressureshould be slightly negative. Thisvalue should be
inches w.g., -0.01, -0.1, -0.15, etc. Quite pos-sibly the most serious effect on hood pres-
sure sampling over the years has been ourattempt to “bum on the nose.“ All changesin fuel ignition are immediately detected byhood pressure changes-there is no damp-ening effect as there is when the flame isaway from the nose.
Figure 3 shows the different pressureconditions found in the kiln discharge hood.This is why more than one sample point isneeded, with all manifolded together toserve as one sample source. The result is themeasurement of an average pressure.
It is interesting to note the effect highersecondary air temperatures have on the kilndischarge hood pressure. The increase ofsecondary air temperature increases the vol-ume of air as well as the velocity. Thisincrease of velocity tends to drive the sec-ondary air and dust toward the top of thehood. This condition always creates a dust-ing and puffing at the top of the hood overthe kiln, whereas the bottom side of the kilnmay be at slightly negative pressure.
A change in secondary air temperaturecan move the flame position up or down.Certainly, a change of secondary air temper-ature wilt alter the fuel ignition rate, but theconcern in this example is the positioning of
determined by trial rand error for each fig.3 POSITIVE
system. It is alwaysadvisable periodi-
POSITIVE PRESSUR
tally to review theselected set point todetermine if condi-tions have changed.
NEGATIVE
Once the desiredkiln discharge hoodpressure is selected,that is the target,whether it is 0.05
B U R N I N G I S S U E S
secondary air temperaturei s increased. Velocitythrough the cooler throatincreases to 1275 feet perminute. This increase ofvelocity tends to raise theflame path, which usuallycauses the burning zone tocool off and the calcinedmaterial to flush into theburning zone.
These examples showwhy it is more importantto maintain a constant sec-
the flame path. ondary air temperature than to attempt toFigure 4 shows the burner positioned on reach the highest possible temperature.
the kiln centre line and slope. Thisposition has been adjusted duringoperation to compensate for the sec- fig.6
r - - - - - x -ondary air’s tendency to lift theflame path. In this example the intentis to direct the flame tip on the kilncentre line and slope. Figure 4 indi-cates that the average secondary airtemperature is 1000°F. The volume ofsecondary air passing though thefixed throat area has a velocity of 900feet per minute.
The system in figure 5 is identicalto that in figure 4 except that the sec-ondary air temperature has been
clinker and past a thermocouple sensor.Methods for aspirating air from the clinkercooler have proved to be impractical pri-marily because of wear created by theclinker dust. Quite possibly the calciner kilnsystem permits the most accurate measure-ment of combustion air temperature. Thecalciner kiln system aspirates combustionair from the clinker cooler as tertiary air forthe calciner.
In spite of its inaccuracy, the thermocou-ple placed in the clinker cooler throat hasbeen accepted as indicating a usable relativesecondary air temperature for day-to-daykiln operation. This method of detecting sec-ondary air temperature is fine if we remem-
ber thatm It is a relative temperature and
may read much higher because ofradiated heat from the clinker.
n It may increase or decrease,depending upon changes in theclinker cooler bed, without muchreal change in air temperature.Fluctuation of secondary air tem-
perature is one of the major causes ofrings and build-ups. The kiln flameand location must be controlled tomaintain a stable operation. A stablekiln operation should create the pat-tern of coating and a ring formation
reduced to 700°F. The velocity of the sec- Normally, attempts to achieve the maxi- shown in figure 7. This drawing shows onlyondary air through the clinker cooler throat mum secondary air temperature produce a small amount or no coating from the burn-has now been reduced to 715 feet per cyclical operation of the kiln. This promotes ing zone to the kiln discharge end. The ringminute. The flame path has been lowered the production of clinkerand the tip is no longer on the kiln centre burned in a reducing atmos-line and slope, resulting in fuel impinging phere, slow quench of theon the load. The problem of fuel impinge- clinker minerals, dusting in the C ,I ’ment on the load is definitely more pro- kiln discharge hood and kiln ., ‘, .,nounced when the burner is adjusted to turn ring formation.the flame toward the load. Microscopic It is also important to recog- :analyses often indicate that the clinker was nise that the secondary air tem-produced in a reducing atmosphere on this perature recorded by mostdate, whereas the day before this was not plants is a relative temperature.the case. The secondary air temperature
Figure 6 shows what happens when the is usually detected by placing athermocouplesomewhere near the that forms 80-115 feet from the kiln dis-clinker cooler throat area. charge end is in the area where calcination isThe value indicated by this complete and the liquids begin to form. Themethod of sensing not only location of this ring depends upon the burn-measures the air tempera- ing zone length. It is formed because of theture, but it also detects coexistence of calcined material, a smallradiated heat from the amount of liquid, and material still in theclinker and the flame. A solid phase. This creates prime conditionstrue secondary air temper- for build-up. The ring does not adhere to theature is measured by aspi- refractory, is not dense and is, very fragile. Itrating a portion of the set- breaks up and falls out when the kiln tem-ondary air away from the perature is changed by alterations to the cal-
B U R N I N G I S S U E S
cining zone and material preparation. It such as a decrease in sec-may fal l out when f lame length and locat ion ondary air temperature, maychange. crea te the condi t ion where the
This r ing i s regarded as an asse t because f lame t ip i s projected throughi t serves as an or i f ice that increases the gas the load ( f ig 9) . This lengthen-
ing of the flamecauses fuelI I
LONG FLAME impingement onthe load , bu t a l socauses the conical -long flame ringbuild-up shown in figure 8. presence of a nose r ing indicate the presenceWhen this ring is detected, it of slow quench. The nose ring permits acan be broken up and dropped very s low quench of the c l inker because theout by shortening the flame. mater ia l i s pooled when i t passes out of the
_ _ ----.-I- This type of ring can also be burning zone. Quick quench of the clinkerprevented with a short flame minerals must be completed wi thin the ki ln
ve loc i ty a t i t s l oca t ion . Th i s t ends to ho ld with its tip directed on the kiln centre line or it will not be achieved.back and mix aerated material. While the and s lope . Slowly quenched c l inker causes the C?Sring is present kiln operation tends to be sta-ble, with less material flushing into theburning zone. If all conditions remain sta-ble , the r ing remains and ass i s t s opera t ion .I t does no t g row subs t an t i a l l y a s t he s t ab l eoperat ing t ime increases . For several daysof ten the r ing fa l l s out , k i ln opera t ion maybe cyclic and it is difficult to keep the rawload out of the burning zone. We have of tenreviewed kiln operators’ logs and found thisto be a common scenario.
Figure 8 shows the ring caused by a longflame. This ring may also be formed when
Another example of a long flame is to rever t back to C,S and free lime. Furthers low coo l ing causes the C,S finthe beta s ta te or high- tempera-ture form) to change to thegamma state of C,S (a low-temperature form). T h egamma form of C2S is a dustand no longer forms a nodule.
\ This dust is picked up by the
NOSE RING flow of air and carried backKILNDISCHARGE SLOW QUENCH into the kiln where it enters the
--I_--- burning cycle again . The s lowquench cyc le con t inues as long
as the nose ring persists to act as a dam. Thesuspended par t ic les re turn ing wi th combus-t ion a i r a re eas i ly preheated because the sur-face area is maximised. The l iquid availableat the kiln nose permits adherence of thedus t pa r t i c l es , and the bu i ld ing o f the noser ing con t inues .
I- t i e . 1 2SLOWQUENCH
the flame path is directed into the load. In shown in fig 10. In this case the flame tip isthe latter case, the kiln may have experi- at least directed on the kiln slope and paral-enced stable operation with the flame lel to the kiln centre line. There are appar-
ently sufficient liquids avail-ab le to p roduce a s t i cky env i -ronment which promotes thedevelopment of a material bal l .Bal l s which are 6 to 12 inchesin diameter have been foundin the middle of the calciningzone. A few of these ballsgrow to diameters of 6-8 feet .The larger bal ls look alarming
di rec ted toward the load , and th i s loca t ion when they are f i r s t seen pass ing through themay be sat isfactory as long as the f lame t ip burning zone. Burning with a shorter f lameis not on the load. However , when the f lame length prevents additional balls formingtip is directed into the load, any change, unless they a re caused by a h igh concentra-
tion of alkalies, sulphur, andchlorine.
fig.10
i P----KILNKILNDISCHARGE
The nose ring (fig 11) hasbeen described as an “ashring.” Some ki lns operate wi tha nose ring most of the time.This tends to restrict clinkerdischarge from the kiln.Microscopic evaluations ofclinker produced during the
Figure 12 shows an example of a snow-man on the clinker cooler back wall. Somesnowmen grow tall enough to reach theburner pipe. Generally, the larger the kiln,the larger the snowman. Depending uponthe ins ta l la t ion procedure of refractory overdead grates, some kiln systems form snow-men on the c l inker cooler s ide wal l near thethroat . The snowman bui ld-up i s caused bythe same problem that promotes the noser ing bu i ld -up - tha t i s , s low quench of thecl inker .
Microscopic evalua t ion of c l inker showswhether the mater ia l was s lowly or quicklyquenched and whether C,S changed fromthe beta to the gamma s ta te . Both the nosering problem and the snowman build-upcan be eliminated by adjusting the kilnburning operation so that the clinker isquickly quenched within the kiln.
B U R N I N G I S S U E S
We have learned to live with a dusty kiln temperature increased from 2600°F to level which removes a similar amount fromdischarge hood, especially in larger kilns. 2750°F and NOx fell from 750 ppm to 350 the cycle. If the long wet and dry kilns useThe old small wet-process kilns were sel- ppm. The clinker went from slowly an electrostatic precipitator, the dust col-dom dusty because the fuel consumption quenched to quickly quenched. The clinker lected in the final fields can be wasted as
HIGH SULPHUR RING T H I C K N E S S C A N B E 1
KICNDISCHARGE
cooler snowmenwere eliminated,the kiln dischargehood cleared andwe could see theflame and burn-ing zone. In addi-tion the 28-dayc o m p r e s s i v es t r e n g t h sincreased by 600psi over a 90 dayperiod withoutany increase offineness.
high alkali, sulphur, and chloride material.The electrostatic precipitator works well
as a kiln gas bypass system for the long wetand dry kiln systems. Since the solidifiedalkali, sulphur, and chloride particles arevery small, they are concentrated in the finalfield of the precipitator, and are easily sepa-rated and removed from the system.
Figure 14 shows some areas in the sus-pension preheater where problem build-upsoften occur. As we proceed up the preheaterin the direction of the kiln gas flow, the firstproblem area is at the kiln feed shelf. Thisproblem on a preheater kiln is either causedby leakage of ambient air into the system or
Figure 13 displays a ring formation by operating with a high level of carbonwas high and we could not gain quick which occurs in the calcining zone or the monoxide in the exit gas. Ambient air leak-enough ignition to burn on the nose. Thispromoted the quick quench of clinkerwithin the kiln. We also found that the oldwet kiln produced the most reactive clinker,which permitted a lower fineness for similarcompressive strength levels.
Our most recent experience of puttingthis flame technology into practice was witha large wet kiln. It was necessary to removelarge snowmen from the clinker back wall.These snowmen were giants, lo-12 feet highand 6-8 feet in diameter at the bottom. Thekiln discharge hood was so dusty that wecould not see the nose of the kiln. The noserefractory had to br replaced every sixmonths and the nose castings every 12months. The kiln burner was adjusted to
area where thegas temperature issufficiently low topermit condensa-tion of sulphurand chloride com-pounds. This ringis a part of thealkali, sulphur,a n d chloridecycle. All kilnshave a variety ofrings in this area:some consist of asmall amount ofPU”kY coating.With larger rings
shorten the flame: this reduced the burning (fig 13) the kiln has to be shutdown to phys-zone by about 45 per cent. The burning zone ically remove the build-up. The elimination
of the cause nor-mally requires a
fig.14 fuel change, suchas a lower sulphurfuel, a n d thereturn of less kiln
VELOCITY dust. If a micro-scopic evaluationof the clinker indi-cates productionin a
HATES ANi
reducing
T E M P E R A T U R Eatmosphere, theburner should be
BYPASS QUENCH Al RIN RISER adjusted to elimi-
nated fuelimpingement onthe load. This willpermit a higherclinker sulphur
K I L N G A SBYPASS
fig.15
L 19OO’F T O 21OO’F
age causes a localised condensation of alkali,sulphur and chloride compounds. Thesechemicals are vaporised in the burning zoneand exit as a kiln gas until temperature con-ditions are sufficiently low (about 1800°F) tocause condensation to the liquid state.Normally, the preheater kiln exit gas tem-perature is above the condensation point.When ambient air leaks into the kiln feedend housing there is a localised cooling ofthe kiln gas at the leakage source that resultsin build-up at that point. A different type ofcalciner kiln system build-up at the feedshelf and feed end housing walls can also becaused by leakage air. This build-up iscaused when the kiln feed is nearly calcinedand there are C,AF liquids present.However, if the gas dust concentration issufficiently high, the liquid will adhere tothe dust particle rather than to the surface ofthe wall, thereby preventing a build-up.
B U R N I N G I S S U E S
AP = 2.0' KI LNthe kiln bypass
75O*F T O ilOO°F I i - - + - -induced draught fan.
GAS Alkali, sulphure
!
BYPASS and chloride com--0.5. TO -1.5” pounds create no
-2.5" TO -3.5” o
QUENCH CHAMBER m -Ibuild-up problems ifthey exist in either
I ‘.
7
7-J
em -1900’F T O 2100’Fthe gaseous state orthe solid state.
QUENCH AIR ’
i
/However, if theyexist in the liquidstate, they behave
also ensure that the
quench air exits to
fig.16 like water on dust.The secret to efficientkiln gas bypass sys-
This situation can be artificially dupli- tern operation is taking a portion of the kilncated by the introduction of dust from the exit gas at plus 1900°F and instantaneouslyStage III cyclone material discharge and/or quenching it to about 750°F. This permitscreating a rough feed shelf surface which the alkali, sulphur and chloride compoundscauses the a splashing of the feed out intothe gas stream. Dust re-entrained in the kilnexit gas by a rough feed shelf surface willincrease the dust lost through a kiln gasbypass system, so the feed shelf must have asmooth surface when running a kiln gas by-pass system.
Figure 15 shows a build-up above thekiln gas bypass take-off and within thequench chamber. The build-up in the kilnriser above the kiln gas bypass take-off iscaused by the leakage of quench air fromthe quench chamber. Proper sizing of thebypass quench chamber inlet can ensurethat quench air does not enter the riser duct.
The example in fig 16 shows the parame-ters used for design and adjustment of thequench chamber inlet. A two-inch pressureloss through the quench chamber inlet will
to pass from the gaseous state directly to thesolid state without passing through the liq-uid state. Some designers and operatorsquench to higher temperature levels, i.e.900°F to 1100°F. Our experience has foundmore potential for build-ups in the quenchchamber at these higher temperatures.
The kiln gas bypass system appears to workbest when the quench chamber and kiln riserduct take-off are placed above the kiln. As thegas and dust exit the kiln, the dust is thrownagainst the feed shelf while the gas is turnedupward. This separates dust particles from thekiln exit gas stream. The cleaned gas tends topass on the kiln side of the riser duct for a shorttime. Figure 17 shows the desired quenchchamber position and fig 18 indicates thedesired operating parameters for a kiln gasbypass quench chamber. In our experience aquench chamber operated with these parameters will not product any build-ups, and will
NCH CHAMBER
GAS AND DUST
DJST -GAS ---c
operate with no dust in the bottom of thechamber.
Kiln gas bypass dust collector material con-tains 0.520 per cent of clinker, 20-25 per centSo,, and 4.5-5.0 per cent K20. If the percentageof sulphur as SO3 is less, for example 16 percent, the bypass system is taking too muchdust from the kiln riser, etc.
There are always answers to problemswith rings and build-ups. The solution isusually found when the attitude of theoperator is that “we cannot continue to livewith this problem.” JI
This paper was first presented by the author,Floyd C Hamilton, of Hamilton Technical Serviceslnc, Roanoke, Virginia, for the National LimeAssociation meeting, St Louis, Missouri, UnitedStates, October 1997.
Blue Circle Cement
PROCESS ENGINEERING TRAININGPROGRAM
HBM PROCESS ENGINEERSCONFERENCE
• Minimization of Volatile Cycles
MINIMISATION OF VOLATILE CYCLES
1 . SUMMARY
Concentration of minor components within kiln systems due to volatile cycles can lead tosignificant operational problems on all types of process, with consequent loss of output. Aportion of some of these volatile materials is also lost to the atmosphere, and minimisation of this“leakage” is also increasingly becoming an environmental concern. understanding of the factorsthat effect the magnitude of these cycles is an essential part of improved kiln control leading toeffective control of the cycles. Successful implementation requires co-operation between chemist,process engineer, mechanical engineer and operators.
2. INTRODUCTION
A limited number of minor components in the raw mix and/or fuel can become highlyconcentrated within the cement kiln system and then create operational problems. The minorcomponents that are generally considered to be involved in major volatile cycles are the chloride.alkali (Sodium and Potassium) and sulphur species - although other elements do also becomeinvolved in cycles to a much lesser degree (such as F l V, As, Pb, Tl Cd, Hg and Zn) they havenot been identified as causing operational problems and so will not be considered at this time.These substances are present in the raw materials in low proportions in a variety of forms, but arelikely to evaporate or decompose under the temperature regimes found in the burning zone. Oncethis happens they become associated with the gas stream and cool as this losses its heat to thematerial bed, until they either condense or react to form compounds that will condense. At thispoint they are present in the gas stream as potentially sticky liquids and will adhere to any surfacewith which contact is made; this can be a particle surface or a vessel side wall. Once the liquidhas condensed on to a particle this can still stick to any wail with which contact is made until thetemperature drops to a sufficiently low level for the liquid to solidify. In the suspension preheaterand Lepoi processes the temperatures at which the potential compounds are liquid coincide withthose found close to the kiln hearth and lower preheater stages (SP kiln) or above calciner (Lepolkiln), and this leads to material building up on the walls in these areas, or to ring formation at thevery back of the kiln. In the older long chained kilns, excessive volatile cycles can contribute toring formation. In either situation, at best this reduces the duct or kiln dimensions and so causesincreased pressure drop and - probably - extra dust generation, whilst at worst it reduces output,increases kiln instability, and causes blockages to develop in the preheater system: the end resultbeing significant kiln down time.
In general, in the more thermally efficient processes (precalciner, suspension preheater and Lepol)most of the volatiles will condense in the preheater and only a small fraction will condense on theprecipitator dust or escape up the stack. In contrast in the less thermally efficient processes (wetand long dry) a higher proportion of the volatiles will pass through the kiln system and condenseon the precipitator - or bag house - dust or escape up the stack. Commonly where volatilescondense onto a dust the finer dust fraction will develop a higher concentration of the volatilecomponent, due to the higher surface area of the finer dust.
Where a component is partially volatilised in the burning zone and then partially recombines intothe material stream within the kiln/preheater system it is possibie for a large amount of thecomponent to continuously recycle around the kiln system. This is called an internal cycle.Where some of the component is collected with a dust stream externally to the kiln system andthen returned to the kiln, this is referred to as an external cycle.
3. GENERAL REVIEW OF THE PROPERTIES OF THE MAJOR VOLATILECOMPONENTS
3.1 Chlor ides
Chlorides are derived from the raw materials and the kiln fuel. The high voiatilities of thesecompounds, together with the high collection efficiency of the cyclone preheater systems, will leadto the development of a greatly enhanced cycle. The chlorides have a high affinity for the alkaliesin general and potassium in particular. This property together with the high volatility has been
used in kilns (commonly on rhe wet process, occasionally on the SP process) to control clinkerK2O levels by addition of CaCl2 to the raw mix or fuel, which leads to loss of KCl with the kilnbleed or the exhaust gas from the kiln system. In the suspension preheater, the volatilised materialis recaptured within the system unless a bleed is utilised between the kiln and riser duct. It isgenerally considered that no more than 3% of the chloride passing- from the preheater to the kilnwill leave the system with the clinker. Although considerably higher levels have been noted inindividual samples of clinker, this is probably due to a “push” of kiln feed, or a semi-flush situationas thermodynamic considerations indicate that no chloride should pass through the burning zone.On many SP kiln systems some degree of preheater cleaning is necessary on a regular basis andthis may help to control the chloride cycle by forcing the kiln conditions into a situation whichpermits a brief increase in clinker chloride level (i.e. reduced material temperature, increasedmaterial loading and flux level).
Small amounts of chlorides will also leave the preheater system with the waste gas stream.Taking the total loss of chloride from the system as between 2 and 5 % of the feed to the burningzone, it would then be expected that a circulating load of 20 to 50 times the total chloride inputcould develop in a system without a kiln gas bleed.
No reports of low temperature chloride volatilisation within the preheater have been identified.
3.2 Alkalies
The major source of alkalies will be the raw mix; notably the clay component, although minorquantities can arise from the fuels The initial free alkalies will behave in one of three ways:
1) Remain in the material being processed and become incorporated in the clinkerconstituents that are being formed. This happens to Na2O to a greater degree than K2O
2) Be converted into different compounds - chlorides, sulphates, carbonates, hydroxidesby reaction with ofner constituents of the raw mix.
3) Diffuse to the surface of the process material and volatilise.
In its initial state, K2O begins to volatilise over a wide range of temperature, depending on theform of clay in which it was incorporated but irrespective of source, it would be expected to havevolatilised almost completely at burning zone temperatures, although some may have been at leastpartially stabilised by conversion to the less volatile sulphate form within the material bed. Oncevolatilised it will react to form chlorides and sulphate - chlorides preferentially - at the rear of thekiln. These will then deposit on dust particles. Initiallv Na2O is less volatile than K2O due to itshigher bond energy and so a greater proportion of the kiln feed Na2O would be expected to passthrough the burning zone in clinker without participating in the volatile cycles. Volatilised Na2Owill react with SO2 and SO, to form sulphates towards the rear of the kiln and with chloride wherethis species is present in excess of K2O Where alkali is present in excess of chloride and sulphatealkali carbonates will be formed Each of these al “-=smmthe surface of dust particles in the cooler zone of the kiln ad lower preheater stages and will enterthe volatile cycles as the dust is separated out in the cyclones. Direct contact onto kiln orpreheater surfaces may lead to the development of build-up, The compounds will then re-enterthe kiln where the degree of volatilisation will depend on the species and the kiln conditions.Volatility decreases from chloride to carbonate to sulphate and, hence, sulphates are more likelyto pass through the burning zone. Nevertheless, the likely range of burning zone temperaturescover the thermal area in which alkali volatilities are likely to increase significantly with risingtemperature. In general, precalciner kilns have significantly lower burning zone temperature thanare common in other processes and, hence, alkali sulphate volatilisation in particular is lower inprecalciners than in other processes.
3 . 3 Sulphur
Sulphur can enter the system in a number of forms from either fuels or raw materials. A limitedamount may evaporate in the upper preheater stages and escape from the system in the exhaustgases. In general, SO, and SO, can form in the high temperature areas and be transferred to thegas phase. In the cooler areas of the kiln back-end and preheater system sulphates will form andre-enter the material stream. preferentially alkali sulphates will be produced with excess sulphatecombining with free lime or calcium carbonate an$li@ru&&5li~-i5Xailablein~e~~.--~~~r-‘l-----‘t’:----~~a~~~~~~~~~~~~~, so
restricting the formation of sulphates. In this situation loss of sulphur oxides by way of the stackmay increase but where the gas stream passes through the raw mill the majority of the sulphuroxides would be expected to react with the high active surface calcium compounds which areproduced in the milling process. This will then return to the kiln in the raw mix as part of anexternal cycle.
The high boiling points of the alkali sulphates would indicate that relatively low levels ofvolatilisation would be expected. However, dissociation may occur, particularly under thereducing conditions which can exist to some degree within the burning zone. Calcium sulphatealso has a high boiling point but is even more susceptible to dissociation, so a higher recirculationof sulphate from this compound would be expected. As CaSO4 cannot recycle as a compound,the lime from this compound remains in clinker as free lime - making burning more difficult -whilst SO, is carried in the gas stream towards the kiln back-end where it reacts to form alkali orcalcium sulphate.
4. CONTROL OF VOLATILE CYCLES
As indicated earlier the major species involved in volatile cycles are chlorides, alkali and sulphurbased components. As the development of a volatile cycle depends on the evaporation ordissociation and condensation of a range of compounds the meiting boiling and dissociationtemperatures of these compounds will be of major significance, whilst volatility characteristics willalso be of importance. Boiling and melting point data is presented in figure 1, and volatility datain figure 2. As chemical analysis gives details of the volatile components in the feed materials ofin material from within the system in terms of the primary oxides or elemental forms - IWO, K20,SO3 and Cl - the volatilities are normally expressed in the same terms. and the ranges of volatilityfor each that are commonly found within the cement kiln are given in figure 3. These can beconsidered to be the primary volatilities for these components, and in each case the tabulatedfigures show a wide range of volatilities. This doesn’t help to extend our potential understandingof what is happening within the kiln.
The volatiles however will be present in the material bed in the kiln as compounds for each ofwhich the volatility will depend on physical characteristics such as those set out in figures 1 and2. As indicated in section 3 there will be an order of priority (ease) with which these compoundswill form. Therefore it is possible to study the development of a volatile cycle in terms of thephysical properties of these compounds. The specific volatilities that have been found for eachof the compounds that are likely to form are set out in figure 4. This shows for instance, thatalkali in combination with chloride is more likely to develop a cycle than that combined withsulphate. In the same way, sulphate combined with calcium is more likely to volatilise than thatpresent in an alkali form.
Where volatiles are present in the raw materials some degree of cycle is bound to develop.However, the overall cycles can be governed to a degree by optimising the relative proportionsof each volatile component to maximise the potential for the formation of those compounds withthe lower specific volatilities. The prime control of the volatile component cycle is performed inthe design stage of a works project through the selection of raw materials and fuels in order tooptimise the relative and absolute levels of the potentially volatiie components and, wherenecessary, the inclusion of a bleed system. However, whenever changes are made to a sourcingof raw materials (including fuels) the potential affection in the volatile balance needs to beconsidered.
Where processing conditions are kept steady, the cycles will continue to develop until equilibriaare reached, at which time the total amounts of volatile entering the system will be balances bythe quantities leaving the system.
The degree of volatiisation and the rates at which the equilibrium are established will depend on:
(a) The species, their chemical forms and concentrations.
(b) The volume of gases.
(c) The intimacy of contact between gas and solid.
(d)
(e)
(f)
(g)
(h)
(i)
(j)
The vapour pressures of the salts.
Possibility of dissociation or further reaction.
Rate of diffusion to and from solid/gas interfaces.
Degree of saturation of gas.
Kiln atmosphere.
Kiln temperatures.
Time/temperature profile of material within the kiln.
Most of these factors are to some degree inter-related and so in normal operation the onlymethods available to control the degree of volatilisation and eventual concentrations in clinker andwithin the kiln system will be the kiln internal atmosphere and temperature, and the proportionof gas bleed from the kiln exit or material bleed from the system.
As indicated above, it should be possible to modify the volatile cycle by variation of the kilninternal atmosphere (oxygen level) and burning zone temperature. In the late 1980’s a series ofkiln trials were conducted at Hope Works to investigate the effect of these kiln conditions (BZTand BEO,) on the volatile cycles. This study covers the situations of significant chloride, alkali,and sulphate inputs. The major conclusions were:-
1 . The chloride cycle is 20 to 30 times the total chloride input and increases slightly withincreasing temperature, although this may be due to improved kiln stability at highertemperatures. The chloride cycle is not modified by wide changes to kiln atmosphere(Figure 5).
2 . Chloride in the cycle combines with aetassiu~availahle, However, at lowtemperatures - equivalent to NOx Eve1.s‘ om p$ii - some sodium is alsoinvolved.
3. The chloride cycle is a low temperature cycle and cannot be significantly modified byvat-ration or rum conanions.
4. The total potassium cycle is approximately 3 times the input level (Figure 6), howeverabout two thirds of this is present in Stage IV in conjunction with chloride and so cannotbe controlled except by incorporation of a bleed system.
5 . About one third of the potassium in Stage IV is either f& based on its first passagethrough the preheater or derived from a potassium sulphate based cycle. This cycle ratiovaries from 1.05 (minimal recycle) at 800 ppm kiln NOx level to 1.25 at 1,400 ppm NOx(25% recycle). This portion can be controlled by operation at low temperatures (Figure7).
6.
7.
8.
9 .
10.
11.
12.
13.
14.
15.
The sodium cycle level varies between 1.2 and 2.0 times that in the raw meal over thetemperature range examined.
At low temperatures some sodium becomes involved in the low temperature chloride cycleand this boosts the sodium cycle by about 10%.
The majority of the sodium in the system is involved in a sodium sulphate based cycle.This is strongiy temperature dependent, and the rate of increase also appears to beincreasmg with temperature. Over the temperature range investigated the recycle rosefrom 1.35 times the level in the feed at low temperatures to 2.0 times at high NOx levels(Figure 8).
The total sulphur cycle is temperature dependent and rises from 1.6 to 2.6 times that ofthe input over the temperature range investigated (Figure 9). Low oxygen levels increasethe suiphur cycle.
The alkali sulphate cycle has already been summarised in points 6 and 9 and makes upabout 35% of the total sulphate in Stage IV material. These cyclic levels can be seen tobe lower than the total suiphur cycle levels (Figures 7, 8 and 9).
The calcium sulphate recycle is strongiv temoerature dependent. The quantity of SO, as%&(ii$L~V rises from^-“aoout 2.5 times tne level in the feed at low NOx levels to 4times at high (1,450 ppm) NOx levels (Figure 10).
The calcium suiphate cycle is also increased by a move into a reducing kiln atmosphere.At about 1,200 ppm NOx the level of SO, as CaSO4 increased from 3.1 under oxidisingconditions to 5.5 times the feed levei under reducing conditions (Figure 10).
For potassium and sodium there are indications of a slow but steady increase in losses ofthese components from the preheater system as temperatures increase. This may becomepart of an external cycle or may be lost to atmosphere. This could be established by alonger term study of the levels of these components in the precipitator and stack dusts.
Sulphur is in overall balance within the system below NOx levels of 1,200 to 1,300 ppm,but above this level the loss increases sharply with firing temperature. Again this maybecome part of an external cycle or may be lost from the system to the atmosphere,however in this exercise no precipitator or stack dust samples were collected or SO2emission measurements made so this cannot be confirmed.
When the kiln atmosphere moves into reducing conditions the losses of alkalies andsulphur from the kiln system to the atmosphere increase sharply.
Overall the results show that the chloride cycle and its associated alkali cycle cannot becontrolled by process conditions. Cycles of alkali present in the form of alkali sulphate can becontrolled and minimised by careful control of the burning zone to the lowest practicaltemperature. Calcium sulphate based cycles can also be minimised by burning to lowtemperatures, but in this case careful control of the kiln atmosphere {back end 02 level) is alsonecessary to ensure that the on-set off reducing conditions is not possible.
While these tests were conducted on a suspension preheater kiln, the critical area is the burningzone and so the general results will be equally applicable to other processes.
The susceptibility of calcium sulphate to increased volatilisation under even borderline reducingconditions also emphasises the potential for the sulphate cycle to be affected by the condition ofthe firing system, by the type of fuel, and by cooler operation. Low secondary air temperature,a low volatile fuel, poor coal drying, or low momentum in the firing pipe are likely to promoteslow initial combustion, in which case significant combustion is likely to continue to occur oncethe jet has fully expanded. This may give reducing conditions immediately above the material bedand encourage sulphate volatilisation. Where this is possible it is recommended that the firingpipe is aiigned along the axis of the kiln in order to ensure the maximum kiln length is availablefor jet expansion. A “cool” flame is also likely to produce a long burning zone which will holdthe potentially volatile materials for a longer time period within the temperature range at whichvolatilisation could occur; this will also promote higher degrees of volatilisation.
5 . CONCLUSIONS
From a Process Engineer’s point of view, the easiest way to minimise kiln volatile cycles is topush the problem to the Works Chemist and expect the raw materials to be selected to give theminimum practical inputs of potentially volatile materials. This also requires the levels that doexist in the raw materials to be balanced to give the maximum opportunity for the formation ofcompounds with relatively low specific volatilities.
The quantities of material recirculating can also be controlled by the selective removal of a dustfraction from the process. Examples of this are the selective dumping of the finest precipitatordust fraction on the wet process at Ravena, and the dumping of Lepoi cyclone dust at Cookstown.
The magnitude of the volatile cycles can also be reduced by the careful control of kiln conditions.In general volatile cycles will increase slowly with increasing burning zone temperature or length.There will also be a major increase in sulphate cycle if reducing conditions develop close to thematerial bed. This increase will start to occur well before a significant increase in kiln backendCO level becomes apparent. This emphasises the need to possess optimised fuel preparation andfiring systems and an efficient clinker cooler.