mobile radio propagation - bhagalpur college of engineering
TRANSCRIPT
![Page 1: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/1.jpg)
Mobile Radio Propagation
![Page 2: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/2.jpg)
Contents Free space propagation
Basic Propagation modelso Reflection
o Diffraction
o Scattering
Path Loss and Shadowing Models
![Page 3: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/3.jpg)
Wave Propagation Radio, microwave, infrared and visible light portions of the spectrum can all be used to transmit information
o By modulating the amplitude, frequency, or phase of the waves.
The amount of information a wireless channel can carry is related to its bandwidth
Wavelength dictates the optimum size of the receiving antenna
![Page 4: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/4.jpg)
Characteristics of Radio Waves Easy to generate
Can travel long distances
Can penetrate buildings
Used for both indoor and outdoor communication
Can be narrowly focused at high frequencies (greater than 100MHz) using parabolic antennas (like satellite dishes)
Subject to interference from other radio wave sources
![Page 5: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/5.jpg)
Characteristics of Radio Waves (cont.)Properties of radio waves are frequency dependent
At low frequencies, they can pass through obstacles , but the power falls off sharply with increase in distance from the source
At high frequencies, they tend to travel in straight lines and bounce of obstacles (they can also be
absorbed by rain)LOS path
Reflected Wave
![Page 6: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/6.jpg)
Communication ChannelsWired Channel
o Stationary
o Predictable
Wireless channel
o Random
o Typical to analyze
o Susceptible to noise, interference, other time varying channel impairments
![Page 7: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/7.jpg)
Channel models for Wireless Communication Physical models: Considers exact profile of the propagation environment.
o Modes of propagation considered: Free-space or LOS, reflection, and diffraction.
Statistical models: Takes an empirical approach.
o The model is developed on measuring propagation characteristics in a variety of environments. They are easy to describe and use than physical models.
![Page 8: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/8.jpg)
Need for Propagation modelsPropagations models can be used to determine
Coverage area of a transmitter
Transmit power requirement
Battery lifetime
Modulation and coding schemes required to improve the channel quality
Maximum achievable channel capacity of the system
![Page 9: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/9.jpg)
Propagation models Large-scale propagation models
o Characterize signal strength for large T-R separation (several hundreds or thousands of meters)
o Compute local average received power by averaging signal measurements over a track of 5 to 40
o Received signal decrease gradually
o Useful for estimating the coverage area of transmitters
Small-scale propagation models
o Characterize rapid fluctuations in the received signal strength over very short travel distances (a few wavelengths)
o Signal is the sum of many contributors coming from different directions. Thus phases of received signals are random and the sum behave like a noise (Rayleigh fading)
o Received power may vary by as much as 3 or 4 orders of magnitude (30 or 40 dB)
![Page 10: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/10.jpg)
Small-Scale and Large-Scale Fading
![Page 11: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/11.jpg)
Free-Space Propagation Model Predict the received signal strength when transmitter and receiver have clear, unobstructed LOS path between them.
o Ex: Satellite communication system, microwave LOS system
The received power decays as a function of T-R separation raised to some power.
Free space power received by a receiver antenna is given by Friis free-space equation
ππ(π) = (ππ‘πΊπ‘πΊππ2) / ((4π)2π2πΏ)
oPt is transmitted power
oGt, Gr is the Tx, Rx antenna gain
(dimensionless quantity)
oL is system loss factor not related to propagation (πΏ β₯ 1). L = 1 indicates no loss in system hardware (we consider L = 1 in our calculations)
o Pr(d) is the received power
o d is T-R separation distance in meters
o is wavelength in meters
![Page 12: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/12.jpg)
Free-Space Propagation Model (cont.) The gain of an antenna G is related to its affective aperture Ae by G = 4Ae /
2 where
o Ae is related to the physical size of the antenna
o is related to the carrier frequency ( = c/f = 2c / c ) where
Isotropic radiator generally considered an reference antenna in wireless systems; radiates power with unit gain uniformly in all directions.
Effective isotropic radiated power (EIRP) is the amount of power that a theoretical isotropic antenna emits to produce peak power density in the direction of maximum antenna gain.
EIRP = PtGt
Antenna gains are given in units of dBi (dB gain with respect to an isotropic antenna)
o f is carrier frequency in Hertz o c is speed of light in meters/sec
o c is carrier frequency in radians per second
![Page 13: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/13.jpg)
What is Decibel (dB)A logarithmic unit used to describe a ratio between two values of a physical quantity (usually measured in units of power or intensity)
oThe ratio of two values π1 and π2 in dB is
10 log (π1/π2) dB
oExample: π1 = 100π and π2 = 1π
The ratio is 10 log(100/1) = ππ π π©
dB unit is generally used to describe ratios of numbers with modest size.
![Page 14: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/14.jpg)
dBm Indicates power ratio in dB with 1mW as the reference power
Example: Transmit power = 100π in dBm is
Transmit power (dBm) = 10 log(100π / 1 ππ)
= 10 log(100,000)
= 50 ππ΅π
Similarly
1 mW = 0 dBm 1 W = 30 dBm 10 W = 40 dBm
100 W = 50 dBm 106 W = 90 dBm
![Page 15: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/15.jpg)
dBW Indicates power ratio in dB with 1π as the reference power level.
Example: Transmit power = 100π in dBW is
Transmit power (ππ΅π) = 10 log(100π / 1π)
= 10 log 100
= 20 ππ΅π
Similarly
1 mW = -30 dBm 1 W = 0 dBm 10 W = 10 dBm
100 W = 20 dBm 106 W = 60 dBm
![Page 16: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/16.jpg)
Free-Space Path Loss Path loss is defined as the difference (in dB) between the effective transmitted power and the received power
Free-space path loss is defined as the path loss of the free-space model
ππΏ(ππ΅) = 10 πππ(ππ‘/ππ) = β10 πππ[(πΊπ‘πΊππ2)/(4π)2π2]
Friis equation holds when distance π is in the far-field of the transmitting antenna
The far-field or Fraunhofer region of a transmitting antenna is defined as the region beyond the far-field distance ππ given by: o ππ = 2π·2/π , π· is the largest physical dimension of the antenna
oAdditionally ππ >> π· πππ ππ >> π
![Page 17: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/17.jpg)
Reference Distance, π0 Friis free space eq. does not hold for π = 0 Received power reference point, π0 is used
ππ β€ π0 β€ ππ0 should be smaller than any practical distance a mobile system uses
The power received in free space at a distance greater than d0 is
Pr(π) = Pr(π0)(π0/π)π where ππ β€ π0 β€ π
Reference distance d0 for practical systems: o For frequncies in the range 1 to 2 GHz
1 m in indoor environments
100 m to 1 km in outdoor environments
![Page 18: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/18.jpg)
Radio propagation mechanisms
Source: Radio Frequency and Wireless Communications - Scientific Figure on Research Gate
![Page 19: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/19.jpg)
Source: https://physicsweekly.weebly.com/uploads/2/5/8/4/25849299/6320607.jpg?332
![Page 20: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/20.jpg)
Reflection Reflection occurs when wave impinges upon an obstruction much larger in size compared to the wavelength of the signalo Example: reflections from earth and buildings
Reflected waveform may interfere with the original signal constructively or destructively
![Page 21: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/21.jpg)
Reflection (cont.) When a radio wave propagating in one medium impinges upon another medium having different electrical properties, the wave is partially reflected and partially transmitted
oPerfect dielectric:
Part of the energy is transmitted into the second medium and part of the energy is reflected back into the first medium
no loss of energy in absorption
oPerfect conductor:
All incident energy is reflected back into the first medium
No loss of energy.
The fraction that is reflected is described by the Fresnel equation and is dependent upon the incoming light's polarization and angle of incidence.
![Page 22: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/22.jpg)
Reflection (cont.) EM waves are transmitted in two orthogonal dimensions, referred to as polarizations. Two commonly used orthogonal sets of polarizations are
o Horizontal and Vertical polarization
Vertical polarization is commonly used in terrestrial mobile radio communication. In VHF band, vertical polarization produces a higher field strength near the ground. Also, mobile antennas for vertical polarization are more robust and convenient to implement.
o Left-hand and right-hand circular polarization
Often used in satellite communication. Can be used together for well-designed communication links to double the transmission capacity in a given frequency band.
![Page 23: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/23.jpg)
Ground Reflection (Two-Ray) ModelIn a mobile radio channel, a single direct path between the BS and a mobile is seldom the only physical means for propagation and the Free space propagation model is inaccurate in most cases when used alone. Two-ray model is
Based on geometric optics and it considers both the direct path and a ground reflected propagation path
Reasonably accurate for predicting the large scale signal strength over distances of several kilometers for mobile radio systems that use tall towers.
![Page 24: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/24.jpg)
Ground Reflection Model (cont.) The total received E-field, ETOT
is a result of the direct LOS component πΈπΏππ and the ground reflected component πΈπ
πΈπππ =πΈπΏππ + πΈπ
![Page 25: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/25.jpg)
Ground Reflection Model (cont.) Using the method of images, path difference between LOS and ground reflected path can be calculated.
For π β« βπ‘ + βπ, path difference Ξ is
Ξ = πβ²β² β πβ² β2βπ‘βππ
Phase difference πβ between the two E-field components and the time delay between arrival of the two components is
πβ =2πβ
πβ4πβπ‘βπππ
![Page 26: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/26.jpg)
Ground Reflection Model (cont.)
For large distance π β« βπ‘βπ
ππ = ππ‘πΊπ‘πΊπβπ‘2βπ
2
π4
The received power falls off with distance raised to the fourth power, or at a rate of 40 dB/decade
This is much more rapid path loss than expected due to free space
![Page 27: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/27.jpg)
Diffraction Diffraction occurs when radio wave is obstructed by an impenetrable body or a surface with sharp irregularities (edges)
Due to bending of radio waves it enables communication between devices with no line-of-sight path
![Page 28: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/28.jpg)
Diffraction (cont.) Secondary waves are present throughout the space including the space behind the obstacle due to bending of waves around the obstacle.
Enables communication even when a line of sight path does not exist between transmitter and receiver.
At high frequencies, diffraction depends on the geometry of the object, as well as the amplitude, phase and polarization of the incident wave at the point of diffraction
![Page 29: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/29.jpg)
DiffractionHuygensβ Principal
All points on a wavefront can be considered as point sources for
producing secondary wavelets
Secondary wavelets combine to produce new wavefront in the
direction of propagation
Diffraction arises from propagation of secondary wavefront into
shadowed area
Field strength of diffracted wave in shadow region = electric field
components of all secondary wavelets in the space around the obstacle
![Page 30: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/30.jpg)
Diffraction (cont.) Consider a transmitter-receiver pair in
free space
Obstacle of effective height h with
infinite width is placed between Tx and
Rx o distance from transmitter = d1
o distance from receiver = d2
LOS distance between transmitter & receiver is π = π1 + π2
![Page 31: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/31.jpg)
Diffraction (cont.) Excess Path Length is the difference between the direct and the diffracted path Ξ = Ξπ β (π1+ π2), where Ξπ = Ξπ1+ Ξπ2
Ξππ = β2 + ππ2
Thus, excess path length is
Ξ = β2 + π12 + β2 + π2
2 β π1 + π2
Assuming β << π1 , π2 and β >> π, then by substitution and Taylor Series Approximation
Ξ ββ2
2
π1 + π2π1π2
Phase difference, Ο
π =2πΞ
πβ2π
π
β2
2
π1 + π2π1π2
=π
2β2
2(π1 + π2)
ππ1π2
![Page 32: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/32.jpg)
DiffractionFresnel zones Fresnel-Kirchoff Diffraction Parameter π£ (dimensionless) characterizes phase difference between the two propagation paths is defined as
π£ = β2(π1 + π2)
ππ1π2= πΌ
2π1π2π(π1 + π2)
where β refers to the height of the obstruction and πΌ is in radians.
Phase difference, π is given as
π =π
2π£2
The phase difference between LOS and diffracted path is function of o obstructionβs height & position o transmitters and receivers height and position
![Page 33: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/33.jpg)
DiffractionFresnel zones (cont.) Fresnel Zones explains the concept of diffraction loss as a function of path difference.
Secondary waves in successive regions have a path length π/2greater than LOS path.
o nth region is the region where path length of secondary waves is n/2greater than that of LOS path length
Regions form a series of ellipsoids with foci at Tx & Rx antennas
Source:
https://upload.wikimedia.org/wikipedia/commons/4/4b/
1st_Fresnel_Zone_Avoidance.png
![Page 34: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/34.jpg)
)(
2
)(2
21
21
21
21
dd
dd
dd
ddh
v =
If h = 0, then and v are 0
TX RXd2
d1 d2d1
If and v are negative, then h
is negative
h
TX RX
DiffractionFresnel zones (cont.)
![Page 35: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/35.jpg)
DiffractionFresnel zones (cont.)
On slicing a specific ellipsoid along the plane perpendicular to LOS yields a circle with radius rn given as
β = ππ =πππ1π2π1 + π2
then Kirchoff diffraction parameter is given as
π£ = β2(π1 + π2)
ππ1π2=
πππ1π2π1 + π2
2(π1 + π2)
ππ1π2= 2π
Thus, for given π£ defines an ellipsoid with constant excess path = π/2 .
T
R
![Page 36: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/36.jpg)
DiffractionFresnel zones (cont.)1st Fresnel Zone is volume enclosed
by the first ellipsoid.
2ππ Fresnel Zone is volume
enclosed between first and the second
ellipsoid.
At receiver, the contribution to the
electric field from the successive
Fresnel Zones will be in phase
opposition and therefore will interfere
destructively rather than constructively.
21
21
2
22 dd
ddhn
Phase Difference, Ξ pertaining to πth Fresnel Zone is
![Page 37: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/37.jpg)
DiffractionFresnel zones (cont.)
Source: http://www.cdt21.com/resources/Java_file/Applet2/pk_FresnelZoneE/fresnelzone01e.gif
![Page 38: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/38.jpg)
DiffractionDiffraction Loss
Diffraction Loss is caused by blockage of secondary (diffracted) waves Partial energy from secondary waves is diffracted around an obstacleoobstruction blocks energy from some of the Fresnel zones and only a portion
of transmitted energy reaches receiver Received energy is vector sum of contributions from all unobstructed Fresnel zoneso depends on geometry of obstructiono phase of secondary (diffracted) E-field is indicated by the Fresnel Zones Obstacles may block transmission paths causing diffraction lossoconstruct a family of ellipsoids between TX & RX to represent Fresnel zones
ojoin all points for which excess path delay is multiple of π 2
ocompare geometry of obstacle with Fresnel zones to determine diffraction loss (or gain)
![Page 39: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/39.jpg)
DiffractionDiffraction Loss (cont.)
Place ideal, perfectly straight screen between Tx and Rx If top of screen is well below LOS path then screen will have little effect o the Electric field at Rx = πΈπΏππ (free
space value) As screen height increases, Electric field will vary as screen blocks more Fresnel zones The amplitude of oscillation increases until the screen is just in line with Tx and Rxofield strength = Β½ of unobstructed
field strength
If (55 to 60)% of 1st Fresnel zone is clear than further Fresnel zone clearing does not significantly alter diffraction loss
For free-space transmission conditions,1st Fresnel Zone is kept unblocked
![Page 40: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/40.jpg)
Diffraction Knife Edge Diffraction Model
Diffraction Losseso estimating attenuation caused by diffraction over obstacles is essential for predicting field strength in a given service areao not possible to estimate losses preciselyo theoretical approximations typically corrected with empirical measurements
Computing Diffraction Losseso for simple terrain: expressions have been obtained o for complex terrain: computing diffraction losses is complex
![Page 41: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/41.jpg)
Diffraction Knife Edge Diffraction Model (cont.)
Knife-edge model is the simplest model that
provides insight about magnitude of diffraction loss
o Diffraction losses are estimated using the classical Fresnel solution for field behind a knife edge
o Useful for shadowing caused by 1 knife edge object
Considers receiver R is located in shadowed region
E-field strength at R is vector sum of all fields due to secondary Huygensβ sources in the plane above the knife edge
Huygens
secondary
source
![Page 42: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/42.jpg)
Diffraction Knife Edge Diffraction Model (cont.)
The diffraction gain due to the presence of knife edge, as compared to the free space E-field
![Page 43: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/43.jpg)
Diffraction Knife Edge Diffraction Model (cont.)
![Page 44: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/44.jpg)
DiffractionMultiple Knife-Edge Diffraction Model
Bullington's model
o with more than one obstruction: compute total diffraction loss
o replace multiple obstacles with one equivalent obstacle
o use single knife edge model
Disadvantage:
o oversimplifies problem
o often produces overly optimistic estimates of received signal strength
![Page 45: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/45.jpg)
Scattering Scattering occurs when obstacle size is less than or of the order of the wavelength of propagating wave Causes the transmitter energy to be radiated in many directions Occur due to small objects, rough surfaces, and other irregularities of the channel. For example: Lamp posts and street, etc. Number of obstacles are quite large Scattering follows same principles as diffraction
![Page 46: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/46.jpg)
Scattering (cont.) Received signal strength is often stronger than that predicted by reflection/diffraction models alone
The EM wave incident upon a rough or complex surface is scattered in many directions and provides more energy at a receiver
Energy that would have been absorbed is instead reflected to the receiver
o flat surface β EM reflection (one direction)
o rough surface β EM scattering (many directions)
![Page 47: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/47.jpg)
Scattering (cont.) Critical height for surface protuberances βπ for given incident angle ππ
βπ =π
8 sin ππ
Let β be the maximum protuberances, then surface is considered
o smooth if β < βπo rough if β > βπ
![Page 48: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/48.jpg)
Reflection, Diffraction, and Scattering As a mobile moves through a region, these mechanisms have an impact on the instantaneous received signal strength
o In case LOS path exists between the devices, diffraction and scattering will not dominate the propagation.
oIf device is at a street level without LOS path, then diffraction and scattering will probably dominate the propagation.
![Page 49: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/49.jpg)
Path Loss Models Radio Propagation models are derived using a combination of empirical and analytical methods.
These methods implicitly take into account all the propagation factors both known and unknown through the actual measurements.
Path loss models are used to estimate the received signal level as a function of distance.
With the help of this model we can predict SNR for a mobile communication system.
Path loss estimation techniqueso Log - Distance Path Loss Model
o Log - Normal Shadowing
![Page 50: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/50.jpg)
Path Loss ModelsLog-distance path loss model
Average large scale path loss is
is ensemble average of all possible path loss values for given value of d
On log-log scale path loss is a straight line with slope equal to 10 n dB/decade
0
0 log10)()(d
dndPLdBPL
PL
![Page 51: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/51.jpg)
Path Loss Models (cont.)
Path loss exponent for different environments
![Page 52: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/52.jpg)
Path Loss Models (cont.)
![Page 53: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/53.jpg)
Path Loss ModelsLog-Normal Shadowing Model
Log normal
o If π is Gaussian RV and π is defined such that π = logπ, then π is log-normal RV
Shadowing
oAlso called slow-fading
oAccounts for random variations in received power observed over distances comparable to the widths of buildings
o Extra transmit power (a fading margin) must be provided to compensate for these fades
Surrounding environment clutter may be vastly different at two different locations having same T-R separation
![Page 54: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/54.jpg)
Path Loss ModelsLog-Normal Shadowing Model (cont.)
PL(d) is random and log-normally distributed about the mean distance-dependent value
ππ: zero-mean Gaussian distributed random variable (in dB) with standard deviation π
The probability that received signal level exceed a certain value πΎ is
The probability that received signal level is below πΎ is
Xd
dndPLXdPLdPL
0
0 log10)()()(
)(])(Pr[
dPQdP r
r
)(])(Pr[
dPQdP r
r
![Page 55: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/55.jpg)
Path Loss Models Outdoor Propagation
We will look to the propagation characteristics of the three outdoor environments
o Propagation in macrocells
o Propagation in microcells
o Propagation in street microcells
![Page 56: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/56.jpg)
Outdoor PropagationMacrocells
Base stations at high-points
Coverage of several kilometers
The average path loss in dB has normal distribution
oAverage path loss is a result of forward scattering over a large number of obstacles each contributing a random multiplicative factor. On changing to dB, it is a sum of random variables
o Sum is normally distributed because of central limit theorem
![Page 57: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/57.jpg)
Outdoor PropagationLongley-Rice Propagation Prediction Model Point-to-point communication in frequency range 40 MHZ to 100GHz
Also referred as irregular terrain model (ITM)
Predicts median transmission loss, takes terrain into account, uses path geometry, calculates diffraction losses
Inputs of computer program of Longley-Rice model :o Frequency
o Path length
o Polarization and antenna heights
o Surface refractivity
o Effective radius of earth
oGround conductivity
oGround dielectric constant
oClimate
![Page 58: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/58.jpg)
Outdoor PropagationLongley-Rice Propagation Prediction Model (cont.)
Computer program operates on path specific parameters
Disadvantages o Does not take into account details of terrain near the receiver
o Does not consider Buildings, Foliage, Multipath
Original model modified by Okamura for urban terrain (include extra term called urban factor)
![Page 59: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/59.jpg)
Outdoor Propagation Okumura Model
In early days, the models were based on emprical studies
Okumura did comprehesive measurements in 1968 and came up with a model.
oDiscovered that a good model for path loss was a simple power law where the exponent π is a function of the frequency, antenna heights, etc.
o It is one of the most widely used models for signal prediction in urban areas,
oValid for frequencies in: 150 MHz β 1920 MHz for distances: 1km β100km
![Page 60: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/60.jpg)
Outdoor Propagation Okumura Model (cont.)
o πΏ50: 50th percentile (i.e. median) of path loss
o πΏπΉ(π): free space propagation pathloss
o π΄ππ’(π, π): median attenuation relative to free space
o πΊ(βπ‘π): base station antenna heightgain factor
o πΊ(βππ): mobile antenna height gain factor
o πΊπ΄π πΈπ΄: gain due to different type of environment
o βπ‘π: transmitter antenna height
o βππ: receiver antenna height
πΊ βπ‘π and πΊ βππ are determined for different antenna height
πΏ50(π)(ππ΅)= πΏπΉ(π) + π΄ππ’(π, π) β πΊ(βπ‘π) β πΊ(βππ) β πΊπ΄π πΈπ΄
![Page 61: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/61.jpg)
Outdoor Propagation Okumura Model (cont.)
![Page 62: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/62.jpg)
Outdoor Propagation Okumura Model (cont.)
Advantage
o Okumurasβ model is considered to be among the simplestand best in terms of accuracy in path loss prediction formature cellular and land mobile system in a clutteredenvironment.
Disadvantage
o Low response to rapid changes in terrain
![Page 63: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/63.jpg)
Outdoor Propagation Hata Model
Empirical formulation of the graphical path loss data provided by Okumura
Valid from 150 MHz to 1500 MHz
For urban areas the formula is
πΏ π’ππππ, π ππ΅ = 69.55 + 26.16 log ππ β 13.82 log βπ‘πβ π βππ + 44.9 β 6.55 log βπ‘π log π
o d is T-R separation in km
o a(hre) is the correction factor for effective
mobile antenna height which is a
function of coverage area (different for
large and medium city)
o fc is the ferquency in MHz
o hte is effective transmitter antenna
height in meters (30-200m)
o hre is effective receiver antenna
height in meters (1-10 m)
![Page 64: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/64.jpg)
Outdoor Propagation Hata Model (cont.)
For small to medium sized city:
For large city:
In sub urban areas, path loss is:
In open rural areas, path loss is:
![Page 65: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/65.jpg)
Outdoor Propagation Hata Model (cont.)
No path specific corrections
Suitable for large cell mobile system (d >1 km)
Not suitable for PCS
![Page 66: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/66.jpg)
Outdoor Propagation PCS Extension of Hata Model
Higher frequencies: up to 2 GHz
Smaller cell sizes
Lower antenna heights
For π = 1 to 20 km
πΏ ππ΅ = 46.3 + 33.9 log ππ β 13.82 log βπ‘πβ π βππ + 44.9 β 6.55 log βπ‘π log π + πΆπ
whereπΆπ = 0 and 3 dB for medium and metro city, respectively
![Page 67: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/67.jpg)
Path Loss ModelsMicrocells
Propagation differs significantly
o Milder propagation characteristics
o Small multipath delay spread and shallow fading imply thefeasibility of higher data-rate transmission
o Mostly used in crowded urban areas
o If transmitter antenna is lower than the surrounding building thanthe signals propagate along the streets: Street Microcells
![Page 68: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/68.jpg)
Item Macrocell Microcell
Cell Radius 1 to 20km 0.1 to 1km
Tx Power 1 to 10W 0.1 to 1W
Fading Rayleigh Nakgami-Rice
RMS Delay Spread 0.1 to 10s 10 to 100ns
Max. Bit Rate 0.3 Mbps 1 Mbps
Path Loss ModelsMacrocells versus Microcells
69
![Page 69: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/69.jpg)
Path Loss Models Street Microcells
Most of the signal power propagates along the street
The signals may reach with LOS paths if the receiver is along the same street with the transmitter
The signals may reach via indirect propagation mechanisms if the receiver turns to another street
![Page 70: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/70.jpg)
Path Loss Models: Street Microcells
BA
D
C
log (distance)
received power (dB) received power (dB)
A
C
BA
D
Breakpoint
Breakpoint
n=2
n=4
n=2
n=4~8
15~20dB
Building Blocks
![Page 71: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/71.jpg)
Indoor Propagation Indoor channels are different from traditional mobile radio channels in two different ways:o The distances covered are much smaller
o The variablity of the environment is much greater for a much smaller range of T-R separation distances.
The propagation inside a building is influenced by:o Layout of the building
o Construction materials
o Building type: sports arena, residential home, factory, etc
![Page 72: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/72.jpg)
Path Loss Models Indoor Propagation
Indoor path loss models are less generalized
o Environment comparatively more dynamic
Significant features are physically smaller
o Smaller propagation distances
Less assurance of Far-field for all receiver locations and antenna types.
o More clutter, scattering, less LOS
![Page 73: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/73.jpg)
Path Loss Models Indoor Propagation (cont.)
Indoor propagation is domited by the same mechanisms as outdoor: reflection, scattering, diffraction.o However, conditions are much more variable Doors/windows open or not
The mounting place of antenna: desk, ceiling, etc.
The level of floors
Indoor channels are classified aso Line-of-sight (LOS)
o Obstructed (OBS) with varying degrees of clutter.
![Page 74: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/74.jpg)
Path Loss Models Indoor Propagation (cont.) Buiding types
o Residential homes in suburban areas
o Residential homes in urban areas
o Traditional office buildings with fixed walls (hard partitions)
o Open plan buildings with movable wall panels (soft partitions)
o Factory buildings
o Grocery stores
o Retail stores
o Sport arenas
![Page 75: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/75.jpg)
Indoor propagation Events and parameters Temporal fading for fixed and moving terminals
oMotion of people inside building causes Ricean Fading for the stationary receivers
oPortable receivers experience in general:
Rayleigh fading for obstructed propagation paths
Ricean fading for LOS paths.
Multipath Delay Spread
o Buildings with fewer metals and hard-partitions typically have small rms delay spreads: 30-60ns.
Can support data rates excess of several Mbps without equalization
o Larger buildings with great amount of metal and open aisles may have rms delay spreads as large as 300ns.
Can not support data rates more than a few hundred Kbps without equalization.
![Page 76: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/76.jpg)
Indoor propagation Models Log-distance path loss model
Same floor partition losses
oHard partitions (cannot be moved) /soft partitions (can be moved)
oInternal walls & external walls
Partition loss between floors
oDetermined by the dimensions/materials used/surroundings, including number of windows) /floor attenuation
Ericsson multiple breakpoint model
oObtained by measurements in a multiple office building
oHas 4 breakpoints and has upper & lower bound on the PL
oModel assumes 30 db attenuation at do=1m, for f=900Mhz, unity gain antenna
![Page 77: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/77.jpg)
![Page 78: Mobile Radio Propagation - Bhagalpur College of Engineering](https://reader030.vdocuments.us/reader030/viewer/2022012410/616a619e11a7b741a351dfe5/html5/thumbnails/78.jpg)
References[1] T. S. Rappaport, Wireless Communications: Principles and Practice (2nd edition), Pearson Education, 2010.
[2] S. Haykin and M. Moher, Modern Wireless Communications, Pearson Education, 2005.