mmi update programming for vehicles ... - audi-forums.com · Ó 2008 audi ag 1 of 57 29.01.2009 mmi...
TRANSCRIPT
Ó 2008 AUDI AG 1 of 57 29.01.2009
MMI update programming for vehicles equipped with MMI High (MMI2G), e.g. A8 (4E), A6 (4F),
Q7 (4L), A5 (8T) and A4 (8K) via the on-board CD drive with feedback documentation via Software
Versions Management (Audi SVM)
Note:The following screenshots may not match the texts shown on the screen of your cars.
Ó 2008 AUDI AG 2 of 57 29.01.2009
Contents
1. Overview of controls .................................................................................................................. 7
2. Update....................................................................................................................................... 8
2.1 CD packages...................................................................................................................... 8
2.2 General procedure (brief instructions) ................................................................................ 8
2.3 Important information about update programming.............................................................. 9
3. Update with MMI CD package................................................................................................. 10
3.1 Instructions of CD for intermediate update ....................................................................... 10
4. Switch on MMI. ........................................................................................................................ 11
5. Remove all CDs from the CD changer / CD player.................................................................. 12
6. Put the MMI update CD into the first slot of the CD changer or the CD drive with the label
facing up. ........................................................................................................................................ 13
7. Wait at least 2 minutes to allow the system to analyze the MMI update CD and for the MMI
System to be ready to be updated.................................................................................................. 14
8. Activate the RADIO menu by pressing the corresponding function selector button................. 15
9. First press SETUP and then RETURN and hold both buttons down simultaneously for about
5 seconds until the display changes. .............................................................................................. 16
10. Activate the SW update by pressing the bottom right control button.
............................................. 17
Ó 2008 AUDI AG 3 of 57 29.01.2009
11. Activate the update from the CD-ROM by pressing the rotary pushbutton.
............................................ 18
12. Wait at least 20 seconds while the Meta information is being read.
............................................ 19
13. Select and activate "Standard" using the rotary pushbutton.
............................................ 20
Ó 2008 AUDI AG 4 of 57 29.01.2009
14. The list which now appears shows all the devices which can be updated.
............................................ 21
15. Using the rotary pushbutton, select and confirm ”Start download” at the end of the list.
............................................ 22
16. Read the note if one appears. Then select and activate "OK" at the end of the list using the
rotary pushbutton (this only appears in the case of a bootloader update of a component).
............................................ 23
Ó 2008 AUDI AG 5 of 57 29.01.2009
17. Update programming for the individual infotainment components now starts; this can take up
to 50 minutes, depending on the vehicle equipment.
............................................ 24
18. The display automatically shows ”Start applications” when update programming is
completed. Wait until the listed devices have been initialized.
............................................ 25
19. The programming success is displayed in the overview which follows.
............................................ 26
20. Use the rotary pushbutton to scroll down the list. If a device has not been programmed
properly ("Not OK), select "Try again?" and start the update again by activating "Start download". If
Ó 2008 AUDI AG 6 of 57 29.01.2009
one of the control units cannot be flashed using this procedure (testing 2-3 times), please proceed
with the next step in the instructions. Note: If the status "OLD" appears after updating the
telephone control unit (UHV) , please proceed with the next step of the instructions.
.............................................. 27
21. Normally, every updated device is OK and you can select and activate "Restart MMI" at the
end of the list. ..................... 28
21.1 Instructions for CleanUp CD............................................................................................. 29
21.2 Instructions of the Update CD for the current software version ........................................ 40
22. Changing language of MMI speech dialogue system (SDS) ................................................ 41
23. USB – consumer update for the Audi music interface (AMI) ................................................ 47
24. SVM feedback documentation ............................................................................................. 48
25. Abbildungverzeichnis ..............................................................Error! Bookmark not defined.
Ó 2008 AUDI AG 7 of 57 29.01.2009
1. Overview of controls
Figure 1: Controls (depending on vehicle type)
� ON/OFF button with volume control
� Rotary pushbutton
� RETURN button
� Function selector buttons
� Control buttons
� Arrow buttons
� Fingerprint (not used in these instructions)
Ó 2008 AUDI AG 8 of 57 29.01.2009
2. Update
2.1 CD packages
Check the completeness of the software.
CD-Paket mit 3 CDsCD1 ZwischenupdateCD2 CleanUp-CDCD3 MMI-Update
CD-Paket mit 2 CDsCD1 CleanUp-CDCD2 MMI-Update
The part number of the CD package is included in the respective TPI or recall documents.
2.2 General procedure (brief instructions)
Information on unexpected messages and occurrences during the update see the separate
attachment.
Ó 2008 AUDI AG 9 of 57 29.01.2009
2.3 Important information about update programming
1. Check that the no-load voltage of the vehicle battery is at least 12.5V.
2. Let the engine run for 1 minute and then immediately continue with update according to the
instructions.
3. Connect a battery charger (VAS 5095) to maintain vehicle voltage throughout the entire
update programming session.
4. Switch off all equipment with high electromagnetic emission values (such as mobile
telephones or cordless land-line telephones) in and around the vehicle.
5. The Bluetooth handset (included with factory-installed Bluetooth car phone BTA) must be
switched on automatically. If not, switch on manually and repeat ignition cycle.
6. Diagnostics using the VAS tester must not be run in parallel.
7. The ignition can be switched off and remain off.
8. Switch off all unnecessary electrical equipment (daytime running lights, air conditioning, etc.)
in the vehicle and leave it switched off until all update programming has been completed.
9. Ensure that no other CDs (audio CDs, electronic on-board handbook, etc.) are in the CD
drives while running update programming.
10. It is essential that you adhere to the flash sequence!
11. Restart the MMI system after every update and check whether further control units need.
12. Ignoring the instructions may lead to hardware damage.
13. Observe the SVM feedback documentation.
14. Keep the sequence.
15. Do not leave the CDs in the car.
Ó 2008 AUDI AG 10 of 57 29.01.2009
3. Update with MMI CD package
3.1 Instructions of CD for intermediate update
Ó 2008 AUDI AG 11 of 57 29.01.2009
4. Switch on MMI.
Ó 2008 AUDI AG 12 of 57 29.01.2009
5. Remove all CDs from the CD changer / CD player.
Ó 2008 AUDI AG 13 of 57 29.01.2009
6. Put the MMI update CD into the first slot of the CD changer or theCD drive with the label facing up.
Ó 2008 AUDI AG 14 of 57 29.01.2009
7. Wait at least 2 minutes to allow the system to analyze the MMIupdate CD and for the MMI System to be ready to be updated.
Ó 2008 AUDI AG 15 of 57 29.01.2009
8. Activate the RADIO menu by pressing the corresponding functionselector button.
Ó 2008 AUDI AG 16 of 57 29.01.2009
9. First press SETUP and then RETURN and hold both buttons downsimultaneously for about 5 seconds until the display changes.
Ó 2008 AUDI AG 17 of 57 29.01.2009
10. Activate the SW update by pressing the bottom right controlbutton.
Figure 2: Selecting the SW update using the bottom right control button
Ó 2008 AUDI AG 18 of 57 29.01.2009
11. Activate the update from the CD-ROM by pressing the rotarypushbutton.
Figure 3: Selecting update of CD-ROM by pressing the rotary pushbutton
Ó 2008 AUDI AG 19 of 57 29.01.2009
12. Wait at least 20 seconds while the Meta information is beingread.
Figure 4: Waiting while the Meta information is being read
Ó 2008 AUDI AG 20 of 57 29.01.2009
13. Select and activate "Standard" using the rotary pushbutton.
Figure 5: Selecting "Standard" using the rotary pushbutton
Ó 2008 AUDI AG 21 of 57 29.01.2009
14. The list which now appears shows all the devices which can beupdated.
Figure 6: List view of the devices to be updated
Type of change:
N/A= No update information available on the present CD
N= No update required
E= Single update (partial update: bootloader or application) will be performed
J= Bootloader and application will be changed (complete update)
Ó 2008 AUDI AG 22 of 57 29.01.2009
15. Using the rotary pushbutton, select and confirm ”Startdownload” at the end of the list.
Figure 7: Activating Start download using the rotary pushbutton
Ó 2008 AUDI AG 23 of 57 29.01.2009
16. Read the note if one appears. Then select and activate "OK" atthe end of the list using the rotary pushbutton (this only appearsin the case of a bootloader update of a component).
Figure 8: Start download by selecting "OK" using the rotary pushbutton
Note:A warning message may appear informing you about the risk of damaging controlunits. You can ignore this message at this point.
Ó 2008 AUDI AG 24 of 57 29.01.2009
17. Update programming for the individual infotainmentcomponents now starts; this can take up to 50 minutes, dependingon the vehicle equipment.
Figure 9: Download progress during update programming
Ó 2008 AUDI AG 25 of 57 29.01.2009
18. The display automatically shows ”Start applications” whenupdate programming is completed. Wait until the listed deviceshave been initialized.
Figure 10: Starting applications after update programming
Ó 2008 AUDI AG 26 of 57 29.01.2009
19. The programming success is displayed in the overview whichfollows.
Figure 11: Displaying the update programming success
Ó 2008 AUDI AG 27 of 57 29.01.2009
20. Use the rotary pushbutton to scroll down the list. If a device hasnot been programmed properly ("Not OK), select "Try again?" andstart the update again by activating "Start download". If one of thecontrol units cannot be flashed using this procedure (testing 2-3times), please proceed with the next step in the instructions.Note: If the status "OLD" appears after updating the telephonecontrol unit (UHV), please proceed with the next step of the instructions.
Figure 12: Update programming successful
Ó 2008 AUDI AG 28 of 57 29.01.2009
21. Normally, every updated device is OK and you can select andactivate "Restart MMI" at the end of the list.
Figure 13: Final screen after successful update programming
ImportantWhen restarting the MMI, an additional download must be started (with a 2 minutewaiting time) after each update programming. Check and see if additional updateprogramming is necessary. The download is actually finished when there is no longera device in the list view of devices to be updated displaying a "J" or an "E" (seeFigure 6: List view of the devices to be updated).This applies to all update programming!
After restarting the MMI wait 2 minutes (so that all devices have time to log on to the system) and check
that none of the control units needs an additional update.
Note:
The process is necessary after every download to ensure correct system status.
Note:If no final screen appears (see Figure 13: Final screen after successful update
programming) and the MMI restarts automatically with user input, the update must becarried out once again as described in Chapter 3. The final screen, however, can alsoappear in English, depending on the previous status of the components. In this case,select "Restart MMI".
Continue with section 3.2.
Ó 2008 AUDI AG 29 of 57 29.01.2009
21.1 Instructions for CleanUp CD
Note:
The following steps are only necessary if a Bluetooth phone or universal phonepreparation (UHV) is installed. Otherwise contine with Update CD (current softwareversion) in chapter 3.3.
1. Switch on MMI
2. Remove all CDs from the CD changer / CD single drive.
3. Insert the CleanUp CD for the phone control unit with the writing upwards in the 1st
slot of the CD changer or in the CD single drive.
4. Wait at least 2 minutes, so that the system can analyse the CleanUp CD and the MMI
system is ready for the update.
5. Activate the radio menu.
6. Press consecutively the buttons SETUP and RETURN and hold both buttons at the
same time for about 5 seconds till the display changes.
7. Select and activate the point "phone preparation 2“ with the control button.
Figure 14: Select phone preparation 2 with the control button
Ó 2008 AUDI AG 30 of 57 29.01.2009
Important:
If Mobile-Adap. does not appear, the phone control unit cannot be accessed.
è Replace phone control unit
è Continue on page 25 with step 6
8. Check of the HW index on the screen.
Figure 15: HW-index check
Important: If HXindex: H00
è Replace phone control unit
è Continue on page 25 with step 6
9. Press Return button to go back.
10. Activate the SW update via the right lower button.
Figure 16: Select SW update via control button
Ó 2008 AUDI AG 31 of 57 29.01.2009
11. Activate "CD-Rom“ via the control button.
Figure 17: Select "CD-Rom“ via control button
12. Activate "Standard“ via the control button.
Figure 18: Select "Standard“ via control button
13. The Figure below shows all the units which can be updated.
Figure 19: Scroll down list view
14. Select and activate the point "Start download“ with the control button.
Ó 2008 AUDI AG 32 of 57 29.01.2009
Figure 20: Select menu point "Start download“
15. Select and activate in the following info window on the end of the list the point "OK“ to start
the download.
Illustration 21: Scroll down list view
Figure 21: Confirm list view with "OK“
The download takes about 6 minutes
Ó 2008 AUDI AG 33 of 57 29.01.2009
Figure 22: Download progress
16. Download is completed with display progress: 100%.
Note:
The repair program is being performed
The screen doesn't change. Wait 5 minutes.
17. The repair program has been completed.
Figure 23: Display after completed repair
Ó 2008 AUDI AG 34 of 57 29.01.2009
18. Scroll via the control button in the list to the point "phone preparation“.
Figure 24: Scroll to the list end
Figure 25: Repair "OK“ Figure 26: Repair "NOT OK“
OK Continue with à step 19 Not OK Select Try à again
The procedure starts again from step 9.
Should the 2nd attempt also result in "Not
OK“, the phone control unit cannot be
repaired.
è Replace phone control unit
è Continue on page 25 with step 6
Ó 2008 AUDI AG 35 of 57 29.01.2009
19. Select and activate "Restart MMI“ via the control button.
Figure 27: Select "Restart MMI"
20. After the reset the message "phone not available appears“.
Figure 28: Message "phone not available“ is shown
Software update to version 1130
Ó 2008 AUDI AG 36 of 57 29.01.2009
Important:
Perform the following steps with the CleanUp CD. This CD includes the data for thenew software version.
21. Press consecutively the buttons SETUP and RETURN and hold both buttons at the
same time for about 5 seconds till the display changes.
22. Activate the SW update via the right lower button.
Figure 29: Select "SWUpdate“ via control button
23. Activate "CD-Rom“ via the control button.
Figure 30: "Select "CD-Rom“ via control button
24. Activate "Standard“ via the control button.
Ó 2008 AUDI AG 37 of 57 29.01.2009
Figure 31: Select "Standard“ via control button
25. The Figure below shows all the units which can be updated.
Figure 32: Scroll down list view
Figure 33: Select "Start download“ via control button
Note:
Ó 2008 AUDI AG 38 of 57 29.01.2009
If phone preparation 2 is not listed, reset the MMI and continue with step 21
of this section.
26. Select and activate in the following info window on the end of the list the point "OK“ to start
the download.
Figure 34: Scroll down list view
Figure 35: Confirm list view with "OK
27. The update takes about 60 minutes.
Ó 2008 AUDI AG 39 of 57 29.01.2009
Figure 36: Download progress of update
28. Scroll via the control button in the list to the point "phone preparation“.
Figure 37: Scroll to list end
29. Select and activate "Restart MMI“ via the control button.
Figure 38: "Select Restart MMI“30. After the restart of the MMI check whether the phone control unit appears with the new
software version 1130.
31. Continue with section 21.2 .
Ó 2008 AUDI AG 40 of 57 29.01.2009
21.2 Instructions of the Update CD for the current software version
1. Switch on MMI.
2. Remove all CDs from the CD changer / CD single drive.
3. Insert the MMI Update CD for the phone control unit with the writing upwards in the 1st slot
of the CD changer or in the CD single drive.
4. Perform steps 4 to 19 of chapter 3.1, as described from page 6.
5. Take out the Update CD, unless an update of the voice dialog system (SDS) or Audi Music
Interface (AMI) is necessary (see chapter 4 or 5).
6. The codes and the updates of the phone control unit (R36; diagnosis address 77) andcontrol unit for display and operating unit (J523; diagnosis address 07) must be checkedwith the guided functions and if necessary corrected.
Ó 2008 AUDI AG 41 of 57 29.01.2009
22. Changing language of MMI speech dialogue system (SDS)
Note:
If you wish to change the language setting for the speech dialogue system (SDS),please perform the following steps; otherwise, go straight to the next chapter.
à Use the Update CD of the current software version to change the language.
Please inform the customer that after changing the language of the speech dialogue system
the name tags allocated by the user (names for radio stations, CDs and directory entries) will
no longer be usable. They must be deleted in the MMI using the "Setupà Settingsà
Speech dialogue systemà Delete all name tags" (see operating manual).
1. Switch on MMI.
2. Remove all CDs from the drive.
3. Put the MMI flash CD into the first slot of the CD changer or the CD drive with the label
facing up.
4. Wait at least 10 seconds to allow the system to analyse the MMI flash CD.
5. Activate the RADIO menu by pressing the corresponding function selector button.
6. First press SETUP and then RETURN and hold both buttons down simultaneously for about
5 seconds until the display changes.
7. Activate the SW update via the control button.
Figure 1439: Selecting the SW update using the bottom right control button
Ó 2008 AUDI AG 42 of 57 29.01.2009
8. Activate the update from the CD-ROM by pressing the rotary pushbutton
Figure 15: Selecting update of CD-ROM by pressing the rotary pushbutton
9. Wait for 20 seconds while the Meta information is being read.
Figure 40: Waiting while the Meta information is being read
10. Select and activate "Standard" using the rotary pushbutton.
Figure 17: Selecting "Standard" using the rotary pushbutton
Ó 2008 AUDI AG 43 of 57 29.01.2009
11. Using the rotary pushbutton, select and confirm "SDS D3" in the list that now appears.
Figure 1841: Selecting from the list of SDS devices to be updated
12. Select and activate the menu option "Select language".
Figure 1942: SDS menu option "Select language"
13. Select and activate the desired language by pressing the rotary pushbutton. A tick
(checkmark) will appear next to the selected language.
Figure 43: Selecting desired language using the rotary pushbutton
Ó 2008 AUDI AG 44 of 57 29.01.2009
14. Press the RETURN button twice. This will take you back to the selection list. "SDS D3" is not
marked with a "Y".
Figure 44: Back to the list of devices to be updated
15. Select and activate "Start download" at the end of the list using the rotary pushbutton.
Figure 2245: Activating Start download using the rotary pushbutton
16. Read the note if one appears. Then select and activate "OK" at the end of the list using the
rotary pushbutton.
Figure 46: Start download by selecting "OK" using the rotary pushbutton
Ó 2008 AUDI AG 45 of 57 29.01.2009
Note:
A warning message may appear informing you about the risk of damaging controlunits. You can ignore this message at this point.
17. The update programming will now change the system to the desired language.
Figure 2447: Update programming changes the language
18. The display automatically shows "Start applications" when update programming is complete.
Wait until the listed devices have been initialised.
Figure 48: Starting applications after update programming
Ó 2008 AUDI AG 46 of 57 29.01.2009
19. After you have completed the changes to the language setting, select "Restart MMI" (at the
end of the list) and activate your selection using the rotary pushbutton.
Figure 49: Final screen after successful update programming
20. Switch the MMI off for 10 seconds and then back on again.
21. The infotainment components will be fully functional after a delay of 3-15 minutes after the
first on/off cycle. The new language undergoes internal processing during this time.
22. Changing the language of the speed dialogue system has finished when the Speed dialogue
system clearly indicates it is ready by beeping when the speech operation button (PTT
button) in the steering wheel has been pressed with the MMI switched on.
23. You can now switch off the MMI again.
Note:
If there is a navigation system installed in the vehicle, you also have to change thelanguage for voice messages there.
Ó 2008 AUDI AG 47 of 57 29.01.2009
23. USB – consumer update for theAudi music interface (AMI)
Note:Only applicable to vehicles with PR No. 7D3 or 7D8Vehicles with Audi music interface (AMI)
A driver update of the AMI is performed using the consumer update. This allows new consumer
devices (mobile devices) to be supported and driver conflicts to be rectified.
You can find the current consumer update as well as a detailed description of the update in the
Audi Servicenet under “Accessories/Tyres --> Original accessories -> Products -> Infotainment ->
Audi music interface“.
Please check to see that the vehicle has the current driver version of the AMI control unit.
Ó 2008 AUDI AG 48 of 57 29.01.2009
24. SVM feedback documentation
The new vehicle configuration must be transmitted to Audi both after the intermediate software
update (separate CD) and after the end of the MMI Update CD package to support the fault
elimination process.
For this purpose, the VAS tester is equipped with Software Versions Management (Audi SVM).
Connect a VAS 5051 or VAS 5052 which can be used online (with current Base CD and Brand CD
version) to the vehicle’s diagnosis socket and link it up with your workshop network CPN.
Note:For later invoicing of the work carried out it is important that the vehicle data istransmitted correctly and completely. For this reason, please answer the questions at
the end of Guided Fault Finding regarding workshop order number, chassis numberand success of work carried out. Then transmit this information using the online VAStester.If you fail to do so, the work cannot be billed under warranty.
1. Turn on the ignition.
2. Switch on MMI.
3. Activate the radio menu by pressing the RADIO function selector button.
4. Start Guided Fault Finding.
Figure 50: Starting Guided Fault Finding
5. Select ”Audi” as brand.
Ó 2008 AUDI AG 49 of 57 29.01.2009
6. Select vehicle type, such as <Audi A8 2003>.
7. The tester will now establish the vehicle identification. If the tester does not do so
automatically carry out vehicle identification as usual.
8. Select engine version.
9. Follow the directions on the screen.
10. The "vehicle system test" will now be carried out, during which all fault memories will be
read. If applicable, follow additional directions on the screen.
11. When all control units have been interrogated, press ”Next” arrow (on bottom right of
screen).
12. Use the ”go to function” to select the option ”Function /Component Selection”.
Figure 51: Selecting the function/component
Ó 2008 AUDI AG 50 of 57 29.01.2009
13. Now select "Software Versions Management".
Figure 52: Software Versions Management
14. Highlight ”Problem-related hardware and software update” and then press on the Next arrow
(bottom right).Figure 53: Problem-related hardware and software update
Ó 2008 AUDI AG 51 of 57 29.01.2009
15. In the next menu, select ”Action code: Direct input" and then press the Next arrow (bottom
right).
Figure 54: Action code: Direct input
16. On the following screen, confirm "Own test plan" – "Direct input: action code for problem-
related update" by pressing the Next arrow (bottom right).
17. On the following screen select the screen button to activate the screen keypad.
Figure 55: Activating the screen keypad
Ó 2008 AUDI AG 52 of 57 29.01.2009
18. Then enter the SVM code listed in the TPL and press the Q key to confirm.
Figure 56: Entering SVM code
19. Then press Next arrow (bottom right).
20. The data for the vehicle’s control units will then be read.
Figure 57: Reading the control unit data from the vehicle
Ó 2008 AUDI AG 53 of 57 29.01.2009
21. Please enter your SeCo (GeKo) user ID.
Figure 58: SeCo user ID
22. Please enter your SeCo (GeKo) password.
23. To set up an online connection please press the ”Done” button.
Figure 59: Establishing an online connection
Ó 2008 AUDI AG 54 of 57 29.01.2009
24. The data will now be transmitted and evaluated.
Figure 60: Transmitting and evaluating data
25. You will then receive a feedback message from SVM (Software Versions Management).
Figure 61: Feedback message from Software Versions Management
If applicable, you will receive a feedback message to inform you that not all components
have accepted the update programming. Should this occur, please go through all steps once
again, starting with chapter 0. You can find information about possible feedback messages
and associated procedures in the SOST documentation, March 2007 (in the Audi Servicenet
under Technology – Product support – Electrical).
Ó 2008 AUDI AG 55 of 57 29.01.2009
26. Exit Guided Fault Finding via the "Go to" function "Quit".
Figure 62: Quitting Guided Fault Finding
27. The fault memories of all control units will now automatically be erased.
28. When you quit the programme, answer the questions regarding workshop order number,
chassis number and success of the repair work.
29. Transmit your answers via the workshop network.
30. Switch off the ignition.
31. If satellite reception is poor (e.g. in the workshop) update programming may result in the
navigation system losing its location details. For this reason, please check that the
navigation system (if fitted) is functioning correctly. To do so, press the ”NAV” button to
switch to the navigation menu.
32. Activate the map display via the bottom right control button, located next to the rotary
pushbutton (see Figure in chapter 0; button �). If a map with the correct vehicle position is
displayed, the navigation system has been initialised and you can leave out the next step.
33. If the display only shows an arrow on an empty map, the vehicle must be left standing in the
open with the MMI switched on for about 5-10 minutes.
Update programming has now been completed. Remove the update CD from thevehicle. The CD can be used for updates in other vehicles.
Thank you very much!
Ó 2008 AUDI AG 56 of 57 29.01.2009
25. List of Figures
Figure 1: Controls (depending on vehicle type)............................................................................................................. 7
Figure 2: Selecting the SW update using the bottom right control button..................................................................... 17
Figure 3: Selecting update of CD-ROM by pressing the rotary pushbutton.................................................................. 18
Figure 4: Waiting while the Meta information is being read ......................................................................................... 19
Figure 5: Selecting "Standard" using the rotary pushbutton ........................................................................................ 20
Figure 6: List view of the devices to be updated ......................................................................................................... 21
Figure 7: Activating Start download using the rotary pushbutton................................................................................. 22
Figure 8: Start download by selecting "OK" using the rotary pushbutton ..................................................................... 23
Figure 9: Download progress during update programming.......................................................................................... 24
Figure 10: Starting applications after update programming ......................................................................................... 25
Figure 11: Displaying the update programming success............................................................................................. 26
Figure 12: Update programming successful ............................................................................................................... 27
Figure 13: Final screen after successful update programming .................................................................................... 28
Figure 14: Select phone preparation 2 with the control button..................................................................................... 29
Figure 15: HW-index check........................................................................................................................................ 30
Figure 16: Select SW update via control button .......................................................................................................... 30
Figure 17: Select "CD-Rom“ via control button ........................................................................................................... 31
Figure 18: Select "Standard“ via control button........................................................................................................... 31
Figure 19: Scroll down list view .................................................................................................................................. 31
Figure 20: Select menu point "Start download“ ........................................................................................................... 32
Figure 21: Confirm list view with "OK“......................................................................................................................... 32
Figure 22: Download progress ................................................................................................................................... 33
Figure 23: Display after completed repair ................................................................................................................... 33
Figure 24: Scroll to the list end................................................................................................................................... 34
Figure 25: Repair "OK“ Figure 26: Repair "NOT OK“ ....................................................................................... 34
Figure 27: Select "Restart MMI" ................................................................................................................................. 35
Figure 28: Message "phone not available“ is shown ................................................................................................... 35
Figure 29: Select "SWUpdate“ via control button ........................................................................................................ 36
Figure 30: "Select "CD-Rom“ via control button .......................................................................................................... 36
Figure 31: Select "Standard“ via control button........................................................................................................... 37
Figure 32: Scroll down list view .................................................................................................................................. 37
Figure 33: Select "Start download“ via control button.................................................................................................. 37
Figure 34: Scroll down list view .................................................................................................................................. 38
Figure 35: Confirm list view with "OK.......................................................................................................................... 38
Figure 36: Download progress of update.................................................................................................................... 39
Figure 37: Scroll to list end......................................................................................................................................... 39
Figure 38: "Select Restart MMI“ ................................................................................................................................. 39
Figure 1414: Selecting the SW update using the bottom right control button............................................................... 41
Figure 15: Waiting while the Meta information is being read ....................................................................................... 42
Figure 1816: Selecting from the list of SDS devices to be updated ............................................................................. 43
Figure 1917: SDS menu option "Select language"...................................................................................................... 43
Ó 2008 AUDI AG 57 of 57 29.01.2009
Figure 18: Selecting desired language using the rotary pushbutton ............................................................................ 43
Figure 19: Back to the list of devices to be updated.................................................................................................... 44
Figure 2220: Activating Start download using the rotary pushbutton ........................................................................... 44
Figure 21: Start download by selecting "OK" using the rotary pushbutton ................................................................... 44
Figure 2422: Update programming changes the language.......................................................................................... 45
Figure 23: Starting applications after update programming ......................................................................................... 45
Figure 24: Final screen after successful update programming .................................................................................... 46
Figure 25: Starting Guided Fault Finding .................................................................................................................... 48
Figure 26: Selecting the function/component.............................................................................................................. 49
Figure 27: Software Versions Management................................................................................................................ 50
Figure 28: Problem-related hardware and software update......................................................................................... 50
Figure 29: Action code: Direct input............................................................................................................................ 51
Figure 30: Activating the screen keypad..................................................................................................................... 51
Figure 31: Entering SVM code ................................................................................................................................... 52
Figure 32: Reading the control unit data from the vehicle ........................................................................................... 52
Figure 33: SeCo user ID ............................................................................................................................................ 53
Figure 34: Establishing an online connection.............................................................................................................. 53
Figure 35: Transmitting and evaluating data............................................................................................................... 54
Figure 36: Feedback message from Software Versions Management......................................................................... 54
Figure 37: Quitting Guided Fault Finding .................................................................................................................... 55