MISSION CORNER DESK

Thank you for purchasing our Mission Corner Desk. Assembly of this product requires a Phillips screwdriver. We found it helpful to have a second person assist with assembly.

ANQ4070201

STEP 1 Read through these instructions thoroughly before beginning assembly. We have found this to be of great value when first assembling this product. STEP 2 Remove all parts and hardware from packing material. Wooden pieces should be placed on a non-abrasive surface (like the carton or carpet) to prevent damage to the finish. STEP 3 Identify all parts using diagram at right

STEP 4 Identify and count hardware using diagram at right. Assembly of this product requires a Phillips screwdriver. We have found it helpful to have a second person present in at least one step of the assembly.

STEP 5 Lay leg assemblies (B and C - these do NOT have holes for the removable shelf) flat with the holes facing upwards. Note the Shelf (C) has a pilot hole in the edge. These two will accommodate the long shelf (E). Insert a cam lock into each of the two holes at the top end of each assembly as shown. Ensure that the long slot in the cam lock 'points' to the hole in the top edge of the leg assembly. Screw a cam peg into each of the two predrilled holes near the bottom end of each assembly.

ANQ4070201

STEP 6 Repeat Step 5 with the other two leg assemblies (A). These two leg assemblies have holes to accommodate the removable shelf.

STEP 7 Lay shelves (D and E) flat with holes facing up. Insert a cam lock into each of the four holes. Ensure that the long slot in each cam lock 'points' to the corresponding hole in the edge of the shelf.

STEP 8 Screw 8 cam pegs into top (F) as shown at right.

ANQ4070201

STEP 9 Align holes in short edge of long shelf (E) with cam pegs in leg assembly (C) with cam locks pointing toward bottom of finished unit as shown. Press together. Secure by turning cam lock at least 1/2 turn clockwise. Repeat to attach leg assembly (B) to long shelf (E).

STEP 10 Align holes in top edges of side assemblies (B and C) with cam pegs in underside of top (F). Press together. Secure by turning cam locks at least 1/2 turn clockwise.

STEP 11 Locate leg assembly (A) with countersunk hole in bottom rail. Align holes in top edge with cam pegs in top (F) as shown. Secure by turning cam locks at least 1/2 turn clockwise. Secure leg assembly (A) to leg assembly (C) by screwing wood screw through countersunk hole in (A) and into pilot hole in (C).

ANQ4070201

STEP 12 Lay leg assembly (A) without countersunk hole flat with cam pegs pointing up. Align holes in edge of fixed shelf (D) with cam pegs. (Ensure that cam locks in shelf (D) face bottom of finished desk as shown at right.) Press pieces together. Secure assembly by turning cam locks at least 1/2 turn clockwise with Phillips screwdriver.

STEP 13 Attach assembly from Step 16 to finished unit. We found it easiest to align the holes in the leg assembly (A) with the cam pegs in the top (F) and 'rolling' the assembly to align cam pegs in the other leg assembly (A) with the holes in the edge of the shelf (D). Tighten all cam locks by turning at least 1/2 turn clockwise.

STEP 14 Ensure all fasteners are tight. Get assistance to turn unit upright. Place four wooden pins into predrilled holes on inside of leg assemblies (A). These will support the removable shelf (I).

ANQ4070201

STEP 15 Place removable shelf (G) onto wooden pins ensuring that pins engage grooves in underside of shelf.

CARE Dust as needed with a soft cloth. Clean with damp cloth and mild solution of dish soap. Polish with soft cloth and polish that contains no pigments or silicone.

www.llbean.com

Product Support 1 800 341 4341

ANQ4070201