mirror shoe cabinet (1800mm) assembly instructions · mirror shoe cabinet (1800mm) assembly...
TRANSCRIPT
Size : (W)500 x (D)300 x (H)1800 mm Colour : Black / White / Oak
500
1800
Thank you for purchasing the MIRROR SHOE CABINET.Please read the instructions carefully to ensure safe operation of the product.
Page 1 of 10
300
Batch No : PO# 2759
MIRROR SHOE CABINET (1800MM) ASSEMBLY INSTRUCTIONS
Page 2 of 10
it is recommended this weight is not exceeded. Due to the size of this product we recommend that is assembled in the room intended for use.When you ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for assemblyUnwrap all packaging materials and place the components on top of the carton box or not on a clean floor toprevent it from scratching.Check the pack and make sure you have all the parts listed.Ensure that this product is fully assembled as illustrated before use.Check all screws or bolts are tightened and inspect regularly.This product should only be used on firm, level ground.Keep small parts out of reach of children.Make sure the legs remain in contact with the ground.Tools not included.
DO NOT use power tools to construct this product.DO NOT tighten screw until fully assembled.DO NOT over tighten screw or bolts.DO NOT use this product if parts are missing, damage or worn.DO NOT stand or sit on this mirror shoes cabinet.The chest must be fitted using the wall brackets provided to avoid accidents and possible serious injuries if the item falls over or tips over during useAlways ensure the wall area to be drilled is free of electrical wires, water and gas pipes.
Never use scourers, abrasives or chemical cleaners.To clean wipe with a sponge and soapy water. Do not use solvent based cleaners or detergents as they can bleach or damage the product.
This product is intended for a maximum weight of 25.8kgs. distributed evenly throughout the cabinet.
Wall fixings supplied are suitable for solid walls. For other types of wall suitable fixings must beobtained separately . If in doubt please consult a qualified tradesperson
Side Panel (L) (15 x 298 x 1800mm)A 1B Side Panel (R) (15 x 298 x 1800mm) 1C Top Panel (15 x 298 x 470mm) 1D Bottom Panel (15 x 298 x 470mm) 1
E Front Bar Panel (15 x 60 x 470mm) 2
G Door (15 x 495 x 1736mm) 1F Rear Bar Panel (15 x 60 x 470mm) 2
Y Back Panel (2.5 x 248 x 1736mm) 1
Page 3 of 10
A
D
E
B
C
Y
Y
GF
F
E
5
3
3x
gHinges Outside
5/8”
16x
aCSK Screw
M4.7 x 38mm8x
cWooden Dowel
D6 x 30mm
16xe
Csk Screw
M3.5 x 16mm46x
dNail Pin
(26mm)4x
fNail Leg
5 x 8 x 13.5mm
Page 4 of 10
2x
iL-Mounting
Bracket
16x
jSticker19mm
2x
hWall Plug
1x
lAluminium Handle
32mm Hole2x
mDoor Buffer
10mm9x
kMetal Rod
M5 X 490mm
2x
bCSK Screw
M4 x 38mm
STEP 1
STEP 2
8 x
c
Parts Required QtyPanel (E ) 2
Page 5 of 10
b
Parts Required QtyPanel (G) 1
c
3 x
g
6 x
eg
e
STEP 2
Parts Required QtyPanel (A) 1
Panel (C) 1
Parts Required QtyPanel (D) 1
Panel (F) 2
Parts Required QtyPanel (E) 2
STEP 3
Page 6 of 10
9 x
ki
e
8 x
a
a
k
STEP 5
STEP 6g
f
f
Parts Required QtyPanel (F) 1
Parts Required QtPanel (B) 1
Page 7 of 10
g
46 x
dd
a
4 x
8 x
c
f
d
f
STEP 7
STEP 8
Page 8 of 10
Parts Required QtyPanel (F) 1
Parts Required QtPanel (G) 1
2 x
e
2 x
h
i
b
e
h
2 x
a
2 x
i
6 x
e
IMPORTANT THE CABINET MUSTBE FIXED TO THE WALL BEFORE FITTING THE DOOR
• Always ensure the wall area to be drilled is free of electrical wires, water and gas pipes.
obtained separately . If in doubt please consult a
STEP 10
STEP 9
Page 9 of 10
2 x
e
16 x
j
1 x
l
2 x
m
m
l
m
j e
Your MIRROR SHOES CABINET is now completely assembled
Page 10 of 10