Microsoft Word - DIC_Sample_Technique_revised_5-17-10.doc

CALCIFICATION ACCRETION UNIT (CAU) ASSEMBLY, DEPLOYMENT AND RECOVERY

Purpose: CAUs are deployed on the seafloor for up to three years in order to detect changes in net reef accretion.

I. CAU Assembly

-CAU materials

-Other supplies needed

-Assembly schematic

-Field gear preparation

II. CAU/BMU Deployment

-Order of operations

III. CAU/BMU Recovery/exchange

Appendix: Unit conversion chart

Section I: CAU assembly list and preparation of field gear

AssemblyCAUs are deployed in groups of 5 units. The CAU assembly diagram below (Figure 1) outlines the buildout for 1 CAU, and provides multiple views of the assembled unit.

QTY (per CAU)

Description

2

10.16cm x 10.16cm x 0.635cm (4 x 4 ) PVC plates

3

Hex jam nut, 1/4 -20, Stainless Steel (SS), regular

2

Washers, flat, 1/4, SS

3

Nylon spacers ( tall, ID, OD)

1

CAU SN tags, pigeon leg bands (https://nationalband.com/products/seamless-pigeon-bands-2048-2/)

1

Lock washer, 1/4, SS

1

Stud, full thread, 1/4 -20 x 6, SS

1

3/8, T316 SS All Thread (cut into 30.48cm [12] length stainless steel stakes and ground to a pencil tip on one side for reef penetration)

1

Wire rope clip, 3/8, 11/16 with nuts, SS T316

*Note: see unit conversion chart on the last page for inches to millimeter conversion.

Other supplies for CAU assembly and field deployment

QTY

Description

1-2 (per survey site)

Aquamend (118.29ml [4 oz.], 17.78cm [7] stick to aid in securing stainless steel stake into reef: http://www.jdindustrialsupply.com/aq7epst.html)

1

tube - Loctite thread locker (http://www.grainger.com/category/threadlockers/thread-and-gasket-sealants/adhesives-sealants-and-tape/ecatalog/N-85jZ1z0qyxd)

1

tube - Aqualube saltwater grease to ease removing nuts after long-term deployments (http://www.aqualubeky.com/grease/)

1

Heavy Duty Dive Bag, Underwater Kinetics (http://www.uwkinetics.com/products/uk-game-bag#.Vc5h5vlVhBc)

2

Sledge hammer, 1.81kg (4 lbs)

2-3

Nut driver with 11/16 socket attached

Figure 1. CAU assembly.

Field gear preparation5 CAUs (and 5 BMUs if applicable), 5-6 stainless steel stakes (bring extra in case a stake bends while driving it into the reef (stakes must be straight for proper CAU deployment), 2 sledge hammers, 5 wire rope clips (10 if deploying BMUs), 2 nut drivers, and 1 Aquamend epoxy stick (2 sticks if deploying BMUs).

Section II: CAU/BMU deployment

Deployment of CAUs and BMUs at 15 m survey siteA team of 2-3 SCUBA divers install 5 CAUs (and 5 BMUs***) in 30-40 min. The 5 CAUs, and tools needed for their deployment, should be carried in a dive bag to avoid loss of gear and tools while underwater. CAUs are deployed at 5 m spacing, along the perimeter of the 15 m survey site. The order of deployment for CAUs ONLY is:

1. Prepare log sheets with CAU serial numbers, location, depth, and other relevant notes prior to diving.

2. Drive stainless steel stakes into reef at appropriate intervals. Stakes must be vertical, so that when the CAU is attached that the plates of the unit are parallel to the sea surface, creating a flat surface for future marine organism recruitment.

3. Attach CAU to stake using a wire rope clip, tightened down with nut driver (effort should be made to deploy CAU plates parallel to the surface).

4. Apply 1/5 of the stick of Aquamend epoxy to aid in holding the stake to the reef (once the 2-part Aquamend is mixed, it is pliable for approx. 30 min).

***If BMUs are deployed with CAUs at the 15 m survey siteAdditional gear is needed for the deployment of BMUs with CAUs. BMUs should be carried in a small Pelican case (or similar, http://www.pelican-case.com/1050-clear-black.html) to protect the BMU/coral blocks from damage. Each BMU is precisely measured for size and density and unaccounted for loss of coral material from the BMU due to damage would result in inaccurate bioerosion results.

BMUs are deployed onto the SAME stainless steel stake as the CAUs are mounted. BMUs are deployed at the same depth as the reef surface.

The order of deployment for CAUs and BMUs is:

1. Prepare log sheets with CAU and BMU serial numbers, location, depth, and other relevant notes prior to diving.

2. Drive stainless steel stakes into reef at appropriate intervals. Stakes must be vertical, so that when the CAU is attached that the plates of the unit are parallel to the sea surface, creating a flat surface for future marine organism recruitment. ALSO, note that the stake placement in the reef should be in an area that allows for the BMU to be installed flat on the benthos.

3. Apply 1/5 of the stick of Aquamend epoxy to aid in holding the stake to the reef (at sites where BMUs are NOT deployed, the Aquamend epoxy is added last, after CAUs are attached to the stake. Because of the design of the BMU baseplate, when BMUs are deployed, the Aquamend used to secure the stainless steel stake to the reef must be placed prior to the BMU being secured to the stake. This allows for the BMU to be secured flush to the benthos, as well as allows for the epoxy to be used to secure the stainless steel stake into the reef. The BMU is seated into the epoxy and then secured in place with a wire rope clip.

4. Slide the BMU baseplate hole over the stainless steel stake, seating the BMU into the Aquamend, ensuring the BMU is at the same depth as the seafloor.

5. Secure BMU to stake using a wire rope clip, tightened down with nut driver (ensure BMU doesnt move/rattle loosely after wire rope clip is tightened).

6. Attach CAU to stake using a wire rope clip, tightened down with nut driver (effort should be made to deploy CAU plates parallel to the surface).

7. Apply more Aquamend, if needed, to further secure the stake into the reef.

Figure 2: CAU with BMU deployed. CAU = instrument with 2 grey PVC plates; BMU = white coral block mounted on PVC baseplate with blue serial number tag attached. Bottom wire rope clip secures the BMU to the stainless steel stake onto the benthos. Top wire rope clip secures the CAU to the stainless steel stake, with the plates squared up on-top of each other and situated parallel with the ocean surface.

Section III: CAU/BMU recovery

CAU and BMU recovery/exchangeCAUs/BMUs are deployed on stakes secured in the reef by epoxy for long-term monitoring studies. By loosening the wire rope clips, both CAU and BMU can be removed from the stake, leaving the stake in place for use again. Both CAUs and BMUs are individually bagged by SCUBA divers in a plastic bag (to ensure no loss of material during transportation to the laboratory from the field) and returned to the lab for processing. The new CAU and BMU can be reinstalled on the stake with a wire rope clip. Adding more epoxy may also make the stake deployment more secure.

Refer to CAU Processing SOP and BMU laboratory processing SOPs once out of the field.

Appendix: Unit conversion chart: inches to millimeters

US(inches)

Metric(mm)

1/8

3.18

5/32

3.97

4

3/16

4.76

5

13/64

5.16

7/32

5.56

15/64

6.05

6

1/4

6.35

17/64

6.75

7

9/32

7.14

5/16

7.94

8

11/32

8.73

9

3/8

9.53

10

11

7/16

11.11

15/32

11.91

12

1/2

12.7

13

17/32

13.49

14

9/16

14.29

15

19/32

15.08

5/8

15.88

16

21/32

16.67

17

11/16

17.46

18

19

3/4

19.05

25/32

19.84

20

13/16

20.64

21

22

7/8

22.23

23

29/32

23.02

15/16

23.81

24

31/32

24.61

25

1

25.40

26

1 1/16

26.99

27

28

1 1/8

28.58

29

30

1 3/16

30.16

31

1 1/4

31.75

32

33

1 5/16

33.34

34

1 3/8

34.93

35

36

1 7/16

36.51

38

1 1/2

38.10

39

1 9/16

39.69

40

41

1 5/8

41.28

1 11/16

42.86

1 3/4

44.45

46

1 13/16

46.04

1 7/8

47.63

1 15/16

49.21

50

2

50.80

51

2 1/8

53.96

54

2 1/4

57.15

2 3/8

60.33

2 1/2

63.5

3.5

03.

25

CAU_RevF FSCALE: 1:10DO NOT SCALE DRAWING SHEET 1 OF 1

NOAA. ANY REPRODUCTION IN PART

0314DM

DRAWING IS THE SOLE PROPERTY OF

UNLESS OTHERWISE SPECIFIED:

WEIGHT:

REVDWG. NO.

ASIZE

CAU ASSEMBLYNAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

2013

TOLERANCING PER:INTERPRET GEOMETRIC

OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF NOAA IS PROHIBITED.

123

TWO PLACE DECIMAL

45

THREE PLACE DECIMAL

APPLICATION

USED ONNEXT ASSY

PROPRIETARY AND CONFIDENTIAL

DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONAL 0.5ANGULAR: MACH 3 BEND

THE INFORMATION CONTAINED IN THIS

NOAA CRED

1125-B ALA MOANA BLVDHONOLULU, HI, 96814

808-983-3734

SERIAL NUMBER IDSEAMLESS LEG BAND FOR PIGEONS8mm ID, 10mm OD, 10mm TALLwww.nationalband.com

1/4-20 X 6 IN SS FULL THREAD STUD

1/4-20 SS NUTADD LOCTITE THREADLOCKER (GREEN 290 OR BLUE 243) OR SIMILAR THREAD ADHESIVE AFTER NUT IS NEARLY THREADED INTO POSITION

1/4 SS WASHER

4 x 4 x 1/4 PLATEGREY PVC TYPE I

1/4 NYLON SPACER1/2 TALL 1/2 OD

1/4 SS WASHER

1/4 SS LOCK WASHER

1/4-20 SS NUTADD AQUASHIELD OR SIMILAR ANTI-SEIZE

1/4-20 SS NUTADD AQUASHIELD OR SIMILAR ANTISEIZE PRODUCT

3.5

03.

25

CAU_RevF FSCALE: 1:10DO NOT SCALE DRAWING SHEET 1 OF 1

NOAA. ANY REPRODUCTION IN PART

0314DM

DRAWING IS THE SOLE PROPERTY OF

UNLESS OTHERWISE SPECIFIED:

WEIGHT:

REVDWG. NO.

ASIZE

CAU ASSEMBLYNAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

2013

TOLERANCING PER:INTERPRET GEOMETRIC

OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF NOAA IS PROHIBITED.

123

TWO PLACE DECIMAL

45

THREE PLACE DECIMAL

APPLICATION

USED ONNEXT ASSY

PROPRIETARY AND CONFIDENTIAL

DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONAL 0.5ANGULAR: MACH 3 BEND

THE INFORMATION CONTAINED IN THIS

NOAA CRED

1125-B ALA MOANA BLVDHONOLULU, HI, 96814

808-983-3734

SERIAL NUMBER IDSEAMLESS LEG BAND FOR PIGEONS8mm ID, 10mm OD, 10mm TALLwww.nationalband.com

1/4-20 X 6 IN SS FULL THREAD STUD

1/4-20 SS NUTADD LOCTITE THREADLOCKER (GREEN 290 OR BLUE 243) OR SIMILAR THREAD ADHESIVE AFTER NUT IS NEARLY THREADED INTO POSITION

1/4 SS WASHER

4 x 4 x 1/4 PLATEGREY PVC TYPE I

1/4 NYLON SPACER1/2 TALL 1/2 OD

1/4 SS WASHER

1/4 SS LOCK WASHER

1/4-20 SS NUTADD AQUASHIELD OR SIMILAR ANTI-SEIZE

1/4-20 SS NUTADD AQUASHIELD OR SIMILAR ANTISEIZE PRODUCT