michelle - css · michelle - css disc led luminaire direct/ indirect and direct css - cable...

Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 714.550.7118 fax 714.550.7151

Due to a program of continuous improvement instructions are subject to change without notice.

© 2018 Birchwood Lighting, Inc. All rights reserved.29

Note: To be installed by a qualified electrician per N.E.C. and all local codes.

INSTRUCTION SHEET

J-BOX(By others)

J-BOXBRACKET BAR8-32 BRACKETBAR SCREWS

CANOPY

CANOPY

MOUNTINGCOUPLER

AIRCRAFT CABLE

3-O or 4-0 MUD RING(By others)

CABLE GRIPPER/CANOPY

MOUNTING STUD

NC - NO CANOPY

STND - 5” CANOPY

CABLELENGTH

1/4-20 STUD BY OTHERS

SIDE EXIT CABLE

GRIPPER

POWER CORD

STRAIN RELIEF

MICHELLE - CSS Disc LED LuminaireDirect/ Indirect and Direct

CSS - Cable Suspended

1. See below for J-Box mounting centers(Jbox by others) Assure that all j-boxes are properly mounted to structure and grounded.2. Secure bracket bar to mud ring for cable next to power drop. All other cable should be attached ¼-20 stud to structure and install cable gripper. NC (No Canopy) option is available for none power cables.3. Raise fixture up and insert cables into cable grippers and adjust to desired length. 4. Insert AWM cord through canopy and secure with provided strain relief.5. Trim off excess cable, be careful not to fray.6. Complete wire make-up in J-box7. Install canopy with canopy mounting coupler.

Servicing is while fixture is suspended1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. Slide spring latch to hinge down each liner half. 3. You will have access to all drivers behind liner.4. Reassemble by following 1 and 2 steps in reverse.

Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select slot, raise and twist to lock into place.

MOUNTING CENTERS

4’ NOMINAL DIAMETER

2’ NOMINALDIAMETER

3’ NOMINALDIAMETER

28.00” B.C.

19.80”

15.58”

Ø18.00” B.C.

8.660

Ø10.0 B.C.

POWER FEED

1”

Power Feed

Power Feed

Power Feed

MOUNTING CENTERS

MOUNTING CENTERS

820-00150 V-0419





INSTRUCTION SHEET

Michelle - SM Circular LED LuminaireDirect or Dr/ In

SM - Surface Mount

1. See appropriate Stand Alone drawing for mounting locations. 1/2” lags and washer should be attached to framing.2. Remove Lens and unlatch LED liners and hinge down to acess mounting holes and drivers. 3. J-box and 4S mud ring (By others) should be centered over fixture to line up with power hole, 1” off center.4. Support Fixture near ceiling, bring wires through power hole into fixture. 4. Complete wire make-up in fixture. 5. Use 1/2” lag screws with appropriate washer to attach fixture to structure through mounting holes specified on drawing.6. Reinstall led liners.7. Install lens by grasping the fixture with one hand and rotating the lens clockwise with the other hand until it “clicks”. Once this occurs lens will float slightly but cannot fall out.

Servicing is while fixture is suspended1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. Slide spring latch to hinge down each liner half. 3. You will have access to all drivers behind liner.4. Reassemble by following 1 and 2 steps in reverse.

Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.

STUD SPACING*see appropriate drawing

Insert lagsand twist

820-00151V-0419

Liner Release

Drop Lens Flush Lens

Counter Clockwise - RemoveClockwise - Install

Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 • 714.550.7118 fax 714.550.7151

28


INSTRUCTION SHEET

48" MICHELLE

28.00” B.C.

19.80”

Ø1.000

.5621.250

REQUIRES 1/2” LAG BOLTS / WASHERS

4 5/16”

POWER FEED

1”

15.58”

Ø18.00” B.C.

36" MICHELLE

POWER FEED

1”

Ø1.000

.5621.250


8.660

Ø10.0 B.C.

POWER FEED

1”

Ø1.000

.5621.250


24" MICHELLE J-BOX(By others)

J-BOXBRACKET BAR8-32 BRACKETBAR SCREWS

CANOPY

CANOPY

MOUNTINGCOUPLER

AIRCRAFT CABLE

3-O or 4-0 MUD RING(By others)

CABLE GRIPPER/CANOPY

MOUNTING STUD

NC - NO CANOPY

STND - 5” CANOPY

CABLELENGTH

1/4-20 STUD BY OTHERS

SIDE EXIT CABLE

GRIPPER

POWER CORD

STRAIN RELIEF

MICHELLE - SM Circular LED LuminaireDirect or Dr/ In

SM - Surface Mounting Centers





INSTRUCTION SHEET

Adjustable Aircraft Cable

Mono Bracket Bar

Aircraft Cable

8/32 Bracket Bar Screws

J-Box w/ 3-0 or 4-0Mud ring(By Others)

Mono Point Coupler

CanopyAircraft Cable

Side Blocking

MICHELLE - CSS MONODisc LED LuminaireDirect/ Indirect and Direct

Mono CSS - Cable Suspended

1. Install Jbox (by others) Assure that all j-boxes are properly grounded. 2. Support the J-box with side blocking3. Screw to side blocking structure(By others)4. Secure bracket bar to mud ring.5. Run 3 cables through the Mono Point Coupler 6. Screw threaded rod into Mono Point Coupler.7. Screw 2 provided chrome couplers on thread rod8. Slide canopy over thread rod and coupler9. Screw theaded rod into bracket bar10. Raise fixture and feed 3 cables coming out of mono coupler into each adjustable cable gripper sticking out of the top lens of of fixture.11. Adjust fixture to desired height and level out with cable grippers. Trim excess cable.12. Insert AWM cord up through the hole in the canopy, into J-box. 13. Complete wire make-up14. Install canopy with magnets to bracket bar.15. Secure power cord with provided strain reliefs.

Servicing is while fixture is suspended” 1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. To release the liner, slide spring latch to hinge down each liner half. (24” uses thumb screws)3. You will have access to all drivers behind liner and keyholes for surface mounting.4. Re-assemble by following 1 - 3 steps in reverse.

Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select either flush or drop lens slot, raise and twist to lock into place.*See next page for illustrations

820-00152V-0419

Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 • 714.550.7118 fax 714.550.7151

30


INSTRUCTION SHEET

Liner Release

Drop Lens Flush Lens

Counter Clockwise - RemoveClockwise - Install

MICHELLE Disc LED LuminaireDirect/ Indirect and Direct

Fixture access for installation/service

Servicing/ Installing Fixture1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. To release the liner, slide spring latch to hinge down each liner half. (24” uses thumb screws)3. You will have access to all drivers behind liner and keyholes for surface mounting.4. Re-assemble by following 1 - 3 steps in reverse.

Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select either flush or drop lens slot, raise and twist to lock into place.

michelle - css · michelle - css disc led luminaire direct/ indirect and direct css - cable...

Documents