mic2125/6 demonstration board user's...
TRANSCRIPT
2015 Microchip Technology Inc. DS20005469A
MIC2125/6Demonstration Board
User’s Guide
DS20005469A-page 2 2015 Microchip Technology Inc.
Information contained in this publication regarding deviceapplications and the like is provided only for your convenienceand may be superseded by updates. It is your responsibility toensure that your application meets with your specifications.MICROCHIP MAKES NO REPRESENTATIONS ORWARRANTIES OF ANY KIND WHETHER EXPRESS ORIMPLIED, WRITTEN OR ORAL, STATUTORY OROTHERWISE, RELATED TO THE INFORMATION,INCLUDING BUT NOT LIMITED TO ITS CONDITION,QUALITY, PERFORMANCE, MERCHANTABILITY ORFITNESS FOR PURPOSE. Microchip disclaims all liabilityarising from this information and its use. Use of Microchipdevices in life support and/or safety applications is entirely atthe buyer’s risk, and the buyer agrees to defend, indemnify andhold harmless Microchip from any and all damages, claims,suits, or expenses resulting from such use. No licenses areconveyed, implicitly or otherwise, under any Microchipintellectual property rights unless otherwise stated.
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of ourproducts. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such actsallow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.
QUALITYMANAGEMENTSYSTEMCERTIFIEDBYDNV
== ISO/TS16949==
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.
© 2015, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
ISBN: 978-1-5224-0069-1
Object of Declaration: MIC2125/6 Demonstration Board
2015 Microchip Technology Inc. DS20005469A-page 3
NOTES:
DS20005469A-page 4 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATION BOARD USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 7
Chapter 1. Product Overview1.1 Introduction ................................................................................................... 11
1.2 MIC2125/6 Short Overview .......................................................................... 111.2.1 MIC2125/6 Key Features .......................................................................... 11
1.2.2 MIC2125/6 Overview ................................................................................. 11
1.3 What is the MIC2125/6 Demo Board? .......................................................... 121.3.1 Requirements ............................................................................................. 121.3.2 Precautions ................................................................................................ 121.3.3 Feedback Resistors.................................................................................... 131.3.4 SW Node .................................................................................................... 131.3.5 Current Limit ............................................................................................... 131.3.6 Loop Gain Measurement ............................................................................ 141.3.7 Setting the Switching Frequency................................................................ 15
1.4 MIC2125/6 Demo Board Kit Contents .......................................................... 16
Chapter 2. Installation and Operation2.1 Overview ...................................................................................................... 17
2.2 Getting Started ............................................................................................. 172.2.1 VIN Supply ................................................................................................. 17
2.2.2 Connect Load and Monitor Output ............................................................. 17
2.2.3 Enable Input ............................................................................................... 17
2.2.4 Turn On the Power ..................................................................................... 17
Appendix A. Schematics and LayoutsA.1 Introduction .................................................................................................. 19
A.2 Board - Schematic (16-Lead QFN Part) ....................................................... 20
A.3 Board - Top Layer ........................................................................................ 21
A.4 Board - Mid Layer 1 (Ground Plane) ............................................................ 21
A.5 Board - Mid Layer 2 ..................................................................................... 22
A.6 Board - Bottom Layer ................................................................................... 22
Appendix B. Bill of Materials (BOM) .................................................................................. 23
Worldwide Sales and Service .................................................................................... 26
2015 Microchip Technology Inc. DS20005469A-page 5
MIC2125/6 Demonstration Board User’s Guide
NOTES:
DS20005469A-page 6 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATION
BOARDPreface
INTRODUCTION
This chapter contains general information that will be useful to know before using the MIC2125/6 Demo Board. Items discussed in this chapter include:
• Document Layout
• Conventions Used in this Guide
• Recommended Reading
• The Microchip Web Site
• Customer Support
• Document Revision History
DOCUMENT LAYOUT
This document describes how to use the MIC2125/6 Demo Board as a developmenttool to emulate and debug firmware on a target board, as well as how to programdevices. The document is organized as follows:
• Chapter 1. “Product Overview” – Provides important information about theMIC2125/6 Demo Board and shows the hardware details of its components.
• Chapter 2. “Installation and Operation” – Includes instructions on how to use,power and test the MIC2125/6 Demo Board.
• Appendix A. “Schematics and Layouts” – Shows the schematic and layoutdiagrams for the MIC2125/6 Demo Board.
• Appendix B. “Bill of Materials (BOM)” – Lists the parts used to build theMIC2125/6 Demo Board.
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools anddocumentation are constantly evolving to meet customer needs, so some actual dialogsand/or tool descriptions may differ from those in this document. Please refer to our web site(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of eachpage, in front of the page number. The numbering convention for the DS number is“DSXXXXXXXXA”, where “XXXXXXXX” is the document number and “A” is the revision levelof the document.
For the most up-to-date information on development tools, see the MPLAB® IDE online help.Select the Help menu, and then Topics to open a list of available online help files.
2015 Microchip Technology Inc. DS20005469A-page 7
MIC2125/6 Demonstration Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description Represents Examples
Arial font:
Italic characters Referenced books MPLAB® IDE User’s Guide
Emphasized text ...is the only compiler...
Initial caps A window the Output window
A dialog the Settings dialog
A menu selection select Enable Programmer
Quotes A field name in a window or dialog
“Save project before build”
Underlined, italic text with right angle bracket
A menu path File>Save
Bold characters A dialog button Click OK
A tab Click the Power tab
N‘Rnnnn A number in verilog format, where N is the total number of digits, R is the radix and n is a digit.
4‘b0010, 2‘hF1
Text in angle brackets < > A key on the keyboard Press <Enter>, <F1>
Courier New font:
Plain Courier New Sample source code #define START
Filenames autoexec.bat
File paths c:\mcc18\h
Keywords _asm, _endasm, static
Command-line options -Opa+, -Opa-
Bit values 0, 1
Constants 0xFF, ‘A’
Italic Courier New A variable argument file.o, where file can be any valid filename
Square brackets [ ] Optional arguments mcc18 [options] file [options]
Curly brackets and pipe character: |
Choice of mutually exclusive arguments; an OR selection
errorlevel 0|1
Ellipses... Replaces repeated text var_name [, var_name...]
Represents code supplied by user
void main (void) ...
DS20005469A-page 8 2015 Microchip Technology Inc.
Preface
RECOMMENDED READING
This user's guide describes how to use the MIC2125/6 Demo Board. Another useful document is listed below. The following Microchip document is available and recommended as a supplemental reference resource:
• MIC2125/6 Data Sheet – “28V Synchronous Buck Controllers Featuring Adaptive ON-Time Control” (DS20005459)
THE MICROCHIP WEB SITE
Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information:
• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://www.microchip.com/support.
DOCUMENT REVISION HISTORY
Revision A (December 2015)
• Initial release of this document.
2015 Microchip Technology Inc .DS20005469A-page 9
MIC2125/6 Demonstration Board User’s Guide
NOTES:
DS20005469A-page 10 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATION BOARD USER’S GUIDE
Chapter 1. Product Overview
1.1 INTRODUCTION
This chapter provides an overview of the MIC2125/6 Demo Board and covers the following topics:
• MIC2125/6 Short Overview
• What is the MIC2125/6 Demo Board?
• MIC2125/6 Demo Board Kit Contents
1.2 MIC2125/6 SHORT OVERVIEW
1.2.1 MIC2125/6 Key Features
The key features of the MIC2125/6 include:
• Hyper Speed Control® Architecture Enables:
- High delta V operation (VIN = 28V and VOUT = 0.6V)
• Any Capacitor™ stable
• 4.5V to 28V Input Voltage
• Adjustable Output Voltage from 0.6V to 24V
• 200 kHz to 750 kHz Programmable Switching Frequency
• HyperLight Load® (MIC2125)
• Hyper Speed Control (MIC2126)
• Enable Input and Power Good Output
• Built-in 5V Regulator for Single-Supply Operation
• Programmable Current Limit and “Hiccup” Mode Short-Circuit Protection
• 7 ms Internal Soft-Start, Internal Compensation, and Thermal Shutdown
• Supports Safe Start-Up into a Prebiased Output
• –40°C to +125°C Junction Temperature Range
• 16-pin, 3 mm × 3 mm QFN Package
1.2.2 MIC2125/6 Overview
The MIC2125 and MIC2126 are constant-frequency synchronous buck controllersfeaturing a unique adaptive ON-time control architecture. The MIC2125/6 operate overan input voltage range from 4.5V to 28V and can be used to supply load current up to25A. The output voltage is adjustable down to 0.6V with an accuracy of ±1%. Thedevice operates with programmable switching frequency from 200 kHz to 750 kHz.
HyperLight Load® architecture operates in pulse-skipping mode at light loads, butoperates in fixed-frequency CCM mode from medium loads to heavy loads. HyperSpeed Control® architecture operates in fixed-frequency CCM mode under all loadconditions.
2015 Microchip Technology Inc. DS20005469A-page 11
MIC2125/6 Demonstration Board User’s Guide
The basic parameters of the evaluation board are:
• Input: 5V to 28V
• Output: 0.6V to 5V at 20A
• 350 kHz Switching Frequency (Adjustable from 200 kHz to 750 kHz)
FIGURE 1-1: Typical Application Circuit.
1.3 WHAT IS THE MIC2125/6 DEMO BOARD?
The MIC2125/6 Demo Board has been developed to demonstrate the capabilities ofthe MIC2125/6 device with two adaptive ON-time control architectures:
• Hyper Speed Control (MIC2126)
• HyperLight Load (MIC2125)
1.3.1 Requirements
The MIC2125 and MIC2126 evaluation boards require only a single power supply withat least 10A current capability. The MIC2125/6 each have an internal VDD LDO, so noexternal linear regulator is required to power the internal biasing of the IC. Inapplications with VIN < +5.5V, VDD should be tied to VIN to by-pass the internal linearregulator. The output load can either be a passive or an active load.
1.3.2 Precautions
The MIC2125/6 evaluation boards do not have reverse polarity protection. Applying anegative voltage to the VIN and GND terminals may damage the device. The maximumVIN of the board is rated at 28V.
VIN4.5V TO 28V
2.2μF×3 220μF
0.1μF
0.1μF
0.72μHVOUT3.3V/20A
9.09kΩ
1.2kΩ
10kΩ
56.2kΩ
2.26kΩ10kΩ
4.7nF 100μF 470μF
4.7μF
EN
PGVOUT
PVDD
VDD
AGND
EN
PG
OVP
FB
FREQ
VIN
BST
DH
SW
DL
PGND
ILIM
MIC2125/6
CAUTION
Exceeding 28V on the VIN pin can damage the device.
DS20005469A-page 12 2015 Microchip Technology Inc.
Product Overview
1.3.3 Feedback Resistors
The output voltage on the MIC2125/6 evaluation boards, which are preset to 1.2V, isdetermined by the feedback divider:
EQUATION 1-1:
All other voltages not listed above can be set by modifying RBOTTOM value accordingto Equation 1-2.
EQUATION 1-2:
Note that the output voltage should not be set to exceed 5V due to the 6.3V voltagerating on the output capacitors.
1.3.4 SW Node
Test point J1 (VSW) is placed for monitoring the switching waveform, one of the mostcritical waveforms for the converter.
1.3.5 Current Limit
The MIC2125/6 use the RDS(ON) of the low-side MOSFET and an external resistorconnected from the ILIM pin to the SW node to determine the current limit.
In each switching cycle of the MIC2125/6, the inductor current is sensed by monitoringthe low-side MOSFET in the OFF period. The sensed voltage V(ILIM) is compared withthe power ground (PGND) after a blanking time of 150 ns. In this way, the drop voltageover resistor R17 (VCL) is compared with the drop over the bottom FET, generating theshort current limit. The small capacitor (C18) connected from the ILIM pin to PGNDfilters the switching node ringing during the OFF-time, allowing a better short currentlimit measurement. The time constant created by R17 and C18 should be much lessthan the minimum OFF-time.
The VCL drop allows the programming of the short current limit through the value of theresistor (RCL). If the absolute value of the voltage drop on the bottom FET is greaterthan VCL, then V(ILIM) is lower than PGND and a short-circuit event is triggered. A hiccupcycle is then generated to treat the short-circuit event.
VOUT VREF 1R1
RBOTTOM-------------------------+
=
Where:
VREF 0.6V
RBOTTOM R4 = 0.9V
R5 = 1.0V
R6 = 1.2V
R7 = 1.5V
R8 = 1.8V
R9 = 2.5V
R10 = 3.3V
R11 = 5V
OPEN = 0.6V
RBOTTOMR1 VREFVOUT VREF–----------------------------------=
2015 Microchip Technology Inc. DS20005469A-page 13
MIC2125/6 Demonstration Board User’s Guide
The hiccup sequence, including the soft-start, reduces the stress on the switching FETsand protects the load and supply in severe short conditions.
FIGURE 1-2: MIC2125/6 Current-Limiting Circuit.
The short-circuit current-limit can be programmed by using the following formula.
EQUATION 1-3:
The MOSFET RDS(ON) varies 30% to 40% with temperature; therefore, it isrecommended to add a 50% margin to ICL in the equation above to avoid false currentlimiting due to any rise in MOSFET junction temperature. It is also recommended toconnect the SW pin directly to the drain of the low-side MOSFET to accurately sensethe MOSFET’s RDS(ON).
1.3.6 Loop Gain Measurement
The resistor, R14, is placed in series with the regulator feedback path. The control loopgain can be measured by connecting an impedance analyzer across the resistor andselecting a resistor value in between 20Ω to 50Ω.
R17ICLIM PP+ 0.5 RDS ON VCL–
ICL----------------------------------------------------------------------------------------------=
Where:
ICLIM Desired Current Limit
∆PP Inductor Current Peak-to-Peak
RDS(ON) On-Resistance of Low-Side Power MOSFET
VCL Current-Limit Threshold (Typical Value is 14 mV)
ICL Current-Limit Source Current (Typical Value is 36 µA)
DS20005469A-page 14 2015 Microchip Technology Inc.
Product Overview
1.3.7 Setting the Switching Frequency
The MIC2125/6 are adjustable-frequency, synchronous buck controllers that feature aunique adaptive ON-time control architecture. The switching frequency can beadjusted between 200 kHz and 750 kHz by changing the resistor divider network, whichconsists of R19 and R20.
FIGURE 1-3: Switching Frequency Adjustment.
The following formula gives the estimated switching frequency:
EQUATION 1-4:
For more precise setting, it is recommended to use the following graph.
FIGURE 1-4: Switching Frequency vs. R20.
The evaluation board design is optimized for a switching frequency of 350 kHz. If theswitching frequency is programmed to either the lower end or higher end, the designneeds optimization.
VDD/PVDD
SW
FB
VDD5V
2.2μFx3
AGND
MIC2125/6
BST4.7μF
PGND
VINVIN
FREQ
CS
R20
R19
fSW ADJ fOR20
R19 R20+---------------------------=
Where:
fO Switching Frequency When R19 is 100kΩ and R20 is open; fO is typically 750 kHz.
2015 Microchip Technology Inc. DS20005469A-page 15
MIC2125/6 Demonstration Board User’s Guide
1.4 MIC2125/6 DEMO BOARD KIT CONTENTS
This MIC2125/6 Demo Board kit includes the following items:
• MIC2125/6 Demo Board (MIC2125YML-20A-EV or MIC2126YML-20A-EV)
• Important Information Sheet
DS20005469A-page 16 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATION BOARD USER’S GUIDE
Chapter 2. Installation and Operation
2.1 OVERVIEWThe following sections describe how to use the MIC2125/6 Demo Board to fully evalu-ate and demonstrate the capabilities of the MIC2125/6 device.
2.2 GETTING STARTED
2.2.1 VIN Supply
Connect a supply to the VIN and GND terminals, paying careful attention to the polarity and the supply range (5V < VIN < 28V). Monitor IIN with a current meter and input volt-age at VIN and GND terminals with voltmeter. Do not apply power until step 2.2.4.
2.2.2 Connect Load and Monitor Output
Connect a load to the VOUT and GND terminals. The load can be either a passive (resistive) or an active (as in an electronic load) type. A current meter may be placed between the VOUT terminal and the load to monitor the output current. Ensure the out-put voltage is monitored at the VOUT terminal.
2.2.3 Enable Input
The EN pin has an on board 100kΩ pull-up resistor (R22) to VIN that allows the output to be turned on when VDD exceeds its UVLO threshold. An EN connector is provided on the evaluation board for users to easily access the enable feature. Applying an external logic signal on the EN pin to pull it low or using a jumper to short the EN pin to GND will shut off the output of the MIC2125/6 evaluation board.
2.2.4 Turn On the Power
Turn on the VIN supply and verify that the output voltage is regulated to 3.3V.
2015 Microchip Technology Inc. DS20005469A-page 17
MIC2125/6 Demonstration Board User’s Guide
NOTES:
DS20005469A-page 18 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATIONBOARD
Appendix A. Schematics and Layouts
A.1 INTRODUCTION
This Appendix contains the following schematics and layouts for the MIC2125/6 Demo Board (MIC2125YML-20A-EV or MIC2126YML-20A-EV):
• Board - Schematic (16-Lead QFN Part)
• Board - Top Layer
• Board - Mid Layer 1 (Ground Plane)
• Board - Mid Layer 2
• Board - Bottom Layer
2015 Microchip Technology Inc. DS20005469A-page 19
MIC2125/6 Demonstration Board User’s Guide
A.2 BOARD - SCHEMATIC (16-LEAD QFN PART)TP3TP4
TP5TP6
TP1TP2
EN
R2210kΩ
GND
D1 OPEN
C81μF
C6
R150Ω
0.1μF
R19
178kΩ
R20
121kΩ
R1849.9kΩ
PG
R231Ω
R140Ω
GND
C90.47μF
C74.7μF
C174.7μF
J9
VDD
R24
10kΩ
R21
49.9Ω
J1
VSW
L1
720nH
R25
OPENVOUT
13
14
15
16
8
7
6
5
12 11 10 9
1 2 3 4
AG
ND
NC
OV
PB
ST
VD
D
PV
VD
ILIM
DL
SWDH
FREQ
PGND
FB
PG
EN
VIN
U1MIC2125YML
U1
R16
2Ω
R17
1.2kΩC18
OPEN
VIN
TP8
TP13
TP14
TP7
C1220μF
+
C13470μF
+
C15OPEN
+
C210μF
C310μF
C124.7nF
C14100μF
C19100μF
C20100μF
C410μF
C100.1μF
C160.1μF
Q1D5 D6D7
S1 S2S3 S1 S2S3
D8Q2D5 D6D7 D8
S1 S2S3
Q3D5 D6D7 D8
S1 S2S3
Q4D5 D6D7 D8 R2
1.21Ω
C112.2nF
IRFH4213TRPB IRFH4213TRPB
IRFH4234TRPB
G G
G G
OPEN
R39.09kΩ
R110kΩ
VOUTVOUT
C211μF
C5OPEN
R13OPEN
R12OPEN
R111.37kΩ
5V
R102.26kΩ
3.3V
R93.16kΩ
2.5V
R84.99kΩ
1.8V
R76.65kΩ
1.5V
R610kΩ1.2V
R515kΩ1.0V
R430.1kΩ
0.8V
J14
2PIN
J13
2PIN
J11
2PIN J8
2PIN J7
2PIN J6
2PIN J5
2PIN J4 J3
2PIN
2PIN J2
2PIN
J12 FB
DS20005469A-page 20 2015 Microchip Technology Inc.
Schematics and Layouts
A.3 BOARD - TOP LAYER
A.4 BOARD - MID LAYER 1 (GROUND PLANE)
2015 Microchip Technology Inc. DS20005469A-page 21
MIC2125/6 Demonstration Board User’s Guide
A.5 BOARD - MID LAYER 2
A.6 BOARD - BOTTOM LAYER
DS20005469A-page 22 2015 Microchip Technology Inc.
MIC2125/6 DEMONSTRATIONBOARD
Appendix B. Bill of Materials (BOM)
TABLE B-1: BILL OF MATERIALS (BOM)
Qty. Reference Description Manufacturer Part Number
1 C1 220 µF/35V Aluminum Capacitor Nichicon UHE1V221MPD6
3 C2, C3, C4 10 µF/35V, Ceramic Capacitor, X7R, Size 1210
Murata GRM32ER7YA106K
TDK C3216X7R1V106K160AC
3 C14, C19, C20
100 µF/6.3V Ceramic Capacitor, X5R, Size 1210 Murata GRM32ER60J107M
AVX 12106D107KAT2A
TDK C3225X5R0J107M250AC
3 C6, C16, C10 0.1 µF/50V Ceramic Capacitor, X7R, Size 0603 Murata GRM188R71H104K
AVX 06035C104KAT2A
TDK C1608X7R1H104K
2 C7, C17 4.7 µF/10V Ceramic Capacitor, X7R, Size 0603 Murata GRM188C71A475K
AVX 0603ZD475KAT2A
TDK CGB3B1X5R1A475K
2 C8, C21 1 µF/6.3V Ceramic Capacitor, X7R, Size 0603 Murata GRM188R70J105K
AVX 06036C105KAT2A
TDK C1608X5R0J105K
1 C9 0.47 µF/50V Ceramic Capacitor, X7R, Size 0805 Murata GRM21BR71H474K
AVX 08055C474KAT2A
1 C11 2.2 nF/100V Ceramic Capacitor, X7R, Size 0603 Murata GRM188R72A222K
AVX 06031C222KAT2A
TDK C1608X7R2A222K
1 C12 4.7 nF/50V Ceramic Capacitor, C0G, Size 0603 Murata GRM1885C1H472J
AVX 06035A471JAT2A
TDK C1608C0G1H471J080AA
1 C13 470 µF/6.3V, 7mΩ, OSCON Sanyo 6SEPC470MX
1 C15 (OPEN) 470 µF/6.3V, POSCAP Sanyo 6TPB470M
1 C5 (OPEN) 100 µF/6.3V Ceramic Capacitor, X5R, Size 1210 Murata GRM32ER60J107M
1 C18 (OPEN) 10 pF/50V Ceramic Capacitor, C0G, Size 0603 Murata GRM1885C1H100J
AVX 06035A100JAT2A
D1 (OPEN)
1 L1 0.72 µH, 35 ASAT, 22 ARMS for 40ºC rise Wurth 744325072
1 Q1 MOSFET, N-CH, Power SO-8 IRF IRFH4234TRPB
2 Q3, Q4 MOSFET, N-CH, Power SO-8 IRF IRFH4213TRPB
1 R1 10 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060310K0FKEA
1 R2 1.21 Ω Resistor, Size 0805, 5% Vishay Dale CRCW08051R21FKEA
1 R3 9.09 kΩ, 1%, 1/10W, 0603 Vishay Dale CRCW06039K09FKEA
1 R4 30.1 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060330K1FKEA
Note: The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components.
2015 Microchip Technology Inc. DS20005469A-page 23
Bill of Materials (BOM)
1 R5 15 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060315K0FKEA
1 R6 10 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060310K0FKEA
1 R7 6.65 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW06036K65FKEA
1 R8 4.99 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW06034K99FKEA
1 R9 3.16 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW06033K16FKEA
1 R10 2.26 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW06032K26FKEA
1 R11 1.37 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW06031K37FKEA
R12, R13, R25 (OPEN)
2 R14, R15 0Ω Resistor, Size 0603, 5% Vishay Dale CRCW06030000Z0EA
1 R16 2Ω Resistor, Size 0603, 1% Vishay Dale CRCW06032R00FKEA
1 R17 750Ω Resistor, Size 0603, 1% Vishay Dale CRCW0603750RFKEA
1 R18 49.9 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060349K9FKEA
1 R19 178 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW0603178KFKEA
1 R20 121 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW0603121KFKEA
1 R21 49.9Ω Resistor, Size 0603, 1% Vishay Dale CRCW060349R9FKEA
2 R22, R24 10 kΩ Resistor, Size 0603, 1% Vishay Dale CRCW060310K0FKEA
1 R23 1Ω Resistor, Size 0603, 1% Vishay Dale CRCW06031R00FKEA
1 U1 28V Synchronous Buck Controllers Featuring Adaptive ON-Time Control
Microchip Technology Inc.
MIC2125YML
MIC2126YML
TABLE B-1: BILL OF MATERIALS (BOM) (CONTINUED)
Qty. Reference Description Manufacturer Part Number
Note: The components listed in this Bill of Materials are representative of the PCB assembly. The released BOM used in manufacturing uses all RoHS-compliant components.
2015 Microchip Technology Inc. DS20005469A-page 24
Bill of Materials (BOM)
NOTES:
2015 Microchip Technology Inc. DS20005469A-page 25
DS20005469A-page 26 2015 Microchip Technology Inc.
AMERICASCorporate Office2355 West Chandler Blvd.Chandler, AZ 85224-6199Tel: 480-792-7200 Fax: 480-792-7277Technical Support: http://www.microchip.com/supportWeb Address: www.microchip.com
AtlantaDuluth, GA Tel: 678-957-9614 Fax: 678-957-1455
Austin, TXTel: 512-257-3370
BostonWestborough, MA Tel: 774-760-0087 Fax: 774-760-0088
ChicagoItasca, IL Tel: 630-285-0071 Fax: 630-285-0075
ClevelandIndependence, OH Tel: 216-447-0464 Fax: 216-447-0643
DallasAddison, TX Tel: 972-818-7423 Fax: 972-818-2924
DetroitNovi, MI Tel: 248-848-4000
Houston, TX Tel: 281-894-5983
IndianapolisNoblesville, IN Tel: 317-773-8323Fax: 317-773-5453
Los AngelesMission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608
New York, NY Tel: 631-435-6000
San Jose, CA Tel: 408-735-9110
Canada - TorontoTel: 905-673-0699 Fax: 905-673-6509
ASIA/PACIFICAsia Pacific OfficeSuites 3707-14, 37th FloorTower 6, The GatewayHarbour City, Kowloon
Hong KongTel: 852-2943-5100Fax: 852-2401-3431
Australia - SydneyTel: 61-2-9868-6733Fax: 61-2-9868-6755
China - BeijingTel: 86-10-8569-7000 Fax: 86-10-8528-2104
China - ChengduTel: 86-28-8665-5511Fax: 86-28-8665-7889
China - ChongqingTel: 86-23-8980-9588Fax: 86-23-8980-9500
China - DongguanTel: 86-769-8702-9880
China - HangzhouTel: 86-571-8792-8115 Fax: 86-571-8792-8116
China - Hong Kong SARTel: 852-2943-5100 Fax: 852-2401-3431
China - NanjingTel: 86-25-8473-2460Fax: 86-25-8473-2470
China - QingdaoTel: 86-532-8502-7355Fax: 86-532-8502-7205
China - ShanghaiTel: 86-21-5407-5533 Fax: 86-21-5407-5066
China - ShenyangTel: 86-24-2334-2829Fax: 86-24-2334-2393
China - ShenzhenTel: 86-755-8864-2200 Fax: 86-755-8203-1760
China - WuhanTel: 86-27-5980-5300Fax: 86-27-5980-5118
China - XianTel: 86-29-8833-7252Fax: 86-29-8833-7256
ASIA/PACIFICChina - XiamenTel: 86-592-2388138 Fax: 86-592-2388130
China - ZhuhaiTel: 86-756-3210040 Fax: 86-756-3210049
India - BangaloreTel: 91-80-3090-4444 Fax: 91-80-3090-4123
India - New DelhiTel: 91-11-4160-8631Fax: 91-11-4160-8632
India - PuneTel: 91-20-3019-1500
Japan - OsakaTel: 81-6-6152-7160 Fax: 81-6-6152-9310
Japan - TokyoTel: 81-3-6880- 3770 Fax: 81-3-6880-3771
Korea - DaeguTel: 82-53-744-4301Fax: 82-53-744-4302
Korea - SeoulTel: 82-2-554-7200Fax: 82-2-558-5932 or 82-2-558-5934
Malaysia - Kuala LumpurTel: 60-3-6201-9857Fax: 60-3-6201-9859
Malaysia - PenangTel: 60-4-227-8870Fax: 60-4-227-4068
Philippines - ManilaTel: 63-2-634-9065Fax: 63-2-634-9069
SingaporeTel: 65-6334-8870Fax: 65-6334-8850
Taiwan - Hsin ChuTel: 886-3-5778-366Fax: 886-3-5770-955
Taiwan - KaohsiungTel: 886-7-213-7828
Taiwan - TaipeiTel: 886-2-2508-8600 Fax: 886-2-2508-0102
Thailand - BangkokTel: 66-2-694-1351Fax: 66-2-694-1350
EUROPEAustria - WelsTel: 43-7242-2244-39Fax: 43-7242-2244-393
Denmark - CopenhagenTel: 45-4450-2828 Fax: 45-4485-2829
France - ParisTel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Germany - DusseldorfTel: 49-2129-3766400
Germany - KarlsruheTel: 49-721-625370
Germany - MunichTel: 49-89-627-144-0 Fax: 49-89-627-144-44
Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781
Italy - VeniceTel: 39-049-7625286
Netherlands - DrunenTel: 31-416-690399 Fax: 31-416-690340
Poland - WarsawTel: 48-22-3325737
Spain - MadridTel: 34-91-708-08-90Fax: 34-91-708-08-91
Sweden - StockholmTel: 46-8-5090-4654
UK - WokinghamTel: 44-118-921-5800Fax: 44-118-921-5820
Worldwide Sales and Service
07/14/15