measuring tools introduction measuring tools for small engines are divided into three categories....
TRANSCRIPT
![Page 1: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/1.jpg)
Measuring Tools
![Page 2: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/2.jpg)
Introduction
Measuring tools for small engines are divided into three categories.– Direct reading
– Measurement transferring
– Reject gages
![Page 3: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/3.jpg)
Direct Reading Measuring Tools
Small engines use two types of direct reading measuring tools:1. Micrometers
2. Calipers
![Page 4: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/4.jpg)
Micrometers
![Page 5: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/5.jpg)
Micrometer Introduction
• A micrometer is a mechanical device designed to measure distances as small as 1/10,000 of an inch (0.0001 in).
• Micrometers are only one (1) inch long.• The micrometer is used with different
types and sizes of frames to provide precise measurements of many different objects.
• Small engines uses three (3) types of micrometers:1. Micrometer caliper
2. Inside micrometer
3. Depth gauge micrometer
Micrometer calipers are available in mechanical and digital models.
![Page 6: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/6.jpg)
Micrometer Caliper
• A micrometer caliper uses a frame that allows the micrometer to measure the thickness of objects.
• For small engine use, different frame sizes are used to provide a wider measurement range.– One inch
– Two inch
– Etc.
![Page 7: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/7.jpg)
Reading Micrometer Caliper-parts
• The first step in being able to read a micrometer is learning the names of the parts. The face of the anvil and the
face of the spindle are the contact surfaces.
The spindle and thimble turn together.
The ratchet/friction stop improves the repeatability of measurements for beginners.
A micrometer caliper is read at the point were the edge of the thimble crosses the barrel scale
• Insure the lock is released before trying to turn the thimble..
![Page 8: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/8.jpg)
Reading Micrometer Caliper-barrel
• A micrometer caliper is read just like an ruler.
• Start by determining the smallest whole unit, and then determine the values of each sub division.
• The smallest whole unit is determined by the frame size.– One (1) inch frame = 0.0
smallest whole unit
– Two (2) inch frame = 1.0 smallest whole unit.
– Etc.
• The micrometer barrel scale is one (1) inch long and is divided into ten (10) sections.
• Each number on the barrel scale = 1/10 or 0.1 inch.
![Page 9: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/9.jpg)
Reading Micrometer Caliper-barrel
• Each 1/10 of an inch on the barrel scale is divided into 4 segments.
• Each short line = 0.25 inches (25 thousands of an inch).
€
110
÷ 4 =110
x14
=140
= 0.025
![Page 10: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/10.jpg)
Reading Micrometer Caliper-thimble
• The last step is reading the value on the thimble scale.• The thimble scale subdivides the last segment on the barrel
scale.
• The smallest segment on the barrel is 25 thousands (0.025).
• The thimble is divided into 25 segments = 1/1,000 or 0.001 inch.
![Page 11: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/11.jpg)
Micrometer Caliper Example
• Determine the reading for the micrometer caliper in the illustration.
1. Smallest whole unit 0.0002. Tenths of an inch 0.3003. Twenty five thousands ( 0.025 x 2 ) 0.0504. Thousands 0.015 Sum (measurement) 0.365
![Page 12: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/12.jpg)
Micrometer Caliper-digital
• Most measuring tools are available with a digital readout.
• Advantages– Easier to read.
– Can be interfaced with data collection devices for automatic recording.
– Easy to convert between English and metric units.
• Disadvantages– Requires battery
– More expensive
![Page 13: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/13.jpg)
Inside Micrometer
• Inside micrometers have been replaced by dial calipers and other tools for small gas engines.
• The principles for reading are the same.
• The primary difference is determining the smallest whole unit.
• The physical size of the micrometer limits the smallest whole unit to 1 or 1-1/2 inch.
• Extensions are added to set the minimum size to the desired range.
![Page 14: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/14.jpg)
Inside Micrometer Example
Read the inside micrometer in the illustration.
Smallest whole unit 1.500
Tenths 0.200
Twenty Five Thousands 0.025
Thimble 0.014
Sum (reading) 1.734
![Page 15: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/15.jpg)
Inside Micrometer Example 2
• Inside micrometers use extensions to change the range of measurements.
• Adding an extension increases the minimum measurement.
Smallest whole unit 2.000Tenths 0.200Twenty five thousands 0.075Thousands 0.001 Reading 2.276
In this example a 1/2 inch extension has been added.
Note: when the zero on the thimble is close to the reference line and a 25 thousands line is close to the edge of the thimble, it may be difficult to determine if the last line that should be counted. If the thimble zero is above the reference line the line is not counted. If it is below it should be counted.
![Page 16: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/16.jpg)
Depth Gauge Micrometer
• Depth gauge micrometers are used to measure the depth of blind holes, slots, key ways, etc.
• The spindle length can be changed to set the micrometer for the desired range of measurement.
• To read a depth gauge micrometer you must visualize the distance that has been covered by the thimble.
Thimble
Spindle
![Page 17: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/17.jpg)
Depth Gauge Micrometer Example
Smallest whole unit0.000
Tenths0.800
Twenty Five Thousands0.050
Thousands0.017
Sum (reading)0.867
Read the depth gauge micrometer in the illustration
![Page 18: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/18.jpg)
Calipers
![Page 19: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/19.jpg)
Introduction
• Calipers can be direct reading or measuring transferring tools.• Direct reading calipers are capable of a wider measurement
range than micrometer calipers.– Six (6), eighteen (18) and twenty four (24) inch are popular.
• Three common designs of direct reading calipers;– Vernier
– Dial
– Digital
![Page 20: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/20.jpg)
Vernier Caliper
• Vernier calipers are an old tool that has been mostly replaced by dial and digital calipers.
• They are manufactured with decimal scales, metric scales and fractional scales.
• The Vernier scale is still used on many mechanical measuring tools.
![Page 21: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/21.jpg)
Vernier Scale
• The reference point is the 0 on the vernier scale.• To read a Vernier, the line of coincidence must be located.• The line of coincidence (LOC) is the line on the Vernier that
coincides with a line on the main scale.– Illustration LOC = 19
• In theory only one LOC is possible, but usually when reading the vernier it appears several exist. When this occurs pick the middle line.
• A Vernier is a mechanical means of magnifying the last segment on the main scale so addition subdivisions can be made.
![Page 22: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/22.jpg)
Vernier Caliper-practice
• Smallest whole unit 1.000• Tenths of an inch 0.200• Twenty five thousands 0.000• Vernier scale 0.011 Sum (measurement) 1.211
LOC
Read the Vernier caliper in the illustration.
![Page 23: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/23.jpg)
Dial Caliper
A dial replaces the Vernier.
This makes the caliper easier to read.
The reader must still determine the units and graduations.
![Page 24: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/24.jpg)
Measurement Transferring Tools
![Page 25: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/25.jpg)
Introduction
• Measurement transferring tools are tools that collect a measurement, but do not have a scale to read the measurement.
• Common tools are:– Spring calipers
– Dividers
– Telescoping gauges
– Ball gauges
![Page 26: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/26.jpg)
Spring Calipers
• Spring calipers are used to transfer measurements.
• Three types of spring calipers– Outside
– Inside
– Hermaphrodite
![Page 27: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/27.jpg)
Dividers
• Dividers are very useful for laying out several equal distances or transferring a distance measurement when other measuring devices cannot be used.
![Page 28: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/28.jpg)
Telescoping gages
• Telescoping gages are used to measure inside diameters.
• One or both ends are spring loaded so they can be retracted and inserted into the hole being measured.
• The measurement is made with a caliper or micrometer.
![Page 29: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/29.jpg)
Ball Gauges
• Ball gauges are use to transfer measurements that are too small for telescoping gauges.
• The ball is split and a tapered wedge is used to increase and decrease the diameter of the ball halves.
![Page 30: Measuring Tools Introduction Measuring tools for small engines are divided into three categories. –Direct reading –Measurement transferring –Reject gages](https://reader036.vdocuments.us/reader036/viewer/2022062320/56649ce25503460f949adeaa/html5/thumbnails/30.jpg)
The End