mcm04 competitive manufacturing training package · certificate ii in manufacturing technology as...
TRANSCRIPT
MCM04 Competitive ManufacturingTraining Package
Volume 1 of 2
Version Number: 3Review Date: 31 July 2006
MCM04Competitive Manufacturing Training Package
This is Volume 1 of a 2-volume set. This volume should not be used in isolation but in thecontext of the complete set for the Competitive Manufacturing Training Package.
The material contained within this volume is part of the endorsed component of theCompetitive Manufacturing Training Package endorsed by the National Training QualityCouncil in September, 2004 and agreed by the Ministers.
Volume 1 of 2Competitive Manufacturing Training Package (Background, Qualification
Framework, Assessment Guidelines)
Covering the manufacturing sectors of:
Automotive Manufacturing
Chemical, Hydrocarbons and Oil Refining
Food Processing
Furnishing
Manufactured Mineral Products
Metal and Engineering
Sugar Milling
Textiles, Clothing and Footwear
Plastics, Rubber and Cable making, and related sectors
Volume 1 Background, Qualifications Framework, Assessment Guidelines
Volume 2 Units of Competency
This Training Package is to be reviewed by 31 July 2006.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Title Page
Volume 1 of 2 Page 1 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 - Competitive Manufacturing Training Package
© Commonwealth of Australia, 2004
This work has been produced with the assistance of funding provided by the CommonwealthGovernment through the Department of Education, Science and Training (DEST).
An individual may make a photocopy of all or part of the work for their personal use.
A Registered Training Organisation may make photocopies of all or part of the work for theteaching purposes of that organisation, including for supply to its students provided that anyconsideration does not exceed the marginal cost of preparation, reproduction, assembly anddelivery.
Except as permitted under the Copyright Act 1968, all other rights are reserved. Requests forpermission may be directed to:
Branch Manager,
Technology and Information Services Branch,
Industry Skills Development Group,
Department of Education, Science and Training,
GPO Box 9880 Canberra City, ACT, 2601.
Website: www.dest.gov.au
This work is the result of wide consultations with Australian industry participants. It is acollaborative view and does not necessarily represent the view of DEST or any specific body.For the sake of brevity it may omit factors which could be pertinent in particular cases.
While care has been taken in the preparation of this Training Package, DEST and the originaldeveloper do not warrant that any licensing or registration requirements specified here areeither complete or up-to-date for your State or Territory. DEST and the original developer donot accept any liability for any damage or loss (including indirect and consequential loss)incurred by any person as a result of relying on the information contained in this TrainingPackage.
This Training Package should not be regarded as professional advice and it should not berelied upon in any important matter without obtaining appropriate advice relevant to yourcircumstances.
Published by:
First published: 1 June 2004
ISBN: 0 642 80176 2
Printed by:
AEShareNet Code: P
Print Version No: 3
Release Date: September, 2004
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Imprint Page
Volume 1 of 2 Page 2 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
TABLE OF CONTENTS
Preliminary Information .......................................................................................................................................4
Important Note to Users...................................................................................................................................... 4Summary of AQF qualifications in this Training Package................................................................................... 5Units of competency in this Training Package and their prerequisites................................................................6Imported units of competency in this Training Package....................................................................................10
Overview.............................................................................................................................................................. 13
What is a Training Package? ........................................................................................................................... 13Training Package Endorsed Components ........................................................................................................14Training Package, Qualification and Unit of Competency Codes .....................................................................15Training Package, Qualification and Unit of Competency Titles ...................................................................... 16
Introduction to the Competitive Manufacturing Training Package................................................................ 16
Development of MCM04....................................................................................................................................18
Qualifications Framework.................................................................................................................................. 21
The Australian Qualifications Framework..........................................................................................................21Skill Sets............................................................................................................................................................32
Qualifications...................................................................................................................................................... 33
MCM20105 Certificate II in Manufacturing Technology.................................................................................... 33MCM20205 Certificate II in Competitive Manufacturing.................................................................................... 36MCM30104 Certificate III in Competitive Manufacturing................................................................................... 39MCM30204 Certificate III in Manufacturing Technology................................................................................... 44MCM40104 Certificate IV in Competitive Manufacturing...................................................................................53MCM40204 Certificate IV in Manufacturing Technology................................................................................... 56MCM50104 Diploma of Competitive Manufacturing..........................................................................................65MCM60104 Advanced Diploma of Competitive Manufacturing.........................................................................69
Assessment Guidelines......................................................................................................................................73
Introduction........................................................................................................................................................73Assessment System Overview..........................................................................................................................73Australian Quality Training Framework Assessment Requirements................................................................. 73Pathways...........................................................................................................................................................74
Designing Assessment Tools............................................................................................................................ 77
Use of Assessment Tools..................................................................................................................................77Using Prepared Assessment Tools................................................................................................................... 77Developing Assessment Tools.......................................................................................................................... 77Conducting Assessment....................................................................................................................................78Access and Equity.............................................................................................................................................79Assessment for Competitive Manufacturing......................................................................................................79Futher Sources of Information...........................................................................................................................80General Resources........................................................................................................................................... 80Assessment Resources.....................................................................................................................................81Assessment Tool Design and Conducting Assessment....................................................................................81Assessor Training..............................................................................................................................................81Assessment System Design and Management.................................................................................................82
Competency Standards...................................................................................................................................... 83
What is competency? ....................................................................................................................................... 83Contextualisation of Units of Competency by RTOs ........................................................................................ 83Components of Units of Competency ...............................................................................................................83Key Competencies ........................................................................................................................................... 85Performance Levels ......................................................................................................................................... 86
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Table of Contents
Volume 1 of 2 Page 3 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Preliminary Information
Important Note to Users
Training Packages are not static documents; they are amended periodically to reflect thelatest industry practices and are version controlled. It is essential that the latest version isalways used.
Check the version number before commencing training or assessment
This Training Package is Version 3 - check whether this is the latest version by going to theNational Training Information Service ( www.ntis.gov.au) and locating information about theTraining Package. Alternatively, contact Manufacturing Industry Skills Council athttp://www.mskills.org.au to confirm the latest version number.
Explanation of version number conventions
The primary release Training Package is Version 1. When changes are made to a TrainingPackage, sometimes the version number is changed and sometimes it is not, depending onthe extent of the change. When a Training Package is reviewed it is considered to be a newTraining Package for the purposes of version control, and is Version 1. Do not confuse theversion number with the Training Packages national code (which remains the same during itsperiod of endorsement).
Version modification history
The version details of this endorsed Training Package are in the table below. The latestinformation is at the top of the table.
Version Release Date Comments
1 September,2004
Initial release
2 April, 2005 Inclusion of Certificates III and IV in Manufacturing Technologyand new units of competency.
Minor corrections (including to the diagram) to clarify packagingrules for Certificates III and IV in Competitive Manufacturing
Replacement of Assessment Guidelines to reflect theendorsement of TAA04.
3 April 2006 Inclusion of Certificate II in Competitive Manufacturing,Certificate II in Manufacturing Technology as well as their newunits of competency and additional elective units for existingqualifications.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 4 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Summary of AQF qualifications in this Training Package
Code Title
MCM20105 Certificate II in Manufacturing Technology
MCM20205 Certificate II in Competitive Manufacturing
MCM30104 Certificate III in Competitive Manufacturing
MCM30204 Certificate III in Manufacturing Technology
MCM40104 Certificate IV in Competitive Manufacturing
MCM40204 Certificate IV in Manufacturing Technology
MCM50104 Diploma of Competitive Manufacturing
MCM60104 Advanced Diploma of Competitive Manufacturing
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 5 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Units of competency in this Training Package and their prerequisites
Code Title Prerequisite
MCMC210A Manage the impact of change on own work None
MCMC410A Lead change in a manufacturing environment None
MCMC411A Lead a competitive manufacturing team None
MCMC413A Lead team culture improvement None
MCMC610A Manage relationships with non-customer externalorganisations
None
MCMC611A Manage people relationships None
MCMC612A Manage workplace learning None
MCMC613A Facilitate holistic culture improvement in a manufacturingenterprise
None
MCMC614A Develop a communications strategy to support production None
MCMO290A Work safely in manufacturing None
MCMP295A Operate manufacturing equipment None
MCMP296A Make a small furniture item from timber None
MCMP297A Make an object from cloth using an existing pattern None
MCMP298A Make an object from metal None
MCMP299A Make an object from plastic None
MCMS200A Apply competitive manufacturing practices None
MCMS201A Sustain process improvements None
MCMS400A Implement a competitive manufacturing system None
MCMS401A Ensure process improvements are sustained None
MCMS405A Lead a manufacturing team using a balanced score cardapproach
None
MCMS600A Develop a competitive manufacturing system None
MCMS601A Analyse and map a value chain None
MCMS602A Manage a value chain MCMS601AMCMT631A
MCMS603A Develop manufacturing related business plans None
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 6 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Code Title Prerequisite
MCMS604A Manage competitive manufacturing processes in a jobbingshop environment
MCMS601AMCMT280AMCMT631A
MCMS605A Develop a balanced score card MCMS601AMCMT280AMCMT631A
MCMS606A Introduce competitive manufacturing to a small or mediumenterprise
None
MCMT220A Apply quick changeover procedures None
MCMT221A Apply Just in Time (JIT) procedures None
MCMT230A Apply cost factors to work practices None
MCMT231A Interpret product costs in terms of customer requirements None
MCMT240A Apply 5S procedures in a manufacturing environment None
MCMT250A Monitor process capability None
MCMT251A Apply quality standards None
MCMT260A Use planning software systems in manufacturing None
MCMT261A Use SCADA systems in manufacturing None
MCMT270A Use sustainable energy practices None
MCMT271A Use sustainable environmental practices None
MCMT280A Undertake root cause analysis None
MCMT281A Contribute to the application of a proactive maintenancestrategy
None
MCMT421A Facilitate a Just in Time (JIT) system None
MCMT423A Monitor a manufacturing levelled pull system None
MCMT430A Improve cost factors in work practices None
MCMT432A Analyse manual handling processes None
MCMT440A Lead 5S in a manufacturing environment None
MCMT441A Facilitate continuous improvement in manufacturing None
MCMT450A Undertake process capability improvements None
MCMT451A Mistake proof a production process None
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 7 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Code Title Prerequisite
MCMT452A Apply statistics to processes in manufacturing None
MCMT453A Use six sigma techniques MCMT452A
MCMT460A Facilitate the use of planning software systems inmanufacturing
None
MCMT461A Facilitate SCADA systems in a manufacturing team orwork area
MCMT261A
MCMT481A Undertake proactive maintenance analyses None
MCMT482A Assist in implementing a proactive maintenance strategy None
MCMT483A Support proactive maintenance None
MCMT620A Develop quick changeover procedures None
MCMT621A Develop a Just in Time (JIT) system None
MCMT622A Design a process layout None
MCMT623A Develop a levelled pull system of manufacturing None
MCMT630A Optimise cost of product None
MCMT631A Undertake value analysis of product costs in terms ofcustomer requirements
None
MCMT632A Analyse cost implications of maintenance strategy None
MCMT640A Manage 5S system in a manufacturing environment None
MCMT641A Implement a continuous improvement system None
MCMT650A Determine and improve process capability None
MCMT652A Design an experiment MCMT452A
MCMT653A Apply six sigma to process control and improvement MCMT452A
MCMT660A Develop the application of enterprise systems inmanufacturing
None
MCMT661A Determine and establish information collectionrequirements and processes
None
MCMT662A Develop a documentation control strategy for amanufacturing enterprise
None
MCMT670A Develop and manage sustainable energy practices None
MCMT671A Develop and manage sustainable environmental practices None
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 8 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Code Title Prerequisite
MCMT675A Facilitate the development of a new product None
MCMT681A Develop a proactive maintenance strategy None
MCMT682A Adapt a proactive maintenance strategy to the processmanufacturing sector
MCMT681A
MCMT683A Adapt a proactive maintenance strategy for a seasonal orcyclical manufacturing operation
MCMT681A
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 9 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Imported units of competency in this Training Package
Code Title Origin
AUM4003A Interpret customer requirements - complex AUM00
FDFOPTSD2A Work in a socially diverse environment FDF03
LMTPDTX04A Contribute to the development of products or processes LMT00
LMTPRGN05A Participate in product engineering LMT00
MEM12024A Perform computations MEM05
MEM15001B Perform basic statistical quality control MEM05
MEM16006A Organise and communicate information MEM05
MEM16008A Interact with computing technology MEM05
MEM30001A Use computer aided drafting systems to produce basicengineering drawings
MEM05
MEM30002A Produce basic engineering graphics MEM05
MEM30003A Produce detailed engineering drawings MEM05
MEM30004A Use CAD to create and display 3D models MEM05
MEM30005A Calculate force systems within simple beam structures MEM05
MEM30006A Calculate stresses in simple structures MEM05
MEM30007A Select common engineering materials MEM05
MEM30008A Apply basic economic and ergonomic concepts to evaluateengineering applications
MEM05
MEM30009A Contribute to the design of basic mechanical systems MEM05
MEM30010A Set up basic hydraulic circuits MEM05
MEM30011A Set up basic pneumatic circuits MEM05
MEM30012A Apply mathematical techniques in a manufacturingengineering or related environment
MEM05
MEM30013A Assist in the preparation of a basic workplace layout MEM05
MEM30014A Apply basic just in time systems to the reduction of waste MEM05
MEM30015A Develop recommendations for basic set up timeimprovements
MEM05
MEM30016A Assist in the analysis of a supply chain MEM05
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 10 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Code Title Origin
MEM30017A Use basic preventative maintenance techniques and tools MEM05
MEM30018A Undertake basic process planning MEM05
MEM30019A Use resource planning software systems in manufacturing MEM05
MEM30020A Develop and manage a plan for a simple manufacturingrelated project
MEM05
MEM30021A Prepare a simple production schedule MEM05
MEM30022A Undertake supervised procurement activities MEM05
MEM30023A Prepare a simple cost estimate for a manufactured product MEM05
MEM30024A Participate in quality assurance techniques MEM05
MEM30025A Analyse a simple electrical system circuit MEM05
PMASUP390A Use structured problem solving tools PMA02
PMLCOM300B Communicate with other people PML04
PMLDATA200A Record and present data PML04
PMLMAIN300B Maintain the laboratory fit for purpose PML04
PMLOHS301B Work safely with instruments that emit ionising radiation PML04
PMLOHS302A Participate in laboratory/field workplace safety PML04
PMLORG301A Plan and conduct laboratory/field work PML04
PMLQUAL300B Contribute to the achievement of quality objectives PML04
PMLQUAL301B Apply critical control point requirements PML04
PMLQUAL401B Apply quality system and continuous improvementprocesses
PML04
PMLSAMP200A Collect routine site samples PML04
PMLSAMP201A Handle and transport samples or equipment PML04
PMLSAMP302A Receive and prepare samples for testing PML04
PMLSAMP400B Obtain representative samples in accordance withsampling plan
PML04
PMLSCIG300B Operate basic handblowing equipment PML04
PMLSCIG301B Repair glass apparatus using simple glassblowingequipment
PML04
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 11 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Code Title Origin
PMLTEST300B Perform basic tests PML04
PMLTEST303B Prepare working solutions PML04
PMLTEST304B Prepare culture media PML04
PMLTEST305B Perform aseptic techniques PML04
PMLTEST306B Assist with fieldwork PML04
PMLTEST307B Prepare trial batches for evaluation PML04
PMLTEST308A Perform microscopic examination PML04
UTPNEG147A Perform electrical/electronic drafting UTP98
Explanation of the review date
The review date (shown on the title page and in the header of each page) indicates when the TrainingPackage is expected to be reviewed in the light of changes such as changing technologies andcircumstances. The review date is not an expiry date. Endorsed Training Packages and theircomponents remain current until they are reviewed or replaced.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Preliminary Information
Volume 1 of 2 Page 12 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Overview
What is a Training Package?
A Training Package is an integrated set of nationally endorsed competency standards,assessment guidelines and Australian Qualifications Framework (AQF) qualifications for aspecific industry, industry sector or enterprise.
Each Training Package:
• provides a consistent and reliable set of components for training, recognising andassessing peoples skills, and may also have optional support materials
• enables nationally recognised qualifications to be awarded through direct assessment ofworkplace competencies
• encourages the development and delivery of flexible training which suits individual andindustry requirements
• encourages learning and assessment in a work-related environment which leads toverifiable workplace outcomes.
How do Training Packages fit within the National Training Framework?
The National Training Framework is made up of the nationally agreed quality arrangementsfor the vocational education and training sector, the Australian Quality Training Framework(AQTF), and Training Packages endorsed by the National Training Quality Council (NTQC).
How are Training Packages developed?
Training Packages are developed by Industry Skills Councils or enterprises to meet theidentified training needs of specific industries or industry sectors. To gain nationalendorsement of Training Packages, developers must provide evidence of extensive research,consultation and support within the industry area or enterprise.
How do Training Packages encourage flexibility?
Training Packages describe the skills and knowledge needed to perform effectively in theworkplace without prescribing how people should be trained.
Training Packages acknowledge that people can achieve vocational competency in manyways by emphasising what the learner can do, not how or where they learned to do it. Forexample, some experienced workers might be able to demonstrate competency against theunits of competency, and even gain a qualification, without completing a formal trainingprogram.
With Training Packages, assessment and training may be conducted at the workplace,off-the-job, at a training organisation, during regular work, or through work experience, workplacement, work simulation or any combination of these.
Who can deliver and assess using Training Packages?
Training and assessment using Training Packages must be conducted by a RegisteredTraining Organisation (RTO) that has the qualifications or specific units of competency on itsscope of registration, or that works in partnership with another RTO as specified in the AQTFStandards for Registered Training Organisations.
Training Package Components
Training Packages are made up of mandatory components endorsed by the NTQC, andoptional support materials.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 13 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Training Package Endorsed Components
The nationally endorsed components include the Competency Standards, AssessmentGuidelines and Qualifications Framework. These form the basis of training and assessment inthe Training Package and, as such, they must be used.
Competency Standards
Each unit of competency identifies a discrete workplace requirement and includes theknowledge and skills that underpin competency as well as language, literacy and numeracy;and occupational health and safety requirements. The units of competency must be adheredto in training and assessment to ensure consistency of outcomes.
Assessment Guidelines
The Assessment Guidelines provide an industry framework to ensure all assessments meetindustry needs and nationally agreed standards as expressed in the Training Package andthe Standards for Registered Training Organisations. The Assessment Guidelines must befollowed to ensure the integrity of assessment leading to nationally recognised qualifications.
Qualifications Framework
Each Training Package provides details of those units of competency that must be achievedto award AQF qualifications. The rules around which units of competency can be combined tomake up a valid AQF qualification in the Training Package are referred to as the packagingrules. The packaging rules must be followed to ensure the integrity of nationally recognisedqualifications issued.
Training Package Support Materials
The endorsed components of Training Packages are complemented and supported byoptional support materials that provide for choice in the design of training and assessment tomeet the needs of industry and learners.
Training Package support materials can relate to single or multiple units of competency, anindustry sector, a qualification or the whole Training Package. They tend to fall into one ormore of the categories illustrated below.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 14 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Training Package support materials are produced by a range of stakeholders such as RTOs,individual trainers and assessors, private and commercial developers and Governmentagencies.
Where such materials have been quality assured through a process of noting by the NTQC,they display the following official logo. Noted support materials are listed on the NationalTraining Information Service (NTIS), together with a detailed description and information onthe type of product and its availability ( www.ntis.gov.au).
It is not compulsory to submit support materials for noting; any resources that meet therequirements of the Training Package can be used.
Training Package, Qualification and Unit of Competency Codes
There are agreed conventions for the national codes used for Training Packages and theircomponents. Always use the correct codes, exactly as they appear in the Training Package,and with the title always following the code.
Training Package Codes
Each Training Package has a unique five-character national code assigned when the TrainingPackage is endorsed, for example MCM04. The first three characters are letters identifyingthe Training Package industry coverage and the last two characters are numbers identifyingthe year of endorsement.
Qualification Codes
Within each Training Package, each qualification has a unique eight-character code, forexample MCM20105. The first three letters identify the Training Package; the first numberidentifies the qualification level (noting that arabic numbers are not used in qualification titlesthemselves); the next two numbers identify the position in the sequence of the qualification atthat level; and the last two numbers identify the year in which the qualification was endorsed.(Where qualifications are added after the initial Training Package endorsement, the last twonumbers may differ from other Training Package qualifications as they identify the year inwhich those particular qualifications were endorsed).
Unit of Competency Codes
Within each Training Package, each unit of competency has a unique code. The unit of
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 15 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
competency codes are assigned when the Training Package is endorsed, or when new unitsof competency are added to an existing endorsed Training Package.
A typical code is made up of 12 characters, normally a mixture of uppercase letters andnumbers, as in MCMC210A. The first three characters signify the Training Package (MCM04Competitive Manufacturing Training Package in the above example) and up to eightcharacters, relating to an industry sector, function or skill area, follow. The last character isalways a letter and identifies the unit of competency version. The A in the example aboveindicates that this is the original unit of competency. An incremented version identifier usuallymeans that minor changes have been made. Typically this would mean that wording haschanged in the range statement or evidence guide, providing clearer intent. Where changesare made that alter the outcome, a new code is assigned and the title is changed.
Training Package, Qualification and Unit of Competency Titles
There are agreed conventions for titling Training Packages and their components. Always usethe correct titles, exactly as they appear in the Training Package, and with the code alwaysplaced before the title.
Training Package Titles
The title of each endorsed Training Package is unique and relates the Training Packagesbroad industry coverage.
Qualification Titles
The title of each endorsed Training Package qualification is unique. Qualification titles use thefollowing sequence:
• firstly, the qualification is identified as either Certificate I, Certificate II, Certificate III,Certificate IV, Diploma or Advanced Diploma
• this is followed by the words in for Certificates I to IV and of for Diploma and AdvancedDiploma
• then the industry descriptor follows, for example Telecommunications, and• if applicable, the occupational or functional stream follows in brackets, for example
(Computer Systems).
For example:
• MCM20105 Certificate II in Manufacturing Technology• MCM20205 Certificate II in Competitive Manufacturing
Unit of Competency Titles
Each unit of competency title is unique. Unit of competency titles describe the competencyoutcome concisely, and are written in sentence case.
For example:
• MCMC210A Manage the impact of change on own work• MCMC410A Lead change in a manufacturing environment
Introduction to the Competitive Manufacturing Training PackageThe Competitive Manufacturing Training Package has been developed by the CompetitiveManufacturing Initiative (CMI). The Training Package consists of two volumes, Volume 1 (thisvolume) which contains background, qualifications and assessment information and Volume 2which contains the competency standards.
Overview of CMI
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 16 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
The Competitive Manufacturing Initiative (CMI) was a collaborative response from Australia'sManufacturing Industry Training Advisory Bodies (ITABs) to assist manufacturing industryimprove manufacturing practice through the development of innovative vocational educationand training (VET) qualifications and units of competency. The CMI development process hasbeen funded by funded by ANTA. The original scoping project for the CMI was majorityfunded by industry.
The following ITABs formed the Project Management Group for the initial development of theCMI:
• Automotive Training Australia which covered:• passenger vehicles• trucks• bus and trailer manufacturing• most coach and body building• vehicle repair, service and retail• automotive after market, and• some component manufacturing.
• Light Manufacturing Training Australia which covered:• the textile clothing, footwear and leather industries. and• the furnishing industry.
• Manufacturing Learning Australia which covered process manufacturing industries suchas:• chemical• hydrocarbons• oil• plastics• rubber• cable making• cement• clay• ceramic• concrete• refractories• plaster, and• fibre board.
• Manufacturing Engineering and Related Services ITAB which covered:• metal and engineering related manufacturing• heavy engineering• maintenance• aerospace, and• boating.
• National Food Industry Training Council which covered:• food and beverage• pharmaceutical, and• tobacco processing and manufacturing.
MERS ITAB acted as the secretariat for the development of CMI. However, users should nowcontact Manufacturing Skills Australia (MSA), the national Industry Skills Council that coversmanufacturing to seek specific advice relevant to their area. Contact MSA on ph 02 99555500 or at www.mskills.com.au . The CMI website should also be checked for information andadvice at www.cmi.org.au .
Industry Coverage
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 17 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
The CMI Training Package covers all of the manufacturing industry. At the 2001 census, themanufacturing industry employed 1,010,179 persons or 12% of the entire workforce.Manufacturing is the biggest sector in terms of contribution to gross domestic product where itcontributes 13 % of the total product (Ref: Manufacturing Industry Australia, 1999-2000, ABS,8221.0) and is also the sector with the highest value added contributing 12% of the total value(Ref: Australian System of National Accounts, 2002-2003, ABS, 5204.0) added to theeconomy. The Australian Bureau of Statistics notes (Ref: Manufacturing Industry Australia,1999-2000, ABS 8221.0) that 'Manufacturing contributed more to Australian production...thanany other industry'.
The CMI Training Package is complementary to the existing Training Packages coveringspecific manufacturing sectors. These sector specific Training Packages cover the knowledgeand skills specifically required by those sectors. The CMI Training Package covers knowledgeand skills associated with manufacturing practices and systems which are common acrossmanufacturing sectors.
Development of MCM04
The Development Process
This project originated out of discussions within the Board of the Foundation for AustralianManufacturing Education (FAME) and the initial scoping study was financially supported byFAME, Australian Business Ltd and ANTA. Support for the project's aims and objectives wasalso given by the Australian Manufacturing Centre (AMC) and the Australian Industry Group.This scoping project (Ref: Ratio Pty Ltd/Richard Jenkins & Associates/Sally Davis &Associates Scoping Project for Manufacturing Practice Competencies, Final Report, April2000) found that there was a bias in the then existing Training Packages of specific technicalskills and insufficient coverage of the skills needed to manage, supervise and implementsystem skills needed in modern manufacturing. The scoping report identified a need for thedevelopment of units of competency in manufacturing practice, and possibly alsoqualifications in manufacturing practice.
The CMI Stage 2 project:
• investigated the scope of skills to be included in the CMI• developed a marketing strategy and established a CMI website• established a formal cooperative mechanism amongst the manufacturing ITABs• established a brand and logo based on the title Competitive Manufacturing Initiative
(CMI).
The CMI Stage 3 project then developed and validated a number of units of competency andqualifications. The development and validation was done by consulting industry generally andalso by the use of industry experts. Care was taken through this process to ensure there wasrepresentation of each industry sector and type of manufacturing process. The use ofcompetitive manufacturing practices is variable across the manufacturing sector, and one ofthe aims of developing this Training Package is to make training in these skills more widelyavailable, so helping industry operate more effectively in a competitive environment. Initialconsultation therefore focussed more on identified leaders in this area while validationfocused more on the broader manufacturing industry.
Consultations undertaken as part of CMI Stage 2 and confirmed in Stage 3 indicated that theCMI qualifications and units would represent new content for many RTOs and that many ofthe skills could only be taught and assessed in a workplace environment. CMI Stage 3therefore included a process to allow early identification of delivery issues through a trial siteprocess. Five trial sites were selected to cover both a number of states and also each major
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 18 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
industry sector. The trial sites used (Note: As the units were not endorsed at this stage therewere some practical limitations on the 'use' of these unit) the draft CMI units to map the draftunits to current delivery and to validate the units and to determine any delivery issues. Thetrial sites were:
• Goulburn Ovens Institute of TAFE - Shepparton Campus• Hunter Institute of Technology• Onkaparinga Institute of TAFE• Swinburne University - VET Division• Western Sydney Institute of TAFE - Mt Druitt Campus
The Technology Cadetships
In August 2003 the Australian Industry Group with funding assistance from ANTA establisheda Manufacturing Technician Training Initiative project known colloquially as the TechnologyCadetship Project. The aim of the project was to develop and promote more efficientpathways for school leavers to enter technical occupations in manufacturing industry. One ofthe key objectives was to establish entry level qualifications linked to on and off the jobtraining in a cadetship arrangement.
The origin of the project was partly Australian Industry Group work on the National IndustrySkills Initiative as well as comments and concerns by Ai Group members that pathways forthe development of technician level skills in manufacturing were inefficient and generally tooktoo long to be attractive to either enterprises or young people.
The Ai Group Manufacturing Technician Training Initiative included activities in a number ofareas that were broader than a normal Training Package development project. These areaswere:
• Identification and/or development of appropriate content in existing and/or new TrainingPackages;
• Marketing of technician level contract of employment arrangements to employers, youngpeople, industry and the community generally;
• Establishment of appropriate employment arrangements;• Establishing arrangements for the approval of contracts of employment by State Training
Agencies• Establishment of appropriate funding arrangements for both mainstream training delivery
and employer financial incentives;• Marketing of actual placements to Ai Group members and other employers.
While the Australian Industry Group conducted much of the content research anddevelopment for this submission, both the Ai Group and ANTA realised that Ai Group wouldnot be able to put forward the new qualifications for endorsement under current policyarrangements.
The Australian Industry Group was consulted on the development of the CompetitiveManufacturing Training Package and decided that the CMI was the most appropriate body totake over on a longer term basis the future content development of the Technology Cadetshipand responsibility for endorsement of the work done to date. The CMI ITABs and Ai Groupalso agreed that the qualifications and units for the Technology Cadetship should be part ofthe responsibilities of the Manufacturing Industry Skills Council once it was established.
The Manufacturing Industry Skills Council has now been established and it is anticipated thatthe CMI will continue to exist as a sub committee function in the Manufacturing Skills Counciland that arrangements will be made for on going participation of the Agri-Foods Skills Counciland for automotive industry representation.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 19 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
The term Technology Cadetship was developed to differentiate the level of training from thatcommonly found in apprenticeships and traineeships although the principle of combined offand on the training and mutual obligation of employer and employee is the same.
Awards, Licensing and other Regulatory Issues
Various awards and agreements apply within manufacturing industry. This Training Packagewas designed to allow for these different arrangements. It is appropriate to use this TrainingPackage as part of an award/agreement, but it has not been designed to fit any particularaward or agreement except for the Technology Cadetships.
The Technology Cadetships are designed to work with a variety of employment arrangementsincluding Awards, enterprise agreements and Australian Workplace Agreements in a mannersimilar to apprenticeships and traineeships. However to facilitate early acceptance of theTechnology Cadetship the Australian Industry Group and the Australian ManufacturingWorkers Union (AMWU) have developed a new consent training Award for manufacturingwhich will give a specific employment arrangement option for most manufacturing sectors.This Award will be known as the Manufacturing and Associated Industries Training and SkillsDevelopment Award 2004 and will be presented to the Australian Industrial RelationsCommission as a consent application in the week commencing 8 November 2004.
There are no general licensing issues, however specific licenses may be required in somejobs. The local regulations should be checked for details. The industry is generally subject toa range of regulatory control. These vary with the nature of the facility and to some extent onits location as most regulations are State based and many are enforced by local government.This Training Package allows for these differences without mandating them to specific units ofcompetency which would not be appropriate.
Overview of MCM04 Training Package
General Comments
As MCM04 complements existing manufacturing Training Packages, provision is made in thequalifications for the importation of relevant sector specific units of competency into CMIqualifications. It is also expected that CMI units of competency will be imported into existingmanufacturing Training Packages when they are reviewed, or under continuous improvementprovisions. Not all CMI units of competency may be appropriate for any given sector.
Due to the nature of the CMI, it is expected that most delivery and assessment will be done inpartnership with an enterprise, or group of enterprises, which are embarking on competitivemanufacturing. A project style of delivery is envisaged for many units of competency.
It may be appropriate to grant recognition of current competence (RCC/RPL) for certain FMIunits depending on the amount and type of contextualisation applied to the FMI unit. As theequivalence will depend on the contextualisation applied, it is not possible to give generaladvice at this stage. RCC should be applied on a case by case basis.
Companies embarking on competitive manufacturing will frequently choose different startingpoints, and often different names to describe what they are doing. This Training Packageallows for these differences in approach and relevant units of competency should be selectedto match the starting point and the strategies being adopted.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Overview
Volume 1 of 2 Page 20 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Qualifications Framework
The Australian Qualifications Framework
What is the Australian Qualifications Framework?
A brief overview of the Australian Qualifications Framework (AQF) follows. For a fullexplanation of the AQF see the AQF Implementation Handbook, 3rd Edition 2002. You candownload it from the Australian Qualifications Advisory Board (AQFAB) website (www.aqf.edu.au) or obtain a hard copy by contacting AQFAB on phone 03 9639 1606 or byemailing AQFAB on [email protected]
The AQF provides a comprehensive, nationally consistent framework for all qualifications inpost-compulsory education and training in Australia. In the vocational education and training(VET) sector it assists national consistency for all trainees, learners, employers and providersby enabling national recognition of qualifications and Statements of Attainment.
Training Package qualifications in the VET sector must comply with the titles and guidelines ofthe AQF. Endorsed Training Packages provide a unique title for each AQF qualification whichmust always be reproduced accurately.
Qualifications
Training Packages can incorporate the following eight AQF qualifications.
• Certificate I in ...• Certificate II in ...• Certificate III in ...• Certificate IV in ...• Diploma of ...• Advanced Diploma of ...• Vocational Graduate Certificate of ...• Vocational Graduate Diploma of ...
On completion of the requirements defined in the Training Package, a Registered TrainingOrganisation (RTO) may issue a nationally recognised AQF qualification. Issuance of AQFqualifications must comply with the advice provided in the AQF Implementation Handbookand the Australian Quality Training Framework Standards for Registered TrainingOrganisations, particularly Standard 10.
Statement of Attainment
Where an AQF qualification is partially achieved through the achievement of one or moreendorsed units of competency, an RTO may issue a Statement of Attainment. Issuance ofStatements of Attainment must comply with the advice provided in the AQF ImplementationHandbook and the Australian Quality Training Framework Standards for Registered TrainingOrganisations, particularly Standard 10.
Under the Standards for Registered Training Organisations, RTOs must recognise theachievement of competencies as recorded on a qualification or Statement of Attainmentissued by other RTOs. Given this, recognised competencies can progressively build towardsa full AQF qualification.
AQF Guidelines and Learning Outcomes
The AQF Implementation Handbook provides a comprehensive guideline for each AQFqualification. A summary of the learning outcome characteristics and their distinguishingfeatures for each VET related AQF qualification is provided below.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 21 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Certificate I
Characteristics of Learning Outcomes
Breadth, depth and complexity of knowledge and skills would prepare a person to perform adefined range of activities most of which may be routine and predictable.
Applications may include a variety of employment related skills including preparatory accessand participation skills, broad-based induction skills and/or specific workplace skills. Theymay also include participation in a team or work group.
Distinguishing Features of Learning Outcomes
Do the competencies enable an individual with this qualification to:
• demonstrate knowledge by recall in a narrow range of areas;• demonstrate basic practical skills, such as the use of relevant tools;• perform a sequence of routine tasks given clear direction• receive and pass on messages/information.
Certificate II
Characteristics of Learning Outcomes
Breadth, depth and complexity of knowledge and skills would prepare a person to perform ina range of varied activities or knowledge application where there is a clearly defined range ofcontexts in which the choice of actions required is usually clear and there is limitedcomplexity in the range of operations to be applied.
Performance of a prescribed range of functions involving known routines and proceduresand some accountability for the quality of outcomes.
Applications may include some complex or non-routine activities involving individualresponsibility or autonomy and/or collaboration with others as part of a group or team.
Distinguishing Features of Learning Outcomes
Do the competencies enable an individual with this qualification to:
• demonstrate basic operational knowledge in a moderate range of areas;• apply a defined range of skills;• apply known solutions to a limited range of predictable problems;• perform a range of tasks where choice between a limited range of options is required;• assess and record information from varied sources;• take limited responsibility for own outputs in work and learning.
Certificate III
Characteristics of Learning Outcomes
Breadth, depth and complexity of knowledge and competencies would cover selecting,adapting and transferring skills and knowledge to new environments and providing technicaladvice and some leadership in resolution of specified problems. This would be appliedacross a range of roles in a variety of contexts with some complexity in the extent and choiceof options available.
Performance of a defined range of skilled operations, usually within a range of broaderrelated activities involving known routines, methods and procedures, where some discretionand judgement is required in the section of equipment, services or contingency measures
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 22 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
and within known time constraints.
Applications may involve some responsibility for others. Participation in teams includinggroup or team co-ordination may be involved.
Distinguishing Features of Learning Outcomes
Do the competencies enable an individual with this qualification to:
• demonstrate some relevant theoretical knowledge• apply a range of well-developed skills• apply known solutions to a variety of predictable problems• perform processes that require a range of well-developed skills where some discretion
and judgement is required• interpret available information, using discretion and judgement• take responsibility for own outputs in work and learning• take limited responsibility for the output of others.
Certificate IV
Characteristics of Learning Outcomes
Breadth, depth and complexity of knowledge and competencies would cover a broad rangeof varied activities or application in a wider variety of contexts most of which are complex andnon-routine. Leadership and guidance are involved when organising activities of self andothers as well as contributing to technical solutions of a non-routine or contingency nature.
Performance of a broad range of skilled applications including the requirement to evaluateand analyse current practices, develop new criteria and procedures for performing currentpractices and provision of some leadership and guidance to others in the application andplanning of the skills. Applications involve responsibility for, and limited organisation of,others.
Distinguishing Features of Learning Outcomes
Do the competencies enable an individual with this qualification to:
• demonstrate understanding of a broad knowledge base incorporating some theoreticalconcepts
• apply solutions to a defined range of unpredictable problems• identify and apply skill and knowledge areas to a wide variety of contexts, with depth in
some areas• identify, analyse and evaluate information from a variety of sources• take responsibility for own outputs in relation to specified quality standards• take limited responsibility for the quantity and quality of the output of others.
Diploma
Characteristics of Learning Outcomes
Breadth, depth and complexity covering planning and initiation of alternative approaches toskills or knowledge applications across a broad range of technical and/or managementrequirements, evaluation and co-ordination.
The self directed application of knowledge and skills, with substantial depth in some areaswhere judgement is required in planning and selecting appropriate equipment, services andtechniques for self and others.
Applications involve participation in development of strategic initiatives as well as personal
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 23 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
responsibility and autonomy in performing complex technical operations or organising others.It may include participation in teams including teams concerned with planning and evaluationfunctions. Group or team co-ordination may be involved.
The degree of emphasis on breadth as against depth of knowledge and skills may varybetween qualifications granted at this level.
Distinguishing Features of Learning Outcomes
Do the competencies or learning outcomes enable an individual with this qualification to:
• demonstrate understanding of a broad knowledge base incorporating theoreticalconcepts, with substantial depth in some areas
• analyse and plan approaches to technical problems or management requirements• transfer and apply theoretical concepts and/or technical or creative skills to a range of
situations• evaluate information, using it to forecast for planning or research purposes• take responsibility for own outputs in relation to broad quantity and quality parameters• take some responsibility for the achievement of group outcomes.
Advanced Diploma
Characteristics of Learning Outcomes
Breadth, depth and complexity involving analysis, design, planning, execution and evaluationacross a range of technical and/or management functions including development of newcriteria or applications or knowledge or procedures.
The application of a significant range of fundamental principles and complex techniquesacross a wide and often unpredictable variety of contexts in relation to either varied or highlyspecific functions. Contribution to the development of a broad plan, budget or strategy isinvolved and accountability and responsibility for self and others in achieving the outcomes isinvolved.
Applications involve significant judgement in planning, design, technical orleadership/guidance functions related to products, services, operations or procedures.
The degree of emphasis on breadth as against depth of knowledge and skills may varybetween qualifications granted at this level.
Distinguishing Features of Learning Outcomes
Do the competencies or learning outcomes enable an individual with this qualification to:
• demonstrate understanding of specialised knowledge with depth in some areas• analyse, diagnose, design and execute judgements across a broad range of technical
or management functions• generate ideas through the analysis of information and concepts at an abstract level• demonstrate a command of wide-ranging, highly specialised technical, creative or
conceptual skills• demonstrate accountability for personal outputs within broad parameters• demonstrate accountability for personal and group outcomes within broad parameters.
Vocational Graduate Certificate
Characteristics of competencies or learning outcomes
• The self-directed development and achievement of broad and specialised areas ofknowledge and skills, building on prior knowledge and skills.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 24 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
• Substantial breadth and complexity involving the initiation, analysis, design, planning,execution and evaluation of technical and management functions in highly varied andhighly specialised contexts.
• Applications involve making significant, high-level, independent judgements in majorbroad or planning, design, operational, technical and management functions in highlyvaried and specialised contexts. They may include responsibility and broad rangingaccountability for the structure, management and output of the work or functions ofothers.
• The degree of emphasis on breadth, as opposed to depth, of knowledge and skills mayvary between qualifications granted at this level.
Distinguishing features of learning outcomes
• Demonstrate the self-directed development and achievement of broad and specialisedareas of knowledge and skills, building on prior knowledge and skills.
• Initiate, analyse, design, plan, execute and evaluate major broad or technical andmanagement functions in highly varied and highly specialised contexts.
• Generate and evaluate ideas through the analysis of information and concepts at anabstract level.
• Demonstrate a command of wide-ranging, highly specialised technical, creative orconceptual skills in complex contexts.
• Demonstrate responsibility and broad-ranging accountability for the structure,management and output of the work or functions of others.
Vocational Graduate Diploma
Characteristics of competencies or learning outcomes
• The self-directed development and achievement of broad and specialised areas ofknowledge and skills, building on prior knowledge and skills.
• Substantial breadth, depth and complexity involving the initiation, analysis, design,planning, execution and evaluation of major functions, both broad and highlyspecialised, in highly varied and highly specialised contexts.
• Further specialisation within a systematic and coherent body of knowledge.• Applications involve making high-level, fully independent, complex judgements in broad
planning, design, operational, technical and management functions in highly varied andhighly specialised contexts. They may include full responsibility and accountability forall aspects of work and functions of others, including planning, budgeting and strategydevelopment.
• The degree of emphasis on breadth, as opposed to depth, of knowledge and skills mayvary between qualifications granted at this level.
Distinguishing features of learning outcomes
• Demonstrate the self-directed development and achievement of broad and highlyspecialised areas of knowledge and skills, building on prior knowledge and skills.
• Initiate, analyse, design, plan, execute and evaluate major functions, both broad andwithin highly varied and highly specialised contexts.
• Generate and evaluate complex ideas through the analysis of information and conceptsat an abstract level.
• Demonstrate an expert command of wide-ranging, highly specialised, technical,creative or conceptual skills in complex and highly specialised or varied contexts.
• Demonstrate full responsibility and accountability for personal outputs.• Demonstrate full responsibility and accountability for all aspects of the work or functions
of others, including planning, budgeting and strategy.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 25 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Qualification Pathways for Competitive Manufacturing
The diagram below represents a model of the available qualifications and pathways. Detailsare in the qualifications framework. Contact Manufacturing Skills Australia {www.mskills.com.au } for further details.
Qualification Pathways for Manufacturing Technology
The diagram below represents a model of the available qualifications and pathways. Detailsare in the qualifications framework. Contact Manufacturing Skills Australia {www.mskills.com.au } for further details.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 26 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
General Advice - Competitive Manufacturing Qualifications
Qualifications may be awarded by a Registered Training Organisation (RTO) whencompetencies which meet the specified packaging requirements have been achieved.Competencies achieved which do not combine to make a certificate may be recognised by aStatement of Attainment issued by an RTO.
Competencies have been categorised into systems, change/interpersonal and tools units. TheCertificate III requires a total of 8 units while each of the other qualifications requires a total of10 units/an additional 10 units comprised of:
• a minimum number of MCM systems units from the specified list• a minimum number of MCM change/interpersonal units from the specified list• a minimum number of MCM tools units from the specified list• the balance may be comprised of additional MCM units, or relevant units imported from
another Training Package with a maximum number of imported units per qualification.
For people undertaking a structured learning program in CMI, competency is required inadditional (new) units for each subsequent qualification (see later for details).
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 27 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Entry to any qualification may be at any level. A person can enter a program of training at anylevel.
New Apprenticeships
All Competitive Manufacturing Certificates within this Training Package are potential NewApprenticeships. However these qualifications have been developed primarily for existingmanufacturing workers, especially those working as or likely to become team leaders. For thisreason existing worker New Apprenticeships may be more appropriate than application toschool leavers.
VET in Schools
The delivery and assessment of competencies aligned to AQF 2 under this Training Packagein appropriately designed VET in schools programs is encouraged. However, due to therequirements to demonstrate competency, it would be difficult for a school to assess andaward qualifications within MCM04 except in close partnership with an appropriateorganisation from the industry. The AQTF rules are the overriding requirements in this regard.
The Certificate II in Manufacturing Technology has been developed specifically for use as aVET in schools program.
Prerequisites
Some units of competency have stated prerequisites (these have been kept to a minimum). Inany approved training scheme, it is expected that competency will be attained in theprerequisite units before it is attained in the unit having the prerequisites. Imported units ofcompetency may also have prerequisites which should be observed. In this situation a unitwith two prerequisites will be counted as three units towards the qualification oncecompetency has been attained in all units.
In an assessment of existing competency, it is possible to assess the unit and its prerequisites
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 28 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
together as an integrated assessment. In this situation as well, a unit with two prerequisiteswill be counted as three units towards the qualification once competency has been attained inall units.
Note that the achievement of prerequisite competencies will be recognised for the award ofthe qualification, regardless of the method by which the participant has gained thecompetencies (e.g. prior learning and/or experience). A person entering at AQF 3 andproceeding through the qualifications in an orderly manner might be expected to be assessedon the prerequisites. A person entering at a higher AQF level might expect to be able todemonstrate their competence in the prerequisite in any of a number of ways, including anassessment integrated with the higher unit. RTOs developing formal learning pathways mayfind the prerequisite trail useful in designing a hierarchical learning program, or they maychoose to integrate the prerequisite unit into the higher level unit for purposes of delivery andassessment, or some other approach.
General Advice - Manufacturing Technology Qualifications
The following information sets out units and pathways that can be taken in the Certificate IIIand the Certificate IV in Manufacturing Technology. These qualifications have beendeveloped to be delivered as part of a cadetship contract of training often called a TechnologyCadetship. It is intended at a later date to expand Technology Cadetship related qualificationsinto additional areas and to also develop higher AQF level qualifications.
The units listed for both qualifications are taken from a number of existing Training Packages.These units have been examined for suitability in a cadetship environment and repackaged tosuit entry level technology based training in manufacturing.
Qualifications may be awarded by a Registered Training Organisation (RTO) whencompetencies which meet the specified packaging requirements have been achieved.Competencies achieved which do not combine to make a certificate may be recognised by aStatement of Attainment issued by an RTO.
Structure of Technology Cadetships
The Technology Cadetship related qualifications are very flexible qualifications with aminimum number of core units and pathways that maximise flexibility. The electives havebeen chosen to give entry and operational skills in a wide range of manufacturing technologyapplication areas. Each qualification consists of pathway options. Each pathway indicates theunits that may be taken in that particular pathway. It is intended at a later date to addadditional units and pathways to the qualifications.
Certificate III in Manufacturing Technology
This is comprised of ten units of competency and is normally delivered as part of a one yearTechnology Cadetship. There are two core units that must be completed for all pathways aswell as eight electives.
Certificate IV in Manufacturing Technology
This is comprised of fifteen units of competency and is normally delivered as part of a twoyear Technology Cadetship. There are three core units that must be completed for allpathways.
Pathways
The Certificates III and IV in Manufacturing Technology have the same pathways availablewithin each qualification, with each pathway offering an opportunity for significant choice inelectives. The pathways are:
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 29 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
• CAD/Drafting pathway• Manufacturing Operations pathway• Laboratory Operations pathway• Technical Officer pathway
Reference to these pathways may be included on any qualification statement that is issued.This could be achieved by adding the pathway descriptor below the formal title of thequalification as shown in example 1 or by an additional sentence as shown in example 2below.
Example 1
Certificate III in Manufacturing Technology
Manufacturing Operations pathway
Example 2
Certificate III in Manufacturing Technology
Achieved through the Manufacturing Operations pathway
It should also be noted that a person holding the Metal and Engineering Training PackageCertificate III in Engineering - Technician will satisfy all of the requirements for a Certificate IIIin Manufacturing Technology, and with an additional five units of competency from theparticular pathway chosen will satisfy the requirements for a Certificate IV in ManufacturingTechnology.
Key Competencies
The key competencies for the Certificate III in Manufacturing Technology and the CertificateIV in Manufacturing Technology are described in general terms earlier in this Volume One ofthe Competitive Manufacturing Training Package (MCM04).
The Key Competencies and the Certificate III in Manufacturing Technology
The following describes a typical application of the Key Competencies at Certificate III level.
The Certificate III in Manufacturing Technology qualification is aimed at school leavers whohave completed Year 12 and who will require a level of competence needed to participate asmembers of their team and interact with supervisors and managers. The Certificate III inManufacturing Technology is seen as the beginning of a career pathway in Technician skillsand it is anticipated that many students will complete the qualification and proceed to furtherstudy at the Diploma and the Advanced Diploma level.
Performance level two of the key competencies requires a level of skill to manage activitiesrequiring the selection, application and integration of a number of elements and to select fromestablished criteria to judge quality of process and outcome. This was assessed as the mostappropriate general level for key competency integration at the CMI Certificate III and also theCertificate IV level Manufacturing Technology qualification level. These qualifications aremade up of technician level skills that require exercise of judgement and generally theequivalent of year 12 English, Mathematics and Science ability.
Each individual key competency was also examined to confirm that performance level twowas appropriate for the Certificate III and IV qualifications and any exception to thePerformance Level 2 Key Competency specification is noted.
It also needs to be noted that ' ?the current definitions are problematic. The industry orworkplace context is generally seen as far more indicative in determining the degree ofdifficulty of the application of the Key Competencies than the prescribed and abstracted
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 30 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
performance?' (Ref: Australian National Training Authority, Template for the Print Version of aTraining Package, February 2001, Appendix J) CMI and Technology Cadetship consultationshave confirmed the importance of the workplace context and RTOs should exercise discretionin assessing the level of Key Competencies to integrate into CMI delivery.
1. Collecting, analysing and organising information
The execution of the competencies required for Certificate III always require the collection,analysis and organisation of data/information. A typical application would be a technologycadet who would need to clarify the purpose of a technical test and access and recordinformation from a variety of sources. The person would be assessing information forrelevance, accuracy and completeness in terms of the test to be undertaken. At this level thiswould be performed in accordance with relevant organisation procedures.
2. Communicating ideas and information
The Technology Cadet will be required to adapt modes and styles of communication to suitthe enterprise environment and the purpose of the communication. The cadet will work closelywith supervisors and qualified technicians and will be required to discuss specifications andtechnical processes. At this level this communication would be in accordance withorganisation procedures.
3. Planning and organising activities
Self planning and organising (within an overall framework) is required from all employees in acompetitive manufacturing organisation including Technology Cadets. They will haveresponsibility for achieving objectives and maximising the quality of outcomes or processesconsistent with their level of responsibility and in accordance with procedures.
4. Working with others and in teams
Working in teams is fundamental to the way most competitive manufacturing organisationswork. Teams may be single level work area teams, multidisciplinary, multi-level teams,permanent teams, ad hoc teams or any other combination of people may be termed a 'team'.As the Technology Cadet is in a learning environment within the enterprise working withothers will be the norm.
5. Solving problems
This key competency requires performance level one in the CMI AQF 3 and 4 qualifications.At the Certificate III and IV level problems will typically be related to the process in some way,but may also be interpersonal or other problems. Many of the units focus on particularmethods of identifying and solving problems. At this level the solving of problems would be inaccordance with procedures and outcomes would always be checked with trainers andsupervisors.
6. Using mathematical ideas and techniques
This key competency requires performance level two in the CMI AQF 3 and 4 qualifications.While some units do not require high level mathematical ideas and techniques thequalification as a whole requires skills appropriate to technician level work in manufacturing.This involves in most cases an ability to undertake and interpret tests, formulae ormeasurements that require performance level two mathematical ability.
7. Using technology
Technology cadets will be required to interact with the technology of the enterprise as a majoractivity. Increasingly this technology also includes interaction with digital technology in someway.
At the CMI Certificate III and IV level in a manufacturing organisation a person interprets the
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 31 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
purposes and objectives for the use of technology, and configures and manages a series ofoperations as a process, and selects technological practices to conform with the guidelines forhealth and safety, environmental impact and ethical practice, and uses them within thoseguidelines, and uses technological equipment and material proficiently for the prevailingenvirons and physical capacity. These interactions are in accordance with the procedures ofthe organisation.
Skill Sets
Definition
Skill sets are defined as single units of competency, or combinations of units of competencyfrom an endorsed Training Package, which link to a licence or regulatory requirement, ordefined industry need.
Wording on Statements of Attainment
Skill sets are a way of publicly identifying logical groupings of units of competency which meetan identified need or industry outcome. Skill sets are not qualifications.
Where skill sets are identified in a Training Package, the Statement of Attainment can set outthe competencies a person has achieved in a way that is consistent and clear for employersand others. This is done by including the wording 'these competencies meet [the relevant skillset title or industry need is included]' on the Statement of Attainment. This wording appliesonly to skill sets that are formally identified as such in the endorsed Training Package.
All Statements of Attainment must include the wording 'A Statement of Attainment is issuedby a Registered Training Organisation when an individual has completed one or more units ofcompetency from a nationally recognised qualification'. The following may also be used 'thesecompetencies form part of the [the relevant qualification(s) code and title are inserted]'.
This section below provides information on skill sets within this Training Package, with thefollowing important disclaimer: Readers should ensure that they have also read the part ofthe Training Package that outlines licensing and regulatory requirements.
Skill Sets in this Training Package
Where this section is blank, nationally recognised skill sets have yet to be identified in thisindustry.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Qualifications Framework
Volume 1 of 2 Page 32 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Qualifications
MCM20105 Certificate II in Manufacturing TechnologyThis qualification applies to a learning and assessment environment where access to normalproduction operations is not available. A typical environment will be for application in a VET inSchools delivery environment or other simulated or trial manufacturing environment where ahigh degree of supervision exists. The units are suitable for delivery in a school environmentand for schools to contextualize the units to local manufacturing industry activities.
To be awarded a Certificate II in Competitive Manufacturing, competency must be achieved in10 units chosen from the following three groupings of Core, Manufacturing Practice andManufacturing Technology units of competency. Five are to be completed from the Core andfive completed from across the Manufacturing Technology and Manufacturing Practicegroupings.
Core
All five of the following units must be completed:
Unit code Unit title
MCMO290A Work safely in manufacturing
MCMS200A Apply competitive manufacturing practices
MCMT251A Apply quality standards
MCMT280A Undertake root cause analysis
MCMT271A Use sustainable environmental practices
Elective units (five elective units to be chosen from the two groups below)
Manufacturing practice
At least one of the following units must be completed but up to four may be selected:
Unit code Unit title
MCMS201A Sustain process improvements
MCMC210A Manage the impact of change on own work
MCMT231A Interpret product costs in terms of customer requirements
MCMT250A Monitor process capability
MCMT270A Use sustainable energy practices
Manufacturing Technology
At least one of the following units must be completed but up to four may be selected:
Unit code Unit title
MCMP295A Operate manufacturing equipment
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20105 Certificate II in Manufacturing Technology
Volume 1 of 2, Qualification 1 of 8 Page 33 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMP296A Make a small furniture item from timber
MCMP297A Make an object from cloth using an existing pattern
MCMP298A Make an object from metal
MCMP299A Make an object from plastic
The manufacturing technology units listed above have been specifically developed for theCertificate II in Manufacturing Technology. These units are shown on the following pages ofthis volume.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20105 Certificate II in Manufacturing Technology
Volume 1 of 2, Qualification 1 of 8 Page 34 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20105 Certificate II in Manufacturing Technology
Volume 1 of 2, Qualification 1 of 8 Page 35 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM20205 Certificate II in Competitive ManufacturingTo be awarded a Certificate II in Competitive Manufacturing, competency must be achieved in10 units chosen as specified below.
Core
Three units must be completed:
MCMC210 Manage the impact of change on own work; and
MCMO290 Work safely in manufacturing (or equivalent endorsed OHS unit)
Plus one of
MCMS200 Apply competitive manufacturing practices
MCMS201 Sustain process improvements
Elective units (seven elective units to be chosen from the two groups below)
Competitive Manufacturing elective units
At least two units must be selected from this list:
MCMS200 Apply competitive manufacturing practices ( if not selected in core)
MCMS201 Sustain process improvements ( if not selected in core)
MCMT221 Apply Just in Time (JIT) procedures
MCMT230 Apply cost factors to work practices
MCMT231 Interpret product costs in terms of customer requirements
MCMT240 Implement 5S procedures in a manufacturing environment
MCMT250 Monitor process capability
MCMT251 Apply quality standards
MCMT260 Use planning software systems in manufacturing
MCMT261 Use SCADA systems in manufacturing
MCMT270 Use sustainable energy practices
MCMT271 Use sustainable environmental practices
MCMT280 Undertake basic root cause analysis
MCMT281 Apply a proactive maintenance strategy
General electives
Up to five units may be selected from competitive manufacturing units AQF 2 not alreadyselected or from units that are available at AQF 2 in the following Training Packages or theirsuccessor Training Packages. Any associated prerequisites of those units contribute to the
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20205 Certificate II in Competitive Manufacturing
Volume 1 of 2, Qualification 2 of 8 Page 36 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
total in their own right in arriving at the maximum of five.
• Aeroskills• Automotive Industry Manufacturing• Business Services• Chemical, Hydrocarbons and Oil Refining• Electrotechnology• Food Processing• Furnishing• Laboratory Operations• Manufactured Mineral Products• Metal and Engineering• Plastics, Rubber and Cablemaking• Sugar Milling• Textile Clothing and Footwear Training Package
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20205 Certificate II in Competitive Manufacturing
Volume 1 of 2, Qualification 2 of 8 Page 37 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM20205 Certificate II in Competitive Manufacturing
Volume 1 of 2, Qualification 2 of 8 Page 38 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM30104 Certificate III in Competitive ManufacturingTo be awarded a Certificate III in Competitive Manufacturing, competency must be achievedin 8 units chosen as specified below. At least 3 of these units must be from the 400 series.
MCM Systems
The following MCM Systems unit must be chosen.
MCMS200A Apply competitive manufacturing practices
and one of the following units of competency:
MCMS201A Sustain process improvements
MCMS401A Ensure process improvements are sustained
MCMS405A Lead a manufacturing team using a balanced score card approach
(Only one of MCMS201A, MCMS401A or MCMS405A may be counted towards the CertificateIII)
MCM Change/interpersonal
At least one of the following MCM Change/interpersonal unit must be chosen.
MCMC210A Manage the impact of change on own work
MCMC410A Lead change in a manufacturing environment
MCMC411A Lead a competitive manufacturing team
MCMC413A Lead team culture improvement
(Only one of MCMC210A, MCMC410A, MCMC411A or MCMC413A may be counted towardsthe Certificate III)
MCM Tools
At least one of the following series 400 MCM Tools units must be chosen.
MCMT421A Facilitate a Just in Time (JIT) system
MCMT423A Monitor a manufacturing levelled pull system
MCMT430A Improve cost factors in work practices
MCMT432A Analyse manual handling processes
MCMT440A Lead 5S in a manufacturing environment
MCMT441A Facilitate continuous improvement in manufacturing
MCMT450A Undertake process capability improvements
MCMT451A Mistake proof a production process
MCMT452A Apply statistics to processes in Manufacturing
MCMT453A Use six sigma techniques
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30104 Certificate III in Competitive Manufacturing
Volume 1 of 2, Qualification 3 of 8 Page 39 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT460A Use planning software systems in manufacturing
MCMT461A Facilitate SCADA systems in manufacturing team or work area
MCMT481A Undertake proactive maintenance analyses
MCMT482A Assist in implementing a proactive maintenance strategy
MCMT483A Support proactive maintenance
PMASUP390A Use structured problem solving tools
Other relevant units
No more than four relevant units at the AQF 2, 3 or 4 level may be selected from anotherrelevant endorsed Training Package. Units chosen should be relevant to the workplace andwould normally be drawn from the appropriate sector Training Package, or possibly theBusiness Services Training Package.
Balance of units
Sufficient additional CMI units should be chosen to achieve the required eight units. Thesemay be selected from any of the lists above, or the list below. Remember of the total of eightunits, at least three must be series 400 CMI units.
MCMT220A Apply quick changeover procedures
MCMT221A Apply Just in Time (JIT) procedures
MCMT230A Apply cost factors to work practices
MCMT231A Interpret product costs in terms of customer requirements
MCMT240A Apply 5S procedures in a manufacturing environment
MCMT250A Monitor process capability
MCMT251A Apply quality standards
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
MCMT270A Use sustainable energy practices
MCMT271A Use sustainable environmental practices
MCMT280A Undertake root cause analysis
MCMT281A Contribute to the application of a proactive maintenance strategy
The Key Competencies at Certificate III
The following describes a typical application of the Key Competencies at Certificate III level.
The Certificate III CMI qualification is aimed predominantly at team leaders who will require alevel of competence needed to act as interface between members of their team and
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30104 Certificate III in Competitive Manufacturing
Volume 1 of 2, Qualification 3 of 8 Page 40 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
supervisors and managers. Performance level two of the key competencies requires a level ofskill to manage activities requiring the selection, application and integration of a number ofelements and to select from established criteria to judge quality of process and outcome.
This was assessed as the most appropriate general level for key competency integration atthe CMI Certificate III and also the Certificate IV level as the Certificate IV qualification is alsoaimed at team leaders. Each individual key competency was also examined to confirm thatperformance level two was appropriate for the CMI Certificate III and IV qualifications and anyexception to the Performance Level 2 Key Competency specification is noted.
It also needs to be noted that 'the current definitions are problematic. The industry orworkplace context is generally seen as far more indicative in determining the degree ofdifficulty of the application of the Key Competencies than the prescribed and abstractedperformance'. CMI consultations have confirmed the importance of the workplace context andRTOs should exercise discretion in assessing the level of Key Competencies to integrate intoCMI delivery.
1. Collecting, analysing and organising information
The execution of the competencies required for Certificate III always require the collection,analysis and organisation of data/information. A typical application would be a team leaderwho would need to clarify the information needs of the team and the purposes of theinformation, and access and record information from a variety of sources. The person wouldbe assessing information for relevance, accuracy and completeness in terms of the needs ofhis/her team and immediate supervisors. At this level this would be performed in accordancewith relevant organisation procedures.
2. Communicating ideas and information
Competitive manufacturing organisations often utilise teamwork as a form of workorganisation and require high levels of communication by team leaders with all stakeholders.The team leader will be required to adapt modes and styles of communication to suit theenterprise environment and the purpose of the communication. At this level thiscommunication would be in accordance with organisation procedures.
3. Planning and organising activities
Self planning and organising (within an overall framework) is required from all employees in acompetitive manufacturing organisation. In addition at the Certificate III level they also havesome responsibility for the planning of work and activities more generally and for theorganisation of others. They will have responsibility for achieving objectives and maximisingthe quality of outcomes or processes consistent with their level of responsibility and inaccordance with procedures.
4. Working with others and in teams
Working in teams is fundamental to the way most competitive manufacturing organisationswork. Teams may be single level work area teams, multidisciplinary, multi-level teams,permanent teams, ad hoc teams or any other combination of people may be termed a 'team'.
At the Certificate III level a person will usually have some responsibility for interpretingpurposes and objectives to be achieved by working with others and organises procedures andtimeframes to take account of different roles and perspectives; and works with others toachieve agreed objectives. The work in teams will be in accordance with procedures at thislevel.
5. Solving problems
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30104 Certificate III in Competitive Manufacturing
Volume 1 of 2, Qualification 3 of 8 Page 41 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
In a competitive manufacturing organisation the authority to solve problems is typically moreuniversally held than in other organisations, and effort is invested in equipping all employeesto solve problems.
This key competency requires performance level one in the CMI AQF 3 and 4 qualifications.At the Certificate III and IV level problems will typically be related to the process in some way,but may also be interpersonal or other problems. Many of the 'tools' units focus on particularmethods of identifying and solving problems. At this level the solving of problems would be inaccordance with procedures, following problem solving techniques specified andimplementing solutions defined in the procedures.
6. Using mathematical ideas and techniques
This key competency requires performance level one in the CMI AQF 3 and 4 qualifications.While some units require specific mathematical competence (such as MCMT230, 430, 452)most only require a level of numeracy sufficient to extract data from a simple specificationschart or spreadsheet and understand numbers and interpret what they mean. This is done inaccordance with the procedures.
7. Using technology
Being the manufacturing industry, most employees will be required to interact with thetechnology of the process at least to some extent. Increasingly this technology also includesinteraction with digital technology in some way.
At the CMI Certificate III and IV level in a manufacturing organisation a person interprets thepurposes and objectives for the use of technology, and configures and manages a series ofoperations as a process, and selects technological practices to conform with the guidelines forhealth and safety, environmental impact and ethical practice, and uses them within thoseguidelines, and uses technological equipment and material proficiently for the prevailingenvirons and physical capacity. These interactions are in accordance with the procedures ofthe organisation.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30104 Certificate III in Competitive Manufacturing
Volume 1 of 2, Qualification 3 of 8 Page 42 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30104 Certificate III in Competitive Manufacturing
Volume 1 of 2, Qualification 3 of 8 Page 43 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM30204 Certificate III in Manufacturing TechnologyTo be awarded a Certificate III in Manufacturing Technology, competency must be achievedin 10 units chosen as specified below.
This qualification has four pathways available. These are:
• CAD/Drafting pathway• Manufacturing Operations pathway• Laboratory Operations pathway• Technical Officer pathway
Each pathway offers an opportunity for significant choice in electives and each pathwayrequires the same core units to be completed.
Note: The minimum requirements for the Certificate III in Manufacturing Technology can alsobe met by holders of the Metal and Engineering Training Package Certificate III inEngineering - Technician.
Core units
The following two units must be chosen:
Unit code Unit title
MCMT251A Apply quality standards
MEM30.12A Apply mathematical techniques in a manufacturing engineering or relatedenvironment
Elective units for CAD/drafting pathway
At least eight elective units, including up to two free electives, must be chosen:
Unit code Unit title
AUM4003A Interpret customer requirements
LMTPRGN05A Participate in product engineering
MEM12.24 Perform computations
MEM16.6A Organise and communicate information
MEM16.8A Interact with computing technology
MEM30.1A Use computer aided design systems to produce basic engineering drawings*
MEM30.2A Produce basic engineering graphics *
MEM30.3A Produce engineering drawings *
MEM30.4A Use CAD to create and display 3D models *
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to evaluate engineering
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 44 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
applications
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.13A Assist in the preparation of a basic workplace layout
MEM30.25A Analyse a simple electrical system circuit*
Free electives: Up to two of the eight elective units of competency may also be chosenfrom the free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusionat Certificate III.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for manufacturing operations pathway
At least eight elective units, including up to two free electives, must be chosen:
Unit code Unit title
FDFOPTSD2A Work in a socially diverse environment
MCMS200A Apply competitive manufacturing practices
MCMS201A Sustain process improvements
MCMS401A Ensure process improvements are sustained
MCMT220A Apply quick changeover procedures
MCMT230A Apply cost factors to work practices
MCMT231A Interpret product costs in terms of customer requirements
MCMT250A Monitor process capability
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
MCMT280A Undertake root cause analysis
MCMT430A Improve cost factors in work practices
MEM15.1B Perform basic statistical quality control
MEM16.6A Organise and communicate information
MEM16.8A Interact with computing technology
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 45 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MEM30.14A Apply basic just in time systems to the reduction of waste
MEM30.15A Develop recommendations for basic set up time improvements
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.21A Prepare a simple production schedule
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
Freeelectives:
Up to two of the eight elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate III.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for laboratory operations pathway
At least eight elective units, including up to two free electives, must be chosen:
Unit code Unit title
LMTPDTX04A Contribute to the development of products or processes
MEM15.1B Perform basic statistical quality control
MEM16.6A Organise and communicate information
MEM16.8A Interact with computing technology
MEM30.12A Apply mathematical techniques in a manufacturing engineering or relatedenvironment
MEM30.24A Participate in quality assurance techniques *
PMLCOM300B Communicate with other people
PMLDATA200A Record and present data
PMLMAIN300B Maintain the laboratory fit for purpose
PMLOHS301B Work safely with instruments that emit ionising radiation
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 46 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
PMLOHS302A Participate in laboratory/field workplace safety
PMLORG301A Plan and conduct laboratory/field work
PMLQUAL300B Contribute to the achievement of quality objectives
PMLQUAL301B Apply critical control point requirements
PMLQUAL401B Apply quality system and continuous improvement processes
PMLSAMP200A Collect routine site samples
PMLSAMP201A Handle and transport samples or equipment
PMLSAMP302A Receive and prepare samples for testing
PMLSAMP400B Obtain representative samples in accordance with sampling plan
PMLSCIG300B Operate basic handblowing equipment
PMLSCIG301B Repair glass apparatus using simple glassblowing equipment
PMLTEST300B Perform basic tests
PMLTEST303B Prepare working solutions
PMLTEST304B Prepare culture media
PMLTEST305B Perform aseptic techniques
PMLTEST306B Assist with fieldwork
PMLTEST307B Prepare trial batches for evaluation
PMLTEST308A Perform microscopic examination
Freeelectives:
Up to two of the eight elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate III.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for technical officer pathway
At least eight elective units, including up to two free electives, must be chosen:
Unit code Unit title
LMTPDTX04A Contribute to the development of products or processes
MCMT231A Interpret product costs in terms of customer requirements
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 47 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
MCMT270A Use sustainable energy practices
MCMT270A Use sustainable energy practices
MCMT280A Undertake root cause analysis
MCMT432A Analyse manual handling processes
MEM15.1B Perform basic statistical quality control
MEM16.6A Organise and communicate information
MEM16.8A Interact with computing technology
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to engineering designs andapplications
MEM30.9A Contribute to the design of basic mechanical systems*
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.13A Assist in the design of basic workplace layout
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.22A Undertake supervised procurement activities
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
Freeelectives:
Up to two of the eight elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate III.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 48 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Free electives bank for the MCM30204 Certificate III in Manufacturing Technology
Unit code Unit title
AUM4003A Interpret customer requirements
MEM30.1A Use computer aided design systems to produce basic engineeringdrawings
MEM30.2A Produce basic engineering graphics
MEM30.3A Produce engineering drawings
MEM30.4A Use CAD to create and display 3D models
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to engineering designs andapplications
MEM30.9A Contribute to the design of basic mechanical systems*
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.13A Assist in the preparation of a basic workplace layout
MEM30.14A Apply basic just in time systems to the reduction of waste
MEM30.15A Develop recommendations for basic set up time improvements
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.21A Prepare a simple production schedule
MEM30.22A Undertake supervised procurement activities
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
MEM30.25A Analyse a simple electrical system circuit
MCMS200A Apply competitive manufacturing practices
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 49 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMS201A Sustain process improvements
MCMS401A Ensure process improvements are sustained
MCMT220A Apply quick changeover procedures
MCMT230A Apply cost factors to work practices
MCMT231A Interpret product costs in terms of customer requirements
MCMT250A Monitor process capability
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
MCMT270A Use sustainable energy practices
MCMT280A Undertake root cause analysis
MCMT430A Improve cost factors in work practices
MCMT432A Analyse manual handling processes
FDFOPTSD2A Work in a socially diverse environment
PMLCOM300B Communicate with other people
PMLDATA200A Record and present data
PMLMAIN300B Maintain the laboratory fit for purpose
PMLOHS302A Participate in laboratory/field workplace safety
PMLOHS301B Work safely with instruments that emit ionising radiation
PMLORG301A Plan and conduct laboratory/field work
PMLQUAL300B Contribute to the achievement of quality objectives
PMLQUAL301B Apply critical control point requirements
PMLQUAL401B Apply quality system and continuous improvement processes
PMLSAMP200A Collect routine site samples
PMLSAMP201A Handle and transport samples or equipment
PMLSAMP302A Receive and prepare samples for testing
PMLSAMP400B Obtain representative samples in accordance with sampling plan
PMLSCIG300B Operate basic handblowing equipment
PMLSCIG301B Repair glass apparatus using simple glassblowing equipment
PMLTEST300B Perform basic tests
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 50 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
PMLTEST303B Prepare working solutions
PMLTEST304B Prepare culture media
PMLTEST305B Perform aseptic techniques
PMLTEST306B Assist with fieldwork
PMLTEST307B Prepare trial batches for evaluation
PMLEST308A Perform microscopic examination
LMTPRGN05A Participate in product engineering
LMTPDTX04A Contribute to the development of products or processes
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 51 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM30204 Certificate III in Manufacturing Technology
Volume 1 of 2, Qualification 4 of 8 Page 52 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM40104 Certificate IV in Competitive ManufacturingTo be awarded a Certificate IV in Competitive Manufacturing, competency must be achievedin 10 units chosen as specified below. Holders of the Certificate III need to ensure that theyhave at least three additional series 400 units to any they may have gained competence in aspart of the Certificate III.
MCM Systems
At least one of the following MCM Systems units must be chosen.
MCMS400A Implement a competitive manufacturing system
MCMS401A Ensure process improvements are sustained
MCMS405A Lead a manufacturing team using a balanced score card approach
MCM Change/interpersonal
The following MCM Change/interpersonal unit must be chosen.
MCMC410A Lead change in a manufacturing environment
And one of the following units of competency:
MCMC411A Lead a competitive manufacturing team
MCMC413A Lead team culture improvement
MCM Tools
At least two of the following MCM Tools units must be chosen.
MCMT421A Facilitate a Just in Time (JIT) system
MCMT423A Monitor a manufacturing levelled pull system
MCMT430A Improve cost factors in work practices
MCMT432A Analyse manual handling processes
MCMT440A Lead 5S in a manufacturing environment
MCMT441A Facilitate continuous improvement in manufacturing
MCMT450A Undertake process capability improvements
MCMT451A Mistake proof a production process
MCMT452A Apply statistics to processes in manufacturing
MCMT453A Use six sigma techniques
MCMT460A Use planning software systems in manufacturing
MCMT461A Facilitate SCADA systems in manufacturing team or work area
MCMT481A Undertake proactive maintenance analyses
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40104 Certificate IV in Competitive Manufacturing
Volume 1 of 2, Qualification 5 of 8 Page 53 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT482A Assist in implementing a proactive maintenance strategy
MCMT483A Support proactive maintenance
PMASUP390A Use structured problem solving tools
Other relevant units
No more than four relevant units at the AQF 3, 4 or 5 level may be selected from anotherrelevant endorsed Training Package. Units chosen should be relevant to the workplace andwould normally be drawn from the appropriate sector Training Package, or possibly theBusiness Services Training Package.
Balance of units
Sufficient additional units should be chosen from the CMI units to achieve the required tenunits.
The Key Competencies at Certificate IV
The Key Competencies at this level have been described in the preceding section on the CMICertificate III. This is because the two qualifications are aimed at the same broad target groupwith the CMI Certificate IV being a more comprehensive qualification.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40104 Certificate IV in Competitive Manufacturing
Volume 1 of 2, Qualification 5 of 8 Page 54 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40104 Certificate IV in Competitive Manufacturing
Volume 1 of 2, Qualification 5 of 8 Page 55 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM40204 Certificate IV in Manufacturing TechnologyTo be awarded a Certificate IV in Manufacturing Technology, competency must be achievedin 15 units chosen as specified below.
This qualification has four pathways available. These are:
• CAD/Drafting pathway• Manufacturing Operations pathway• Laboratory Operations pathway• Technical Officer pathway
Each pathway offers an opportunity for significant choice in electives and each pathwayrequires the same core units to be completed.
Note: The minimum requirements for the Certificate IV in Manufacturing Technology can alsobe met by holders of the Metal and Engineering Training Package Certificate III inEngineering - Technician who complete five additional units of competency from the bank ofunits for the particular pathway chosen.
Core units
The following three units must be chosen:
Unit code Unit title
MCMT251A Apply quality standards
MEM30.12A Apply mathematical techniques in a manufacturing engineering or relatedenvironment
MEM16.8A Interact with computing technology
Elective units for CAD/drafting pathway
At least twelve elective units, including up to two free electives, must be chosen:
Unit code Unit title
AUM4003A Interpret Customer Requirements
LMTPRGN05A Participate in product engineering
MCMS201A Sustain process improvements
MCMT230A Apply cost factors to work practices
MEM12.24A Perform computations
MEM16.6A Organise and communicate information
MEM30.1A Use computer aided design systems to produce basic engineeringdrawings *
MEM30.2A Produce basic engineering graphics*
MEM30.3A Produce engineering drawings*
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 56 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MEM30.4A Use CAD to create and display 3D models*
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to evaluate engineeringapplications
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.13A Assist in the preparation of a basic workplace layout
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.25A Analyse a simple electrical system circuit*
UTPNEG147A Perform electrical/electronic drafting
Freeelectives:
Up to two of the twelve elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate IV.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for manufacturing operations pathway
At least twelve elective units, including up to two free electives, must be chosen:
Unit code Unit title
FDFOPTSD2A Work in a socially diverse environment
MEM15.1B Perform basic statistical quality control
MEM16.6A Organise and communicate information
MEM30.14A Apply basic just in time systems to the reduction of waste
MEM30.15A Develop recommendations for basic set up time improvements
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 57 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.21A Prepare a simple production schedule
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
MCMS201A Sustain process improvements
MCMT280A Undertake root cause analysis
MCMS401A Ensure process improvements are sustained
MCMT230A Apply cost factors to work practices
MCMT430A Improve cost factors in work practices
MCMT231A Interpret product costs in terms of customer requirements
MCMT250A Monitor process capability
MCMS200A Apply competitive manufacturing practices
MCMT220A Apply quick changeover procedures
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
Freeelectives:
Up to two of the twelve elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate IV.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for laboratory operations pathway
At least twelve elective units must be chosen:
Unit code Unit title
LMTPDTX04A Contribute To the Development of Products or Processes
MEM30.12A Apply mathematical techniques in a manufacturing engineering or relatedenvironment
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.24A Participate in quality assurance techniques*
MCMT261A Use SCADA systems in manufacturing
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 58 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT270A Use sustainable energy practices
PMLDATA200A Record and present data
PMLSAMP200A Collect routine site samples
PMLSAMP201A Handle and transport samples or equipment
PMLSAMP300A Receive and prepare samples for testing
PMLTEST300B Perform basic tests
PMLTEST308A Perform microscopic examination
PMLTEST303B Prepare working solutions
PMLTEST304B Prepare culture media
PMLTEST305B Perform aseptic techniques
PMLTEST306B Assist with fieldwork
PMLTEST307B Prepare trial batches for evaluation
PMLMAIN300B Maintain the laboratory fit for purpose
PMLOHS302A Participate in laboratory/field workplace safety
PMLOHS301B Work safely with instruments that emit ionising radiation
PMLQUAL300B Contribute to the achievement of quality objectives
PMLQUAL301B Apply critical control point requirements
PMLSCIG300B Operate basic handblowing equipment
PMLSCIG301B Repair glass apparatus using simple glassblowing equipment
PMLCOM300B Communicate with other people
PMLORG301A Plan and conduct laboratory/field work
PMLSAMP400B Obtain representative samples in accordance with sampling plan
PMLTEST402B Prepare, standardise and use solutions
PMLTEST403B Assist with geotechnical site investigations
PMLTEST404A Perform chemical tests and procedures
PMLQUAL400B Contribute to the ongoing development of HACCP plans
PMLQUAL401B Apply quality system and continuous improvement processes
Freeelectives:
Up to two of the twelve elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion at
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 59 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Certificate IV.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Elective units for technical officer pathway
At least twelve elective units, including up to two free electives, must be chosen:
Unit code Unit title
LMTPDTX-04AContribute to the development of products or processes
MEM15.1B Perform basic statistical quality control
MEM16.6A Organise and communicate information
MEM30.1A Use computer aided design systems to produce basic engineering drawings*
MEM30.2A Produce basic engineering graphics*
MEM30.3A Produce engineering drawings*
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to engineering designs andapplications
MEM30.9A Contribute to the design of basic mechanical systems*
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.13A Assist in the design of basic workplace layout
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.22A Undertake supervised procurement activities
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
MCMT231A Interpret product costs in terms of customer requirements
MCMT260A Use planning software systems in manufacturing
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 60 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT261A Use SCADA systems in manufacturing
MCMT270A Use sustainable energy practices
MCMT280A Undertake root cause analysis
MCMT432A Analyse manual handling processes
Freeelectives:
Up to two of the twelve elective units of competency may also be chosen fromthe free electives bank listed at the end of the pathways or any otherendorsed Training Packages where those units are available for inclusion atCertificate IV.
Prerequisites: Units marked with an asterisk have a prerequisite requirement. Theprerequisites for these units should be counted in the total number of unitsrequired in the elective group. Please refer to the prerequisite table in thisdocument.
Free electives bank for the MCM40204 Certificate IV in Manufacturing Technology
Unit code Unit title
AUM4003A Interpret customer requirements
FDFOPTSD2A Work in a socially diverse environment
LMTPDTX-04A Contribute to the development of products or processes
LMTPRGN05A Participate in product engineering
MEM30.1A Use computer aided design systems to produce basic engineeringdrawings
MEM30.2A Produce basic engineering graphics
MEM30.3A Produce engineering drawings
MEM30.4A Use CAD to create and display 3D models
MEM30.7A Select common engineering materials
MEM30.8A Apply basic economic and ergonomic concepts to evaluate engineeringapplications
MEM30.9A Contribute to the design of basic mechanical systems*
MEM30.10A Set up basic hydraulic circuits
MEM30.11A Set up basic pneumatic circuits
MEM30.12A Apply mathematical techniques in a manufacturing engineering or relatedenvironment
MEM30.13A Assist in the preparation of a basic workplace layout
MEM30.14A Apply basic just in time systems to the reduction of waste
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 61 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MEM30.15A Develop recommendations for basic set up time improvements
MEM30.16A Assist in the analysis of a supply chain
MEM30.17A Use basic preventative maintenance techniques and tools
MEM30.18A Undertake basic process planning
MEM30.19A Use resource planning software systems in manufacturing*
MEM30.20A Develop and manage a plan for a simple manufacturing related project
MEM30.21A Prepare a simple production schedule
MEM30.22A Undertake supervised procurement activities
MEM30.23A Prepare a simple cost estimate for a manufactured product
MEM30.24A Participate in quality assurance techniques*
MEM30.25A Analyse a simple electrical system circuit*
MCMS201A Sustain process improvements
MCMS200A Apply competitive manufacturing practices
MCMS201A Sustain process improvements
MCMS401A Ensure process improvements are sustained
MCMT220A Apply quick changeover procedures
MCMT230A Apply cost factors to work practices
MCMT231A Interpret product costs in terms of customer requirements
MCMT250A Monitor process capability
MCMT260A Use planning software systems in manufacturing
MCMT261A Use SCADA systems in manufacturing
MCMT270A Use sustainable energy practices
MCMT280A Undertake root cause analysis
MCMT430A Improve cost factors in work practices
MCMT432A Analyse manual handling processes
PMLCOM300B Communicate with other people
PMLDATA200A Record and present data
PMLMAIN300B Maintain the laboratory fit for purpose
PMLOHS301B Work safely with instruments that emit ionising radiation
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 62 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
PMLOHS302A Participate in laboratory/field workplace safety
PMLORG301A Plan and conduct laboratory/field work
PMLQUAL300B Contribute to the achievement of quality objectives
PMLQUAL301B Apply critical control point requirements
PMLQUAL400B Contribute to the ongoing development of HACCP plans
PMLQUAL401B Apply quality system and continuous improvement processes
PMLSAMP200A Collect routine site samples
PMLSAMP201A Handle and transport samples or equipment
PMLSAMP302A Receive and prepare samples for testing
PMLSAMP400B Obtain representative samples in accordance with sampling plan
PMLSCIG300B Operate basic handblowing equipment
PMLSCIG301B Repair glass apparatus using simple glassblowing equipment
PMLTEST300B Perform basic tests
PMLTEST303B Prepare working solutions
PMLTEST304B Prepare culture media
PMLTEST305B Perform aseptic techniques
PMLTEST306B Assist with fieldwork
PMLTEST307B Prepare trial batches for evaluation
PMLTEST308A Perform microscopic examination
PMLTEST402B Prepare, standardise and use solutions
PMLTEST403B Assist with geotechnical site investigations
PMLTEST404A Perform chemical tests and procedures
UTPNEG147A Perform electrical/electronic drafting
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 63 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM40204 Certificate IV in Manufacturing Technology
Volume 1 of 2, Qualification 6 of 8 Page 64 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM50104 Diploma of Competitive ManufacturingTo be awarded a Diploma of Competitive Manufacturing, competency must be achieved in atotal of 20 units comprised of the 10 units required for a Certificate IV and a further 10 chosenas specified below.
MCM Systems
At least one of the following MCM Systems units must be chosen.
MCMS600A Develop a competitive manufacturing system
MCMS601A Analyse and map a value chain
MCMS602A Manage a value chain
MCMS603A Develop manufacturing related business plans
MCMS604A Manage competitive manufacturing processes in a jobbing shopenvironment
MCMS605A Develop a balanced score card for use in competitive manufacturing
MCMS606A Introduce competitive manufacturing to a small or medium enterprise
MCM Change/interpersonal
At least one of the following MCM Change/interpersonal units must be chosen.
MCMC610A Manage relationships with non-customer external organisations
MCMC611A Manage people relationships
MCMC612A Manage workplace learning
MCMC613A Facilitate holistic culture improvement in a manufacturing enterprise
MCMC614A Develop a communications strategy to support production
MCM Tools
At least two of the following MCM Tools units must be chosen.
MCMT452A Apply statistics to processes in manufacturing
MCMT620A Develop quick changeover procedures
MCMT621A Develop a Just in Time (JIT) system
MCMT622A Design a process layout
MCMT623A Develop a levelled pull system of manufacturing
MCMT630A Optimise cost of product
MCMT631A Undertake value analysis of product costs in terms of customer requirements
MCMT632A Analyse cost implications of maintenance strategy
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM50104 Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 7 of 8 Page 65 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT640A Manage 5S system in a manufacturing environment
MCMT641A Implement a continuous improvement system
MCMT650A Determine and improve process capability
MCMT652A Design an experiment
MCMT653A Apply six sigma to process control and improvement
MCMT660A Develop the application of enterprise systems in manufacturing
MCMT661A Determine and establish information collection requirements and processes
MCMT662A Develop a documentation control strategy for a manufacturing enterprise
MCMT670A Develop and manage sustainable energy practices
MCMT671A Develop and manage sustainable environmental practices
MCMT675A Facilitate the development of a new product
MCMT681A Develop a proactive maintenance strategy
MCMT682A Adapt a proactive maintenance strategy to the process manufacturing sector
MCMT683A Adapt a proactive maintenance strategy for a seasonal or cyclicalmanufacturing operation
Other relevant units
No more than four relevant units at the AQF 4, 5 or 6 level may be selected from anotherrelevant endorsed Training Package. Units chosen should be relevant to the workplace andwould normally be drawn from the appropriate sector Training Package, or possibly theBusiness Services Training Package.
Balance of units
Sufficient additional units should be chosen from the CMI units to achieve the required tenunits.
The Key Competencies at Diploma level
The following describes a typical application of the Key Competencies at Diploma level. TheDiploma level qualification is targeted at supervisors seeking a comprehensive training inmanaging manufacturing practice systems.
The competencies used at Diploma level predominantly require a level of competence neededto evaluate and sometimes reshape tasks. The Key Competencies for the Diploma level areat performance level 3. Any exceptions to this are noted below.
However it also needs to be noted that 'the current definitions are problematic. The industry orworkplace context is generally seen as far more indicative in determining the degree ofdifficulty of the application of the Key Competencies than the prescribed and abstractedperformance.'
1. Collecting, analysing and organising information
The execution of the competencies required for the Diploma always requires the collection,
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM50104 Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 7 of 8 Page 66 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
analysis and organisation of data/information. At this level there is often the need todetermine what data is needed and then to evaluate whether the data collected will yield therequired information. At this level this would be in accordance with protocols and policies andmay be covered by procedures.
2. Communicating ideas and information
Competitive manufacturing organisations usually work in teams and require high levels ofcommunication with all stakeholders. At this level there is the need to evaluate theeffectiveness of communication flows and whether the information is appropriate for thedecisions which need to be made and then making, or recommending changes. At this levelthis would be in accordance with protocols and policies and may be covered by procedures.
3. Planning and organising activities
At the Diploma level, not only is planning and organisation of self, others and resourcesundertaken, but there is an expectation that the effectiveness of these plans and organisingwill be evaluated and where appropriate changed/recommendations for change made. At thislevel this would be in accordance with protocols and policies and may be covered byprocedures.
4. Working with others and in teams
Working in teams is fundamental to the way most competitive manufacturing organisationswork. At this level the function of the teams and other interpersonal interactions should bebeing evaluated and improvements being made. At this level this would be in accordance withprotocols and policies and may be covered by procedures.
5. Solving problems
Problem solving is a key activity at this level with the need to evaluate the tools needed tosolve problems and then to modify the tools or acquire/recommend other tools to help theproblem solving process. At the Diploma level the person might be expected to have a widearray of problem solving tools to choose from. At this level this would be in accordance withprotocols and policies and may be covered by procedures. They might also be expected togenerate novel solutions to problems which do not respond to standard solutions, possiblyworking with relevant technical experts.
6. Using mathematical ideas and techniques
While some units require specific mathematical competence (such as MCMT452, 630, 631,650) most require a level of numeracy sufficient to understand numerical data/charts, interpretwhat they mean and communicate with technical experts about quantitative data. At this levelthis would be in accordance with protocols and policies and may be covered by procedures.
7. Using technology
At this level hands on competency with the technology of the process may not be required;however an understanding of the principles underpinning the manufacturing process will berequired sufficient to evaluate its operation and to evaluate different courses of action whileworking with a technical expert. Computer usage would be expected. At this level this wouldbe in accordance with protocols and policies and may be covered by procedures.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM50104 Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 7 of 8 Page 67 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM50104 Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 7 of 8 Page 68 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM60104 Advanced Diploma of Competitive ManufacturingTo be awarded an Advanced Diploma of Competitive Manufacturing, competency must beachieved in 30 units comprised of the 10 units required for a Certificate IV and a further 20units chosen as specified below.
MCM Systems
At least two of the following MCM Systems units must be chosen.
MCMS600A Develop a competitive manufacturing system
MCMS601A Analyse and map a value chain
MCMS602A Manage a value chain
MCMS603A Develop manufacturing related business plans
MCMS604A Manage competitive manufacturing processes in a jobbing shopenvironment
MCMS605A Develop a balanced score card for use in competitive manufacturing
MCMS606A Introduce competitive manufacturing to a small or medium enterprise
MCM Change/interpersonal
At least two units of the following MCM Change/interpersonal units must be chosen.
MCMC610A Manage relationships with non-customer external organisations
MCMC611A Manage people relationships
MCMC612A Manage workplace learning
MCM613A Facilitate holistic culture improvement in a manufacturing enterprise
MCM614A Develop a communications strategy to support production
MCM Tools
At least four units of the following MCM Tools units must be chosen.
MCMT452A Apply statistics to processes in manufacturing
MCMT620A Develop quick changeover procedures
MCMT621A Develop a Just in Time (JIT) system
MCMT622A Design a process layout
MCMT623A Develop a levelled pull system of manufacturing
MCMT630A Optimise cost of product
MCMT631A Undertake value analysis of product costs in terms of customer requirements
MCMT632A Analyse cost implications of maintenance strategy
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM60104 Advanced Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 8 of 8 Page 69 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCMT640A Manage 5S system in a manufacturing environment
MCMT641A Implement a continuous improvement system
MCMT650A Determine and improve process capability
MCMT652A Design an experiment
MCMT653A Apply six sigma to process control and improvement
MCMT660A Develop the application of enterprise systems in manufacturing
MCMT661A Determine and establish information collection requirements and processes
MCMT662A Develop a documentation control strategy for a manufacturing enterprise
MCMT670A Develop and manage sustainable energy practices
MCMT671A Develop and manage sustainable environmental practices
MCMT675A Facilitate the development of a new product
MCMT681A Develop a proactive maintenance strategy
MCMT682A Adapt a proactive maintenance strategy to the process manufacturing sector
MCMT683A Adapt a proactive maintenance strategy for a seasonal or cyclicalmanufacturing operation
Other relevant units
No more than eight relevant units at the AQF 4, 5 or 6 level may be selected from anotherrelevant endorsed Training Package. Units chosen should be relevant to the workplace andwould normally be drawn from the appropriate sector Training Package, or possibly theBusiness Services Training Package.
Balance of units
Sufficient additional units should be chosen from the CMI units to achieve the required twentyunits (plus 10 units from the Certificate IV).
The Key Competencies at Advanced Diploma level
The following describes a typical application of the Key Competencies at Advanced Diplomalevel.
The competencies used at Advanced Diploma level predominantly require a level ofcompetence needed to evaluate and reshape tasks. Key Competencies are required atperformance level 3.
However it needs to be noted that 'the current definitions are problematic. The industry orworkplace context is generally seen as far more indicative in determining the degree ofdifficulty of the application of the Key Competencies than the prescribed and abstractedperformance.'
1. Collecting, analysing and organising information
The execution of the competencies required for the Advanced Diploma always requires thecollection, analysis and organisation of data/information. At this level there is often the need
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM60104 Advanced Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 8 of 8 Page 70 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
to determine what data is needed and then to evaluate whether the data collected will yieldthe required information. At this level this would be in accordance with protocols and policiesand may be covered by procedures.
2. Communicating ideas and information
Competitive manufacturing organisations usually work in teams and require high levels ofcommunication with all stakeholders. At this level there is the need to evaluate theeffectiveness of communication flows and whether the information is appropriate for thedecisions which need to be made and then making, or recommending changes. At this levelthis would be in accordance with protocols and policies and may be covered by procedures.
3. Planning and organising activities
At the Advanced Diploma level, not only is planning and organisation of self, others andresources undertaken, but there is an expectation that the effectiveness of these plans andorganising will be evaluated and where appropriate changed/ recommendations for changemade. At this level this would be in accordance with protocols and policies and may becovered by procedures.
4. Working with others and in teams
Working in teams is fundamental to the way most competitive manufacturing organisationswork. At this level the function of the teams and other interpersonal interactions should bebeing evaluated and improvements being made. At this level this would be in accordance withprotocols and policies and may be covered by procedures.
5. Solving problems
Problem solving is a key activity at this level with the need to evaluate the tools needed tosolve problems and then to modify the tools or acquire/recommend other tools to help theproblem solving process. At the Advanced Diploma level the person might be expected tohave an extensive array of problem solving tools to choose from. At this level this would be inaccordance with protocols and policies and may be covered by procedures. They might alsobe expected to generate novel solutions to problems which do not respond to standardsolutions, possibly working with relevant technical experts.
6. Using mathematical ideas and techniques
While some units require specific mathematical competence (such as MCMT452, 630, 631,650) most require a level of numeracy sufficient to understand numerical data/charts, interpretwhat they mean and communicate with technical experts about quantitative data. At this levelthis would be in accordance with protocols and policies and may be covered by procedures.
7. Using technology
At this level hands on competency with the technology of the process may not be required,however an understanding of the principles underpinning the manufacturing process will berequired sufficient to evaluate its operation and to evaluate different courses of action whileworking with a technical expert. Computer usage would be expected. At this level this wouldbe in accordance with protocols and policies and may be covered by procedures.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM60104 Advanced Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 8 of 8 Page 71 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007
MCM60104 Advanced Diploma of Competitive Manufacturing
Volume 1 of 2, Qualification 8 of 8 Page 72 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Assessment Guidelines
Introduction
These Assessment Guidelines provide the endorsed framework for assessment of units ofcompetency in this Training Package. They are designed to ensure that assessment isconsistent with the Australian Quality Training Framework (AQTF) Standards for RegisteredTraining Organisations. Assessments against the units of competency in this TrainingPackage must be carried out in accordance with these Assessment Guidelines.
Assessment System Overview
This section provides an overview of the requirements for assessment when using thisTraining Package, including a summary of the AQTF requirements; licensing/registrationrequirements; and assessment pathways.
Benchmarks for Assessment
Assessment within the National Training Framework is the process of collecting evidence andmaking judgements about whether competency has been achieved to confirm whether anindividual can perform to the standards expected in the workplace, as expressed in therelevant endorsed unit of competency.
In the areas of work covered by this Training Package, the endorsed units of competency arethe benchmarks for assessment. As such, they provide the basis for nationally recognisedAustralian Qualifications Framework (AQF) qualifications and Statements of Attainmentissued by Registered Training Organisations (RTOs).
Australian Quality Training Framework Assessment Requirements
Assessment leading to nationally recognised AQF qualifications and Statements ofAttainment in the vocational education and training sector must meet the requirements of theAQTF as expressed in the Standards for Registered Training Organisations.
The Standards for Registered Training Organisations can be downloaded from the DESTwebsite at www.dest.gov.au or can be obtained in hard copy from DEST. The following pointssummarise the assessment requirements under the AQTF.
Registration of Training Organisations
Assessment must be conducted by, or on behalf of, an RTO formally registered by a State orTerritory Registering/Course Accrediting Body in accordance with the Standards forRegistered Training Organisations. The RTO must have the specific units of competencyand/or AQF qualifications on its scope of registration. See Section 1 of the Standards forRegistered Training Organisations.
Quality Training and Assessment
Each RTO must have systems in place to plan for and provide quality training andassessment across all its operations. See Standard 1 of the Standards for RegisteredTraining Organisations.
Assessor Competency Requirements
Each person involved in training, assessment or client service must be competent for thefunctions they perform. See Standard 7 of the Standards for Registered TrainingOrganisations for assessor competency requirements. Standard 7 also specifies thecompetencies that must be held by trainers.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 73 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Assessment Requirements
The RTOs assessments must meet the requirements of the endorsed components of TrainingPackages within its scope of registration. See Standard 8 of the Standards for RegisteredTraining Organisations.
Assessment Strategies
Each RTO must identify, negotiate, plan and implement appropriate learning and assessmentstrategies to meet the needs of each of its clients. See Standard 9 of the Standards forRegistered Training Organisations.
Mutual Recognition
Each RTO must recognise the AQF qualifications and Statements of Attainment issued byany other RTO. See Standard 5 of the Standards for Registered Training Organisations.
Access and Equity and Client Services
Each RTO must apply access and equity principles, provide timely and appropriateinformation, advice and support services that assist clients to identify and achieve desiredoutcomes. This may include reasonable adjustment in assessment. See Standard 6 of theStandards for Registered Training Organisations.
Partnership Arrangements
RTOs must have, and comply with, written agreements with each organisation providingtraining and/or assessment on its behalf. See Standard 1.6 of Standards for RegisteredTraining Organisations.
Recording Assessment Outcomes
Each RTO must have effective administration and records management procedures in place,and must record AQF qualifications and Statements of Attainment issued. See Standards 4and 10.2 of the Standards for Registered Training.
Issuing AQF Qualifications and Statement of Attainment
Each RTO must issue AQF qualifications and Statements of Attainment that meet therequirements of the AQF Implementation Handbook and the endorsed Training Packageswithin the scope of its registration. An AQF qualification is issued once the full requirementsfor a qualification, as specified in the nationally endorsed Training Package are met. AStatement of Attainment is issued where the individual is assessed as competent againstfewer units of competency than required for an AQF qualification. See Standard 10 andSection 2 of the Standards for Registered Training Organisations.
Licensing/Registration Requirements
This section provides information on licensing/registration requirements for this TrainingPackage, with the following important disclaimer.
The developers of this Training Package, and ANTA, consider that no licensing or registrationrequirements apply to RTOs, assessors or candidates with respect to this Training Package.Contact the relevant State or Territory Department(s) to check if there are any licensing orregistration requirements with which you must comply. For further information on this topiccontact Manufacturing Skills Australia on (02) 9955 5500 or www.mskills.com.au .
Pathways
The competencies in this Training Package may be attained in a number of ways includingthrough:
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 74 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
• formal or informal education and training• experiences in the workplace• general life experience, and/or• any combination of the above.
Assessment under this Training Package leading to an AQF qualification or Statement ofAttainment may follow a learning and assessment pathway, an assessment-only orrecognition pathway, or a combination of the two as illustrated in the following diagram.
Each of these assessment pathways leads to full recognition of competencies held - thecritical issue is that the candidate is competent, not how the competency was acquired.
Assessment, by any pathway, must comply with the assessment requirements set out in theStandards for Registered Training Organisations.
Learning and Assessment Pathways
Usually, learning and assessment are integrated, with assessment evidence being collectedand feedback provided to the candidate at anytime throughout the learning and assessmentprocess.
Learning and assessment pathways may include structured programs in a variety of contextsusing a range of strategies to meet different learner needs. Structured learning andassessment programs could be: group-based, work-based, project-based, self-paced, actionlearning-based; conducted by distance or e-learning; and/or involve practice and experiencein the workplace.
Learning and assessment pathways to suit New Apprenticeships have a mix of formalstructured training and structured workplace experience with formative assessment activitiesthrough which candidates can acquire and demonstrate skills and knowledge from therelevant units of competency.
Assessment-Only or Recognition of Prior Learning Pathway
Competencies already held by individuals can be formally assessed against the units ofcompetency in this Training Package, and should be recognised regardless of how, when orwhere they were achieved.
In an assessment-only or Recognition of Prior Learning (RPL) pathway, the candidateprovides current, quality evidence of their competency against the relevant unit ofcompetency. This process may be directed by the candidate and verified by the assessor,such as in the compilation of portfolios; or directed by the assessor, such as throughobservation of workplace performance and skills application, and oral and/or writtenassessment. Where the outcomes of this process indicate that the candidate is competent,
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 75 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
structured training is not required. The RPL requirements of Standard 8.2 of the Standards forRegistered Training Organisations must be met.
As with all assessment, the assessor must be confident that the evidence indicates that thecandidate is currently competent against the endorsed unit of competency. This evidencemay take a variety of forms and might include certification, references from past employers,testimonials from clients, and work samples. The onus is on candidates to provide sufficientevidence to satisfy assessors that they currently hold the relevant competencies. In judgingevidence, the assessor must ensure that the evidence of prior learning is:
• authentic (the candidates own work)• valid (directly related to the current version of the relevant endorsed unit of competency)• reliable (shows that the candidate consistently meets the endorsed unit of competency)• current (reflects the candidates current capacity to perform the aspect of the work
covered by the endorsed unit of competency), and• sufficient (covers the full range of elements in the relevant unit of competency and
addresses the four dimensions of competency, namely task skills, task managementskills, contingency management skills, and job/role environment skills).
The assessment only or recognition of prior learning pathway is likely to be most appropriatein the following scenarios:
• candidates enrolling in qualifications who want recognition for prior learning or currentcompetencies
• existing workers• individuals with overseas qualifications• recent migrants with established work histories• people returning to the workplace, and• people with disabilities or injuries requiring a change in career.
Combination of Pathways
Where candidates for assessment have gained competencies through work and lifeexperience and gaps in their competence are identified, or where they require training in newareas, a combination of pathways may be appropriate.
In such situations, the candidate may undertake an initial assessment to determine theircurrent competency. Once current competency is identified, a structured learning andassessment program ensures that the candidate acquires the required additionalcompetencies identified as gaps.
Assessor Requirements
This section identifies the mandatory competencies for assessors, and clarifies how othersmay contribute to the assessment process where one person alone does not hold all therequired competencies.
Assessor Competencies
The Standards for Registered Training Organisations specify mandatory competencyrequirements for assessors. For information, Standard 7.3 from the Standards for RegisteredTraining Organisations follows:
7.3 a The RTO must ensure that assessments are conducted by a person who has:
• the following competencies* from the Training Package for Assessment andWorkplace Training, or demonstrated equivalent competencies:• TAAASS401A Plan and organise assessment;• TAAASS402A Assess competence;
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 76 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
• TAAASS404A Participate in assessment validation;• relevant vocational competencies, at least to the level being assessed.
b However, if a person does not have all of the competencies in Standards 7.3 a (i)and the vocational competencies as defined in 7.3 a (ii), one person with thecompetencies listed in Standard 7.3 a (i), and one or more persons who have thecompetencies listed in Standard 7.3 a (ii) may work together to conductassessments.
* A person who holds the competencies BSZ401A Plan assessment, BSZ402AConduct assessment, and BSZ403A Review assessment from the TrainingPackage for Assessment and Workplace Training will be accepted for the purposesof this standard. A person who has demonstrated equivalent competencies toBSZ401A and BSZ402A and BSZ403A in the period up to 12 months followingpublication of the Training and Assessment Training Package will also be acceptedfor the purposes of this standard.
MCM04 has adopted the ANTA model assessment guidelines as required. These modelguidelines have been customised by the addition of Section 5 - Assessment for competitivemanufacturing.
Designing Assessment Tools
This section provides an overview on the use and development of assessment tools.
Use of Assessment Tools
Assessment tools provide a means of collecting the evidence that assessors use in makingjudgements about whether candidates have achieved competency.
There is no set format or process for the design, production or development of assessmenttools. Assessors may use prepared assessment tools, such as those specifically developed tosupport this Training Package, or they may develop their own.
Using Prepared Assessment Tools
If using prepared assessment tools, assessors should ensure these are benchmarked, ormapped, against the current version of the relevant unit of competency. This can be done bychecking that the materials are listed on the National Training Information Service(http://www.ntis.gov.au). Materials on the list have been noted by the National Training QualityCouncil as meeting their quality criteria for Training Package support materials.
Developing Assessment Tools
When developing assessment tools, assessors must ensure that they:
• are benchmarked against the relevant unit or units of competency• are reviewed as part of the validation of assessment strategies as required under 9.2 (i)
of the Standards for Registered Training Organisations• meet the assessment requirements expressed in the Standards for Registered Training
Organisations, particularly Standards 8 and 9.
A key reference for assessors developing assessment tools is TAA04 Training andAssessment Training Package and the unit of competency TAAASS403A Developassessment tools. There is no set format or process for the design, production ordevelopment of assessment materials.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 77 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Conducting Assessment
This section details the mandatory assessment requirements and provides information onequity in assessment including reasonable adjustment.
Mandatory Assessment Requirements
Assessments must meet the criteria set out in Standard 8 from the Standards for RegisteredTraining Organisations. For information, Standard 8 from the Standards for RegisteredTraining Organisations is reproduced below.
8 RTO Assessments
The RTOs assessments meet the requirements of the endorsed components ofTraining Packages and the outcomes specified in accredited courses within thescope of its registration.
8.1 The RTO must ensure that assessments (including RPL):
i. comply with the assessment guidelines included in the applicable nationallyendorsed Training Packages or the assessment requirements specified inaccredited courses;
ii. lead to the issuing of a statement of attainment or qualification under the AQF whena person is assessed as competent against nationally endorsed unit(s) ofcompetency in the applicable Training Package or modules specified in theapplicable accredited course;
iii. are valid, reliable, fair and flexible;
iv. provide for applicants to be informed of the context and purpose of the assessmentand the assessment process;
v. where relevant, focus on the application of knowledge and skill to standard ofperformance required in the workplace and cover all aspects workplaceperformance, including task skills, task management skills, contingencymanagement skills and job role environment skills;
vi. involve the evaluation of sufficient evidence to enable judgements to be madeabout whether competency has been attained;
vii. provide for feedback to the applicant about the outcomes of the assessmentprocess and guidance on future options in relation to those outcomes;
viii. are equitable for all persons, taking account of individual needs relevant to theassessment; and
ix. provide for reassessment on appeal.
8.2 a The RTO must ensure that RPL is offered to all applicants on enrolment
b The RTO must have an RPL process that:
i. is structured to minimise the time and cost to applicants; and
ii. provides adequate information, support and opportunities for participants toengage in the RPL process.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 78 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Access and Equity
An individuals access to the assessment process should not be adversely affected byrestrictions placed on the location or context of assessment beyond the requirementsspecified in this Training Package.
Reasonable adjustments can be made to ensure equity in assessment for people withdisabilities. Adjustments include any changes to the assessment process or context that meetthe individual needs of the person with a disability, but do not change competency outcomes.Such adjustments are considered reasonable if they do not impose an unjustifiable hardshipon a training provider or employer. When assessing people with disabilities, assessors areencouraged to apply good practice assessment methods with sensitivity and flexibility.
Assessment for Competitive Manufacturing
General Issues
Assessment of competency will be in accordance with the relevant legislation applying in eachState and Territory. The assessor has a legal duty under both legislation and common lawduty of care to ensure that the assessment activities do not pose a risk to either the candidateor others (such as other workers or the community) who may be in the learning andassessment environment or affected by the learning or assessment activities.
Wherever possible integrated assessment, which reflects the grouping of competencies asthey would be demonstrated in an actual work role, is the preferred means of assessment.The context of the assessment is defined in each unit of competency.
Assessment Considerations for 'Systems' and ' Change/interpersonal' Units
These units reflect the need to consider the system as a whole in competitive manufacturingand also that change is a regular part of life in competitive manufacturing. It may be difficult toassess these units independently and a better approach may be to integrate their assessmentwith that of one or more 'tools' units.
Project-based Assessment
Many of the units of competency (particularly those at Diploma and Advanced Diploma level)lend themselves to a project-based assessment as many of these competencies would beundertaken as part of a project in the workplace. Using these projects for assessment, oralternatively requiring the assessee to undertake a project specifically for assessment fits wellwith the competency. Where project-based assessment is undertaken, then care needs to betaken to not contaminate the evidence of competence with other factors which may occur butwhich are not directly related to the competency. It is also important for any external RTO tobe aware of, and observe, any confidentiality issues which may arise during the project. Thetiming of project-based assessment needs to fit with the requirements of the organisationwhere the project is being conducted and this may not fit conveniently with any externaltimetable.
Integrated Assessment
It is the intention that the ability to perform the unit of competency as a whole be the keycriterion in any assessment process.
Further, it is frequently appropriate to assess more than one unit of competency at the sametime, either because the competencies combine to make a whole job component or becausecertain competencies are only practised in combination with other competencies in aparticular workplace. The assessment of more than one unit of competency concurrently isdesirable, provided adequate evidence is gathered for each competency involved.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 79 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Simulation
Where it is not possible to gather sufficient assessment evidence from a workplace thenassessment may occur off the job in some circumstances. 'Off the job' means that thecandidate is not in productive work at the time the evidence is gathered. In these instances anappropriate simulation must be used where the range of conditions and experiences reflectsrealistic workplace situations.
The true test of competency should always relate to whether the individual can perform to thestandards expected in the workplace, as expressed in the units of competency.
Further Sources of Information
The section provides a listing of useful contacts and resources to assist assessors inplanning, designing, conducting and reviewing of assessments against this Training Package.
Contacts
Manufacturing Skills Australia PO Box 289 NORTH SYDNEY NSW 2059
Ph 02 9955 5500 Fax 02 9955 8044 Web: www.mskills.com.au Email: [email protected]
Australian Training Products Ltd
Level 25, 150 Lonsdale Street
MELBOURNE VIC 3000
PO Box 12211
A'Beckett Street Post Office
MELBOURNE VIC 8006
Telephone: (03) 9655 0600
Fax: (03) 9639 4684
Web: www.atpl.net.au
Email: [email protected]
Innovation and Business Industry Skills Council
Building B, Level 2
192 Burwood Road
Telephone: (03) 9815 7000
Fax: (03) 9815 7001
Email: [email protected]
General Resources
Refer to http://antapubs.dest.gov.au/publications/search.asp to locate the following ANTApublications.
AQF Implementation Handbook, third Edition. Australian Qualifications Framework AdvisoryBoard, 2002, aqf.edu.au
Australian Quality Training Framework (AQTF) - for general information go to:www.dest.gov.au/sectors
Australian Quality Training Framework (AQTF) - for resources and information go to:
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 80 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
www.dest.gov.au
Australian Quality Training Framework Standards for Registered Training Organisations,Australian National Training Authority, Melbourne, 2005. Available in hard copy from Stateand Territory Training Authorities or can be downloaded from www.dest.gov.au
TAA04 Training and Assessment Training Package. This is available from the Innovation andBusiness Skills Australia (IBSA) Industry Skills Council and can be viewed, and componentsdownloaded, from the National Training Information Service (NTIS). National TrainingInformation Service, an electronic database providing comprehensive information aboutRTOs, Training Packages and accredited courses - www.ntis.gov.auStyle Guide for TrainingPackage Support Materials, Australian National Training Authority, Melbourne, 2003. Can bedownloaded from the ANTA page at www.dest.gov.au
Assessment Resources
Training Package Assessment Guides - a range of resources to assist RTOs in developingTraining Package assessment materials developed by DEST with funding from theDepartment of Education, Training and Youth Affairs. It is made up of 10 separate titles, asdescribed at the ANTA publications page of www.dest.gov.au. Go towww.resourcegenerator.gov.au/loadpage.asp?TPAG.htm
Printed and/or CD ROM versions of the Guides can be purchased from Australian TrainingProducts (ATP). The resource includes the following guides:
• Training Package Assessment Materials Kit• Assessing Competencies in Higher Qualifications• Recognition Resource• Kit to Support Assessor Training• Candidates Kit: Guide to Assessment in New Apprenticeships• Assessment Approaches for Small Workplaces• Assessment Using Partnership Arrangements• Strategies for ensuring Consistency in Assessment• Networking for Assessors• Quality Assurance Guide for Assessment
An additional guide "Delivery and Assessment Strategies" has been developed tocomplement these resources.
Assessment Tool Design and Conducting Assessment
VETASSESS AND; Western Australian Department of Training and Employment 2000,Designing Tests - Guidelines for designing knowledge based tests for Training Packages.Vocational Education and Assessment Centre 1997, Designing Workplace Assessment Tools,A self-directed learning program, NSW TAFE.
Manufacturing Learning Australia 2000, Assessment Solutions, Australian Training Products,Melbourne.
Rumsey, David 1994, Assessment practical guide, Australian Government Publishing Service,Canberra.
Assessor Training
Australian Committee on Training Curriculum (ACTRAC) 1994, Assessor training program -learning materials, Australian Training Products, Melbourne.
Australian National Training Authority, A Guide for Professional Development, ANTA,
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 81 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Brisbane.
Australian Training Products Ltd Assessment and Workplace Training, Training Package -Toolbox, ATPL Melbourne.
Green, M, et al. 1997, Key competencies professional development Package, Department forEducation and Childrens Services, South Australia.
Victorian TAFE Association 2000, The professional development CD: A learning tool, VTA,Melbourne.
Assessment System Design and Management
Office of Training and Further Education 1998, Demonstrating best practice in VET project -assessment systems and processes, OTFE Victoria.
Toop, L., Gibb, J. and; Worsnop, P. Assessment system designs, Australian GovernmentPublishing Service, Canberra.
Western Australia Department of Training and VETASSESS 1998, Kit for Skills RecognitionOrganisations, WADOT, Perth.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Assessment Guidelines
Volume 1 of 2 Page 82 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Competency Standards
What is competency?
The broad concept of industry competency concerns the ability to perform particular tasks andduties to the standard of performance expected in the workplace. Competency requires theapplication of specified skills, knowledge and attitudes relevant to effective participation in anindustry, industry sector or enterprise.
Competency covers all aspects of workplace performance and involves performing individualtasks; managing a range of different tasks; responding to contingencies or breakdowns; and,dealing with the responsibilities of the workplace, including working with others. Workplacecompetency requires the ability to apply relevant skills, knowledge and attitudes consistentlyover time and in the required workplace situations and environments. In line with this conceptof competency Training Packages focus on what is expected of a competent individual in theworkplace as an outcome of learning, rather than focussing on the learning process itself.
Competency standards in Training Packages are determined by industry to meet identifiedindustry skill needs. Competency standards are made up of a number of units of competencyeach of which describes a key function or role in a particular job function or occupation. Eachunit of competency within a Training Package is linked to one or more AQF qualifications.
Contextualisation of Units of Competency by RTOs
Registered Training Organisation (RTOs) may contextualise units of competency to reflectlocal outcomes required. Contextualisation could involve additions or amendments to the unitof competency to suit particular delivery methods, learner profiles, specific enterpriseequipment requirements, or to otherwise meet local needs. However, the integrity of theoverall intended outcome of the unit of competency must be maintained.
Any contextualisation of units of competency in this endorsed Training Package must bewithin the bounds of the following advice. In contextualising units of competency, RTOs:
• must not remove or add to the number and content of elements and performance criteria• may add specific industry terminology to performance criteria where this does not distort
or narrow the competency outcomes• may make amendments and additions to the range statement as long as such changes
do not diminish the breadth of application of the competency and reduce its portability,and/or
• may add detail to the evidence guide in areas such as the critical aspects of evidence orresources and infrastructure required where these expand the breadth of thecompetency but do not limit its use.
Components of Units of Competency
The components of units of competency are summarised below, in the order in which theyappear in each unit of competency.
Unit Title
The unit title is a succinct statement of the outcome of the unit of competency. Each unit ofcompetency title is unique, both within and across Training Packages.
Unit Descriptor
The unit descriptor broadly communicates the content of the unit of competency and the skillarea it addresses. Where units of competency have been contextualised from units of
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 83 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
competency from other endorsed Training Packages, summary information is provided. Theremay also be a brief second paragraph that describes its relationship with other units ofcompetency, and any licensing requirements.
Prerequisite Units (optional)
If there are any units of competency that must be completed before the unit, these will belisted.
Application of the Unit
This sub-section fleshes out the unit of competencys scope, purpose and operation indifferent contexts, for example, by showing how it applies in the workplace.
Competency Field (Optional)
The competency field either reflects the way the units of competency are categorised in theTraining Package or denotes the industry sector, specialisation or function. It is an optionalcomponent of the unit of competency.
Sector (optional)
The industry sector is a further categorisation of the competency field and identifies the nextclassification, for example an elective or supervision field.
Elements of Competency
The elements of competency are the basic building blocks of the unit of competency. Theydescribe in terms of outcomes the significant functions and tasks that make up thecompetency.
Performance Criteria
The performance criteria specify the required performance in relevant tasks, roles, skills andin the applied knowledge that enables competent performance. They are usually written inpassive voice. Critical terms or phrases may be written in bold italics and then defined inrange statement, in the order of their appearance in the performance criteria.
Required Skills and Knowledge
The essential skills and knowledge are either identified separately or combined. Knowledgeidentifies what a person needs to know to perform the work in an informed and effectivemanner. Skills describe the application of knowledge to situations where understanding isconverted into a workplace outcome.
Key Competencies
The way the Key Competencies relate to the unit will be described (unless the developer hasdescribed them at the level of the qualification). The Key Competencies are described in moredetail at the end of this section.
Range Statement
The range statement provides a context for the unit of competency, describing essentialoperating conditions that may be present with training and assessment, depending on thework situation, needs of the candidate, accessibility of the item, and local industry andregional contexts. As applicable, the meanings of key terms used in the performance criteriawill also be explained in the range statement.
Evidence Guide
The evidence guide is critical in assessment as it provides information to the RegisteredTraining Organisation (RTO) and assessor about how the described competency may bedemonstrated. The evidence guide does this by providing a range of evidence for the
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 84 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
assessor to make determinations, and by providing the assessment context. The evidenceguide describes:
• conditions under which competency must be assessed including variables such as theassessment environment or necessary equipment
• relationships with the assessment of any other units of competency• suitable methodologies for conducting assessment including the potential for workplace
simulation• resource implications, for example access to particular equipment, infrastructure or
situations• how consistency in performance can be assessed over time, various contexts and with a
range of evidence, and• the required underpinning knowledge and skills
Key Competencies
All Training Packages require the integration of Key Competencies either in each unit ofcompetency, or across a qualification, depending on industry needs and preferences.
The Key Competencies were first defined in 1992 in the project report, Putting GeneralEducation to Work: The Key Competencies Report (Mayer Committee 1992). The skills andknowledge they describe are essential for effective workplace participation and involve thesorts of capabilities commonly used by employers as selection criteria. They underpin theability of employees to adapt to technological, organisational, societal and functional change.
The Key Competencies are generic, in that they apply to work in general, rather than toparticular occupations or industries. They focus on the application of knowledge and skills inan integrated way in workplace situations. The seven Key Competencies are:
1 Communicating ideas and information
The capacity to communicate effectively with others using the range of spoken, written,graphic and other non-verbal means of expression.
2 Collecting, analysing and organising information
The capacity to locate, sift and sort information in order to select what is required and topresent it in a useful way, and evaluate both the information itself and the sources andmethods used to collect it.
3 Planning and organising activities
The capacity to plan and organise ones own work activities, including making good use oftime and resources, sorting out priorities and monitoring ones performance.
4 Working with others in teams
The capacity to interact effectively with other people both on a one-to-one basis and ingroups, including understanding and responding to the needs of a client and workingeffectively as a member of a team to achieve a shared goal.
5 Using mathematical ideas and techniques
The capacity to use mathematical ideas, such as number and space, and techniques such asestimation and approximation, for practical purposes.
6 Solving problems
The capacity to apply problem-solving strategies in purposeful ways, both in situations wherethe problem and the solution are clearly evident and in situations requiring creative thinkingand a creative approach to achieve a desired outcome.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 85 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
7 Using technology
The capacity to apply technology, combining the physical and sensory skills needed tooperate equipment with the understanding of scientific and technological principles needed toexplore and adapt systems.
Performance Levels
There are three levels of performance defined within the Key Competencies. These arestand-alone levels and do not correspond to the AQF qualification levels.
• Performance Level 1 is concerned with the level of competence needed to undertakeactivities efficiently with sufficient self-management to meet the explicit requirements ofthe activity, and to make judgements about the quality of outcomes against establishedcriteria.
• Performance Level 2 describes the competence needed to manage activities requiringthe selection, application and integration of a number of elements, and to select fromestablished criteria to judge quality of process and outcome.
• Performance Level 3 describes the competence needed to evaluate and reshapeprocesses, to establish and use principles in order to determine appropriate ways ofapproaching activities, and to establish criteria for judging quality of process andoutcome.
However, relating performance to the specific industry or workplace context may be moreuseful than interpreting the somewhat abstracted performance levels provided above. Wherethe Key Competencies are defined in the unit of competency, you will find them in a table,together with examples of their application, to help with assessment of their performance.
Also, in evaluating the level of performance for the Key Competencies, consider theperformance expectations at the AQF qualification level involved.
Delivery and Assessment of Key Competencies
The Key Competencies are integral to workplace competency, and, as such must be explicitlyconsidered in the design, customisation, delivery and assessment of vocational education andtraining programs as represented diagrammatically below.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 86 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
Units of Competency
Units of competency have been categorised as:
• systems - coded MCMS###A• change/interpersonal - coded MCMC###A or• tools - coded MCMT###A.
Units must be chosen from each category for qualification purposes. There are most units inthe 'tools' category and this is to cater for the wide variety of approaches chosen bycompetitive manufacturing organisations.
There are no specified 'core' units.
Imported Units
Where sector specific competencies are required, these should be imported from the relevantsector specific Training Package. Relevant units at the same level or at an AQF level one upor one below the selected CMI qualification should be chosen.
Using the CMI units
The development of CMI units and qualifications will occur in number of stages. The units andqualifications in the MCM04 Training Package represent the first development stage and havebeen written to meet the needs of workers who need manufacturing practice skills in additionto specific technical skills.
The CMI units have been written with the intention that they be used in a number of contexts.
The units have been packaged into specific Competitive Manufacturing qualifications. Theseare appropriate for individuals and enterprises where the need for generic manufacturingpractice skills is dominant over the need for specific technical skills. The requirements for aCompetitive Manufacturing qualification is detailed in the Qualifications Framework.
The units are also intended to be imported into sector specific Training Packages and
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 87 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
qualifications. This would be appropriate where the need for sector specific and/or technicalskills is dominant, but there is also a need for generic manufacturing practice skills. Therequirements for these sector specific qualifications will be contained in their respectiveTraining Packages and Qualifications Frameworks.
It is expected that many personnel in manufacturing will have some need of themanufacturing practice skills defined by the Competitive Manufacturing units of competency.Their importation into manufacturing Training Packages is encouraged. Imported units shouldshow the original code number and unit title. The unit code may be used as a first indicator orpossibly appropriate AQF level such that 200 series units may be around AQF 2, 400 seriesunits around AQF 4 and 600 series units around AQF 6. The importation of units should allowfor this estimate to vary by one AQF level (either up or down) and final decisions on the levelin which they are to be packaged in the importing Training Package needs to be made withconsideration of the industry and following normal processes for making these decisions.
MCM04 Competitive Manufacturing Training Package (Version 3) Date this PDF was generated: 30 November 2007Competency Standards
Volume 1 of 2 Page 88 of 88© Commonwealth of Australia, 2004 To be reviewed by: 31 July 2006
MCM04 Competitive Manufacturing Training PackageCompetitive Manufacturing Training Package (Background,
Qualification Framework, Assessment Guidelines)Volume 1 of 2
MCM04 Competitive Manufacturing Training PackageCompetitive Manufacturing Training Package (Background, Qualification Framework, Assessment
Guidelines)
Volume 1 of 2