L-1

Acc

esso

ries

L-2

Accessories The bearing products in this catalog may require

accessories to further enhance their value. These

accessories range from end caps to lubrication. These

accessories can be used on several bearing platforms

and are available for customization with support from

our Application Engineering group.

Acc

esso

ries

End Caps and Backside Shields

L-3

Acc

esso

ries

End Caps and Backside SealsAdditional sealing accessories are available for enhanced bearing and personal protection. End caps provide a guard from rotating shafts and conform to OHSA requirements for personal protection. In addition, these accessories together can better protect against high-pressure wash down and help reduce bearing moisture contact. Backside shield gaskets are mounted between the bearing and the equipment frame to reduce moisture runoff. Depending on your preference, these accessories are illustrated on the following pages.

End CapsEnd caps offer better protection against high-pressure wash down and can be used to reduce bearing moisture contact and provide personal protection to conform with OSHA and other regulatory guidelines.

Stainless Bolt On End CapDurable 304 stainless steel for resistance to corrosion and chemical attack, bolts onto housing with four cap screws for excellent holding power, drain hole to be positioned towards the bottom to reduce moisture buildup against the bearing.

Cap Availability

Product Line Polymer Snap On Stainless Bolt On

Sealmaster CR Gold Stainless Y N/A

Sealmaster PN Gold Stainless Y Y*

Sealmaster PN Gold Composite Y Y*

Sealmaster Material Handling Y Y*

*Bolt on caps for mounted ball bearings are for fl ange housing designs only. Caps fi t on housings that have been modifi ed with the appropriate bolt pattern as defi ned by the prefi x “B” in the part number. Example: Sealmaster PN Gold CRBFTS-PN24, Sealmaster Gold BSFT-24*Note: Additional end cap designs exist for non-standard parts or industry specifi c designs. Consult Application Engineering for more information.

Polymer Snap On CapPolypropylene material for resistant to corrosion, hand snap into housing for easy installation, and incorporate a shielded drain hole to reduce moisture buildup against the bearing.

Shielded Drain Hole

End Caps and Backside Shields

L-4

Acc

esso

ries

Backside ShieldBackside shield gaskets are mounted between the bearing and the equipment frame to reduce moisture runoff. Backside shields are available for two and four bolt flange mounted ball bearings.

Backside shields are made of nitrile rubber gaskets to reduce bearing moisture contact mated to a 304 stainless steel plate for improved assembly strength, with drain slots to reduce moisture buildup against the back of the bearing housing.

End Cap Part IdentificationBore Size

Unit Size Polymer Snap On Bolt On (2-bolt, 3-bolt, 4-bolt flange)

inch mm Closed Open Closed Open 3/4 - 12

ECC-12 ECO-12 N/A N/A- 20 204

7/8 - 14ECC-16

ECO-14BEC-16 BEO-16 1 - 16

ECO-16- 25 205

1 1/8 - 18

ECC-19

ECO-19

BEC-19

N/A1 3/16 - 19 ECO-19 BEO-19 1 1/4R - 20R ECO-20R BEO-20R

- 30 206 ECO-19 BEO-19 1 1/4 - 20

ECC-23

ECO-20

BEC-23

BEO-20 1 3/8 - 22 ECO-23 BEO-22

1 7/16 - 23 ECO-23 BEO-23 - 35 207 ECO-23 BEO-22

1 1/2 - 24ECC-24 ECO-24 BEC-24 BEO-24

- 40 2081 11/16 - 27

ECC-27ECO-27

BEC-27BEO-27

1 3/4 - 28 N/A BEO-28- 45 209 N/A BEO-28

1 15/16 - 31ECC-31

ECO-31BEC-31 BEO-312 - 32R N/A

- 50 210 ECO-312 - 32

ECC-35 ECO-35 BEC-35 BEO-32

2 3/16 - 211 BEO-35- 55 35 BEO-35

2 3/8 - 38ECC-39 ECO-39 BEC-39 BEO-392 7/16 - 39

- 60 212

Mounted Ball Bearing Caps

Bore SizeUnit Size 2 Bolt Flange 4 Bolt Flangeinch mm

3/4 - 122BSS-12 4BSS-12

- 20 2041 - 16

2BSS-16 4BSS-16- 25 205

1 3/16 - 19 2BSS-19 4BSS-19- - 20R 2BSS-20R 4BSS-20R- 30 206 2BSS-19 4BSS-19

1 1/4 - 20 2BSS-20 4BSS-201 3/8 - 22 2BSS-22 4BSS-22

- 35 207 2BSS-22 4BSS-221 7/16 - 23 2BSS-23 4BSS-231 1/2 - 24 2BSS-24 4BSS-24

- 40 - 2BSS-208 4BSS-2081 11/16 - 27 2BSS-27 4BSS-27

- 45 - N/A N/A1 15/16 - 31

2BSS-31 4BSS-31- 50 2102 - 32 N/A 4BSS-32

2 3/16 - 35 2BSS-35 4BSS-35- 55 211 2BSS-35 4BSS-35

2 3/8 - 38 2BSS-38 4BSS-382 7/16 - 39 N/A 4BSS-39

- 60 212 2BSS-38 4BSS-38

Notes: 1. Bolt on caps for mounted ball bearings are for flange housing designs only. Caps fit on housings that have been modified with the appropriate bolt pattern as defined by the prefix “B” in the part number. Example: Sealmaster PN Gold CRBFTS-PN24, Sealmaster Gold BSFT-24 2. Ends caps may reduce bearing misalignment capability.

Grease

L-5

Acc

esso

ries

Sealmaster GoldPlex®-HP GreaseFormulated by Sealmaster engineers in conjunction with leading lubrication experts, GoldPlex-HP high performance mounted bearing grease is specifically designed to help maximize the operating performance of Sealmaster brand ball and roller bearings. This superior lubricant is formulated with a highly compatible lithium complex thickener and specially processed base oil. A finely tuned additive package further improves performance by providing high film strength, extreme pressure (EP), and anti-wear properties.

Sealmaster GoldPlex-HP provides effective lubrication over a wide range of temperatures with a low temperature performance of -40°F (-40°C). Test results show that GoldPlex-HP outperforms standard bearing greases in oxidation prevention and load carrying capabilities, which contribute to longer bearing life.

This lubricant's performance advantages include: • Superior corrosion resistance • Wide operating temperature range (-40°F to 350°F) • Significantly lowers bearing running temperature • Increased EP protection • Lengthens lubrication cycles in most applications • Excellent consistency

GoldPlex-HP sets a new standard for extreme pressure protection, long life and dependable performance.

GoldPlex HP 14 oz.

GoldPlex HP 35 lb Pail

GoldPlex HP 120 lb Keg

GoldPlex HP 400 lb Drum

Availability

Product Specifications Thickener Type Lithium Complex

Texture Smooth

Color Gold

60-Stroke Penetration, ASTM D 217, 77F 280-300

Droppino Point, ASTM D 2265, F (C) 500 (260)

Oxidation Stability, ASTM D 942, Psi Drop/100 5

Rust and Corrosion Protection, ASTM D 1743 Pass

Modified with 5% Synthetic Seawater Pass

Water Washout, ASTM D 1264, 175F, % 5

Timken* OK Load, ASTM D 2509 50

4-Ball EP, ASTM D 2596 Weld Pt. kg 250

4-Ball Wear, ASTM D 2266, Scar Dia. Mm, 40 kg 0.60

Oil Separation, ASTM D 1742, Mass % 10

Base Oil Viscosity SUS @ 100F 575-675

Base Oil Viscosity cSt @ 100C 12.2

Base Oil Viscosity cSt @ 40C 115

NLGI # 2

Operating Temperature Range -40°F to 350°F

* The following trade names, trademarks and/or registered trademarks are used in this material by Regal Power Transmission Solutions for comparison purposes only, are NOT owned or controlled by ERegal Power Transmission Solutions and are believed to be owned by the following parties: The Timken Company. Regal Power Transmission Solutions cannot and does not represent or warrant the accuracy of this information.

GoldPlex-HP vs. Synthetic Hydrocarbon Grease**

10

8

6

4

2

0

D 942 - Oxidation Loss

D 5969 - Rust Prevention

D 2596 4-Ball EP IndexD 2596 Weld Load-KG

D 4693 Low Temp Torque

D 942 - Oxidation Loss

D 5969 - Rust Prevention

D 2596 4-Ball EP IndexD 2596 Weld Load-KG

D 4693 Low Temp Torque

GoldPlex-HP vs. Multi-Purpose Lithium Complex Grease**

10

8

6

4

2

0

GoldPlex-HPMulti-Purpose Lithium ComplexSynthetic Hydrocarbon

Grease

L-6

Acc

esso

ries

* The following trade names, trademarks and/or registered trademarks are used in this material by Regal Power Transmission Solutions for comparison purposes only, are NOT owned or controlled by Regal Power Transmission Solutions and are believed to be owned by the following parties: The Timken Company. Regal Power Transmission Solutions cannot and does not represent or warrant the accuracy of this information.

Sealmaster GoldPlex®-FG Food Grade GreaseGoldPlex-FG food grade, mounted bearing grease is suitable for mounted bearing lubrication where incidental contact with food products may occur or any applications where clean, routine lubrication is required.

This lubricant's performance advantages include: • Superior corrosion resistance • Excellent water washout properties • Compatible with major thickeners - Aluminum Complex - Calcium Complex - Polyurea • USDA H1 category approved • Superior dropping point 572°F (300°C) • Nonstaining and nontoxic

All Sealmaster PN Gold and RPB-CR bearings are factory filled with GoldPlex-FG lubricant.

GoldPlex FG 14 oz.

GoldPlex FG 35 lb Pail

GoldPlex FG 120 lb Keg

Availability

Product Specifications Thickener Type Calcium Sulfonate

Texture Smooth

Color White

60-Stroke Penetration, ASTM D 217, 77F 265-295

Dropping Point, ASTM D 2265, F (C) 572 (300)

Oxidation Stability, ASTM D 942, Psi Drop/100 1

Rust and Corrosion Protection, ASTM D 1743 Pass

Modified with 5% Synthetic Seawater Pass

Water Washout, ASTM D 1264, 175F, % 2.75

Timken* OK Load, ASTM D 2509 65

4-Ball EP, ASTM D 2596 Weld Pt. kg 620

4-Ball Wear, ASTM D 2266, Scar Dia. Mm, 40 kg 0.45

Oil Separation, ASTM D 1742, Mass % 0.2

Base Oil Viscosity SUS @ 100F 523

Base Oil Viscosity cSt @ 100C 10.5

Base Oil Viscosity cSt @ 40C 100

NLGI # 2

Operating Temperature Range -40°F to 350°F

GoldPlex-FG: Indicates food grade mounted bearing grease for use in a wide variety of bearing applications in the food and beverage industries.

GoldPlex-FGAl Complex - Synthetic OilAl Complex - Mineral Oil

GoldPlex-FG vs. Al Complex Synthetic **Water Washout

Oil Separation Rust Prevention5% Sea WaterArea Rusted

4 Ball EP Index - RatioWeld Load - Ratio

10

8

6

4

2

0

Water Washout

Rust Prevention5% Sea WaterArea Rusted

4 Ball EP Index - RatioWeld Load - Ratio

Oil Separation

GoldPlex-FG vs. Al Complex Mineral Oil **

10

8

6

4

2

0

Grease

L-7

Acc

esso

ries

Sealmaster GoldPlex-HP Grease continuedProtective Grease Fitting Caps

Cap Color Description Part No.

Note: The top of the grease fitting cap provides space to mark installation date.

Gold Indicates that the bearing is factory filled withSealmaster GoldPlex-HP Grease 759376

White Indicates that the bearing is factory filled withSealmaster GoldPlex-FG Grease

759646

Red Indicates that the bearing is factory filled withHigh Temperature Grease

759647

Black Indicates that the bearing is factory filled with aNon-Standard Grease

759648

Grease Fittings

L-8

Acc

esso

ries

Lubrication FittingsLubrication fittings provide a means quickly connecting a hose or grease gun to a bearing for relubrication. They should be permanently installed onto the bearing and can be threaded or driven into a lubrication or oil hole. It is important to select the correct lubrication fitting for the bearing and application. On Sealmaster ball bearings the lubrication fitting also functions as a stop for the lock pin. Caution should be taken when replacing the fitting on these bearings.

Common Suffix N/A CSK CTJIncludes plastic plug not shown

1/4-28 Male

1641B*

A

1911B*

D

51942*

1/8 NPT Female

I

1/8 NPT Male

1640B*

B

1613B*

E

J

1/8 Hole

3/16

7/16 Hex

29/64

57/64

19/64

45°

1/8 NPT Female

43761*

H

1/4 NPT Male

1/4-28 Plug

G

1627B*

C1/8 NPT Female

45120*

F

*Part Numbers listed below picture drawings are Alemite part numbers. Alemite is a registered trademark of Alemite LLC. This trade name, trademark and/or registered trademark is property of their respective owner and is not owned or controlled by Regal Power Transmission Solutions

Grease Fittings

L-9

Acc

esso

ries

Bore Size in Inches

Brand Bearing Unit Description

1/2 - 1 1/8

1 3/16 - 1 1/4R or S

1 1/4 - 1 5/8

1 11/16 - 1 3/4

1 7/18 - 2 1/8 2 3/16 2 1/4 -

2 7/8 2 15/16 3+

Sealmaster

FB, FBMH A A A - B - - - -MFC A A A B B B B C CMFP - - - - B B B C C

MP, EMP, MPD A A A B B B B C CMSC A A A A A B B B B

MSF, EMSF A A A B B B B C CMSFPD - - - - B B B C CMSFT A A A B B - - - -MSPD - - - B B B B C CMST D D D E E E E E+F E+F

NP , ENP, NPMH A A A A B B B - -NPD A A A A B B B - -NPL A A A A B B B - -SC A A A A A A B B -

SCHB G G G H H H H H FSEHB A A A B B B B B C

SF. ESF, SFMH A A A A B B B B -SFC A A A A B B B B C

SFT, ESFT, SFTMH A A A A B B - - -SP A A A A B B B B C

SPD A A A A B B B B CSPM - A A B B B B - -

ST, STMH D D D D E E E E ETB, TBMH A A A A B - - - -

TFT A A A - - - - - -

Browning

VF2B-200 A A B B B B - - -VF2B-300 A B B B B - - - -

VF2E-100, 200 A A B B B B B B -VF2E-100M A A A - - - - - -

VF2S-100, 200 A A B B B B B B -VF2S-100M A A A - - - - - -VF2S-300 A B B B B - - - -

VF3E-100M A A A - - - - - -VF3S-100M A A A - - - - - -VF4B-200 A A B B B B B - -VF4B-300 A B B B B B - - -

VF4E-100, 200 A A B B B B B B -VF4S-100, 200 A A B B B B B B -

VFBS-200 A A B - B - - - -VFBB-200 A A B - B - - - -VF4S-300 A B B B B B B B BVFCB-200 A A A A A A B - -VFCB-300 A A A A A B - - -VFCS-200 A A A A A A B - -VFCS-300 A A A A A B B B BVPB-200 A A B B B B B - -VPB-300 A B B B B B - - -

VPE-100, 200 A A B B B B B B -VPE-100M A A A - - - - - -VPLB-200 A A B B B B B - -

VPLE-100, 200 A A B B B B B B -VPLS-100, 200 A A B B B B B B -VPS-100, 200 A A B B B B B B -

VPS-100M A A A - - - - - -VPS-300 A B B B B B B B B

VTBE-100 A A B B B - - - -VTBE-200 A A B B B B B - -

VTBS-100, 200 A A B B B - - - -VTWE-100, 200 D D E E E E E - -VTWS-100, 200 D D E E E E E - -

VTWS-300 D E E E E E E E E

Lubrication Fittings continuedLubrication Fitting Chart Mounted Ball Bearings

Grease Fittings

L-10

Acc

esso

ries

Brand Series All Shaft Sizes

BrowningFBE920, PBE920 B

TUE920 E

Sealmaster

DRPB B

RPB B

RPBXT B

RFB B

RFP B

SPB B

USBF J

USFB, USFBE USF3B B

USFC A

USFCE, USRB USRBE B

USTU E

Lubrication Fittings continuedLubrication Fitting Chart Mounted Roller Bearings

CF / CFH Inch Camrol

From Sizes To Sizes Lube Fitting Size Part No.

1/2” 11/16” 1/8” Drive 3019*

3/4” 2 3/4” 3/16” Drive 1728B*

3” 4” 1/4” Drive 1743B*

5” 10” 1/4” NPT 1627B*

Lubrication Fitting Chart Cam Followers

Lubrication Fitting Chart Sealmaster Rod Ends

Bore Size Fitting Number Thread Size Hex size

1/4” - 7/16” #3018 (no ball check) #6-40 UNF-2A 1/4”

1/2” - 1” #3016 (no ball check) #10-32 UNF-2A 1/4”

*Part Numbers listed below picture drawings are Alemite part numbers. Alemite is a registered trademark of Alemite LLC. This trade name, trademark and/or registered trademark is property of their respective owner and is not owned or controlled by Regal Power Transmission Solutions

Oil Hole Plugs

L-11

Acc

esso

ries

Oil hole plugs are used to block lubrication holes when the port is not required for relubrication the bearing. These plugs help retain the grease or oil, and also help prevent contamination from entering the bearing. All McGill Cam Followers are supplied with oil hole plugs for the number of lubrication holes present.

Oil Hole PlugsIN

CH

Description Part ID Pack Qtyinch

TypeBasic

DiameterBasic

Length

CF-1/2 Brass Plug 9712160050 100 pc .131 .095 Solid

CF-3/4 Solid Plug 9712160075 100 pc .194 .125 Solid

CF-3 Steel Plug 9712160300 100 pc .255 .25 to .31 Hollow

Accessories

L-12

Acc

esso

ries

For more information on bearing capabilities outside of our standard offering, please contact Application Engineering (800) 626-2093.