mc13150 technical data sheet - nxp semiconductors · mc13150 motorola analog ic device data 3 ac...
TRANSCRIPT
![Page 1: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/1.jpg)
SEMICONDUCTORTECHNICAL DATA
NARROWBAND FM COILLESSDETECTOR IF SUBSYSTEM
FOR CELLULAR AND ANALOG APPLICATIONS
FTA SUFFIXPLASTIC PACKAGE
CASE 977(LQFP–24)
24 1
Order this document by MC13150/D
FTB SUFFIXPLASTIC PACKAGE
CASE 873(LQFP–32)
32
1
1MOTOROLA ANALOG IC DEVICE DATA
The MC13150 is a narrowband FM IF subsystem targeted at cellular andother analog applications. Excellent high frequency performance isachieved, with low cost, through use of Motorola’s MOSAIC 1.5 RF bipolarprocess. The MC13150 has an onboard Colpitts VCO for Crystal controlledsecond LO in dual conversion receivers. The mixer is a double balancedconfiguration with excellent third order intercept. It is useful to beyond200 MHz. The IF amplifier is split to accommodate two low cost cascadedfilters. RSSI output is derived by summing the output of both IF sections. Thequadrature detector is a unique design eliminating the conventional tunablequadrature coil.
Applications for the MC13150 include cellular, CT–1 900 MHz cordlesstelephone, data links and other radio systems utilizing narrowband FMmodulation.
• Linear Coilless Detector
• Adjustable Demodulator Bandwidth
• 2.5 to 6.0 Vdc Operation
• Low Drain Current: < 2.0 mA
• Typical Sensitivity of 2.0 µV for 12 dB SINAD
• IIP3, Input Third Order Intercept Point of 0 dBm
• RSSI Range of Greater Than 100 dB
• Internal 1.4 kΩ Terminations for 455 kHz Filters
• Split IF for Improved Filtering and Extended RSSI Range
ORDERING INFORMATION
DeviceOperating
Temperature Range Package
MC13150FTATA = –40 ° to +85°C
LQFP–24
MC13150FTBTA = –40 ° to +85°C
LQFP–32
AFTFilt
PIN CONNECTIONS
Mixer
LimiterLimiter
Mixer
IF
IF
RSSIb
DETout
VEE2
DETGain
AFTout
RSSIb
DETout
VEE (N/C)
VEE2
DETGain
VEE (N/C)
AFTFilt
AFTout
MixOut
VCC1
VCC (N/C)
IFin
IFd1
VCC (N/C)
IFd2
IFout
Mixout
VCC1
IFin
IFd1
IFd2
IFout
1
2
3
4
5
6
18
17
16
15
14
13
7 8 9 10 11 12
24 23 22 21 20 19
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
VC
C2
LIM
in
LIM
d1
LIM
d2
BWAd
j
F Adj
Mix
in
V EE1
LOe
LOb
Enab
le
RSS
I
Mix
in
V EE1
LOe
LOb
Enab
le
RSS
I
V CC
(N/C
)
V CC
(N/C
)
VC
C2
LIM
in
LIM
d1
LIM
d2
BWAd
j
F Adj
V CC
(N/C
)
V CC
(N/C
)
Det
ecto
r
Det
ecto
r
9 10 13 14 15 1611 12
32 31 28 27 26 2530 29
LQFP–24 LQFP–32
Motorola, Inc. 1997 Rev 2
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 2: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/2.jpg)
MC13150
2 MOTOROLA ANALOG IC DEVICE DATA
MAXIMUM RATINGS
Rating Pin Symbol Value Unit
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Power Supply Voltage ÁÁÁÁÁÁ
2, 9ÁÁÁÁÁÁÁÁÁÁ
VCC(max)ÁÁÁÁÁÁÁÁÁÁ
6.5 ÁÁÁÁÁÁÁÁ
Vdc
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Junction Temperature ÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁÁ
TJmaxÁÁÁÁÁÁÁÁÁÁ
+150 ÁÁÁÁÁÁÁÁ
°CÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Storage Temperature Range ÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁÁ
TstgÁÁÁÁÁÁÁÁÁÁ
–65 to +150ÁÁÁÁÁÁÁÁ
°C
NOTE: 1. Devices should not be operated at or outside these values. The ”Recommended OperatingLimits” provide for actual device operation.
2. ESD data available upon request.
RECOMMENDED OPERATING CONDITIONS
Rating Pin Symbol Value UnitÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Power Supply Voltage TA = 25°C–40°C ≤ TA ≤ 85°C
(See Figure 22)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
2, 921, 31
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
VCCVEE
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
2.5 to 6.00
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Vdc
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Input FrequencyÁÁÁÁÁÁÁÁÁÁÁÁ
32ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
fin
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
10 to 500ÁÁÁÁÁÁÁÁÁÁÁÁ
MHzÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Ambient Temperature RangeÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
TA
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
–40 to +85ÁÁÁÁÁÁÁÁÁÁÁÁ
°CÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Input Signal LevelÁÁÁÁÁÁÁÁÁÁÁÁ
32ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Vin
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
0ÁÁÁÁÁÁÁÁÁÁÁÁ
dBm
DC ELECTRICAL CHARACTERISTICS (TA = 25°C, VCC1 = VCC2 = 3.0 Vdc, No Input Signal.)
Characteristics Condition Pin Symbol Min Typ Max Unit
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Total Drain Current(See Figure 2)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
VS = 3.0 VdcÁÁÁÁÁÁÁÁÁÁÁÁ
2 + 9ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ITOTAL ÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁÁÁ
1.7 ÁÁÁÁÁÁÁÁÁÁÁÁ
3.0 ÁÁÁÁÁÁÁÁÁÁÁÁ
mA
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Supply Current, Power Down(See Figure 3)
ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁ
2 + 9ÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁ
40 ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁ
nA
AC ELECTRICAL CHARACTERISTICS (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO = 50.455 MHz,LO Level = –10 dBm, see Figure 1 Test Circuit*, unless otherwise specified.)
Characteristics Condition Pin Symbol Min Typ Max UnitÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
12 dB SINAD Sensitivity(See Figure 15)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
fmod = 1.0 kHz;fdev = ±5.0 kHz
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
32ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁ
–100ÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁ
dBm
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
RSSI Dynamic Range(See Figure 7)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
25 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁ
100ÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁ
dB
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Input 1.0 dB Compression PointInput 3rd Order Intercept Point(See Figure 18)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
––
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
––ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1.0 dB C. Pt.IIP3
ÁÁÁÁÁÁÁÁÁ
––ÁÁÁÁÁÁÁÁÁ
–11–1.0ÁÁÁÁÁÁÁÁÁÁÁÁ
––ÁÁÁÁÁÁÁÁÁ
dBm
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Coilless Detector BandwidthAdjust (See Figure 11)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Measured with No IF FiltersÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
∆BW adj ÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁ
26ÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁ
kHz/µA
MIXER
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Conversion Voltage Gain(See Figure 5)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Pin = –30 dBm;PLO = –10 dBm
ÁÁÁÁÁÁÁÁÁÁ
32 ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
10ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
dB
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Mixer Input ImpedanceÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Single–EndedÁÁÁÁÁÁÁÁÁÁ
32ÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
200ÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
ΩÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Mixer Output ImpedanceÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁÁ
1ÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
1.5ÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁ
kΩ
LOCAL OSCILLATORÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
LO Emitter Current(See Figure 26)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
29ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
–ÁÁÁÁÁÁÁÁÁ
30ÁÁÁÁÁÁÁÁÁ
63ÁÁÁÁÁÁÁÁÁÁÁÁ
100ÁÁÁÁÁÁÁÁÁ
µA
IF & LIMITING AMPLIFIERS SECTION
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
IF and Limiter RSSI Slope ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Figure 7 ÁÁÁÁÁÁÁÁÁÁ
25 ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
0.4ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
µA/dB
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
IF Gain ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Figure 8 ÁÁÁÁÁÁÁÁÁÁ
4, 8 ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
42ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
dB
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
IF Input & Output Impedance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁ
4, 8 ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
1.5ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
kΩ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Limiter Input Impedance ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁ
10 ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
1.5ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
kΩ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Limiter Gain ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
96ÁÁÁÁÁÁÁÁ
– ÁÁÁÁÁÁ
dB
* Figure 1 Test Circuit uses positive (VCC) Ground.
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 3: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/3.jpg)
MC13150
3MOTOROLA ANALOG IC DEVICE DATA
AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO = 50.455 MHz,LO Level = –10 dBm, see Figure 1 Test Circuit*, unless otherwise specified.)
Characteristics UnitMaxTypMinSymbolPinCondition
DETECTOR
Frequency Adjust Current Figure 9,fIF = 455 kHz
16 – 41 49 56 µA
Frequency Adjust Voltage Figure 10,fIF = 455 kHz
16 – 600 650 700 mVdc
Bandwidth Adjust Voltage Figure 12,I15 = 1.0 µA
15 – – 570 – mVdc
Detector DC Output Voltage(See Figure 25)
– 23 – – 1.36 – Vdc
Recovered Audio Voltage fdev = ±3.0 kHz 23 – 85 122 175 mVrms
* Figure 1 Test Circuit uses positive (VCC) Ground.
Figure 1. Test Circuit
MixerIn
1:4Z Xformer
10 µ 220 n
VEE1LO Input
100 n
49.9
Enable
RSSI
RSSIBuffer
DetectorOutput
RL100 k
RS100 k
VEE2
100 p
220 n 10 µ
100 k V18–V17 = 0;fIF = 455 kHz
I16I15220 n
49.9
LimiterIn
IF AmpOut
1.5 k
220 n
49.9
IFIn
MixerOut
1.5 k
32
VEE1
Mixer
VCC1 LocalOscillator RSSI
Buffer
IF
VCC2
VEE2
Limiter
(6)
Det
ecto
r
+
+
220 n
220 n
220 n
220 n
220 n
220 n
31 30 29 28 27 26 25
9 10 11 12 13 14 15 16
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
220 n220 n
100 n
This device contains 292 active transistors.
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 4: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/4.jpg)
MC13150
4 MOTOROLA ANALOG IC DEVICE DATA
MC13150 CIRCUIT DESCRIPTION
GeneralThe MC13150 is a very low power single conversion
narrowband FM receiver incorporating a split IF. This deviceis designated for use as the backend in analog narrowbandFM systems such as cellular, 900 MHz cordless phones andnarrowband data links with data rates up to 9.6 k baud. Itcontains a mixer, oscillator, extended range received signalstrength indicator (RSSI), RSSI buffer, IF amplifier, limiting IF,a unique coilless quadrature detector and a device enablefunction (see Package Pin Outs/Block Diagram).
Low Current OperationThe MC13150 is designed for battery and portable
applications. Supply current is typically 1.7 mAdc at 3.0 Vdc.Figure 2 shows the supply current versus supply voltage.
EnableThe enable function is provided for battery powered
operation. The enabled pin is pulled down to enable theregulators. Figure 3 shows the supply current versus enablevoltage, Venable (relative to VCC) needed to enable thedevice. Note that the device is fully enabled at VCC – 1.3 Vdc.Figure 4 shows the relationship of enable current, Ienable toenable voltage, Venable.
MixerThe mixer is a double–balanced four quadrant multiplier
and is designed to work up to 500 MHz. It has a single endedinput. Figure 5 shows the mixer gain and saturated outputresponse as a function of input signal drive and for –10 dBmLO drive level. This is measured in the application circuitshown in Figure 15 in which a single LC matching network isused. Since the single–ended input impedance of the mixer is200 Ω, an alternate solution uses a 1:4 impedancetransformer to match the mixer to 50 Ω input impedance. Thelinear voltage gain of the mixer alone is approximately 4.0 dB(plus an additional 6.0 dB for the transformer). Figure 6shows the mixer gain versus the LO input level for variousmixer input levels at 50 MHz RF input.
The buffered output of the mixer is internally loaded,resulting in an output impedance of 1.5 kΩ.
Local OscillatorThe on–chip transistor operates with crystal and LC
resonant elements up to 220 MHz. Series resonant, overtonecrystals are used to achieve excellent local oscillator stability.3rd overtone crystals are used through about 65 to 70 MHz.Operation from 70 MHz up to 200 MHz is feasible using theon–chip transistor with a 5th or 7th overtone crystal. Toenhance operation using an overtone crystal, the internaltransistor’s bias is increased by adding an external resistorfrom Pin 29 (in 32 pin QFP package) to VEE to keep theoscillator on continuously or it may be taken to the enable pinto shut it off when the receiver is disabled. –10 dBm of localoscillator drive is needed to adequately drive the mixer(Figure 6). The oscillator configurations specified above aredescribed in the application section.
RSSIThe received signal strength indicator (RSSI) output is a
current proportional to the log of the received signalamplitude. The RSSI current output is derived by summingthe currents from the IF and limiting amplifier stages. Anexternal resistor at Pin 25 (in 32 pin QFP package) sets thevoltage range or swing of the RSSI output voltage. Linearityof the RSSI is optimized by using external ceramic bandpassfilters which have an insertion loss of 4.0 dB. The RSSI circuitis designed to provide 100+ dB of dynamic range withtemperature compensation (see Figures 7 and 23 whichshow the RSSI response of the applications circuit).
RSSI BufferThe RSSI buffer has limitations in what loads it can drive.
It can pull loads well towards the positive and negativesupplies, but has problems pulling the load away from thesupplies. The load should be biased at half supply toovercome this limitation.
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 5: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/5.jpg)
MC13150
5MOTOROLA ANALOG IC DEVICE DATA
LO DRIVE (dBm)
VENABLE, ENABLE VOLTAGE (Vdc)
Figure 2. Supply Currentversus Supply Voltage
VENABLE, SUPPLY VOLTAGE (Vdc)
Figure 3. Supply Currentversus Enable Voltage
Figure 4. Enable Currentversus Enable Voltage
Figure 5. Mixer IF Output Level versusRF Input Level
Figure 6. Mixer IF Output Level versusLocal Oscillator Input Level
Figure 7. RSSI Output Currentversus Input Signal Level
2.0
1.6
1.2
0.8
0.4
01.5 2.5 3.5 4.5 5.5 6.5 7.5
TA = 25°C
MIX
ER IF
OU
TPU
T LE
VEL
(dBm
)
MIX
ER IF
OU
TPU
T LE
VEL
(dBm
)
VENABLE, ENABLE VOLTAGE (Vdc)
10–2
0.5
10–3
10–4
10–5
10–6
10–7
10–8
10–9
10–100.7 0.9 1.1 1.3 1.5
VCC = 3.0 VdcTA = 25°CVENABLE MeasuredRelative to VCC
70
60
50
40
30
20
10
0
–100 0.4 0.8 1.2 1.6 2.0
RF INPUT LEVEL (dBm)
SIGNAL INPUT LEVEL (dBm)
VCC = 3.0 VdcTA = 25°C
20
10
0
–10
–20
–30
–50–50 –40 –30 –20 –10 0
–40
VEE = –3.0 VdcTA = 25°C
fRF = 50 MHz; fLO = 50.455 MHzLO Input Level = –10 dBm(100 mVrms)(Rin = 50 Ω; Rout = 1.4 kΩ
20
0
–20
–40
–80
–60
–60 –50 –40 –30 –20 –10 0
VEE = –3.0 VdcTA = 25°C
fRF = 50 MHz; fLO = 50.455 MHzRin = 50 Ω; Rout = 1.4 kΩ
RF In = 0 dBm
–20 dBm
–40 dBm
50
40
30
20
0
10
–120 –100 –80 –60 –40 –20 0
VCC = 3.0 Vdcf = 50 MHzfLO = 50.455 MHz455 kHzCeramic FilterSee Figure 15
I SU
PPLY
, SU
PPLY
CU
RR
ENT
(mA)
I SU
PPLY
, SU
PPLY
CU
RR
ENT
(A)
IA
)µ
ENAB
LE, E
NAB
LE C
UR
REN
T (
RSS
I OU
TPU
T C
UR
REN
T (
A)µ
10 20
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 6: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/6.jpg)
MC13150
6 MOTOROLA ANALOG IC DEVICE DATA
IF AmplifierThe first IF amplifier section is composed of three
differential stages. This section has internal dc feedback andexternal input decoupling for improved symmetry andstability. The total gain of the IF amplifier block isapproximately 42 dB at 455 kHz. Figure 8 shows the gain ofthe IF amplifier as a function of the IF frequency.
The fixed internal input impedance is 1.5 kΩ; it is designedfor applications where a 455 kHz ceramic filter is used and noexternal output matching is necessary since the filter requiresa 1.5 kΩ source and load impedance.
Overall RSSI linearity is dependent on having totalmidband attenuation of 10 dB (4.0 dB insertion loss plus 6.0dB impedance matching loss) for the filter. The output of theIF amplifier is buffered and the impedance is 1.5 kΩ.
LimiterThe limiter section is similar to the IF amplifier section
except that six stages are used. The fixed internal inputimpedance is 1.5 kΩ. The total gain of the limiting amplifiersection is approximately 96 dB. This IF limiting amplifiersection internally drives the quadrature detector section.
Fadj CURRENT (µA)
Figure 8. IF Amplifier Gainversus IF Frequency
f, FREQUENCY (MHz)
Figure 9. F adj Currentversus IF Frequency
Figure 10. F adj Voltageversus F adj Current
Figure 11. BW adj Currentversus IF Frequency
50
45
35
30
25
200.01 0.1 1.0 10
f, IF FREQUENCY (kHz)
120
0
100
80
60
40
20
0200 400 600 800 1000
VCC = 3.0 VdcSlope at 455 kHz = 9.26 kHz/µA
800
750
700
650
6000 20 40 60 80 100
f, IF FREQUENCY (kHz)
VCC = 3.0 VdcTA = 25°C
3.5
3.0
2.5
2.0
1.5
1.0
0400 420 440 460 480 500
0.5
40
Vin = 100 µVRin = 50 ΩRout = 1.4 kΩBW (3.0 dB) = 2.4 MHzTA = 25°C
IF A
MP
GAI
N (d
B)
VCC = 3.0 VdcBW 26 kHz/µA
FA
)µ
adjC
UR
REN
T (
F adj
VOLT
AGE
(mVd
c)
BWA)
µad
jCU
RR
ENT
(
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 7: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/7.jpg)
MC13150
7MOTOROLA ANALOG IC DEVICE DATA
Coilless DetectorThe quadrature detector is similar to a PLL. There is an
internal oscillator running at the IF frequency and twodetector outputs. One is used to deliver the audio signal andthe other one is filtered and used to tune the oscillator.
The oscillator frequency is set by an external resistor atthe Fadj pin. Figure 9 shows the control current required for aparticular frequency; Figure 10 shows the pin voltage at thatcurrent. From this the value of RF is chosen. For example,455 kHz would require a current of around 50 µA. The pinvoltage (Pin 16 in the 32 pin QFP package) is around 655mVgiving a resistor of 13.1 kΩ. Choosing 12 kΩ as the neareststandard value gives a current of approximately 55 µA. The5.0 µA difference can be taken up by the tuning resistor, RT.
The best nominal frequency for the AFTout pin (Pin 17)would be half supply. A supply voltage of 3.0 Vdc suggests aresistor value of (1.5 – 0.655)V/5.0 µA = 169 kΩ. Choosing150 kΩ would give a tuning current of 3/150 k = 20 µA. FromFigure 9 this would give a tuning range of roughly 10 kHz/µAor ± 100 kHz which should be adequate.
The bandwidth can be adjusted with the help of Figure 11.For example, 1.0 µA would give a bandwidth of ± 13 kHz. The
voltage across the bandwidth resistor, RB from Figure 12 isVCC – 2.44 Vdc = 0.56 Vdc for VCC = 3.0 Vdc, soRB = 0.56V/1.0 µA = 560 kΩ. Actually the locking range willbe ±13 kHz while the audio bandwidth will be approximately±8.4 kHz due to an internal filter capacitor. This is verified inFigure 13. For some applications it may be desirable that theaudio bandwidth is increased; this is done by reducing RB.Reducing RB widens the detector bandwidth and improvesthe distortion at high input levels at the expense of 12 dBSINAD sensitivity. The low frequency 3.0dB point is set by thetuning circuit such that the product
RTCT = 0.68/f3dB.
So, for example, 150 k and 1.0 µF give a 3.0 dB point of4.5 Hz. The recovered audio is set by RL to give roughly50mV per kHz deviation per 100 k of resistance. The dc levelcan be shifted by RS from the nominal 0.68 V by the followingequation:
Detector DC Output = ((RL + RS)/RS) 0.68 Vdc
Thus, RS = RL sets the output at 2 x 0.68 = 1.36 V;RL = 2RS sets the output at 3 x 0.68 = 2.0 V.
Figure 12. BW adj Currentversus BW adj Voltage
BWadj VOLTAGE (Vdc)
Figure 13. Demodulator Outputversus Frequency
2.3 2.5 2.7
f, FREQUENCY (kHz)
0.1 1.0 10 100
DEM
OD
ULA
TOR
OU
TPU
T (d
B)
10–3
10–4
10–5
10–6
10–7
VCC = 3.0 VdcTA = 25°C
10
0
–10
–20
–30
–50
–40
VCC = 3.0 VdcTA = 25°CfRF = 50 MHzfLO = 50.455 MHzLO Level = –10 dBmNo IF Bandpass Filtersfdev = ±4.0 kHz
RB = 560 k
RB = 1.0 M
BWad
jCU
RR
ENT
(A)
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 8: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/8.jpg)
MC13150
8 MOTOROLA ANALOG IC DEVICE DATA
APPLICATIONS INFORMATION
Evaluation PC BoardThe evaluation PCB is very versatile and is intended to be
used across the entire useful frequency range of this device.The center section of the board provides an area forattaching all SMT components to the circuit side and radialleaded components to the component ground side (seeFigures 29 and 30). Additionally, the peripheral areasurrounding the RF core provides pads to add supportingand interface circuitry as a particular application dictates.There is an area dedicated for a LNA preamp. Thisevaluation board will be discussed and referenced in thissection.
Component SelectionThe evaluation PC board is designed to accommodate
specific components, while also being versatile enough touse components from various manufacturers and coil types.The applications circuit schematic (Figure 15) specifiesparticular components that were used to achieve the resultsshown in the typical curves but equivalent componentsshould give similar results. Component placement views are
shown in Figures 27 and 28 for the application circuit inFigure 15 and for the 83.616 MHz crystal oscillator circuit inFigure 16.
Input Matching ComponentsThe input matching circuit shown in the application circuit
schematic (Figure 15) is a series L, shunt C single L sectionwhich is used to match the mixer input to 50 Ω. Analternative input network may use 1:4 surface mounttransformers or BALUNs. The 12 dB SINAD sensitivityusing the 1:4 impedance transformer is typically –100 dBmfor fmod = 1.0 kHz and fdev = ±5.0 kHz at fin = 50 MHz andfLO = 50.455 MHz (see Figure 14).
It is desirable to use a SAW filter before the mixer toprovide additional selectivity and adjacent channel rejectionand improved sensitivity. SAW filters sourced from Toko(Part # SWS083GBWA) and Murata (Part # SAF83.16MA51X)are excellent choices to easily interface with the MC13150mixer. They are packaged in a 12 pin low profile surfacemount ceramic package. The center frequency is 83.161 MHzand the 3.0 dB bandwidth is 30 kHz.
Figure 14. S+N+D, N+D, N, 30% AMRversus Input Signal Level
INPUT SIGNAL (dBm)
–120
S+N
+D, N
+D, N
, 30%
AM
R (d
B)
20
–60
VCC = 3.0 Vdcfmod = 1.0 kHzfdev = ±5.0 kHzfin = 50 MHz
–50
–40
–30
–20
–10
0
10
–100 –80 –60 –40
fLO = 50.455 MHzLO Level = –10 dBmSee Figure 15
S+N+D
N+D
30% AMR
N
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 9: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/9.jpg)
MC13150
9MOTOROLA ANALOG IC DEVICE DATA
Figure 15. Application Circuit
NOTES: 1. Alternate solution is 1:4 impedance transformer (sources include Mini Circuits, Coilcraft and Toko).2. 455 kHz ceramic filters (source Murata CFU455 series which are selected for various bandwidths).3. For external LO source, a 51 Ω pull–up resistor is used to bias the base of the on–board transistor as shown in Figure 15.
Designer may provide local oscillator with 3rd, 5th, or 7th overtone crystal oscillator circuit. The PC board is laid out toaccommodate external components needed for a Butler emitter coupled crystal oscillator (see Figure 16).
4. Enable IC by switching the pin to VEE.5. The resistor is chosen to set the range of RSSI voltage output swing.6. Details regarding the external components to setup the coilless detector are provided in the application section.
32 31 30 29 28 27 26 25
9 10 11 12 13 14 15 16
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
(3)LO Input
(4)Enable(5)RSSI
RSSIBuffer
DetectorOutput
RL150 k
RS150 k
1.0 n
100 n
100 n
1.0 µCT
+
560 kRB
150 kRT
12 kRF
(6)Coilless Detector
Circuit
10 µ
VCC
100 n
100 n455 kHzIF Ceramic
Filter
1.0 n
1.0 n100 n
(2)455 kHz
IF CeramicFilter
100 n
RF/IFInput
11 p
(1)180 nH
100 n 51
82 k
VEE1
Mixer
VCC1
LocalOscillator
RSSIBuffer
IF
VCC2
VEE2
Limiter
(6)
Det
ecto
r
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 10: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/10.jpg)
MC13150
10 MOTOROLA ANALOG IC DEVICE DATA
Local Oscillators
HF & VHF ApplicationsIn the application schematic, an external sourced local
oscillator is utilized in which the base is biased via a 51 Ωresistor to VCC. However, the on–chip grounded collectortransistor may be used for HF and VHF local oscillators withhigher order overtone crystals. Figure 16 shows a 5thovertone oscillator at 83.616 MHz. The circuit uses a Butlerovertone oscillator configuration. The amplifier is an emitterfollower. The crystal is driven from the emitter and is coupledto the high impedance base through a capacitive tapnetwork. Operation at the desired overtone frequency isensured by the parallel resonant circuit formed by thevariable inductor and the tap capacitors and parasiticcapacitances of the on–chip transistor and PC board. Thevariable inductor specified in the schematic could bereplaced with a high tolerance, high Q ceramic or air woundsurface mount component if the other components have tightenough tolerances. A variable inductor provides anadjustment for gain and frequency of the resonant tankensuring lock up and start–up of the crystal oscillator. Theovertone crystal is chosen with ESR of typically 80 Ω and120 Ω maximum; if the resistive loss in the crystal is too highthe performance of oscillator may be impacted by lower gainmargins.
A series LC network to ac ground (which is VCC) iscomprised of the inductance of the base lead of the on–chiptransistor and PC board traces and tap capacitors. Parasiticoscillations often occur in the 200 to 800 MHz range. A smallresistor is placed in series with the base (Pin 28) to cancel thenegative resistance associated with this undesired mode ofoscillation. Since the base input impedance is so large, asmall resistor in the range of 27 to 68 Ω has very little effecton the desired Butler mode of oscillation.
The crystal parallel capacitance, Co, provides a feedbackpath that is low enough in reactance at frequencies of 5thovertones or higher to cause trouble. Co has little effect nearresonance because of the low impedance of the crystalmotional arm (Rm–Lm–Cm). As the tunable inductor, whichforms the resonant tank with the tap capacitors, is tuned offthe crystal resonant frequency, it may be difficult to tell if theoscillation is under crystal control. Frequency jumps mayoccur as the inductor is tuned. In order to eliminate thisbehavior an inductor, Lo, is placed in parallel with the crystal.Lo is chosen to resonant with the crystal parallel capacitance,Co, at the desired operation frequency. The inductor providesa feedback path at frequencies well below resonance;however, the parallel tank network of the tap capacitors andtunable inductor prevent oscillation at these frequencies.
Figure 16. MC13150FTB Overtone OscillatorfRF = 83.16 MHz; fLO = 83.616 MHz
5th Overtone Crystal Oscillator
MC13150
Mixer
VEE
28
33
(4)0.135 µH
39 p
27 k10 n
1.0 µH
VCC
(3)5th OTXTAL
+
29
31
1.0 µ
39 p
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 11: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/11.jpg)
MC13150
11MOTOROLA ANALOG IC DEVICE DATA
Receiver Design ConsiderationsThe curves of signal levels at various portions of the
application receiver with respect to RF input level are shownin Figure 17. This information helps determine the networktopology and gain blocks required ahead of the MC13150 toachieve the desired sensitivity and dynamic range of thereceiver system. The PCB is laid out to accommodate a lownoise preamp followed by the 83.16 MHz SAW filter. In the
application circuit (Figure 15), the input 1.0 dB compressionpoint is –10 dBm and the input third order intercept (IP3)performance of the system is approximately 0 dBm (seeFigure 18).
Typical Performance Over TemperatureFigures 19–26 show the device performance over
temperature.
Figure 17. Signal Levels versusRF Input Signal Level
RF INPUT SIGNAL LEVEL (dBm)
–80
POW
ER (d
Bm)
10
–70
–50
–40
–30
–20
–10
0
–70 –60 –50 –40
fRF = 50 MHzfLO = 50.455 MHz; LO Level = –10 dBmSee Figure 15
IF Output
–60
Mixer Output
LimiterInput
IF Input
MixerInput
RF Inputat TransformerInput
–30 –20 –10 0
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 12: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/12.jpg)
MC13150
12 MOTOROLA ANALOG IC DEVICE DATA
Figure 18. 1.0 dB Compression Point and InputThird Order Intercept Point versus Input Power
RF INPUT POWER (dBm)
MIX
ER IF
OU
TPU
T LE
VEL
(dBm
)
20
–40
–20
0
–60
–80 –60 –40 –20 0 20
VCC = 3.0 VdcfRF1 = 50 MHzfRF2 = 50.01 MHzfLO = 50.455 MHzPLO = –10 dBmSee Figure 15
1.0 dB CompressionPoint = –11 dBm
IP3 = –0.5 dBm
TYPICAL PERFORMANCE OVER TEMPERATURE
SIGNAL INPUT LEVEL (dBm)
Figure 19. Supply Current, I VEE1versus Signal Input Level
Figure 20. Supply Current, I VEE2versus Ambient Temperature
5.0
0
TA, AMBIENT TEMPERATURE (°C)
0.35
0.3
0.25
0.2
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
–120 –105 –90 –75 –60 –45 –30 –15 0
VCC = 3.0 Vdcfc = 50 MHzfdev = ±4.0 kHz
TA = 85°C
TA = 25°C TA = –40°C
–40 –20 0 20 40 60 80
VCC = 3.0 Vdc
I VEE
1, S
UPP
LY C
UR
REN
T (m
A)
I VEE
2, S
UPP
LY C
UR
REN
T (m
A)
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 13: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/13.jpg)
MC13150
13MOTOROLA ANALOG IC DEVICE DATA
TYPICAL PERFORMANCE OVER TEMPERATURE
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 21. Total Supply Currentversus Ambient Temperature
TA, AMBIENT TEMPERATURE (°C)
Figure 22. Minimum Supply Voltageversus Ambient Temperature
Figure 23. RSSI Current versusAmbient Temperature and Signal Level
Figure 24. Recovered Audio versusAmbient Temperature
Figure 25. Demod DC Output Voltageversus Ambient Temperature
Figure 26. LO Current versusAmbient Temperature
1.8
1.75
1.7
1.65
1.6
1.4
TA, AMBIENT TEMPERATURE (°C)
3.0
2.5
2.0
1.5
1.0
60
50
40
30
20
10
0
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
0.7
0.65
0.6
0.55
0.5
0.4
0.45
1.7
1.6
1.5
1.4
0.9
1.3
–40 –20 0 20 40 60 80
100
90
80
70
50
60
TOTA
L SU
PPLY
CU
RR
ENT
(mA)
MIN
IMU
M S
UPP
LY V
OLT
AGE
(Vdc
)
DEM
OD
DC
OU
TPU
T VO
LTAG
E (V
dc)
1.55
1.5
1.45
–40 –20 0 20 40 60 80 –40 –20 0 20 40 60 80
–40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100
1.2
1.1
1.0
–40 –20 0 20 40 60 80
VCC = 3.0 Vdc
VCC = 3.0 VdcfRF = 50 MHz
Vin =
0 dBm–20 dBm
–40 dBm
–60 dBm
–80 dBm
–100 dBm
–120 dBm
VCC = 3.0 VdcRF In = –50 dBmfc = 50 MHzfLO = 50.455 MHzfdev = ±4.0 kHz
VCC = 3.0 VdcRF In = –50 dBmfc = 50 MHzfLO = 50.455 MHzfdev = ±4.0 kHz
VCC = 3.0 VdcRF In = –50 dBmfc = 50 MHzfLO = 50.455 MHzfdev = ±4.0 kHz
REC
OVE
RED
AU
DIO
(Vpp
)LO
CU
RR
ENT
(A)µ
RSS
I CU
RR
ENT
(A)µ
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 14: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/14.jpg)
MC13150
14 MOTOROLA ANALOG IC DEVICE DATA
Figure 27. Component Placement View – Circuit Side
GND VCC
1 n
150 k
100 n
27 k
1 n
100 n
1 n
150 k
1 n
100 n
10 n33
39 p
180 n
11 p 1 n
82 k
150 k
100 n
560 k
12 k
39 p
1µ
100 n
10µ
+
50Sem
i–Rigid C
oaxΩ
MC13150FTB
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 15: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/15.jpg)
MC13150
15MOTOROLA ANALOG IC DEVICE DATA
Figure 28. Component Placement View – Ground Side
455 kHzCeramic
Filter
455 kHzCeramic
Filter
RF1 IN RF2 IN
LO IN
LOTuning
Xtal
ENABLE
RSSI
AFT_adj
GND
BW_adj F_adj DET_out
VCC
455 kHzCeramic
Filter
1 µH
83.616 MHz
135 nH
SMA
455 kHzCeramic
Filter
3.8″AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 16: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/16.jpg)
MC13150
16 MOTOROLA ANALOG IC DEVICE DATA
Figure 29. PCB Circuit Side View
3.8″
MC13150 Rev 0 3/95
GND VCC
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 17: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/17.jpg)
MC13150
17MOTOROLA ANALOG IC DEVICE DATA
Figure 30. PCB Ground Side View
455 kHzCeramic
Filter
455 kHzCeramic
Filter
RF1 IN RF2 IN
LO IN
LOTuning
Xtal
ENABLE
RSSI
AFT_adj
GND
BW_adj F_adj DET_out
VCC
3.8″AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 18: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/18.jpg)
MC13150
18 MOTOROLA ANALOG IC DEVICE DATA
FTA SUFFIXPLASTIC PACKAGE
CASE 977–01(LQFP–24)ISSUE O
OUTLINE DIMENSIONS
DIM MIN MAX MIN MAXINCHESMILLIMETERS
A 4.000 BSC 0.157 BSCA1 2.000 BSC 0.079 BSCB 4.000 BSC 0.157 BSCB1 2.000 BSC 0.079 BSCC 1.400 1.600 0.055 0.063D 0.170 0.270 0.007 0.011E 1.350 1.450 0.053 0.057F 0.170 0.230 0.007 0.009G 0.500 BSC 0.020 BSCH 0.050 0.150 0.002 0.006J 0.090 0.200 0.004 0.008K 0.500 0.700 0.020 0.028M 12 REF 12 REFN 0.090 0.160 0.004 0.006P 0.250 BSC 0.010 BSCQ 1 5 1 5 R 0.150 0.250 0.006 0.010S 6.000 BSC 0.236 BSCS1 3.000 BSC 0.118 BSCV 6.000 BSC 0.236 BSCV1 3.000 BSC 0.118 BSCW 0.200 REF 0.008 REFX 1.000 REF 0.039 REF
NOTES:1 DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.2 CONTROLLING DIMENSION: MILLIMETER.3 DATUM PLANE –AB– IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEADWHERE THE LEAD EXITS THE PLASTIC BODY ATTHE BOTTOM OF THE PARTING LINE.
4 DATUMS –T–, –U–, AND –Z– TO BE DETERMINEDAT DATUM PLANE –AB–.
5 DIMENSIONS S AND V TO BE DETERMINED ATDATUM PLANE –AC–.
6 DIMENSIONS A AND B DO NOT INCLUDE MOLDPROTRUSION. ALLOWABLE PROTRUSION IS0.250 (0.010) PER SIDE. DIMENSIONS A AND B DOINCLUDE MOLD MISMATCH AND AREDETERMINED AT DATUM PLANE –AB–.
7 DIMENSION D DOES NOT INCLUDE DAMBARPROTRUSION. DAMBAR PROTRUSION SHALLNOT CAUSE THE D DIMENSION TO EXCEED0.350 (0.014).
8 MINIMUM SOLDER PLATE THICKNESS SHALL BE0.0076 (0.0003).
9 EXACT SHAPE OF EACH CORNER IS OPTIONAL.
DETAIL AD
DETAIL Y
4X
4X
1
6
7
13
19
12
18
24
S
S1
A
A1
–U–
T–U0.200 (0.008) ZAB9
B
B1
–T–
V
V1
–Z–
T–U0.200 (0.008) ZAB
–AC–
–AB–
0.080 (0.003) AC
R
DETAIL AD DETAIL Y
AE AE
K
X
W
G
TOP & BOTTOM
SECTION AE–AE
M
Q
C E
H0.250 (0.010)
GAUGEPLANE
ÉÉÉÉÉÉÉÉÉ
ÇÇÇÇÇÇÇÇÇ
F
D
NJ–T–, –U–, –Z–
P
ST–US0.080 (0.003) Z SAC
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 19: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/19.jpg)
MC13150
19MOTOROLA ANALOG IC DEVICE DATA
FTB SUFFIXPLASTIC PACKAGE
CASE 873–01(LQFP–32)ISSUE A
OUTLINE DIMENSIONS
0.2740.2740.0550.0100.0510.010
— 0.0050.013
6°0.005
5°0.0060.3480.006
5°0.348
MIN MINMAX MAXMILLIMETERS INCHES
DIM7.107.101.60
0.3731.50
—
0.200.1970.57
8°0.135
10°0.259.150.2511°9.15
6.956.951.40
0.2731.30
0.273
— 0.1190.33
6°0.119
5°0.158.850.155°
8.85
0.031 BSC
0.220 REF
0.016 BSC
0.80 BSC
5.6 REF
0.40 BSC
ABCDEFGHJKLMNPQRSTUVX
0.2800.2800.0630.0150.059
—
0.0080.0080.022
8°0.005
10°0.0100.3600.01011°
0.360
NOTES:1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.2. CONTROLLING DIMENSION: MILLIMETER.3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS
COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THEPLASTIC BODY AT THE BOTTOM OF THE PARTING LINE.
4. DATUMS -A-, -B- AND -D- TO BE DETERMINED AT DATUMPLANE -H-.
5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE-C-.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION.ALLOWABLE PROTRUSION IS 0.25 (0.010) PER SIDE.DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH ANDARE DETERMINED AT DATUM PLANE -H-.
7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION.ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003)TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUMMATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ONTHE LOWER RADIUS OR THE FOOT.
-H-DATUMPLANE
X
K
DETAIL C
U
T
R
Q
P
DETAIL A
-A-,-B-,-D-
B
B
J
BASE METAL
D
N
SECTION B-BVIEW ROTATED 90° CLOCKWISE
F
-H- DATUMPLANE
H
32
25
24 17
16
9
81
VB
-B-
L
-A-
L
-D-A
S
DETAIL A
-C-SEATINGPLANE
C E
DETAIL CM
MG
1.0 REF 0.039 REF
C0.20 (0.008) A–B DS SM
0.01 (0.004)
H0.20 (0.008) A–B DS SM
C0.20 (0.008) A–B D
A–B0.05 (0.002)
S SM0.
20 (0
.008
)C
A–B
D0.
05 (0
.002
)A–
B
MS
S
0.20
(0.0
08)
HA–
BD
MS
S
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5
![Page 20: MC13150 Technical Data Sheet - NXP Semiconductors · MC13150 MOTOROLA ANALOG IC DEVICE DATA 3 AC ELECTRICAL CHARACTERISTICS (continued) (TA = 25°C, VS = 3.0 Vdc, fRF = 50 MHz, fLO](https://reader034.vdocuments.us/reader034/viewer/2022050513/5f9d9760be1af32b3e12662d/html5/thumbnails/20.jpg)
MC13150
20 MOTOROLA ANALOG IC DEVICE DATA
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regardingthe suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, andspecifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motoroladata sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights ofothers. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or otherapplications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injuryor death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorolaand its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney feesarising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges thatMotorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an EqualOpportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.How to reach us:USA/EUROPE/Locations Not Listed : Motorola Literature Distribution; JAPAN : Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Customer Focus Center: 1–800–521–6274
Mfax : [email protected] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC : Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,Motorola Fax Back System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
– http://sps.motorola.com/mfax/HOME PAGE: http://motorola.com/sps/
MC13150/D◊
AR
CH
IVE
INF
OR
MA
TIO
N
AR
CH
IVE
INF
OR
MA
TIO
N
Fre
esc
ale
Se
mic
on
du
cto
r, I
Freescale Semiconductor, Inc.
For More Information On This Product, Go to: www.freescale.com
nc
...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MIC
ON
DU
CTO
R, I
NC
. 200
5