mazda glc1

Notes Specified value Measured value

Vehicle identificationNo. of cylinders Type 4/OHCCapacity (Fiscal) cc 1415 (1405)Compression ratio :1 9,0Suitable for unleaded petrol NoMinimum octane rating RON 91Ignition system Type SZIgnition system Description CBFuel System Description Carb-FJ

Ignition systemBallast resistance Ohm 1,5Primary resistance Ohm 1,6Firing order 1-3-4-2Distributor (ECM) Make MitsubishiContact breaker gap/trigger air gap mm 0,5Dwell angle (%) 49-55 (54-61)

Tuning and emissionsIgnition timing o = without + = with vacuum oIgnition timing - basic BTDC Engine/rpm 111/600

Ignition advance Without vacuum andbasic timingIgnition advance checks Engine/rpm 0/600Ignition advance checks Engine/rpm 10/2250Vacuum check + = advance o = retard +Vacuum range Engine 10-12Vacuum starts mbar 160Vacuum ends mbar 480Idle speed rpm 600-650Oil temperature for CO test C 60CO level at idle speed - tailpipe Vol. % CO 1,5-2,5HC level at idle speed ppm 500CO2 level at idle speed Vol. % CO2 13-16O2 level at idle speed Vol. % O2 0,5-2,0

Spark plugsSpark plugs Original equipment NGKSpark plug Type BPR6ESElectrode gap mm 0,8Spark plugs Make BoschSpark plug Type WR8DCElectrode gap mm 0,8Spark plugs Make ChampionSpark plug Type RN11YCCElectrode gap mm 0,8Spark plugs Make NGKSpark plug Type BPR6ESElectrode gap mm 0,8

Fuel systemFuel pump delivery pressure bar 0,2-0,27

Service checks and adjustmentsValve clearance -INLET mm 0,25 hotValve clearance -EXHAUST mm 0,30 hotCompression pressure bar 10-11Oil pressure bar/rpm 3,5-4,5

Manufacturer: Mazda Model: 323 (FA) 1,4 Engine code: UC1400 Output: 51 (70) 5700Tuned for: Year: 1979-81

Autodata Limited 200411/10/2008

V5.500-

Radiator cap bar 0,9Thermostat opens C 80-95Drive belt size - alternator mm 9,5x785Drive belt tension - alternator/PAS/AC mm 11-13

Lubricants and capacitiesEngine oil grade - moderate climate SAE 10W/40Engine oil classification API/ACEA SGEngine with filter litres 3Gearbox 4/5 speed litres 1,3Automatic transmission (drain & refill) litres 5,5Differential rear litres 1,0Cooling system litres 5,5

Tightening torquesCylinder head instructions

Cylinder headStage 1 Tighten 70-75 Nm

Other tightening torquesMain bearings Stage 1 30-32 NmMain bearings Stage 2 60-65 NmBig end bearings Stage 1 15-17 NmBig end bearings Stage 2 30-35 NmFlywheel/driveplate 80-90 NmSpark plugs 15-21 NmRoad wheels 90 Nm

Starting and chargingBattery V/RC(Ah) 12/55 (33)Starter motor Make MitsubishiStarter motor Type 0,8 kWMinimum starting voltage V 11,5Maximum cranking amps A 95-116Alternator/Regulator Make MitsubishiAlternator output at engine speed A/V/rpm 45/14,5/2500Regulated voltage V 14,0-15,0

Cylinder layout Timing mark



V5.500-

Idle speed adjustment (A) CO level adjustment (B)

Tightening sequence



V5.500-

mazda glc1

Documents