matv ultop fmu05e 5 - arrow conveyorarrowconveyor.com/pdf/regina-mat-top.pdf · 115 reduced chordal...
TRANSCRIPT
114
Installation guidelines
These belts are the ideal solution for applications where a head transfer of the conveyed products is preferred or required.
600 SERIES - ½” PITCH, LIGHT DUTY
600 series belts can be used together with magnetic or tab sideflexing chains 783 series (see pag. 123). Same thickness for easy installation side by side and standardization of wear strips.
Widths and guide shoes designed for installation on conveyors with 85 mm pitch between parallel tracks and 44 mm clearance between wear strips.
Head transfer of products: conveyor set-up guidelines
The dimensions shown below refer to the use of a 20mm roller for the head transfer and can normally be adopted.However, it is recommended that pre-production tests are carried out and adjustments are made as necessary to achieve successful product transfer.
For 90° products transfer, also availability of ATM (Active Transfer Modules) series (see pag. 118).
MODULAR PLASTIC BELTS
115
Reduced chordal effect
Vertical oscillation of the belt when engaging the sprocket is known as “chordal effect” and, if excessive, it can cause unstable products to fall during head transfer. The “chordal effect” is minimized due to the reduced pitch (½”) and the special design of the hinges.
FEATURES AND BENEFITS
High sliding surface area
The modules have the industry’s largest surface area to maxi-mize the wear resistance.
Easy assembly and disassembly
Retention clips can easily be moved from the side of the beltfor assembling and disassembling. Only a small movement is required and the clip remains in its pocket.
Reliable drive
The highly resistant cross section offered by the double row of teeth pockets ensures high drive capacity and long wear and fatigue life.
CHORDAL EFFECTonly 1,1mm with a 20mm roller
116
Shoe guide position Dedicated width:
This belt offers a smooth and completely closed surface to provide excellent support and minimize product tippage.Particularly suitable for conveyors where a head transfer of products is required.
600 SERIES - ½” PITCH, SOLID TOP DEDICATED WIDTHS AND MODULAR BELTS
Standard MaterialsProducts Ref. LW DK Solid top 600
Solid top with guide 600G
Belt widths: 85 mm (3.346’’) or wider in 85 mm increments - Pin material: PP- Polypropylene (PBT on request) - Working Load (at 25°C/77°F): 14000 N/m (960 lb/ft)
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW) REGINA DK BELT
WEIGHTREGINA REF. REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 kg/m lbs/ft
85 3.35 600B LW 0085 600BG LW 0085 600B DK 0085 600BG DK 0085 0.81 0.54
170 6.69 600B LW 0170 600BG LW 0170 600BG1 LW 0170 600B DK 0170 600BG DK 0170 600BG1 DK 0170 1,61 1.08
255 10.04 600B LW 0255 600BG LW 0255 600BG1 LW 0255 600B DK 0255 600BG DK 0255 600BG1 DK 0255 2,40 1.61
340 13.39 600B LW 0340 600BG LW 0340 600BG1 LW 0340 600B DK 0340 600BG DK 0340 600BG1 DK 0340 3,20 2.15
425 16.73 600B LW 0425 600BG LW 0425 600BG1 LW 0425 600B DK 0425 600BG DK 0425 600BG1 DK 0425 3,99 2.68
510 20.08 600B LW 0510 600BG LW 0510 600BG1 LW 0510 600B DK 0510 600BG DK 0510 600BG1 DK 0510 4,78 3.21
595 23.43 600B LW 0595 600BG LW 0595 600BG1 LW 0595 600B DK 0595 600BG DK 0595 600BG1 DK 0595 5,58 3.75
680 26.77 600B LW 0680 600BG LW 0680 600BG1 LW 0680 600B DK 0680 600BG DK 0680 600BG1 DK 0680 6,37 4.28
765 30.12 600B LW 0765 600BG LW 0765 600BG1 LW 0765 600B DK 0765 600BG DK 0765 600BG1 DK 0765 7,17 4.82
850 33.46 600B LW 0850 600BG LW 0850 600BG1 LW 0850 600B DK 0850 600BG DK 0850 600BG1 DK 0850 7,96 5.35
935 36.81 600B LW 0935 600BG LW 0935 600BG1 LW 0935 600B DK 0935 600BG DK 0935 600BG1 DK 0935 8,75 5.88
1020 40.16 600B LW 1020 600BG LW 1020 600BG1 LW 1020 600B DK 1020 600BG DK 1020 600BG1 DK 1020 9,55 6.42
1105 43.50 600B LW 1105 600BG LW 1105 600BG1 LW 1105 600B DK 1105 600BG DK 1105 600BG1 DK 1105 10,34 6.95
1190 46.85 600B LW 1190 600BG LW 1190 600BG1 LW 1190 600B DK 1190 600BG DK 1190 600BG1 DK 1190 11,14 7.49
1275 50.20 600B LW 1275 600BG LW 1275 600BG1 LW 1275 600B DK 1275 600BG DK 1275 600BG1 DK 1275 11,93 8.02
1360 53.54 600B LW 1360 600BG LW 1360 600BG1 LW 1360 600B DK 1360 600BG DK 1360 600BG1 DK 1360 12,73 8.56
1445 56.89 600B LW 1445 600BG LW 1445 600BG1 LW 1445 600B DK 1445 600BG DK 1445 600BG1 DK 1445 13,52 9.09
1530 60.24 600B LW 1530 600BG LW 1530 600BG1 LW 1530 600B DK 1530 600BG DK 1530 600BG1 DK 1530 14,13 9.50 Belts wider than 1530 mm available (increments of 85 mm). Example: 1530+85=1615 mm width, without guide Ref. (in LW material) 600B LW 1615.
Standard length for belts up to a width of 680 mm: 3,048 m (10 feet). Wider belts available in any requested length.
Sprockets and Idlerwheels see pages 219÷223
Belt materialsee page 13
Sprocket positioning see pages 302÷303
600 (Solid top - ½” Pitch)
G version
G1 version
Modular belt:
Dimension mm inches A 6 .236 B 8 .315 C 63,5 2.5 E 4,6 .181 G 42 1.654 L 4,35 .171 P 12,7 .5 RD 20 .787 T 8,7 .343 GC 44 1.732
117
BELT NOMINAL WIDTH “W”
POLYPROPYLENE *(PP)BELT
WEIGHTREGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 kg/m lbs/ft
85 3.35 600B PP 0085 600BG PP 0085 0,56 0.38
170 6.69 600B PP 0170 600BG PP 0170 600BG1 PP 0170 1,10 0.74
255 10.04 600B PP 0255 600BG PP 0255 600BG1 PP 0255 1,64 1.10
340 13.39 600B PP 0340 600BG PP 0340 600BG1 PP 0340 2,18 1.47
425 16.73 600B PP 0425 600BG PP 0425 600BG1 PP 0425 2,72 1.83
510 20.08 600B PP 0510 600BG PP 0510 600BG1 PP 0510 3,25 2.18
595 23.43 600B PP 0595 600BG PP 0595 600BG1 PP 0595 3,79 2.55
680 26.77 600B PP 0680 600BG PP 0680 600BG1 PP 0680 4,33 2.91
765 30.12 600B PP 0765 600BG PP 0765 600BG1 PP 0765 4,87 3.27
850 33.46 600B PP 0850 600BG PP 0850 600BG1 PP 0850 5,41 3.64
935 36.81 600B PP 0935 600BG PP 0935 600BG1 PP 0935 5,94 3.99
1020 40.16 600B PP 1020 600BG PP 1020 600BG1 PP 1020 6,48 4.36
1105 43.50 600B PP 1105 600BG PP 1105 600BG1 PP 1105 7,02 4.72
1190 46.85 600B PP 1190 600BG PP 1190 600BG1 PP 1190 7,56 5.08
1275 50.20 600B PP 1275 600BG PP 1275 600BG1 PP 1275 8,10 5.45
1360 53.54 600B PP 1360 600BG PP 1360 600BG1 PP 1360 8,63 5.80
1445 56.89 600B PP 1445 600BG PP 1445 600BG1 PP 1445 9,17 6.16
1530 60.24 600B PP 1530 600BG PP 1530 600BG1 PP 1530 9,71 6.53 Belts wider than 1530 mm available (increments of 85 mm) Example: 1530+85=1615 mm width, without guide Ref. (in PP material) 600B PP 1615.*Due to different shrinkage of materiales, actual width is larger than the standard.
Standard length for belts up to a width of 680 mm: 3,048 m (10 feet). Wider belts available in any requested length.
600 (Solid top - ½” Pitch)
Shoe guide position Dedicated width:
G version
G1 version
Modular belt:
This belt offers a smooth and completely closed surface to provide excellent support and minimize product tippage.Particularly suitable for conveyors where a head transfer of products is required.
600 SERIES - ½” PITCH, SOLID TOP DEDICATED WIDTHS AND MODULAR BELTS
Standard MaterialsProducts Ref. *PP Solid top 600 Solid top with guide 600G
Belt widths: 85 mm (3.346’’) or wider in 85 mm increments - Pin material: PP- Polypropylene (PBT on request) - Working Load (at 25°C/77°F): 10000 N/m (685 lb/ft)
Dimension mm inches A 6 .236 B 8 .315 C 63,5 2.5 E 4,6 .181 G 42 1.654 L 4,35 .171 P 12,7 .5 RD 20 .787 T 8,7 .343 GC 44 1.732
Sprockets and Idlerwheels see pages 219÷223
Belt materialsee page 13
Sprocket positioning see pages 302÷303
118
Active transfer modules 600GATM series allow the transfer of the products between two 90° conveyor tracks without using dead plates.Available left and right version
Standard MaterialsProducts Ref. LW DK *PPSolid top with guide 600GATM
Pin material: PP - Polypropylene
600 SERIES - ½ PITCH‚ SOLID TOP
600GATM (Solid top - Right Version)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) 600BGATM LW 0085 DX 110 4.33 8,7 0.34 1190 268 0,97 0.65
REGINA DK 600BGATM DK 0085 DX 110 4.33 8,7 0.34 1190 268 0,97 0.65
Standard length: 3,048 m (10 feet)
600GATM (Solid top - Left Version)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) 600BGATM LW 0085 SX 110 4.33 8,7 0.34 1190 268 0,97 0.65
REGINA DK 600BGATM DK 0085 SX 110 4.33 8,7 0.34 1190 268 0,97 0.65
Example (in PP material, Right version): 600BGATM PP 0085 DX.*Due to different shrinkage of materials, actual width is larger than the standard.
Standard length :3,048 m (10 feet)
Right Version
600 SERIESNEW
ACTIVE TRANSFER MODULES
Left Version
Dimension mm inches A 6 .236 B 8 .315 C 21,3 .839 D 25,4 1 E 4,6 .181 G 42 1.654 L 4,35 .171 P 12,7 .5 RD 20 .787 GC 44 1.732
Sprockets and Idlerwheels see pages 219÷223
Belt materialsee page 13
Sprocket positioningsee pages 302-304
Sprockets and Idlerwheels see pages 219÷223
Belt materialsee page 13
Sprocket positioningsee pages 302-304
119
1500 AND 1600 SERIES - 1” PITCH, LIGHT DUTY
Installation guidelines
Widths and guides are designed for installation on conveyors with 85 mm pitch between parallel tracks and 44 mm clearancebetween the wear strips.
These belts can be used on conveyors side by side with magnetic or tab sideflexing chains 782 or 783 series (see pag. 123). Same thickness of 8,7 mmfor easy installation side by side and standardization of wear strips. For 90° products transfer, also availability of ATM (Active Trasfer Modules) series (see pag. 126÷127)
Gentle product handling
The extremely good flatness, the manufacturing accuracy, the reduced side gaps on conveyors and the availability of materials with extremely low friction coefficients make these belts suitable for high efficiency lines with unstable products.
9mm
Smooth and uniform surface
The surface near the edge of the modules is uniform,with no discontinuities, thus the side transfer of products is not disturbed.
Easy assembly and disassembly
Retention clips can easily be moved from the side of the belt for assembling and disassembling. Only a small movement is required, the clip remains in the module.
Reliable drive
The accurate tooth profile with a large cross section ensures high drive capacity and long wear life of sprocketsand modules. The central pocket makes these belts bidirectional.
Features and Benefits
MODULAR PLASTIC BELTS
120
1600 SERIES - 1” PITCH, SOLID TOP
Extremely good flatness, manufacturing accuracy, and low coefficient of friction, make the side transfer of the products very easy.Completely closed surface, no gap between the modules, evenwhen engaging on the sprockets.Particularly suitable for glass products, small sized products and unstable containers (for example PET bottles with petaloid base).
83,8 mm wide chains available for gap reduction on 85 mm transversal pitch conveyors. Particularly suitable for inliners.
Standard MaterialsProducts Ref. LW DK *PPSolid top with guide 1600G
Pin material: PBT
1600 (Solid top – 1” Pitch)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW)1600AG LW K 3¼ 82,6 3.25 8,7 0.34 1850 415 0,64 0.43
1600AG LW K 83,8 83,8 3.30 8,7 0.34 1850 415 0,66 0.44
REGINA DK1600AG DK K 3¼ 82,6 3.25 8,7 0.34 1850 415 0,64 0.43
1600AG DK K 83,8 83,8 3.30 8,7 0.34 1850 415 0,66 0.44
*Due to different shrinkage of materials, actual width is larger than the standard. Standard length: 3,048 m (10 feet)
onrequest
1600 NEW
DEDICATED WIDTHS
Dimension mm inches A 6,7 .264 B 4,4 .173 C 21,3 .839 E 4,6 .181 G 42 1.654 L 4,35 .171 P 25,4 1 RD 20 .787 GC 44 1.732
Sprockets and Idlerwheels see pages 224÷227
Belt materialsee page 13
Sprocket positioningsee pages 305÷306
121
1600 SERIES - 1” PITCH, SOLID TOP
This belt offers a smooth surface to provide excellent supportand minimize product tippage.Particularly suitable for glass products, small sized productsand unstable containers (for example PET bottles with petaloid base).
onrequest
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW) REGINA DKBELT
WEIGHTREGINA REF. REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 kg/m lbs/ft
85 3.35 1600A LW 0085 1600AG LW 0085 1600A DK 0085 1600AG DK 0085 0,67 0.45
170 6.69 1600B LW 0170 1600BG LW 0170 1600BG1 LW 0170 1600B DK 0170 1600BG DK 0170 1600BG1 DK 0170 1,29 0.87
255 10.04 1600B LW 0255 1600BG LW 0255 1600BG1 LW 0255 1600B DK 0255 1600BG DK 0255 1600BG1 DK 0255 1,93 1.30
340 13.39 1600B LW 0340 1600BG LW 0340 1600BG1 LW 0340 1600B DK 0340 1600BG DK 0340 1600BG1 DK 0340 2,57 1.73
425 16.73 1600B LW 0425 1600BG LW 0425 1600BG1 LW 0425 1600B DK 0425 1600BG DK 0425 1600BG1 DK 0425 3,20 2.15
510 20.08 1600B LW 0510 1600BG LW 0510 1600BG1 LW 0510 1600B DK 0510 1600BG DK 0510 1600BG1 DK 0510 3,84 2.58
595 23.43 1600B LW 0595 1600BG LW 0595 1600BG1 LW 0595 1600B DK 0595 1600BG DK 0595 1600BG1 DK 0595 4,47 3.00
680 26.77 1600B LW 0680 1600BG LW 0680 1600BG1 LW 0680 1600B DK 0680 1600BG DK 0680 1600BG1 DK 0680 5,11 3.43
765 30.12 1600B LW 0765 1600BG LW 0765 1600BG1 LW 0765 1600B DK 0765 1600BG DK 0765 1600BG1 DK 0765 5,75 3.86
850 33.46 1600B LW 0850 1600BG LW 0850 1600BG1 LW 0850 1600B DK 0850 1600BG DK 0850 1600BG1 DK 0850 6,38 4.29
935 36.81 1600B LW 0935 1600BG LW 0935 1600BG1 LW 0935 1600B DK 0935 1600BG DK 0935 1600BG1 DK 0935 7,02 4.72
1020 40.16 1600B LW 1020 1600BG LW 1020 1600BG1 LW 1020 1600B DK 1020 1600BG DK 1020 1600BG1 DK 1020 7,66 5.15
1105 43.50 1600B LW 1105 1600BG LW 1105 1600BG1 LW 1105 1600B DK 1105 1600BG DK 1105 1600BG1 DK 1105 8,29 5.57
1190 46.85 1600B LW 1190 1600BG LW 1190 1600BG1 LW 1190 1600B DK 1190 1600BG DK 1190 1600BG1 DK 1190 8,93 6.00
1275 50.20 1600B LW 1275 1600BG LW 1275 1600BG1 LW 1275 1600B DK 1275 1600BG DK 1275 1600BG1 DK 1275 9,56 6.43
1360 53.54 1600B LW 1360 1600BG LW 1360 1600BG1 LW 1360 1600B DK 1360 1600BG DK 1360 1600BG1 DK 1360 10,20 6.86
1445 56.89 1600B LW 1445 1600BG LW 1445 1600BG1 LW 1445 1600B DK 1445 1600BG DK 1445 1600BG1 DK 1445 10,84 7.29
1530 60.24 1600B LW 1530 1600BG LW 1530 1600BG1 LW 1530 1600B DK 1530 1600BG DK 1530 1600BG1 DK 1530 11,47 7.71
Standard MaterialsProducts Ref. LW DK *PPSolid top 1600Solid top with guide 1600G
Belt widths: 85 mm (3.346’’) or wider in 85 mm increments - Pin material: PBT (dedicated width) PP- Polypropylene (Modular belts) (PBT on request) - Working Load (at 25°C/77°F): 21600 N/m (1,480 lb/ft) (for LW and DK materials)
Belts wider than 1530 mm available (increments of 85 mm) Example: 1530+85=1615 mm width, without guide Ref. (in LW material) 1600B LW 1615.*Due to different shrinkage of materials, actual width is larger than the standard.
Standard length for belts up to a width of 680 mm: 3,048 m (10 feet). Wider belts available in any requested length.
1600 (Solid top – 1” Pitch)
Shoe guide positionDedicated width:
Modular belt:
G version
G1 version
MODULAR BELTS
Dimension mm inches A 6,7 .264 B 4,4 .173 C 63,5 2.5 E 4,6 .181 G 42 1.654 L 4,35 .171 P 25,4 .1 RD 20 .787 T 8,7 .343 GC 44 1.732
Sprockets and Idlerwheels see pages 224÷227
Belt materialsee page 13
Sprocket positioning see pages 305÷306
122
1500 SERIES - 1” PITCH, FLUSH GRID
This belt has an excellent combination of open and support areas to allow drainage of liquids and good support of the conveyed products. This belt is particularly suitable for conveying of aluminium cans.
Standard MaterialsProducts Ref. LW DK *PPFlush grid 1500
Flush grid with guide 1500G
Belt widths: 85 mm (3.346’’) or wider in 85 mm increments 82,6 mm (3.25”) dedicated width also available - Pin material: PBT (dedicated width) PP- Polypropylene (Modular belts) (PBT on request) - Working Load (at 25°C/77°F): 21600 N/m (1,480 lb/ft) (for LW and DK materials) - Open surface: 31%
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW) REGINA DKBELT
WEIGHTREGINA REF. REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 kg/m lbs/ft
82,6 3.25 1500A LW K 3¼ 1500AG LW K 3¼ 1500A DK K 3¼ 1500AG DK K 3¼ 0,56 0.38
85 3.35 1500A LW 0085 1500AG LW 0085 1500A DK 0085 1500AG DK 0085 0,59 0.40
170 6.69 1500B LW 0170 1500BG LW 0170 1500BG1 LW 0170 1500B DK 0170 1500BG DK 0170 1500BG1 DK 0170 1,20 0.81
255 10.04 1500B LW 0255 1500BG LW 0255 1500BG1 LW 0255 1500B DK 0255 1500BG DK 0255 1500BG1 DK 0255 1,67 1.12
340 13.39 1500B LW 0340 1500BG LW 0340 1500BG1 LW 0340 1500B DK 0340 1500BG DK 0340 1500BG1 DK 0340 2,20 1.48
425 16.73 1500B LW 0425 1500BG LW 0425 1500BG1 LW 0425 1500B DK 0425 1500BG DK 0425 1500BG1 DK 0425 2,76 1.86
510 20.08 1500B LW 0510 1500BG LW 0510 1500BG1 LW 0510 1500B DK 0510 1500BG DK 0510 1500BG1 DK 0510 3,31 2.22
595 23.43 1500B LW 0595 1500BG LW 0595 1500BG1 LW 0595 1500B DK 0595 1500BG DK 0595 1500BG1 DK 0595 3,85 2.59
680 26.77 1500B LW 0680 1500BG LW 0680 1500BG1 LW 0680 1500B DK 0680 1500BG DK 0680 1500BG1 DK 0680 4,40 2.96
765 30.12 1500B LW 0765 1500BG LW 0765 1500BG1 LW 0765 1500B DK 0765 1500BG DK 0765 1500BG1 DK 0765 4,94 3.32
850 33.46 1500B LW 0850 1500BG LW 0850 1500BG1 LW 0850 1500B DK 0850 1500BG DK 0850 1500BG1 DK 0850 5,49 3.69
935 36.81 1500B LW 0935 1500BG LW 0935 1500BG1 LW 0935 1500B DK 0935 1500BG DK 0935 1500BG1 DK 0935 6,03 4.05
1020 40.16 1500B LW 1020 1500BG LW 1020 1500BG1 LW 1020 1500B DK 1020 1500BG DK 1020 1500BG1 DK 1020 6,58 4.42
1105 43.50 1500B LW 1105 1500BG LW 1105 1500BG1 LW 1105 1500B DK 1105 1500BG DK 1105 1500BG1 DK 1105 7,13 4.79
1190 46.85 1500B LW 1190 1500BG LW 1190 1500BG1 LW 1190 1500B DK 1190 1500BG DK 1190 1500BG1 DK 1190 7,67 5.16
1275 50.20 1500B LW 1275 1500BG LW 1275 1500BG1 LW 1275 1500B DK 1275 1500BG DK 1275 1500BG1 DK 1275 8,22 5.52
1360 53.54 1500B LW 1360 1500BG LW 1360 1500BG1 LW 1360 1500B DK 1360 1500BG DK 1360 1500BG1 DK 1360 8,76 5.89
1445 56.89 1500B LW 1445 1500BG LW 1445 1500BG1 LW 1445 1500B DK 1445 1500BG DK 1445 1500BG1 DK 1445 9,31 6.26
1530 60.24 1500B LW 1530 1500BG LW 1530 1500BG1 LW 1530 1500B DK 1530 1500BG DK 1530 1500BG1 DK 1530 9,86 6.63
Shoe guide position Dedicated width:
Modular belt:
G version
G1 version
Belts wider than 1530 mm available (increments of 85 mm) Example: 1530+85=1615 mm width, without guide Ref. (in LW material) 1500B LW 1615.*Due to different shrinkage of materials, actual width is larger than the standard.
Standard length for belts up to a width of 680 mm: 3,048 m (10 feet). Wider belts available in any requested length.
1500 (Flush grid – 1” Pitch)
Dimension mm inches A 6,7 .264 B 4,4 .173 C 63,5 2.5 E 4,6 .181 G 42 1.654 L 4,35 .171 P 25,4 1 RD 20 .787 T 8,7 .343 GC 44 1.732
DEDICATED WIDTHS AND MODULAR BELTS
onrequest
Sprockets and Idlerwheels see pages 224÷227
Belt materialsee page 13
Sprocket positioning see pages 305÷306
123
783T, 782M AND 783M SERIES - 1” PITCH LIGHT DUTY
Installation guidelines
Matveyor® sideflexing chains 783T, 782M and 783M can be used on conveyors side by side with Matveyor® belts 600 series and 1500/1600 series.Same thickness of 8,7mm for easy installation side by side and standardization of wear strips.
Tab chains 783T use the same curves as Flitetop® plastic chains 880T, 879T and Flitetop® steel chains 881T and 981T.(For tab curves see pag. 280)
Magnetic chains 782M and 783M have no tab or bevel profile and have been designed to be installed on magnetic curves.(For magnetic curves see pag. 238)
Gentle product handling
The small 1” pitch top-plate combination results in a very low gap between flights. Availability of materials with extremely low friction coefficients (see page 13).
reduced gap
Features and Benefits
Standardization in conveyor construction
Easy installation side by side with Matveyor® belts.
SIDEFLEXING CHAINS
124
783T SERIES - 1” PITCH‚ SOLID TOP
To be used in combination with 600 or 1600 series.
83,8 mm wide chains available for gap reduction on 85 mm transversal pitch conveyors.
783T SR series have reduced sideflexing radius.
Standard MaterialsProducts Ref. LW DKSolid top 783T
Solid top, SR 783T SR
Pin material: austenitic stainless steel
Dimension mm inches P 25,4 1 B 11,9 .468 M 42,9 1.688 C 61,6 2.425 L 12 .472 H 24,6 .968 E 7,10 .279 RD 130 5.118 GC(straight) 46 1.811 GC (curve) 44,5 1.752
783T (Solid Top - Tab)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW)
LW 783T K 3¼ 82,6 3.25 8,7 0.34 457,2 18.00 1700 382 1,73 1.16
LW 783T K 83,8 83,8 3.30 8,7 0.34 457,2 18.00 1700 382 1,76 1.18
LW 783T K 4½ 114,3 4.50 8,7 0.34 609,6 24.00 1700 382 1,99 1.33
REGINA DK
DK 783T K 3¼ 82,6 3.25 8,7 0.34 457,2 18.00 1700 382 1,73 1.16
DK 783T K 83,8 83,8 3.30 8,7 0.34 457,2 18.00 1700 382 1,69 1.18
DK 783T K 4½ 114,3 4.50 8,7 0.34 609,6 24.00 1700 382 1,69 1.33
Standard length: 3,048 m (10 feet)
783T SR (Solid Top - Tab - Reduced sideflexing Radius)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) LW 783T SR K 3¼ 82,6 3.25 8,7 0.34 298,5 11.75 1700 382 1,73 1.16
REGINA DK DK 783T SR K 3¼ 82,6 3.25 8,7 0.34 298,5 11.75 1700 382 1,73 1.16
Standard length: 3,048 m (10 feet)
Corner trackssee page 280
Sprockets see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
Sprockets see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
SIDEFLEXING TAB CHAINS
783T SR (Solid Top - Tab - Reduced sideflexing Radius)NEW
125
782M AND 783M SERIES - 1” PITCH‚ FLUSH GRID AND SOLID TOP
782M series can be used in combination with 1500 series. 783M series can be used in combination with 600 and 1600 series.
83,8 mm wide chains for gap reduction on 85 mm transversal pitch conveyors. Particularly suitable for inliners.
Standard MaterialsProducts Ref. LW DKFlush grid 782M
Solid top 783M
Pin material: magnetic stainless steel
Dimension mm inches P 25,4 1 M 42 1.654 L 12 .472 H 21 .827 E 8 .315 RD 120 4.724 GC(straight) 44 1.732 GC (curve) 44 1.732
782M (Flush grid - Magnetic)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) LW 782M K 83,8 83,8 3.30 8,7 0.34 500 19.68 1700 382 1,69 1.13
REGINA DK DK 782M K 83,8 83,8 3.30 8,7 0.34 500 19.68 1700 382 1,69 1.13
Standard length: 3,048 m (10 feet)
Dimension mm inches P 25,4 1 M 42 1.654 L 12 .472 H 21 .827 E 8 .315 RD 120 4.724 GC(straight) 44 1.732 GC (curve) 44 1.732
783M (Solid Top - Magnetic)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) LW 783M K 83,8 83,8 3.30 8,7 0.34 500 19.68 1700 382 1,82 1.22
REGINA DK DK 783M K 83,8 83,8 3.30 8,7 0.34 500 19.68 1700 382 1,82 1.22
Standard length: 3,048 m (10 feet)
Corner trackssee page 241
Sprockets and Idlerwheels see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
SIDEFLEXING MAGNETIC CHAINS
Corner trackssee page 241
Sprockets and Idlerwheels see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
126
1600 SERIES - 1”PITCH, SOLID TOP
1600GATM can be used in combination with 1600 Modular belts.Active transfer modules 1600GATM allow the transfer of products between two 90° conveyor tracks without using dead plates.The special wing shaped module profile supports the products dynamically during transfer on the take-away belt.Available left and right version.
Standard MaterialsProducts Ref. LW DK *PPSolid top with guide 1600GATM
Pin material: PP - Polypropylene
Dimension mm inches A 6,7 .264 B 4,9 .193 C 21,3 .839 D 25,4 1 E 4,6 .181 G 42 1.654 L 4,35 .171 P 25,4 1 RD 20 .787 GC 44 1.732
1600GATM (Solid top - Right Version)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW)1600BGATM LW 0085 DX 110 4.33 8,7 0.34 1840 415 0,84 0.56
1600BGATM LW 0170 DX 195 7.68 8,7 0.34 3670 825 1,51 1.01
REGINA DK1600BGATM DK 0085 DX 110 4.33 8,7 0.34 1840 415 0,84 0.56
1600BGATM DK 0170 DX 195 7.68 8,7 0.34 3670 825 1,51 1.51
Standard length: 3,048 m (10 feet)
1600GATM (Solid top - Left Version)
Sprockets and Idlerwheels see pages 224÷227
Chain materialsee page 13
Sprocket positioningsee pages 305-307
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) 1600BGATM LW 0085 SX 110 4.33 8,7 0.34 1840 415 0,84 0.56
REGINA DK 1600BGATM DK 0085 SX 110 4.33 8,7 0.34 1840 415 0,84 0.56
*Due to different shrinkage of materials, actual width is larger than the standard. Standard length: 3,048 m (10 feet)
onrequest
1600 SERIESNEW
ACTIVE TRANSFER MODULES
Right Version Left Version
Sprockets and Idlerwheels see pages 224÷227
Chain materialsee page 13
Sprocket positioningsee pages 305-307
127
1500 SERIES - 1” PITCH, FLUSH GRID
1500GATM can be used in combination with 1500 Modular belts series.Active transfer modules 1500GATM allow the transfer of products between two 90° conveyor tracks without using dead plates.The special wing shaped module profile supports the products dynamically during transfer on the take-away belt.This system is particularly suitable for aluminium cans.
Standard MaterialsProducts Ref. LW DK *PPFlush grid with guide 1500GATM
Pin material: PP - Polypropylene
Dimension mm inches A 6,7 .264 B 4,9 .193 C 21,3 .839 D 25,4 1 E 4,6 .181 G 42 1.654 L 4,35 .171 P 25,4 1 RD 20 .787 GC 44 1.732
1500GATM (Flush grid – Right Version)
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ACETAL RESIN (LW) 1500BGATM LW 0170 DX 195 7.68 8,7 0.34 3670 825 1,21 0.81
REGINA DK 1500BGATM DK 0170 DX 195 7.68 8,7 0.34 3670 825 1,21 0.81
*Due to different shrinkage of materials, actual width is larger than the standard. Standard length: 3,048 m (10 feet)
onrequest
ACTIVE TRANSFER MODULES
Sprockets and Idlerwheels see pages 224÷227
Chain materialsee page 13
Sprocket positioning see pages 305-307
128
NEWRR1600 SERIES - 1” PITCH, LIGHT DUTY, RAISED RIB
Application
- Packaging machines
Installation guidelines
RR 1600 dedicated widths are used in combination with combs for the head transfer of the products.Different widths (30 mm, 38,5 mm, 47 mm and 58 mm), combs and sprockets are available for the maximum flexibility in conveyor lay-out definition.See page 289 for the recommended sprocket/comb matching.
The “Z” rib design offers the maximum support to the conveyed products, even near the module’s edge.
Benefits
DEDICATED WIDHTS
Ideal support for
unstableproducts
Easy assembly and disassembly
Retention clips can easily be moved from the side of the belt for assembling and disassembling.Only a small movement is required, the clip remains in the module.
Reliable drive
The accurate tooth profile with a large cross section ensures high drive capacity and long wear life of sprockets and modules.The central pocket makes these belts bidirectional.
129
RR1600 SERIES - 1” PITCH, RAISED RIB
The ideal ratio rib thickness/spacing offers high support even for the most unstable products, such as PET bottles with petaloid bottom, cans, 3-piece cans.Optimum liquid drainage and good mechanical strength.
Standard MaterialsProducts Ref. UP *PPRaised Rib RR1600
Pin material: PBT
Dimension mm inches E 4,6 .181 H 14,3 .562 L 4,35 .171 P 25,4 1 RD 240 9.448
RR1600 (Raised Rib – 1” Pitch)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP)
RR1600A UP K 30 30 1.17 8,7 0.34 700 162 0,39 0.26
RR1600A UP K 38,5 38,5 1.50 8,7 0.34 950 219 0,50 0.36
RR1600A UP K 47 47 1.83 8,7 0.34 1150 265 0,60 0.40
RR1600A UP K 58 58 2.26 8,7 0.34 1400 323 0,75 0.50
POLYPROPYLENE* (PP)
RR1600A PP K 30 30 1.17 8,7 0.34 315 73 0,27 0.18
RR1600A PP K 38,5 38,5 1.50 8,7 0.34 415 96 0,33 0.22
RR1600A PP K 47 47 1.83 8,7 0.34 500 115 0,40 0.27
RR1600A PP K 58 58 2.26 8,7 0.34 650 150 0,49 0.33
*Due to different shrinkage of materials, actual width is larger than the standard. Standard length: 3,048 m (10 feet)
Sprockets see pages 224÷227
Chain materialsee page 13
Sprocket positioningsee pages 305÷306
Combs seepages 288
RR1600 SERIESNEW
DEDICATED WIDTHS
132
American standard
These belts are ideal for depalletizing, palletizing and mass flow conveying in food, beverage and packaging applications.Due to their high mechanical strength and large sliding area they also offer the best performance in applications with high product loads and a long center to center distance.
High mechanical strength
The high mechanical strength and transversalstiffness of these belts make them suitable forthe most critical applications (high product loads and long center to center distance).
Reliable drive
The accurate tooth profile with high cross section ensures high drive capacity and long wear life of sprockets and modules. The central pocket makes these belts bidirectional.
Easy assembly and disassembly
Retention clips can easily be moved from theside of the belt for assembling and disassembling.The clip remains located in the module.
1110, 1210 AND 1310 SERIES - 1” PITCH, LIGHT DUTY
9mm
MODULAR PLASTIC BELTS
Features and Benefits
133
1110 SERIES - 1” PITCH, RAISED RIB
This belt allows the head transfer of the products by usingtransfer combs and has a open area to permit liquid drainage and belt cleaning.Particularly suitable for product infeed of packaging machines.
Standard MaterialsProducts Ref. LW *PPRaised rib 1110
Belt widths: 152,4 mm (6’’) or wider in 76,2 mm (3”) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 21580 N/m (1,480 lb/ft) (for LW material) 10920 N/m (748 lb/ft) (for PP material) - Open Surface: 30%
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW)BELT
WEIGHT
POLYPROPYLENE* PPBELT
WEIGHTREGINA REF. REGINA REF.
mm inches kg/m lbs/ft kg/m lbs/ft
152,4 6 1110 LW 006 1,33 0.89 1110 PP 006 0,90 0.60
228,6 9 1110 LW 009 2,00 1.34 1110 PP 009 1,35 0.91
304,8 12 1110 LW 012 2,65 1.78 1110 PP 012 1,78 1.20
381,0 15 1110 LW 015 3,30 2.22 1110 PP 015 2,22 1.49
457,2 18 1110 LW 018 3,95 2.65 1110 PP 018 2,66 1.79
533,4 21 1110 LW 021 4,61 3.10 1110 PP 021 3,10 2.08
609,6 24 1110 LW 024 5,26 3.54 1110 PP 024 3,54 2.38
685,8 27 1110 LW 027 5,91 3.97 1110 PP 027 3,98 2.68
762,0 30 1110 LW 030 6,57 4.42 1110 PP 030 4,42 2.97
838,2 33 1110 LW 033 7,22 4.85 1110 PP 033 4,86 3.27
914,4 36 1110 LW 036 7,87 5.29 1110 PP 036 5,30 3.56
990,6 39 1110 LW 039 8,53 5.73 1110 PP 039 5,74 3.86
1066,8 42 1110 LW 042 9,18 6.17 1110 PP 042 6,17 4.15
1143,0 45 1110 LW 045 9,83 6.61 1110 PP 045 6,61 4.44
1219,2 48 1110 LW 048 10,50 7.06 1110 PP 048 7,06 4.75
1295,4 51 1110 LW 051 11,14 7.49 1110 PP 051 7,49 5.03
1371,6 54 1110 LW 054 11,79 7.92 1110 PP 054 7,93 5.33
1447,8 57 1110 LW 057 12,45 8.37 1110 PP 057 8,37 5.63
1524,0 60 1110 LW 060 13,10 8.80 1110 PP 060 8,81 5.92
Belts wider than 1524mm (60”) available, with increments of 76,2mm (3”).Example: 60 + 3 = 63 inches Ref. (in LW material) 1110 LW 063.*Due to different shrinkage of materials, actual width is larger than the standard.
Belts available in the requested length.
Dimension mm inches E 5,4 .212 H 15 .591 L 4,8 .189 P 25,4 1 RD 80 3.15 T 9,6 .378
Sprockets see pages 224÷227
Belt materialsee page 13
Sprocket positioning see page 309
Combs see pages 2901110 (Raised Rib – 1”Pitch)
MODULAR BELTS
134
This belt has an open surface area to permit drainage ofliquid, sanitation and cooling or warming of products.Particularly suitable for conveying aluminium cans.
Standard MaterialsProducts Ref. LW *PP DKFlush grid 1210
Belt widths: 152,4 mm (6’’) or wider in 76,2 mm (3”) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 21580 N/m (1,480 lb/ft) (for LW material) 10920 N/m (748 lb/ft) (for PP material) - Open Surface: 30%
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW)BELT
WEIGHT
POLYPROPYLENE* PPBELT
WEIGHTREGINA REF. REGINA REF.
mm inches kg/m lbs/ft kg/m lbs/ft
152,4 6 1210 LW 006 1,06 0.71 1210 PP 006 0,72 0.48
228,6 9 1210 LW 009 1,58 1.06 1210 PP 009 1,07 0.72
304,8 12 1210 LW 012 2,10 1.41 1210 PP 012 1,42 0.95
381,0 15 1210 LW 015 2,62 1.76 1210 PP 015 1,77 1.19
457,2 18 1210 LW 018 3,14 2.11 1210 PP 018 2,12 1.42
533,4 21 1210 LW 021 3,65 2.45 1210 PP 021 2,46 1.65
609,6 24 1210 LW 024 4,17 2.80 1210 PP 024 2,81 1.89
685,8 27 1210 LW 027 4,69 3.15 1210 PP 027 3,16 2.12
762,0 30 1210 LW 030 5,31 3.57 1210 PP 030 3,51 2.36
838,2 33 1210 LW 033 5,72 3.84 1210 PP 033 3,86 2.59
914,4 36 1210 LW 036 6,24 4.19 1210 PP 036 4,21 2.83
990,6 39 1210 LW 039 6,76 4.54 1210 PP 039 4,55 3.06
1066,8 42 1210 LW 042 7,28 4.89 1210 PP 042 4,90 3.29
1143,0 45 1210 LW 045 7,80 5.24 1210 PP 045 5,25 3.53
1219,2 48 1210 LW 048 8,32 5.59 1210 PP 048 5,61 3.77
1295,4 51 1210 LW 051 8,83 5.93 1210 PP 051 5,95 4.00
1371,6 54 1210 LW 054 9,35 6.28 1210 PP 054 6,30 4.23
1447,8 57 1210 LW 057 9,87 6.63 1210 PP 057 6,64 4.46
1524,0 60 1210 LW 060 10,38 6.98 1210 PP 060 7,00 4.70
Belts wider than 1524 mm (60”) available, with increments of 76,2 mm (3”).Example: 60 + 3 = 63 inches Ref. (in LW material) 1210 LW 063.*Due to different shrinkage of materials, actual width is larger than the standard.
Belts available in the requested length.
Dimension mm inches E 5,4 .212 L 4,8 .189 P 25,4 1 RD 20 .787 T 9,6 .378
Sprockets see pages 224÷227
Belt materialsee page 13
Sprocket positioning see page 309
onrequest
1210 SERIES - 1” PITCH, FLUSH GRID
1210 (Flush Grid – 1”Pitch)
MODULAR BELTS
135
1310 SERIES - 1” PITCH, SOLID TOP
This belt offers a smooth surface to provide excellent support and minimize product tippage.It is particularly suitable for small sized products and unstable containers (for example PET bottles with petaloid bottom, glass bottles and products of small diameter).
Standard MaterialsProducts Ref. LW *PP DK *ASSolid Top 1310
Belt widths: 152,4 mm (6’’) or wider in 76,2 mm (3”) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 21580 N/m (1.480 lb/ft) (for LW material) 10920 N/m (748 lb/ft) (for PP material)
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (LW)BELT
WEIGHT
POLYPROPYLENE* PPBELT
WEIGHTREGINA REF. REGINA REF.
mm inches kg/m lbs/ft kg/m lbs/ft
152,4 6 1310 LW 006 1,18 0.79 1310 PP 006 0,80 0.54
228,6 9 1310 LW 009 1,77 1.19 1310 PP 009 1,19 0.80
304,8 12 1310 LW 012 2,35 1.58 1310 PP 012 1,58 1.06
381,0 15 1310 LW 015 2,92 1.96 1310 PP 015 1,97 1.32
457,2 18 1310 LW 018 3,50 2.35 1310 PP 018 2,36 1.59
533,4 21 1310 LW 021 4,08 2.74 1310 PP 021 2,74 1.84
609,6 24 1310 LW 024 4,66 3.13 1310 PP 024 3,13 2.10
685,8 27 1310 LW 027 5,24 3.52 1310 PP 027 3,52 2.37
762,0 30 1310 LW 030 5,82 3.91 1310 PP 030 3,91 2.63
838,2 33 1310 LW 033 6,40 4.30 1310 PP 033 4,30 2.89
914,4 36 1310 LW 036 6,98 4.69 1310 PP 036 4,68 3.15
990,6 39 1310 LW 039 7,55 5.07 1310 PP 039 5,07 3.41
1066,8 42 1310 LW 042 8,13 5.46 1310 PP 042 5,46 3.67
1143,0 45 1310 LW 045 8,71 5.85 1310 PP 045 5,85 3.93
1219,2 48 1310 LW 048 9,30 6.25 1310 PP 048 6,24 4.19
1295,4 51 1310 LW 051 9,87 6.63 1310 PP 051 6,62 4.45
1371,6 54 1310 LW 054 10,45 7.02 1310 PP 054 7,00 4.70
1447,8 57 1310 LW 057 11,03 7.41 1310 PP 057 7,40 4.97
1524,0 60 1310 LW 060 11,60 7.80 1310 PP 060 7,78 5.23
Belts wider than 1524 mm (60”) available, with increments of 76,2 mm (3”).Example: 60 + 3 = 63 inches Ref. (in LW material) 1310 LW 063.*Due to different shrinkage of materials, actual width is larger than the standard.
Belts available in the requested length.
Dimension mm inches E 5,4 .212 L 4,8 .189 P 25,4 1 RD 20 .787 T 9,6 .378
onrequest
1310 (Solid Top – 1”Pitch)
MODULAR BELTS
Sprockets see pages 224÷227
Belt materialsee page 13
Sprocket positioning see page 309
onrequest
138
USPM SERIES - 1” PITCH, HEAVY DUTY
Installation guidelines
Widths and guides are designed for installation on conveyors with 85 mm between parallel tracks and 44 mm clearance between the wear strips.
Features and Benefits
Large bottom sliding surface
The extremely large contact surface reduces the specific pressure with the wear strips and consequently the wear of the belt bottom surface (limited reduction in thickness).
Smooth and uniform surface
The surface near the edge of the modules, which is critical for the side transfer of the product, is uniform, with no discontinuities.The side transfer of the products is not disturbed.
Easy assembly and disassembly
Retention clips can easily be moved from the side of the belt for assembling and disassembling. Only a small movement is required, the clip remains located in the module.
USPM series can be used together with magnetic or tab sideflexing chains 793 series (see page 141). Same thickness of 12,7 mm for easy installation side by side and standardization of wear strips.
Tab chains 793T use the same curves as Flitetop® plastic chains 880T, 879T and Flitetop® steel chains 881T and 981T.(For tab curves see pag. 280)
Magnetic chains 793M have no tab or bevel profile and have been designed to be installed on magnetic curves.(For magnetic curves see pag. 238).
For 90° products transfer, also availability of ATM (Active Transfer Modules) series (see pag. 144)
MODULAR PLASTIC BELTS - METRIC STANDARD
139
USPM SERIES - 1” PITCH, SOLID TOP
The extremely good flatness, manufacturing accuracy, low coefficient of friction, make the side transfer of the products very easy.Completely closed surface, no gap between the modules, even when engaging on the sprockets.Particularly suitable for glass products, small sized products and unstable containers (for example PET bottles with petaloid base).
83,8 mm wide chains for gap reduction on 85 mm transversal pitch conveyors. Particularly suitable for inliners.
Standard MaterialsProducts Ref. UP DKSolid top with guide USPMG
Pin material: PBT
Dimension mm inches A 10 .394 B 6,5 .256 E 6,26 .246 G 42,2 1.661 L 6,35 .25 P 25,4 1 RD 25 .984 GC 44 1.732
USPM (Solid top – 1” Pitch)
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP) USPMG UP K 83,8 83,8 3.30 12,7 0.50 2975 670 1,21 0.81
REGINA DK USPMG DK K 83,8 83,8 3.30 12,7 0.50 2975 670 1,21 0.81
Standard length: 3,048 m (10 feet)
Sprockets and Idlerwheels see pages 229÷231
Chain materialsee page 13
Sprocket positioning see pages 310÷311
DEDICATED WIDTHS
140
USPM SERIES - 1” PITCH, SOLID TOP
Extremely good flatness, manufacturing accuracy and low coefficient of friction make the side transfer of the products very easy.Completely closed surface, no gap between the modules, even when engaging on the sprockets. Particularly suitable for glass products, small sized products and unstable containers (for example PET bottles with petaloid base).
Standard MaterialsProducts Ref. UP DK Solid top USPM Solid top with guide USPMG
Belt widths: 170 mm (6.693’’) or wider in 85 mm increments - Pin material: PBT - Working Load (at 25°C/77°F): 35000 N/m (2,400 lb/ft)
Dimension mm inches A 10 .394 B 6,5 .256 C 63,5 2.5 E 6,26 .246 G 42,2 1.661 L 6,35 .25 P 25,4 1 RD 25 .984 T 12,7 .5 GC 44 .173
BELT NOMINAL
WIDTH “W”
ACETAL RESIN (UP) REGINA DKBELT
WEIGHTREGINA REF. REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 WITHOUT GUIDE WITH GUIDE G WITH GUIDE G1 kg/m lbs/ft
170 6.69 USPM UP 0170 USPMG UP 0170 USPMG1 UP 0170 USPM DK 0170 USPMG DK 0170 USPMG1 DK 0170 2,34 1.57
255 10.04 USPM UP 0255 USPMG UP 0255 USPMG1 UP 0255 USPM DK 0255 USPMG DK 0255 USPMG1 DK 0255 3,49 2.35
340 13.39 USPM UP 0340 USPMG UP 0340 USPMG1 UP 0340 USPM DK 0340 USPMG DK 0340 USPMG1 DK 0340 4,64 3.12
425 16.73 USPM UP 0425 USPMG UP 0425 USPMG1 UP 0425 USPM DK 0425 USPMG DK 0425 USPMG1 DK 0425 5,78 3.88
510 20.08 USPM UP 0510 USPMG UP 0510 USPMG1 UP 0510 USPM DK 0510 USPMG DK 0510 USPMG1 DK 0510 6,92 4.65
595 23.43 USPM UP 0595 USPMG UP 0595 USPMG1 UP 0595 USPM DK 0595 USPMG DK 0595 USPMG1 DK 0595 8,07 5.42
680 26.77 USPM UP 0680 USPMG UP 0680 USPMG1 UP 0680 USPM DK 0680 USPMG DK 0680 USPMG1 DK 0680 9,21 6.19
765 30.12 USPM UP 0765 USPMG UP 0765 USPMG1 UP 0765 USPM DK 0765 USPMG DK 0765 USPMG1 DK 0765 10,36 6.96
850 33.46 USPM UP 0850 USPMG UP 0850 USPMG1 UP 0850 USPM DK 0850 USPMG DK 0850 USPMG1 DK 0850 11,51 7.74
935 36.81 USPM UP 0935 USPMG UP 0935 USPMG1 UP 0935 USPM DK 0935 USPMG DK 0935 USPMG1 DK 0935 12,65 8.50
1020 40.16 USPM UP 1020 USPMG UP 1020 USPMG1 UP 1020 USPM DK 1020 USPMG DK 1020 USPMG1 DK 1020 13,80 9.28
1105 43.50 USPM UP 1105 USPMG UP 1105 USPMG1 UP 1105 USPM DK 1105 USPMG DK 1105 USPMG1 DK 1105 14,94 10.04
1190 46.85 USPM UP 1190 USPMG UP 1190 USPMG1 UP 1190 USPM DK 1190 USPMG DK 1190 USPMG1 DK 1190 16,08 10.81
1275 50.20 USPM UP 1275 USPMG UP 1275 USPMG1 UP 1275 USPM DK 1275 USPMG DK 1275 USPMG1 DK 1275 17,23 11.58
1360 53.54 USPM UP 1360 USPMG UP 1360 USPMG1 UP 1360 USPM DK 1360 USPMG DK 1360 USPMG1 DK 1360 18,37 12.35
1445 56.89 USPM UP 1445 USPMG UP 1445 USPMG1 UP 1445 USPM DK 1445 USPMG DK 1445 USPMG1 DK 1445 19,52 13.12
1530 60.24 USPM UP 1530 USPMG UP 1530 USPMG1 UP 1530 USPM DK 1530 USPMG DK 1530 USPMG1 DK 1530 20,66 13.89
G version
G1 version
Belts wider than 1530 mm available (increments of 85 mm) Example: 1530+85=1615 mm width, without guide Ref. (in DK material) USPM DK 1615.
Standard length for belts up to a width of 680 mm: 3,048 m (10 feet). Wider belts available in any requested length.
Sprockets and Idlerwheels see pages 229÷231
Belt materialsee page 13
Sprocket positioning see pages 310÷311USPM (Solid top - 1” Pitch)
Shoe guide positionModular belt:
MODULAR BELTS
141
793T AND 793M SERIES - 1” PITCH, HEAVY DUTY
Installation guidelines
Matveyor® sideflexing chain 793T and 793M can be used on conveyors side by side with ULTOP® UCC and Matveyor® USP and USPM series.Same thickness of 12,7mm for easy installation side by side and standardization of wear strips.
Tab chains 793T use the same curves as Flitetop® plastic chains 880T, 879T and Flitetop® steel chains 881T and 981T.(for TAB curves see pag. 280)
Magnetic chains 793M have no tab or bevel profile and have been designed to be installed on magnetic curves.(For magnetic curves see pag. 238)
Gentle product handling
The small 1” pitch top-plate combination results in a very low gap between flights. Availability of materials with extremely low friction coefficients (see pag. 13).
Features and Benefits
Standardization in conveyor construction
Easy installation side by side with Matveyor® and Ultop® belts.
SIDEFLEXING CHAINS
reduced gap
142
793T SERIES - 1” PITCH, SOLID TOP
To be used in combination with USPM, USP and UCC series.
83,8 mm wide chains available for gap reduction on 85 mm transversal pitch conveyors. Particularly suitable for inliners.
Standard MaterialsProducts Ref. UP DKSolid top 793T
Pin material: austenitic stainless steel
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP)
UP 793T K 3¼ 82,6 3.25 12,7 0.50 457,2 18 2200 494.5 2,05 1.37
UP 793T K 83,8 83,8 3.30 12,7 0.50 457,2 18 2200 494.5 2,08 1.39
UP 793T K 4½ 114,3 4.50 12,7 0.03 609,6 24 2200 494.5 2,45 1.64
REGINA DK
DK 793T K 3¼ 82,6 3.25 12,7 0.50 457,2 18 2200 494.5 2,05 1.37
DK 793T K 83,8 83,8 3.30 12,7 0.50 457,2 18 2200 494.5 2,08 1.39
DK 793T K 4½ 114,3 4.50 12,7 0.50 609,6 24 2200 494.5 2,45 1.64
Standard length: 3,048 m (10 feet)
793T (Solid Top - Tab)Corner trackssee page 280
Sprockets see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
Dimension mm inches P 25,4 1 B 11,9 .468 M 42,9 1.688 C 61,6 2.425 L 16 .629 H 28,6 1.125 E 7,10 .279 RD 130 5.118 GC(straight) 46 1.811 GC (curve) 44,5 1.752
SIDEFLEXING TAB CHAINS
143
793M SERIES - 1” PITCH, SOLID TOP
To be used in combination with USPM, USP and UCC series.
83,8 mm wide chain available for gap reduction on 85 mm transversal pitch conveyors. Particularly suitable for inliners
Dimension mm inches P 25,4 1 M 42 1.654 L 16 .63 H 25 .984 E 8 .315 RD 130 5.118 GC(straight) 44 1.732 GC (curve) 44 1.732
Standard MaterialsProducts Ref. UP DKSolid top 793M
Pin material: magnetic stainless steel
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
SIDEFLEXING RADIUS R
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP) UP 793M K 83,8 83,8 3.30 12,7 0.50 457,2 18 2200 494.5 2,07 1.39
REGINA DK DK 793M K 83,8 83,8 3.30 12,7 0.50 457,2 18 2200 494.5 2,07 1.39
Standard length: 3,048 m (10 feet)
793M (Solid Top - Magnetic)
Corner trackssee page 241
Sprockets and Idlerwheels see page 228
Chain materialsee page 13
Sprocket positioningsee page 308
SIDEFLEXING MAGNETIC CHAINS
144
USPM SERIES - 1” PITCH, SOLID TOP
To be used in combination with USPM belts series.Active transfer modules USPMGATM series allow the transfer of the products between two 90° conveyor tracks without using dead plates.The special module profile, wing shaped, supports the products dynamicallyduring transfer on the take-away belt. Available left and right version.
USPMGATM (Solid top - Right Version)
USPMGATM (Solid top - Left Version)
Standard MaterialsProducts Ref. UP DKSolid top with guide USPMGATM
Pin material: PBT
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP) USPMGATM UP 0085 DX 127,5 5.02 12,7 0.50 2975 670 1,54 1.03
REGINA DK USPMGATM DK 0085 DX 127,5 5.02 12,7 0.50 2975 670 1,54 1.03
Standard length: 3,048 m (10 feet)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP) USPMGATM UP 0085 SX 127,5 5.02 12,7 0.50 2975 670 1,54 1.03
REGINA DK USPMGATM DK 0085 SX 127,5 5.02 12,7 0.50 2975 670 1,54 1.03
Standard length: 3,048 m (10 feet)
Sprockets and Idlerwheel see pages 229÷231
Chains materialsee page 13
Sprocket positioningsee pages 310-313
ACTIVE TRANSFER MODULES
Right version Left version
USPMGATM (Solid top - Left VersionNEW
Dimension mm inches A 10 .394 B 6,5 .256. C 21,3 .839 D 38,1 1.5 E 6,26 .246 G 42,2 1.661 L 6,35 .25 P 25,4 1 RD 25 .984 GC 44 1.732
Sprockets and Idlerwheel see pages 229÷231
Chains materialsee page 13
Sprocket positioningsee pages 310-313
145
- It is possible to build wide accumulation tables with rollers over the entire width, due to 85 mm width increments
- High ratio outside/inside roller diameter: better rotation capa bility, lower coefficient of friction in combination with low noise.
- Self cleaning roller profile (barrel shaped).
Benefits
LBP USPM SERIES - 1” PITCH, HEAVY DUTY WITH ROLLERS
Applications
Food and beverage industry packaging line (PET bottle packs in heat shrink film).Paper and cardboard boxes.General purpose conveying applications with problems of back-line pressure between products.
LBP Modular Belts are based on USPM series (see page 138). Modules are made by DuPontTM Delrin® special dark grey acetal resin, for good wear resistance and mechanical strength.Rollers made of specifically designed thermoplastic resin.
Features and materials
DuPont™ Delrin® and DuPont™ Kevlar® are registered trade marks of E.I. DuPont De Nemours and Associates
MANCA FOTO
Ø 4 mm
Ø 11 mm austenitic stainless
steel pins
MODULAR PLASTIC BELTS
146
Dimension mm inches A 10 .394 B 6,5 .256 C 63,5 2.5 E 6,26 .246 G 42,2 1.661 H 27,2 1.071 J 11 .433 L 6,35 .25 P 25,4 1 RD 230 9.055 T 12,7 .5 GC 44 1.732
LBP USPM SERIES 1” PITCH, WITH LBP ROLLERS
Standard MaterialsProducts Ref. DGLBP LBP USPM
LBP with guide LBP USPMG1
Belt widths: 85 mm (3.346’’) or wider in 85 mm (3.346’’) increments - Pin material: PBT - Roller material: Low friction and low noise acetal resin - Working Load (at 25°C/77°F): 35000 N/m (2,400 lb/ft)
BELT NOMINAL WIDTH “W”
ACETAL RESIN (DG)BELT WEIGHT
REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE kg/m lbs/ft
85 3.35 LBP USPM DG 0085 LBP USPMG DG 0085 2,73 1.83
170 6.69 LBP USPM DG 0170 LBP USPMG1 DG 0170 5,34 3.59
255 10.04 LBP USPM DG 0255 LBP USPMG1 DG 0255 7,90 5.31
340 13.39 LBP USPM DG 0340 LBP USPMG1 DG 0340 10,56 7.10
425 16.73 LBP USPM DG 0425 LBP USPMG1 DG 0425 13,22 8.89
510 20.08 LBP USPM DG 0510 LBP USPMG1 DG 0510 15,78 10.61
595 23.43 LBP USPM DG 0595 LBP USPMG1 DG 0595 18,38 12.35
680 26.77 LBP USPM DG 0680 LBP USPMG1 DG 0680 20,98 14.10
Belts wider than 680 mm available ( increments of 85 mm ). Standard length for belts up to a width of 425 mm: 1,524 m (60 pitches).Example: 680 + 85 = 765 mm width, without guide Ref. (in DG material) LBP USPM DG 0765 Wider belts available in any requested length.
Suitable for applications where a large accumulating conveyor section is needed.
Shoe guide position Dedicated width:
Modular belt:
with guide
LBP USPM (1” Pitch)
DEDICATED WIDTHS AND MODULAR BELTS
Sprockets and Idlerwheel see pages 229÷231
Belt materialsee page 13
Sprocket positioning see pages 310-312
147
- Available either full rubberized or side indent (to allow a return on straight guides without interferences with rubberized portion).
- Outstanding rubber retention (Patent Pending).
- Excellent and reliable rubber grip.
- Large sliding surface for extended wear life.
- Wide sprocket tooth for reliable drive and extended life.
- The maximum angle of the ramp is a function of type, shapeand material of the product to be conveyed. Please contact Regina Application Engineers for a more detailed evaluation.Temperature and other environmental conditions can influence maximum value of the incline.
Benefits
HF USPM SERIES - 1” PITCH, HEAVY DUTY WITH RUBBER SURFACE
Applications
Packaging lines (cardboard, shrink packs).Paper and cardboard boxes.General conveying on inclined conveyors.
HF Modular Belts are based on USPM series (see pag. 138). Modules are available in:• UP - DuPont™ Delrin® special acetal resin.High friction surface is thermoplastic rubber (see table below).
On request it is possible to provide belts rubberized on steps (even) or in accordance with the design of the customer.
Features and materials
DuPont™ Delrin® and DuPont™ Kevlar® are registered trade marks of E.I. DuPont De Nemours and Associates
RUBBERMATERIAL
COLOUR AVERAGE HARDNESS NON SUITABLE WITH RESISTANT TO
THERMOPLASTIC GREEN 80 ShA STRONG ACIDS AND BASES OILS
MODULAR PLASTIC BELTS
148
HF USPM SERIES 1” PITCH, RUBBER SURFACE, FULL COVER
Dimension mm inches A 10 .394 B 6,5 .256 C 63,5 2.5 E 6,26 .246 G 42,2 1.661 L 6,35 .25 P 25,4 1 RD 25 .984 S 3 .118 T 12,7 .5 GC 44 1.732
Standard MaterialsProducts Ref. UPFull Cover HF USPM
Full Cover with Guide HF USPMG1
Belt widths: 170 mm (6.69’’) or wider in 85 mm (3.35’’) increments- Pin material: PBT- Rubber material: Thermoplastic- Rubber hardness: 80 ShA (see page 147)- Working Load (at 25°C/77°F): 35000 N/m (2,400 lb/ft)
BELT NOMINAL WIDTH “W”
ACETAL RESIN (UP)BELT WEIGHT
REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE kg/m lbs/ft
85 3.35 HF USPM UP 0085 HF USPMG UP 0085 1,33 0.89
170 6.69 HF USPM UP 0170 HF USPMG1 UP 0170 2,67 1.79
255 10.04 HF USPM UP 0255 HF USPMG1 UP 0255 3,93 2.64
340 13.39 HF USPM UP 0340 HF USPMG1 UP 0340 5,23 3.52
425 16.73 HF USPM UP 0425 HF USPMG1 UP 0425 6,53 4.39
510 20.08 HF USPM UP 0510 HF USPMG1 UP 0510 7,83 5.26
595 23.43 HF USPM UP 0595 HF USPMG1 UP 0595 9,13 6.14
680 26.77 HF USPM UP 0680 HF USPMG1 UP 0680 10,43 7.00
765 30.12 HF USPM UP 0765 HF USPMG1 UP 0765 11,73 7.88
850 33.46 HF USPM UP 0850 HF USPMG1 UP 0850 13,02 8.75
Belts wider than 850 mm available (increments of 85 mm). Standard length for belts up to a width of 425 mm: 1,524 m (60 pitches).Example: 850 + 85 = 935 mm width, without guide Ref. (in UP material) HF USPM UP 0935 Wider belts available in any requested length.
HF USPM belts are a ideal solution for heavy duty inclines, declines and package handling (acceleration, deceleration, rotation).
Shoe guide positionDedicated width:
with guide
HF USPM SERIES1” PITCH,
NEW
HF USPM (Full cover – 1” Pitch)
NEW
DEDICATED WIDTHS AND MODULAR BELTS
Sprockets and Idlerwheel see pages 229÷231
Belt materialsee page 13
Sprocket positioningsee pages 310÷311
Modular belt:
149
Shoe guide positionModular belt:
with guide
Standard MaterialsProducts Ref. UPSide Indent HFS USPM
Side Indent with Guide HFS USPMG1
Belt widths: 255 mm (10.04’’) or wider in 85 mm (3.35’’) increments- Pin material: PBT- Rubber material: Thermoplastic- Rubber hardness: 80 ShA (see page 147)- Working Load (at 25°C/77°F): 35000 N/m (2,400 lb/ft)
Dimension mm inches A 10 .394 B 6,5 .256 C 63,5 2.5 E 6,26 .246 G 42,2 1.661 L 6,35 .25 P 25,4 1 RD 25 .984 S 3 .118 T 12,7 .5 GC 44 1.732 Z 43,9 1.728
BELT NOMINAL WIDTH “W”
ACETAL RESIN (UP)BELT WEIGHT
REGINA REF.
mm inches WITHOUT GUIDE WITH GUIDE kg/m lbs/ft
255 10.04 HFS USPM UP 0255 HFS USPMG1 UP 0255 2,73 1.83
340 13.39 HFS USPM UP 0340 HFS USPMG1 UP 0340 3,68 2.47
425 16.73 HFS USPM UP 0425 HFS USPMG1 UP 0425 4,63 3.11
510 20.08 HFS USPM UP 0510 HFS USPMG1 UP 0510 5,58 3.75
595 23.43 HFS USPM UP 0595 HFS USPMG1 UP 0595 6,53 4.39
680 26.77 HFS USPM UP 0680 HFS USPMG1 UP 0680 7,48 5.03
765 30.12 HFS USPM UP 0765 HFS USPMG1 UP 0765 8,43 5.67
850 33.46 HFS USPM UP 0850 HFS USPMG1 UP 0850 9,38 6.30
Belts wider than 850 mm available (increments of 85 mm). Standard length for belts up to a width of 425 mm: 1,524 m (60 pitches).Example: 850 + 85 = 935 mm width, without guide Ref. (in UP material) HFS USPM UP 0935 Wider belts available in any requested length.
HFS USPM (Side indent – 1” Pitch)
HFS USPM SERIES1” PITCH, RUBBER SURFACE, SIDE INDENT HFS USPM SERIES1” PITCH,
NEW
MODULAR BELTS
Sprockets and Idlerwheel see pages 229÷231
Belt materialsee page 13
Sprocket positioningsee pages 310÷311
152
USP SERIES - 1” PITCH, HEAVY DUTY
Installation guidelines
Widths according to American standards. Dedicated widths: 3 ¼”, 4 ½”, 7 ½”.Brick laid modular belts in 1” increments.
Features and Benefits
Large bottom sliding surface
The extremely large contact surface reduces the specific pres-sure with the wear strips and consequently the wear of the bottom surface of the belt (limited reduction in thickness).
Smooth and uniform surface
The surface near the edge of the modules which is critical for the side transfer of the products is uniform with no discontinuities.The side transfer of the products is not disturbed.
Easy assembly and disassembly
Retention clips can easily be moved from the side of the belt for assembling and disassembling. Only a small movement is required, the clip remains located in the module.
USP series can be used together with magnetic or tab sideflexing chains 793 series (see pag. 141). Same thickness of 12,7mm for easy installation side by side and standardization of wear strips.
For 90° products transfer, also availability of ATM (Active Transfer Modules) series (see pages 155÷157).
MODULAR PLASTIC BELTS, AMERICAN STANDARD
153
Dimension mm inches A 10 .394 B 6,5 .256 E 6,26 .246 G 43 1.693 L 6,35 .25 P 25,4 1 RD 25 .984 GC 44.5 1.751
Shoe guide position Dedicated width:
USP SERIES - 1” PITCH, SOLID TOP
Completely closed surface, no gap between the modules, even when engaging on the sprockets.Particularly suitable for glass products.
USP (Solid top – 1” Pitch)
Standard MaterialsProducts Ref. UP DKSolid top USP
Solid top with guide USPG
Pin material: PBT
MATERIALREGINA REF.
WITHOUT GUIDEREGINA REF. WITH GUIDE
CHAIN WIDTH W
PLATE THICKNESST
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCEACETAL RESIN (UP)
USP UP 325 USPG UP 325 82,6 3.25 12,7 0.50 2500 562 1,24 0.83
USP UP 450 USPG UP 450 114,3 4.50 12,7 0.50 3430 770 1,71 1.15
USP UP 750 USPG UP 750 190,5 7.50 12,7 0.50 5710 1,280 2,73 1.83
REGINA DK
USP DK 325 USPG DK 325 82,6 3.25 12,7 0.50 2500 562 1,24 0.83
USP DK 450 USPG DK 450 114,3 4.50 12,7 0.50 3430 770 1,71 1.15
USP DK 750 USPG DK 750 190,5 7.50 12,7 0.50 5710 1,280 2,73 1.83
Standard length: 3,048 m (10 feet)
DEDICATED WIDTHS
Sprockets and Idlerwheel see pages 229÷231
Chain materialsee page 13
Sprocket positioning see pages 314-316
154
USP SERIES - 1” PITCH, SOLID TOP
Completely closed surface, no gap between the modules, even when engaging on the sprockets. Particularly suitable for glass products.
Standard MaterialsProducts Ref. UP DK Solid top USP
Belt widths: 152,4 mm (6’’) or wider in 76,2 mm (3”) standard increments- Pin material: PBT- Working Load (at 25°C/77°F): 30000 N/m (2,055 lb/ft)
Dimension mm inches E 6,26 .246 L 6,35 .25 P 25,4 1 RD 25 .984 T 12,7 .5 GC 44 .173
BELT NOMINAL WIDTH “W”
ACETAL RESIN (UP) REGINA DKBELT WEIGHT
REGINA REF. REGINA REF.
mm inches kg/m lbs/ft
152,4 6 USP UP 006 USP DK 006 2,15 1.45
228,6 9 USP UP 009 USP DK 009 3,18 2.14
304,8 12 USP UP 012 USP DK 012 4,24 2.85
381,0 15 USP UP 015 USP DK 015 5,27 3.54
457,2 18 USP UP 018 USP DK 018 6,37 4.28
533,4 21 USP UP 021 USP DK 021 7,43 4.99
609,6 24 USP UP 024 USP DK 024 8,41 5.65
685,8 27 USP UP 027 USP DK 027 9,56 6.43
762,0 30 USP UP 030 USP DK 030 10,62 7.14
838,2 33 USP UP 033 USP DK 033 11,68 7.85
914,4 36 USP UP 036 USP DK 036 12,75 8.57
990,6 39 USP UP 039 USP DK 039 13,81 9.28
1066,8 42 USP UP 042 USP DK 042 14,87 9.99
1143,0 45 USP UP 045 USP DK 045 15,93 10.71
1219,2 48 USP UP 048 USP DK 048 17,00 11.43
1295,4 51 USP UP 051 USP DK 051 18,06 12.14
1371,6 54 USP UP 054 USP DK 054 19,12 12.85
1447,8 57 USP UP 057 USP DK 057 20,18 13.56
1524,0 60 USP UP 060 USP DK 060 21,25 14.28
Belts wider than 1524mm (60”) available, with standard increments of 76,2mm (3”). Example: 60+3=63 inches Ref. (in UP material) USP UP 063.Also available on request increments of 25,4mm (1”). Example: 48+1=49 inches Ref. (in UP material): USP UP 049.
Belts available in the requested length.
USP (Solid top – 1” Pitch)
MODULAR BELTS
Sprockets see pages 229÷231
Belt materialsee page 13
Sprocket positioningsee pages 314-316
NEW
155
Right version Left version
Dimension mm inches A 10 .394 B 6,5 .256 C(K4½“) 35,5 1.398 C(K7½“) 73,6 2.898 D 38,1 1.5 E 6,26 .246 G 43 1.693 L 6,35 .25 P 25,4 1 RD 25 .984 GC 46 1.811
USP SERIES - 1” PITCH, SOLID TOP
To be used in combination with USP belts series.Active transfer modules USPGATM series allow the transfer of the products between two 90° conveyor tracks without using dead plates. The special modu-le profile, wing shaped, supports the products dynamicallyduring transfer on the take-away belt.Available left and right version.
USPGATM (Solid top - Left Version)
USPGATM (Solid top - Right Version)
Standard MaterialsProducts Ref. UP DKSolid top with guide USPGATM
Pin material: PBT
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP)
USPGATM UP 450 SX 152,4 6 12,7 0.50 3480 780 1,93 1.30
USPGATM UP 750 SX 228,6 9 12,7 0.50 5715 1,280 2,97 1.99
REGINA DKUSPGATM DK 450 SX 152,4 6 12,7 0.50 3480 780 1,93 1.30
USPGATM DK 750 SX 228,6 9 12,7 0.50 5715 1,280 2,97 1.99
Standard length: 3,048 m (10 feet)
MATERIAL REGINA REF.
CHAIN WIDTHW
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAINWEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULTRA PERFORMANCE ACETAL RESIN (UP)
USPGATM UP 450 DX 152,4 6 12,7 0.50 3480 780 1,93 1.30
USPGATM UP 750 DX 228,6 9 12,7 0.50 5715 1,280 2,97 1.99
REGINA DKUSPGATM DK 450 DX 152,4 6 12,7 0.50 3480 780 1,93 1.30
USPGATM DK 750 DX 228,6 9 12,7 0.50 5715 1,280 2,97 1.99
Standard length: 3,048 m (10 feet)
USPGATM (Solid top - Right VersionNEW
ACTIVE TRANSFER MODULES
Sprockets and Idlerwheel see pages 229÷231
Chain materialsee page 13
Sprocket positioningsee pages 315-317
Sprockets and Idlerwheel see pages 229÷231
Chain materialsee page 13
Sprocket positioningsee pages 315-317
156
USP SERIES - 1” PITCH, SOLID TOP
Dimension mm inches A 10 .394 B 6,5 .256 C 35,5 1.398 D 38,1 1.5 E 6,26 .246 G 43 1.693 L 6,35 .25 P 25,4 1 RD 25 .984 T 12,7 .5 GC 46 1.811
Standard MaterialsProducts Ref. UP DKSolid top with guide USPGATM
Belt widths: total width (with wing) 12” (304.8 mm) or wider in 3” (76,2 mm) increments- Pin material: PBT- Working Load (at 25°C/77°F): 30000 N/m (2,055 lb/ft)
BELT NOMINAL WIDTH “W”
ACETAL RESIN (UP) REGINA DKBELT WEIGHT
REGINA REF. REGINA REF.
mm inches kg/m lbs/ft
304,8 12 USPGATM UP 010M SX USPGATM DK 010M SX 4,01 2.70
381,0 15 USPGATM UP 013M SX USPGATM DK 013M SX 5,08 3.41
457,2 18 USPGATM UP 016M SX USPGATM DK 016M SX 6,14 4.13
533,4 21 USPGATM UP 019M SX USPGATM DK 019M SX 7,20 4.84
609,6 24 USPGATM UP 022M SX USPGATM DK 022M SX 8,27 5.56
685,8 27 USPGATM UP 025M SX USPGATM DK 025M SX 9,33 6.27
On request, belts wider than 685,8 mm (27”) available, with standard increments of 76,2 mm (3”). Example: 27+3=30 inches Ref. (in DK material): USPGATM DK 028M SX
Wider belts available in any requested length.
USPGATM (Modular belts - Left Version)
ACTIVE TRANSFER MODULESMODULAR BELTS LEFT VERSION
NEW
Sprockets and Idlerwheel see pages 229÷231
Belt materialsee page 13
Sprocket positioningsee pages 315-317
157
USP SERIES - 1” PITCH, SOLID TOP
Dimension mm inches A 10 .394 B 6,5 .256 C 35,5 1.398 D 38,1 1.5 G 43 1.693 L 6,35 .25 P 25,4 1 RD 25 .984 T 12,7 .5 GC 46 1.811
BELT NOMINAL WIDTH “W”
ACETAL RESIN (UP) REGINA DKBELT WEIGHT
REGINA REF. REGINA REF.
mm inches kg/m lbs/ft
304,8 12 USPGATM UP 010M DX USPGATM DK 010M DX 4,01 2.70
381,0 15 USPGATM UP 013M DX USPGATM DK 013M DX 5,08 3.41
457,2 18 USPGATM UP 016M DX USPGATM DK 016M DX 6,14 4.13
533,4 21 USPGATM UP 019M DX USPGATM DK 019M DX 7,20 4.84
609,6 24 USPGATM UP 022M DX USPGATM DK 022M DX 8,27 5.56
685,8 27 USPGATM UP 025M DX USPGATM DK 025M DX 9,33 6.27
On request, belts wider than 685,8 mm (27”) available, with standard increments of 76,2 mm (3”). Example: 27+3=30 inches Ref. (in DK material): USPGATM DK 028M DX
Wider belts available in any requested length.
USPGATM (Modular belts - Right Version)
Standard MaterialsProducts Ref. UP DKSolid top with guide USPGATM
Belt widths: total width (with wing) 12” (304.8 mm) or wider in 3” (76,2 mm) increments- Pin material: PBT- Working Load (at 25°C/77°F): 30000 N/m (2,055 lb/ft)
USP NEW
ACTIVE TRANSFER MODULESMODULAR BELTS RIGHT VERSION
Sprockets and Idlerwheel see pages 229÷231
Belt materialsee page 13
Sprocket positioningsee pages 315-317
158
793T SERIES - 1” PITCH, HEAVY DUTY
Installation guidelines
Matveyor® sideflexing chain 793T can be used on conveyors side by side with ULTOP® UCC and Matveyor® USP and USPM series.Same thickness of 12,7mm for easy installation side by side and standardization of wear strips.
For 793T series see page 142.
Tab chains 793T use the same curves as Flitetop® plastic chains 880T, 879T and Flitetop® steel chains 881T and 981T.(for TAB curves see pag. 280)
Gentle product handling
The small 1” pitch-top plate combination results in a very low gap between flights. Availability of materials with extremely low friction coefficients (see pag. 13).
Features and Benefits
Standardization in conveyor construction
Easy installation side by side with Matveyor® and Ultop® belts.
SIDEFLEXING CHAINS
reduced gap
159
UCC SERIES - 1 ½” PITCH, HEAVY DUTY
Installation guidelines
Chain widths according to American standard sizes. Dedicated widths 3 ¼”, 4 ½”, 6”, 7 ½”, 12, 15”, 18” and 24”.Active transfer modules for 90° transfer without dead plates.
Smooth and uniform surface, special edge profiles
The surface near the edge of the modules is uniform with no discontinuities. Thus, the side transfer of the products is not disturbed. The special edge profile is designed for smooth transfer of products, even when the two side by side belts may have a different thickness due to normal wear.
Availability of active transfer modules
Elimination of dead plates at 90° corners, thanks to the wing shaped ATM modules (see pag. 161).A tippage-free transfer with self clearing corners is feasible because products are actively transferred from the ATM mod-ules to the take-away conveyors.
Easy assembly and disassembly
Snapsert™ snaps into place to secure pins. Allows quick as-sembly/disassembly from either side and the reuse of pins.
Reliability in heavy duty application
Completely closed surface, no gap between the flights even when engaging the sprocket.Equipped by stainless steel pins, recommended for heavy duty application because of their superior mechanical characteris-tics. Heavy duty sprocket teeth.
Features and Benefits
UCC GATM chain
TAKE-AWAY chain
DEDICATED WIDTHS, AMERICAN STANDARD
160
UCC SERIES - 1 ½” PITCH, SOLID TOP
Stainless steel pins for ideal performance in heavy duty applications.A complete range of dedicated width chains. Completely closed surface, no gap between the modules, even when engaging the sprockets.Particularly suitable for glass bottles lines and glass manufacturing.
Standard MaterialsProducts Ref. DK ULF Solid top UCCSS
Pin material: austenitic stainless steel
Dimension mm inches E 6,26 .246 L 6,35 .25 P 38,1 1.5 RD 40 1.575
UCC (Solid top – 1 ½” Pitch)
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
REGINA DK
DK UCC 325 SS 82,6 3.2 12,7 0.50 2505 563 1,37 0.92
DK UCC 450 SS 114,3 4.5 12,7 0.50 3469 780 1,84 1.24
DK UCC 600 SS 152,4 6.0 12,7 0.50 4625 1,039 2,5 1.68
DK UCC 750 SS 190,5 7.5 12,7 0.50 5781 1,299 3,02 2.03
DK UCC 1200 SS 304,8 12.0 12,7 0.50 9270 2,083 4,88 3.28
DK UCC 1500 SS 381,0 15.0 12,7 0.50 11590 2,604 6,04 4.06
DK UCC 1800 SS 457,2 18.0 12,7 0.50 13900 3,123 7,26 4.88
DK UCC 2400 SS 609,6 24.0 12,7 0.50 18540 4,165 9,72 6.53
Standard length: 3,048 m (10 feet)
Sprockets see page 232
Chain materialsee page 13
Sprocket positioning see pages 318÷319
DEDICATED WIDTHS
onrequest
161
UCC SERIES - 1 ½” PITCH, SOLID TOP
Active transfer modules UCCGATM allow transfer of products between two 90° conveyor tracks without using dead plates. The special wing shaped module profile supports the products dynamically during transfer on the take-away belt.
Standard MaterialsProducts Ref. DK ULFSolid top UCCGATMSS
Pin material: austenitic stainless steel
Dimension mm inches A 19 .748 B 5,9 .232 C(450) 71,4 2.811 C(750) 139,5 5.492 D 50,8 2 E 6,26 .246 L 6,35 .25 P 38,1 1.5 RD 40 .787
UCCGATM (Solid top - 1 ½” Pitch)
MATERIAL REGINA REF.
CHAIN WIDTH W
PLATE THICKNESS T
WORKING LOAD (25°C/77°F)
CHAIN WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
REGINA DK DK UCC 450GATM SS 165,1 6.5 12,7 0.50 3469 780 2,21 1.49
DK UCC 750GATM SS 241,3 9.5 12,7 0.50 5781 1,299 3,42 2.30
Standard length: 3,048 m (10 feet)
ACTIVE TRANSFER MODULES
onrequest
Sprockets see page 232
Chain materialsee page 13
Sprocket positioning see pages 318-320
162
UCC138 SERIES - ¾” PITCH, SOLID TOP
Optimum support of the conveyed products, no risk for flight detachment (compared to two piece chains).No gap between the flights even when engaging the sprockets.Particularly suitable for packaging machines applications.
Standard MaterialsProducts Ref. ULFSolid top UCC138SS
Pin material: austenitic stainless steel
Dimension mm inches E 4,76 .187 L 6,35 .25 P 19,05 .750 RD 20 .787
UCC138 (Solid top - ¾” Pitch)
MATERIAL REGINA REF. CHAIN WIDTH
WPLATE THICKNESS
HWORKING LOAD
(25°C/77°F) CHAIN
WEIGHT
mm inches mm inches N lbs kg/m lbs/ft
ULF UCC 138 SS 34,9 1.4 15,0 0.59 1225 275 0,68 0.46
Standard length: 3,048 m (10 feet)
Sprockets see page 233
DEDICATED WIDTHS
164
3110, 3120 AND C24 SERIES 2” PITCH, HEAVY DUTY, RAISED RIB
Installation guidelines
The modular plastic belts 3120, 3110 and C24 are used in combination with combs for the head transfer of the products. Different combs and sprockets are available for the maximum flexibility in conveyor lay-out definition.See page 293 for the recommended sprocket/comb matching.
Benefits
Uniform and optimum conveying surface
The ideal ratio rib thickness/spacing offers high support for the most unstable products such as PET bottles with petaloid bottom.
Reliable drive
Accurate tooth profile with a large cross section ensures high capacity and long wear life of sprockets and modules.The central pocket makes these belts bidirectional.
Easy assembly and disassembly of the belt
These belts have retaining clips for easy assembly and disassembly.
In particular 3120 belts have integrated clips located into the module, which can be easily rotated to remove the rod.
Range
3110: High mechanical strength
Due to its high working load, the 3110 belt can be used for the most demanding applications such as process conveyors with high product load and long distance.The cross rib design offers high lateral strength.
C24: Good combination open area/mechanical strength
Optimum liquid drainage and good mechanical strength.
3120: Optimum combination open area/mechanical strength
Very good liquid drainage and mechanical strength.
MODULAR PLASTIC BELTS
165
Dimension mm inches E 7,2 .283 H 23,9 .941 L 7,9 .311 P 50,8 2 R 9,7 .382 RD 76,2 3 T 14,2 .560
3110 SERIES - 2” PITCH, RAISED RIB
Standard MaterialsProducts Ref. PPRaised Rib 3110
Belt widths: 12” (304,8 mm) or wider in 3” (76,2 mm) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 27380 N/m (1,880 lb/ft) - Open surface: 26%
The ideal ratio rib thickness/spacing offers high support even for the most unstable products such as PET bottles with petaloid bottom. Very good liquid drainage and mechanical strength. Due to its high working load, the 3110 belt can be used for the most demanding applications such as process conveyors with high product load and long distance. The open area of raised rib belt guarantees optimum drainage of liquids and mechanical strength; it is also designed for easy cleaning and cooling or warming of products. The cross rib design offers high lateral strength.
BELT NOMINAL WIDTH “W”
POLYPROPYLENE PP BELT WEIGHT
REGINA REF.
mm inches kg/m lbs/ft
304,8 12 3110 PP 012 3,50 2.35
381,0 15 3110 PP 015 4,35 2.92
457,2 18 3110 PP 018 5,21 3.50
533,4 21 3110 PP 021 6,06 4.07
609,6 24 3110 PP 024 6,93 4.66
685,8 27 3110 PP 027 7,78 5.23
762,0 30 3110 PP 030 8,64 5.81
838,2 33 3110 PP 033 9,49 6.38
914,4 36 3110 PP 036 10,35 6.96
990,6 39 3110 PP 039 11,20 7.53
1066,8 42 3110 PP 042 12,07 8.11
1143,0 45 3110 PP 045 12,92 8.68
1219,2 48 3110 PP 048 13,78 9.26
1295,4 51 3110 PP 051 14,63 9.83
1371,6 54 3110 PP 054 15,50 10.42
1447,8 57 3110 PP 057 16,35 10.99
1524,0 60 3110 PP 060 17,21 11.57
Belts wider than 1524 mm (60”) available, with increments of 76,2 mm (3”). Belt available in the requested length.Example: 60 + 3 = 63 inches Ref. 3110 PP 063.
Sprockets see pages 234÷235
Belt materialsee page 13
Sprocket positioning see pages 321÷322
Combs see page 292
3110 (Raised Rib - 2” Pitch)
MODULAR BELTS
166
3120 SERIES - 2” PITCH, RAISED RIB
Standard MaterialsProducts Ref. PPRaised Rib 3120
Belt widths: 12” (304,8 mm) or wider in 3” (76,2 mm) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 24670 N/m (1,690 lb/ft) - Open surface: 29%
The ideal ratio rib thickness/spacing offers high support even for the most unstable products such as PET bottles with petaloid bottom.The open area of raised rib belt guarantees optimum drainage of liquids and mechanical strength; it is also designed for easy cleaning and cooling or warming of products.
Dimension mm inches E 7,2 .283 H 23,9 .941 L 7,9 .311 P 50,8 2 R 9,7 .382 RD 76,2 3 T 14,2 .560
BELT NOMINAL WIDTH “W”
POLYPROPYLENE PP BELT WEIGHT
REGINA REF.
mm inches kg/m lbs/ft
304,8 12 3120 PP 012 3,30 2.22
381,0 15 3120 PP 015 4,13 2.78
457,2 18 3120 PP 018 4,94 3.32
533,4 21 3120 PP 021 5,78 3.88
609,6 24 3120 PP 024 6,58 4.42
685,8 27 3120 PP 027 7,40 4.97
762,0 30 3120 PP 030 8,21 5.52
838,2 33 3120 PP 033 9,05 6.08
914,4 36 3120 PP 036 9,84 6.61
990,6 39 3120 PP 039 10,66 7.16
1066,8 42 3120 PP 042 11,18 7.51
1143,0 45 3120 PP 045 12,31 8.27
1219,2 48 3120 PP 048 13,11 8.81
1295,4 51 3120 PP 051 13,93 9.36
1371,6 54 3120 PP 054 14,74 9.91
1447,8 57 3120 PP 057 15,58 10.47
1524,0 60 3120 PP 060 16,37 11.00
Belts wider than 1524 mm (60”) available, with increments of 76,2 mm (3”). Belt available in the requested length.Example: 60 + 3 = 63 inches Ref. 3120 PP 063. On request, belts available in 1.5” (38,1 mm) increments, starting from 12” (304,8 mm). Example: 45+1.5 = 46.5 inches Ref. 3120 PP 046M
3120 (Raised Rib - 2” Pitch)
MODULAR BELTS
Sprockets see pages 234÷235
Belt materialsee page 13
Sprocket positioning see pages 321÷322
Combs see page 292
167
C24 CAM-CLEAN® SERIES 2” PITCH, RAISED RIB
Standard MaterialsProducts Ref. PPRaised Rib C24
Belt widths: 12” (304,8 mm) or wider in 3” (76,2 mm) increments - Pin material: PP- Polypropylene - Working Load (at 25°C/77°F): 18500 N/m (1,270 lb/ft) - Open surface: 30%
The ideal ratio rib thickness/spacing offers high support even for the most unstable products such as PET bottles with petaloid bottom.The open area of raised rib belt guarantees optimum drainage of liquids and mechanical strength; it is also designed for easy cleaning and cooling or warming of products.
Dimension mm inches E 6,20 .244 H 22,2 .874 L 7,9 .311 P 50,8 2 R 9,5 .374 RD 76,2 3 T 12,7 .5
BELT NOMINAL WIDTH “W”
POLYPROPYLENE PP BELT WEIGHT
REGINA REF.
mm inches kg/m lbs/ft
304,8 12 C24 PP 012 2,91 1.96
381,0 15 C24 PP 015 3,64 2.45
457,2 18 C24 PP 018 4,37 2.94
533,4 21 C24 PP 021 4,91 3.30
609,6 24 C24 PP 024 5,82 3.91
685,8 27 C24 PP 027 6,54 4.40
762,0 30 C24 PP 030 7,27 4.89
838,2 33 C24 PP 033 8,00 5.38
914,4 36 C24 PP 036 8,73 5.87
990,6 39 C24 PP 039 9,45 6.35
1066,8 42 C24 PP 042 10,18 6.84
1143,0 45 C24 PP 045 10,90 7.33
1219,2 48 C24 PP 048 11,64 7.82
1295,4 51 C24 PP 051 12,36 8.31
1371,6 54 C24 PP 054 13,08 8.79
1447,8 57 C24 PP 057 13,81 9.28
1524,0 60 C24 PP 060 14,53 9.77
Belts wider than 1524 mm (60”) available, with increments of 76,2 mm (3”). Belt available in the requested length.Example: 60 + 3 = 63 inches Ref. C24 PP 063. On request, belts available in 1” (25,4 mm) increments, starting from 12” (304,8 mm). Example: 45+1 = 46 inches Ref. C24 PP 046
C24 (Raised Rib - 2” Pitch)
MODULAR BELTS
Sprockets see pages 234÷235
Belt materialsee page 13
Sprocket positioning see pages 321÷322
Combs see page 292