marelli ecp decode - eng.pdf

8/11/2019 Marelli ECP Decode - ENG.pdf

1/6

EcuVonix Solut ions - www.ecuvonix.com - [email protected]

MARELLI ECPDECODE

This new interface allows you to decode with IMMO-OFF or Virgin mostMarelli ECU (59F; 5AF; 4AF; 4EF; 5NF - Hardware > 100 and < 100). NoBoot, No Open ECU, No computer use, all in one minute. It is able to recognizeautomatically the type of ECU, and to verify the current status through LED.

Support Ecu List:

Magneti Marelli59F.xx Hw 002

Magneti Marelli59F.xx Hw 003, 004, 005Magneti Marelli59F.xx Hw 023, 024, 025Magneti Marelli59F.xx Hw da 100a 607Magneti Marelli 5AM e 5AFMagneti Marelli4AF.xx Hw204Magneti Marelli4AF.xx Hw 407Magneti Marelli4EF.xx Hw 203Magneti Marelli5NF.xx Hw 102Magneti Marelli5NF.xx Hw 104

Magneti Marelli6JF.xx Hw 01B, 01C, 1BM


2/6


INSTRUCTIONS

First you need to connect the interface to the ECU via Pin-Out. After connecting, supply power to a battery oruse a stabilized power supply 12 volt (min 1A). Note that the Green Led STARTflashes indicating the statusof StandBy. The instrument is ready for switching to operating mode.

DECODING

To begin the process of decoding press the ON/OFF buttononce (Green LED START);now the interface queries the ECU and displays by the REDLEDand the LED ORANGEthe current code this:

Redand OrangeLED ONThe ecu is CODE ON.Led Orange ONThe ecu isVirgin.Led RossoON-> The ecu is IMMO-OFF.

1)At this point it is selected with the ON/OFF decoding tobe performed, Virgin or IMMO-OFF. Note the Led turns onVirginor IMMO-OFFdepending on the selection.

2) Immediately after the press DECODE button to startdecoding. During this phase, lasts about one minute, we seethe flashing LEDVirginor IMMO-OFFindicating the start ofdecoding.

Just finished the cycle of 1 minute, the interface againexamining the ECU to make sure that the selected decodingis successful.

Clear DTC error

To begin the process of decoding press the ON/OFF buttononce (Green LED START);now the interface queries the ECU and displays by the REDLEDand the LED ORANGEthe current code

1)Hold for 2 seconds, the ON / OFF button; interface Clearthe error is present in the back position StandBy.

2)Remove power from the Interface.

Pin 1 : - 12 Volt (Massa)Pin 4 : K Line

Pin 6 : +12 Volt (Key On)Pin 9 : +12 Volt

WARNING:In the event that the ECU does not communicate, the interface indicates the error with

the flashing of all LEDs for 3 seconds, returning to the position of StandBy.


3/6


Pin Out Iaw 59F.xx / 5AF.xx


4/6


Pin Out Iaw 4AF.xx / 4EF.xx


5/6


Pin Out Iaw 5NF.xx

Connettore MPin 5 :-> Massa (Ground)

ConnettoreVPin 16 :-> +12Volt

Pin 12 :-> +12Volt (Key On)Pin 10 :-> K Line


6/6


Pin Out Iaw 6JF.xx

Pin 1 :-> Massa (Ground)Pin 50 :-> +12Volt

Pin 23 :-> +12Volt (Key On)Pin 88 :-> K Line

marelli ecp decode - eng.pdf

Documents