PAGE 514 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

SH

OT

GU

N T

OO

LSSP

EC

IALT

Y H

AN

DG

UN

TO

OLS

Gives the forcing cone a gentle taper that reduces recoil and improves shot patterns. Spiral flutes give a chatter-free cut on all types of barrel steel. The long shank lets you alter most barrels using only a large tap handle to turn the reamer. abSPECS: M-7 High Speed Steel. 8-flute, right-hand cut with left-hand spiral. 9" (22.9) long, 31/2" (8.9cm) shank, 7/16" square.

MANSON PRECISION SPIRAL FLUTE LONG FORCING CONE REAMER

8 Flutes Give Smooth, Efficient Cutting

#513-010-012AQ 12 Ga. Forcing Cone Reamer, 3A92M95 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 92.95

Cutter removes metal from damaged rim-recess areas. Solder ring in place, recut rim. abSPECS: 55° Cutter - M-7 H/Speed Steel. 51/4" (13.3cm) long. Bronze pilot bushing. Rings - 1031 steel. Approx. 1/4" (6.3mm) long.

CLYMER SHOTGUN RIM CUTTER & HEADSPACE RING

Restore Headspace To Shotgun Chambers

#184-115-012AQ 12 Ga. Rim Cutter, 4H115K00 � � � � � $ 115.00#184-115-020AQ 20 Ga. Rim Cutter, 4H115K00 � � � � � 115.00#184-116-012AQ 12 Ga. Headspace Ring, 4H12P00 � 12.00

Face-off shotgun barrels exactly square to the bore. Ideal

when repairing dings, or before installing screw-in chokes. Smooth cutting, five-flute cutter. Turn with hand drill or drill press. abSPECS: H.S. steel. 33/4" (9.5cm) long. 15/16" (24mm) dia. 3/8" (9.5) dia. shank. Pilot NOT included, order below.

CLYMER

SHOTGUN BARREL FACERAccurately Squares Barrel;

No Lathe!

#184-352-000AQ Shotgun Facer, no pilot, 4H85M00 � � � � � � � � � � � � � � � � � � � � � � � � � $ 85.00

STOCK # SIZE GAUGE#184-252-725AQ .725 12#184-252-729AQ .729 12#184-252-610AQ .610 20

STOCK # SIZE GAUGE#184-252-612AQ .612 20#184-252-614AQ .614 20

CHAMBER REAMER/BARREL FACER PILOTS, ONLY

— Advise # — Chamber Reamer Pilot, 4H12L00 � � � $ 12.00

Hundreds of abra-sive “balls” mounted on a flexible shaft -

the fastest, easiest way we’ve come across to clean and polish older barrels or put a mirror polish in new ones. For used bar-rels, the Medium-Coarse hone, followed by the Fine, removes rough and tight spots and brings the bore to a bright finish that you can see and feel . . . just run a patch through it before and after; the difference is amazing! We found too, that we could feel tight spots during honing and spend extra time on them until they were evened out. On new barrels, the Fine hone by itself will bring the factory finish up to a beautiful, mirror-bright finish that’s a real customer pleaser. Easy to use: chuck in a variable speed electric drill; wet the hone with Flex Hone® oil; start the drill and insert the hone into the barrel from the breech end (if possible). As it cuts, a slurry of abrasive and oil develops to help speed the cutting action. Flex Hone® available in sets and individual hones for 10, 12, 16 and 20 gauge barrels as well as .410 bore. Also, special-sized hones for 10, 12, 16, 20 gauge chambers and .410 bore. Instructions walk you through the steps for a perfect job. (You MUST use Flex Hone® oil - all other oils will destroy the abrasive “balls” and void our guarantee!) 750 RPM MAX. Avoid excess pressure. abSPECS: Flex Hone® for Barrels; 10, 12, 16, 20 ga., .410 bore. 33" (83.8cm) long in Med.-Coarse grit (red tip) or Fine grit (light blue tip). Flex Hone® for Chambers; 10, 12, 16, 20 ga., .410 bore 12" (6.5cm) long, fine grit (light blue only). Set includes Med.-Coarse & Fine barrel hones, Chamber hone & 1 qt. Flex Hone® oil, for 1 ga.

FLEX HONE OIL - Specially formulated for use with Flex Hones. Contains both honing and lapping oils in a petroleum base that will not harm aluminum, brass or steel. (Use of other oils de-stroys abrasive ball and voids guarantee.)

#080-609-008AQ 1/2 Pint Flex Hone Oil, 1B9N99 � � � � � � $ 13.49#080-609-000AQ Quart Flex Hone Oil, 1B15Q83 � � � � � � 21.98

SHOTGUN BARREL POLISHING FLEX HONE®

Puts Finish Polish On Shotgun Bores

That Is Truly Outstanding

#076-200-156AQ Flex Hone® Inst. please request, 6G00NDQ � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ .00

FLEX- HONE SIZE

FINE BORE

$66.99

MED. BORE $52.99

CHAMBER $52.99

ONE GA. SET

$161.9910 ga #080-607-210AQ #080-606-110AQ #080-608-510AQ NA12 ga #080-607-212AQ #080-606-112AQ #080-608-512AQ #080-605-012AQ16 ga #080-607-216AQ #080-606-116AQ #080-608-516AQ #080-605-016AQ20 ga #080-607-220AQ #080-606-120AQ #080-608-520AQ #080-605-020AQ.410 #080-607-241AQ #080-606-141AQ #080-608-541AQ #080-605-041AQ

SCREW-IN CHOKE INSTALLATION REQUIREMENTS Before accepting a barrel for machining to accept screw-in chokes, you must measure the outside diameter

(O.D.) to determine if there will be sufficient wall thickness after machining. “Mike” the O.D. of the barrel and the O.D. of the tap for the particular gauge. Subtract the O.D. of the tap from that of the barrel, divide by 2, and this will give the wall thickness after machining, providing the O.D. of the barrel is concentric with the inside diameter (I.D.). A sample calculation appears below.

Barrel O.D. (12 Ga) .850"Tap O.D. (12 Ga) Win-Choke™ – .814" .036" ÷ 2 = . 018" Wall Thickness

We DO NOT recommend installations in barrels where the resultant wall thickness will be less than .015", providing the I.D. of the barrel is concentric with the O.D. If the I.D. is not concentric with the O.D., you will have to make your own decision as to whether the installation will be safe. In addition, you CANNOT install screw-in chokes in barrels whose inside diameters (I.D.) exceed the following dimensions: 10 ga. - .780"; 12 ga. - .735"; 12 ga. Thinwall - .728"; 16 ga. - .666"; 20 ga. - .624". Exceeding these dimensions WILL CAUSE DAMAGED CHOKE TUBES and there is a GREAT POSSIBILITY OF CAUSING A BARREL BLOW-OUT! Check EVERY installation before firing to make sure the tube does not protrude into the bore. Back-bored or jug-choked barrels are usually NOT suitable for screw-in choke installation.

The finishing touch for forcing cones cut with Long Forcing Cone Reamers. Taper matches perfectly so the maxi-mum amount of abrasive media contacts the barrel’s surface for faster, more effective polishing action, with less elbow grease and work. Must be used with Flex Hone Oil; use of other oils will destroy the abrasive balls and void the guarantee. abSPECS: Medium or Fine grit. 10" (25cm) overall length. Abrasive head, 1.625" (4.1cm) long. 12 ga. tapers from .710" to .798" in diameter. 16 ga. tapers from .665" to .745" diameter. 20 ga. tapers from .615" to .699" diameter.

FORCING CONE FLEX HONE®Tapered Design

Polishes Quickly & Efficiently

#080-606-512AQ 12 Ga. Medium Grit Flex Hone, 1B35P61 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 44.99

#080-607-512AQ 12 Ga. Fine Grit Flex Hone, 1B49G99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 65.99

#080-607-516AQ 16 Ga. Fine Grit Flex Hone, 1B49M99 � � � � � � � � � � � � � � � � � � � � � � � � � � 65.99

#080-606-520AQ 20 Ga. Medium Grit Flex Hone, 1B32M99 � � � � � � � � � � � � � � � � � � � � � � � � � � 43.99

#080-607-520AQ 20 Ga. Fine Grit Flex Hone, 1B49A99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 65.99

#080-609-008AQ 1/2 Pint Flex Hone Oil, 1B9N99 � � � � � 13.49#080-609-000AQ Quart Flex Hone Oil, 1B15Q83 � � � � � 21.98

Quickly brings your shotgun bore to a like new or better polish. Five grits provide fast, smooth polishing for chrome lined and carbon steel barels; 500 grit, 400 grit, 150 grit, 150 grit for chrome bores and a 2-S

Lisle stone. Steel carrier, riveted to arm, fits Lisle No. 2 Barrel Hone. abSPECS: Aluminum oxide stones, steel carrier. Pak of 2 stones and arms. Kit contains 2 stones of each grit. Plastic storage box.

PROFESSIONAL SERIES BARREL HONING STONES

Gives Shotgun Bore A Good-As-New Polish

#080-000-011AQ 500 Grit Profess. Stones, 8K9G73 � � � $ 13.99#080-000-012AQ 400 Grit Professional Stones,

8K9I73 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13.99#080-000-013AQ 150 Grit Professional Stones,

8K9Q73 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13.99#080-000-014AQ 150 Grit Chrome Bore Stones,

8K10C49 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15.99#080-000-016AQ Professional Honing Stone Kit,

8K38H41 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 52.99

Ample range for 28 ga. to 12 ga. Flex-drive eliminates chat-ter, gouging. For 1/4" or larger electric drill. Included in choke set. abSPECS: 1/4" (6.3mm) shaft, 81/2" (21.6cm) long.

BARREL HONE EXTENSION SHAFT - Piloted shaft attaches to your electric hand drill motor and accepts Brownells Barrel Hones. Keeps the hone in the center of the bore; prevents ex-pensive damage; lets the hone do all the work for faster, better looking results. Includes abrasive paper holder and a threaded adapter that accepts all 5/16"-27 tpi shotgun brushes and mops.

#080-915-000AQ Barrel Hone Extension Shaft, 8K60D82 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 78.99

LISLE

SHOTGUN BARREL HONE

#531-108-002AQ No. 2 Barrel Hone, 1C14K99 � � � � � � � � $ 14.99#531-107-602AQ No. 2-S Stones, only, 1C3C99 � � � � � � � 3.99

Brings Bores & Chokes Back to New-Or-Better Polish

No. 2-S

Here are the three Magna®-Tip bits you’ll need to install and remove our custom grip screws. Although we picked them to match our screws, they’ll fit other brands too. abSPECS: Steel, heat treated. Allen: 3/32" hex. Slotted: 240-5. TORX: T-15. Fit Brownells 1911 Auto and Ruger MkI/MkII grip screws.

GRIP SCREW BITS

Allen®, TORX® & Slotted Bits Fit Right

#080-185-100AQ 3/32" Allen Bit, 8K2J52 � � � � � � � � � � � � � � � � $ 2.99#080-240-540AQ #240-5 Slotted Bit, 8K2P52 � � � � � � � � � � 2.99

Five, precision-machined gunsmith punches equip you to handle a wide variety of any pistol disassembly and reassembly jobs. Nontapered, with a flat tip for removing solid pins—excellent for drifting sight pins in and out. Kit includes four, steel punches through-hardened for maximum strength and a non-marring brass drift punch for jobs where the gun’s finish must be protected. Knurled handles ensure a firm grip to prevent slippage and protect your gun’s finish from

scratches and scuffs. abSPECS: Pin punches - 4140 chrome-moly steel. 1/16", 3/32", 1/8", 5/32" diam-eters. 31/2" to 41/2" OAL. Drift punch - Brass. 31/4" (8.3cm) long x 3/16" (4.8cm) diameter.

LYMAN PISTOL PUNCH SET

#539-000-019AQ Pistol Punch Set, 5K14E36 � � � � � � � � $ 16.99

Most Common Sizes Used On Pistol Projects

The extra reach you need for full-length bore polishing with Brownells Barrel Hones and your electric hand drill. Piloted to keep the hone centered for faster, better results. Abrasive paper holder helps remove tight spots before honing; 5/16"-27 tpi shot-gun bore brush adapter lets you do heavy duty cleaning. abSPECS: Kit includes: Shaft - steel, 28" (71cm) long, 1/4" (6.3mm) dia. Pilots - Nylon, .12 ga. .715" (18mm) dia., 16 ga. .652" (16.6mm) dia., 20 ga. .605" (15.3mm) dia. Abrasive Holder - Steel, 2" (5cm) long, 1/2" (12.7mm) dia. Brush Adapter - Steel, 3/4" (19mm) long. Shaft coupling will accept .250" (6.3) dia. accessories.

12, 16, 20 GAUGE

BARREL HONE EXTENSION SHAFT

#080-915-000AQ Barrel Hone Extension Shaft, 8K60D82 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 78.99

Polish Or Clean The Entire Bore From Muzzle To Cone

For A Mirror Finish

PAGE 515Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

One convenient kit with the most needed tools for SIG maintenance. Designed for the police armorer and profes-sional gunsmith, each tool in the kit has been thoroughly field tested. ab

⑬ #2 FIXED BLADE SCREWDRIVER - Remove extractor on P229, P236, P239 stainless steel slide.

#080-451-002AQ #2 Screwdriver, 8K10A06 � � � � � � � � � � $ 11.99

⑭ #17 FIXED BLADE SCREWDRIVER - For grip screws.#080-451-017AQ #17 Screwdriver, 8K10M06 � � � � � � � � � $ 11.99

⑮ SIG SIGHT MOVER - Easy, no-mar, rear sight adjustment.#584-045-220AQ SIG Sight Mover, 4H110L00 � � � � � � $ 129.99

⑯ ANGLE POINT TWEEZERS - Puts pins in tight places.#345-415-634AQ Angle-point Tweezers, 5D6D89 � � � � $ 6.89

⑰ COTTON APPLICATORS - Clean nooks and crannies.#885-861-500AQ 500 Cotton-Tipped Applicators,

8K6K99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 8.99

⑱ CLP-16 BREAK-FREE - For cleaning and lubrication.#102-100-023AQ Break-Free CLP, 2/3 fl. oz. Bottle,

6K3F59 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 4.99

⑲ SIG COMBO TOOL - For grip screws, plus remove and in-stall mainspring, magazine catch stop, sear spring.

#719-100-000AQ SIG Combo Tool, 9A40A30 � � � � � � � � � $ 44.99

⑳ TOOL BOX - Durable, high impact plastic.#696-100-303AQ Tool Box, 6F11I98 � � � � � � � � � � � � � � � � � � $ 17.59

① #3 ROLL PIN PUNCH - For P220, P225, P226, P228 slide.#230-100-003AQ #3 Roll Pin Punch, 8K3G85 � � � � � � � � � � $ 4.99

② #4 ROLL PIN PUNCH - Removes Firing pin retainer.#230-100-004AQ #4 Roll Pin Punch, 8K3G85 � � � � � � � � � � $ 4.99

③ 3MM CUP TIP PUNCH - For firing pin positioning pin.#080-620-300AQ Long 3mm Cup Tip Punch,

8K9D88 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 11.99

④ SHORT 3MM CUP TIP PUNCH - Starter punch for firing pin positioning pin.

#080-620-301AQ Shrt 3mm Cup Tip Punch, 8K10Q47 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 12.99

⑤ STARRETT 1/16" PUNCH - Remove hammer stop pin, sear spring pin.

#827-525-780AQ 1/16" Punch, 7B6M99 � � � � � � � � � � � � � � � � � $ 6.99

⑥ STARRETT 1/8" PUNCH - Use as a slave pin.#827-525-800AQ Starrett Pin Punch, 8K5G99 � � � � � � � � � $ 5.99

⑦ STARRETT 3/32" PIN PUNCH - Use as sear shaft slave pin.#827-525-790AQ #3 Roll Pin Punch, 7B5H99 � � � � � � � � � � $ 6.49

⑧ BROWNELLS 5/64" PIN HOLDER - Holds the breech pin.#080-685-078AQ 5/64" Roll Pin Holder, 8K12E26 � � � � � � � $ 14.99

⑨ BROWNELLS 3.5MM PIN HOLDER - Holds various pins.#080-685-130AQ 3.5mm Roll Pin Holder, 8K11E98 � � � $ 14.99

⑩ 3 NYLON DRIFT PUNCHES - Install P229 extractor.#080-478-000AQ Set of 3 Nylon Front Sight Punches,

8K4K22 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 4.99

⑪ PISTOL BENCH BLOCK - No-mar nylon provides a solid surface, with large through holes, for driving pins, polishing.

#080-000-493AQ Blue Pistol Bench Block, 8D19I99 � � $ 19.99

⑫ 1" NYLON/BRASS HAMMER - Brass head for driving various pins. No-Mar nylon head is ideal for “tapping”.

#818-600-100AQ 1" Nylon/Brass Hammer Combo, 8A19A99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 19.99

TOOLS FOR SIG HANDGUNS

17

1

20

12

11

6

7

3

10

54

1514

13

9

16

18

8

2

19

#080-220-100AQ SIG Kit Tools, w/Tool Box, 8K255M60 � � � � � � � � � � � � � � � � � � � � � � � � $ 296.99

#080-220-101AQ SIG Kit Tools, No Tool Box, 8K241D24� � � � � � � � � � � � � � � � � � � � � � � � � 281.99 Superb collection of professional quality tools that makes

rebuilding and repair of the 92 Series easier and more cost ef-ficient. Designed for the police armorer and professional gun-smith, these high-quality tools will perform the tasks required, time and again, without failure. Because of the rugged de-pendability and simplicity of the Beretta 92 design only a very few specifically-designed tools are needed to keep these great pistols shooting. Each and every tool included in this kit has been thoroughly tested, and many perform specific tasks rec-ommended in the factory repair manual and are not available anywhere else. Following is a brief description of each tool con-tained in the Kit and the function it performs. And remember, when you buy the entire kit, you save both time and money. ab

⑦ BERETTA PIN PUNCHES - Sized to fit the metric roll pins on the Beretta 92 Series pistols. Set includes four punches.

#080-092-114AQ 3mm Pin Punch, 8K10P83 � � � � � � � � � � $ 15.99#080-092-074AQ 2mm Pin Punch, 8K10F83 � � � � � � � � � � 15.99#080-092-055AQ 1.5mm Pin Punch, 8K10D83 � � � � � � � � 15.99#080-092-059AQ 1.5mm Starting Punch, 8K10E83 � � � 15.99#080-092-000AQ Beretta Punch Set, 8K36A59 � � � � � � � � 50.99

⑧ 1/4"BRASS DRIFT PUNCH - A harder-than-nylon but softer-than-steel punch for drifting fixed sights without damage.

#080-920-102AQ Brass Drift Punch, 8K4F33 � � � � � � � � � � $ 4.49

⑨ BERETTA MAGAZINE LIP GAUGE - Gives a clear check of minimum/maximum magazine lip width for correct feeding.

#080-920-103AQ Magazine Lip Gauge, 8K30A40 � � � � � $ 39.99

⑩ SERIES II INDIA STONE - Great for smoothing the Beretta's sear and hammer engagement surfaces.

#080-815-000AQ Series II India Stone, 8K13J22 � � � � � $ 20.99

⑪ TRIGGER RETURN SPRING TOOL - Installs trigger return spring. Keeps hands close to the work.

#080-000-288AQ Trgr Return Sprg Tool, 8K9P00 � � � � � $ 12.99

⑫ SERIES II HARD ARKANSAS STONE - Ultra-fine-grit stones for smoothing the Beretta's sear and hammer engagement surfaces.

#080-815-001AQ Series II Hard Arkansas Stone, 8K65K46 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 79.99

① BERETTA GRIP BUSHING STAKER - Securely stakes grip bushing without frame damage. Matches factory stake.

#080-920-101AQ Beretta Grip Bushing Staker, 8K26G28 � � � � � � � � � � � � � � � � � � � � � � � � � $ 36.99

#080-920-010AQ Replacement Bushing Staker Head, only, 8K24K57 � � � � � � � � � � � � � 29.99

② 4 OZ. BALLPEEN HAMMER - Correct size and weight for driving pins, brass drift punch, etc.

#956-000-002AQ 4 oz. Ballpeen Hammer, 9D29Q98 � � $ 29.99

③ BERETTA BUSHING DRIVER BIT - Fits our MAGNA-TIP® handles to fully support the Beretta Stock Bushing.

#080-920-100AQ Beretta Bushing Driver Bit, 8K7A00 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 9.99

④ MAGNA-TIP® CLIP-TIP LAW ENFORCEMENT HANDLE - Short and small to keep hands close to the work. Clip-Tip shank minimizes bit wobble.

#080-088-001AQ Clip-Tip Law Enforcement Handle, 8K10D82 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 15.99

⑤ #300-5 MAGNA-TIP® BIT - Fits the Beretta grip screw.

⑥ 90° SCRIBE - Very handy for reaching down inside frame recesses to help maneuver smaller parts and springs.

#345-080-090AQ 90° Scribe, 8K4N99 � � � � � � � � � � � � � � � � � � $ 4.99

TOOLS & KITS FOR BERETTA 92

Every Tool That's Required For Making Complete Repairs In Both The Shop & Field

The Right Tools For Entire 92 Series – Military & Civilian

#080-920-000AQ Beretta 92 Series Tool Kit, Complete w/Tool Box, 8K209P99 � � � � � � � � � � � � � � � � � � � � � � � � $ 219.99

#080-920-110AQ Beretta Flat Storage Box, 8K13F05 � � � � � � � � � � � � � � � � � � � � � � � � � � 14.99

The Tools You Need To Fix SIGs Correctly

12

10

9

7

4

1

3

5 6

28

11

S e l e c t e d by noted pis-tolsmith Jim Garthwaite, these are the right tools for complete disassem-bly and reassembly of your Hi-Power. Jim’s innovative Ham-mer/Sear Installation Tool is part of the Kit and is also available separately. Machined out of solid aluminum, it’s designed to compress and retain the mainspring to help make sear installa-tion easy and fast. The aluminum construction ensures it won’t scrape or gouge the frame. Complete Armorer's Kit includes the Hammer/Sear tool, plus four pin punches, aluminum frame spacer, correct-size miniscrewdriver for magazine catch-lock, and complete disassembly/ assembly instructions that explain how to use the tools. abSPECS: Kit includes Hammer/Sear Installation Tool; small screwdriver; 1/16", 5/64", and 3/32" roll pin punches, 3/32" flat pin punch, aluminum frame spacer, and instructions.

GARTHWAITE BROWNING HI-POWER

ARMORER’S TOOLSThe Right Tools

For Proper Disassembly &

Assembly

#100-007-006AQ Browning Hi-Power Armorer’s Tool Kit, 6C69J00 � � � � � � � � � � � � � � � � � � � � � � � $ 79.95

#100-007-008AQ Hammer/Sear Installation Tool, 6C21F40 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24.95

Cross-slotted tip fits the elevation and windage screws on Millet pistol sights. Help eliminate gouging and marring of the screws. abSPECS: 11/2" (3.8cm) long.

MAGNA-TIP® MILLET REAR SIGHT BITFits Perfectly; Won’t Blemish The Sight

#080-147-000AQ Millet Rear Sight Bit, 8K3C40 � � � � � � � $ 4.99

Tray

High-density polymer block supports S&W M&P and Glock polymer-framed pistols without marring and helps with ar-mory work and disassembly. Special design relieves pres-sure from critical function surfaces and gives easy access to all pins. Moveable bosses quickly adjust to hold different size frames. Holes and slots accommodate thumb safety and maga-zine disconnect. Fixed bosses — one for .45 and the other for 9mm/.40/.357 — hold striker to ease striker spring removal and installation. Special trigger bar block makes it easy to swap trig-gers. Armorer’s Tray attaches to the underside of the block, el-evating the work surface nearly an inch, while the interior and embedded magnet keep pins and small steel parts from rolling away. Raised edges in the center support the muzzle when tak-ing off slide back plates. Comes with a 1/16" Allen wrench for the rear sight screw and a 1/8" roll pin punch that seats into coil roll pins in M&P frames and drives the pins far enough to be out of the way but not ejected. Storage slots in the tray for punch and wrench. abSPECS: Polymer, red. Block - 7" (17.7cm) long, 4" (10cm) wide, 1½" (3.8cm) high. Tray - 7" long, 4" wide, .9" (2.3cm) high.

APEX TACTICAL

POLYMER ARMORER’S BLOCK & TRAY

Supports Polymer-Framed Pistols For Armory Work & Disassembly

Block (Gun Not Included)

#100-011-660AQ Polymer Armorer’s Block, 7F25D70 � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

100-014-075AQ Polymer Armorer's Tray, 7F21F50 � � � � � � � � � � � � � � � � � � � � � � � � � 24.99

Tray

PAGE 516 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

w

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

High-strength poly-mer magazine well insert

fits double-stack Beretta, SIG, and Taurus pistols. Slides into the mag well and locks tight using the factory latch, so the other end of the block can be clamped in a vise. Supports the pistol for cleaning, maintenance, and other servicing, while it keeps both hands free to do the work. Durable, injection-molded polymer composite construction won’t mar or scratch gun and resists most common cleaning solvents. To ensure a snug fit in your pistol, the ridge on the back of the stem may need to be filed down. abSPECS: Polymer, black. Stem – 45/16" (11cm) long. Fits Beretta 92/96, SIG P226/228/229, and Taurus PT-99/-101.

C.B. GIORNESTO BERETTA/SIG/TAURUS

VISE BLOCKSecure, Hands-Free

Support Of Pistol For Cleaning & Maintenance

#100-005-890AQ Beretta/SIG/Taurus Vise Block, 6B31N17 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

Specialized tool designed by the factory allows the user to restore older magazines to original specs and tune new magazines for maxi-mum reliability. Prevents damage to delicate feed lips often caused by makeshift tools. abSPECS: Steel, black matte finish. 43/4" OAL. Includes complete instruc-tions.

HIGH STANDARD .22 LR PISTOL

MAGAZINE LIP ADJUSTMENT TOOLCorrects Feeding Problems

#430-000-569AQ Magazine Lip Adjustment Tool, 3D29F50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

Specialized pliers allow Glock owners to remove the base pad from factory magazines

without gouging or cracking the plastic. Small crimping tips contact the magazine precisely above the locking tabs. Hard-ened, steel handles feature the correct geometric curvature to prevent over-compression of the magazine sidewalls. abSPECS: Steel, black finish. 6" (15.2cm) long.

MAGAZINE TOOL for GLOCK®Removes Base Pads

Fast, Without Damage

#080-000-191AQ Magazine Tool For Glock, 8K18C72 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 22.99

Precision-made tools that will take care of most any field repair on the entire family of Glock pistols. Kit includes: 3/16" nut driver for front sight re-moval; .050" Allen wrench for rear sight removal, installation and adjustment; 3/32" takedown punch. Tools feature hardened shafts and aluminum handles in a vinyl pouch. abSPECS: Shaft - steel, blued. Handle - aluminum, anodized red. 33/4" (9.5cm) long. 3/16" Nut Driver available separately.

ARO-TEK™

ARMORER'S TOOLS for GLOCK®Every Tool You Need To

Work On A GLOCK Pistol

#066-800-200AQ Tool Kit for Glock, 6F36A00 � � � � � � � � $ 45.00#066-800-300AQ 3/16" Nut Driver, 6F20K00 � � � � � � � � � � � 25.00

Built specifically for Glock pistols, our punch kit features a tip that is easily replaced if it ever bends or breaks. Punch is ideal for removing the lock-ing block pin, trigger housing pin, trigger pin, and can be used to depress the magazine floorplate catch. Handle is made of fatigueproof C.R.S. steel, with a tensile strength of over 140,000 psi, and includes a knurled-chuck to hold the tip securely in place. Replaceable tips are made of tool steel, and oil hardend to Rc 58-60, with beveled heads annealed to Rc 42-45. Kit in-cludes one handle and one tip. Additional replacement tips are sold separately. abSPECS: Handle - 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 21/2" (6.3cm) long.

REPLACEABLE PIN PUNCH for GLOCK®

Saves You From Buying All New Pin Punches

#080-001-121AQ Replaceable Pin Punch Kit for Glock, 8K8I00 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 9.99

#080-001-120AQ Replacment Pin, Glock, 8K3E50 � � � � � 4.99

Easy-to-use tool helps you remove factory front sights and install aftermarket sights. The punch is just the right size for depressing front sight center spreader; hex wrench holds and tightens the small retaining nut for the replacement sight. Non-slip knurled grip. abSPECS: Delrin® handle. Steel punch and wrench. Black. 3/32" (2.3mm) punch. 51/4" (13.3cm) long. Will not work for models 17L, 34, 35, 24 and 24C..

B&J MACHINE

COMBINATION TOOL for GLOCK®Handy Tool Makes

Glock Sight Changes Easier

#694-301-100AQ Combination Sight Tool for Glock, 4F17D13 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 22.95

Original Glock fac-tory disassembly tool lets you completely disas-semble any Glock pistol. Assists in removal locking block pin, trigger housing pin, and trigger pin. Depresses magazine floor-plate catch for removal of plate for cleaning or replacement of spring and follower. Hardened steel pin shaft with deeply ridged, easy-to-grasp polymer handle.SPECS: Steel with polymer handle, black. 33/4" (9.5cm) O.A.L. 13/8" (3.5mm) shank length. .100" (2.5mm) shank diameter.

DISASSEMBLY TOOL for GLOCK®Makes Stripping Your

Glock Fast & Easy

#100-005-935AQ Disassembly Tool, 1D6B40 � � � � � � � � � � $ 7.99

Completely disassemble any Glock pistol with this handy punch. Large wooden handle lets you to comfort-ably push out the locking block, trigger housing, and trigger pins. Tool is also ideal for disassembling the magazine floorplate. ab

GRACE USA DISASSEMBLY TOOL for GLOCK®

Lets You Easily Disassemble Any Glock Pistol

#354-000-039AQ 3/32" Punch Glock® , 4E8C49 � � � � � � � � � � $ 9.99

Multi-function tool lets you do a complete disassembly, change sights, replace parts, even give your favorite Glock a quick brushing off. Features a 3/32" pin punch, 3/16" flat blade for connector removal, 3/16" sight nut driver and a cleanup brush. Pocket clip for handy carry. abSPECS: Brass body, stainless steel pin punch. 5" (12.7cm) O.A.L.

LONE WOLF DIST.

ULTIMATE ARMORER’S TOOL for GLOCK®

Just One Tool For Complete Maintenance,

Disassembly

#100-000-774AQ Ultimate Armorer’s Tool, 2K18K49 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 20.99

Stainless steel tool is precisely machined to hold the Glock channel liner securely during removal and installation. Unique double-headed design has threaded end for removal and smooth end for installation. Makes a delicate job quick and easy while pre-venting damage to slide and liner that can occur when using makeshift tools. abSPECS: Stainless steel. 43/4" length. Instructions included.

JENTRA

CHANNEL LINER TOOL for GLOCK®The Correct Tool For

Removal & Installation

#463-000-009AQ Channel Liner Tool, 3F21N95 � � � � � � $ 21.95

The same tool used at the Glock Factory to accurately remove and

install the firing pin channel liner. The disposable liner must be removed, and a new one installed, when rebluing or refin-ishing. Easy-to-use tool will not damage or mark the slide. In-cludes complete instructions, plus one channel liner. abSPECS: Steel, blue. 6" (15cm) long. Fits all models of Glock pistols.

RIMFIRE GUN WORKS

CHANNEL LINER TOOL for GLOCK®Removes & Installs

Liners Without Slide Damage

#777-100-017AQ Channel Liner Tool for Glock, 7G27Q15 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 27.15

Plastic tool engages Glock slide lock and provides me-chanical advantage to ease slide removal. Fits all Glock models with standard and extended slide locks. Texture lines provide plen-

ty of purchase for thumb and finger, while the bright yellow color makes this tool easy to find in your toolbox or on your bench. abSPECS: Plastic, yellow.

GTUL

SLIDE REMOVAL TOOL for GLOCK®Makes It Easy To Remove

Glock Slide

#100-011-518AQ Slide Removal Tool for Glock, 2C9C79 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 11.95

Solid, high-strength vise block holds Glock pistols securely for easy cleaning and maintenance. Keeps both hands free for detailed, precision work and helps eliminate the chance of dropping the pistol and causing dam-age. Slides into the mag well and locks tight using the factory latch without marring or scratching. Durable, poly-mer composite construction is resis-tant to most solvents. Fits all 9mm and .40 cal. Glock pistols. abSPECS: Polymer, black. Stem - 41/4" (10.8cm) long x 11/4" (3.2cm) wide.

C.B. GIORNESTO

THE GLOK BLOK for GLOCK®Holds Pistol Securely For

Easy Cleaning & Maintenance Using Both Hands

#100-003-691AQ Glok Blok, 6B32H00 � � � � � � � � � � � � � � � $ 39.95

Steel tool is specially shaped to fit beneath the pin recess of Ruger LCP slide stop for simple removal, letting you clean the gun or perform maintenance. Makes process fast and easy compared to using your fingertips. Durable plastic handle gives long service life and is specially contoured to aid grip. abSPECS: 1018 steel, black oxide finish.

RUGER® LCP

SLIDE STOP PIN REMOVAL TOOL

Eases Slide Stop Pin Removal On Popular

Carry Pistol

#080-001-093AQ LCP Slide Stop Pin Tool, 8K11F80 � � $ 15.99

We redesigned our original Replaceable Pin Punch to cre-ate the perfect length and size for driving roll pins on S&W M&P pistols. The handle features a removable knurled chuck to hold the bevel-headed punch pin, as well as checkering on the body to ensure a solid grip. Small center nub on the end of the punch seats into roll pins and helps prevent slipping and damaging your firearm. Punch tip is made of tool steel and hardened to Rc 54-58 for increased durability, with replacement pins available if original is bent or broken. abSPECS: Steel. Handle - 3" (7.6cm) long x 3/8" (.95cm) diameter. Pin – 1.5" (3.8cm) long x .122" (.3cm) diameter.

/APEX TACTICAL S&W M&P

HEAVY DUTY PIN PUNCHSpecifically Designed For

Removing M&P Series Roll Pins

080-001-103AQ Heavy Duty Pin Punch, 8K10B00 � � � $ 12.99 080-001-101AQ Replacement Pin, 8K3G80 � � � � � � � � � 4.99

Multi-use tool with large, easy-to- grasp handle performs several maintenance and repair tasks. Removes grip screws, mainspring assembly; provides controlled removal of mainspring. Installs and removes sear spring and magazine catch. Handy to have on the bench, in-dispensable for emergencies in the field.SPECS: Plastic handle, steel shank. Approximately 71/2" (19cm) long. Four interchangeable bits. Fits 220, 225, 226, 228, 229, 230, 232. 239, 245.

SIG SAUER COMBO TOOLHandy Tool For Bench

Or Field Use

#719-100-000AQ SIG Combo Tool, 9A40A30 � � � � � � � $ 44.99

PAGE 517Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

Small, self-contained, take-down tool has everything you need to field strip your Ruger Mark I or II pistol. The tool’s aluminum end cap has a steel, wire loop for removing the mainspring hous-ing latch. Punch on opposite end drives out the bolt stop pin without marring the metal. Unscrew end cap to expose a pin for removing the extractor, plunger and spring for cleaning or replacement. abSPECS: Body/Punch - Delrin, black. Extractor Tool - Aluminum/steel. 37/8" (cm) OAL, 1/2" (1.3cm) diameter.

GUNSMITHER TOOLS RUGER® MARK I/II

TAKEDOWN TOOLDisassemble Your .22 Auto

Fast & Easily

#100-001-507AQ Ruger Mark I/II Takedown Tool, 7A11M50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 13.95

Made of heavy duty del-rin, this multipurpose tool makes the disassembly and reassembly of Ruger rimfire pistols quick and easy. Assists in removing the mainspring housing, bolt and recoil spring, and removing the upper re-ceiver from the frame. When it’s time for reassembly, the

tool helps get the recoil spring back on the bolt, ensure the internal mechanisms are aligned before insertion of the bolt, plus it gives you the proper grip and pressure needed to get the mainspring housing pin back into the gun. Tool can even be used to push down the follower button when loading the magazine. Tool available alone or with a durable cardboard stand that provides a stable platform to hold the pistol and free up your second hand. ab

THE RIGHT TOOL CO. RUGER® MARK I/II/III & 22/45

ALL-IN-ONE TOOLMakes Cleaning Your Pistol

Hassle Free

#100-015-788AQ All-In-One Tool, 4R19K30 � � � � � � � � � � $ 21.95#100-015-789AQ All-In-One Tool & Stand,

4R24J00 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27.95

Ultra-compact, pocket tool makes disassembly of Sig Sauer pistols fast and easy. Use to remove or install grip screws, magazine catch and support plate, pivot pins, sear and decocker springs, and the mainspring assembly on both

current-production and older pistols. Also aids in disassem-bling magazines for cleaning and maintenance. Strong inter-nal magnets retain the replaceable (1/4" hex drive) screwdriver bit and help keep small parts from rolling away during disas-sembly. abSPECS: Body – 6061 T6 aluminum, hardcoat anodized, matte black. Driver Bit & Disassembly Pin Punch – stainless steel. 21/2" (6.35cm) long, 1/2" (1.27cm) wide, 3/4" (1.9cm) high. 1.6 oz. (45g) weight. For Sig Sauer P220, P225, P226, P228, P239, and P245 DA/SA models. Instructions included.

SIG SAUER PISTOL SPD TOOLFor Fast, Easy Field-Stripping Of Sig Pistols; Fits In Pocket

#080-000-721AQ SPD Tool, 1B42N86 � � � � � � � � � � � � � � � $ 49.99

SIGHT BASE CUTTERSCUSTOM MADE DOVETAIL END MILLS IN BOTH PREMIUM CARBIDE AND HIGH SPEED STEEL

HIGH SPEED STEEL STANDARD SIGHT BASE CUTTER - 2" (5cm) long. 3/8" (9.5mm) diameter shank. 60° shoulder. DO NOT EX-CEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-359AQ HSS Standard Sight Base Cutter, 8K27D06 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 37.99

CARBIDE STANDARD SIGHT BASE CUTTER - Solid carbide. 2" (5cm) long. 3/8" (9.5mm) diameter shank. 60° shoulder.

#080-621-060AQ Carbide Standard Sight Base Cutter, 8K69G99 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 79.99

SPECIAL FRONT SIGHT DOVETAIL CUTTERSUnique Sizes For Wilson & Meprolight

WILSON SNAG-FREE DOVETAIL CUTTER - Cuts the .290" x 60° dovetail required to install all current models of the Wilson Snag-Free front sights. CAUTION: For use in milling machine only.

HIGH-SPEED STEEL WILSON DOVETAIL CUTTER - 2" (5cm) long. .375" (9.5mm) diameter shaft. 60° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-290AQ Wilson Dovetail Cutter, 8K27P96 � � � $ 36.99

CARBIDE WILSON DOVETAIL CUTTER - Solid carbide 2" (5cm) long. .375" (9.5mm) diameter shaft. 60° shoulder.

#080-621-291AQ Carbide Wilson Dovetail Cutter, 7A55K31 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 79.99

MEPROLIGHT® DOVETAIL CUTTER - Cuts the .250" x 74° dove-tail required when altering ramp-style front sights to accept Mep-rolight’s Universal front sight inserts. Cutter can be used to open up a standard ramp when installing Brownells Colored Sight Inserts. DO NOT EXCEED 700 RPM. HIGHER SPEED WILL BREAK TEETH.

#080-621-250AQ Dovetail Cutter, .250" x 74°, 8K35F88 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 44.99

sights. This is done on purpose to allow for factory variations in base width as well as milling tolerances. CAUTION: For use in milling machine only.

HSS SEMI-AUTO PISTOL SIGHT BASE CUTTER - High speed steel, 2" (5cm) long, 3/8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-331AQ 60° HSS Semi-Auto Sight Base Cutter, 8K29F59 � � � � � � � � � � � � � � � � � � � � $ 36.99

#080-621-330AQ 65° HSS Semi-Auto Sight Base Cutter, 8K23M72 � � � � � � � � � � � � � � � � � � � 31.99

CARBIDE SEMI-AUTO PISTOL SIGHT BASE CUTTER - Solid car-bide cutter resists wear when cutting pistols made from hard-ened steel. 2" (5cm) long, 3/8" (9.5mm) diameter shank. 60° or 65° shoulder.

#080-621-066AQ 60° Carbide Semi-Auto Sight Base Cutter, 7A60B15 � � � � � � � � � � � � � � � � � � � � $ 85.99

#080-621-065AQ 65° Carbide Semi-Auto Sight Base Cutter, 7A69I99 � � � � � � � � � � � � � � � � � � � � 89.99

FRONT SIGHT INSERT CUTTER

60° Shoulder x .245"

We’ve had many requests for a small dovetail cutter that would speed up the cutting of dovetails in front sight blades when installing colored inserts. The one we’ve had made cuts a ¼" wide dovetail, just right for sight inserts, and the finished product is very precise. Since the cutter is small, (it tapers to a diameter of .110"), you must make an initial cut with a 1/8" end mill (listed below). By using the end mill to remove some metal first, you’ll avoid overloading the cutter and breaking it. CAU-TION: For use in milling machine only.

HSS FRONT SIGHT INSERT CUTTER - High speed steel. 21/32" (5.1cm) long. ¼" (6.3cm) diameter shank. Maximum cut depth is .100" (2.5mm) 60° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-245AQ HSS Front Sight Insert Cutter, 8K22C03� � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

CARBIDE SIGHT INSERT CUTTER - Solid carbide 2" (5cm) long. ¼" (6.3cm) diameter shank. 60° shoulder.

#080-621-246AQ Carbide Sight Insert Cutter, 7A50I09 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 71.99

HEINIE REAR SIGHT CUTTER

65° Shoulder x .370"

Cuts the .370 x 65° dovetail required when fitting Heinie rear sights. Solid carbide cuts the hardest slides with minimal wear.

#080-621-371AQ Carbide Heinie Rear Sight Cutter, 7A53A58 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 70.99

STANDARD SIGHT BASE CUTTER

60° Shoulder x .359"

Universal Sight Base Cutter made for sights with 60° shoul-der and a 3/8" base. Cuts most standard front and rear rifle sights as well as 1911 Auto low-mount, adjustable sights like E.E.A. Super Sights, Millett and Bo-Mar-style. Cutter is slightly undersized at .359" which requires that you make two cutting passes to compensate for factory variations in sight manufac-ture and milling tolerances. Designed with proper relief for maximum strength and clean cutting. CAUTION: For use in milling machine only.

LOW MOUNT 1911 AUTO SIGHT BASE CUTTER

65° Shoulder x .495"

These cutters are specially designed by us and made to our specifications for cutting the sight base slot required to mount the Wichita and Novak Lo-Mount 1911 Auto sights. Use ¼" car-bide end mill to remove the bulk of the material (see drawing above) then make final dovetail cut. Final cut to lower rear of slide is done with an end mill and is not a part of the sight base cut. Made slightly undersized to compensate for variations in sight bases and milling tolerances on installation. With the popularity of custom 1911 Auto pistols, this cutter is one that you will use frequently in your custom work. CAUTION: For use in milling machine only. ab

HSS DOVETAIL SIGHT BASE CUTTER - 2" (5cm). .495" diameter cut. ½" (12.7mm) diameter shank. 65° shoulder. DO NOT EX-CEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-495AQ HSS Lo-Mount Sight Base Cutter, 8K41D84 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 52.99

CARBIDE DOVETAIL SIGHT BASE CUTTER - Much harder and longer-lasting than HSS cutter. Use on hardened Colt fac-tory slides. Solid carbide, 2" (5cm) long. .495" diameter cut. ½" (12.7mm) diameter shank. 65° shoulder.

#080-621-965AQ Carbide Lo-Mount Sight Base Cutter, 9K89P99 � � � � � � � � � � � � � � � � � � $ 114.99

FRONT SIGHT DOVETAIL CUTTER

60° & 65° Shoulder x .300"

Cuts lengthwise dovetail required to install special hand-gun front sights from Jim Clark, Ed Brown, Bob Marvel and others. Slightly undersized to allow for precise final fitting and to compensate for any machine wear. CAUTION: For use in mill-ing machine only.

HSS FRONT SIGHT DOVETAIL CUTTER - High speed steel. .300" (7.3mm) diameter cut, 3/8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.

#080-621-300AQ 60° HSS Front Sight Dovetail Cutter, 8K32B13 � � � � � � � � � � � � � � � � � � � � $ 44.99

#080-621-305AQ 65° HSS Front Sight Dovetail Cutter, 8K28H41 � � � � � � � � � � � � � � � � � � � 36.99

CARBIDE FRONT SIGHT DOVETAIL CUTTER - Solid carbide re-sists wear and easily cuts through even hardened steels. .300" (7.3mm) dia. cut, 3/8" (9.5mm) dia. shank. 60° or 65° shoulder.

#080-621-960AQ 60° Carbide Front Sight Dovetail Cutter, 7A58B97 � � � � � � � � � � � � � � � � � � � � $ 77.99

#080-621-963AQ 65° Carbide Front Sight Dovetail Cutter, 7A57I69 � � � � � � � � � � � � � � � � � � � � 80.99

SEMI-AUTO PISTOL SIGHT BASE CUTTER

60° & 65° Shoulder x .330"

Our special 65° shoulder Sight Base Cutter designed to cut dovetails for both standard Colt factory and mil-spec 1911 Au-tos, and for replacement sights like Wichita Hi-Mount, older Bo- Mar and others with a 65° shoulder. Some makers use a 60° dovetail on their rear sights and we also have a cutter to match them. For low-mount adjustable sights use the Standard Sight Base Cutter shown on this page. Actual cutting diameter is .330" so more than one pass will be required to install most

We’ve taken our most popular dovetail cutters and cryo-genically treated them to give you a tool that will cut the tough-est material and last longer, saving down-time and increasing your production. Our cryo-treated tools have been deep-treat-ed to -320°F to change the molecular structure of the metal alloy, making them denser and removing the stresses that lead to tool fatigue. Cryo-treated tools do not look different than untreated tools, so we’ve added two rings near the working end to differentiate them from our regular cutters. abSPECS: Cryo-treated, high-speed steel.

CRYO-TREATED DOVETAIL CUTTERLonger Cutting Life;

Reduces Replacement Costs

STOCK # SIZE PRICE#080-000-271AQ 60° x .245" 8K29C46 $ 39.97#080-000-272AQ 74° x .250" 8K43A04 $ 59.25#080-000-273AQ 60° x .290" 8K32E60 $ 41.46#080-000-274AQ 60° x .300" 8K40L43 $ 54.46#080-000-275AQ 65° x .330" 8K31L56 $ 41.50#080-000-276AQ 60° x .330" 8K38H34 $ 46.99#080-000-277AQ 60° x .359" 8K34M90 $ 45.99#080-000-278AQ 65° x .490" 8K39G43 $ 52.99#080-000-279AQ 65° x .300" 8K36C88 $ 45.99

PAGE 518 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

60°- STANDARD SLOTSpecially manufactured, true parallel, 3-square file with

only one side cutting - other two sides “safe”. This means the file can be used to widen dovetail slots in gun barrels without danger of deepening the slot or damaging the edge not being worked on. Being a true parallel file, you have absolute control over the angle of the dovetail - impossible with other type files. SPECS: 7" (17.8cm) long. .284" (7.2mm) wide. #1, medium, doublecut. #2, fine, single-cut.

#080-648-160AQ #1 60° Sight Base File, 6C39I99 � � � � � $ 49.99#080-648-060AQ #2 60° Sight Base File, 8K38D95 � � � � 46.99

65°- 1911 AUTO-TYPE SLOTDesigned especially for widening and final fitting after us-

ing our 65° Sight Base Cutter to cut the basic slot. Or, can open up a 60° slot to proper 65° angle if changing to a new sight design. Has true parallel cutting edges for precision filing, giv-ing you full control over the angle of the dovetail. One cutting side only, with the other two sides “safe”, so you can widen or deepen sight slots safely without fear of changing the other dimensions. SPECS: 7" (17.8cm) long. 3/16" (4.8mm) wide. #1, medium, doublecut. #2, fine, single-cut.

#080-648-165AQ #1 65° Sight Base File, 6C30G77 � � � $ 34.99#080-648-265AQ #2 65° Sight Base File, 6C33L86 � � � 39.99

(See Sight Base Cutters listed elsewhere.)

SIGHT BASE FILES

The Professional Way To Safely Widen Or Cut New Dovetails

This hardened steel punch is designed to aid in the removal of the extractor pin and the firing pin posi-tioning pin found in the SIG E2 slides. The half-round

profile gives maximum contact area on the partially exposed ends of the pins and transfers the hammer blow efficiently. A built-in stop limits tool travel to the proper depth to avoid mar-ring the slide. abSPECS: S7 hardened tool steel, black oxide finish. Length – 3½"; tip diame-ter - .118" (3mm), body diameter - .320" (8mm). Fits SIG P226E2 & P229E2.

K & C BARRELS SIG SAUER®

E2 SLIDE DISASSEMBLY TOOLThe Correct Tool For The

New E2 Slides

#100-009-923AQ Sig Sauer E2 Slide Tool, 5B16I29 � � � � $ 19.99

Compact, two-in-one specialty tool re-moves the firing pin spring pin, plus the hammer mainsprings on your P250 pistol. Features an elliptical tip for pushing on the firing pin spring pin without flattening the head, plus a con-cave tip for the safe, controlled removal of the hammer double mainsprings. Precision machined from steel bar stock, then hardened to Rc 52 for added strength. Small enough to fit in your pocket, range bag, or armorer’s kit. abSPECS: Steel, Rc 52 hardness. 31/2" (9.5cm) long x 5/16" (8mm) diameter handle.

K & C BARRELS SIG SAUER P250

ASSEMBLY & DISASSEMBLY TOOLRemoves Firing Pin

Spring Pin & Hammer Mainsprings

#100-004-424AQ Assembly & Disassembly Tool, 5B15J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 19.99

Handy tool slides between the extractor and frame to easily lift out the extractor on your XD/

XDM pistol. Tool is ideal when you need to replace a broken extractor or want to give your pistol a thorough cleaning. abSPECS: Steel.

PISTOLGEAR SPRINGFIELD XD/XDM

EXTRACTOR REMOVAL TOOLMakes Removing The

Extractor Quick & Easy

#100-015-784AQ Extractor Removal Tool, 4G00GRK � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 11.95

Precision CNC machined tool safely removes, installs and adjusts fragile Tritium, front and rear night sights on H&K USP and P2000 pistols. Easy-to-use, just place your pistol slide in the tool, making sure the sight dovetail lines-up with the sight pusher, then turn the adjustment knob to clamp the slide in place. Turn the easy-to-grasp, hardened steel T-handle to slowly press the pusher tip against the sight and gently push the sight into the dovetail. Self-lubricating, oil-impregnated Oilite® bronze bearings and extra-fine threads help ensure smooth, precise sight adjust-ment. Specifically designed for use with fixed, front and rear,

AMERIGLO H&K USP/P2000

SIGHT ADJUSTMENT TOOLRemoves, Installs & Adjusts

Dovetail Sights Without Damage

#100-004-195AQ Sight Adjustment Tool, 4K121B43 $ 133.99

Handy kit has ev-erything you need to professionally install,

remove, or adjust sights on Glock pistols – including a set of Trijicon night sights for your first job. The hefty, gunsmith-grade MGW Rear Sight Mover tool works on any Glock pistol with angle-sided rear sights. The B&J Machine combination tool is one of the best we’ve found for working on Glock front sights. The kit’s Trijicon Bright & Tough™ front/rear night sights fit any 9mm/.40 S&W Glock and give your pistol a clas-sic 3-dot sight picture that’s visible in all lighting conditions. abSPECS: MGW Rear Sight Mover – aluminum and steel construction. B&J Tool – Delrin® handle, steel punch and wrench. Sights – Steel, blued with tritium inserts. Fits Glock 17/17L/19/22/23/24/26/27/33/34/35 pistols with fixed sights.

SIGHT INSTALLATION STARTER KIT for GLOCK®

Gunsmith Tools To Work On Glock Sights – Plus A Set

Of Night Sights

#080-000-935AQ Sight Installation Starter Kit for Glock, 8K205Q86 � � � � � � � � � � � � � � � � � $ 219.99

Universal sight installation tool allows you to change or adjust iron sights on a variety of pistols. Tool has two primary components: the upper carriage which includes the pusher assembly, and the lower slide support assembly. Carriage fea-tures a Delrin® pad set exactly .015" above the slide, removing any guess work about how high to set pusher assembly. Pad is adjustable for pistols which have a raised sight platform. Four slide support pads, two top clamping bolts and four side bolts ensure the slide is secure and straight. Tool comes with straight sided pusher assembly which fits most pistols. Durable tool will withstand years of use. Features machined notches for vice mounting or can be used as a hand tool. Tool comes with instructional DVD. Interchangeable Slide Shoe Clamps are fire-arm specific, giving you a wide range of versatility to the pistols you work on. Shoes are made from low carbon steel with a black oxide finish, and are sold separately below. For Glock and HK pistols use the 30 Degree Block Assembly which features bev-eled sides the bar. Assembly easily replaces sight mover which comes with the tool and works identical. Square Block Assembly - Replacement for a worn or damaged square block that comes with the the Sight Pro Tool. ab

MGW

SIGHT PRO TOOL

One Tool Lets You Install Sights On A Variety Of Pistols

Main Sight Tool

#584-000-005AQ Sight Pro Tool, 4H312H00 � � � � � � � � $ 329.99#584-000-006AQ 30 Degree Block Assembly,

4H71G00 � � � � � � � � � � � � � � � � � � � � � � � � � 74.99#584-000-016AQ Beretta 92 Slide Shoe, 4H17M00 � � 17.99#584-000-017AQ Beretta Cougar/PX4 Slide Shoe,

4H17K00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-036AQ Bersa BP Series Slide Shoe,

4H17M00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99#584-000-010AQ Colt 1911 Slide Shoe, 4H17K00 � � � � 17.99 584-000-029AQ Browning Hi-Power Slide Shoe,

4H17D00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-023AQ Colt Mustang .380 Slide Shoe,

4H17K00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-026AQ CZ-75 Slide Shoe, 4H17H00 � � � � � � 17.99#584-000-013AQ FN FNP/FNS/FNX/Forty-Nine

9mm/.40 Slide Shoe, 4H17C00 � � � 17.99 584-000-034AQ FN .45 ACP Pistol Slide Shoe,

4H17G00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99#584-000-007AQ Glock Slide Shoe, (Except Glock

42) , 4H17F00 � � � � � � � � � � � � � � � � � � � � 17.99 584-000-020AQ Glock 42 Slide Shoe, 4H17K00 � � � � 17.99 584-000-035AQ Kahr P40/C240/PM9 Slide Shoe,

4H17M00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-024AQ Ruger LC Series Slide Shoe,

4H17L00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-038AQ Kimber Solo Carry Slide Shoe,

4H17E00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-025AQ Ruger P-Series Slide Shoe,

4H17E00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-022AQ Ruger SR Series Slide Shoe,

4H17G00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99#584-000-014AQ Sig P220/225/239/226/228/229

Slide Shoe, 4H17Q00 � � � � � � � � � � � � � 17.99 584-000-027AQ Sig P238 Slide Shoe, 4H17D00 � � � � 17.99 584-000-040AQ Sig P320 Slide Shoe, 4H17I00 � � � � � 17.99 584-000-028AQ Sig P938 Slide Shoe, 4H17K00 � � � � 17.99#584-000-015AQ Sig Pro Series Slide Shoe,

4H17B00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99

Slide Shoe Clamp

30 Degree Block Assembly

Safely moves fixed sights right or left in their dovetails without deforming slide or sight. Specifically designed for use with factory and aftermarket Tritium night sights, which are too fragile for the traditional hammer-and-punch sight installation method; works equally well with iron sights. Thumbscrew securely

locks the slide so it's fully supported in the rigid, machined aluminum body. Separate slots in the screw mechanism en-gage the sight and firmly, yet gently, concentrate screw force to loosen sights from even extremely tight dovetails. Hardened steel handle provides plenty of leverage, while self-lubricating, oil-impregnated Oilite® bronze bearings and extra-fine threads ensure smooth, precise movement. Beretta/Glock models fit rear sights only. Glock Flat-Side fits aftermarket rear sights with straight, non-sloped sides for standard- and large-frame Glock pistols. Glock 42 Adapter required to adjust sights of the G42 pistol in either Glock Sight Mover. SIG fits rear sights on all SIGs except SIG-PRO. Smith & Wesson M&P fits both front and rear sights; will not fit Pro models with 5" barrel. Springfield XD fits both front and rear sights on all XD models except front sight on 5" barrel Tactical model. abSPECS: Aluminum body, anodized. Steel cross carriage bolt and thumb-screw, black oxide finish. Approx. 43/4" (12.1cm) wide x 3" (7.6cm) high x 1" (2.5cm) thick. Exact size varies from model to model.

MGW SEMI-AUTO

SIGHT MOVERAdjusts, Removes & Installs

Sights Without Damage

#584-045-092AQ Beretta 92 Sight Mover, 4H91D43 $ 116.99#584-045-093AQ Beretta 8000/Cougar Sight

Mover, 4H91D43 � � � � � � � � � � � � � � � � � 116.99#584-045-017AQ Glock Sight Mover, 4H95J00 � � � � � 99.99#584-000-004AQ Glock Flat-Side Sight Mover,

4H91M43 � � � � � � � � � � � � � � � � � � � � � � � � � 116.99 584-045-042AQ Glock 42 Adapter, 4H24C30 � � � � � � 28.99#584-045-220AQ SIG Sight Mover, 4H110L00 � � � � � � 129.99#584-000-003AQ S&W M&P Sight Mover,

4H115P50 � � � � � � � � � � � � � � � � � � � � � � � � � 124.99 584-045-002AQ S&W M&P Shield Sight Mover,

4H110Q99 � � � � � � � � � � � � � � � � � � � � � � � � 124.99#584-000-002AQ Springfield XD Sight Mover,

4H112N86 � � � � � � � � � � � � � � � � � � � � � � � � 139.99

Shoes

#584-000-012AQ S&W 3rd Gen 9mm Slide Shoe, 4H17F00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99

584-000-032AQ S&W 3rd Gen .45 ACP Slide Shoe, 4H17K00 � � � � � � � � � � � � � � � � � � � � � � � � � � 17.99

#584-000-019AQ S&W M&P Slide Shoe (all except Shield), 4H17E00 � � � � � � � � � � � � � � � � � 17.99

#584-000-009AQ S&W M&P Shield Slide Shoe , 4H17A00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99

584-000-030AQ S&W .380 Bodyguard Slide Shoe, 4H17M00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99

584-000-031AQ S&W Sigma Slide Shoe, 4H17B00 � 17.99#584-000-011AQ Springfield XD Slide Shoe (Not for

XD-S), 4H17H00 � � � � � � � � � � � � � � � � � � 17.99#584-000-008AQ Springfield XD-S Slide Shoe,

4H17Q00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-037AQ Steyer M40/MPS/M9-A1 Slide

Shoe, 4H17I00� � � � � � � � � � � � � � � � � � � � 17.99#584-000-018AQ USP/P2000/P45 Slide Shoe,

4H17M00 � � � � � � � � � � � � � � � � � � � � � � � � � 17.99 584-000-039AQ Walther P99 Slide Shoe, 4H17M00 17.99 584-000-033AQ Replacement Square Block

Assembly, 4H64F29 � � � � � � � � � � � � � � 67.99

dovetailed Tritium night sights. abSPECS: 6061 T6 Aluminum, anodized, red. Steel lead screw and adjust-ment knob, black matte finish. Body - 43/4" (21cm) long x 15/8" (1.9cm) wide. Fits factory and aftermarket, fixed front and rear sights on all full size & compact HK USP and P2000 pistols.

PAGE 519Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

Universal bench tool pro-vides accurate cross-dovetail pistol sight adjustment and installation without damage to the sight or the slide. Multi-position, slide support block and separate slide clamp adjust quickly. Body is machined from a solid block of aluminum al-loy. Square thread adjustment screw provides plenty of lever-age to move even the most stubborn sight without damage. Includes attachment ears for bench mounting.SPECS: Body - Aluminum, black, hardcoat anodized finish. 6" (15cm) wide, 41/2" (11cm) high, 2 lb. (.9kg) wt. Adjustment Screw - Hardened steel. In-cludes complete instructions and pistol sight reference chart. Will not install tenon-style front sights.

MEPROLIGHT®

UNIVERSAL SIGHT INSTALLATION TOOL

Adjust & Install Over Forty Different Semi-Auto

Pistol Sights

#387-100-000AQ Type II Univ. Sight Tool, 2B679D99 � � � � � � � � � � � � � � � � � � � � � � � � $ 679.99

Specifically designed to in-stall, adjust and remove all mod-els of Trijicon Glock Sights with-out damage. Includes heavy-duty rear sight mover with oilite bushings that allow for very fine

windage adjustments, and a front sight nut driver that fits all models of aftermarket front sights. abSPECS: Aluminum, anodized finish. 3/16" nut driver.

TRIJICON®

SIGHT INSTALLATION TOOL for GLOCK®

Install, Adjust & Remove Glock Sights Without Damage

#892-103-102AQ Trijicon Sight Tool for Glock, 2H139J99 � � � � � � � � � � � � � � � � � � � � � � � � � $ 139.99

Precision-machined, steel tool safely removes, in-stalls and adjusts front and rear sights on handguns. Clamp your slide into the tool and line up the sights with the tool’s pusher tip for installation, removal, or adjustment. Mobile jaw customizes to the height of your slide and can be used from the right or left side. Delrin® liner protects slide from scratches. Includes three sight pushers that attach to the end of the sight-pushing bolt. 1/4" square tip works perfectly on shallow, cross-dovetail sights. Hold Down Clamp helps prevent the slide from twisting in the frame of the P500 by applying extra force to the top of the slide. Provides a secure seat in the tool when working with hard-to-remove sights or slides with angled sides, like the Springfield Armory XD and the S&W M&P. Slide Stop speeds up the process of performing the same sight job on a large number of the same model pistol. Stop simply screws to the P500 frame and lets you position each slide in exactly the same place to per-form the necessary sight adjustment quickly and easily. P500 Universal Sight Tool Kit combines P500 Universal Sight Tool with the Hold Down Clamp and Slide Stop to provide the ulti-mate of flexibility and versatility in a sight adjustment tool. abSPECS: Steel, black, powder-coat finish. Approximately 5" (12.5cm) long, 2" (5cm) wide, 1" (2.54cm) high. Instructions included. Hold Down Clamp – Steel, powder-coated, black. Approximately 4" (10cm) long, 1½" (3.8cm) wide, 3¾" (9.5cm) high). Comes with clamp assembly, jaw screw, 3/32" hex wrench, and instructions. Slide Stop - 1018 steel, black oxide finish. Ap-proximately 1¼" (3.2cm) long, ½" (1.3cm) wide, 1" (2.5cm) high. Includes stop block, stop pin, hex wrench, (5) 6-32 setscrews, and instructions. P500 Universal Sight Tool Kit contains the P500 Universal Sight Tool, Hold Down Clamp, Slide Stop, and complete instructions.

B&J MACHINE

P500 UNIVERSAL SIGHT TOOLSafely Removes & Installs

Dovetail Front & Rear Sights; Works On Shallow,

Cross-Dovetails

#694-000-001AQ P500 Sight Removal Tool, 4F126B64 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 139.99

#694-000-003AQ Hold Down Clamp, 4F62D07 � � � � � � 64.99#694-000-002AQ Slide Stop, 4F20J69 � � � � � � � � � � � � � � � 24.99#694-000-004AQ P500 Universal Sight Tool Kit,

4F211F00 � � � � � � � � � � � � � � � � � � � � � � � � � � 215.99

The P500 Pro builds on the original P500 sight pusher by incorporating a hold down clamp and slide positioning stop into the design and us-ing redesigned pushers to minimize flex and increase the strength of the tool. The pusher and hold down mech-anisms are fully adjustable and can be positioned to accommodate almost any slide se-curely for delicate sight installations. The built-in positioning stop allows the same slide to be removed and quickly replaced while maintaining proper alignment as many times as needed to adjust the sight - an especially handy feature for LE qualifi-cations or any time multiple pistols of the same model require sight work. The tool is made from steel for strength and features polymer clamping surfaces to protect the gun’s finish. abSPECS: Steel, black finish. Approximately 5½" (13.97cm) long, 4" (10.2cm) wide, 3½" (8.9cm) high.

B&J MACHINE

P500 PRO UNIVERSAL SIGHT TOOL

Improved Tool For Installing & Removing Auto

Pistol Sights

#694-000-005AQ P500 Pro Sight Tool, 4F269J99 � � � � � � � � � � � � � � � � � � � � � � � $ 274.99

Designed for installing or removing the hex nut on Glock front sights, this nickel-plated, steel driver also fits S&W Sigma, Walther, and other brands with a 3/16" hex sight nut. Compact size (only 1.6" long) fits easily in a small tool kit, range bag, or your pocket. Knurled top gives you a positive grip for popping loose tight sight screws. ab

FRONT SIGHT TOOL for GLOCK®

Easily Pops Loose Tight Front Sight Hex Screws

#080-001-092AQ Glock Front Sight Tool , 8K5P00 � � � � � $ 7.99

Fits the small, hex head screw that holds Glock sights in place. Makes installing re-placement sights or removing sights for maintenance easier

with less chance of damage. Hex shank fits Magna-Tip® screw-drivers. Not for use with 6" slides. All-steel construction. ab

ED BROWN

FRONT SIGHT TOOL for GLOCK®Easily Removes/Installs

Glock Front Sights

#087-017-001AQ Glock Front Sight Tool, 7H16A51 � $ 19.95

Here it is! A tool kit designed specifically for the armorer, gunsmith, shop, or department servicing Smith and Wesson Revolvers. You get everything needed

to perform virtually any internal repair or rebuilding chore on the innumer-able Smiths found in police departments and law enforcement agencies

throughout the U.S. and the world. To put together this kit, filled with many one-of-a-kind tools, we drew on the knowledge of many good friends (to whom we are forever indebted) who work on these guns every day. Special Thanks to Gene Thompson, Brunswick, Georgia who not only pushed us hard to put the kit together but also lent us many of his personal tools to use as patterns. What you get is a 41-piece kit of first quality, professional tools to help you service Smiths faster, more efficiently and without the errors often caused by “pick-up” or “make-do” equipment. Although designed primarily for the “K” frame, many of the tools work on other Smith frame sizes and other makes of revolvers too. ab

#080-720-038AQ .38/.357 Ext. Spport Tool, 8K22Q33 � $ 29.99

⑮ ARMORER’S BRUSH - Perfect for dusting recesses.#821-135-210AQ Armorer’s Brush, 8K7J00 � � � � � � � � � $ 8.99

⑯ BROWNELLS ASSEMBLY/DISASSEMBLY MAT - Provides no-slip, no-scratch work surface anywhere.

#358-128-316AQ Assy/Disassy Mat, 8E18Q99 � � � � � � $ 22.99

⑰ HAND & CYLINDER STOP WINDOW FILES - Correct offset shapes and sizes to alter these openings for new parts.

#080-754-000AQ Hand Window File, 6C29J08 � � � � � $ 36.99#360-318-731AQ Cylinder Stop Window File,

6C30B99 � � � � � � � � � � � � � � � � � � � � � � � � � 30.99

⑱ #455 CENTER PUNCH - Swages hammer nose rivet.#587-113-455AQ Center Punch 455, 7H4B55 � � � � � � � $ 4.55

⑲ GUN/PARTS CLEANING BRUSH#676-450-001AQ Gun/Parts Brush, each, 8K1Q28 � � $ 3.99

⑳ BROWNELLS REBOUND SLIDE SPRING TOOL - Clears the frame and compresses the rebound spring.

#080-666-000AQ Rebound Slide Tool, 3K14N68 � � � � $ 19.99

◯21 LAW ENFORCEMENT MAGNA-TIP® S&W SCREWDRIVER COMBO - Clip-tip handle with three bits for S&W screws.

#080-088-003AQ S&W Screwdriver Set, 8K14I32 � � � � $ 16.99

◯22 60/68 HEADSPACE GAUGE - Fast and accurate check.#080-633-668AQ 60/68 Cylinder Gauge, 8K27F50 � � $ 35.99

◯23 38 BARREL ALIGNMENT GAUGE - Checks alignment of bore centerline and firing pin hole.

#080-722-300AQ .38 Barrel Alignment Gauge, 8K20H85 � � � � � � � � � � � � � � � � � � � � � � � � � $ 24.99

◯24 #90 PIN VISE - Double-ended to fit pins up to .125".#345-090-000AQ Pin Vise No. 90, 5D15C49 � � � � � � � � � $ 15.49

◯25 CRANE STRETCHER - Cures excess cylinder movement.#080-640-000AQ Crane Stretcher, 8K26L03 � � � � � � � � $ 35.99

◯26 950-252 FEELER GAUGE - Checks barrel/cylinder gap.#606-950-252AQ Inch Feeler Gauge, 8K27H99 � � � � � $ 27.99

◯27 REVOLVER FITTERS BENCH BLOCK - Two holes, one slot provide solid surface for driving pins, polishing.

#080-631-000AQ Bench Block, 8K42E28 � � � � � � � � � � � $ 55.99

ARMORER’S KIT BOX - With distinctive Armorer’s Kit label.

#080-200-303AQ Armorer’s Kit Box, 8K10J78 � � � � � � $ 15.99

① MEDIUM INDIA STONE - Removes burrs and roughness.#657-246-146AQ MF-46 India Stone, 7E9M75 � � � � � � � � $ 10.99

② BROWNELLS YOKE/CRANE ALIGNMENT TOOLS - Shows any misalignment due to a bent yoke.

#080-616-001AQ #1 Yoke/Crane Tool, 8K27M28 � � � � � $ 34.99#080-616-002AQ #2 Yoke/Crane Tool, 8K42M98 � � � � � 56.99

③ BROWNELLS YOKE/CRANE REAMER - Removes burrs and restore I.D. after swaging or “stretching”.

#080-627-000AQ Yoke/Crane Reamer, 8K28K27 � � � � � � $ 34.99

④ BROWNELLS NYLON WEDGE - Bends the yoke to restore proper alignment, adds “arch” to mainspring to lighten trigger.

#080-722-100AQ Nylon Wedge, 8K11N81 � � � � � � � � � � � � � $ 14.99

⑤ BARRETTE FILE - For smoothing, fitting.#191-350-370AQ 4" Barrette #1 Cut, 6C20H62 � � � � � � � $ 23.99

⑥ BROWNELLS CUP TIP PUNCHES - Fit round head S&W pins to prevent pin flattening. Six sizes included.

#080-620-306AQ Cup Tip Punch Set C, 8K76E05 � � � � � $ 89.99

⑦ BROWNELLS BRASS DRIFT PUNCH#080-475-300AQ Brass Drift Punch, 8K4B80 � � � � � � � � � � $ 7.99

⑧ BROWNELLS MAGNETIC PIN STARTERS - Hold the round head Smith pins securely for no-slip, no-scratch reassembly.

#080-242-057AQ Small Pin Starter, 3K10H80 � � � � � � � � � $ 16.84#080-242-070AQ Medium Pin Starter, 8K8K66 � � � � � � � 13.99

⑨ BROWNELLS S&W HAND PIN HOLDER#080-722-200AQ S&W Hand Pin Holder, 8K8P00� � � � � � $ 9.99

⑩ BROWNELLS BABBITT BARS - Give cushioned “hammer” blow for loosening side plate, correcting alignment.

#084-172-001AQ Round Babbitt Bar, 4H17B00 � � � � � � � $ 19.99#084-172-002AQ Trapazoid Babbitt Bar, 8K21M60 � � � 31.99

⑪ BROWNELLS .38 SERVICE RANGE ROD - Accurate check of each cylinder chamber’s alignment to axis of the bore.

#080-617-038AQ .38 Service Range Rod, 8K29G30 � � � $ 39.99

⑫ BROWNELLS 82° COUNTERBORE - For deburring/ cham-fering of larger holes than the broaches can handle

#080-722-820AQ 82° Counterbore, 8K16C76 � � � � � � � � � $ 19.99

⑬BALLPEEN HAMMER#956-000-002AQ 4 oz. Ballpeen Hammer, 9D29Q98 � � $ 29.99

⑭ BROWNELLS EXTRACTOR SUPPORT - Takes load off ex-tractor, ejector star, and guide pin during ejector rod removal.

TOOLS FOR SMITH & WESSON REVOLVERS41 Tools - And More - Specifically For Servicing Smith & Wessons

135

4

8

3

2

1

7

9

6

1410

15

11

12

18

16

17

19

20

21

22

23

2425

26

27

10

11

17

#080-722-010AQ Armorer’s Service Kit, All Tools Plus Box, 8K500F99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 580.99#080-722-002AQ Armorer’s Kit Tools, only, 8K489N99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 569.99

TOOLS INCLUDED IN S&W TOOL KIT

PAGE 520 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

HA

ND

GU

N T

OO

LS

Takes the guesswork out of determining how wide to mill the dovetail cut. Lets you make fast, finished cuts within .0005". Mea-sures sights and dovetails. abSPECS: Aluminum base, matte black finish. Steel pins. Base 2" (5.8cm) x 2"

(5.8cm) x 1.1" (2.8cm). Includes charts, instructions.

XS SIGHT SYSTEMS

DOVETAIL MEASURING TOOLDetermines Sight &

Dovetail Width

#006-101-000AQ Dovetail Measuring Tool, 6K39J29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 45.00

Pocket tool helps you perform most of the tasks re-quired to maintain a Smith & Wesson K, L, or N frame re-volver. Great for quick repairs and adjustments in the field or at the range. Includes screw-driver bits for the grip screws and strain screws, plus the screws for the side plate, yoke, cylinder thumb piece latch nut, and adjustable rear sight. Use it to remove/ install the rebound slide and rebound slide spring, as well as to tighten/loosen the ex-tractor rod without damaging the knurling on the tip of the rod. Strong internal magnets retain the driver bits and help keep small steel parts from rolling away during field or bench disas-sembly. Driver bits are hollow ground to ensure full-surface contact with the screw slots. abSPECS: 6061 T6 aluminum body, hardcoat anodized, matte black, with hardened steel 210-2 and 150-3 bits. 31/4" (8.2cm) long, 3/4" (1.9cm) wide, 1/2" (1.3cm) thick. 2 oz. (57g) wt. For Smith & Wesson K, L, and N frame revolvers.

S&W K/L/N FRAME SPD TOOLBasic Maintenance Tool Kit

That Fits In Your Pocket

#080-000-820AQ S&W Revolver SPD Tool, 1B42A86 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 49.99

Our Revolver Action Wrench completely sur-

rounds and supports the frame with special no-mar alumi-num heads to prevent twisting and gouging. Heads fit exist-ing Brownells Action Wrench System handle or start with the complete unit shown here and then add other handgun and rifle heads as needed. abSPECS: Base/Handle Unit - Steel, blued. 123/4" (31cm) long, 1" (2.5cm) diameter handle. Interchangeable Heads - Aluminum 3/4" (19mm) square, 51/5" (14cm) long. Complete Wrench - Includes Base/Handle and heads for one gun model, bolts and instructions. Complete Wrench or Heads Only to fit double action revolvers.

SINGLE ACTION, ACTION WRENCHES - Aluminum heads com-pletely enclose those fragile frames to help eliminate damage.SPECS: Base/Handle Unit - Steel, blue. 123/4" (31cm) long, 1" (2.5cm) di-ameter handle. Interchangeable Heads - Aluminum, 3/4" (19mm) square, 51/8" (14cm) long. Complete Wrench - Includes Base/Handle and heads for one gun model, bolts and instructions. Ruger fits Blackhawk®, Super Blackhawk® and Vaquero® size frames.

STK# COMPLETE WRENCH STK# HEADS ONLY FITS

#080-800-173AQ #080-801-073AQ Colt SAA#080-800-174AQ #080-801-074AQ Ruger

— Advise # — Complete Wrench, 8K101A26 � � � � � � � $ 139.99— Advise # — Heads, only, 8K74B75 � � � � � � � � � � � � � � � 114.99

REVOLVER ACTION WRENCHCompletely Surrounds

Revolver Frames To Prevent

Expensive Torque Damage

STK# COMPLETE WRENCH STK# HEADS ONLY FITS

#080-850-002AQ #080-851-002AQ S&W K Frame#080-850-003AQ #080-851-003AQ S&W L Frame#080-850-004AQ #080-851-004AQ S&W N Frame

— Advise # — D/A Revolver Wrench, 8K101L50 � � � � $ 139.99— Advise # — D/A Revolver Wrench Heads, only,

8K70P43 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 106.99

Prevents springing the frame by using fitted inserts that exactly match the contours of the revolver frame and distribute the turning forces evenly over it. abSPECS: Steel handle, aluminum head, Del-rin® insert. 151/4" (39cm) overall length. 3" (7.6cm) wide 41/2" (11.4cm) includes lock screw). 1" (2.5cm) thick. .755" (19.2mm) handle diameter. Weighs 13/4 lb. (794 g) w/o

insert. Inserts weigh 61/2 oz. (184.3g).

MGW, LTD.

CONTOUR FITTED REVOLVER FRAME WRENCH

Professional Tool Prevents Springing Frame

STK# WRENCH W/1 INSERT

STK# FRAME INSERT ONLY

MODEL

#584-200-002AQ #584-100-002AQ Colt Python & Officers’ Mod.t#584-200-003AQ #584-100-003AQ S&W “L”#584-200-004AQ #584-100-004AQ S&W “K”#584-200-005AQ #584-100-005AQ S&W “N”#584-200-006AQ #584-100-006AQ Ruger Blackhawk®/Colt SAA

— Advise # — Wrench w/1 Insert, 4H109E35 � � � � � � $ 147.57— Advise # — Frame Insert Only, 4H28C36� � � � � � � � 38.27

Heavy-duty, high-le-verage, wrench and Del-rin® blocks give form-fit-ted support of the frame for barrel removal and other customizing jobs. Frame Blocks fit around the entire frame to provide maximum support for changing the barrel or custom machining opera-tions like opening up the rear sight notch, making dovetails, or disassembling internal parts. Insert Blocks fit on the front of the frame and are used only for barrel removal/installation and tightening or loosening the barrel to regulate sights. Non-marring, aluminum Barrel Blocks convert the wrench handle into a barrel wrench. Use two handles, one with frame blocks, one with barrel blocks to remove barrel from frame without a vise. Blocks alone work great as vise jaws. abSPECS: Handle - Steel. 14"(35.6cm) long, 1" (2.5cm) wide, 1" high. Includes Allen wrenches. Frame Blocks - Delrin, black. 31/8"(7.9cm) long, 3/4" (1.9cm) wide, 27/16" (6.2cm) high. Ruger SA fits all Ruger single action frames. Colt SAA fits Colt Single Action Army and clones. Insert Blocks – Delrin, black.

POWER CUSTOM

REVOLVER FRAME/BARREL WRENCHSeparate Barrels &

Frames; A Third Hand For Most

Disassembly Jobs

#713-000-024AQ Frame/Bbl Wrench Handle, 3A81F77 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 89.99

#713-000-025AQ Ruger SA Frame Blocks, 3A95N28 � � � � � � � � � � � � � � � � � � � � � � � � � � � 99.99

#713-000-026AQ Colt SAA Frame Blocks, 3A95E28 � � � 99.99#713-000-086AQ S&W K/L Insert Blocks, 3A41I67 � � � � 49.99#713-000-087AQ S&W N Insert Blocks, 3A41K67 � � � � � 49.99#713-000-088AQ CSA/RSA Insert Blocks, 3A41G67 � � � 49.99#713-000-027AQ Uni. SA Barrel Blocks, 3A32A67 � � � � � 36.99

Robust tool gives you enough length and lever-age to remove even the most stubborn pins without mar-ring the frame. Double-end-

ed tool precisely fits Ruger revolvers on one end and Colts on the other, so base pins on the most popular cowboy guns can be pulled with one convenient tool. abSPECS: Steel, black. 5" (12.5cm) long. Fits Ruger and Colt revolver base pins.

SA REVOLVER

DOUBLE-END BASE PIN PULLERPops Loose Stuck Base Pins On Ruger® & Colt Revolvers

#080-000-367AQ Double End Base Pin Puller, 8K21C95 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

Hardened steel bar hooks into the groove in the head of the base pin to gently pull pins out of the frame without mark-ing pin or frame. Fits Colt, and some clone, factory pins. abSPECS: Steel, blue finish. 31/2" (8.9cm) long.

RIMFIRE GUN WORKS SA REVOLVER

BASE PIN PULLERGently Pop Base Pins Loose

#777-000-001AQ Colt Base Pin Puller, 7G19N50 � � � � � $ 22.99#777-000-002AQ Base Pin Puller for Ruger SA,

7G19H50 � � � � � � � � � � � � � � � � � � � � � � � � � � 22.99

Don’t let a stuck bullet from a “squib” or weak load cut short a shooting session. Far superior to other rods or make-shift punches, this non-marring brass rod fits the bore close-ly, can’t wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto, or adapt to, a Dewey or other cleaning rod; very handy for knocking stuck bullets out of rifle barrels. abSPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey rod adapters.

SQUIB ROD

No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores

#084-175-000AQ Squib Rod Kit, 4H64K56 � � � � � � � � � � � � $ 85.99

STOCK # FITS#084-175-032AQ .32 Cal.#084-175-357AQ 9mm/.38/.357Cal.#084-175-040AQ 10mm/.40/.41 Cal.

STOCK # FITS#084-175-044AQ .44 Cal.#084-175-045AQ .45 Cal.

— Advise # — Squib Rod Pak, 4H23N64 � � � � � � � � � � � $ 29.99

Set back new or existing barrels to tighten barrel/cylin-der gap, without a lathe. abSPECS: Fixture includes steel fixture body, 27/8" (7.3cm) long. Adjustable

carbide cutter, one .38/.357 bore pilot, adjustable pilot carrier, and Allen wrench. Master Kit includes all of the above and pilots for, .22RF, .32, .38/.357, .41, .44 and .45.

BARREL SET-BACK FIXTURERelieve Revolver Barrel

Shoulders Without A Lathe

#080-762-380AQ Barrel Set-Back Fixture, 8K118K18 � � � � � � � � � � � � � � � � � � � � � � � � � $ 154.99

#080-762-000AQ Barrel Set-Back Master Kit, 8K179A26 � � � � � � � � � � � � � � � � � � � � � � � � � 257.99

#080-762-001AQ Replacement Cutter, 8K21L79 � � � � 30.99

Because both Ruger and S&W’s lock at the front and rear of the extractor rod, even a slightly bent one can cause diffi-culty in lockup and will impair smooth operation, especially for doubleaction shooting. These tools help precisely align the crane in just minutes, without “guesswork”. Precision ground and hardened to within .0005" on all critical dimensions to as-sure the ultimate in accuracy. Instructions included. Hardened to Rc 52-54. abSPECS: J - 2.6" (6.6cm) long; K - 3.17" (8cm) long; Ruger® - 3.025" (7.6cm) long. #1 for S&W “J” Frame (centerfire only); #2 for S&W “K”, “L” or “N” Frame; #3 for Ruger Speed-Six® and Security-Six®. Shorten knurled end to fit 2-2-1/2" barrel revolvers.

YOKE/CRANE ALIGNMENT TOOL

.0005" Tolerances For Ultimate Accuracy

#080-616-001AQ #1 Yoke/Crane Tool, 8K27M28 � � � � � $ 34.99#080-616-002AQ #2 Yoke/Crane Tool, 8K42M98 � � � � � 56.99#080-616-003AQ #3 Yoke/Crane Tool, 2C23J82 � � � � � � 30.95

Removes all burrs and roughness from inside the Ruger “Six” Series D.A. and S&W K/L/N crane. Also restores crane to proper dimensions after “