making wire springs, part iii
TRANSCRIPT
← Green Mountain Barrels – follow up 1911 Detailed Disassembly →
Making Wire Springs, Part III. Torsion SpringsPosted on April 23, 2011 by GsT
Torsion Springs
The final wire spring to cover is a torsion spring. In its simplest incarnation a torsion
spring is just a stick of music wire with a few twists, usually 2-5, wound on a mandrel,
with the ends left straight. That version is so uninteresting that we’ll proceed directly to
a more interesting incarnation: AR and AK hammer springs. (The AR series rifles also
use a torsion spring for trigger return). This sort of spring is really two torsion springs
with a linkage in between that engages the hammer.
For those that are unfamiliar with such a spring, here is the spring from an AK-47:
Search
Recent PostsMachining an AR-15 upper
receiver forging – part III
Machining an AR-15 upper
receiver forging – part II
Machining AR-15 upper receiver
forgings part I – redux
Machining AR-15 upper forgings
Wednesday Book Review:
Hatcher’s Notebook
Recent CommentsC Fitton on Welcome to
FirearmsDesigner.com,
Introduction
sirrrbosss on Calculating gas port
Firearms Designer Designing, Constructing, and
Gunsmithing of Firearms
Home About
Do you need professional PDFs? Try PDFmyURL!
The hammer / trigger spring from an (Yugoslavian) AK-47
The AK-47 is one of a few designs that have the additional feature of being made from
material which is actually a pair of twisted wires. For our purposes here, we’ll wind a
torsion spring from a single piece of music wire to replace a factory AK spring.
There are three key measurements that we need:
1. The distance from the center of the ‘axle’ or pivot pin, to the area on the hammer
where the spring arm should apply its force.
2. The width (plus a small allowance) of the hammer, and
location for a DI AR-15
Josh Day on About
Gas port location - Practical
Machinist - Largest Manufacturing
Technology Forum on the Web on
Calculating gas port location for a
DI AR-15
Paul on Calculating gas port
location for a DI AR-15
ArchivesApril 2013
March 2013
January 2013
December 2012
January 2012
June 2011
April 2011
March 2011
February 2011
CategoriesBook Review
Firearm Design
Gunsmithing
Notices
Shop work
Uncategorized
Do you need professional PDFs? Try PDFmyURL!
3. The diameter of the bosses on the hammer that the spring windings will rest on.
The first dimension is a direct measurement. The second is the width of the hammer plus
0.01″-0.02″. The final dimension is easily ignored by using a mandrel the diameter of the
bosses on the hammer. By doing so, the spring will ‘unwind’ enough after forming to
ensure a loose enough fit that there is room for it to tighten as the spring is tensioned.
Draft of dimensions taken from an AK-47 hammer
Do you need professional PDFs? Try PDFmyURL!
Making a hammer spring requires special fixturing. In essence the fixture is an axle
(mandrel) of the correct diameter, around which rotates a form, of the desired width,
which holds a bite (the place where the spring material doubles back) at the appropriate
radius. Add to this something to straighten / tension the wire before it is wound, and you
have everything you need.
There are many ways to make a fixture that satisfies these requirements. I’ll make mine
as three units: collars to account for the diameter of the bosses, a form which factors in
the hammer width and bearing surface, and a tool to maintain tension and straighten the
wire as it’s being wound. As an arbitrary choice, I’ll use a 1/4″ axle for the assembly to
work on. It’s worth noting that the easiest way to do this might involve using the
hammer itself as a form and collars with only the addition of a tensioning tool, but a
custom tool will give a little more control.
Start by making the form. The form for this AK replacement spring will be 0.300″ wide
(that’s the width of the AK hammer (0.270″) pluse a 0.030″ allowance. It will trap the
“bite” of the wire at 0.575″ from the center of rotation. The center of rotation will be a
1/4″ hole to fit the axle.
I square up a piece of material that’s close to the correct dimensions, thin it to 0.300″.
At that point I’ll layout two lines – the axis on which the axle hole (1/4″) will be drilled
and the line that must trap the bite 0.575″ away.
Do you need professional PDFs? Try PDFmyURL!
The blank for the form, with the pivot hole center-punched and a line where the bite will be captured.
I’ll then saw a notch to capture the “bite” – the notch must be wide enough to
accommodate the wire I’ll use – extra width won’t hurt. You can double up blades on a
hacksaw to do this, if necessary.
Do you need professional PDFs? Try PDFmyURL!
The notch added to the form.
With the notch cut, I’ll go to the mill or drill press and drill the axle hole – that’s it for
the form.
Do you need professional PDFs? Try PDFmyURL!
The form is ready for use.
Next, I’ll make the collars. I’ll start by drilling some stock 1/4″ for the axle, then turning
it to the diameter of the hammer bosses (0.390″). That done, I’ll part off two pieces 1/2″
long. (The windings should only take up 1/4″ or so, so a great deal of width is not
required).
Do you need professional PDFs? Try PDFmyURL!
Bushings to match the diameter of the hammer where the spring coils sit.
Next a tensioning tool is needed. It needs to capture, and tension, two legs of the spring,
rather than just a tail as in previous spring types. A single screw adjustment ensures that
tension is even over both legs. I made mine from an ‘L’ shaped piece of 3/8″ stock, so I
could mount it in a standard tool holder. A small bar of 1/4″ strap serves as the
tensioning device. Tension may be adjusted by the single 1/4″-20 screw.
Do you need professional PDFs? Try PDFmyURL!
The wire tensioning tool, inserted into a standard quick change toolholder for use in the lathe.
A lathe is not at all necessary to wind a hammer spring, but it’s convenient in this case.
Anything that can hold the tensioner and axle will do. The spring is started by making a
bite in the spring that is the width of the form. The legs are placed through the tensioner
and the bite is placed in the notch on the form. The collars are held in place by whatever
means are expedient. (My means look especially improvised – but they work!)
Do you need professional PDFs? Try PDFmyURL!
The winding setup, ready for music wire.
Unlike previous springs, this one must be wound the exact number of turns desired as the
straight tails are part of the final product. By rotating the form, the coils are wound.
Do you need professional PDFs? Try PDFmyURL!
Starting the spring. The spring looks a bit ugly here because I released winding tension to take thepicture.
Complete the winding by snipping the ends of the spring stock and removing the raw
spring.
Do you need professional PDFs? Try PDFmyURL!
Completed winding of the hammer spring - only finish work is left.
I took a practice run and produced a mediocre spring, the next was what I wanted. For
the AK spring, the tails have a bend after the straight portion – in this way they serve
double duty, fulfilling the function of the trigger return spring as well as the hammer
spring. Bend the tails, trim, then bend the trimmed ends. The final spring fairly
resembles the spring it is patterned after. Here it is, installed on an AK hammer:
Do you need professional PDFs? Try PDFmyURL!
The completely formed spring, installed on an AK-47 hammer.
Temper the spring in the usual way, by baking at 450* for an hour.
If you’ve built AK ‘kits’ then you’ve probably replaced the factory trigger with US made
parts to be in compliance with 922r – winding springs for the old parts makes them
usable in other projects (bearing in mind that 922r still applies – you may not use more
than 10 ‘counting’ parts in a firearm).
Do you need professional PDFs? Try PDFmyURL!
← Green Mountain Barrels – follow up 1911 Detailed Disassembly →
Happy winding!
This entry was posted in Gunsmithing, Shop work. Bookmark the permalink.
Leave a Reply
Your email address will not be published. Required fields are marked *
Name *
Email *
Website
Comment
Do you need professional PDFs? Try PDFmyURL!
Firearms Designer
You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b><blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>
Post Comment
Proudly powered by WordPress.
Do you need professional PDFs? Try PDFmyURL!