making a rail car by stan pope and victor and rob
TRANSCRIPT
![Page 1: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/1.jpg)
Making a Rail Carby Stan Pope
and Victor and Rob
![Page 2: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/2.jpg)
Working axles - a groove to hold the nail
![Page 3: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/3.jpg)
Working axles - nail in the groove
![Page 4: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/4.jpg)
Working axles - ready to file the bumps off
![Page 5: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/5.jpg)
Working axles -holding the file steady
![Page 6: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/6.jpg)
Working axles - Guiding file with right hand
![Page 7: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/7.jpg)
Polish with jeweler's rouge on a rag.
![Page 8: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/8.jpg)
Draw the side views
![Page 9: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/9.jpg)
Draw the top view
![Page 10: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/10.jpg)
Line the drill up with the axle line and drill carefully
![Page 11: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/11.jpg)
At this point, cut the car off the block. Use whatever means are available ... table saw, hand saw, planer, etc.
![Page 12: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/12.jpg)
Make a place for the saw blade to work inside the car
![Page 13: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/13.jpg)
Cut out the end
![Page 14: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/14.jpg)
Detach one end of the blade ...
![Page 15: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/15.jpg)
Put the car around the blade ...
![Page 16: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/16.jpg)
Fasten the blade and you're “good to go.”
![Page 17: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/17.jpg)
A coping saw will do this job, too
![Page 18: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/18.jpg)
Weigh all the pieces, allow for epoxy.
![Page 19: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/19.jpg)
![Page 20: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/20.jpg)
Pound weights into shape to fitTape over the axle holes
![Page 21: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/21.jpg)
Set weights so that they are ready to go in the right place.
![Page 22: Making a Rail Car by Stan Pope and Victor and Rob](https://reader035.vdocuments.us/reader035/viewer/2022062809/56649f355503460f94c54054/html5/thumbnails/22.jpg)
Add Epoxy and fold the waxed paper over. Press to shape.