macromodular computer design, part 2, volume 09, faceplate

Washington University School of MedicineDigital Commons@Becker

Technical Reports Institute for Biomedical Computing

2-1974

Macromodular Computer Design, Part 2, Volume09, Faceplate Boxes, Types 5-10Computer Systems Laboratory, Washington University

Follow this and additional works at: http://digitalcommons.wustl.edu/bcl_techreports

This Technical Report is brought to you for free and open access by the Institute for Biomedical Computing at Digital Commons@Becker. It has beenaccepted for inclusion in Technical Reports by an authorized administrator of Digital Commons@Becker. For more information, please [email protected].

Recommended CitationComputer Systems Laboratory, Washington University, "Macromodular Computer Design, Part 2, Volume 09, Faceplate Boxes, Types5-10" (1974). Technical Reports. Paper 14.http://digitalcommons.wustl.edu/bcl_techreports/14

http://digitalcommons.wustl.edu?utm_source=digitalcommons.wustl.edu%2Fbcl_techreports%2F14&utm_medium=PDF&utm_campaign=PDFCoverPages

http://digitalcommons.wustl.edu/bcl_techreports?utm_source=digitalcommons.wustl.edu%2Fbcl_techreports%2F14&utm_medium=PDF&utm_campaign=PDFCoverPages

http://digitalcommons.wustl.edu/bcl?utm_source=digitalcommons.wustl.edu%2Fbcl_techreports%2F14&utm_medium=PDF&utm_campaign=PDFCoverPages

http://digitalcommons.wustl.edu/bcl_techreports?utm_source=digitalcommons.wustl.edu%2Fbcl_techreports%2F14&utm_medium=PDF&utm_campaign=PDFCoverPages

mailto:[email protected]

MACROMODULAR

CQMPUTEIR DES0®N

PART 2

MANUFACTURING DIESCIRDI?TION

VOLUME DX

FACEPLATE BOXES, TYPES 530

TechnicaU Repo.,r_' NOo :38

FINAL REPORT - FEBRUARY, 1974

CONTRACT SD-302 (ARPA)

COMPUTER SYSTEMS LABORATORY

WASHINGTON UNIVERSITY

ST. LOUIS, MISSOURI

MACROMODULAR COMPUTER DESIGN

FINAL REPORT - CONTRACT SD-302

,', FEBRUARY,1974

!

PART 2 MANUFACTURING DESCRIPTION

VOL. IX-FACEPLATE BOXES, TYPES 5-10

i

This work has been supported by the Advanced ResearchProjects Agency of the Department of Defense underContract SD-302 and by the Division of Research Facilitiesand Resources of the National Institutes of Healthunder Grant RR-00396.The views and conclusions contained in this documentare those of the authors and should not be interpreted

as necessarily representing the official policies,either expressed or implied, of the Advanced Research

_ Projects Agency or the U S. Government.

t_k Computer Systems Laboratory

Washington UniversitySt. Louis, Missouri

ABSTRACT

This document contains the necessary procedures

and wiring lists for the assembly of Macro-Module Face-

plate Box types5 through10.

INDEX

TYPE 5 FACEPLATE BOX

PAGES 305-1 thru 305-18


PAGES 306-1 thru 306-14


PAGES 307-1 thru 307-4


PAGES308-1 thru 308-4


PAGES 309-1 thru 309-23


PAGES 310-1 thru 310-24

r

s,,,,,s,,,o,,,o,, [305.WASHINGTON UNIVERSITY

TYPE5 FACEPLATEBOX

PAGE TITLE CHANGE

305-1 TITLE PAGE / A305-2 TYPE 5 FACEPLATE BOX PARTS LIST A

305-3TYP'E 5 FACEPLATE BOX - INTRODUCTION AND ASSEMBLY PROCEDURE A305-4

305-5 TYPE 5 FPB ASSEMBLY A

305-6 T'YPE 5 FPB REAR CONNECTOR BLOCK'-ASSEMBLY ORIENTATION A

305-7 TYPE 5 FPB VISCERAL SUBASSEMBLY A

305-8 TYPE 5 FPB INTERWIRING SUB-SUBASSEMBLY

305-9 TYPE 5 FACEPLATE SUB-SUBASSEMBLY'

305-10

THRU TYPE 5 FACEPLATE BOX WIRING LIST

305-18

JI

CHG. I E.C,O. DATE I APPR. CHG. E.C.O. DATE APPR. CHG. E,C.O, DATE APPR.

ISSUE! - 9/28/70 ...O-_(__,

I

A ! 0059 10-20-70i I

J i

MACROMODULAR SYSTEMS PROJECT

305---1

TYPE 5 FACEPLATE80X

PARTSLIST

QTY. ! C.S.L. DOC. PART.

I1 30001 1-CELL FPB SHELL

1 ' 300,5-11 TYPE 5 FACEPLATE

6 300,5-3 FPB CONNECTOR BRACKET SCREW

12 300,5-4 ASTRO STANDOFF

I 300_5-5 FPB KEY

2 300o0 FPB REAR CONNECTOR

3 ' 300:0 ASTRO 34B REAR NUT

3 300o0 ASTRO 348 CONTACT RETENTION DISC

3 30000 ASTRO 348 INTERFACIAL SEAL

1 11 300:0 ASTRO 348 MALE CONTACT

3 300:0 ASTRO RECEPTACLE SHELL

1 - VLIER #NS-51N SPRING PLUNGER

3 -, NO_2 SERRATED-HOLE SOLDER LU.G

28 - 3 '16 X 2-56 FILLISTER HEAD SS MACHINE SCREW

- 300_0 WiRE (SEE 305-10 ff FOR COLOR CODE)

9 - 130 OHM 1 S WATT 5% CARBON RE_,J_TOR

1 - 1/16 X 1'4 CADMIUM PLATED STEEL ROLL PiN

2 300,5-2 FPB CONNECTOR BRACJ_T

1 300,5-12 FPB REAR CONNECTOR FILLER STRIP

i

,CHG. E.C.O- DATE APPR. CHG. E.C.O. DATE APPR. CHG. E.C.O. DATE APPR.

S_IIE - 9/28/70 ,_,,_A oo59 ;o-2o-7oZ/_

MACROMODULARSYSTEMSPROJECT 305-'2'

ITYPE 5 FACEPLATE BOX

INTRODUCTION

This document (305) describes the assembly of the Type 5

Faceplate Box. A list of all required parts, including sub-

assemblies specified in other documents, is given on page 305-2.

The general specification on wire preparation and wiring proce-

dures (CSL Document 300.0) must be followed, together with the

color code information supplied by the Type 5 Faceplate Box

Wiring List (pages 305-10 ff).

ASSEMBLY PROCEDURE

A,' Type 5 Faceplate Sub-subassembly (see page 305-9__

1, Screw the spring' plunger into the faceplate untilthe tip of the plunger protrudes from the frontsurface of the faceplate by approximately 0.090 inch.

2. Mount the three ASTRO 348 receptacle shells via theASTRO standoffs to the faceplate as shown on page505-9 using 2-56 fillister head screws. NOTE THEORIENTATIONREQUIRED.

3. Install the roll pin in the lower right cornerhole as shown, flush with the rear Surface ofthe faceplate (protruding from the front surfaceapproximately 1/16 inch).

B, Typ_ 5 FPB Interwiring Sub-subassembly (see page 305'8)

1. Connectors D1, D2 and DSFollowing the Type 5 Faceplate Box Wiring List,crimp the wire pairs and the nine resistors into theASTRO 348 male contacts and insert the contacts into

designated contact retention discs (pin numbering isstamped in the receptacle shell). Apply the inter-facial seals and slip on the rear nuts.

2. Wire to the FPB rear connectors A3, and A4, toge-ther with three solder-lug leads.

CHG. E.C.O. DATE APPR.

Iss_ - 9/28/70 _O_U

I.

J

, ; J305-3

C. Type 5Visceral Subassembly (see page 305-7)

1. Mount the F'PB rear connector fillerstrip on the two connector brackets with con-nector bracket screws, as shown on page (305-6). Note that the row of holes is not centeredon the bracket. The bracket edge closest tothe row of holes must face inward (towards theconnector pins). NOTE CONNECTOR ORIENTATIONRE-QUIRED.

2. Install the contact retention disc cable-head

assemblies in the corresponding receptacleshells for D1, D2 and D3 (shown on page 305-9)and hand-tighten the ASTRO 348 Rear Nuts.

3. Attach the solder lugs to the receptacle shellsas shown.

4. Mount FPB Rear Connector A4 to the connectorbrackets using connector bracket screws. NOTECONNECTOR ORIENTATION REQUIRED.

5. Slip the FPB Key onto the connector brackets,and mount the FPB Rear Connector A3 using thetwo remaining connector bracket screws. NOTETHE ORIENTATION REQUIRED.

D. Final Assembly (see page 305.-5)

1. Remove the four screws holding the top coverplate to the 1-cell FPB Shell struts and removethe top cover plate and the top overlay clip.

2. Slip the rear connector block of the VisceralSubassembly into the slots provided in thestruts for the connector brackets, and attachthe Faceplate to the front using the remaining2-56 fillister head screws. NOTE THE ORIENTATIONREQUIRED.

3. Reinstall the top overlay clip and attach thetop cover plate, taking care to assure that thewires are not pinched.


Issu._ - 9/28/70 _SYC_^ oos9 ,0-20-70

l

305 -4

OVERLAY CLIPTOP COVER PL re-/TOP

/

- MOUNTI NG

SCREWS

FIXED ROLL PIN STUD

I -CELL FPB SHELL j

ITYPE S FPB VISCERAL SUBASSEMBLY

(SEE PAGE 305-7_I

NOTE ORIENTATION

11 ii

I rifLE

COMPUTERSYSTEMSLABORATORY TYPE 5 FPB ASSEMBLYWASHINGTON UNIVERSITY

lINC,. On,w,_G _o,ST. LOUIS, MI_SOURI AppmOV£O

,, ,_.... _ iWAC 305-5A 'O-Zl-;'O E.C.O. OOS9 _ MACROMODULAR PROJECT _kf PROa [,o-2o-?o!o._..k

I ' ii IDA*EC"_C ED

, ,, I L._z_' i lO-_O-7O

FPB CONNECTOR BRACKET'

FP8 REAR CONNECTOR

FPB KEY /

-- FPB REA RFILLER STRIP

FP8 REAR CONNECTOR A 4_

I --KEY TAB EXTENDS ,LEFTWARDS

NOTE ORIENTATION OF EACH PART

' COMPUTER SYSTEMS LABORATORY MACROMODULAR PROJECTWASHINGTON UNIVERSITY

TITLE

, ST.LOUIS,MISSOURI TYPE S FPB REAR CONNECTORBLOCK- ASSEMBLY ORIENTATION

APPROVED ENG DRAWING NO.

BY FOR DATE WA C

4.z_d 305-6A ,o._o-,,,E.c,b oos9 _ PRoo._o-_o-7o°_/-/b,,,o. o,,_'E O_R,,'r,o,,, :/--__.._"'_ I0-- 20-70

/

I I

TYPE 5 FACEPLATE(SEE PAGE 305-9)

FPB REAR CA3

TYPE 5 FPB INTERWIRINGSUB-SUBASSEMBLY (SEE PAGE 305-8)

FPB

FPB CONNECTOR BRACKET

FPB REAR CONNECTOR FPB CONNECTOR BRACKET SCREWSA4

FPB REAR CONNECTOR FILLER

TITLE

COMPUTERSYSTEMSLABORATORY TYPE S FPB VISCERAL SUBASSEMBLYi WASHINGTON UNIVERSITY

] St LOUIS. MIRSOURI *pp. OV£O E";' I :_*w_~_ ~0,9..... GCJ I

, _/_ ....... 305-7A io-zo .70 E.C.O.0059 _'_' MACROMODULAR PROJECT PROD. fo-,o-7o DHO

......,o _.............. z,/,_ IO-_O-7O

REAR CONNECTOR A3

SOLDER LUGS_( DS

_, D2

I

&

REAR NUT --_ MALE CONTACTS

RESISTOR INTERFACIAL. SEAL

CONTACT RETENTION, DISC

L FPB REAR CONNECTOR A 4

'tITLE

COMPUTER SYSTEMS LABORATORY TYPE .5 FPB INTERWIRING SUB-.SUBASSEMBLYWASHINGTON UNIVERSITY

I

ST. LOUIS, MISSOURI Ippc_OVED £_G O_AWJ_G ~0

...... FgR GC..J '3t'"lz_' O

Oj_/_ PROD. 9,28-ZC p L L)SSUE 9_8-70 ._C_ MACROMODULAR PROJECT '6,"

......' _c_,o ................ q ._ 7n- -____f.-,

iiii _//

(D 1) (D2) (D$) ASTRO PLUNGER

NOTE '1ORI ENTA TION t

-- ROLL PIN SUNK FLUSHTYPE $ FACEPLATE -- WITH REAR SURFACE

ASTRO 348 RECEPTACLE SHELLS

iiii

i TITLE

COMPUTERSYSTEMSLABORATORY TYPE 5 FACEPLATE SUB-SUBASSEMBLY!i WASHINGTON UNIVERSITY

I

S'E LOUIS, MISSOURI Ar'PROV_:O I E._, o_^wtN_ NO, I GCJ '

.,._, , ,_9. _"'_ PL L 305-9

'/SSUEc.,.o,,-_a-?Oo,,__'"¢_ MACROMOOULAR PROJECT .._._._._ e,qoo. ,-,_¢70 .......i C. _EO DATE

I(./

FPTSWL,! LN=]

(FPT$C[FAC[PLATE TYPE 5 WIRING LIST[

mIA3 [SIX INCH WIRE WITH GROUND LUG

[CONNECT TO D!#

2A3 [SIX INCH WIRE WITH GROUND LUG[CONNECT TO D2#

3A324D! [ ORANGE

4A323D! [ RED

#

5A333D! [ BLUE

#6A332D! [ RED

m

7A33IDI [ SLATE

.8A3I300] [ YELLOW

9A337D! [ ORANGE

IOA336D! [ YELLOg

#

!IA324D_ [ ORANGE

!_A3[3DE [ RED '

_>_>>>>>>>>>>>>>!3R3 CH_. E.C.O. D_TE App..

. 33DE ( BLUE ISSUE _ 9/28/70 _

I 4A3 , _/3ED2 [ RED

i

! 5A3

3ID[ [ SLATE 305-10

FPT5WLJ2 LN-?2

16A330D2 £ YELLOW

#

19A339D2 £ ORANGE

#18A336D2 [ YELLOW

#

19A322DI £ BLUE

#

20A322D2 t BLUE

#

21A321DI t BROWN

#22A320DI £ YELLOW

#

23A3: 17DI £ GREEN

24A316DI [ YELLOW

#

25A328D1 [ SLATE

26A327DI [ WHITE

27A326DI ; BROWN

#28A325D1 [ RED

#

29A32lo2 [ BROWN

#30A320D2 [ YELLOW

#

31A3I 7D2 [ GREEN 305-11

FPTSWL_3 LN=I63

#32A3!6D2 £ YELLOW

#

33A328D2 ( SLATE

O34A32TD2 r WHITE

/i

35A3E6DE ( BROWN

#36A3ESDE E RED

W

3TA3 ENO CONNECT]ONm

38A3 (NO CONNECTION#

39A39D! ( ORANGE

#40A38DI (.WHITE

41A315D! I: GREEN

42A3! 4DI [ RED

#

43A313DI ( GREEN

o

44A3I_DI E WHITE

#

45A3lID! [ BROWN

46A3IODI r WHITE

47A39D2 [ ORANGE

48A3 305-I 2

FPT5WI.,,, 4 LN=254

8D2 [ WHITE

49A3I5DR [ GREEN

50A3]4D2 [ RED

51A3 IN0 CONNECTION

52A3 [NO CONNECTION

53A313D2 [ GREEN

#54A312D2 [ WHITE

55A3liD2 [ BROWN

56A3tOD2 [ WHITE

#

57A3 [NO CONNECTION

58A3 [NO CONNECTION

59A3 [NO CONNECTION#

60A3 [NO CONNECTION· #

6lA318D2 [ VIOLET

62A319D2 [ BLUE

63A318DI [ VIOLET

64A34

IgDi [ BLUE

65A3 [NO CONNECTION 305-13

I FPT5WL,5 LN=345


9_9999_99999._


68A3 (NO CONNECTION

9_99_999_99

69A3 [NO CONNECTIONm

_99_9999999999

TOA3 [NO CONNECTION

9_'_99_9_9)_9_99

7IA360! ( VIOLET

?aA31DI [ ORANGE

#99999_)999)99999

73A36D2 £ VIOLET

#74A3?D2 [ ORANGE

_9999999_99_9

75A329D2 [ GREEN

_999_9999999999

76A329D1 £ GREEN

9999999_99._99

(FOUR WIRES ARE SOLDERED TO PIN 77A3.??A3SD! [ YELLOW5D2 £ YELLOWSD3 C YELLOH90A4

[ 99_99._9_999999 - *,

(PINS 78A3 THROUGH 90A3 INCLUSIVE HAVE NO CONNECTION(

+

(ONLY EVEN NUNBERED PINS OF CONNECTOR A4 ARE USED WITH THEEXCEPTIONS OF IA4 AND 5A4. ALL OTHER ODD NUNBERED PINS ARE[NO CONNECTION.[

lA4a2D3 ( BLUE

0)0)99))999)999, 305-14

FPTSWL* 6 LN=434

2A424D3 [ ORANGE

? #4A423D3 [ RED

#

5A4 [SIX INCH WIRE WITH GROUND LUG[CONNECT TO D3m

6A433D3 ( BLUE

8A432D3 ( RED

m

! OA431D3 [ SLATE

#12A430D3 [ YELLOW

14A43?D3 [ ORANGE

#16A436D3 [ YELLOW

8

I 8A421D3 [ BROWN

#20A420D3 [ YELLOW

#

22A417D3 [ GREEN

#24A4!6D3 £ YELLOW

. 26A4_-8D3 [ SLATE

#28R427D3 [ WHITE

#

30A426D3 [ BROWN

3EA4 305-15

FPTSWL* 7 LN=525

25D3 E RED#

34A49D3 [ ORANGE

#36A48D3 [ WHITE

#

38A4!5D3 [ GREEN

#40A414D3 [ RED

4EA413D3 [ GREEN

#44A412D3 [ WHITE

#

46A4!ID3 [ BROWN

#48A4IOD3 [ WHITE

SOA4!8D3 [ VIOLET

#52A419D3 [ BLUE

5ZiAZ_6D3 [ VIOLET

#56A47D3 [ ORANGE

#

[[PINS 58AZl THROUGH 88A4 INCLUSIVE ARE NO CONNECTION.[

9OA4 [SEE 77A3#

[[THE FOLLOWING ARE RESISTORS WITH THEIR LEADS CRIMPED DIRECTLYINTO THE INDICATED CONNECTOR CONTACTS. THE LEADS SHALL BECOVERED BY TEFLON SLEEVING_, AND THE COLOR CODE NAY BE IGNORED.[

IR601 305-16

I

I

FPT5WL, IO LN=614

1D! [ RED

RR6012DI [ SLATE

IR6023DI [ YELLOW

#2R6024DI ,[ BLUE

1R60334D! [ WHITE

#

2R6033SDI [ BLUE

IR604ID2 [ RED

#2R6042D2 [ SLATE

IR6053D2 [ YELLOW

#2R6054D2 [ BLUE

#

IR60634D2 [ _HITE

2R60635D2 [ BLUE

#

IR607ID3 [ RED

2R6072D3 [ SLATE

#

IR6083D3 [ YELLOW

4D3 [ BLUE

tR609

34D3 [ WHITE 305-17

FPTSWL, 11 LN=70S . "

#2R60935D3 [ BLUE

#

[[END OF WIRING LIST[CCFPTSWLCGERALD C JOHNS[ 2 OCTOBER 1970

305-18

I' I.o.,,u,,.,,.,,,M,.,,,o.,,,o.,. 306WASHINGTON UNIVERSITY

TYPE6 FACEPLATEBOX

PAGE TITLE CHANGE

306-1 TITLE PAGE ISSUE

306-2 TYPE 6 FACEPLATE BOX PARTS LIST

306-3 TYPE 6 FACEPLATE BOX - INTRODUCTION AND ASSEMBLY PROCEDURE306-4

306-5 TYPE 6 FPB ASSEMBLY

306-6 TYPE 6 FPB REAR CONNECTOR BLOCK - ASSEMBLY ORIENTATION

306-7 TYPE 6 FPB VISCERAL SUBASSEMBLY

306-8 TYPE 6 FPB INTERWIRING SUB-SUBASSEMBLY i

306-9 TYPE 6 FACEPLATE SUB-SUBASSEMBLY

306-10 CONNECTOR PIN DESIGNATION

306-11

thru TYPE 6 FACEPLATE BOX WIRING LIST

.306-14

t

CHG. i E.C.G. DATE APPR CHG, E.C.O. DATE APPR CHG. E.C.O. DATE APPR.


306-1

TYPE6 FAC£PLATEBO,'(PARTSLIST

/

QTY. C.S.L. DOC, PART

1 300,1 1-CELL FPB SHELL

1 300,,5-15 TYPE 6 FACEPLATE

2 300°5-3 FPB CONNECTOR BRACKET SCREW

1 300.5-5 FPB KEY

1 30006 V-BUS SUBASSEMBLY

1 300,0 FPB REAR CONNECTOR

1 300o7-3 TYPE 1 FUNCTION CODE SWITCH SUBASSEMBLY

8 300,0 COAXICON

8 300,0 FERRULE

I - VLIER #NS-S1N SPRING PLUNGER

122 - 3/16 x 2-56 FILLISTER HEAD SS MACHINE SCREWi

300,0 WIRE (SEE 306-11 ff FOR COLOR CODE)

3 AMPHENOL 31-223 TWIN BNC CONNECTORS

"3 3/8INCH SOLDER LUG

CNG. E.C,O. DATE APPR. I CHG. E.C.O. DATE APPR. rCHG. E.C.O. DATE APPR.

ISSUE' - 1-25-72 _

I i

m I IMACROMODULAR SYSTEMS PROJECT

306-2

\


INTRODUCTION

This document (306) describes the assembly of the Type 6

Faceplate Box. A summary list of all required parts, including

subassemblies specified in other documents, is given on page

306-2. The general specification on wire preparation and wiringprocedures (CSL Document 300.0) must be followed, together with

the color code information supplied by the Type 6 Faceplate BoxWiring List (pages 306-11 ff).

ASSEMBLY PROCEDURE

A. Type 6 Face, late Sub?subassembly (see page 306-9)

1) Crimp-wire the set of eight coaxicon control

connectors and press the resulting pre-wiredconnectors into the faceplate in the locations

shown on page 306-9, taking care to assure that

after installation the connectors will accept amating coaxicon plug without binding. NOTE THEORIENTATION REQUIRED.

' 2) Screw the spring plunger into the faceplate untilthe tip of the plunger protrudes from the front

surface of the faceplate by approximately 0.090 inch.

3) Mount the three coax connectors with solder lugs tothe faceplate as shown on page 306-9. The lock-

washers are to be placed in the counterbored hole

in the front of the faceplate before inserting theconnector. NOTE THE ORIENTATION REQUIRED.

B. Type 6 FPB Interwiring Sub-subassembly (see page 306-8)

1) Jumper the Type 6 Function Code Switch Sub-assemblyand wire to the FPB Rear Connector A3.

C. Type 6 Visceral Subassembly (see page 306-7)

1) Mount the Function Code Switch Subassembly on thefaceplate using two 2-56 fillister head screws.

The sense pins must operate freely.

C _JC,. E.C.O. DATE A t:_PR.

ISSUE - 1-25-72

306-3

I

i

2) Wire the leads from the coaxicon control connectorsand the coax connectors to the FPB RearConnector A3.

3) Wire coax connectors.

4) Rear connector block:

Slip the FPB Key onto the V-Bus Subassemblyconnector brackets, and mount the FPB Rear

Connector A3 using the two connector bracket

screws. NOTE THE ORIENTATION REQUIRED (page 306-6).

D. Final Assembly (see page 306-5)

1) Remove the four screws holding the top cover plate

to the 1-cell FPB Shell struts and remove the top

cover plate and the top overlay clip.

2) Slip the rear connector block of the Visceral

Subassembly into the slots provided in the

struts for the connector brackets, and attach

the Faceplate to the front using the remaining2-56 fillister head screws. NOTE ·THE ORIENTATION

REQUIRED.

·3) Reinstall the top overlay clip and attach the topcover plate, taking care to assure that the wires

are not pinched.

CHG. E.c.O_ -' DATE APPR. 1ISSUE - 1-2s-72 _ jI

...

!

_ I306_4

TOPOVERLAYCLIP

TOPCOVERPLATE

MOUNTING

SCREWS

1-CELLFPBSHELL ITYPE 6FPB VISCERALSUBASSEUBLY-

(SEE PAGE 306-7)

NOTE ORIENTATION

TIT[.E

COMPUTER SYSTEMS LABORATORY TYPE6 FPBASSEMBLYWASHINGTON UNIVERSITY

ST LOUIS, MISSOURI APPnOVEO ENG. DRAWI,_ NO.

_¥ _,o. D^T_ FUR 306-5

PROD. .2-3-7_o.^.,_,pissu_ ]_-_7-7g_ MACROMODULAR PROJECTCMECKED OATE

NO. DATE i DESCRIPTIONi I I

i

' FPB REAR

F 'B KEY

NOTEORIENTATION

!¥'

V-BUS SUBASSEMBLY

NOTE ORIENTATION

(KEY TAB EXTENDSRIGHTWARD)

COMPUTERSYSTEMSLABORATORY MACROMODULAR PROJECTWASHINGTON UNIVERSITY

ST.LOUIS, MISSOURI TITLE TYPE6'FPB REARCONNECTORBLOCK-ASSEMBLY'ORIENTATION

i

A,,OVED E.GFUR 'D_W,NG,O., _o_ I ,,ATE . 306-6

ISSUE 5-2?'77 _ _ PROD..2-3-7.2 D,_w,,,MBPCHECKED DAZE

CHANGE DATE DESCRIPTION J,o. .L '_-_'_' 1-27-72i

TYPE6 FPBINTERWlRINGSUB-SUBASSEMBLY(SEEPAGE306-8)

" CONNECTORBRACKETSCREW 6FACEPLATESUB-SUBASSEMBLY

_ (SEEPAGE306-9)

I

'Z:

,V-BUSSUBASSEMBLY

LFPB XEY

i

TITLE

COMPUTER SYSTEMS LABORATORY TYPE6 FPBVISCERALSUBASSEMBLY


ST. LOUIS, MISSOURI APPROVED ENG. DRAWINGNO.

DY .o. O^TE FUR 306-7

PROD. 2 -3-7._ .......MBPISSUE ]-27-72 _ MACROMODULAR PROJECT

CHECKEO DATE

.o. D^TE o_sc...T,o. 1-27-72i mu i

TYPE I FPB FUNCTIONCODE SWITCHSUBASSEMBLY

j- -../

/

( ?, .i4/' '_

· . . ..

] --:

FPB REARCONNECTOR f_

A4 / ,//

J

COMPUTERSYSTEMSLABORATORY MACROMODULAR PROJECTWASHINGTONUNIVERSITY

ST.LOUIS,MISSOURI ,,,,E TYPE6 FPB FUNCTIONCODEWIRINGSUB-SUBASSEMBLY

A,.OVED '"0 FUIt O,'W,.O.NO., ,o. DA,E 306-8

· _ PROD, 2o3-_'._ 0"""_11_'1:', _llr 1-27-72CHANGE CHECKED DATE

NO. DA.E DE.C.,,",O. '_'-'_,4' 11-27-72,I

.NOTEORIENTATION

SOLDER LUG

SPRING PLUNGERCOAX CONNECTORS

! TYPE6FACEPLATE V _3 G,:

/

NOTE ORIENTATION

. .'

il

· _'.'::'i<

PRESS FiT G2 G4 G8PREWIREDCONTROLCONNECTORS

I

TITLE

COMPUTER SYSTEMS LASORATORY TYPE 6 FACEPLATE SUB-SUBASSE_',_BLY

WASHINGTON UNIVERSITY ORAWiNG NC,,

ST. L.OUIS, M'SSOURi ........ /i .... _'URDY Eo,_ , mAT,, 306--9

PROD. .2-_-_'[ o.,,._j:_

,,_,,r 1'-?_-77_ MACROMODULAR PROJECT /_...... 'C_ A_*GE. DATE OIE$C_IPT _ON '

HO.

c_,_,_FERRULE_,N,l'0

PIN 2 1

(_ PIN 3 IS SOLDER\

SOLDER LUG _ LUG

-

, (/

PIN 1. PIN 2MA L E FEMA L E

COMPUTER'SYSTEMS LAI3ORATORY MACROMODULAR PROJECTWASHINGTON UNIVERSITY

ST. LOUIS, MISSOURI TITLE

! CONNECTOR PIN DESIGNATION

APPROVED ENG DEAWING NO,

,, ,o, D,,, FUR

ISSUt' 1-25-72 .c._u., pRoD.._-_-?_ :D'*_l"L 306-- !0CHANGE _ i CHECKED DATE

NO. DATE OE_,,,,O, _'_'_ I --25 --72

FPT6WL, 1 LN=I

[FPT6C

[FACEPLATE TYPE 6 WIRING LIST[[#

1A3 [NO CONNECTION#

>>>>>>>>>>>>>>>>2A3

3V1 [BLUE>>>>>>>>>>>>>>>>

#

3A3 [NO CONNECTION#

>>>>>>>>>>>>>>>>4A3 [NO CONNECTION

#

>>>>>>>>>>>>>>>>5A3

1V1 [WHITE#

6A3

2V1[GREEN#

>>>>>>>>>>>>>>>>7A3 [NO CONNECTION

#

>>>>>>>>>>>>>>>>8A3 [NO CONNECTION

#

>>>>>>>>>>>>>>>>9A3 [ NO CONNECTION

#

>>>>>>>>>>>>>>>>10A3

3V2 [BLUE#

>>>>>>>>>>>>>>>>11A3 [hY) CONNECTIO_

#

>>>>>>>>>>>>>>>>12A3 [NO CONhTECTION

#

>>>>>>>>>>>>>>>>1 3A3

1V2 [RED#

14A3 !C,G. E.C.O. DATE APPR. 1

2V2 [ORANGE iSSUE - i i.25.72/

#>>>>>>>>>>>>>>>> I15A3 i

3G5[BLUE#

>>>>>>>>>>>>>>>>1 6A3

3G1 [ BLUE 306-1!

FPT6WL, 2 LN=72

#

>>>>>>>>>>>>>>>>17A3

1G5 [ WHITE#

18A3

2G5 [ SLATE#

>>>>>>>>>>>>>>>>19A3

2G1 [ BLUE-#

20A3

1G1 [ W}{ITE#

>>>>>>>>>>>>>>>>21A3

2G3 [ GREEN#

22A3

1G3 [ WHITE !

#>>>>>>>>>>>>>>>>23A3

3G3 [ BLUE.#

>>>>>>>>>>>>>>>>24A3

3G4 [ BLUE-#

>>>>>>>>>>>>>>>>26A3

1G4 [ WHITE#

25A3

2G_ [ BROWN#

>>>>>>>>>>>>>>>>27A3

1G2 [ W}{ITF_.#

28A3

2G2 [ ORANGE#

>>>>>>>>>>>>>>>>29A3

1GG [ YFLLOW# :: CHG. E.C.O. DATE Al) pR.

]

3OA3 ISSUE . !-25-722G6 [ BLUE

#

>>>>>>>>>>>>>>>>31A3

2S4 [BLUE b,

#>>>>>>>>>>>>>>>>

32A3 506-12

FPT6WL t3 LN=I 63

3G6[#

>>>>>>>>>>>>>>>>33A3

2S5 [BLUE#

>>>>>>>>>>>>>>>>34A3

3G2 [ BLUE#

>>>>>>>>>>>>>>>>35A3

3S2 [RED#

>>>>>>>>>>>>>>>>36A3 [NO CONNECTION

#

>>>>>>>>>>>>>>>>37A3

'3S3 [RED,#

>>>>>>>>>>>>>>>>56A3

2si#[PINS 38A3 THROUGH 55A3 INCLUSIVE ARE NO CONNF_.CTION

>>>>>>>>>>>>>>>>58A3

3G8 [ BLUE.#

>>>>>>>>>>>>>>>>59A3

1G8 [ YELLOW#

60A3

2G8 [ GREEN#

>>>>>>>>>>>>>>>>I 61A3

1S1 [YELLOW1S2 [YELLOW1S3 [YELLOWIs4 [YELLOW1S5 [YELLOW

#

>>>>>>>>>>>>>>>>62A3 [NO CONNECTION j

# CHG. £.C.0. DATE APPR.

>>>>>>>>>>>>>>>> iSSUE - 1-25,-72 _ ,63A3 [5_D CONNECTION

#>>>>>>>>>>>>>>>>64A3 [NO .CONNECTION

>>>>>>>>>>>>>>>> ...........65A3 -'

1V3 [YELLOW 306-13# m

J

FPT6WL, 4 LN=254

66A3

2V3 [BLUE#

>>>>>>>>>>>>>>>>67A 3

3V3 [BLUE#

>>>>>>>>>>>>>>>>68A3

3G7 [ BLU_-,#

>>>>>>>>>>>>>>>>69A3

1G7 [ YELLOW#

70A3

2G7 [ ORANGE#

>>>>>>>>>>>>>>>>[ PINS 71A3 THROUGH 90A3 INCLUSIVE APE NO CONNFCTION

[[END OF WIRING LIST,[[FPT6C[27 DECEMBER1971

[GERALD C JOHNS[EPT6WL

- , n ,, · ,


ISSUE . 1.25;.72_'_

306-14

_o,.u,..,,.,., ,,,o.,,o., 13071WASHINGTONUNIVERSITY

TYPE7 FACEPLATE BOX

PAGE TITLE CHANGE

307-1 TITLE PAGE ISSUE

307-2 PARTS LIST

307-3 INTRODUCTION AND ASSEI4BLY PROCEDURE


I

CHG. I E.C.O. DATE APPR CHG E.C.O. DATE APPR CHG. E.C.O. DATE APPR.

SSUE , - 2-29-72 _:_ _/,,_

MACROMODULAR SYSTEMS PROJECT on't 1,3U/ ,L

TYPE7 FACEPLATEBOX

PARTSLIST

QTY: C.S.L. DOC. PART

1 300,,1 1-CELL FPB SHELL

1 300o5-18 TYPE 7 FACEPLATE

1 300,5-16 TYPE 7 REAR CONNECTOR FILLER STRIP

I 300.6 V-BUS SUBASSEMBLY

1 - VLIER NO. NS-S1N SPRING PLUNGER2 300_5-3 FPB CONNECTOR BRACKET SCREW

4 - 3/16 x 2-56 FILLISTER HEAD SS MACHINE SCREWS

i!

!

CHG. E.C.O. DATE APPR. CHG. E.C.O. DATE APPR. CHG. E.C.O. J DATE APPR.

kSSUE - 2-29-72 _ ',./_

MACROMODULAR SYSTEMS PROJECT· 307-2

INTRODUCTION AND ASSEMBLY PROCEDURE

Introduction

This document (307) describes the assembly of the type 7

Faceplate box. A summary list of all required parts, includingsubassemblies specified in other documents, is given on page307-2.

Assembly Procedure

1) Screw the spring plunger into the faceplate until the tip

of the plunger protrudes from the front surface of thefaceplate by approximately .090 inch.

2) Onto the V-Bus Subassembly mount the type 7 FPB rearconnector filler strip using the two connector bracketscrews. Note the orientation required.

3) Remove the four screws holding the top cover plate to the1-cell FPB shell struts and remove the top cover plate and

the overlay clip.

4) Slip the V-bus subassembly into the slots provided inthe struts for the connector brackets, and attach the

Faceplate to the front using the four 2-56 fillister head

screws. Note the orientation required_

5) Reinstall the top overlay clip and top cover plate.

CItO. j -E'i'C.O. DATE APPR. J

BSsu':l _ 2-2_-_ ,,_,.,.;'._1

I

307-3

I '1 I I I I

TYPE7 FPBREAR TOPCOVERPLATE OVEI CLIPCONNECTORFILLERSTRIP

SPRINGPLUNGER

MOUNTINGSCREWS /TYPE 7FACEPLATE 'WBUS SUBASSEMBLY

I

TITt.£

COMPUTER SYSTEMS LABORATORY TYPE7 FPBASSEUBLYi


i ilmmli i i RmiaST, LOUIS, MISSOURI A_PROVEO e:NG,DRAWING NO.

307-4DY F_R DATE

,qJA PROD. 3-1-72 °"^"" "_ISSUE 2-29-72_,.'.4 MACROMODULAR PROJECT MBPi i

- ....C.^.Ot 2-29-72NO. DATE DESCRIPTION] I IIII I III

,o.,u,,.., ,.,o.,,o,, 1308JWASHINGION uNIVERSIIY

TYPE 8 FACEPLATEB0X

PAGE TITLE I CHANGE

308-1 TITLEPAGE ISSUE Ii

'308-2 PARTS LIST

1.308-3 INTRODUCTION AND ASSEMBLY PROCEDURE

308-4 TYPE 8 FPB ASSEMBLY __;

I

CHG.' EoC.Oo DATE APPR CHG E.C,O. DATE APPR CHG. E.C.O. DATE APPR,

ISSUE - 2-29-72 y_ ¢j ,,,_


308-1

TYPE8 FACEPLATEBOXPARTSLIST

QTY: C.S.L. DOC. PART

1 300_1 1-CELL FPB SHELL

1 300_5-18 TYPE 8 FACEPLATE

1 300_5-17 TYPE 8 FPB FILLER

I - VLIER NO. NS-51N SPRING PLUNGER

4 - 3/16 x 2-56 FILLISTER HEAD SS MACHINE SCREWS

CHG. E.C.O. DATE APPR. I CHG. E.C.O. DATE APPR. CHG. E.C.O. DATE APPR,J

ISSUE - 2-29-72 _'k./,_'

I

I JMACROMODULAR SYSTEMS PROJECT

308-2

INTRODUCTION AND ASSEMBLY PROCEDURE

Introduction

This document (308) describes the assembly of the type 8

Faceplate box. A summary list of all required parts, including

subassemblies specified in other documents, is given on page308-2.

Assembly Procedure

1) Screw the spring plunger into the faceplate until the tip

of the plunger protrudes from the front surface of thefaceplate by approximately .090 inch.

2) Remove the four screws holding the top cover plate to the

1-cell FPB shell struts and remoye the top cover plate andthe overlay clip.

3) Slip the type 8 FPB filler into the slots provided in the

struts and attach the Faceplate to the front using the four2-56 fillister head screws. Note the orientation of the

Faceplate.

4) Reinstall the top overlay clip and the top cover plate.

CHG. 'E.C.O. J' DATE- i APPR:u,4ISSUE - 2.29-72 ',,_

308-3ii

i

ii mi i

SPRING PLUNGER TOP COVER PLATE OVERLAY CLIP

MOUNTING SCREWS

TYPE 8 FACEPLATE TYPE 8 FPB FILLER

J

ii _1 i iiiTITLE

COMPUTER SYSTEMS LABORATORY TYPE 8 FPB ASSEMBLY

WASHINGTON UNIVERSITYi

ST. LOUIS, MISSOUR_ AWW,_OVE[O I ,.G. RJA 0._.,._ ,,o.' aY ,on p,^*r_ 308-4

ISSUE 2-29-72,'_,;A , MACROMODULAR PROJECT i_:'-/A PROD. 3-J-7,t....._i_)_p

,_.._.,, .... ,, ,CHANGE

.o. o_._t o_sc.,..,o. ' i 2-29-72

o PuT , 1309lWASHINGTON UNIVERSITY

TYPE9 FPB

PAGE TITLE CHANGE i309-1 TITLEPAGE iSSUE

309-2 PARTS LIST

309-3

thru INTRODUCTION AND ASSEMBLY PROCEDURES

309-4


309-6 TYPE 9 FPB VISCERAL SUBASSEMBLY

?;09-7 TYPE 9 FA('EPLATE ('OMPONENT ORIENTATION309_8 TYPE 9 t-'ACI{PLAT!_ SUB-SUBASSI-.MBLY FRONT-V_I-W

309-9 PC BOARD ASSEMBLY JIG

309-10 PC BOARD WIRING

309-11 VIKING CONNECTOR WIRIN(, INSTRU('TiONS

309-.12 l.l(D ORl I.iNTATION

309-13

thru WIRI{ I.IST !:OR ('OAXI('()NS309- t 4

309..1,5 WIRE I.IST FOR P(' BOARD HOI.ES309-.16 WIRE LIST t::OR VIKIN(; ('ONNI{("I'()R

=309-17 WI!;_!.:1.15;T !:()R ('()[1!{ .',;wrF('H309-. I 8

thru TYPI: 9 ]:PB WIR!N(; I.IST

309- 23

J

FCHGECO. DATE APPR. CHG. E.C.O. DATE APPR.![CHG. E.C.O. DATE [APPR!ss ...... 6-15-73 ,_ d,,4'

iI



PARTS LIST

QTY_ C.S.L. DOC, PART

1 . 300.1 1-CELL EPB SHELL

I 1 300.5-27 TYPE 9 FACEPLATE

! 2 300.5-3 FPB CONNECTOR BRACKET SCRE W

4 300.5-4 ASTRO STANDOFF

I 300.5-5 FPB KEY

1 300.6 V-BUS SUBASSEMBLY

I 300.0 FPB REAR CONNECTOR

I 300.7 TYPE 3 FUNCTION CODE SWITCH SUBASSEMBLY

1 VLIER NO. NS-5IN SPRING PLUNGER

20 2-56 x 3/16 FILLISTER HEAD SS MACHINE SCREWI

-- i300.0 WIRE (SEE 301-10 ff FOR COLOR CODE)1 VIKING CONNECTOR NO. 3VH10/1JN52 300.5-19 CONNECTOR STRUTS TYPE 1

2 300.5-21 STRUT COVERS

2 4-40 x 3/8 BINDER HEAD SCREWS1 VIKING POLARIZING KEY NO. 091-0071-000

1 8-32HEXNUT

5 INTERSWITCH NO. 675-022-100 DATA MODULE

1 300.5-28 WCL0208-1 CIRCUIT BOARD2 MONSANTO NO. MV5023 LIGHT EMITTING DIODES

15 300.0 COAXICON

15 300.0 COAXICON FERRULE

i i

CHG. E.C.O. DATE APPR. I CHG. I E.C.O. DATE APPR. CHG. E.C.O. DATE : APPR,_ss, 6-15-73 _,./.4


309-2

INTRODUCTION

This document (309) describes the assembly of the Type 9 Faceplate Box. A summary

list of all required parts, including subassemblies specified in other documents, is given on page 309-2.

The general specification on wire preparation and wire procedures (CSL Document 300.0) must be

followed, together with the color code information supplied by the wire lists for the Type 9 Box

(pages 309-13 ff).

ASSEMBLY PROCEDURE '

A. Type 9 Faceplate Subassembly

1) Following the table on page 309-13, crimp wire pairs into the coaxicon connectors.

2) Press the coaxicon connectors into the faceplate as shown in page 309-8. Note the

orientation.

3) Screw the spring plunger into the faceplate until the tip protrudes approximately 0.090 inch

from the front surface. Lock the plunger in place with a 8-32 hex nut.

4) Preparation of the Circuit Board Subassembly: _

a) Insert and solder twenty-four blue wires to the circuit board as shown on page

309-10. Push stripped wire into hole until insulation is flush with solder pad. Bend

wire end over onto the pad, and solder. Cut off any extra.

b) Using 2-56 fillister head screws, attach four ASTRO standoffs loosely to the blank side

of the circuit board - DO NOTTIGHTEN:

c) Insert two light emmitting diodes from the blank side so that the lead with the

double shoulder (see page 309-12) protrudes through the hole marked "X".

DO NOT SOLDER YET.

d) With the assembly jig held ill a vise as shown in page 309-9, fit the circuit board

up to the jig by placing the standoffs in the appropriate holes. Be sure that the

LED's are lined up with the two holes in the jig marked "X".

e) Tighten the four screws, and then solder the LED's in place. Be sure that l_oth

leads of an LED protrude at least 0.025 inch - that isequal to the width of the lead.

! CHG. E.C.O. DAZI'E APPR

Issue ...... 6-15-73 /_J_4: i

!

I 309-3i

NOTE:

In production, it may be easier to tighten the screws with the jig laying on a flat surface -

before the LED's are inserted. Then mount the jig in a vise and mount the LED's.

f) Insert the five data modules into the circuit board. Mate the assembly jig to the circuit

board subassembly and set it down on a flat surface. Solder the data modules to the board.

5) Mount the circuit board subassembly to the faceplate with four 2-56 fillister head screws.

6) Insert the polarizing key between contacts 6 and 7 in the Viking connector. Mount the

Viking connector as shown on page 309-6. Use two 4-40 x 3/8 binder head screws to hold the

connector to the struts. Use six 2-56 fillister head screws to hold the strut covers to the

struts and to_hold the struts to the faceplate. NOTE: insert all eight screws loosely

before tightening any one of them, then tighten the strut covers first.

7) Following the list on page 309-16, solder the eight wire pairs and two single wires to the

Viking connector. The wires must be solderedto the contacts as shown on pages 309-6 and

309-11.

8) Solder two wires to the code switch according to the list on page 309-17. Mount the

code switch subassembly to the faceplate with two 2-56 x 3/16 fillister head screws.

B. Type 9 FPB lnterwiring Subassembly

Following the type 9 Faceplate Box Wiring List on pages 309-18-ff, make all connections

indicated to the FPB rear connector A3. Use shrink tubing on each connection.

C. Final Assembly

1) Slip the FPB key onto the V-Bus subassembly connector brackets, and mount the FPB rear

connector A3 using the two bracket screws. Note the orientation of the key and connector

sho_vn on page 309-6.

2) Remove the four screws holding the top cover plate to the l-cell FPB shell struts, and remove

the top cover plate and overlay clip.

3) Slip the rear connector bracket into the slots provided in the struts and attach the faceplate to

the front using four 2-56 fillister head screws.

4) Replace top cover plate and overlay clip being careful not to pinch any wires.

CHG. E.C.O, DATE J APPR.

Issue .... j 6-15-73 j ,z_,3.,4!j '_ 309-4

[ J ][ I _

I

)RING PLUNGER

C

MOUNTING

:::'!/ ::i__?r F PLATE":' ,}': _ SCREW(41

REAR CONNECTOR :. i_1 ,_:_::]_,i_!% ,

MOUNTING HOLES FOR FUNCTION

CODE SWITCH BRACKET L.

COVER PLATE CODE

iiTITLE

COMPUTERSYSTEMSLABORATORY TYPE 9 FPS ASSEMBLY


ST LOUIS, MISSOURI AePaovlso ENG. DRAWINGNO,MLP

BY FOR GATE

_J/4 PI_OO _O'/9' 7_ ORAWN eY 309-5

ISSUE 6-13-73 ,_uA MACROMODULARPROJECT owpCNANGE i 6-15-73

DATE / OESCRIPTIONNO. dIIIII

TYPE9 FACEPLATE

8.32 HEX NUT ,STRUT COVER

x3/8 BINDER HEAD SCREW

x

:_ PiN "lB"

P,C. BOARD ....

TYPE 3 FUNCTION CODE SWITCH SUBASSEMBLY_-_'""_"--'_'

INTERWIRING SUB-SUBASSEMBLY

KEY

1

PIN 2

NOTE: LEFTWARD.KEYTAB EXTENDS / !_

ONNECTOR BRACKET SCREW

US SUBASSEMBLY

TITLE


i WASHINGTON UNIVERSITY TYPE 9 FPB VISCERAL SUBASSEMBLY

; ST LOUIS, MISSOURI APPROVEO i!E.G.: DRAWING NO,FOR , OA'_E L N_LP

i ISSUE "z_ _A PROD j_o-/_1.7,3 ....... 309-6I 6-_s-. ,_ uA MACROMODULAR PROJECT : owp ,

0 @ ®- I

V : A B C D EL FRONT

O0 ®®@OO'®® @

%1

o©o ",,o o oooo 1_°°°- 43 43H__3oooo 6°°°10 o

5 56 67 7 BACK

· 9 910 10

m__,o_0___®__O___®__0_ v.,_WIT'CH A,SzC/,_Ly I

COMPUTER SYSTEMS LABORATORY MACROMODULAR PROJECTWASHINGTONUNIVERSITY

ST.LOUIS,MISSOURI TITLEi TYPE 9 FACEPLATEi

I COMPONENT ORIENTATION!·,,o,,0 ,.o o,.,,,,.o.o.

., .o. o,,. MLP

ISSUES-15-73 .,_,4,4,,_,,./,4 PROD _;-/_-;'$°_/_,_. '309-7I DATE

c...°, °.. °,.,,,,,o. _f"_ [6-15-'73NO.

NOTE ORIENTATION OFCOAXiCONS (15)

1

VIKING,-.. B!Oi -'_/ !I '/ I _

POLARIZING

' O. · :70".'I'I-:"??iTM ':::i

. ..:.:_.....%_?_::, 4;¢:i?i:::¢:i:?.'?;::'::

COMPUTERsYSTEMS LABORATORY MACROMODULAR PROJECTWASHINGTONUNIVERSITY

ST. LOUIS,MISSOURI TITLETYPE 9 FACEPLATE SUB-SUBASSEMBLY

FRONT-VIEW/

APPROVED EHG DRAWSNG HO.

BY FO_ DATE MLP,qs./M PROD ro-/O'7.5 D_,WNBY 309-8

Iss. 6-15-73 ,q,,/,4 DLSCHECKED DATE

C"A.OEOA_E DESC,.PT.O. ,._'(y'No. 6-15-73

BOARD ASSEMBLY JIG

(PART NO. 903)

COMPUTERSYSTEMSLABORATORY MACROMODULAR PROJECTWASHINGTONUNIVERSITY

ST. LOUIS,MISSOURI Tree

I PCBOARDASSEMBLYJIG

AmOVEO ENO D_W._ONO.MLP

BY FOR m DATE

R,,/M PROD 6'/9'7,_ DRAw.By 309-9' GWPIssue 6-15-73 A_vtA

O'IECKED DATE

C.A,OEDA,E D.C,.,T'O" Wr/×_ 6-15-73NO. I

r

l?

//

/-

COMPUTER SYSTEMS LABORATORY , MACROMODULAR PROJECTWASHINGTON UNIVERSITY

ST. LOUIS, MISSOURI TITLEPC BOARD WIRING

!

I APPROVED ENG DRAWING NO.MLPBY I FOR r DATEI 309-10

,/_',,./.,4 PROD _-/9-73 DRAWNmYGWPIss. 6-15-73 ,q',J,4

C_KE_ DATECHANGE DATE DESCRIPTION 6- I 5-?3NO.

i i

I

, SHRINK TUBING MUST BE CUT EVEN WITH TOP OF PINS

AFTER SOLDERING WIRES MUST BE PL

DOWN THE PIN AND BROUGHT OUT LYING FLAT

ON THE CONNECTOR

WIRES FROM PENS ON ROW MUST BE PI

BETWEENPINSONROW,. NOTE'.

WHEN SOLDERING CARE MUST BE TAKEN NOT TO IHJUR_

THE WIRE INSULATION PLACED BETWEEN THE PINS ON'

ROW A.

T_TLE

" COMPUTER SYSTEMS LABORATORY VIKINGCONNECTOR:WIRINGINSTRUCTIONSWASHINGTON UNIVERSITY

i

ST, LOUIS, MISSOURI *PPnOVgD ENG, i DRAWING NO,

_1' FOR / DATI[ MLP ' 309-11

,SSUE6-,s-7s "_"/'_ MACROMODULAR PROJECT R,,JA PROD ]]----"/9';'$ ....DLS*"' ICNA NGII[ I

I I

i

c)

I

,]',i ! I

' ' INDEXNOTCH

.I .,_------_DOUB LE SHOULDER

\

COMPUTER SYSTEMS LABORATORY MACROMODULAR PROJECTWASHINGTONUNIVERSITY

TITLEST. LOUIS, MISSOURI

LED ORIENTATIONi

APPROVED ENGA DRAWING NO.LPfly POll DATE DU'_' _"_- 1 3

/t_,./A PROD _-19'75 o_w. BYIssue 6-15-73 "_'.]"_ MAC

CHA.OE DaT. DESCll,M,O. c_ !DATE6_15_73NO. I Ii i

I

G-LIST,1 LN=I

[WIRE LIST FOR COAXICONSE

>>>>>>>>>>>>_>7>

5Gi5 [ BLUE>>>>>>>>>>>>>>2>

' 5Gl_ E BLUE>>>>>>>>>>>>>>_>

5G15 [ BLUE>>>>>>>>>>>>>>P>2G1 [ BLUE1Gl [ WHITE>>>>>>>>>>>>>>7>

2G7 [ ORANGE1G7 [ YELLOW>>>>>>>>>>>>>>7>

2G_ [ BROWN° 1G4 £ WHITE

>>>>>>>>>>>>>>_>2GlO [ ORANGE

1GlO [ RED>>>>>>>>>>>>>>_>2G13 [ SLATE1G13 [ RED>>>>>>>>>>>>>>>>5G12 [ BLUE />>>>>>>>>>>>>>>>

5Gll [ BLUE>>>>>>>>>>>>>>2>

1G12 [ RED2G12 E BROWN>>>>>>>>>>>>>>7>XGX5 C YELLOW

2G15 [ ORANGE>>>>>>>>>>>>>>_>

'1G9 E HEU2G9 £ BLUE>>>>>>_>>>>>>>7>1G6 C YELLOW2G6 E BLUE>>>>>>>>>>>>>>_>

5G10 [ BLUE>>>>>>>>>>>>>>_>

1G5 [ WHITE2G3 [ GREEN>>>>>>>>>>>>>>7>1Gl! E RED2511 [ GREEN>>>>>>>>>>>>>>_>1Gl4 [ YELLOW

2G1_ [ BLUE>>>>>>>>>>>>>>_>1G8 [ YELLOW2G8 E GREEN

>_))_)_))_7) CHG E.C.O. DATE APPRiG5 E WHITE2G5 £ SLATE Issue 6-15-73 R_,/A>>>>>>>>>>>>>>2>

.. 309-13

G-LIST,2 LN=72

ZG2 [ WHITE262 [ ORANGE>>>>>>>>>>>)>>P>309 [ BLUE>>>>>>>>>>>>>>_>568 [ BLUE>>>>>>>>>>>>>>P>5G7 [ BLUE>>>>>>>>>>>>>>_>566 [ _LUE>>>>>>>>>>>>>>_>555 [ BLUE>>>>>>>>>>>>>>_>5G_ [ BLUE>>>>>>>>>>>>>>_>5G5 [ BLUE>>>>>)>>>>>>>>P>5G2 [ BLUE>>>>>>>>>>>>>>P>5Gl [ BLUE>>>>>>>>>>>>>>P>

[[G-LIST

309-14

[L

H-LZST,1 LN:I

[WIRE LIST FOR CIRCUIT BOARD HOLES[ x

>>>>>>>>>>>>>>3>

12H [BLUE>>>>>>>>>>>>>>3>

17H [BLUE>>>>>>>>>>>>>>3>

21H [BLUE>>>>>>>>>>>>>>3>

8H [BLUE>>>>>>>>>>>>>>3>

9H [SLUE>>>>>>>>>>>>>>_>

22H [BLUE>>>>>>>>>>>>>>_>13H [BLUE>>>>>>>>>>>>>>3>18H [BLUE>>>>>>>>>>>>>>_>5H [BLUE>>>>>>>>>>>>>>_>

_H [BLUE>>>>>>>>>>>>>>_>

lOH [BLUE>>>>>>>>>>>>>>_>15H [BLUE>>>>>>>>>>>>>>3>19H [BLUE

>>>>>>>>>>>>>>_>6H [BLUE>>>>>>>>>>>>>>3>

7H [SLUE>>>>>>>>>>>>>>_>

20H [BLUE>>>>>>>>>>>>>>_>lIH [BLUE>>>>>>>>>>>>>>3>

16H [BLUE>>>>>>>>>>>>>>3>

2H [BLUE x>>>>>>>>>>>>>>_>

iH [BLUE>>>>>>>>>>>>>>3>2_H [SLUE>>>>>>>>>>>>>>3>

23H [BLUE>>>>>>>>>>>>>>3>i_H [BLUE>>>>>>>>>>>>>>3>

5H [BLUE>>>>>>>>>>>>>>)>

[

EH-LISTCHG; E.C.O. DATE i APPR.

Issue -- 6-15-73 d_A

309-15

V-LIST,! LN=I

[WIRE LIST FOR VIKING CONNECTOR[

>>>>>>>>>>>>>>m>

2AV [ WHITE2BV [ BLUE

>>>>>>>>>>>>>>3>ZAv [VIOLET1BV [ ORANGE>>>>>>>>>>>>>>3>7AV [ YELLOW7BV [ _LUE>>>>>>>>>>>>>>3>

qAV [ YELLOW_BV [ BROWN>>>>>>>>>>>>>>2>3AV [ RED5BY [ SLATE>>>>>>>>>>>>>>_>8Av [ WHITE

8BV [ SLATE>>>>>>>>>>>>>>3>

9BV [ _LUE

9AV £ WHITE>>>>>>>>>>>>>>3>

iOBV [ GREENIOAV [ WHITE>>>>>>>>>>>>>>3>

5AV [ YELLOW>>>>>>>>>>>>>>2>

5BV [ YELLOW>>>>>>>>>>>>>>3>

[

IV-LIST


Issue 6-15-73 ._J_

I309-16

S-LIST,1 LN:i

[WIRE LIST FOR CODL SWITCH[

_>>>>>_>>>>>>>_>

.2S1 [BLUE[NORMALLY UPEN[LABELED .NO"

>>>>>>>>>>>>>>_>

iS! [¥LLLOW[COMMON[L_BELED"C" o

>>>>>>>>>>>>>>_>

[IS-LIST

/

iCHG. E.C.O. DA_E APPR'Issue ---- 6-15:73 ,_,,./_

309-17

FPI9WL,1 LN:I

[TYPE 9 FACEPLATE UOX WIRING LIST[

>>>>>>>>>>>>>>_>

#1A512H [BLUE

#

>>>>>>>>>>>>>>_>2A517H [BLUE

#>>>>>>>>>>>>>>>>5A5

21H [BLUE#

>_>>>>)>>>>>>>)>

4A5BH [BLUE

>>>>>>>>>>>>>>_>

5A59H [BLUE

>>>>>>>>>>>>>>_>6A322H [BLUE

#. >>>>>>>)>>>>)>_>

7A515H [BLUE

#>>>>>>>>>>>>>>_>

8A31BH [BLUE

#>>>>>>>>_>>>_>_>

9A5

5H [BLUE#

>>>>>>>>>>>>)>_>

lOA56H [BLUE

#>>>>>>_>>>>>_>_>

llA32AV [ WHITE

#

12A52BV [ BLUE

#

15A5

iAV [VIOLET CHG.!E.C.O. ! DATE I APPR# Issue r 6-'15-73 l-'t_JA

l_A31BV [ URANGE i

i i 309-18

FPTgWL_2 LN=72

15A57AV E YELLOW

#16A57BV [ BLUE

#

17A31OH [BLUE

#>>>>>>>>>>>>>>_>1BA315H [BLUE.

#>>_>>>>>>>>>>>_>19A319H [BLUE

#>>>>>>>>>>>>>>_>20A36H [BLUE

#>>>>>>>>>>>>>>_>21A37H [BLUE

#>>>>>>>>>>>>>>_>

22A320H [BLUE

#>>>>>>>>>>)>>>_>23A5llH [BLUE

#>>>>>>>>>>>>>>>>2_A316H [BLUE

#

25A32H [BLUE

#>.>>>>>>>>>>>>>_>

26A5IH [BLUE

,_ />>>>>>_>>>_>))_>27A5_AV [ YELLOW

#28A3_BV [ BROWN

#

29A35AV E RED

309-19

FPTgWL,3 LN:163

30A33BV [ SLATE

#>>>>>>>>>>>>>_>

31A33G15 [ BLUE

#>>>>>>>>>>>>>>_>32A35G1_ [ BLUE

>>>>>>>>>>>>>>_>

53A38AV [ WHITE

34A38BV [ SLATE

#>>>>>>>>_>>>>_>35A32Si [BLUE

o .

>>>>>>>>>>>>>>P>36A35Gi3 [ BLUE

#>>>>>>>>>>>>>>>>

57A524H [BLUE

>>>_>>>>>>>>>>_>38A5

2,3H[BLUE \#

>>>>>>>>>>>>>>_>39A32G! [ BLUE

#_OA3iGi [ WHITE

>>>>>>>>>>>>>>>>

_1A32G7 [ ORANGE

#42A31G? [ YELLOW

#>>>>>>>>>>>>>>_>

_5A3254 [ BROWN

#44A31G4 [ WHITE

>>>>>>>>>>>>_>_>

309-20

FPTgWL,_ LN=25_

_5A32GlO £ ORANGE

#%6A51GlO [ RED

#>>>>>>>>>>>>>>>>47A52G15 [ SLATE

#_8A51G13 E RED

#>>>>>>>>>>>>>>_>

49A55G12 [ BLUE

#

50A35G11 [ BLUE

#>>>>>>>>>>>>>>>>

51A51G12 [ RED

52A32G12 £ BROWN

#>>>>>>>>>>>>>>_>55A31515 [ YELLOW

#5_A52G15 C ORANGE

#>>>>>>>>>>>>>>>>

.55A3159 £ RED

#56A52G9 £ BLUE

#>>>>>>>>>>>>>>P>57A31G6 E YELLOW

#58A32G6 E BLUE.

>>>>>>>>>>>>>>_>59A33GlO [ BLUE

#>>>>>>>>>>>>>>>>60A5 CNO CUNNECTION

#>>>>>>>>>>>>>>_>

309-21

FPT9WL,5 LN=345

61A31G3 C WHITE

#62A32G3 C GREEN

#>>>>>>>>>>>>>>>>6_A59BV £ BLUE

#64A59AV [ WHITE

#>>>>>>>>>>>>>>>>65A3ZOBV [ GREEN

#66A3IOAV [ WHITE

#>>>>>>>>>>>>>>_>67A31Gll [ RED

#68A52Gl[ [ GHEEN

#

69A31GI_ [ YELLOW

#70A3

2G1_ C BLUE#

>>>>>>>>>>>>>>_>71A31G8 [ YELLOW

#72A52G8 C GREEN

#>>>>>>>>>>>>>>_>

73A31G5 £ WHIT_

#f A32G5 [ SLATE

#>>>>>>>>>>>>>>_>

75A3

1G2 £ WHITE#

76A52G2 [ ORANGE

#>>>>>>>>>>>>>>_>

[THREE WIRES ARE SOLDERED TO PIN 7745

309-22

L

FPTgWL_6 LN=_36'

" 77A314H [BLUE5AV E YELLOW5BV [ YELLOW

#> > _> ;>>;)> ;) > >>;) ;),_>78A3 [NO CUNNECTION

#>>>>>;)>>>>>>>>;_>75A35G9 E BLUE

#>>)>>>>>>>>>>>P>80A53G8 E BLUE

#>>,_>>>>>,_))>>;>,_>

[TWO WIRES ARE SOLUERED TO PIN 8lA381A31'S1 EYELLOW3H r BLUE

#

82A3357 E BLUE

#>>>>>>>>>>>>>>._>85A3;5G6 E BLUE

#>>>>>>>>>>>>>>,_>8_A3355 r. BLUE

#>>>>>>;)>>>;_>>;),_>85A33G4 C BLUE

#>;)>>>>;)>>>)>;);),)>86A3553 E BLUE

#>>>>>>>>>>>>>>;)>87A3

352 E BLUE#

>;)>>;_>;>>;_>) >>;_>;_88A3 ·3G! E BLUE

# />>>>>>>>>>)>>>>>

. 89A5 ENO CUNNECTION#

90A5 ENO CUNNECTION#

[FPTgNL

3O9-23

COMPUTERSYSTEMSLABORATORY J3 10jWASHINGTON UNIVERSITM


i i i

PAgE T IT LE CHANGEJ I

310-1 Title Page ISSUE

310-2 Parts List

310-3

thru Introduction - Assembly Procedures

310-5

310-6 T_r'.__I0_Faceplate Box Assembly

310-7 Type 10 Faceplate Sub-subassembly Front View

310-8 Type 10 Faceplate Sub-subassembly Rear View

310-9 Wiring Instructions: Viking Connectors Fl, F2

31 0-10 Type 10 Faceplate-connector Orientation

310-11 Type I0 FPB Rear Connector Block' Assemblies

310-12

thru Type 10 FPB Wiring List

310-24

ii i i

cHG. E.C.O. DATE APPR. CHg. ,E,C.O. I DATE APPR.i cHG.i E.C.O., DATE APPR. Ii

Issu_ , , 5-29-73 ,R J_J'i ii

I

I

, i


310-1

TYPE 10 FACEPLATE BOXPARTS LIST

QTY. I C.S. L'. DOC. PART'I2 i 300.0 _ FPBRearConnector /

1' 300.2 2CellFPBShell [

2 300.5-2 FPB Connector Bracket

6 300.5-3 Connector Bracket Screws

24 300.5-4 Astro Standoff

1 300.5-5 FPB Key I1 300.5-6 V-Bus Subassembly [

2 300.5-19 Connector Strut Type 1

2 300.5-20 ,Connector Strut Type 2

4 300.5-21 Strut Cover

1 300.5-22 Interlock Pin

1 300.5-23 Type 10 Filler Strip

1 300.5-24 Type 10 FPB Overlay

1 300.5-25 Type 10 Faceplate

o 6 Astro 348-7012-1Connector

2 .... Viking Connector No. 3VHI0/IJN5

4 Switches CK7101 with Lock Nuts and Lock Washers

2 Monsanto No. MV5023 Light Emitting Diodes with Mounting Hardware

4 4-40 x 3/8Binder Head Screw

I 88 -, · 2-56 x 3]16Fillister Head S.S. Machine Screwst

6 H.H. Smith No. 1412-4 Locking Terminal Lug[

[ -- Wire(See 301-10 ff for Color Code)[

-- 1/16 inch Shrink Tubing

222 Astro Male Contacts

2 Viking Polarizing Key No. 091-0071-000I[ , i i i

CHG. E.C.O. DATE APPR. CHg. E.C.O. DATE APPR. iCHG. E.C.O. DATE APPR.

Issue 5-29-73 /:_UA


310-2 f

'INTRODUCTION

This document (310) describes the assembly of the Type 10 Faceplate Box. A summary list of

all required parts, including subassemblies specified in other documents, is given on page 310-2.

The general specification on wire preparation and wiring procedures (CSL Document 300.0)

must be followed together with the color code information supplied by the wire lists for the Type 10.

FPB. (Pages 310-12 thru 310-24).

ASSEMBLY PROCEDURES

A. Type 10 Facephte Sub-subaSSembly

11 Install a Viking Polarizing key between pins 8 and 9 in each of the Viking connectors (No.

3VH10/I JN5) as shown in drawing No. 310-7. Mount Viking Connectors onto a Type 1

and Type 2 Connector Strut as shown in drawing Nos. 310-8 and 310-10, using 4-40 x 3/8

screws. (Note the orientation of struts and connectors.) Mount Strut Covers (part No.

300.5-21 ) using two 2-56 x 3/16 screws for each cover. (See drawing Nos. 310-10 and

310-8.) Place the Interlock Pin (part No. 300.5-22) into the two Type 2 Connector Struts.

(See drawing No. 310-8). Mount assemblies onto Type 10 Faceplate using 2-56 x 3/16

screws as shown in drawing No. 310-7.

2. Mount Astro Standoffs (part No. 300.5-4) onto Type 10 Faceplate (part No. 300.5-25) using

2-56 x 3/16 screws (see drawing No. 310-10). Apply a small quantity of Locktite to each

of these screws before assembly and tighten firmly. Mount Astro Connectors No. 348-7012-1

and ground lugs on to Astro Standoffs using 2-56 x 3/16 screws. (See drawing No. 310-8 for

correct orientation of ground lugs and connectors).

CHG. E .C.O. DATE A F'I>I_.

Issue 5-29-73 /:_ J./t

L

310-3

° 3. Thread switches (No. CK7101) with lock nuts and lock washers into Type 10 Faceplate as shown

in drawings 310-8 and 310-10. Switch lever must protude approximately. 130 inch. (See

drawing No. 310-7). Securely tighten the lock nut and washer against the Type 10 faceplate.

At this time check for free operation of switches.

4. Remove the backing from the Type 10 Faceplate Overlay (part No. 300.5-24) exposing the

adhesive. Place on Type 10 Faceplate as shown in drawing No. 310-6, carefully aligning all holes.

5. Two LED retention flanges should now be pressed by hand into the specified holes (drawing

No. 310-6) with the flanges to the front. The two LEDs shall then be inserted into the retention

flanges from the rear until they snap securely into place, with Pin 1 and Pin 2 aligned

horizontally. Pin 1, or the double.shouldered lead, shall be placed on the left side of theType

10 Faceplate as viewed from the front. The next step is to press on the rear locking ring.

This is done by centering it over the rear of the retention flange and pressing straight down

until the ring touches the metal surfac& (Notice the locking ring is tapered. The ring must

be installed with the large end down toward the metal.)

B. Type 10 FPB Interwiring Sub-subassembly

1. Connectors D1, D2, D3, D4, D5, D6

Following the Type 10 FPB Wiring List, crimp the wire pairs in the Astro 348 male contacts and

insert the contacts into the Astro'348 connector following the directions supplied with the

connectors. Terminate the free end of these wires to their respective terminals on connectors

A3 and A5. Connectors A3 and A5 are not as yet mechanically attached to any mounting

hardware.

C. Connector F1 and F2

1. Following the Type 10 FPB wiring list interconnect F 1, F2, A3 and'A5. Drawing No. 310-9

indicates the correct method of wiring to and insulating terminals and connectors F 1 and F2.

i 'CHC,. E'.C.O. .DAI'E" A'PPR.

Issue 5-29-73 : ,_/'/4 '

310-4

2. All unused pins Of F 1, F2, A3 and A5 must be covered with shrink tubing.

D. Light Emitting Diodes L1 and L2C

1. Following the TyPe 10 FPB Wiring List, wire wrap and solder to LED terminals then cover with

shrink tubing and wire to the FPB Rear Connector A5 and to Astro Connector D6. Note that

1L1 and 1L2 (Double Shouldered Pins) are tied together and a single wire then goes to D6.

Note orientation on drawing No. 310-8.

E. Switches S1, S2, S3, S4

1. Following the Type 10 FPB Wiring List, wire Switches to the FPB Rear Connectors A3 and A5.

See drawing No. 310-8 for orientation.

F. Assembly of Rear Connectors A3 and A5

1. Slip the FPB Key onto the V-bus Subassembly Connector Brackets and mount the FPB Rear

Connector A5 using two Connector Bracket Screws. Note the orientation on drawing No.

310-11.

2. Mount Connector A3 and Type 10 Filler Strip to Connector Brackets (part NO. 300.5-2.) Seed

drawing No. 310-11.

G. Final Assembly (See page 310-6)

1. Remove the screws holding the topmost and bottommost Cover Plate pair to the 2-cell FPB

Shell Struts. Remove these Cover Plates with their respective Overlay Clips.

2. Slip the Rear Connector Blocks of the two connector assemblies into the slot provided

in the Struts for the Connector Bracket. See drawing No. 310-11. Replace Cover Plate

pair and attach the Type 10 Faceplate to front asing the remaining 2-56 screws.

3. Take care to assure that the wires are not pinched in this assembly.

clio. _.c._i....... .6,_;F'"I A'f;,'_7Issue 5-29-73 ,/_ _/._'

i

II

310-5

TYPE 10 FACEPLATE OVERLAY

(PART NO.LAoToEsO_4ERL'A_ -- OVERLAY CLIP

Y _

CALL COVER PLATE

i,,_ o {PART"O.*00,-7_

D -

rmr_r: ADRS UAR lC DW RMB _:

I _v-_ _ _ _ _, _ i COVER PLAT

_[ R_ ..................... i PAIR

Ij'.:::.__I........'.--..*x,_.....................................................',L.E.D. RETENSION FLANGES

I

TITLE

COMPUTER SYSTEMS LABORATORYTYPE t0 FPB ASSEMBLY


ST. LOUIS. MISSOURI APPROVED ENG. DRAWING NO.ADR

BY FOR , OAT[

R ,-/,4 PROD S-,_o-75 ORA...¥ 3,0-6issue 6_3_73 ,'_,./,4 MACROMODULAR PROJECT o,.s

CNECKE DATE

CHANGE ,_. ,,_,_ 6'_ 3-73NO , DATE DESCRIPTION

I II

3/16 x 2-56 FILLtSTER HEAD

STRUT SCREWS (4)

3,,,,x__s,P,LLISTER.EADSCREWSFOR-- r }!ASTRO STANDOFFS (24) _ i ?'_;_ :::?: ';i, '_

_ViKIHG POLARIZING KEY/

Ce '_· _

TYPE t0 FACEPLATE , _'-

(PART NO. 300,5-25) _ /

I:_ .. / VIKING POLARIZING KEY/ir ' ' /

r:.::

?e e et_- ' "::t' '_ _"_ --"' " -- SWITCH LEVERS MUST NOT EXTEND OUTWARD

?...... ._.____ MORE THAN .13Q INCH

TITLE

COMPUTER SYSTEMS LABORATORY TYPE 10 FACEPLATE SUB-SUBASSEMBLY FRONT VIEW

: WASHINGTON UNIVERSITY

ST. LOUIS, MISSOURI APPROVED ENG. DRAWING NC).I ADR

I BY Fg_ DATE: 310-7

ISSUE R-3-73 ,_ UA MACROMODULAR PROJECT _,../.4 PROD ,_'_O-?$j .......DLSCNECKE . DATE

¢,ANoe .,.;_<2NO. DATE DESCRIPTION 6--3 - 73I ,

LDER LUG NOTE ORIENTATION )

STRUT COVI

(PART NO. 300,5-21

f /Pm 1] SAME ORIENTATION FORpROW A PIN 1

"'""-..-. /v D2, D3, D4, DS, ond D6

CONNECTOR F1 _,: _PIN4 i

'i

iNTERLOCK PIN 1

(PART NO. 300.5-22) D2

ROWA PINI _CONNECTOR F2

D6

I I

I PIN 1PiN I

SAME ORi_t4TAT_ON

FOR S2, S3, AND S4 d PIN 2

J PiN 3

k

52--

S4

........ I

TITLE


WASHINGTON UNIVERSITY TYPE 10 FACEPLATE SUB-SUBASSEMBLY REAR VIEW

ST. LOUIS, MISSOURI APPROVED :ENG. GNAWING NO.I

J_y FOR : DATE ADR

,q J4 PROD G-20-75:o.^..DY s_o-8iSSUE Ai 'r_ '_ ud MACROMODULAR PROJECT , D_.s i

i CHECKED DATE

CHANGE _NO. DATE DESCRIPTION _; _' : 6--6--7_

· ' I i

WIRES FROM PINS ON ROW A MUST BE PLACED BETWEEN PINS OH ROW B

AFTER SOLDERING WIRES MUST BE SHRINK TUBING MUST BE CUT EVEN WITH TOP OF PINS

DOWN THE PIN AND BROUGHT OUT LYING

FLAT ON THE CONNECTOR

NOTE:

WHEN SOLDERING CARE MUST BE TAKEN NOT TO INJURE THE WIRE INSULATION PLACED BETWEEN THE PINS (_q ROW B, f

A SOLU'TJON WOULD BE TO SOLDER WIRES ON ROW B BEFORE PLACING WIRES BETWEEN PINS.

TITLE

COMPUTER SYSTEMS LABORATORY w_RINO INSTRUCTIONS: VIKING CONNECTORS Fl, F2

WASHINGTON UNIV_RSl TY

ST. LOUIS, MISSOURIAPPROV_D ENG, DRAWING NO,

DY FUR DATI[ AOR

R_/_[ PROD 6.20.75 _.AW..v 3t0-9

,ssuE ____,_ ._,./4 MACROMODULAR PROJECT pL[ I

CHANGE _HJ[CKEO(._4-//_r/_ ! DATE

~o. O^TE D_sca,Pr,o~ ..._/_x/J 6

I

3 '8 x 4-,(0 BINDER HEAD SCREWS (41 --

TYPE 1 STRUT

(PART NO. 300.5.-191

_ _tJ,_____AST RD STANDOF F(PART NO. 300.5--4)

TYPE 2 STRt _ I _ t ,

(PAR, T NO. 300.$-20)

41b

INUT

1 STRUT

(PART NO, 300 S.- 9)

STRUT COVER

(PART NO, 300.5-.21)

TITLE

i COMPUTER SYSTEMS LABORATORYJ WASHINGTON UNIVERSITY TYPE l0 FACEPLATE - CONNECTOR ORI£NTAIION

I ST. LOUIS, t_JSSOU_:_ APPROVED ENG. DRAWING NO.

--- ADR i' DY F(_R DATE .

·J _ J ,4 PROD (,-2o-75 ....... ! 3,o--(o,S_oE (..3..,_ _UA MACEOMODULAR PROJECT . D,_s

_HECKEO OATE

C.,,,,.GE F_',J'::'_ o.-3._T_NO ` DATE DESCRIPTION I C

; "'r-::> FPB REAR CONNECTOR

I_ A3/

PiN 90 _PIN !

' I: _PIN 2'YPE 10 FILLER STRIP

{PART NO. 300,5-23

FPB REAR CONNECTOR

AS

i

FPB KEY

NOTE ORIENTATION

(KEY TAR EXTENDS LEFTWARD)

V-BUSSUBASSEMBLY

TITLE

COMPUTER SYSTEMS LABORATORYWASHINGTON UNIVERSITY TYPE 10 FPE REAR CONNECTOR BLOCK ASSEMBLIES

ST LOUIS, MISSOURI APPROVED ENG.AD R DRAWING NO'

BY FOR DATE 310-]1

,l_v/4 ' PROD _'J0-73 ............. ,-3-_ _ u A MACROMODULAR PROJECT OLS

CHECKED DATE

CHANGE ._ 6_3-73NO. DATE DESCRIPTION

FPTIOWL,1 LN=I

[ TYPE TEN FACEPLATE BO X WIRING LIST[[[

>>>>>>>>>>>>>>>

#lA33AF1E RED

#5A3 E TWO WIRES3BFZE SLATE

#>>>>>>>>>>>>>>>

2A3

2AFl[ WHITEff

5A3 ETWO WIRES2BF[E BLUE

#>>>>>>>>>>>>>>>

3A35AFl[ WHITE

#6A3 [TWO WIRES5BF1£ GREEN

#'>>>>>>>>>>>>>>>

4A34AFIE YELLOW

#6A3 [TWO WIRES

_BFi[ BROWN#

>>>>>>>>>>>>>>>

[[ TWO WIRES ARE SOLDEREU TO PTN 7A3[

7A32BF1£ BLUE2BF2£ BLUE

P>>>>>>>>>>>>>>>

[[ THREE SIX INCH WIRES WITH GROUND LUGS SOLDERED TO PIN 8A3[

8A3D[

102#

>>>>>>>>>>>>>>>9A3 'CHG.! E.C.O. DATE APPR

1904 £ BLUE I_ue 5-29-73 ,Z_c,/_#

10A318D4 £ VIOLET

#>>>>>>>>>>>>>>>

310-12

1 LN=72

1].431901 [ BLUE

12431801 E VIOLET

>>>>>>>>>>>>>>>13436D4 [ VIOLET

1443704 [ ORANGE

>>>>>>>>>>>>>>>15456DI [ VIOLET

16A3701 [ ORANGE

>>>>>>>>>>>>>>>17A5$7D6 £ ORANGE

1BAS5_D6 [ YELLCW

>>>>>>>>>>>>>>>194_37D3 [ ORANGE

20435603 E YELLOW

>>>>>>>>>>>>>>>21A5

3106 [ SLATE

22433006 [ YELLOW

>>>>>>>>>>>>>>>25453105 £ SLATE

2q455005 [ YELLOW

>>>>>>>>>>>>>>>25A_240_ E ORANGE

26A_2_06 [ RED

>>>>>>>>>>>>>>>2740

310-13

FPTiOWL,3 LN=163

2403 r. ORANGE

28A323D3 [ RED

#>>>>>>>>>>>>>>>29A332D6 Ii RED

#30A333DG E BLUE

#>>>>>>>>>>)>>>>31A332D3 r RED

#32A33303 E BLUE

#>>>>>>>>>>>>>>>33A326D6 I: BROWN

#34A3

f 25DG I: RED#

>)>>>>>)>>>)>>>35A326D3 E BROWN

#36A325D3 E RED

#>>>>>>>>>>>>>>>37A328D6 E SLATE

#38A327D6 [ WHITE

#>>>>>>:>>>>>>))>39A32AD3 r SLATE

#q.OA327D3 t WHITE

#)>>>>>>>>>>>>>>41A32106E BROWN ,'

#42A320DE, E YELLOW

#>>>>>>>>>>>>>>>43A321D3 I: BROWN

310-14

FPTiOWL,_ LN=25_

#_qA320D3 E YELLOW

>>>>>>>>>>>>>>>_5A31606 [ YELLOW

#_6A31TOG [ GREEN

#>>>>>>>>>>>>>>>47A316D3 [ YELLOW

#qBA31703 E GREEN

#>>>>>>>>>>>>>>>q9A3.13D6 [ BROWN

#50A3

10D6 [ WHITE#

>>>>>>>>>>>>>>>

51A3lZD3 [ BROWN

#52A3[OD3 [ WHITE

* # f

>>>>>>>>>>>>>>>

53A313D6 [ GREEN

5aA312D6 [ WHITE

#>>>>>>>>>>>>>>>55A31303 [ GREEN

#56A312D3 [ WHITE

#>>>>>>>>>>>>>>>57A39D6 [ ORANGE

#58A38D6 [ WHITE

#>>>>>>>>>>>>>>>

59A3 i9D3 [ ORANGE

ff

31_15

FPTIOWL,5 LN=3q5

60A38D3 [ WHITE

#>>>>>>>>>>>>>>>

61A31_D6 [ RED

#62A315D6 [ GREEN

>>>>>>>>>>>>>>>

63A314D3 [ RED

#6_A315D3 [ GREEN

#>>>>>>>>>>>>>>>'

65A336D2 [ YELLOW

#66A3

j 37D2 [ ORANGE#.

>>>>>>>>>>>>>>>6TA33002 [ YELLOW

#68A331D2 [ SLATE

#.>>>>>>>>>>>>>>>

69A33202 [ RED

fl70A33302 [ BLUE

#>>>>>>>>>>>>>>>

71A323D2 C RED

fl72A32_D2 C ORANGE

#>>>>>>>>>>>>>>>73A319D2 C BLUE

#7qA318D2 [ VIOLET

#>>>>>>>>>>>>>>>.

75A36D2 [ VIOLET

#76A3

310-16

FPTiOWL,6 LN=_36

7D2 [ ORANGEfi

>>>>>>>>>>>>>>>[[TEN WIRES ARE SOLDERED TO PIN 77A3[

77A35Di [ YELLOW

"5D2-"E'---YEEEOW5D3 [ YELLOW504 [ YELLOW5D5 C YELLOW5D6 [ YELLOW1L1 [NOTE-DOUBLE SHOULDERiL2 [NOTE-DOUBLE SHOULDERiAFi [YELLOWiAF2 [YELLOW

#>>>>>>>>>>>>>>>

[[THREE SIX INCH WIRES WiTH GROUND LUGS SOLDER TO PIN 78a3[

/

78A3D4

' D5D6

>>>>>>>>>>>>>>>79A38BF2£ SLATE

#80A38AF2[ WHITE

#>>>>>>>>>>>>>>>81A3

8AFl£ WHITE

82A38BFl[ SLATE

,

>>>>>>>>>>>>>>>83A33AF2[ RED

#88A3 [TWO WIRES3BF2[ SLATE

#>>>>>>>>>>>>>>>84A32AP2[ WHITE

#88A3 [TWO WIRES2BF2E BLUE

#>>>>>>>>>>>>>>> I85A3 I

310-17

FPTIOWL,7 LN=527

5AF2E WHITE#

90A3 [TWO WIRES5BF2[ GREEN

>>>>>>>>>>>>>>>86A3_AF2[ YELLOW

90A3 [TWO WIRES4BF2[ BROWN

#>>>>>>>>>>>>>>>87A32S1

#>>>>>>>>>>>>>>>

[[ CHAIN 89A3 TO THE FOLLOWING[

89A33S11S2 r

I 1S3154

#>>>>>>>>>>>>>>>iA57D6 [ ORANGE

#2A56D6 [ VIOLET

#>>>>>>>>>>>>>>>

3A519D6 [ BLUE

#4A5

18D6 [ VIOLET#

>>>>>>>>>>>>>>>5A5

603 [ VIOLET#

6A57D3 [ ORANGE

#>>>>>>>>>>>>>>>

7A51903 [ BLUE

#

8A518D3 [ VIOLET

#>>>>>>>>>>>>>>>

9A5

28D4 [ SLATE

31_18

FPTiOWL,iO LN=620

#

10A5

27D4 [ WHITE#

>>>>>>>>>>>>>>>

llA5

26D_ [ BROWN#

12A525D_/[ RED

#>>>>>>>>>>>>>>>13A52_D_ [ ORANGE

#lqA523D_ [ RED

#>>>>>>>>>>>>>>>15A533D4 [ BLUE

#16A53EO_ [ RED

#- >>>>>>>>>>>>>>>

17A531D_ [ SLATE

#18A5 °30D_ [ YELLOW

#>>>>>>>>>>>>>>>

19A537D_ [ ORANGE

#20A536D_ [ YELLOW

#>>>>>>>>>>>>>>>21A536D5 [ YELLOW

#22A5 .'37D5 [ ORANGE

#>>>>>>>>>>>>>>>23A531D5 E SLATE

#2_A530D5 [ YELLOW

#>>>>>>>>>>>>>>>25A52_D5 [ ORANGE

#

310-19

FPTlOWL,11 LN=711

26A52SD5 [ RED

#>>>>>>>>>>>>>>>27A532D5 E RED

#28A533D5 E BLUE

#>>>>>>>>>>>>>>>29A59D_ £ ORANGE

#30A58D_ E WHITE

#>>>>>>>>>>>>>>>31A515D_ C GREEN

#32A5I#D_ £ RED

>>>>>>>>>>>>>>>33A513D_ C GREEN

ff3_A51204 [ WHITE

#>>>>>>>>>>>>>>>35A511D_ £ BROWN

#36A510D4 E WHITE

#>>>>>>>>>>>>>>>37A517D_ [ GREEN

#58A516D4 E YELLOW

#>>>>>>>>>>>>>>>39A521D_ E BROWN

#_OA520D_ E YELLOW

#>>>>>>>>>>>>>>>

'_1A525D5 E RED

#_2A5

310-20

FPTlOWL,12 LN=IO02

26D5 [ BROWN#

>>>>>>>>>>>>>>>_3A528D5 E SLATE

#_#A527D5 [ WHITE

#>>>>>>>>>>>>>>>

_5A521D5 [ BROWN

#_6A520D5 £ YELLOW

#>>>>>>>>>>>>>>>_7A516D5 [ YELLOW

#_8A517D5 [ GREEN

#>>>>>>>>>>>>>>>

r _9A52801 [ SLATE

#50A527D1E WHITE

#>>>>>>>>>>>>>>>51A526D1 [ BROWN

#52A525D1 [ RED

#>>>>>>>>>>>>>>>

53A52#D1E ORANGE

#5_A523D1 [ RED

#>>>>>>>>>>>>>>>

55A53701E ORANGE

#56A536D1 [ YELLOW

#>>>>>>>>>>>>>>>

57A531D1E SLATE

#58A53OD1 [ YELLOW

31_21

FPTlOWL,13 LN=1073

, tt>>>>>>>>>>>>>>>594533D1 [ BLUE

#(

604532D1 [ RED

It>>>>>>>>>>>>>>>6145

10D5 [ WHITEIt

6245 x11D5 [ BROWN

It>>>>>>>>>>>>>>>

I 634513D5 [ GREE N

#6_4512D5 [ WHITE

It>>>>>>>>>>>>>>>

6545i, 9D5 [ ORANGE

It66458D5 [ WHITE

It>>>>>>>>>>>>>>>67451_D5 C RED

#684515D5 [ GREEN

#>>>>>>>>>>>>>>>

6945 r7D5 [ ORANGE

It70456D5 [ VIOLET

It>>>>>>>>>>>>>>>

714518D5 [ VIOLET

It724519D5 [ BLUE

It>>>>>>>>>>>>>>>

77432L1 [NOTE SINGLE SHOULDER

#>>>>>>>>>>>>>>>7_45 [ NO CONNECTIUN

It

3 ] 0-22

FPTIOWL,i_ LN:116_

>>>>>>>>>>>>>>>

75A52S3

#

>>>>>>>>>>>>>>>76A5 [NO CONNECTION

#>>>>>>>>>>>>>>>

77A5 [NO CONNECTION'#

>>>>>>>>>>>>>>>7'8A52L2 [NOTE-SINGLE SHOULDER

#>>>>>>>>>>>>>>

79A52S4

#>>>>>>>>>'>>>>>>80A52S2

#>>>>>>>>>>>>>>>

I 81A59BFI[ BLU E

#82A59AFI[ WHITE

#>>>>>>>>>>>>>>>83A59BF2[ BLUE

#84A59AF2[ WHITE

>>>>>>>>>>>>>>>

85A5lOAF1[ WHITE

#86A5IOBFi[ GREEN

fi>>>>>>>>>>>>>>>

87A5lOAF2[ WHITE

#88A5iOBF2[ GREEN

#>>>>>>>>>>>>>>>

[[THREE S'IX INCH WIRES SULDER TO PIN 89A5[

89A52201 [ BLUE2202 [ BLUE

310-23

FPTIOWL,15 LN=1255

22D$ [ BLUE#

>>>>>>>>>>>>>>>[[THREE SI'X INCH WIRES SULDER TO PIN 90A5[

90A522D4 [ BLUE22D5 [ BLUE c2206 [ BLUE

#>>>>>>>>>>>>>>>

[[FPTIOWL

310-24

UNCLASSIFIED

Securit_ Classification ' -

· DOCUMENT CONTROl; DATA _ R & D ....

(Security classification of title, bodyof abstract and indexin E annotation must be entered when the overall report Is clasalfied/IZm. REPORT SECURITY CLASSIFICATIONORIGINATING ACTIVITY (Corporate author) I

t Computer Systems Laboratory I UNCLASSIFIED

Washington University I-b. GROUP - _St. Louis, Missouri I

REPORT TITLE

f

FACEPLATE BOXES, TYPES 5 THROUGH 10

4. DESCRIPTIVE NOTES (iT_,pe of report and inclusive dates)

Final Report 4/1/65 through 12/31/735. AUTHOR(S) (First name, middle initial, lost name)

George L. Bickmore, Editor

6- REPORT DATE 74. TOTAl- NO. OF PAGES 17b. NO. OF REFS

IFebruary,1974 87Sm. CONTRACT OR GRANT NO. 98. ORIGINATOR'S REPORT NUM'BER($)

DOD (ARPA) Contract SD-302b.PROJECT NO Volume IX of Part 2

ARPA Project Code No. 655C. 9b. OTHER REPORT NO(S) (.Any uther numbers that may be assigned

this report)

d. Technical Report No. 38lO. DISTRIBUTION STATEMENT

t' Distribution of this document is unlimited.

I1- SUPPLEMENTARY NOTES 112. SPONSORING MILITARY ACTIVI'_Y

L ARPA - Information Processing

Techniques, Washington, D.C.

19. AaSTRACT

This document contains the necessary procedures and wiring iists for the

assembly of Macro-Module Faceplate Box types 5 through 10.

DD '°' ta73 """'¢"°°'°"""'"'""'"""'¢""! NOV '1' 'I' OlllOi. STS ,o. *-.Y USE. UNCLASSIFIED

g_cuHty Classification

UNCLASSIFIEDSecurity Classification

14. LINK A LINK B LINK C', KEY WORDS

ROLE WT ROLE i WT ROLE : WT

,1Macromodule Faceplate Box

UNCLASSIFIE DSecurity Classification

macromodular computer design, part 2, volume 09, faceplate

Documents