lw-446 triplex mud pump
TRANSCRIPT
TEL: +86-13705425163; FAX: +86-532-82599806 www
39 XING HE RD, INDUSTRIAL YARD LANCUN TOWN, JIMO, QINGDAO, SHANDONG,CHINA
E-Mail: [email protected] SKYPE: oilfieldman2 .pumpparts.cn
HW446 Mud Pump
一、 HW446 Mud Pump TECHNICAL SPECIFICATION
Rated input power 328KW (440HP)
Rated Stroke 320 Stroke/Minute(320SPM)
Stroke 152.4mm (6")
Gear Ratio 4.578 :1
Max. operation pressure 35Mpa
Valve chamber Valve-Over API 4#
Max. liner dia. 6″
Max. liner mud pressure(160 stroke/minute)16.9Mpa
Dia. of suction manifold, 6″ (150#) Flange
Dia. of discharge manifold 3″(900#) Flange
Dia. pinion shaft 95.25 mm(3.75″)
Key 22.174x15.9mm
Dimension:(No included base), 2479X1219X1103 mm
Weight 4463 kg
Qingdao HNA Oilfield Equipment Manufacturing Co.,Ltd
二、 Structure character
HW-440/446 Pump can be widely used in all kinds of works in oil field. When the cylinder liner
specification is 6"-3 1/2", piston structure is recommended and it is suitable for Oil-Well Repair and
shallow-well drilling, etc. When the cylinder liner specification is 3 1/4"-2", axial piston structure is
recommended and it is suitable for high-pressure work.
The Pump stand is constructed of steel plates by welding. Furthermore, because the post weld
annealing treatment is applied to eliminate the internal stress, its strength is high and its steel is good.
Moreover, the strengthening plate structure is adopted in the crank shaft bearing house and the main
bearing house, therefore its strength is high and its steel is good.
The crank shaft is constructed of forgings in balance, and thus it is light in weight and it runs smoothly
without any vibration.
The gear shaft is made of forgings of alloy steel and the herringbone gear as a whole is installed with
medium hardness tooth surface gear on the shaft.
The cross head is made of ductile cast iron by entire cast which thus makes the wear-resistant good.
The guide plate is formed in up- and - down structure which thus can adjust the concentricity by the
gasket in the up or the down gasket.
The hydraulic cylinder is made of alloy steel cast in straight-through type and its volume small and
volumetric efficiency high. Furthermore, the surface of the cylinder has been treated with chemical
nickel-plating to enhance its wear-resistant.
The cylinder liners of the W440/446 pump have a same sized external diameter. The fasten effect is
achieved by the squared cylinder liner pressing cover and the bolt pressing the hydraulic cylinder. The
seal between the cylinder liner and the hydraulic cylinder is achieved by the rubber mat in rectangle.
In the lubrication system, the forced lubricating is adopted. The gear oil pump, which is installed in the
oil rank, transmits the pressured oil, through lubrication lines, into the cross head guide plate and all the
shafts to achieve the forced lubrication and cooling purpose.
三、 Performance parameter table
TEL: +86-13705425163; FAX: +86-532-82599806 www
39 XING HE RD, INDUSTRIAL YARD LANCUN TOWN, JIMO, QINGDAO, SHANDONG,CHINA
E-Mail: [email protected] SKYPE: oilfieldman2 .pumpparts.cn
Qingdao HNA Oilfield Equipment Manufacturing Co.,Ltd
HW-446 Performance
Liner Size, inches
Rated Pressure, psi
Pump Speed Input Power
6
1,027
5-1/2
1,222
5
1,479
4-1/2
1,710
4
2,169
3-1/2
2,816
SPM
320
HP
440
661
555
Displacement, GPM
459 397
313
240
270
220
170
120
70
380
320
260
200
200
551
441
330
220
110
463
370
278
185
93
382
306
229
153
76
335
273
211
149
87
264
215
167
118
69
202
165
127
90
52
Volume/Stroke, gallons
2.203
1.851
1.530
1.239
0.979
0.750
Ratings are based on 90% mechanical efficiency and 100% volumetric efficiency.
Mechanical Efficiency η=90%,Fill factor α=100%,Volumetric Efficiency:100%
TEL: +86-13705425163; FAX: +86-532-82599806 www
39 XING HE RD, INDUSTRIAL YARD LANCUN TOWN, JIMO, QINGDAO, SHANDONG,CHINA
E-Mail: [email protected] SKYPE: oilfieldman2 .pumpparts.cn
Qingdao HNA Oilfield Equipment Manufacturing Co.,Ltd