luxury home application
TRANSCRIPT
Grundfos — a world-wide supplierGrundfos offers an efficient world-wide service network. Experienced service technicians and all necessary spare parts are available at short notice in all corners of the world.
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
GRUNDFOS Canada Inc.2941 Brighton RoadOakville, Ontario L6H 6C9 CanadaTelephone: 905 829 9533Fax: 905 829 9512
Bombas GRUNDFOS de Mexico S.A. de C.V.Boulevard TLC #15 Parque Stiva Aeropuerto Apodaca, N.L. Mexico 66600 Telephone: 52 81 8144 4000Fax: 52 81 8144 4010
GRUNDFOS Pumps Corporation17100 West 118th TerraceOlathe, Kansas 66061Telephone: 913 227 3400Fax: 913 227 3500
www.grundfos.com
GRUNDFOS EZ BOOST™ SYSTEM
Reliable, economical pressure boosting for smaller buildings
• medical offices
• restaurants
• homes
• condos
• irrigation
• grocery
Pressure boosting made EZ
L-EZ-SL-001 3/06 (US)Subject to alterations
However, R. L. Feezer Construction Inc. solves this
problem with Grundfos EZ Boost. According to Gen-
eral Manager Rusty George, “Traditional tank sizes
are dictated because the pressure boosting pump
has to be mounted inside the tank, requiring a large
tank. With EZ Boost’s external installation, we have
many more options for tank selection, so now we
use a round tank that is easier to install, costs less,
and eliminates expensive rework of door jambs.” The
result was a savings to the homeowner in terms of
the cost of the tank and labor.
CASE STORYLuxury home application
Submitted by
Rusty George, General Manager
R.L. Feezer Construction Inc.
Sykesville, Maryland
Central Maryland illustrates a common problem
when it comes to water pressure for larger homes.
The water level in the area’s 6” rock wells is very deep,
and the yields are inadequate to pump from the well
direct to housing fixtures. Therefore a holding tank
becomes necessary. Often the only place to install a
holding tank is in the basement – particularly in the
North East where sub-zero temperatures are common
during winter.
Installing a 600 - 1000 gallon holding tank in a base-
ment presents another problem….how to get a large
32” wide X 62” long X 62” tall, rectangular holding
tank down a flight of stairs that, halfway, turns left at
a landing and through a 30” doorway. Since the tank
is larger than the door’s opening size, the door’s frame
must be widened to fit the unruly holding tank.
To choose the appropriate EZ-Boost system for your application is simple. 1. Determine how much pressure you need at a given flow.2. Find-out how much pressure you have available (inlet pressure).3. Select a pump from the chart that gives you the difference.
Example: Need 15 gpm with a total pressure of 60 psi. My line pressure is 20 psi, therefore Ineed a boost of 40 psi.The correct selection would be a Model 22 BMQE 05A-80.
Additional (boost) pressure required
5 10 15 20 25 30 35 39Flow required in gallons per minute (GPM)
in PSI908070605040302010
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 05A-80
22 BMQE 05B-120
22 BMQE 10C-190
30 BMQE 10C-130
30 BMQE 05B-90
EZ Boost Quick Sizing GuideChoosing the appropriate EZ Boost pump for your application is simple:
1. Determine how much pressure you need at your maximum flow.
2. Find out how much pressure you have available (minimum inlet pressure).
3. Select a pump from the chart that gives you the difference.
Example: I need maximum 15 gpm with a total pressure of 60 psi.
My minimum inlet pressure available is 20 psi, so I need a boost of 40 psi.
The correct selection would be a Model 15 BMQE 05A-110.
Typical EZ Boost residential installation
With EZ Boost there are more tank options
LEZSL001_EZBoostBroch_0306.indd 1 3/20/2006 12:02:14 PM
EZ Boost System solves low water pressureIf your problem is low water pressure, Grundfos EZ
Boost is your solution. Grundfos EZ Boost provides
constant water pressure – even while multiple taps
are on, and is perfect for large residential & light
commercial pressure boosting applications:
• medical offices • restaurants • homes
• condos • irrigation • grocery
• plus many other boosting applications
Grundfos’ EZ Boost is a complete pressure boosting
system that includes pump, controller, tank, mount-
ing brackets, and pressure sensor. Its high-quality
construction and rugged design ensures low-main-
tenance and trouble free operation. EZ Boost can be
installed just about anywhere; it is simple to install
and simple to operate. Additionally, it is competitive-
ly priced when compared to other pressure boosting
alternatives.
Grundfos EZ Boost features:
> Maintenance-free
• Seal-less and self-cooling
> Dry-run protection
• Protects the pump from damage if
the water supply runs dry
> Standard home outlet voltages (single phase)
• All models available in 230 volt and
some models available in 115 volt
> Soft-start
• Prevents water hammer in pipes and
stress on the pump (also minimizes
flickering lights)
> Overload and underload protection
• Slows or stops the pump to protect the
motor during unstable voltage conditions
> Many installation options:
• Wall-mounted • Framed-in
• In-ground • Equipment build-on
• Portable devices
EZ BOOST ™ SYSTEM
Performance curves
0 5 10 15 20 25 30 35 Q [US GPM]
0
40
80
120
160
200
240
280
[ft]H
0
20
40
60
80
100
120
P[psi]
TK
01 3
100
4801
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 10C-190
22 BMQE 05B-120
22 BMQE 05A-80
30 BMQE 10C-130
30 BMQE 05B-90
BMQE60 Hz
Technical data
6
2
5 4 7
31
8Flow: Max. 40 gpm (9 m3/h)Head: Max 300 ft./130 psi (91 m)Fluid temperature: Max. 95°F (35°C)Ambient temperature: Min. 32°F (0°C)Operating pressure: Max. 145 psiInlet pressure: Min. 8 psi Max. limited by operating pressureOperating setpoint: 40 to 100 psi (in 10 psi increments)Sound pressure level: < 74 dB(A) at a distance of 3 ft. (1 m) from the pump. Note: Sound-sensitive installations may require insulation.
Pos.1. Sleeve2. Discharge connection3. Suction connection4. Submersible motor
5. Submersible pump6. Cable entry7. Centering device8. Air vent screw
Wes recommended the Grundfos EZ Boost System
model 22BMQE10-190 which, fortunately, he had in
stock.
On Wednesday morning, Wes stopped by the res-
taurant and found it packed with customers. When
it was convenient he discussed the situation with
the owner who was delighted with the Grundfos EZ
Boost System.
This EZ Boost System
boosted water pressure
from the city’s main from
20 psi to the 60 psi needed
for this restaurant’s soda
fountains and toilets.
Ice cream restaurant application
Submitted by
Wes Blumenauer, CEO
The Blumenauer Corporation
Ocoee, Florida
Wes received a phone call late on a Monday after-
noon from a desperate plumber looking for a pump
to solve a water pressure problem at a Friendly’s Ice
Cream Restaurant in Clermont, Florida.
The first problem was the city’s water main could
only supply 20 PSI to the restaurant. The plumber
said at least 60 PSI was required to operate the soda
machines and flush the toilets.
The second problem was that the restaurant was
slated to open on Wednesday morning – meaning
a solution had to be found, installed and properly
operating in one day!
CASE STORY
Doctor’s offices
With an existing office space, flexible installation options are a welcome advantage. Small offices like this one may not have much mechanical space. The solution: The EZ Boost System was installed above the lay-in ceiling.
Most pumps would be too noisy for this type of installation but not the EZ Boost System. Its variable frequency drive operation is smooth and quiet.
The pressurized diaphragm tank can sit horizontally and the pump is installed inline with the piping system.
APPLICATIONS
Laundry
The EZ Boost System can make it possible to run multiple fixtures without loss in pressure. Compact, clean installation and quiet opera-tion make EZ Boost a perfect choice for laundry applications.
MRI facilities
An MRI facility might need extra pressure to cool the MRI machine. Even with space at a premium, the EZ Boost has been installed in a space as small as a janitor’s closet.
Condominiums
For multiple housing units, EZ Boost can be installed in parallel (each pump must be connected its own controller. Pumps can be installed either horizontally or vertically.
Luxury homes
Comfort and convenience for luxury homes...with an EZ Boost System in place, an upstairs bathroom or shower can have the same water pressure as downstairs. Filling the pool... while taking a bath...while running the dishwasher! is no longer a problem.
BMQE Pump
Pressure Sensor
Diaphragm Tank
2
3
4
1 5 66
EZ Boost System Typical Application
4. Pressure sensor5. Mounting brackets (included with pump)
6. Flex connector
Pos.1. EZ Boost BMQE pump2. EZ Boost controller3. Diaphragm tank (recommended size 2 US gallons/130 psi)
Installation above ceiling and closeup view
LEZSL001_EZBoostBroch_0306.indd 2 3/20/2006 12:02:20 PM
Grundfos — a world-wide supplierGrundfos offers an efficient world-wide service network. Experienced service technicians and all necessary spare parts are available at short notice in all corners of the world.
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
GRUNDFOS Canada Inc.2941 Brighton RoadOakville, Ontario L6H 6C9 CanadaTelephone: 905 829 9533Fax: 905 829 9512
Bombas GRUNDFOS de Mexico S.A. de C.V.Boulevard TLC #15 Parque Stiva Aeropuerto Apodaca, N.L. Mexico 66600 Telephone: 52 81 8144 4000Fax: 52 81 8144 4010
GRUNDFOS Pumps Corporation17100 West 118th TerraceOlathe, Kansas 66061Telephone: 913 227 3400Fax: 913 227 3500
www.grundfos.com
GRUNDFOS EZ BOOST™ SYSTEM
Reliable, economical pressure boosting for smaller buildings
• medical offices
• restaurants
• homes
• condos
• irrigation
• grocery
Pressure boosting made EZ
L-EZ-SL-001 3/06 (US)Subject to alterations
However, R. L. Feezer Construction Inc. solves this
problem with Grundfos EZ Boost. According to Gen-
eral Manager Rusty George, “Traditional tank sizes
are dictated because the pressure boosting pump
has to be mounted inside the tank, requiring a large
tank. With EZ Boost’s external installation, we have
many more options for tank selection, so now we
use a round tank that is easier to install, costs less,
and eliminates expensive rework of door jambs.” The
result was a savings to the homeowner in terms of
the cost of the tank and labor.
CASE STORYLuxury home application
Submitted by
Rusty George, General Manager
R.L. Feezer Construction Inc.
Sykesville, Maryland
Central Maryland illustrates a common problem
when it comes to water pressure for larger homes.
The water level in the area’s 6” rock wells is very deep,
and the yields are inadequate to pump from the well
direct to housing fixtures. Therefore a holding tank
becomes necessary. Often the only place to install a
holding tank is in the basement – particularly in the
North East where sub-zero temperatures are common
during winter.
Installing a 600 - 1000 gallon holding tank in a base-
ment presents another problem….how to get a large
32” wide X 62” long X 62” tall, rectangular holding
tank down a flight of stairs that, halfway, turns left at
a landing and through a 30” doorway. Since the tank
is larger than the door’s opening size, the door’s frame
must be widened to fit the unruly holding tank.
To choose the appropriate EZ-Boost system for your application is simple. 1. Determine how much pressure you need at a given flow.2. Find-out how much pressure you have available (inlet pressure).3. Select a pump from the chart that gives you the difference.
Example: Need 15 gpm with a total pressure of 60 psi. My line pressure is 20 psi, therefore Ineed a boost of 40 psi.The correct selection would be a Model 22 BMQE 05A-80.
Additional (boost) pressure required
5 10 15 20 25 30 35 39Flow required in gallons per minute (GPM)
in PSI908070605040302010
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 05A-80
22 BMQE 05B-120
22 BMQE 10C-190
30 BMQE 10C-130
30 BMQE 05B-90
EZ Boost Quick Sizing GuideChoosing the appropriate EZ Boost pump for your application is simple:
1. Determine how much pressure you need at your maximum flow.
2. Find out how much pressure you have available (minimum inlet pressure).
3. Select a pump from the chart that gives you the difference.
Example: I need maximum 15 gpm with a total pressure of 60 psi.
My minimum inlet pressure available is 20 psi, so I need a boost of 40 psi.
The correct selection would be a Model 15 BMQE 05A-110.
Typical EZ Boost residential installation
With EZ Boost there are more tank options
LEZSL001_EZBoostBroch_0306.indd 1 3/20/2006 12:02:14 PM
EZ Boost System solves low water pressureIf your problem is low water pressure, Grundfos EZ
Boost is your solution. Grundfos EZ Boost provides
constant water pressure – even while multiple taps
are on, and is perfect for large residential & light
commercial pressure boosting applications:
• medical offices • restaurants • homes
• condos • irrigation • grocery
• plus many other boosting applications
Grundfos’ EZ Boost is a complete pressure boosting
system that includes pump, controller, tank, mount-
ing brackets, and pressure sensor. Its high-quality
construction and rugged design ensures low-main-
tenance and trouble free operation. EZ Boost can be
installed just about anywhere; it is simple to install
and simple to operate. Additionally, it is competitive-
ly priced when compared to other pressure boosting
alternatives.
Grundfos EZ Boost features:
> Maintenance-free
• Seal-less and self-cooling
> Dry-run protection
• Protects the pump from damage if
the water supply runs dry
> Standard home outlet voltages (single phase)
• All models available in 230 volt and
some models available in 115 volt
> Soft-start
• Prevents water hammer in pipes and
stress on the pump (also minimizes
flickering lights)
> Overload and underload protection
• Slows or stops the pump to protect the
motor during unstable voltage conditions
> Many installation options:
• Wall-mounted • Framed-in
• In-ground • Equipment build-on
• Portable devices
EZ BOOST ™ SYSTEM
Performance curves
0 5 10 15 20 25 30 35 Q [US GPM]
0
40
80
120
160
200
240
280
[ft]H
0
20
40
60
80
100
120
P[psi]
TK
01 3
100
4801
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 10C-190
22 BMQE 05B-120
22 BMQE 05A-80
30 BMQE 10C-130
30 BMQE 05B-90
BMQE60 Hz
Technical data
6
2
5 4 7
31
8Flow: Max. 40 gpm (9 m3/h)Head: Max 300 ft./130 psi (91 m)Fluid temperature: Max. 95°F (35°C)Ambient temperature: Min. 32°F (0°C)Operating pressure: Max. 145 psiInlet pressure: Min. 8 psi Max. limited by operating pressureOperating setpoint: 40 to 100 psi (in 10 psi increments)Sound pressure level: < 74 dB(A) at a distance of 3 ft. (1 m) from the pump. Note: Sound-sensitive installations may require insulation.
Pos.1. Sleeve2. Discharge connection3. Suction connection4. Submersible motor
5. Submersible pump6. Cable entry7. Centering device8. Air vent screw
Wes recommended the Grundfos EZ Boost System
model 22BMQE10-190 which, fortunately, he had in
stock.
On Wednesday morning, Wes stopped by the res-
taurant and found it packed with customers. When
it was convenient he discussed the situation with
the owner who was delighted with the Grundfos EZ
Boost System.
This EZ Boost System
boosted water pressure
from the city’s main from
20 psi to the 60 psi needed
for this restaurant’s soda
fountains and toilets.
Ice cream restaurant application
Submitted by
Wes Blumenauer, CEO
The Blumenauer Corporation
Ocoee, Florida
Wes received a phone call late on a Monday after-
noon from a desperate plumber looking for a pump
to solve a water pressure problem at a Friendly’s Ice
Cream Restaurant in Clermont, Florida.
The first problem was the city’s water main could
only supply 20 PSI to the restaurant. The plumber
said at least 60 PSI was required to operate the soda
machines and flush the toilets.
The second problem was that the restaurant was
slated to open on Wednesday morning – meaning
a solution had to be found, installed and properly
operating in one day!
CASE STORY
Doctor’s offices
With an existing office space, flexible installation options are a welcome advantage. Small offices like this one may not have much mechanical space. The solution: The EZ Boost System was installed above the lay-in ceiling.
Most pumps would be too noisy for this type of installation but not the EZ Boost System. Its variable frequency drive operation is smooth and quiet.
The pressurized diaphragm tank can sit horizontally and the pump is installed inline with the piping system.
APPLICATIONS
Laundry
The EZ Boost System can make it possible to run multiple fixtures without loss in pressure. Compact, clean installation and quiet opera-tion make EZ Boost a perfect choice for laundry applications.
MRI facilities
An MRI facility might need extra pressure to cool the MRI machine. Even with space at a premium, the EZ Boost has been installed in a space as small as a janitor’s closet.
Condominiums
For multiple housing units, EZ Boost can be installed in parallel (each pump must be connected its own controller. Pumps can be installed either horizontally or vertically.
Luxury homes
Comfort and convenience for luxury homes...with an EZ Boost System in place, an upstairs bathroom or shower can have the same water pressure as downstairs. Filling the pool... while taking a bath...while running the dishwasher! is no longer a problem.
BMQE Pump
Pressure Sensor
Diaphragm Tank
2
3
4
1 5 66
EZ Boost System Typical Application
4. Pressure sensor5. Mounting brackets (included with pump)
6. Flex connector
Pos.1. EZ Boost BMQE pump2. EZ Boost controller3. Diaphragm tank (recommended size 2 US gallons/130 psi)
Installation above ceiling and closeup view
LEZSL001_EZBoostBroch_0306.indd 2 3/20/2006 12:02:20 PM
EZ Boost System solves low water pressureIf your problem is low water pressure, Grundfos EZ
Boost is your solution. Grundfos EZ Boost provides
constant water pressure – even while multiple taps
are on, and is perfect for large residential & light
commercial pressure boosting applications:
• medical offices • restaurants • homes
• condos • irrigation • grocery
• plus many other boosting applications
Grundfos’ EZ Boost is a complete pressure boosting
system that includes pump, controller, tank, mount-
ing brackets, and pressure sensor. Its high-quality
construction and rugged design ensures low-main-
tenance and trouble free operation. EZ Boost can be
installed just about anywhere; it is simple to install
and simple to operate. Additionally, it is competitive-
ly priced when compared to other pressure boosting
alternatives.
Grundfos EZ Boost features:
> Maintenance-free
• Seal-less and self-cooling
> Dry-run protection
• Protects the pump from damage if
the water supply runs dry
> Standard home outlet voltages (single phase)
• All models available in 230 volt and
some models available in 115 volt
> Soft-start
• Prevents water hammer in pipes and
stress on the pump (also minimizes
flickering lights)
> Overload and underload protection
• Slows or stops the pump to protect the
motor during unstable voltage conditions
> Many installation options:
• Wall-mounted • Framed-in
• In-ground • Equipment build-on
• Portable devices
EZ BOOST ™ SYSTEM
Performance curves
0 5 10 15 20 25 30 35 Q [US GPM]
0
40
80
120
160
200
240
280
[ft]H
0
20
40
60
80
100
120
P[psi]
TK
01 3
100
4801
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 10C-190
22 BMQE 05B-120
22 BMQE 05A-80
30 BMQE 10C-130
30 BMQE 05B-90
BMQE60 Hz
Technical data
6
2
5 4 7
31
8Flow: Max. 40 gpm (9 m3/h)Head: Max 300 ft./130 psi (91 m)Fluid temperature: Max. 95°F (35°C)Ambient temperature: Min. 32°F (0°C)Operating pressure: Max. 145 psiInlet pressure: Min. 8 psi Max. limited by operating pressureOperating setpoint: 40 to 100 psi (in 10 psi increments)Sound pressure level: < 74 dB(A) at a distance of 3 ft. (1 m) from the pump. Note: Sound-sensitive installations may require insulation.
Pos.1. Sleeve2. Discharge connection3. Suction connection4. Submersible motor
5. Submersible pump6. Cable entry7. Centering device8. Air vent screw
Wes recommended the Grundfos EZ Boost System
model 22BMQE10-190 which, fortunately, he had in
stock.
On Wednesday morning, Wes stopped by the res-
taurant and found it packed with customers. When
it was convenient he discussed the situation with
the owner who was delighted with the Grundfos EZ
Boost System.
This EZ Boost System
boosted water pressure
from the city’s main from
20 psi to the 60 psi needed
for this restaurant’s soda
fountains and toilets.
Ice cream restaurant application
Submitted by
Wes Blumenauer, CEO
The Blumenauer Corporation
Ocoee, Florida
Wes received a phone call late on a Monday after-
noon from a desperate plumber looking for a pump
to solve a water pressure problem at a Friendly’s Ice
Cream Restaurant in Clermont, Florida.
The first problem was the city’s water main could
only supply 20 PSI to the restaurant. The plumber
said at least 60 PSI was required to operate the soda
machines and flush the toilets.
The second problem was that the restaurant was
slated to open on Wednesday morning – meaning
a solution had to be found, installed and properly
operating in one day!
CASE STORY
Doctor’s offices
With an existing office space, flexible installation options are a welcome advantage. Small offices like this one may not have much mechanical space. The solution: The EZ Boost System was installed above the lay-in ceiling.
Most pumps would be too noisy for this type of installation but not the EZ Boost System. Its variable frequency drive operation is smooth and quiet.
The pressurized diaphragm tank can sit horizontally and the pump is installed inline with the piping system.
APPLICATIONS
Laundry
The EZ Boost System can make it possible to run multiple fixtures without loss in pressure. Compact, clean installation and quiet opera-tion make EZ Boost a perfect choice for laundry applications.
MRI facilities
An MRI facility might need extra pressure to cool the MRI machine. Even with space at a premium, the EZ Boost has been installed in a space as small as a janitor’s closet.
Condominiums
For multiple housing units, EZ Boost can be installed in parallel (each pump must be connected its own controller. Pumps can be installed either horizontally or vertically.
Luxury homes
Comfort and convenience for luxury homes...with an EZ Boost System in place, an upstairs bathroom or shower can have the same water pressure as downstairs. Filling the pool... while taking a bath...while running the dishwasher! is no longer a problem.
BMQE Pump
Pressure Sensor
Diaphragm Tank
2
3
4
1 5 66
EZ Boost System Typical Application
4. Pressure sensor5. Mounting brackets (included with pump)
6. Flex connector
Pos.1. EZ Boost BMQE pump2. EZ Boost controller3. Diaphragm tank (recommended size 2 US gallons/130 psi)
Installation above ceiling and closeup view
LEZSL001_EZBoostBroch_0306.indd 2 3/20/2006 12:02:20 PM
Grundfos — a world-wide supplierGrundfos offers an efficient world-wide service network. Experienced service technicians and all necessary spare parts are available at short notice in all corners of the world.
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
GRUNDFOS Canada Inc.2941 Brighton RoadOakville, Ontario L6H 6C9 CanadaTelephone: 905 829 9533Fax: 905 829 9512
Bombas GRUNDFOS de Mexico S.A. de C.V.Boulevard TLC #15 Parque Stiva Aeropuerto Apodaca, N.L. Mexico 66600 Telephone: 52 81 8144 4000Fax: 52 81 8144 4010
GRUNDFOS Pumps Corporation17100 West 118th TerraceOlathe, Kansas 66061Telephone: 913 227 3400Fax: 913 227 3500
www.grundfos.com
GRUNDFOS EZ BOOST™ SYSTEM
Reliable, economical pressure boosting for smaller buildings
• medical offices
• restaurants
• homes
• condos
• irrigation
• grocery
Pressure boosting made EZ
L-EZ-SL-001 3/06 (US)Subject to alterations
However, R. L. Feezer Construction Inc. solves this
problem with Grundfos EZ Boost. According to Gen-
eral Manager Rusty George, “Traditional tank sizes
are dictated because the pressure boosting pump
has to be mounted inside the tank, requiring a large
tank. With EZ Boost’s external installation, we have
many more options for tank selection, so now we
use a round tank that is easier to install, costs less,
and eliminates expensive rework of door jambs.” The
result was a savings to the homeowner in terms of
the cost of the tank and labor.
CASE STORYLuxury home application
Submitted by
Rusty George, General Manager
R.L. Feezer Construction Inc.
Sykesville, Maryland
Central Maryland illustrates a common problem
when it comes to water pressure for larger homes.
The water level in the area’s 6” rock wells is very deep,
and the yields are inadequate to pump from the well
direct to housing fixtures. Therefore a holding tank
becomes necessary. Often the only place to install a
holding tank is in the basement – particularly in the
North East where sub-zero temperatures are common
during winter.
Installing a 600 - 1000 gallon holding tank in a base-
ment presents another problem….how to get a large
32” wide X 62” long X 62” tall, rectangular holding
tank down a flight of stairs that, halfway, turns left at
a landing and through a 30” doorway. Since the tank
is larger than the door’s opening size, the door’s frame
must be widened to fit the unruly holding tank.
To choose the appropriate EZ-Boost system for your application is simple. 1. Determine how much pressure you need at a given flow.2. Find-out how much pressure you have available (inlet pressure).3. Select a pump from the chart that gives you the difference.
Example: Need 15 gpm with a total pressure of 60 psi. My line pressure is 20 psi, therefore Ineed a boost of 40 psi.The correct selection would be a Model 22 BMQE 05A-80.
Additional (boost) pressure required
5 10 15 20 25 30 35 39Flow required in gallons per minute (GPM)
in PSI908070605040302010
15 BMQE 07B-180
15 BMQE 05A-110
22 BMQE 05A-80
22 BMQE 05B-120
22 BMQE 10C-190
30 BMQE 10C-130
30 BMQE 05B-90
EZ Boost Quick Sizing GuideChoosing the appropriate EZ Boost pump for your application is simple:
1. Determine how much pressure you need at your maximum flow.
2. Find out how much pressure you have available (minimum inlet pressure).
3. Select a pump from the chart that gives you the difference.
Example: I need maximum 15 gpm with a total pressure of 60 psi.
My minimum inlet pressure available is 20 psi, so I need a boost of 40 psi.
The correct selection would be a Model 15 BMQE 05A-110.
Typical EZ Boost residential installation
With EZ Boost there are more tank options
LEZSL001_EZBoostBroch_0306.indd 1 3/20/2006 12:02:14 PM