luxurite cabinet door tv user manual

8/14/2019 Luxurite Cabinet Door TV User Manual

1/34

We continuously improve our products specifications and details. The pictures used in this menu

subject to changes and products improvement. Please contact your supplier to confirm

specifications before purchase.

CABINET DOOR TVUSER MANUAL


2/34

www.luxurite.com

Sky eye


3/34

Contents

WARNINGS AND CAUTIONS

Safety instructions

Introduction ComponentsIntroduction

Remote Control

General OperationMain Operation

Connection

ATV

DTV

On Screen DisplayMENU (OSD)

Trouble shooting

01

05

09

09

20

24

25

29

43

49

55

Installation

Remote Control Key Functions

ExcursusTechnical specifications

Declaration and Notesfor PC part of the Cabinet Door TV

15

53


4/34

2

Before using t his product please read the instruction manual carefully

whic h wil l ensure correct installation and ease of use. Please keep t his

manual for future reference. The information in this manual is subject to

the change without prenotice.

Thank you for choosing LUXURITE Cabinet Door TV.

WARNING:TO REDUCETHE RISK OF ELECTRIC SHOCK DO NOT REMOVEENCLOSURE.

NO USER SERVICEABLEPARTSINSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended toalert the user to the presence

of uninsulated dangerousvoltage within the productsenclosure that may be of sufficient magnitude to constitute

a risk o f electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing )instructions in theliterature accompanying the appliance.

CAUTION

RISK OF ELECTRICSHOCK

DO NOT OPEN

REGULATORY INFORMATIONThis equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction s, may cause harmful interference to radio communication.However, there

is no guarantee that int erference will not occur in a particular installat ion. If this equipment does cause

harmful interf erence to radio or television reception, which can be determined by turning the

equipment off and on. The user encouraged t o try to correct the interference by oneor more of the

following measures:

Relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Contact the dealer or experienced radio/TV technician for help.

Any changes or modif ication s not expressly approved by th e part y responsible fo r

compliance could void the user s authorit y to operate the equipment.

CAUTION:

Do not attempt t o modify this product in any way without authorization from supplier.

Unauthorized modification could void the user s authority t o operate this product.

WARNINGS AND CAUTIONS

48

8G

This is an All-in-One machine of TV and PC,with independent switch,

plesae select t he necessary switch according to your requirement.Switch off

the part which does not use will be helpful to the maintenance of the machine.

It will increase the machine`s heat if turning on the TV power and PC power

simultaneously.For the better maintenance of the machine,please do not turn on

TV power and PC power more than 48 hours at one time.

The PC equipped wit h standard 8G solid state Disk space should be deleted the

unnecessary files to ensure the normal operation of the PC system.

The build in wireless network adapter can be linked to the network

without cable.


5/34

43

High voltage is used in the operation of this

TV door receiver. Do not remove the cabinet

back from the set. Refer servicing to qualified

service personnel.

LUXURITE

Cabinet Door TV

WARNING

To prevent fire or electrical shock hazard,

do not expose the TV door receiver to rain or

moisture.

WARNING

Do not drop or push objects into the TV door

cabinet slots or openings. Never spill any

kind of liquid on the TV door receiver.

WARNING

Excessive sound pressure from earphones

and headphones can cause hearing loss.

WARNING

Do not block t he ventilation holes in the back

cover. Adequate ventilation is essential to prevent

failure of electrical components.

Do not t rap the power supply cord under the

TV door receiver.

CAUTION

CAUTION

LUXURITE

Cabinet Door TV

LUXURITECabinetDoorTV

Class 1 construction. Must be connected to a

mains socket with protective earthing.

Never stand on, lean on, or suddenly push

the TV door or its stand. You should pay special

attention t o children. Failure to follow these

instructions may result in serious injury.

WARNING

LUXURITE

Cabinet Door TV

CAUTION

Do not place your TV door on an unstable cabinet.

Failure to follow these instructions may result in

serious injury to individual or damageto TV door.

When the TV door receiver is not used for an

extended period of time, it is advisable to

disconnect the AC power cord from the AC outlet.

Avoid exposing the TV door receiver to direct

sunlight and other sources of heat. Do not install

the TV door receiver directly on other products

which give off heat, e.g.video cassette players and

audio amplifiers. Do not place naked flame

sources, such as lighted candles on the television.

CAUTION

CAUTION

CAUTION

LUXURITE

Cabinet Door TV



6/34

Only use with power supply provided.

The luxurite system components should be

mounted in a dry location away from heat

sources,i.e. away f rom heat/flame/steam/moisture.

The PSU should be located where the PSU

cord is protected from movement or stress.

CAUTION

WARNING

WARNING

LUXURITE

Cabinet Door TV


IM PORTANT SAFETY INSTRUCTIONS

WARNING :

To avoid the risk of f ire or electric shock, do not expose this apparatus to rain or moisture.

Apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such

as vases, shall be placed on the apparatus.

Safety Instructions

1.Read these safety instructions.

2.Keep these safety instructions.

3.Heed all warnings.

4.Where the mains plug or an appliance coupler is used as

the disconnect device,the disconnect device shall remain

readily operable.

5.Follow all safety instructions.

6.Do not use this apparatus near water.

7.Clean only wit h dry cloth.

8.Do not block any ventilation openings. Install in

accordance wit h t he manufacturer's

instructions.

9.Do not install near any heat sources such as radiators,

stoves or other apparatus

(including amplifiers) that produce heat.

10.Protect the power cord from being walked on or

squeezed particularly at power outlets and the point

where they exit from the apparatus.

11.Only use attachments/accessories specified by the

manufacturer.

12.Unplug this apparatus during lightning storms or when

unused for long periods of t ime.

13.Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as the power-supply cord

or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

14.Apparatus must not be exposed to dripping or

splashing and no objects filled with liquids, such as vases,

should be placed on the apparatus.

65


7/34

7

Introduction

If the TV is under cold condition, there may be a small flicker when you turn it on.

Avoid touching the LCD screen or holding your finger(s) against it.

Do not overload wall outlets. Overloaded wall out lets could damage the TV and could also result in

electric shock or fire. Periodically examine the cord of your appliance; if it s appearance indicates

damage or deterioration, unplug it. Stop using it until you have it replaced with a cord authorized

by your dealer. Protect the power cord from physical or mechanical abuse, such as being twisted,

kinked or pinched.

CAUTION connecting t he Power Cord

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury

Disposal of this product must be carried out in accordance with the regulations of your local

authority.

Note


8/34

This is a simplified representation of the product.

There might be some differences from your actual unit.

Ensure that the follow ing components are att ached with your TV. If any accessory is missing, please

contact the dealer where you purchased the product.

109

Components

Power Lead + Ad aptor Remote control

Media Box

User manual

Introduction

ITEM NAM E FUNCTION DESCRIPTION

Cont rol Panel

LCD display screen

Rear Panel

LCD display screen

Specification of this Part Views in following page

Specification of this Part Views in following page

TV door Keyboard and mouse

TV door

Media Box

Remot e sensor

Cont rol Panel

Rear Panel

LCD display

screen

Media Box

TV door

Media Box has TV and PC funct ion

Cabinet door used for kitchen furniture

Remote sensor Infrared sensor for the remote control.

Sky eye


9/34

1211

Control Panel Rear Panel

ITEM NAME / SYMBOL FUNCTION DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11

ITEM

Turn on/off the LCD TV

Press to select the input source.

Press to decrease the sound level.

Channel+

Press to bring up the main menu to t he screen.

Channel-

Press to increase the sound level.

Red/Green light indicates LCD TV is at standby/w orking mode;POWERINDICATOR


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

ITEM

DC 12V

HDMI

VGA

S-VIDEO

AUDIO IN - R

R F

DC power Input, supplied with DC 12V

High-Definition Multimedia interface Input

connected with Y/C video signal from external signalequipment

CVBSconnected with CVBSvideo signal from external signalequipment

AUDIO IN - Lconnected with stereo audio signal input interface L from

signal equipment

connected with stereo audio signal input interface R fromsignal equipment

AUDIO IN -PC connected with audio card input of PC

connected with external loudhailer and earplug output

Analog / Digital Antenna input.

1 2 3 4 5 6 7 8 9 10 11

VOL

VOL

CH

CH

INPUT

PC Turn on/off the PC

Blue light indicates PC isON mode.PC INDICATOR

Data media interface

1 2 3 4

5 6 7 8 119 10 12 13 1514

Y

Pr/Cr

Pb/Cb

COMMON INTERFACE

Scart

The red-difference chroma components

The blue-difference chroma components

Y' is the luma component

Digital Video Broadcasting Common Interface

Connected with Scart cable

Media box PC's Analog RGB signal output


10/34

13

Flank Panel

1 2 3


1

2

3

ITEM

LAN jack

USB port

SKY EYEConnect SKY EYEFor LUXURITESKY EYEonly Installation


11/34

1615

All electrical work should be undertaken by a suitably qualified person.

1. Fix hinge with screw provided.

TV DOORScrew

Screw

Door hinges

2. Fit door to cabinet as per standard

TV DOORCabinet

3. Align door to desired position

4. Fit media hub to cabinet (screwing)

Front view Side view


12/34

5.Connect cable from door to media box.

1817

6. Connect power supply to media box.

7.Connect TV aerial or set box to aerial or scart connector on media hub.

TV

DVD


13/34


14/34

22

1 2 3

4 5 6

7 8 9

0-/--ASPECT NICAM

DISPLAY

LCDMENU

DVDSETUP

I NPU T PM OD E SM OD E SLEEP

FAV FAV- FAV+ EPG

TEXT HOLD LANG SUBTITLE

INDEX SiZE REVEAL SUBPAGE

EXIT

STANDBYEJECT

AUTOMUTE

ENTER

Sub coded page access;

SUBPAGE

Reveal or hidden the hidden words;

REVEAL/ANGLE

Change display size in teletext mode;

SIZE

INDEXRequest the index page;

To switch the dialogue at the bottom of the screen.

SUBTITLE

To show the list of audio languages available for the

Current channel. Just in DVB mode;

LANG

Hold On or Off for current page display;

HOLD

Switch On or Off the teletext mode;TEXT

21

1 2 3

4 5 6

7 8 9

0-/--ASPECT NICAM

DISPLAY

LCDMENU

DVDSETUP

I NPU T PM OD E SM OD E SLEEP

FAV FAV- FAV+ EPG

TEXT HOLD LANG SUBTITLE

INDEX SiZE REVEAL SUBPAGE

EXIT

STANDBYEJECT

AUTOMUTE

ENTER

/ / / /ENTER

Allows you to navigate the on-screen menus and

adjust the system settings to your preference.

Press to display FAV menu in DVB mode;

FAV

DVB source decrease fav channel;

FAV-

DVB source increase fav channel;

FAV+

Press to show t he Electron ic Program Guide menu.

EPG

Press to cycle through the input source.

Press repeatedly to cycle through the available videopicture modes

Press to cycle through the different sound settings.

Let you select a mount of time before your TV turn

itself off automatically.

INPUT

PMODE

SMODE

SLEEP

Brings up the LCD main menu to the screen in an-

alogue TV mode.

To exit menu or submenu.

LCD MENU

EXIT


15/34

24

TURN ON LCD TV1. Connect the AC power adapter cable to TV, At th is time the TV will enterstandby into mode

and the indicator will switch to red as standby mode

2. Press STANDBYbut ton on the TV set or but ton on the remote cont rol to turn on LCD

TV. Indicator will switch to green as working mode.

TURN OFF LCD TV

1. Press STANDBY button on the TV set or but ton on the remote control to enter standby

mode. At this time indicator will switch to red.

2. Unplua the LCD TV to t urn off completely.

Act ivate th e INPUT SOURCE1. press INPUT button on the control panel or on the remote control to display input source.

2. Press / butt on to select input source.

3. Press the enter butt on to choose the menu you want.

Main Operation

TVSCART

cvbsS-VIDEO

PC

HDMI

DTV

Please keep PC off w hen you do not use computer function to save power and PC life.

In the PC mode, the LAN jack and USB port can be used as in normal computers. And the

VGA socket can be used for media box PC's RGB signal output.Please consult computer

professionals if you have any enquiries.

PC:

General Operation Turn on PC button on the media box and press Input key on the remote control,Choose PC mode. In this mode, the TV DOOR can be used as a normal computer with enclosed

wireless keyboard and mouse. Please consult your supplier for specific features such as operating

system, computer configuration.


16/34

Make sure that both of HDMI device and LCD TV are power off

Connect HDMI device and LCD TV with the HDMI cable.

Turn on the LCD TV , then turn on the HDMI device

Select HDMI mode

Control the volume by VOL- / VOL+

LCD TV can be turned off by power butt on on remote control

3. Connect to the HDMI

AUDIO INL

AUDIO INR

CVBSCVBScable AUDIO cableL

AUDIO cableR

26

1. Connect t he TV

Make sure that LCD TV is power off

Insert the TV cable into antenna socket

Turn on the TVSelect TV mode


Using CH+/CH- to choose the channel


2. Connect to CVBS/S-VIDEO device

Make sure that both of CVBS/S-Video device and LCD TV are power off

Connect CVBSdevice and LCD TV w ith CVBScable or S-VIDEO cable

Connect audio cable into the audio input jack on LCD TV

Turn on the LCD TV , then turn on the CVBS/S-VIDEO device

Select CVBSor S-VEDIO mode



CONNECTION

TV cable AntennaSocket

S-VIDEO

cable

25

S-VIDEO

HDMIHDMI cable


17/34

On Screen Display MENU(OSD)

In the PC mode, the LAN jack and USB port can be used as in normal computers. Please

consult computer professionals if you have any enquiries.

4. Connect to LAN and USB

27


18/34

ATV

Delete Analog Program

Press / butt on and then use / to select whether to delete all the analog programs.

Language

Press / butt on and then use / to select the OSD language.

The instruct ion is for reference only,the actual OSD

(On Screen Display)menu may be different from your TV`s

First Time Installation


Country

Language

Delete Analog Program

Analog Program Search

Delete Digital Program

Digital Program Search

UK

English

OK Cancel

Select Adjust

If this is the first t ime you open the TV and there is no programs in the TV memory, t he

First Time Installation menu will appear in the picture.

Country

Press / butt on and then use / to select the country.

3029

25

Auto

No Signal

Auto

TV Label


YES

First time installation is not finished!

Are you sure to exit?

Do It next time NO

TV Information

1

2

3

5

6

4

After setting the items, select OK to finish the first time installation, or select Cancel to exit

this menu.

Delete Digital Program

Press / but ton and then use / to select whether to delete all the digital programs.

Digit al Program Search

Press / but ton and then use / to select whether to start searching digit al programs.

Analog Program Search

Press / but ton and then use / to select whether to start searching analog programs.

If you cancel the first time installation, it will remind you to set the first time

installation next time.

Program Inform ation

Press DISPLAY or NICAM button to display the program information.


19/34

3231

If the icon of NICAM mode is red, it means the current program supplies multi NICAM

signals, and you can select it by pressing NICAM button.

Mono Stereo Dual Dual

The NICAM modes and relative icons:

VIDEO menu o pti onsPress MENU button on the front panel or LCD-MENU on the remot e contro l to display the main

menu.

PICTURE

PictureMode

Contrast

Sharpness

Tint

Colour

Brightness

Standard

50

50

50

0

Normal

Select Adjust

Press / but ton to select PICTURE in the main menu.

Press / button to select the option that you want to adjust in the PICTURE menu.

Press / but ton to adjust.

1. The number of current program.

2. The colour system of current program, could be selected in Manual Tuning menu (an option

of SETUPmenu).

3. The name of current program.

4. The label of current program, you can label it in Manual Tuning menu(an option of SETUP

menu).

5. The sound system of current program, could be selected in Manual Tuning menu (an optionof SETUPmenu).

6. The NICAM mode of current program.

PICTURE

Colour

Sharpness

Tint

Colourtemperature

DNR

50

0

Normal

Off

Normal

Select Adjust

Contrast

Press / butt on and then use / to adjust the contrast of the picture.

Contrast 28

After adjusting the value you want, press LCD-MENU button t o return to the preview MENU.

Brightness

Press / but ton and then use / to adjust the bright ness of the picture.

Picture M ode

Select Picture Mode in PICTURE menu. (Available picture mode: Standard, Personal,Movie,

Sport, Mild, Game.)

If you change the value of Contrast, Brightness, Colour, Tint, Sharpness or Colour temperature

on the picture menu, the picture mode will be changed to "Personal" automatically. You may

select the picture mode directly by pressing PMODEbutton.

When you are satisfied with your adjustment , press the LCD-MENU button to return to the

previous menu or press the EXIT button to exit the main menu.

TIPS

You can pressPMODE button on the remote control, to select the Picture Mode directly.


20/34

3433

SOUND

Volume

SoundMode

Balance

Treble

Bass

Personal

28

0

0

0

Select Adjust

Colour t emperature

Select an optimum colour temperature mode to suit your eyes for viewing among Warm

and Cold.

NOTE: This option is available only in PC mode.

DNR (Digit al Noise Reductio n)

If the broadcasting signal received is weak, you can select t he DNR opt ion t o reduce the video

noise level between Off, Low,Mid and High.

Sharpness

Press / To select the sharpness mode of your TV. (Available Sharpness Mode: Normal, Sharp,

Sharpest, Softest, Soft.)

Colour

Press / butt on and then use / to adjust the colour saturation.

NOTE: This option is invalid in PC mode, and it will be shown in gray.

Tint

Press / butt on and then use / to adjust the tone of colour when your system is in NTSC.

AUDIO menu optio ns

Press MENU button on the front panel or LCD-MENU on the remote control to display

the main menu.

Aft er adjust the value you want, press LCD-MENU button to return to the preview MENU.

Sound M ode

Select Sound M ode in SOUND menu. (Available sound mode: Personal, Voice, Music, Theatre.)

If you change the value of Bass and Treble on the Sound menu, the sound mode will be changed

to " Personal" aut omatically. You may select the sound mode directly by pressing SMODEbutton.

Bass

Press / but ton and then use / to increase or decrease the level of the lower-pitched sounds.

Balance

Press / but ton and then use / to adjust the audio out put between left and right speakers.

Treble

Press / but ton and then use / to increase or decrease the level of the higher-pitched sounds.

Volume 28

Volume

Press / but ton and then use / to adjust the sound level.

Press the / but ton to select SOUND in the main menu.

Press the / button to select the option that you want to adjust in the SOUND menu.

Press the / but ton to adjust.

When you are satisfied with your adjustment, press the LCD-MENU button to return

to the previous menu or press the EXIT button to exit the main menu.

Setup menu opt ions

Press MENU button on the front panel or LCD-M ENU on the remote control to display the main

menu.

You can pressSMODEbutton on the remote control to select the Sound Mode directly.

TIPS


21/34

3635

SETUP

Country

Autotuning

Manualtuning

Program Edit

UK

Select Adjust

SETUP menu of TV inpu t:

Press the / butt on to select SETUPin the main menu.

Press the / bu tton to select your option what you want to adjust in the SETUPmenu.


When you are satisfied with your adjustment, press the LCD-MENU button to return to the


Country

This option allows you to select the country.

Auto tuning

This option allows you to tune the channels that can be received automatically.

SETUP menus are diff erent for dif ferent input sources, if the input source is selected

HDMI / YPbPr / VGA and t here are no relative input signal, SETUPmenu wil l be

unavailable.

NOTE

NOTE

Before you perform Auto Tuning, you must choose the country where you are by selecting

COUNTRY option.

Manualtuning

Program

SoundSystem

ColourSystem

ManualSearch

Program Lable

AFT

23

DK

Auto

Off

471.43 MHz

Select Adjust

Auto Tuning

Searching

6

ExitMENU

ATV 215.00MHz

You can pressLCD-MENU button to stop auto tuning and close the OSD menu.

Manual Tuning

This option allows you to perform Manual Tuning.

Before you perform Manual Tuning, you must choose the country where you are

by selecting Country option.

Press / to select Manual tun ing in SETUPmenu.

Press / to perform your selection, the menu of Manual tuning wil l display on the

screen.

Press ENTER key to start.

Auto Tuning

Press ENTER key to start.

Enter ReturnENTER MENU

1.

2.

NOTE


22/34

3837

Program Label

This option allows you to label a channel. you can also relabel the programs which have

beenlabeled.

Select a channel you want to be labeled.

Press / select Program Label in SETUPmenu.

Press / to perform your selection. The menu of program label wil l display as below:

Program

The current program number. Press / to select the upper or lower program.

Sound System

Press / to select a corresponding sound system, such as DK, L/L , BG.

Colour System

Press / to select a corresponding colour system, such as Auto, PAL, SECAM.

AFT (Aut o Fine Tune)

Due to weak signals or a wrong antenna configuratio n, some of the channels may not

be tuned to the best reception condition. AFT function allows you to fine tune channel

selected(the frequency of channel is around the value in Manual Search option.

Press the numeric buttons to input the numbers directly or press / to select theletters.

Press / to move the cursor.

Press ENTER, LCD-MENU or EXIT button to confirm and return to previous menu.

Program Label

This option has tw o functions:

Set the frequency of channel for AFT option.

Press but ton for 3+ seconds and it will start auto tuning from this frequency.

Manual Search

Manual Search - - - . - - MHz

1.

2.

3.

4.

5.

6.

1.

2.

PC Position

Auto Sync

Phase

Clock

H Position

V Position

Position Reset

Begin

51

Select Adjust

50

50

50

Press / to select Program Edit in SETUPmenu.

Press / to enter into the sub menu, a channel list will display.

Press / to select the channel in the list which you would like to sort.

Press to perform your selection.

Press / to select the location you would like to place the channel.

Press to perform you selection.

Press LCD-MENU to return to the previous menu or press EXIT to exit.

Program Edit

This function allows you to sort

the TV programs according to

your preferences, as fol lowing:

Channel Listhannel ListFlags ATV

Favorite MoveSkip Lock

1.

2.

3.

4.

5.

6.

7.

8.

x

x

x

x

x

x

x

SETUPmenu of VGA input

(for setting the PC picture

position):

1.

2.

3.

4.

5.

6.

7.


23/34

4039

SETUP menu of HDMI input (for setting the HDMI picture position):

HDMI Position

H Position

V Position

Position Reset

Select Adjust

50

50

SETUP menu of YPbPr input (for setting the YPbPr picture position):

YPbPr Position

H Position

V Position

Position Reset

Select Adjust

50

50

Timer menu options

Press MENU button on the front panel or LCD-MENU on the remote control to display

the main menu.

Press the / butt on to select TIMER in the main menu.

Press the / bu tton to select your option what you want to adjust in the TIMERmenu.

1.

2.

Press the / butt on to adjust.



TIMER

SleepTimer

OSDTimer

0 Min.

30Sec

Select Adjust

Sleep Timer

Select the sleep t ime t o put the TV in standby mode automat ically. Timer can be selected

as 0min, 15min, 30min,45min,60min,75min,90min,105min,120min. Also you can select the sleep

time by pressing SLEEPbutt on repeatedly.

OSD Timer

You can select the time when the OSD display on the screen such as: 5Sec,10Sec,15Sec,20Sec,

25Sec,30Sec.

Function menu options

PressMENU button on the front panel or LCD-MENU on the remote control to display the main

menu.

Press the / butt on to select FUNCTION in the main menu.

Press the / butt on to select your option what you want t o adjust in the FUNCTION menu.

Press the / butt on to adjust.



3.

4.

1.

2.

3.

4.


24/34

4241

FUNCTION

Bluescreen On

Video Size Auto


Reset

Language English

Select Adjust

Child Lock

Video Size

This option allow s you to select the screen display mode which best corresponds to your viewing

requirements.

Note: The available aspect mode may be diff erent in di ff erent input signal.

Blue screen

This option allows you to select the blue background on or o ff . If on, the screen

background will turn blue at very weak or no signal condition.

Child Lock

Press ENTER or butt on to set the child lock.

Language

Press / to select the OSD language.

You need to enter the PIN code if the Child lock is set on , and the default PIN code is empty,

you can press ENTER button directly to enter.

PIN Code:

Delete Input0~9 EnterENTER

The supervisor's (administrator' s) password is 4711.

TIPS

FUNCTION

Change PIN Code

Key Lock On

Child Lock On

Select Adjust

Child Lock

Press ENTER or but ton to

set the child lock.

Key Lock

Press ENTER or but ton to

set the key lock.

Change PIN Code

Press but ton to enter

Change PIN Code menu.

Change PIN Code

Enter Again

New PIN Code

Old PIN Code

Select Adjust Input0~9 ConfirmENTER

Old PIN Code

Press 0~9 buttons to enter the correct old PIN code, you can not change the PIN code if you

entered a wrong PIN code.

New PIN Code

Press 0~9 buttons to enter the new PIN code you want.

Change PIN Code

Press 0~9 buttons to enter the PIN code you entered in the New PIN Code menu again to confirm

the new PIN code.


25/34

4443


Press but ton to open the first time installation menu, and the operation of this menu

is in page 3.

Reset

Press ENTER or but ton t o reset the TV to the factory default .

DTV

Channel List opt ions

Channel Listhannel List

Select EnterENTER

DTV

Press ENTER button to open the Channel List, then Press / to select the channel you want to

watch.

Program List

Favorite List opt ions

Press FAV button to open the Favorite List, then Press / to select the channel you want to

watch.

Favorite Listavorite List

Select EnterENTER

Channel Search opt ionsPress the / but ton to select SETUPin the main menu.

Press the / but ton to select your option what you want to adjust in the SETUPmenu.


When you are satisfied with your adjustment, press the LCD-MENU button to return to the


NOTE

Only t he channels that you select to FAV in Program Edit Menu could be displayed

in Favorite List.

1.

2.

3.

4.


26/34

4645

SETUP

Country

Autotuning

Manualtuning

Program Edit

UK

Select Enter

Manualtuning

Channel

Start Search

Service Found

Frequency

Signal Quality

Signal Strength

21

Begin

0%

474.00 MHz

0%

1

Select Adjust Input0~9

Press / butt on to select Manual Search, Press ENTER or but ton to set the Manual

Tuning.

Channel

The current channel number. Press / to select the upper or lower channel. Press 0~9 to

select the channel directly.

Star t Search

To select whether to start searching in begin/searching/finished.

Service Foun d

The services available.

Channel Listhannel ListFlags DTV

Favorite Delete Lock

Signal Qualit y

The signal qualit y of current

channel.

Signal Str engt h

The signal strength of current

channel.

Frequency

The frequency of current channel.

Progr am Edit

This function allows you to edit

the DTV programs according to

your preferences, as fol lowing:

Press Favorite on your remote control to label your f avorite programs.

Press delete to delete programs already added on Channel List.

Press lock to lock up programs according to your preferences.

Common interf ace

If you have inserted a CI card into TV, you can see an OSD menu as followed. Press ENTER to get

detailed CI information.

Common Interface

------- Access


27/34

47

EPG Menu

Use EPG button on the remote control to display the EPG menu directly as below:

Channels

GD TV Best Scapes

Electronic Programme Guide Sun 13/1 22:10

Current Event Next Event

GD TV Best Scapes 22:00-00.00

Navigate Schedule Watch MoreOK INFO

2. GD-3

3. GD-5

4. GD Life

5. GD Finance

Fit & Fearless

The Jewellery Chan...

Programmes start at...

The Ten Minute Free...

GD TV Best Scapes

The Jewellery Chan...

Programmes start at...

The Ten Minute Free...

Trouble shoot ing


28/34

Before contacting the service technician, perform the following simple checks. If any problem

still exists, unplug the LCD TV and call for customer service.

No sound and picture

Normal picture but

no sound

The remote control

does not work

Power is suddenly

turned off

Picture appears slowly

after switching on

No or poor color or

poor picture

Horizontal/vertical bars or

picture shaking

Poor reception onsome channels

Lines or streaks in pictures

PROBLEM

The picture is not sharp.

The picture moves.

- Check that the main plug has been connected to a wall let.- Check that you have pressed the STANDBY button on the front of TV set.

- Check the picture contrast and brightness settings.

- Check the volume.

- Sound muted? Press the MUTEbut ton.

- Try another channel ,the problem may be with the broadcast.

- Are the audio cables installed properly.

- Check to see if there is any object between the product and remote control Causing obstruction.

- Are batteries installed with correct polarity(+ to +,- to -).

- Correct remote operating mode set: TV, VCRetc.

- Install new batteries

- Is the sleep timer set.

- Check the power control settings. Power interrupted.

- No broadcast on station tuned with auto activated.

- This is normal, the image is muted during the product startup process. Please

contact your service center, if the picture has not appeared after five minutes.

- Adjust the color in menu option.

- Keep a sufficient distance between the product and the VCR.

- Try another channel, the problem may be with the broadcast.

- Are the VIDEO cables installed properly?

- Activate any function to restore the brightness of the picture.

- Check for local interference such as an electrical appliance or power tool.

- Station or cable product experiences problems. Tune to another station.- Station signal is weak, reorient antenna to receive weaker station.

- Check for sources of possible interference.

- Check the antenna (Change the direction of the antenna).

The reception may be weak. The state of the

broadcast may also be bad. Make sure the

antenna is facing the right direction. Make sure

the outside antenna is not disconnected.

POSSIBLE SOLUTION

5049

THE CAUSES OF INTERFERE NCE

Incorporated in your TVreceiver aret he most up-to-datedevicesto eliminate interference.

Localradiation, however, cancreatedisturbanceswhich visiblyaff ectyour picture.

Properinstallation, a good aerialis your best safe-guard against thesedisturbances.

RFINTERFERENCE

Movingripplesacrossthe screen arecausedby nearbyt ransmitting or receiving short-waveradioequipment.

DIATHERMY

Herringbone pattern andpartialpicturelosscan result from the operation of diathermy

equipment From a nearbydoctor'ssurgeryor hospital.

Weak TV signalsfrom longdistant stationsresult in an unsteadypictureandgive the effect of

falling snow. An antennaadjustment or antennaamplifiermaybe needed.

SNOW

Multiple images caused by TV signals reflected back from surrounding buildings, hills, aircraft,

etc. is minimised by correct aerialpositioning.

CAR IGNITION

Nearby cars and electrical motors can cause small streaksacross the pictureor maket he

pictureroll.

GHOST


29/34

51

Maintenance

Early mal-functions can be prevented. Careful and regular cleaning can extend the time of

you will have your new TV.

Be sure to turn t he power off and unplug the power cord before you begin any cleaning.

Cleaning the screen

1.Here's a great way to keep the dust off your screen for a while.Wet a soft cloth in a mixture

of lukewarm w ater and a little f abric softener or dish washing detergent.

Wring the cloth until it 's almost dry, and then used it to w ipe the screen.

2.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to

use a wet cloth.

Ext ended Ab sence

If you expect to leave your TV dormant for a long t ime(such as vacation), it' s a

good idea to unplug the power cord t o protect against possible damage from

lightning or power surges.

Excursus


30/34

5453

Technical specifications

LCD SIZE

Brightness

Viewing angle

Resolution

System

Teletext

Input

Amplify

OSD Languages

Power suppy

consumption

10.2 , 15.4 , 17 ,19 , 22 ,

300cd/ ,400 cd/ , 400 cd/ ,450 cd/ , 450 cd/

120(H) / 105(V), 140(H) / 120(V), 140(H) / 120(V),

160(H) / 160(V), 178(H) / 178(V)

10.2 : 800x480

15.4 : 1280x800

17 : 1440x900

19 : 1440x900

22 : 1680 x1050

Video system PAL, SECAM, DVB-T

Audio system BG, DK, I, L/L

300 pages

Nicam/a2 YES

DTV(DVB-T)

ATV

AV,S-video

PC

HDMI

ModulationVideo System

Audio System

Basic Functions

COFDM 2K/8K QPSK,16QAM,64QAMMPEG- MP@ML

MPEG-1/2 layer 1,2,3

EPG,Subtitle,Teletext,(EURO),MHEG-5(UK)

75 ANT.

AV Cable input, S-video input

DB15 VGA Input

480i, 480p, 576i, 576p, 720p,1080i, 1080p

2Wx2

English, French, German, Italian, Spanish, Portuguese.

DC12V

42W, standby


31/34

5655

Declaration and Notesfor PC part of the Cabinet Door TV

Configurations and functions

The PC part of the Cabinet Door TV is intentionally designed for web

pages explore or internet multimedia entertainment. Its settings

(main components: CPU, 1G memory, 8G solid state hard driver) is

not suitable for large scale software, games, long time continuous

turning on. To make sure it works well and save its life, not keep

turning it on for more than 48 hours.

Small hard driver is to make the product works well even in a small

space. It is not suitable for save important files and data. Luxurite is

not responsible for any loss by loss of files or data in this PC part.

Solid state hard driver

System Maintenance

Please run system clearance for system partition partit ion C :

regularly to make sure the PC has enough space to run the system.

Please use one key recovery to recover the PC s system to

original status when the system gets serious problems, crash and

other un-recoverable problems.

Recover procedures

Make sure partition C: has no important files and make copies for all

important data and f iles.

Restart t he cabinet TV door s PC part

Press F9 when the system restarts.

The system will run the recovery procedures automatically and do not

need any other operations.

When the recovery finish, the computer s system reboot to the original

factory status automatically.

When you not use PC function, please make sure the PC is on off

status to save power and computer s life.


32/34

System Safet y

To keep you use the PC part safely, please install anti-virus software

to make the system safe. Luxurite is not responsible for any damage

or loss caused by computer virus.

57

Appliance software

When you need install appliance software, please use the legal copy

and respect the copy right.

`one key recovery` function will overwrite the system partition

C: to original system status, please use this function cautiously.

Warning:

Sky eyeThiscontentsfinal explanation right is belong to LuxuriteUK ltd.

WARRANTY


33/34

WARRANTY

CARD

REPAIR INFORMATION

DATE CONDITION REPAIRMAN

COMMODITY: PRODUCT MODEL:

INSPECTOR:

CONTACT TEL:

CUSTOMER NAME:

SERIES NO: PURCHASING DATE:

INVOICE NO:

PRODUCTION DATE:

SELLER:

THROUGH THETEST OFQUALITY CONTROL DEPARTMENT IN OUR COM PANY, THEPRODUCTHAS BEEN PROVED THAT THE FUNCTION PARA-M ETER HAS REACHED THE TECHNIQUE

CRITERIA. THEY AREPERMITTED TO LEAVEFACTORY.


34/34

luxurite cabinet door tv user manual

Documents