lupus-electronics geodome le 337hd / 338hd
TRANSCRIPT
LUPUS-Electronics GEODOME – LE 337HD / 338HD
User's Manual
Version 1.0.1
2
Table of Contents
Introduction ................................................................................................................. 3
Disclaimer ................................................................................................................... 3
Important safety advice............................................................................................... 3
Notes for usage and installation ................................................................................. 4
In case you encounter an error ................................................................................... 5
Designated use ........................................................................................................... 5
1. General Introduction ............................................................................................. 5
1.1. Overview ........................................................................................................... 5
1.2. Features............................................................................................................ 5
2. Framework and Dimensions ................................................................................ 6
2.1. GEODOME – LE 337HD / 338HD .................................................................... 6
3. Installation ............................................................................................................ 8
3.1. GEODOME – LE 338HD................................................................................... 8
3.2. GEODOME – LE 337HD................................................................................. 11
4. OSD-menu ......................................................................................................... 13
4.1. OSD-menu overview ....................................................................................... 14
3
Introduction
Thank you for purchasing a LUPUS GEODOME® HD camera. Before you begin to
use your camera, please carefully read the following security and installation
instructions.
Keep the manual in order to be able to refer to it in case of any open questions in the
future. Descriptions, figures, and technical data can change because of technological
advancement. Hence, we advise you to download the latest PDF-version of this
manual from our homepage.
Disclaimer
This manual was prepared with greatest care. If you notice omissions or
inaccuracies, please inform us about these. LUPUS-Electronics GmbH assumes no
liability for technical or typographical faults and reserves the right to make
modifications to the product or user manual without a previous announcement at any
time. The company is not liable or responsible for direct and indirect subsequent
damages which are caused in connection with the equipment, the performance, and
the use of this product.
Not guarantee for the content of this document is taken.
Important safety advice
The warranty will expire for damage due to non-compliance with these operating
instructions. LUPUS-Electronics will not be liable for any consequential loss!
LUPUS-Electronics will not accept liability for damage to property or personal injury
caused by incorrect handling or non-compliance with the safety-instructions. In such
cases the warranty will expire.
Important Note
Please read the manual carefully and completely before you use the camera.
This should also be noted when this product is passed on to a third party.
4
Notes for usage and installation
This camera is a high quality surveillance device. Please keep the following security
information in mind:
Do never angle the camera directly into the sun.
Do never angle the camera directly into a spotlight.
Handle with care. Strong vibrations or impacts could damage the camera.
Never tough internal components of the camera.
Do not install the camera close to any strong electrical wires. This could
influence the quality of the images.
Do not install the camera directly on an aluminium or iron pole. You need to
insulate it with rubber coating. Otherwise, the video transmission can be
disrupted.
Keep in mind that the cameras are not designed to be operated in areas with
extreme temperature and moisture conditions. Adhere to the limits specified in
the technical data stated on our homepage.
This device is not designed to be handled by persons (including children) with
limited physical, sensorial, or mental abilities, as well as, persons who are
lacking the necessary knowledge. Only if they are supervised or instructed by
someone responsible for their security, these persons should handle this
device. Children should be supervised in order to make sure that they do not
play with the device.
Do not leave packing material lying around. Plastic bags, sheeting, etc. can
pose a danger to children if played with. The camera includes cables which
can could lead to strangulation if handled improperly. The camera contains
small parts which could be swallowed, and should be kept out of reach of
children for safety reasons. Install the camera in a position in which children
cannot reach it.
Please pay attention to the safety information and user guides of the other
connected devices.
Adhere to the operating voltage limits specified in the technical data. Higher
voltages could destroy the device and pose a health risk (electric shock).
5
In case you encounter an error
In case you encounter an error, disconnect the camera from its power source and
contact your distributor. Additional usage increases the danger of a fire or of an
electrical shock.
Designated use
When you install the camera make sure that you do not violate the personal rights of
others. Any usage which is not described in this manual is not allowed and leads to a
loss of warranty, as well as, a decline of liability. This also includes modifications.
1. General Introduction
1.1. Overview
The LUPUS GEODOME – LE 337HD and 338HD conform to the HD-CVI standard.
They support long distance, high speed video signal transmission without any delay.
They can be controlled by DVRs conforming to the HD-CVI standard.
1.2. Features
High-performance CMOS image sensor.
Supports coaxial HD video transmission.
Supports 75-3 coaxial cable transmission without any quality loss.
Transmission range:
GEODOME – LE 337HD ~500m / 546 yards
GEODOME – LE338HD ~ 300m / 338 yards.
Long distance, high speed transmission in real time.
Supports HD-CVI output in HD quality.
The GEODOME – LE337HD supports framerates of 25 and 50 frames per
second in 720P.
6
The GEODOME – LE338HD supports framerates of 25 frames per second in
1080P. Additionally, the GEODOME – LE 338HD can also be operated in
720P mode and then supports framerates of 25 and 50 frames per second.
Supports high performance noise reduction.
Performs excellently in low illumination.
Supports ICR switch to allow surveillance by day and by night.
Night-vision:
GEODOME – LE 337HD max. range of 20m / 22 yards
GEODOME – LE 338HD max. range of 30m / 33 yards
Focal length: GEODOME – LE 337HD 3.6mm (fixed lens)
GEODOME – LE 338HD 2.7 – 12mm (manually adjustable)
Protection class: IP66
Features an OCD (on-screen-display) to allow individual setup.
Runs on a DC 12V power supply.
2. Framework and Dimensions
2.1. GEODOME – LE 337HD / 338HD
Please refer to the following figures for dimension information. All measurements are
given in mm.
Figure 2-1 GEODOME - LE 338HD Dimensions
7
Figure 2-2 GEODOME – LE 338HD Layout
Figure 2-3 GEODOME – LE 338HD Layout and connectors
Figure 2-4 GEODOME – LE 337HD Dimensions
8
Figure 2-5 GEODOME – LE 337HD Layout and connectors
3. Installation
IMPORTANT:
Before you install the camera, please make sure that the surface on
which you install the camera can at least support 3x the weight of the
camera.
3.1. GEODOME – LE 338HD
The camera is usually installed on the ceiling, but can be installed on a wall as
well.
If you want to lead the cables out of the side of the camera, please make sure
that the cable exits via the cable exit at the side of the camera as shown in
figure 3-1.
Do not remove the electrostatic film before you finish the installation and make
sure that you do not scratch the dome cover after you removed the film.
9
Figure 3-1 GEODOME – LE 338HD Installation
Step 1:
Use the positioning map to mark the location at which you want to install the camera.
Mind the camera’s cable exit. Drill three holes according to the positions marked in
the positioning map and then push the three dowels into these holes.
Step 2:
Use the inner hex wrench to remove the screws of the dome’s casing.
Step 3:
Adjust he camera position according to fit your drillings. Lay the cable according to your
preference, either through the wall behind the camera, or along the wall next to the
camera (we recommend to lay the cables through the wall behind the camera). Put the
three screws through the holes of the camera into the dowels and then securely fix them.
Step 4:
Adjust the camera’s angle. By tightening the screws (see Fig. 3-2) you can lock the
selected angle.
10
Figure 3-2 GEODOME – LE 338HD
Step 5:
Screw the dome enclosure back onto the camera.
Step 6:
Connect the camera with your HDTV recorder by means of a coaxial cable.
Step 7:
Connect the mains adapter to the camera.
The camera will boot and after a brief period, you will see the live image.
11
3.2. GEODOME – LE 337HD
Figure 3-3 GEODOME – LE 337HD Installation
Step 1:
Use the wrench to loosen the three screws from the side of the camera (Fig. 3-4).
Then, unscrew the screwable mount from the base of the camera.
Figure 3-4 GEODOME – LE 337HD unfasten these screws to install and adjust the camera
Step 2:
Pull the cable through the opening in the camera’s base and lay the cable according to
your preference (we recommend to lay the cables through the wall behind the camera).
Then use four screws to fix the base to the chosen position.
12
Figure 3-5 GEODOME – LE 337HD Installation and connectors
Step 3:
Screw the camera back onto the base. Adjust the camera according to your
preferences and tighten the three screws at the side of the camera again to secure
the chosen adjustment.
Step 4:
Connect the camera with your HDTV recorder by means of a coaxial cable.
Step 5:
Connect the mains adapter to the camera.
The camera will boot and after a brief period, you will see the live image.
13
4. OSD-menu It is possible change camera settings via the OSD menu. Factory-provided, the camera has
the optimal settings to ensure a best possible image. However, if you want to change some
settings, please proceed as follows.
To open the OSD menu, right click on the image while in single picture mode. In the
Menu click on “Pan / Tilt / Zoom.” The following Menu should appear:
Figure 4-1 OSD menu
Click on the arrow at the right edge of the menu. In the expanded menu, click on
“Enter menu” button in the upper right corner. In the following menu, click on enter to
open the OSD menu.
To open the OSD menu via the Web interface of your HDTV recorder, please proceed as
follows:
Open the single image view of a camera and click on the black bar on the right to
open the PTZ options
Select “PTZ menu” and click on the middle button of the directional pad.
Figure 4-2 OSD menu (Web interface)
14
4.1. OSD-menu overview
If you are not familiar with the function of the following settings, we advise you not to
change any settings in the OSD menu!
Format PAL
NTSC
Video Mode 1080p @25 FPS (nur LE 338HD)
720p @ 20 FPS
720p @ 50 FPS
Backlight Mode Off
BLC On
Off
WDR 0 – 5
HLC 0 – 5
Image Adjustment
Image Mode Standard
Soft
Vivid
Sharpness 0 - 100
Brightness 0 - 100
Contrast 0 – 100
Saturation 0 – 100
Sharp suppression 0 – 100
Chroma suppression
0 – 100
Gamma 0 – 15
2DNR 0 - 100
3DNR 0 – 100
Exposure Auto Gain max 0 – 100
Gain min 0 – 100
Low Noise Gain max 0 - 100
Low Motion Blur Shutter max 0 – 40ms
Manual Shutter 1/25 – 1/10000
Gain max 0 – 100
Gain min 0 - 100
Exposure level 0 – 14
Exposure speed 0 – 7
Anti-flicker Outdoor
50Hz
60Hz
White balance Auto
Manual Blue gain 1 – 100
Red gain 1 – 100
Day
Night
15
Indoor
Outdoor
Day / night Auto
B/W
Color
Language
Advanced Camera title
Mirror Horizontal mirror
Vertical mirror
D-Zoom 1 – 10
Lens type Manual
DC
Self-adaption On
Off
Smart IR Auto Level 0 - 10
IR normally closed
Privacy mask Off
on Area selection
Display
Area setup
Restore default
RS485 Setup Address
Apply
System information Version
Reset
Exit
16
Note:
This manual is for reference only. Slight differences may be found in
your user interface.
All designs and software shown here are subject to change without any
prior written notice.
All trademarks and registered trademarks mentioned are the properties
of their respective owners.
If there is any uncertainty or controversy, please refer to the final
explanation of us.
Please visit our website or contact your local service engineer for more
information.
LUPUS-Electronics® GmbH Otto-Hahn-Str. 12, D-76829 Landau
Tel. +49 (0) 6341 93 55 3 0 Fax. +49 (0) 6341 93 55 3 20
E-Mail: [email protected]
www.Lupus-Electronics.de