lta data sheet
TRANSCRIPT
LTA SeriesP R E C I S I O N M O T O R I Z E D A C T U A T O R S
LTA actuators are designed to fit into existing manual stages and other opto-mechanicalcomponents directly replacing manual micrometers. The LTA series features a space-savingdesign that reduces the actuator length by 50% and minimizes the unwanted effects ofcantilever loads on micro-positioning equipment. The non-rotating tip prevents wear andavoids periodic motion variations which can be caused by variable contact between a rotatingtip and its mating surface.
Precision motion is accomplished through a miniature DC servo motor with optimized outputtorque. This allows for faster motion and high load capacity. The LTA-HL is recommended forheavy load applications. It features a robust, 8 mm diameter rod and a M12-0.5 mountingbezel that is compatible with the UMR8 and MVN80 linear stages. The LTA-HS is optimizedfor high-speed applications and provides a longer travel range. The mounting interface of theLTA-HS is compatible with a large number of both Newport and non-Newport manualcomponents.
The LTAHSPPV6 and the LTAHLPPV6 were designed specifically for vacuum applications up to10-6hPa. These are comparable to the LTA-HS, and the LTA-HL respectively, but feature aminiature stepper motor with an encoder for reliable positioning.
Common to all models is a movable limit switch that prevents over-travel. The switchpositions can be changed in minutes to adjust the maximum travel position. A manualadjustment knob permits quick positioning of the actuator when the motor is off. A scaleindicates coarse actuator position in both millimeters and inches.
For compatibility with other Newport manual stages or opto-mech products, refer to themotorized actuator section of www.newport.com.
• Up to 50 mm travel in a space saving design
• Non-rotating tip improves motion smoothness and has nowear
• Exceptional Minimum Incremental Motion
• Adjustable limit switch prevents damage from over-travel
• Convenient manual positioning knob
• Vacuum versions with encoders
The LTA Series actuator is compatible with most standardNewport manual stages and opto-mechanical componentslike the 426 Series translation stage.
LTAxxPPV6 vacuum compatible actuators.
F o r M o t i o n , T h i n k N e w p o r t ™
GUA
RANTEED
SPECIFICATIO
NS
RoHSCompliant
DS-081104
Complete listings for all global office locations are available online at www.newport.com/contact
www.newport.comNewport Corporation, Global Headquarters1791 Deere Avenue, Irvine, CA 92606, USA
PHONE: 1-800-222-6440 1-949-863-3144 FAX: 1-949-253-1680 EMAIL: [email protected]
PHONE EMAILBelgium +32-(0)0800-11 257 [email protected] +86-10-6267-0065 [email protected] +33-(0)1-60-91-68-68 [email protected] +81-3-3794-5511 [email protected] +886 -(0)2-2508-4977 [email protected]
PHONE EMAILIrvine, CA, USA +1-800-222-6440 [email protected] +31-(0)30 6592111 [email protected] Kingdom +44-1235-432-710 [email protected] / Austria / Switzerland +49-(0)6151-708-0 [email protected]
Newport Corporation, Irvine and Santa Clara, California and Franklin, Massachusetts;Evry and Beaune-La-Rolande, France; Stahnsdorf, Germany and Wuxi, China haveall been certified compliant with ISO 9001 by the British Standards Institution.
Ordering InformationModel DescriptionLTA-HS High Speeed Motorized Actuator, 50 mm travel, 3/8-40 thread, LTA Series
LTA-HL High Load Motorized Actuator, 25 mm travel, M12 thread, LTA Series
LTAHSPPV6 Vacuum Compatible High Speed Motorized Actuator, 50 mm travel, LTA Series
LTAHLPPV6 Vacuum Compatible High Load Motorized Actuator, 25 mm travel, LTA Series
LTA-M12 Mounting Adapter, M12-0.5, LTA-HS to UMR8, MVN80 and SL products
Recommended Motion Controllers/Drivers:XPS Order the XPS-DRV01 separately
ESP301
SMC100CC LTA-HS and LTA-HL only
SMC100PP LTAHLPPV6 and LTAHSPPV6 only
CONEX-CC Included in CONEX-LTA-HS or CONEX-LTA-HL
DimensionsModel LTA-HS
4.63 (117.5).89(22.5)
1.77(45)
.79 +0.0120
(20 +0.3)0
ø .63(Ø 16)
CABLE LENGTH 5.8 FT (3 M) AND25-PIN SUB-D CONNECTOR
LTA-HS RODLTA-HL ROD
.39 (10)
BALL ø.19 (Ø 5)
.52 ±0.012
(13.3 ±0.3).47(12)
(M12 x 0.5 THD)
.88 ±0.012
(22.4 ±0.3).62
(15.8)
.19 (5)
3/8”-40 UNS THD
BALL ø.19 (Ø 5)
ø .375
(Ø 9.53 )-.005-.014
-.00019-.00055
Model LTA-M12
.55 (14)
.47 (12)
.88 (22.3)
.18 (4.5)
(M12 x 0.5 THD)ø .25 (Ø 6.4) NUTø .61
(Ø 15.5)
See our websitefor CAD filesCAD
Design DetailsBase Material Stainless steel body
Drive Mechanism Non-rotating lead screw
Feedback Motor mounted rotary encoder, 48 cts/rev.
Limit Switches Optical switches, both ends, adjustable
Origin Uses minimum travel limit for homing, typically <4 mm repeatability
Motor LTA-HS, LTA-HL: DC Motor
LTAHSPPV6, LTAHSPPV6: Stepper Motor
Cable Length LTA-HS, LTA-HL: 3 m
LTAHSPPV6, LTAHLPPV6: 1.5m, SubD25 connector not vacuum compatible.
Vacuum Compatibility 10e-6 hPa (0.7 10e-7 torr)
MTBF 10,000h at half load and with a 10% duty cycle
Weight [lb (kg)] 0.77 (0.35)
SpecificationsLTA-HS LTA-HL LTAHSPPV6 LTAHLPPV6
Travel (mm) 50 25 50 25
Minimum Incremental Motion5 (mm) 0.1 0.05 0.08 0.08
Uni-directional Repeatability, Guaranteed 1 (mm) 0.5 0.5 0.5 0.6
Bi-directional Repeatability, Guaranteed1, 2 (mm) 2 or ± 1 2 or ± 1 2 or ± 1 2 or ± 1
On-Axis Accuracy, Guaranteed1 (mm) 15 or ± 7.5 8 or ± 4 10 or ± 5 5 or ± 2.5
Maximum Speed (mm/s) 5 1 0.5(4) 0.25(4)
Axial Load Capacity (+Cx) (N) 50 120 40 100
Side Load Capacity3 5 N 20 N 5 N 10 N1 Shown are peak to peak, guaranteed specifications or ± half the value as sometimes shown. For the definition oftypical specifications which are about 2X better than the guaranteed values, see page 1386.2 After backlash compensation3 Avoid side loads during motion4 With SMC100PP: 0.1 mm/s - LTAHLPPV6 and 0.2mm/s - LTAHSPPV65MIM in closed loop: 0.15um - LTAHLPPV6 and 0.3um - LTAHSPPV6