low voltage low power constant - g m rail to rail cmos op-amp with overlapped transition regions...
TRANSCRIPT
Low Voltage Low Power constant - gm Rail to Rail CMOS Op-Amp with
Overlapped Transition Regions
ECEN 5007
9/3/02
Vishwas Ganesan
Motivation
Low Supply Voltage Operation Constant gm
Low power consumption making it suitable for portable applications.
Reduced chip area.
Why this paper came up ?
Complementary differential pairs operate in parallel.
This leads to one pair turned on and one off when input is near rails and both pairs on at the middle of the input range leading to gm being twice the value than the former case
Other Circuit Proposals
1. Variation in the tail current in the differential paper doubling gm when only one pair is active.
2. Comparing currents from p and n differential pairs and the maximum current between them is selected and processed for gm constant by maximum-selecting circuitry.
3. Current bleed circuits
4. Square root circuit
Difficulties with other circuits
Increase in slew rate due to increase in tail current.
Extra circuitry – Signal processing circuits and many more current mirrors.
All this leads to complication, Power consumption and more die.
Complementary Input Stage Gm is constant if √ (βnIsn) + √ (βpIsp) = constant
Cutoff : Isn = 0 Vss ≤ Vcm ≤ Vn-
Transition Isn = Isn ( Vcm ) Vn- < Vcm ≤ Vn+
Saturation Isn = ßMBn ( VGMBn – Vss – Vt n) 2
Vn+ < Vcm ≤ Vdd
General Transition graph
This shows the transition region overlap of a general n-p differential pair.
DesignLower boundary of the transition region : Vn
- = Vss + Vtn + VDSMBn Neglecting VDSMBn we get Vn
- ≈ V ss + Vtn Upper boundary of the transition region VDGMBN = - Vtn
VDGMBn = Vn+ - Vtn - √(I sno/ßM1n) – VGMBn
We get Vn
+ = VGMBn + √ (I sno/ ßM1n) Deriving expression for Isn :
Isn = ßM1n ( Vcm – VDMBN – Vtn ) 2 eqn 1
Isn = ßMBn ( VGMBn – Vss – Vtn – VDMBN – Vss ) ( VDMBn – Vss ) Assuming ßMBn = 2 ßM1n and solving for VDMBn from above VDMBn =Vcm+VGMBn– Vtn –½√ [2( -Vtn+VGMBn-Vss)
2 –(Vcm-VGMBn)2]
Using this in eqn 1 Isn=ßM1n[(Vcm–VGMBn)/2+1/2√(2( -Vtn+VGMBN–Vss)
2 –(VCM-VGMBn)2)2
Design
Similarly for Pmos Vp
+ = Vdd + Vtp Vp
-=VGMBp - √Ispo/ßM1p Isp=ßM1p[(-Vcm+VGMBp)/2+1/2√(2(Vtp–VGMBP+Vdd)
2–(VCM-VGMBp)2]2
To overlap the transition regions of the n and p pairs we equate Vp
- = Vn- and Vn
+ = Vp+
Also we assume symmetry between the pairs and so Ispo = Isno , ßM1p = ßM1n , VGMBn = - VGMBp and Vtp = - Vtn
Solving we get ßM1n = ßM1p = Isno/(Vdd + Vtp – VGMBN)2
Complementary Input Stage with DC Level Shifter
Use a dc level shifter to shift the
p-transition curve leftward to overlap the n-transition curve.
Vshift small gm exceeds normal limit Vshift large gm drops below limit ∆ Voptimal yields constant Gm 2VGMBN<∆Voptimal< 2VGMBN+ √(Isno/βM1)
Plot Of gm vs Vcm
OPAMP Circuit
OPAMP Implementation
DC level shifters implemented by 2 pairs of PMOS source followers MS1-MS4
Three stages
1. Complementary input stage
2. Folded cascoded stage M21-M28 provides high gain
3. Class AB output stage M30-M33
4. MB1 and MB11 are biasing transistors.
Frequency Response
Amplitudes and phase plots show unstability due to varying gm.
My simulation results
Input offset voltage 30 mV
Power dissipation .36 mW
Output Voltage swing 1.1 V to -1V
Simulation plots
Paper Results
Input offset voltage 3 mV
Power dissipation .31 mW
OpAmp area .12 mm2
Output Voltage swing Vss + 0.04 to Vdd – 0.07 V
Conclusions
DC level shifters can be used to overlap transition regions to obtain constant gm.
Low Power dissipation was achieved Low supply voltages . There is considerable gain achieved
leading to CMRR improvement.