low profile chest rig operator’s manual
TRANSCRIPT
EQUIPMENT INFORMATION
01 SYSTEM COMPONENTS
OPERATOR INSTRUCTIONS
05 ZIPPER ORIENTATION
06 REAR ASSEMBLY / ADJUSTMENT
07 HARNESS ATTACHMENT / ADJUSTMENT
CONTENTS
1 LOW PROFILE CHEST RIG
INTRODUCTIONThe Low Profile Chest Rig is a simple method for carrying gear
close to the body. Intended for use under an outer garment. Our
patent-pending dual-layer Skeletal™ Cummerbund allows items to
be mounted on the inside face and held tightly against the body.
Stretch back allows for chest expansion while still keeping gear held
tight. Zip front for easy don/doff. Made in the US from US materials.
FEATURES � Dual-layer Skeletal™ Cummerbund
� Zip front for easy don/doff
� Holds gear close to body for concealment under an outer garment
2SYSTEM COMPONENTS
COMPONENT DESCRIPTIONS
3
2
1
5
3 REAR STRETCH PANEL
2 LEFT SKELETAL™ CUMMERBUND
RIGHT SKELETAL™ CUMMERBUND
1 LOW PROFILE HARNESS5
ELASTIC CORD4
4
5 LOW PROFILE CHEST RIG
ZIPPER ORIENTATIONThe zipper on the Skeletal™ Cummerbund is oriented from top to bottom for easy don and doff access.
The zipper should be oriented as shown above.
6OPERATOR INSTRUCTIONS
REAR ASSEMBLY / ADJUSTMENTTo adjust the chest rig for proper fit, complete the following steps:
Route one side of the 3-BAND SKELETAL™ CUMMERBUND through
the vertical webbing slots on the REAR STRETCH PANEL. Insert the
vertical snap tabs through desired horizontal webbing slot on the
cummerbund and snap closed.
Route the ELASTIC CORD through the end slots on the cummerbund
and secure with an overhand knot.
Tuck tab ends under the center webbing slot as pictured above.
Repeat this process on the opposite side.
For smaller adjustment, the cummerbund webbing can be
overlapped and secured as shown in the image above.
1
3
2
4
7 LOW PROFILE CHEST RIG
HARNESS ATTACHMENT / ADJUSTMENTTo adjust the harness for proper fit, complete the following steps:
Route the harness webbing behind the cummerbund and then up
and through the horizontal slots.
Repeat the previous steps for the other side of the cummerbund.
Secure the end of the webbing by routing the end of the strap
through the tri-glide and then back down on itself.
The front of the harness can be assembled in the same manner as
the rear.
1
3
2
4
ABOUT USCrye Precision designs and manufactures
truly innovative equipment for America’s
fighting forces. We are proud and
honored to serve our customers' needs.
We spend as much time as we can with
users, continuously incorporating their
experience and feedback into the gear.
We give them our full support and are
indebted to them for their service and
their sacrifice. We make uncompromising
gear for uncompromising individuals.
We work hard to provide smart, high-
performance, long-wearing gear for people
who demand the best. We make all of our
gear in America from American materials.
Every item is designed to help you
perform better.
WARRANTYIf a defect in materials or workmanship
is found in any of our products, we will
repair or replace it, free of charge, for
the lifetime of the product. This excludes
normal wear and tear. Be aware that
the customer is responsible for any
and all return shipping charges. This
applies to the original purchaser and is
nontransferable.
BODY ARMORIt is against Federal Law for a person
convicted of a violent felony to purchase
or possess body armor. In addition,
various states also have laws restricting
the purchase or possession of body
armor by persons convicted of certain
felonies, other crimes of violence, or drug
crimes. By purchasing body armor, you
acknowledge and certify that (i) you have
no felony convictions, (ii) you have not
been convicted of any other crime that
would restrict your ability to purchase or
possess body armor under any Federal or
State law, (iii) you do not intend to use
the body armor for any criminal purpose
and (iv) you are over 18 years old. Crye
Precision reserves the right, in its sole
discretion, to refuse to sell body armor
to any person. Additionally, the sale of
body armor to residents of Connecticut is
restricted to in-person sales, unless the
sale is made to certain law enforcement
or military personnel. We require that all
orders of body armor be accompanied by
a government issued photo identification.
CONTACT INFOCrye Precision LLC
Brooklyn Navy Yard
63 Flushing Ave Unit 252
Brooklyn, NY 11205
Phone: 1.718.246.3838
Fax: 1.718.246.3833
www.cryeprecision.com
COPYRIGHT© 2014 Crye Precision LLC. Skeletal™
and the ‘CP’ logo are trademarks of Crye
Precision LLC.
REV 051414