low energy operator dorma ed800 - yahoo · doors easy to open while providing sufficient closing...

DORMA ED800

Low Energy Operator

Symbols and Abbreviations

. . . . . . . . . . . . . . . Universal accessibility symbolA156.4 . . . . . . ANSI standard for door controls/closersA156.10 . . . . . . . . . . . . . . . ANSI standard for power

operated pedestrian doorsA156.19 . . . . . . . . ANSI standard for power assist and

low energy power operated doorsABS . . . . . . . . . . . . . . . Acrylonitrilebutadiene styreneADA . . . . . . . . . . . . . . Americans with Disabilities Act

. . . . . . . American National Standards Institute. . . Builders Hardware Manufacturers Association

DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct currentFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frame switchft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FeetHH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand HeldHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HertzJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jamb/top jambKC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Key Chainlbf . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pounds forcelb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PoundsM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main armmA . . . . . . . . . . . . . . . . . . . . . . . . . . . . Milliamperesmm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MillimetersMS . . . . . . . . . . . . . . . . . . . . . . . . . . . Motion SensorNFPA . . . . . . . . . . National Fire Protection AssociationPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Cordpg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PagePS . . . . . . . . . . . . . . . . . . . . . . . . . . Presence SensorR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular armRFR . . . . . . . . . . . . . . . . . . Radio Frequency ReceiverRFT . . . . . . . . . . . . . . . . Radio Frequency TransmitterRS . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote SwitchT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Track

. . . . . . . . . . . . . . . . . . . Underwriter’s Laboratories. . . . . . . . . . . Underwriter’s Laboratories of Canada

VAC . . . . . . . . . . . . . . . . . . . Volts Alternating CurrentVDC . . . . . . . . . . . . . . . . . . . . . . . Volts Direct CurrentWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wall Switch

Table of ContentsDORMA ED800

2

Technical InformationTechnical Details and Certification/Specifications . . . . . . . . . 3Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 4Fire Door Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Operation and Components. . . . . . . . . . . . . . . . . . . . . . . . . 4Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Parts and Assembly DetailsTS83 Door Closer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Transformer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Permanent Magnet DC Motor . . . . . . . . . . . . . . . . . . . . . . . 6Gear Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6External Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Power Open Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 6On/Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Hold Open Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Push & Go Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Power Assist/Low Energy Switch . . . . . . . . . . . . . . . . . . . . . 6Status Indicator Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Incoming Power Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Cooling Fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Technical DrawingsTop Jamb Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Top Jamb Drop Installation . . . . . . . . . . . . . . . . . . . . . . . . . 7Top Jamb Drop Installation x 830 Plate . . . . . . . . . . . . . . . . 8Track Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Accessories800 WS-1 Wall Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9800 WS-1 LOGO Wall Switch . . . . . . . . . . . . . . . . . . . . . . . 9800 WS/RFT-1 Wall Switch (wireless) . . . . . . . . . . . . . . . . . 9800 WS/RFT-1 LOGO Wall Switch (wireless). . . . . . . . . . . . . 9800 FS-1 Frame Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 9800 FS-1 LOGO Frame Switch . . . . . . . . . . . . . . . . . . . . . . 9UMB Universal Mounting Box . . . . . . . . . . . . . . . . . . . . . . . 9800 UMB/RFT Universal Mounting Box . . . . . . . . . . . . . . . . 9UMB Flush MNT Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9800 HH/RFT-1 Hand Held Transmitter. . . . . . . . . . . . . . . . 10800 HH/RFT-2 Hand Held Transmitter. . . . . . . . . . . . . . . . 10800 KC/RFT-1 Key Chain Transmitter . . . . . . . . . . . . . . . . 10800 KC/RFT-2 Key Chain Transmitter . . . . . . . . . . . . . . . . 10800 RFR Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10800 MS-1 RV1 Motion Sensor . . . . . . . . . . . . . . . . . . . . . 10800 PS-1 Presence Sensor. . . . . . . . . . . . . . . . . . . . . . . . 10800 PS-1 RMT Presence Sensor Remote . . . . . . . . . . . . . . 10Transformer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10800 PC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11RS Remote Switch Option . . . . . . . . . . . . . . . . . . . . . . . . 11C886 Regular Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11C800M Regular Arm and Adjusting Arm . . . . . . . . . . . . . . 11C805R Regular Arm Shoe and Bar . . . . . . . . . . . . . . . . . . 11C800R Regular Arm Shoe and Bar . . . . . . . . . . . . . . . . . . 11C810R Regular Arm Shoe and Bar . . . . . . . . . . . . . . . . . . 11C812R Regular Arm Shoe and Bar . . . . . . . . . . . . . . . . . . 11ED-T Track Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11870 Angle Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Patents: 5,913,763/5,956,249/5,687,507

830 Drop Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12831 Drop Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Application Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

The quality managementsystem at the Reamstown,PA facility is certified toISO-9001.*

*DORMA Door Controls Inc., dba: DORMA Architectural Hardware

Low Energy OperatorsDORMA ED800

3

The ANSI A156.19 DORMA ED800is a surface closer based low energypower operator that preciselysenses the door environment andresponds appropriately. TheED800 is designed for manualopenings that occasionally requireautomatic opening.The Americans with Disabilities Act (ADA) heightened awarenessthat doors present barriers to individuals with physical challenges.A major concern of door closer manufacturers is how to makedoors easy to open while providing sufficient closing force.Interior doors pose a few problems, while exterior doors areexposed to a much wider array of forces. Closers with adjustablespring power can help, but cannot guarantee compliance, whenthe adjustment must be increased in order to close the door.

DORMA has solved these problems with the ED800. It fulfillsthe need for constant reliable closing control of doors whileproviding the power to open them as needed for the physicallychallenged.

Technical Details:• TS83 Series door closer with adjustable spring power, sweep

speed, latch speed and backcheck cushioning.• Non-handed.• Accommodates doors 36"/100 lb to 48"/200 lb• Push/Pull switch allows one unit for track and top jamb

applications.• Low Energy/Power Assist selector switch.• Strike delay on/off switch.• Push & Go on/off switch.• Delay time, opening time/opening force, opening angle and

door width selector adjustments for powered operation.• Heavy-duty, aesthetically pleasing and easy to adjust steel

arm assembly.• Status light for diagnostic purposes.• A full complement of accessories available for specific job

requirements.

Adjustable Spring Size (manual/powered operation) 3–5

Controlled Closing with two adjustment valves 115º–15º(manual/powered operation) 15º–0º

Adjustable Backcheck (manual operation) •

Delay Time, Opening Time/Opening Force, OpeningAngle, Door Width Selector (powered operation) •

Radio Frequency Activation ••

Push & Go (door movement activates operator) •

Electric Strike or Latch Retraction Control •

Vestibule Function (sequenced operation of of two operators) •

12 VDC Output for Powering Accessories •

• yes •• option

Features

Certification:The DORMA ED800 Series is listed by U.L. and C.U.L. undertheir continuing reinspection programs. The ED800 Series isBHMA certified to the requirements of ANSI A156.19 Grade 1for power assist and low energy power operated doors. Meetsthe requirements for UL10C and UBC 7.2 (1997) for positivepressure.

Specification:DORMA ED800 Series low energy operators with selectable lowenergy or power assist. Low energy function to cycle the dooropen as prescribed by the four user adjustments. Power assistfunction to require manual opening with an adjustable forcebetween 1/2 lbf and 5 lbf. All operators to have push & gofeature to activate low energy or power assist with the door. Alloperators to have door closer function when low energy or powerassist is not required. Door closer to have adjustable springsize, valve adjustable sweep speed, latch speed, and backcheckcushioning. All operators to have the following user adjust-ments for power open functions: delay time, openingtime/opening force, opening angle, and door width selector.Operators to have selectable slide switch to accommodate pushor pull side applications. Operators to have on/off strike delayswitch when the ED800 must delay while a locking devicereleases. Push side (top jamb) and pull side (track) arms to beavailable. Operators to have vestibule function for sequencingoperation of two units. Operators to have a selectable fiveminute hold open. All operators will be hard wired.

Optional Specifications:All operators to have remote switch wiring for tamper-resis-tance. Hold open function is deleted. On/off status can becontrolled from a remote location. Specify RS.

All operators to be powered with a power cord plugged into a120 VAC receptacle. Specify PC.

Technical InformationDORMA ED800

4

Electrical Specifications:Power requirements: 120 VAC , 50/60 Hz.

Current: 2 Amp.

Fuse: 3 Amp - type AGC - size 1/4"–1-1/4".

Auxiliary power output: 12 Volts (nominal) filtered, unregulated@ 500 mA max. Range 10–25 VDC.

Form “C” relay contact for controlling fail-secure or fail-safelocking devices: 50 VAC or DC at 1 Amp max.

When incorporating the ED800 into a system with other electri-cal components, DORMA’s Technical Services Departmentoffers assistance with point to point wiring diagrams. Pleasecontact them with specific requirements.

Finishes:Standard Sprayed Finishes:Aluminum: 689.Bronze: 691 (Dull), 690 (Statuary), or 695 (Dark Duranodic).Gold: 696Black: 693.

Optional Special Color Sprayed Finishes: Specify code numberor submit 3 color chip samples.

Optional Plated Finishes: Brass: 605 (Bright) or 606 (Satin).Bronze: 611 (Bright), 612 (Satin), or

613 (Oxidized Satin Oil Rubbed).Nickel: 618 (Bright) or 619 (Satin).Chrome: 625 (Bright) or 626 (Satin).

Fire Door ApplicationsThe ED800 is U.L./C.U.L. listed for installation on labeled fire doors.

Warranty:The ED800 is warranted for a period of two years from the dateof manufacture.

+10%–15%

depending on the userrequirements. If damagefrom severe environmentalconditions or abuse is possi-ble, doors opening beyond115º require an auxiliarystop, supplied by others.

The opening time of thedoor can be set when the ED800 is in the low energymode. It can be adjusted,depending on door width andweight, to meet the require-ments of ANSI A156.19.When the power assist modeis selected, this adjustment isused to determine openingforce. The opening force isadjustable between 1/2 lbfand 5 lbf.

The door width selector isadjusted to match the widthof the door that the unit isoperating (36"–48").

If the ED800 encounters anobstacle, it stops and goes toa balanced state. The door isheld in this condition for thelength of time determined bythe delay setting. The ED800provides an assist functionwhile in the balanced state,making it easier for users topush the door out of the way.The ED800 will again re-enterthe balanced state if theopening has not cleared or if itencounters another obstacle.

The ED800 is a non-handed universal unit. It caneasily be installed by oneperson. Slots in the mount-ing plate permit it to rest onpre-installed fasteners whilesecuring the remainingfasteners.Two mounting applicationsare available. Track mount isa pull side application with asingle lever arm. Top jambmount is a push side applica-tion with a double leveredarm. A drop application oftop jamb

The microprocessor incor-porates three slide selectorswitches and four useradjustments: delay time,opening angle, openingtime/opening force, and door width.

The push and go slideselector switch is used toactivate or deactivate thepush and go feature. Thedoor functions as an actuatorwhen the switch is on.

The power assist/low energyswitch selects the operationalmode of the ED800. The power assist functionresults in the door openingapproximately one inch. Thedoor can then be opened witha reduced force. In the lowenergy mode, the door willcycle to the open position asprescribed by the four useradjustments.

The strike delay switch isused to activate or deactivate adelay of the ED800 operation.When on, it allows time foroperation of the locking devicecontrolled by the form “C”contacts.

The delay time is theamount of time the door waitsbefore closing from maximumopening or when the doordetects an obstacle. Delaytime is adjustable from 5 seconds to 60 seconds.

The opening angle isadjustable from 85º to 115º,

The ED800 is simple toinstall. It is a “low energy”operator and does not requireexternal safety devices. Theopening speeds and forces aretailored to meet the needs ofthe physically challenged.Opening force never exceeds15 lbf. Closing time is neverless than 3 seconds from 90ºto 10º, nor less than 1.5seconds from 10º to closed.

DORMA has achieved atechnological breakthrough. . . an intelligent door closer,designed solely to providesafe, barrier free access. TheED800 goes well beyondbasic requirements to assurecomplete user safety.

The on-board microprocessoris the brain center. It completesan initial learning cycle at thefirst application of power. Thelearning cycle communicatesinformation about the mountingand closing force to the micro-processor. It continuouslymonitors door position, pushingforce, resistance, wind/draftconditions, opening and closingspeeds and other variables. It will detect even the slightestdeviation from the programmednorm and respond immediately.The operating system is continu-ously checked for systemmalfunctions to enhance thesafety and reliability of the unit.

Operation and Components

5

Transformer - accepts 120VAC input line voltage andreduces it to 12 VAC outputto the microprocessor.

Microprocessor - a miniaturecomputer that contains alloperating information for theED800. It constantly evaluatesdata and directs the appropri-ate signals to the motor.

Encoder - reports the doorposition to the microprocessorby monitoring the operation ofthe motor.

Permanent Magnet DC Motor -receives activation signal andpower from the microprocessor.Provides the power to drive thegear assembly.

Gear Assembly - transfers thepower output of the motor tothe linear actuator assembly.

Linear Actuator - drives thelow energy and power assistfunction for door opening.

The ED800 features the TS83 door closer. This ANSI/BHMAA156.4 Grade 1 closer incorporates sweep, latch, backcheck,and adjustable spring power. The TS83 provides closing powerand closing control for the ED800. In the event of a powerfailure or when assistance is not required, the ED800 functionsas a standard door closer.

The ED800 has two field selectable functions: low energyor power assist. The choice is made by moving the slide switchto select the desired function.

Upon activation in the low energy function, the door willcycle to the open position as prescribed by the four useradjustments in the microprocessor and in accordance withANSI A156.19.

Activation in the power assist function results in the dooropening approximately one inch to alert the user that the powerassist has been activated. The door can then be opened with areduced force. The force is adjustable between 1/2 lbf and 5lbf. When power assist is selected, opening force is adjustedusing the opening speed function of the microprocessor. Powerassist remains active as long as there is door movement plusthe time delay setting.

Two ED800 units can be interconnected for a vestibulefunction. This arrangement provides sequenced operation ofthe two units. Activation of either the interior or exterior unitinitiates operation of only that unit. Activation of the secondunit will not occur until the closing cycle of the first unit iscompleted.

The ED800 provides contacts for electric strike release orelectric latch retraction. Activation of the ED800 sends asignal to release the strike or retract the latch. Operation ofthe ED800 is delayed by 1/2 second with the strike delayswitch “on” to allow time for this process. The unit thenoperates normally. Release of the strike or retraction of thelatch is initiated only when the door is closed, preventingunnecessary operation. Additionally, an external output of 12VDC at 500 mA maximum is provided to power a variety ofaccessories.

External safety devices such as mats, guide rails, andsensors are not required with the ED800. However, a safetycircuit is built into the unit. Use of the optional 800 PS-1presence sensor connected to the safety circuit prohibits initialopening of the door if an obstacle is sensed at the time ofactivation. The door will remain in the hold open position aslong as the sensor detects traffic or an obstacle. The door willautomatically default to the power assist mode if it encountersan obstacle after the opening cycle commences. The 800 PS-1requires use of the optional accessory TRANSFORMER forpower and the 800 PS-1 RMT remote control for setup. Seepage 11 for details. For additional transformers offered byDORMA, see page 5 of the PS-500 product brochure.

change requires two things.First, the arms must beexchanged. Second, the slideswitch must be placed at thecorrect position for the armused. These user options makethe ED800 simple to stock.

mount is available for lowceiling conditions. Thisapplication differs only byhow the frame is machined.

The ED800 unit can bechanged from top jamb totrack or vice versa. This

The following are operational components of the ED800.

Technical InformationDORMA ED800

6

1. TS83 Door Closer

2. Transformer

3. Microprocessor

4. Permanent Magnet DC Motor

5. Gear Assembly

6. Hold Open Switch

7. On/Off Switch

8. External Connector

9. Power Open Adjustments

10. Push & Go Switch

11. Power Assist/Low Energy Switch

12. Status Indicator Light

13. Incoming Power Fuse

14. Cooling Fins

5

6

3

11

7

8

10 9

12

4

14

2

1

13

The hold open switch overrides all other inputs and holds the door open approximately 5 minutes. The doorthen closes and the unit returns to normal operation. The doorcan be closed at any time during the 5 minute hold openperiod by pressing the hold open switch in the opposite direc-tion. The ED800 again returns to normal operation.

The on/off switch controls power input to the ED800. In theoff position, the ED800 operates as a standard door closer. Inthe on position, power is applied to the unit. It will firstcomplete a learning cycle and then operate normally.

A remote switch option is available to remove the on/offswitch from the endcap of the ED800. Switching must thenbe provided at a remote location. The hold open switch isdeleted when the remote switch option is specified. Thisoption provides more controlled operation.

Concealed wiring is standard with the ED800. The optional800 PC power cord eliminates the need for concealed wiring.The 15" long power cord will permit the ED800 to plug directlyinto a 120 VAC receptacle.

The ED800 has a field selectable actuator. The door can becomethe actuator. When the switch is set to the on position, the push& go feature is initiated. Push & go activates the ED800 whenthe door is opened more than one inch. It can be used as thesole actuator or in conjunction with other external actuators. TheED800 senses normal operation and aborts the push & go featureif there is a rapid motion that opens the door beyond 45°. Push& go is active only when the door is in the closed position.

NOTE: When the ED800 is placed in an installation wheremoderate to heavy pedestrian traffic will be present, it is recom-mended that the push & go feature be left in the off position.

Hold Open Switch

On/Off

Actuators

Technical DrawingsDORMA ED800

7

Top Jamb Installation

Top Jamb Drop Installation

Size Selection ChartAdjustable spring power for doors 3'0" to 4'0" wide.

REVEAL ARM APPROX. APPROX. APPROX.MAXIMUM BACKCHECK HOLD OPENOPENING RANGE RANGE

0"–4" C800R 115° 62°–115° 85°–115°

2"–6"* C805R 115° 68°–115° 85°–115°

3"–8" C810R 115° 68°–115° 85°–115°

8"–12" C812R 115° 75°–115° 70°–115°

*Standard with ED800 J.

ED800 J

12-3/8(314)

7/8(22)

of 4-1/2" wide hinge, 3/4" offset pivot

Minimum frame face for mounting unit 1-5/8".

21-1/4(540)

2-1/8(54)

3/4(19)

12-3/4(324)

6(152)

4-1/4(108)

Minimum to ceiling 4-3/4"

Maximum stop

Reveal


of 4-1/2" wide hinge, 3/4" offset pivotMinimum frame face for mounting unit 1-3/4".

21-1/4(540)

12-3/4(324)

Reveal

4-1/4(108)

6(152)


4-5/8(117)

7/8(22)

12-3/8(314)

ED800 J - 2"–6" Reveal (standard)ED800 J x C800R - 0"–4" RevealED800 J x C810R - 3"–8" RevealED800 J x C812R - 8"–12" Reveal


A floor or wall stop is recommended to limit door travel to a maximum 115° to prevent possible damage to the ED800 arm.Where this is not practical, the ED800 J x Drop Mount with a surface door stop is recommended.

A floor or wall stop is recommended to limit door travel to a maximum 115° to prevent possible damage to the ED800 arm.Where this is not practical, a surface door stop is recommended.

ED800 J Drop


0"–4" C800R 115° 62°–115° 85°–115°

2"–6"* C805R 115° 68°–115° 85°–115°

3"–8" C810R 115° 68°–115° 85°–115°

8"–12" C812R 115° 75°–115° 70°–115°


8

Top Jamb Drop Installation x 830 Plate

Track Installation

7/8(22)

21-1/4(540)

4-5/8(117)

12-3/4(324)

6(152)


2" Min.top rail

Reveal

4-1/4(108)

12-3/8(314)

of 4-1/2" wide hinge, 3/4" offset pivot

Minimum frame face for mounting unit 1-3/4".

of 4-1/2" wide hinge, 3/4" offset pivot Minimum frame face for mounting unit 2".

21-1/4(540)

25(635)

7/16(11)

6(152)

4-1/4(108)

13/16(21)1-1/4(32)


3-9/16(90)


ED800 J Drop x 830


APPROX. APPROX. APPROX.MAXIMUM BACKCHECK HOLD OPENOPENING RANGE RANGE

105° 70°–105° 85°–105°

ED800 T

A floor or wall stop is recommended to limit door travel to a maximum 115° to prevent possible damage to the ED800 arm.Where this is not practical, a surface door stop is recommended.


A floor or wall stop is recommended to limit door travel to a maximum 105° to prevent possible damage to the ED800 arm.Where this is not practical, the ED800 J x Drop Mount with a surface door stop is recommended.


0"–4" C800R 115° 62°–115° 85°–115°

2"–6"* C805R 115° 68°–115° 85°–115°

3"–8" C810R 115° 68°–115° 85°–115°

8"–12" C812R 115° 75°–115° 70°–115°


Technical DrawingsDORMA ED800

AccessoriesDORMA ED800

9

800 WS-1 — Tamper-resis-tant 6" x 6" wall plate with anormally open switch.Includes a heavy duty injec-tion molded black ABSmounting box. Satin stainlesssteel wall plate with blueengraving. Wall plate displaysthe accessibility symbol and“PRESS TO OPEN.” Fits astandard 4" x 4" electricalbox. Must be hard wired.

Flush design allows theoptimum in weather resis-tance in surface or recessedapplications.800 WS-1 LOGO — Same asthe 800 WS-1, except thatthe wall plate displays theaccessibility symbol only.

800 FS-1 — 1-3/4" x 4-1/2"frame plate with a normallyopen switch. Satin stainlesssteel frame plate with blueengraving. Frame platedisplays the accessibilitysymbol and “PRESS TOOPEN.” Fits a minimum 1-3/4" x 4" frame section.Must be hard wired.800 FS-1 LOGO — Same as800 FS-1, except that wallplate displays the accessibilitysymbol only.

800 WS/RFT-1 — Tamper-resistant 6" x 6" wall platewith a normally open wirelessswitch. Includes a heavy dutyinjection molded black ABSmounting box with a radiofrequency transmitter and 9 VDC battery. Must be usedin conjunction with the 800RFR receiver. Maximumrange is 50 ft. Satin stainlesssteel wall plate with blueengraving. Wall plate displays

the accessibility symbol and“PRESS TO OPEN.” Flushdesign allows the optimum inweather-resistance in surfaceor recessed applications.Ideal where conditionsprohibit hard wiring.800 WS/RFT-1 LOGO —Same as 800 WS/RFT-1,except that the wall platedisplays the accessibilitysymbol only.

Frame Switch

Wall Switch (wireless)Wall Switch

1-3/4(44)

6-5/8(168)

6-5/8(168)

Mounting Box

WallPlate

6-5/16(160)

1/2(13)

6-5/16(160)

1/4(6)

4-1/2(114)

1-3/4(44)

1-3/4(44)

6-5/8(168)

6-5/8(168)

Mounting Box

WallPlate

6-5/16(160)

1/2(13)

6-5/16(160)

800 WS-1 800 WS-1 LOGO

1/4(6)

4-1/2(114)

1-3/4(44)

800 FS-1 LOGO

800 FS-1

800 WSRFT-1 800 WSRFT-1 LOGO

UMB — Black ABS universalreplacement mounting box for800 WS-1 type switches.

Mounting Box

1-3/4(44)

6-5/8(168)

6-5/8(168)

UMB Flush MNT Ring —Black ABS flush mount ringand metal mounting bracket.The ring is designed to coverthe gap between the mount-ing box and the switch platecutout in the wall for a niceclean look.

Flush Mount Ring

3/16(5)

8-1/8(206)

8-1/8(206)

800 UMB/RFT — Black ABSuniversal replacement mount-ing box for 800 WS/RFT-1type switches. Includes aradio frequency transmitter.

Mounting Box

1-3/4(44)

6-5/8(168)

6-5/8(168)

10

TRANSFORMER — 120 VACto 24 VAC, 15 VA step-downtransformer. Fits standard 4" x 4" electrical box.Required with 800 PS-1.Can be used with other accessories.

Transformer

3-1/4(83)

1-3/4(44)

800 RFR — Radio frequencyreceiver. Required for usewith all DORMA transmitterswitches. Powered from the12 VDC accessory output ofthe ED800. Ideal for applica-tions with range and signalstrength problems. Maximumrange typically 50 ft (condi-tions permitting). Surfaceapplies remotely. Operates on12–30 Volts AC or DC. 16 mAnominal (50 mA max. whenrelay is triggered).

Receiver

5-1/4(133)

3-1/2(89)

1-1/2(38)

AccessoriesDORMA ED800

800 MS-1 RV1 — Unidirec-tional K band sensor.Adjustable elliptical sensingpattern. Eliminates need forswitch actuators. Adjustmentsinclude unidirectional, uni -directional with motion trackingfeature, bidirectional sensingcapability, wide or narrowpatterns, 3-dimensional angleadjustment, and heightenedimmunity to highly sensitivemotion settings. Adjustmentsvia 800 PS-1 RMT remotecontrol. Self-monitored readyout of the box, used with orwithout a self-monitored ready

system. Includes 0°–90°vertical and –30°–+30° lateraltilt angle, powered by 12–24VAC±10% or 12–24 VDC .800 PS-1 RMT required forinitial setup. Designed for usein openings designated specifi-cally for barrier-free accessibil-ity. Should not be used incombination with ED800 inopenings used for pedestriantraffic or where high-speedoperation/opening is needed.Precise setup of the motionsensor detection area isnecessary so that nearby trafficis not picked up.

+30%–10%

800 PS-1 — Ties to ED800safety circuit for ultimate userprotection. Prohibits openingof door if obstacle is sensed.Requires use of optionalTRANSFORMER.800 PS-1 RMT — Hand held remote control requiredto program 800 PS-1 or 800 MS-1 RV1. One remoteprograms unlimited presenceor motion sensors.

Motion Sensor Presence Sensor

4-1/2"(114)

2"(51)

3-1/8"(79)

11-1/4(286)

2-1/4(57)

3(76)

800 HH/RFT-1 (SingleFrequency), 800 HH/RFT-2(Dual Frequency) — Com-pact, portable switches. Mustbe used with 800 RFRreceiver. Maximum range isapprox. 50 ft (depending onconditions). Works with, or inplace of, 800 WS/RFT-1.Powered by 9 V DC battery.

Well suited where multipleusers must activate ED800for accessibility, security,convenience, or where use ofan exposed switch is notpractical. Neutral case withgrained finish. RFT-2requires one 800 RFR perfrequency.

800 KC/RFT-1 (Single Fre-quency), 800 KC/RFT-2 (DualFrequency) — Similar to 800 HH/RFT-1 or800 HH/RFT-2, but morecompact. Must be used with800 RFR receiver. RFT-2requires one 800 RFR perfrequency. The small sizepermits the use as a keychain or in cases where thehand held transmitter is toolarge. Powered by a 12 VDCbattery.

Key Chain TransmitterHand Held Transmitters

3-3/4(95)

7/8(22)

3-3/4(95)

7/8(22)

RFT-1 RFT-2

2-1/8(54)

5/8(16)

1-1/2(38)

5/8(16)

RFT-1

RFT-2

11

800 PC — Eliminates needfor hard wiring. Permits ED800 to plug directly into120 VAC/60 Hz receptacle.Cord measures 15" from endcap to center of plug.

RS — Removes on/off andhold open switches fromendcap for tamper resistance.Hold open function is deleted.On/off switch must beremotely located. Switch notprovided. (Illustration depictsappearance of end cap whenRS option is selected).

Power Cord Remote Switch Option

C886 — Standard armfurnished with ED800 Japplications. Non-hold openassembly complete 2"–6" (51 mm–152 mm) reveal.Arm is non-handed.C800M — Main arm andadjusting arm without shoeand bar. Requires use ofC800R, C805R, C810R orC812R shoe and bar.

C805R — 2"–6" (51 mm–152 mm) reveal — Shoe andbar only. Furnished standardwith C886. Non-handed.C800R — 0"–4" (0 mm–102 mm) reveal — Shoe andbar only.

C805R and C800R must beused in conjunction withC800M. Non-handed.

C810R — 3"–8" (76 mm–203 mm) reveal — Shoe andbar only.C812R — 8"–12" (203 mm–305 mm) reveal — Shoe andbar only.

C810R and C812R must beused in conjunction withC800M. Non-handed.

Regular Arm Shoe and Bar

Regular Arm Shoe and Bar

Regular Arm

7/8(22)

6(152)

4-3/16(106)

13(330)

10-1/4(260)

12(305)

Main ArmShoe and Bar

AdjustingArm

C812R

ED-T — Standard arm fur-nished with ED800 T applica-tions. Non-hold open assem-bly complete. Arm isnon-handed.

Track Arm

24(610)

1-3/16(30)14-1/4

(362)

C805R

C800R

18-1/4(464)

C810R

NOTE: Refer to the Accessories section of the Door ControlsPrice List for additional accessories available.

870 — For mounting ED800 Jeasily on deep reveal frameconditions or when frame faceis less than 1-3/4". Frame

must be properly reinforced tosecure bracket. Requires 2-3/4" minimum soffit width.

Angle Bracket

2(51)

3(76)

21-1/4(540)

Subject to change without notice 12.05CT 3M USA 07000303

AccessoriesApplication Profile

DORMA ED800

Operation NarrativeDoor is always operable manually from either side. Operator will be triggered by hand held transmitter and wall mounted wireless switches.Actuation of low energy power operator will retract fire exit device latch bolt before initiating door movement. Retraction will only occurwhen door is closed. Set delay time at 30 seconds. Set operator unit to LOW ENERGY. Set operator PUSH AND GO selector to off.

Hardware Set1 EA Operator ED800 J x 626E DORMA1 SET Pivot Set OPF440 x 626E DORMA1 EA Electric Pivot 75200 x 4 Wire x 626E DORMA1 EA Fire Exit Device with Latch Retraction ES x F9300 x YR08 x 626E DORMA1 EA Power Supply PS501 DORMA1 EA Receiver 800 RFR DORMA1 EA Hand Held Transmitter 800 HH/RFT-1 DORMA2 EA Wall Switches 800 WS/RFT-1 DORMA

Receiver 800 RFR

Hand Held Transmitter800 HH/RFT-1

Wall Switches800 WS/RFT-1

Junction Box

120 VACInput

PowerSupplyPS-501

ElectricPivot

Fire ControlPanel

830 — For mounting arm shoein top jamb drop applicationwhen top door rail is less than4-5/8" (2" minimum required).

831 — For mounting arm shoewhen ED800 J is installed withan 870 angle bracket and topdoor rail is less than 6-1/4" (2"minimum required).

Drop Plate

3-3/8(86)

2-1/4(57)

Drop Plate

5-5/8(143)

2-1/4(57)

DORMA GroupNorth Americawww.dorma-usa.com

DORMA Architectural HardwareDORMA Drive, Drawer ACReamstown, PA 17567-0411Telephone: (800) 523-8483Facsimile: (800) 274-9724E-mail: [email protected]

DORMA Canada1680 Courtney Park Drive,Unit 13Mississauga, Ontario L5T 1R4Telephone: (800) 387-4938Facsimile: (905) 670-5850E-mail: [email protected]

DORMA Mexico, S. de R.L. de C.V.Astrónomos 28Col. Escandón11800, México, D.F.MexicoTelephone: (52+55) 5272-6937Facsimile: (52+55) 5272-6948E-mail: [email protected]

ED800

Example of Typical Operated Opening

low energy operator dorma ed800 - yahoo · doors easy to open while providing sufficient closing...

Documents