The advantages of the pre-insulated tube systems and our experience and knowledge of process tubes are the best base of your process tubes. The possibilities are limitless within a range from -200ºC up to +350ºC. Especially in tube bridges you can reduce costs according to the investment costs, installation time but mainly the energy costs.

The Mix of 4 variable components1. Transport tube: all materials wit a diameter up to

800mm.2. Isolation: Customised materials based on the

temperature of the application 3. Jacket: Choice between 5 robust sorts of

materials. 4. Options: Divers options possible, like tracing,

leak detection etc.

The combination of the chosen variables is the op-timal configuration for your application. The choice depends on the technical and economical input.

Features• 100% waterproof• High mechanical resistance• Effective corrosion protection of the tube• Resistant against chemical products and

UV• Tracing of the tube is possible• Sandwichsystem• Easy installation of the products

Advantages• Well cleanable• Constant isolation during the lifetime• Quick payback time• No source of infection• Less loss of energy• Low maintenance costs

Customised delivery Every application is different. That is why the iso-lation material (based on the temperature and the needed result) is calculated regarding to the size and composition of the isolation material. This can be adapted to your specific needs. The system has some little restrictions but they minor to the enor-mous advantages. Besides the possibility of the standard tube components, SKS can also isolate the short tube installations, skids-fittings or machi-ne parts. We can even produce these products for you if we get a drawing for it. Why should you isolate afterwards when it can be done much better in an optimal situation before-hand?

LOW AND HIGH TEMPERATURESA pre-insulated pipe normally consists of three parts:

• Carrier pipeAt the centre is the carrier pipe, typically a steel pipe of boiler tube quality.

• InsulationThen comes an insulation layer, which in the case of the high temperature system, consists of two part - an inner layer of miniral wool and an outer layer of polyurethane foam (PUR). The mineral wool is intended to protect the PUR insulation against temperatu-res above 140°C.

• JacketOn the outside is a protective jacket of polyethylene (PE) that ensures (once joined accoring to Logstor standards) that moisture can not penetrate the insulation thereby giving a 100% waterproof standard.

HIGH TEMPERATURES

Logstor Safepipe:• Combines key benefits from two technologies• Enables you to detect and monitor leaks before

major damage occurs• Prevents small leaks developing into major spills• Ensures that sensor cables are easy to access,

maintain and upgrade• You can use identical inventory and equipment

for installations above and below ground• Easy to install, saving on time, manpower and

money

SAFEPIPEJacket

PEHMax. 140 °C. Density 60-80 kg/m³

l(50): 0,0275 W/mK

Carrier pipeP235GH/EN10217/2. Welded steel

tubesP235GH/EN10216/2. Seamless steel

tubes

Max. 400 °CDensity ~120 kg/m³l(100): 0,050 W/mK

High temperature system freely suspended above ground.The freely suspended system functions as a bon-ded system (i.e. the jacket and carrier pipe expand at the same rate). Supports may be placed directly onto the jacket. Expansion is normally absorbed by bends and expansion joints.

High temperature system for ground burial (HT3)The buried system functions as a sliding system, i.e. the carrier pipe expands within the insulation without the jacket moving in the ground. Expansion is absorbed within the system by axial compensa-tors or expansion bends.

PUR foam

Impervious HDPE casing that keeps any leakage inside the pipe

Serving pipe of any material

Perforated plastic tube for sensor cable that detects any leaks

Logstor SafePipes enables you to benefit from the combined technology, insight and experien-ce available from the best suppliers in two diffe-rent fields. TraceTek sensor cables and Logstor pipe systems.

Together, they provide a supremely reliable, easy-to-install integrated solution for detecting leakages and preventing spills of all kinds from chemical and petrochemical pipe systems.

Logstor SafePipes are ideal for transporting:• Petrol/gasoline, diesel, jet, fuel, crude oil,

lube oil and other hydrocarbon-based li-quids

• Organic solvents• Strong acids and bases and other hazardous

fluids that contain water• Contaminated water and polluting liquids in

general in a safe, effectively monitored way that makes sure any spills are kept securely within the pipe.

Logstor proactively addresses both quality and environmental concerns from component ma-nufacture to finisched installation. ISO 9001 and ISO 14001 standards are basis for the manufac-ture of all Logstor pipes and components

The two standard insulation series are Series 210 for operating temperatures from 140 °C to 210 °C and Se-ries 250 for operating temperatures from 140 °C to 250 °C.

WWW.SKS-ONLINE.COM WWW.SKS-WEBSHOP.COM

S. K .S. / L O G S T O R

Advisory partnerSales employees at S.K.S. are trained to assist in the choice of isolation for your application. We have equipment engineers whom can still advise or guide you to make your choice as concrete as possible. This advice can be given as a pre-sentation, reference visits or personal interviews.

IntermediateS.K.S. handles the communication from the customers towards Logstor. S.K.S. is the voice of the user, and represents its interests and ideas. In the case of claims or specific issues you can count on S.K.S. to be interlocutor and intermediary towards Logstor.

AvailabilityAs a wholesaler S.K.S. also acts as a classical caregiver of availability. The stock is based on the history of S.K.S. If this does not sync to your needs, S.K.S. is glad to respond to your demands. Logstor is available on request.

DistributionBesides the Logstor package S.K.S. has much more delivery possibilities. This in combination with the logistic capabilities, S.K.S. can anticipate to the needs and requirements of supply and distribution. Due to the efficient customized logistics S.K.S. provides possible cost savings. The customization of the supply starts with the way of ordering and ends when it is on your shelf. Ask our account ma-nagers for the possibilities. We can help to start a customized collaboration.

TrainingsThe main added value S.K.S. offers you is her knowledge of the components, implementation, maintenance and logistics. The at S.K.S. available knowledge usually not involves your core business, but you have the need for this infor-mation to make the right choice. S.K.S. can provide you this knowledge. S.K.S. provides the information in various forms and courses. S.K.S. offers for example courses in the field of materials choice, regulation, standardization, incoming inspection, component selection and maintenance.

Service & MaintenanceS.K.S. offers, besides the obvious warranty on the materials delivered, a broad interpretation on service and maintenance. Although we don’t give a physical interpretation, we offer customized solutions along with our Service Partners.S.K.S. also likes to work with your own maintenance service and we serve as a source of information or logistics organizer.

Contact details

The NetherlandsS.K.S. B.V.Keurweg 2NL-5145 NX WaalwijkPostbus 680NL-5140 AR WaalwijkPhone number: +31 (0)88 - 120 23 00E-mail: sales.nl@sks-online.com

S.K.S. DrachtenDopheide 8cNL-9202 PB DrachtenPhone number: +31 (0)88 - 120 23 90E-mail: drachten@sks-online.com

BelgiumS.K.S. b.v.b.a.Uitbreidingsstraat 66 (bus 17)B-2600 Berchem (Antwerpen)Phone number: +32 (0)323 - 26 332E-mail: sales.be@sks-online.com

GermanyS.K.S. GmbHFlughafenring 11D-44319 DortmundPhone number: +49 (0)231 477939 00E-mail: sales.de@sks-online.com

Revision 06/2018

HYGIENIC TUBE & PROCESS COMPONENTS