losses in fiber optic system chapter 4. signal degradation in the optical fiber signal attenuation...
TRANSCRIPT
LOSSES IN FIBER OPTIC SYSTEM
CHAPTER 4
Signal Degradation in the Optical Fiber
Signal Attenuation- It determines the maximum unamplified or
repeaterless distance between transmitter and receiver.
Signal Distortion
- Causes optical pulses broaden.
- Overlapping with neighboring pulses, creating errors in the receiver output.
- It limits the information carrying capacity of a fiber.
The Basic Attenuation Mechanisms in a Fiber
1. Absorption
It is related to the fiber material
2. Scattering
It is associated both with the fiber material and with the structural imperfections in the optical waveguide.
3. Radiation losses/ Bending losses:
It originates from perturbation (both microscopic and macroscopic) of the fiber geometry.
Absorption
Light travels best in clear substances. Impurities such as metal particles or moisture in the fiber can block some of the light energy, it absorb the light and dissipate it in the form of heat energy, which caused absorption loss.
The solution is to use ultra-pure glass and dopant chemicals to minimize impurities, and to eliminate loss at the peak wavelength during the process of fiber manufacturing.
Absorption
Absorption is caused by three different mechanisms:
1- Impurities in fiber material - occurs due to electronic transitions between the energy levels and because of charge transitions from one ion to another. A major source of attenuation is from transition of metal impurity ions such as iron, chromium, cobalt, and copper
2- Intrinsic absorption- Intrinsic absorption results from electronic absorption bands in UV region and from atomic vibration bands in the near infrared region. Absorption occurs when a photon interacts with an electronic in the valance band and excites it to a higher energy level
3- Atomic defects -imperfections in the atomic structure of the fiber materials such as missing molecules, high density clusters of atom group.
Absorption
Absorption inInfrared region
Absorption
Atomic DefectsExtrinsic
(Impurity atoms)Intrinsic
Absorption
Absorption inUltraviolet region
Scattering Loss
Small variation in material density, chemical composition, and structural inhomogeneity scatter light in other directions and absorb energy from guided optical wave.
Scattering losses in glass arise from microscopic variation in the material density from
1. Compositional fluctuations
2. Inhomogeneities or defects occurring during fiber manufacture
Rayleigh Scatter
Rayleigh scatter occurs at random when there are small changes in the refractive index of materials in which the light signal travels.
In this case, it is the changes in the refractive index of the core and the cladding of the fiber optic cable.
This loss is caused by the miniscule variation in the composition and density of the optical glass material itself, which is related to the fiber manufacturing process.
Rayleigh Scatter
Diagram-2: Light scattered during transmission
Bending Loss
Bending losses occurs in two forms - macrobending and microbending. When a cable is bent and it disrupts the path of the light signal. The tighter the bends of a cable, the greater it is of the light loss.
Bending Loss
Radiative losses occur whenever an optical fiber undergoes a bend of finite radius of curvature.
Macrobending: Light lost from the optical core due to macroscopic effects such as tight bends being induced in the fiber itself.Macrobending losses are normally produced by poor handling of fiber .Poor reeling and mishandling during installation can create severe bending of the fiber resulting in small but important localized losses
Microbending:Light lost from the optical core due to microscopic effects resulting from deformation and damage to the core cladding interface. Occurs when a fiber is sheathed within a protective cable. The stresses set up during the cabling process cause small axial distortions (microbends)
Microbending loss
Attenuation
Absorption in
Infrared region
Absorption
Atomic Defects
Extrinsic (Impurity atoms)
Intrinsic Absorption
Absorption in
Ultraviolet region
Attenuation
Scattering Losses
Compositional fluctuations in material
Inhomogeneities or defects
in fiber
Radiative losses/ Bending
losses
Macroscopic bends
Microscopic bends
Signal Distortion in FibersSignal Distortion in Fibers
Optical signal weakens from attenuation mechanisms and broadens due to distortion effects
Eventually these two factors will cause neighboring pulses to overlap.
After a certain amount of overlap occurs, the receiver can no longer distinguish the individual adjacent pulses and error arise when interpreting the received signal.
Dispersion
Dispersion is the spreading out of a light pulse as it travels through the fiber.
Attenuation only reduces the amplitude of the output waveform which does not alter the shape of the signal.
Dispersion distorts both pulse and analog modulation signals
Three types: Modal Dispersion Chromatic Dispersion Polarization Mode Dispersion (PMD)
Dispersion
Modal Dispersion
Modal Dispersion Spreading of a pulse because different modes (paths)
through the fiber take different times Only happens in multimode fiber Reduced, but not eliminated, with graded-index fiber
Chromatic Dispersion
Different wavelengths travel at different speeds through the fiber
This spreads a pulse in an effect named chromatic dispersion
Chromatic dispersion occurs in both single mode and multimode fiber Larger effect with LEDs than with lasers A far smaller effect than modal dispersion
Polarization Mode Dispersion
Light with different polarization can travel at different speeds, if the fiber is not perfectly symmetric at the atomic level
This could come from imperfect circular geometry or stress on the cable, and there is no easy way to correct it
It can affect both singlemode and multimode fiber
Modal Distribution
In graded-index fiber, the off-axis modes go a longer distance than the axial mode, but they travel faster, compensating for dispersion But because the off-axis modes travel further, they
suffer more attenuation
Insertion Losses
Most important performance indicator of a fiber optic interconnection. This is the loss of light signal, measured in decibels (dB), during the insertion of a fiber optic connector.
Some of the common causes of insertion losses includes:(i) the misalignment of ferrules during connection,(ii) the air gap between two mating ferrules, and(iii) absorption loss from impurities such as scratches and oil contamination
Insertion loss can be minimized by proper selection of interconnect materials, good polishing and termination process of fiber connectors
Types of insertion losses
Coupling Losses- The connector assembly must maintain
stringent alignment tolerances to ensure low mating losses.
- The losses should be around 2 to 5 percent (0.1 to 0.2 dB) and must not change significantly during operation and after numerous connects and disconnects.
Types of insertion losses
Splicing Losses- Optical power loss at the splicing point of two
ends of optical fiber is known as splice loss.- It is important to remember that actual
splice-loss is the measured splice-loss in both directions divided with two.
Types of insertion losses
Connector Loss - Optical loss at connection points in fiber
cables- Connector losses are associated with the
coupling of the output of one fiber with the input of another fiber, or couplings with detectors or other components.
LOSSES CALCULATION
• Total Loss = Lsplice + Lfiber + Lconn. + Lnon-linear
Lsplice = Splice Loss
Lfiber = Fiber Loss
Lconn. = Connector Loss
Lnon-linear= Non-linear Loss
Gain,G = Gainamp + Gnon-linear
Gainamp = Amplifier Gain
Gnon-linear = Non-linear Gain
Formula
COUTION !!! PRX in dBm or dBW PTX in dBm or dBW Total Losses in dB Total Gain in dB PMARGIN in dB
dB = 10 log (Po/Pin) = 10 log (PRX / PTX)
dBm = 10 log (P/1mW) P PRX atau PTX
dBm = 10 log (P/1mW) P PRX atau PTX