lighting control with wireless technologyripple current uout max. turn-on time dimming interface...

These PIR sensor heads are specially designed for highbay and lowbay lumianire designs. Offering IP64 and IP65 miniaturised designs, they allow the luminaire designer freedom of placement for high performance lighting controls withaesthetically pleasing results. They work with HC038V, HCD038 1-10V or DALI base units, or connect directly with ourHex-driveTM range of LED drivers. They are easily set-up and commissioned using the HA01 long-range IR sender unit whichis programmed via our smartphone App. The Bluetooth element of this system exists only between a smart device and the HA01programming device, the sensors are independant and are not capable offorming a wireless mesh network. For this system,please refer to our HC038V /BT and HCD038 /BT product options.

Lighting Control With Wireless Technology

HIR09x and HIR14x PIR Sensor Heads with HC038V / HCD038 & Hex-driveTM

Detachable Version for Highbay and Lowbay Luminaires

Applications

Free smartphone App forset-up and commissioning

HIR09/FIP64 PIR unit (fascia only) with daylight harvest photocell and flush mount fixing ring. Up to 12m

mounting height for highbay applications.

HIR09/CIP64 PIR unit (fascia only) with daylight harvest photocell. Features moulded threaded bolt for screw

fixing to the luminaire. Up to 12m mounting height for highbay applications.

HIR09/SIP64 surface mounting PIR unit (fascia only) with daylight harvest photocell. Up to 12m mounting

height for highbay applications.

HIR14 & HIR14/LIP65 PIR sensor heads with daylight harvest photocell. Flush mount fixing and

low profile design.

HIR14 designed or up to 12m highbay luminaire designs.

HIR14/L designed or up to 3m lowbay luminaire designs.

HA01

iOS

Compatible with

iOS 9.0 or later

Compatible with

Android 5.0 or later

Bluetooth enabled smart devices have a limited range, and devices to be comissioned in highbay installations are often beyondthe range of the smart device. By using the HA01, the commissioning engineer can set-up the sensor on the smartphone screen,and then send the settings using the long range Infra-red sensor. What’s more, the HA01 can read and acquire the settingsof the sensor for inspection or repeating to a new or replacement sensor on the same installation.

Technical Data For Sensor Heads

* The detection range is heavily influenced by antenna placement (angle of approch) and different walking paces. It may be reduced under certain conditions.

360O

5VDC

PIR detectionSensor principle

Operation voltage

Detection range *

Detection angle

HIR09 ( O x H) 16m x 12m

HIR14 ( O x H) 16m x 5m x 12m

HIR14/L ( O x H) 8m x 5m x 3m

PIR Sensor Properties

C. HIR09/CScrew to the luminaire by conduit

Daylight harvest

For highbay application

IP64

The cable length is around 30cm.

LensAccessories

RJ12 connector 25 33.9

M13

12

Ø40

.5

25

42.763

B. HIR09/FFlush mounting

Daylight harvest


IP64


Ø48

30.4

21.5

1.2

LensAccessories

RJ12 connector

32.6

23.2

20

Ø36.3

Lens Housing

RJ12 connector

Lug

PIR sensor heads

A. HIR09/SSurface mounting

Daylight harvest


IP64


D. HIR14PIR sensor head

Daylight harvest


IP65


Ø3.1

43.2

33

66

73

15.5 29

Lens

PCB

AccessoriesInstallation hole

RJ12 connector

Seal ring

E. HIR14/L

PIR sensor head

Daylight harvest

For lowbay application

IP65


Ø3.1

43.2

33

66

73

15.5 29

Lens

PCB

AccessoriesInstallation hole

RJ12 connector

Seal ring

Dimensions

HA01 PIR-bluetooth Converter

The HA01 is a comissioning tool which may be programmed using an Android or iOS smart device with the standard Hytronik APP. Settings are stored within the HA01 and then each sensor is programmed with a single button press:

- One Key Comissioning!

PIR

PIR

Detection Pattern

Using HA01 with HIR09x and HIR14x

Furthermore, the settings stored within a sensor may be ‘read-back’ to the APP for verification of correct setting or duplicating toa second smart device if the original is no longer available for programming further sensors that may be required on the installation. Simply point the HA01 device towards the sensior to be read and follow the on-screen in instructions on the APPto read back the settings.

Practically unlimited setting configurations can be created and named on the smart device. A single setting configuration may be uploaded to the HA01 for use at any time.

The HA01 contains a rechargeable lithium ion battery pack which is guaranteed for 1000 charges. The battery provides power for the communication circuitry, but also serves a useful USB charging port for the smart device.

For full instructions, please refer to the HA01 user manual and APP user guides.

Technical Data For HA01

Charger (USB MICRO B)

3.8V Li-ion 12AhBattery

USB Output (USB TYPE A)

I.R to Sensor Range

5V, 2A

15m (sending)

15m (receiving)

5V, 1A

*The detection patterns are based upon 5km/h movement speed.

HIR09

Tangent

ial move

ment 16m

Radial m

ovement

10m

12m

HIR14

12m

16m

5m

HIR14L

3m

8m

5m

4 wireless meshlighting control withDALI or 1-10V output

Technical Data For Control Base (HC038V / HCD038)

Stand-by power

220~240VAC 50/60Hz Mains voltage

Load ratings:

HC038V

HCD038

<0.5W

400W (capacitive)

30mA, 16VDC (max. 15 devices)

20sWarming-up

800W (resistive)

Input Characteristics

EMC standard (EMC)

Safety standard (LVD)

Certification

Radio Equipment (RED)

EN55015, EN61000, EN61547

Semko, CB, CE , EMC, RED, RCM

EN60669, AS/NZS60669

EN300440, EN301489 EN62479, EN300328

Safety and EMC (Common Data)

Tc: +80O

C

Operation temperature

Case temperature (Max.)

Ta: -20O

C ~ +55O

C

Environment

IP20 IP rating

HCD038 DALI Control Base

HC038V 1-10V Control Base

Features

Synchrony

30mA Broadcast DALI output for up to 15 LED drivers per node

Permanent settings memory, protected against loss of power

Switch-Dim with synchronization for simple manual over-ride

1-10V output control option

5 Year, 50,000hr warranty

Tri-level dimming control based upon occupancy (also known as corridor function)

Daylight harvest function to regulate light output for maintaining required lux level

A Bluetooth tranceiver node with 1-10V dimming output, the linear shapecontrol base HC038V can be built behind the PCB board. It is also perfect forapplications where space is restricted for cables and externally mountedlighting controls. Features manual switch input and port for a range of minatureantennas.

This device contains the same features of the HC038V above. Instead of 1-10Vdimming output, the HCD038 features DALI control with a 30mA power supplyfor up to 15 LED driver connections.

Using HIR09x and HIR14x with HC038V & HCD038

Control Base

1-10V-

RJ12 connector Push

L’

NL

N1-10V+

RJ12 connector

NL

DALI

Push

120

30

21

4.5

110.5

4.5

B. HCD038 (DALI output)

A. HC038V (1-10V output)

Dimensions and Terminals

Wire Preparation

DALI version

1-10V version

16 - 18 AWG

8mm

To make or release the wire from the terminal,

use a screwdriver to push down the button.

Wiring Diagram

HC038V

LED Driver

LED Driver

NL

1-10V+1-10V-

NL

1-10V+1-10V-1-10V+

1-10V

PL’NNL

-

LN

HCD038

DALI Driver

DALI Driver

DALIDALI

LN

DALIDALI

LN

DALIDALIPush

NL

LN

Technical Data for Hex-driveTM

The following data is given as an overview of the Hex-drive range for reference in accordance with the HIR09x and HIR14x

wireless technology products. For full data, please refer to our dedicated Hex-drive datasheets.

TM

TM

>0.93

Configurable Constant Current (CC) Output via Dip-Switch

Active PFC Design

ANALOGUE Analogue Flicker-free Dimming

Logarithmic Dimming with Multiple Dimming Inputs:

Thermal Cut-out Protection

Permanent Settings Memory, Protected against Loss of Power

5 Year, 50,000hr Warranty

All with Auto-restart}Over-load Protection

Short Circuit Protection

Intelligent Thermal Management

By simply connecting the sensor head via the RJ12 connector, the LED driver is automaticallyenabled for control via the 4 mesh network.

Once an antenna has been connected to the Hex-driveTM LED driver, all other control inputs(i.e. DALI & 1-10V) are disabled.

Using HIR09x and HIR14x with Hytronik Hex-DriveTM

Constant Current LED Drivers

Hytronik Hex-driveTM LED drivers feature a high level of specification which includes:

EN55015, EN61547, EN61000-3-2, EN61000-3-3

EN61347-1,EN62493,EN61347-2-13

IEC62386-101 ; IEC62386-102 ; IEC62386-207

Model No.

Ripple Current

Uout Max.

Turn-on Time

Dimming Interface

Operation Temp.

Case Temp. (Max.)

IP Rating

EMC Standard

Safety Standard

DALI Standard

Certifications

Safety

and EMC

Environment

Output

88%

Input Output : 3000VAC

< 0.25mA

220~240VAC 50/60Hz

HED1045

<3%

75V

< 0.5s

Ta: -20~+45

85

0.22~0.2A

0.95

Mains Voltage

Mains Current

Power Factor

Max. Efficiency

Dielectric Strength

Leakage Current

HED1050H

<3%

110V

< 0.5s

Ta: -20~+50

80

0.3~0.25A

0.95

HED1080H

<3%

120V

< 0.5s

Ta: -20~+50

80

<3%

70V

< 0.5s

Ta: -20~+50

85

0.45~0.4A

0.95

0.17~0.14A

0.9

HED1050L

<3%

200V

< 0.5s

Ta: -20~+50

80

0.3~0.25A

0.96Input

IP20

HED1025

<3%

90V

< 0.5s

Ta: -20~+50

80

0.15~0.13A

0.9

DALI, Switch-Dim

HEC7030/BF

DALI, Switch-DimDALI, 1-10V, Switch-Dim

Semko, CB, RCM, CE , EMC

Model: HED1025 1x25W

LN

Switch-Dim

DIP switch (for LED current selection)

RJ12 (sensor antenna)

LED+

LED -

DALIDALI

3

254.6

4.2

36

21.5

269

Model: HED1050H 1x50W high current

HED1050L 1x50W low current

HED1080H 1x80W high current

DALIRJ12 sensor antenna

1-10V +1-10V -

LED

390379.5

40.5

22

4.5


+LED -

DALI

Switch-Dim

Dimensions and Terminals

Model No.

HED102525.5W/ 425mA /12~60V 27W/ 450mA /12~60V 26W/ 475mA /12~55V 27.5W/ 500mA /12~55V

19.5W/ 325mA /12~60V 21W/ 350mA /12~60V 22.5W/ 375mA /12~60V 24W/ 400mA /12~60V

28W/ 500mA /12~56V 40W/ 700mA /12~56V 45W/ 900mA /12~50V 45W/ 1050mA /12~42V

40W/ 1200mA /12~34V 40W/ 1400mA /12~28V


49W/700mA /12~70V 50W/ 750mA /12~66V 50W/ 800mA /12~62V 50W/ 850mA /12~59V











30W/750mA /10~40V 23W/ 900mA /10~25V

50W/ 1100mA /12~45V 50W/ 1150mA /12~43V 50W/ 1200mA /12~42V

26W/ 525mA /12~50V 27.5W/ 550mA /12~50V 26W/ 575mA /12~45V 27W/ 600mA /12~45V


HED1045

HED1050H

HED1050L

HED1080H

HEC7030/BF

Max. output power/current/voltage range

Model: HED1045 1x45W

23

126

4.1

3.9

79.2

129.4140.6

additional cap for stand alone installation

185

DALISensor-Dim connection

1-10V+-

+- LED

LED current selection

Switch-DIMNL

Wire Preparation

0.5 - 1.5mm

8mm

To make or release the wire from the terminal,

use a screwdriver to push down the button.

Transceiver Node Connections (with optional Switch-Dim)

Sensor head

L

N

L

N

LED+

LED

RJ12

-

Switch-Dim

Model: HEC7030/BF 1x30W

22

.24

.14.1

10898.9

60

69


L

N

DALI2

DALI1

PUSH

RJ12

LED +

LED -

zero-crossing point

Alternating current

Designed into the software, the relay switches the

load right at the zero-crossing point, to ensure that

the in-rush current is minimised thus enabling the

maximum lifetime of the relay.

Zero-cross Relay Operation (HC038V)2

Lux Off Function4

The light turns of automatically when the surrounding natural light lux level exceeds the daylight threshold for more than 5min, even if

there is motion detected. If the stand-by period is set to infinity, the fixture will not switch off and will instead remain at the set stand-by

dimming level. Any motion detection is ignored until the natural light level decreases below the daylight threshold.

Hardware Features (Common to HC038V, HCD038 and Hex-driveTM

Daylight Harvest Function1

With built-in daylight sensor, the sensor can achieve daylight harvest function for energy saving purpose. Simply activate the daylight

harvest function in the App, and it will automatically adjust the light output according to the change of natural light.

Daytime

At night

The light turns on at full or dims to maintain the lux level. The light output regulates according to the level of natural

light available.

Light will not switch on when

natural light is sufficient.

The light automatically

switches on when natural

light is insufficient.

h

c

Light

natura

will not switch

al light is suffic

eon whe

cient.

li

t a

The

ligh

n ght turns on a

available.

t full or at dims to d maintain the ux levee l . The ligel ght output reg ral of naturulates ag ccordia ng to the leveln

The light is automatically

switched off after stand-by

time.

The light goes to stand-by

time after hold-time and stays

on dimming level preset.

12:00

cally

and-by y

ligh

tche

ht is automati

d off after sta

lly

atura

The ligh

switches

t automatica

s on when na

The

switnd-

and

-by

d stays al e ligh

time after hold-time

The

tim

t goes to stan

er hold-time a

Manual Override (‘Push’ Terminal)3

* Short Push (<1s): permanent on/off function; can also be configured to recall scene selection.

* Long Push (>1s): Brightness level adjustment.

Notes:

1) Both the adjustment on App and push switch can overwrite each other, the last adjustment remains in memory.

2) The switch functions are configured in the App.

3) The push terminal may be left unconnected if no manual control is required.

The ‘push’ terminal reserves the access of manual override function for the end-user to switch on/off, or adjust the light level by push-switch.

Furthermore, by using the binding option in the App, entire groups of fixtures may be wirelessly controlled by a single switch. Please refer to the

App user guide for further information.

lighting control with wireless technologyripple current uout max. turn-on time dimming interface...

Documents