light tape® design guide
DESCRIPTION
Light Tape employs a radically distinctive and patent-protected form of electroluminescent technology. It exists in the form of ultra-low-profile, lightweight panels and strips that seamlessly and evenly illuminate from edge to edge. The philosophy behind the product is simple: a light’s physical design should not restrict design or artistic vision. With Light Tape, you have the possibility to turn anything into the light. That’s where our specifics stop and your creativity starts.TRANSCRIPT
A3A2 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
Light Tape® The Unorthodox Alternative to a Conventional Routine.Stop using outdated sytems, take a leap...
©2015 Light Tape® Electro-LuminX Corporation www.lighttape.com
Even illumination: a uniform lightsource without di�usion , no hot-spots, at any size!
Custom shapes: allow your creativity todetermine your lights design.
No heat: Unlike LEDs, Light Tape® can run for40,000 hours and never gets hot. Ability to
withstand extreme tempatures.
Energy e�cient: Light Tape® uses 40% less power than traditional LEDs
Made in the USA: Built with pride, manufactured to last.
Thinner than a credit card: Light Tape® can fit into any tight area with ease.
Durability: Extremely impact resistant, heavy load capable. Light Tape® can withstand a bullet and still illuminate.
Easy Installation: Our technology is easyto install. Interior or Exterior, Light Tape®
illuminates 150 feet on a single connection.
Prepare to beilluminated
Light Tape is an electroluminescent or ‘EL’ lamp that challenges the way the world uses light. It’s thinner than a credit card and illuminates evenly, end to end, side to side. Shape it , curve it, choose your color. That’s where our specifics stop and your creativity starts.
As simple as a traditional lamp - plug it in and turn it on - but a complex evolution to the lighting industry. Light Tape® is based on electroluminescent, or "EL" technology; our one of a kind split-electrode technology and patent-protected polymer chemistry produce a material unlike any other.
A5A4 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
How Light Tape® Works
Enviroshield™Encapsulating Barrier
Color Filter w/UV Protection
Light Emitting Transparent Electrode
High Bright Phosphor
Dielectric Insulation
Rear Electrodes
PatentedPolymerChemistry
Compared to alternate EL technologies, no one comes close to our quality. We start by employing only the best materials to deliver shocking performance. We have a unique manufacturing process, a departure from traditional batch silk screening. Would you want your light madeon the same machine as a t-shirt screen printer? We don’t either, but that is how most alternate lamps are made.
Novel Chemistry: Light Tape®’s one-of-a-kind chemistry is protected by numerous patents. Our material’slayers are bonded at the chemical level, producing a brighter, more durable lighting source. Light Tape® is a true solid state system. Other EL producers glue the rear electrode to the material, which easily separates with flexing or temperature changes, leading to electrical failure. Best Materials: Only the best phosphors and conductive films are used in Light Tape®. The combination produces a brighter, more durable light that uses less energy. Other EL producers use low grade phosphors and poor conductive materials resulting in non-uniformity of brightness and poor energy efficiency, not to mention much shorter lifetimes. American Made: Light Tape® is manufactured in the United States under strict quality control standards. Ourown proprietary production methods create an electroluminescent light source unlike any other in the world.We are producing a lamp that is built to last, able to withstand the toughest applications. Unprecedented lifetimes: We are producing a lamp that is built to last, able to withstand the toughest applications.
There are dozens of things that cause a lamp to fail, but most do not affect Light Tape®.
Light Tape® Physical Specifications
Thickness (varies depending on color) 0.010 to 0.020 inches / 0.254 to 0.305 millimeters
Protective Encapsulation Seal ” on each side (+/-1/16” of an inch, +/- 0.159 cm)
Light Tape® Illuminated Width 0.25 to 33 inches / 0.625 to 90 cm
Illumination Coverage Infinite, can be tiled without a break in light
Power System
Light Tape® Load Capacitive Load
Phase Angle 78° Leading Edge
Light Tape® Power Consumption by Area 0.016 watts per in2 / 0.106 watts per cm2
Light Tape® Amperage Consumption by Area** 0.19 milliamps per in2 / 1.23 milliamps per cm2
Light Tape® Watts per Linear Meter at 2.54 cm wide 0.4 to 1.1 watts based on low to full brightness dimming
Light Tape® Watts per Square Meter 0.21 to 0.53 watts based on low to full brightness dimming
Light Tape® Output Voltage (dimmable) 250 Volts AC, +/- 50 Volts AC
Light Tape® Operating Frequency 800 Hertz, +/- 300 Hertz (depending on tuning)
AC Driver Input Voltage Range 90 to 260 Volts AC
DC Driver Input Voltage Range 3 to 24 Volts DC (12 Volts DC standard)
Power Source ELLC Smart Driver™ Power Supplies
Controllable Dimming, 0 to 10 Volts DC and DMX 512 Capable
Light Tape® Performance
Useful Life - Hours 20,000 hours to excess of 40,000 hours
Useful Life - Years up to 20 years (dependent on drive parameters)
Average Brightness 125 cd/m2
Brightness Range 0 to 200 cd/m2
Brightness Differential - Completely Uniform +/- 1 cd/m2, independent of total surface area
Operating Temperature - Ambient -40°C to +65°C
Heat Gain During Operation Does not produce heat during operation
Compressive Strength - Ground Pressure 500 psi or more depending on mounting system
Impact Strength - Izod (73F) 6.5 ft-lbs/in2
Flexural Strength 700 >15,000 cycles ASTM D2176
Flexibility - Wrap Angle Contours around 6 millimeter diameter object
Punctureable Yes, will illuminate after puncturing
Maximum Processing Temperature 350°F / 177°C (depending on residence time)
Health and Safety
Safety Features Overload and short circuit protection. UL listed.
UL Certifications File number E319670, 2006/95/EC
CE Certification EC-Attestation of conformity – No.0704 63147 001
Low Voltage Directive Compliant
Environmental Compliance ROHS and WEES Directive
EMC Emissions Compliant EN55015 (CISPR15) Radiated and Conducted Emission
Flame Resistance UL 94VTM-0
International Protection Marking IP67, EN60529
**Data recorded at average brightness, with AC input power of 250 Volts and 850 Hertz.
©2015 Light Tape® Electro-LuminX Corporation www.lighttape.com
Light Tape® Specifications
B3B2 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
Light Tape® is a flat capacitor emitting light only on one surface. Versus other single point light sources like LED who emit light in sphere. When comparing surface brightness of an accent light, there is nothing more efficient.
LUM
ENS P
ER W
ATT
150
120
90
60
30
010-17 12-22 25-60 30-110 40-70 40-100 50-140 70-115 116-160
energy consumption
ILLUMINATED WIDTH
LENGTH
ILLUMINATION SOURCE
CURRENT - AMPS
TOTAL WATTS
ILLUMINATION COVERAGE
2.54 cm
1 linear meter
100% phospors
0.01
1
100% even
0.8 cm
1 linear meter
30 LEDs
3
7.2
2 cm gaps
1.27 cm
1 linear meter
100% phosphors
0.005
0.5
100% even
0.8 cm
1 linear meter
60 LEDs
6
14.4
1 cm gaps
100% backlit
square meter
100% phosphors
0.5
44
100% even
edge lit
square meter
240 LEDs
24
57.6
30% dimmer in center
Light Tape is off the
charts
BRIGHTNESS
HIGH
AVERAGE
LOW
watts/sqin
0.028
0.016
0.011
milamps/sqin
0.342
0.191
0.133
watts/sqcm
0.0043
0.0025
0.0017
milamp/sqcm
0.0530
0.0296
0.020
Light Tape® has a very linear power consumption. With every increase in area there is an equal increase in energy required to illuminate. The table can be utilized to estimate total wattage and current consumption.
LIGHT TAPE VS. LED IN ACCENT AND BACKLIGHTING APPLICATIONS
LIGHT TAPE POWER CONSUMPTION BY AREA
*Light Tape® data based on full brightness, consumption results can be much lower when dimming.
Light Tape® lamps’ energy consumption is unmatched; the ideal balance of brightness and even illumination. LIGHT TAPE LEDS
OFF ON
Natural Blue
Blue Green
Media White Electric BlueYellow
PinkPurple Orange Green
KryptoniteCaribbean Blue Rich Red International Red
OFF ON
OFF ON OFF ONOFF ON
OFF ONOFF ON OFF ON OFF ON
OFF ONOFF ON OFF ON OFF ON
CLASSIC SERIES
EXTREME SERIES
The colors in this table are simulated and the final product may vary. If an exact color is required, we recommend seeing a physical sample. Custom colors and widths are available, but may be subject to minimum order quantities, set-up fees, and approval testing.
Our base colors are Classic Natural Blue and Extreme Blue-Green. These colors appear white when off and colored when illuminated. We then all a filter to produce specific color options. All other colors will remain that color when not illuminated.
Light Tape® Color Options
Please refer to our Color Tech section for specific color data and measurements.
C3C2 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
ITEM NUMBER ILLUMINATED WIDTH LAMINATED WIDTH
TOP VIEW
.020
” .010”
SPLIT ELECTRODE
0.25” Clear Barrier
Encapsulation
extended connectiontabs; 2” standard length
Light Tape® Lamp LaminationExtension TabsConnectorScribe Line*
light tape® panel specifications
WHEN ORDERING, PLEASE SPECIFY
• Installation location - Interior (INT) or Exterior (EXT) • Desired illuminated color• Illuminated width – standard part number above, custom widths possible. Can be tiled & joined together with ease to illuminate a large area without seams or gaps• How long for each Light Tape lamp?• Power input location (please specify short or long side of lamp)• Extended connection tab lengths may be specified to help navigate wiring so connector can be hidden. The standard length is 2 inches from end of panel to beginning of connector. • Total number of lamps required.• A basic top or front view drawing is helpful to our engineering team. We can then suggest best electrical configuration for your project.
*the split electrode line is a critical element of Light Tape’s engineering that runs centered through the entire length.
P-lt-600
p-lt-1200
p-lt-1800
p-lt-2400
6” (15.24cm)
12” (30.48cm)
18”(45.72cm)
24”(60.96cm)
6.5” (16.51cm)
12.5”(31.75cm)
18.5”(46.99cm)
24.5”(62.23cm)
FEET OF LT LENGTH
up to 150
up to100
*custom widths available
ITEM NUMBER ILLUMINATED WIDTH LAMINATED WIDTH FEET OF LT LENGTH
TOP VIEW
.020
” .010”
SPLIT ELECTRODE
0.25” Clear Barrier Encapsulation
Light Tape® Lamp LaminationExtension TabsConnectorScribe Line*
light tape® strip specifications
WHEN ORDERING, PLEASE SPECIFY
• Installation location - Interior (INT) or Exterior (EXT) • Desired illuminated color• Illuminated width – standard part number above, custom widths possible.• What length for each Light Tape lamp?• Total number of lamps required.• Number of Smart Drivers™ required? Refer to the ‘Accent Lighting Sample Wiring Diagram’• Power Input - AC or DC and what input voltage?• A basic top or front view drawing is helpful to our engineering team. We can then suggest best electrical configuration for your project.
*the split electrode line is a critical element of Light Tape’s engineering that runs centered through the entire length.
lt-025
lt-050
lt-100
lt-150
lt-200
lt-300
lt-400
lt-600
0.25” (6.35mm)
0.5” (12.7mm)
1” (25.4mm)
1.5” (38mm)
2” (50.8mm)
3” (76.2mm)
4.0” (101.6mm)
6.0” (152.4mm)
0.75” (19.05mm)
1.0” (25.4mm)
1.5” (38.1mm)
2.0” (50.7mm)
2.5” (63.5mm)
3.5” (88.9mm)
4.5” (114.3mm)
6.5” (16.51cm)
up to 150
up to100
D1C4 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
How it works
ITEM NUMBER ILLUMINATED WIDTH CHANNEL WIDTH
P-lt-025
p-lt-050
p-lt-100
p-lt-200
0.25” (6.35mm)
0.5” (12.7mm)
1”(25.4mm)
2”(50.8mm)
0.92” (23.37mm)
1.17”(29.72mm)
1.67”(42.42mm)
2.67”(67.82mm)
1.17”(29.97mm)
1.42”(36.07mm)
1.92”(48.90mm)
2.92”(74.30mm)
CLIP WIDTH
light tape® snap n’ light specifications
6.35 Lamp A = 23.3712.7 Lamp A = 29.7225.4 Lamp A = 42.4250.8 Lamp A = 67.82
“A”
4.571.52 TYP
[Unit : mm]
MOUNTING CHANNEL
6.35 Lamp A = 29.9712.7 Lamp A = 36.0725.4 Lamp A = 48.9050.8 Lamp A = 74.30
“A”
15.67
2.29 TYP
[Unit : mm]
MOUNTING CLIP
14.3
Mounting Clips
ExtrusionLight Tape™
Connector Tabs
Connector
Screws
*Mount Clip is attached to mounting surface Mounting Channel holds the Light Tape® and snaps into the pre-attached mounting clips
MATERIAL Clear UV Stable Polycarbonate Mounting Channel
MOUNTING SCREW NO. 10
CLIP PLACEMENT One clip per 1 to 3 feet, depending on surface
UV SCREEN Yes, and non-yellowing
ROLL FORMAT 100 foot coils - or longer per special order
FEET OF LT LENGTH
up to 150
up to100
D3D2 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
how to request a quote?
Contact Information:
Application Type
Indicate location:
Indicate input power source:
Indicate the number of zones:
Specificed width(s) (custom widths and shapes are available):
Specified quantity and length(s):
Indicate color preference(s):
Provide a top view drawing of your lighting layout indicating dimensions of the Light Tape® and power source locations:
Indicate mounting preferences:
For adhesive tape or Velcro, indicate if you would like either to be pre-installed prior to arrival for an addional fee:
Connector preference
Descripe the purpose of the project and other things we should consider:
Please provide the answers to the questions below to expedite the process of preparing a quote. MULTI-POWER SUPPLY INSTALLATIONA top view example of a Light Tape® interior accent lighting installation. Note there are three segments of Light Tape® powered by three individual power supplies. Each power supply is selected based on the total surface area.
top view accent lighting example
SINGLE POWER SUPPLY INSTALLATIONNow a top view of the same Light Tape® installation as above. Note there are three segments of Light Tape® powered by one individual power supplly. The power supply is selected based on the total surface area of the all the segments combined. Each Light Tape® segment is connected via junction box to the same power supply.
82’ length 1” wide Natural Blue
65’ length1” wide
Kryptonite
PS PS
PS
SD 1000
LT-1
LT-2
80’ length2” wideGreen
LT-3
SD 1000
SD 2000
Surface AreaLT-1 = 780 sq2
LT-2 = 984 sq2
LT-3 = 1,920 sq2
3,684 total sq2
C
KeyPS = Power SupplyJB = Junction BoxC = Connection
C
C
SD 4000
wire back to central location
82’ length 1” wide
65’ length1” wide
LT-1
LT-2
80’ length2” wide
LT-3
Surface AreaLT-1 = 780 sq2
LT-2 = 984 sq2
LT-3 = 1,920 sq2
3,684 total sq2
PS JB
C
C
C
KeyPS = Power SupplyJB = Junction BoxC = Connection
Name; Company; Email; Phone; City, Country
Architectural, Brand, Out-of-Home, Safety, Creative/Other
Interior or Exterior
110 Volt AC, 220 Volt AC, 12 Volt DC, Other
(i.e 3 strips, 2 zones)
Refer to C2 and C3, Strips and Panel Specifications, pages
Please note that every lamp has a connector on one end. The total length of the lamp including strain relief will be approximately 5 inches longer than the lit length.
Refer to page B2 for available colors
Refer to the following pages for different solutions.
Double-sided adhesive, Velcro, extrusion channels, Other
Standard, Standard with extended tabs, Low Profile, or Low Profile with extended tabs
(a description of the design concept and photos of the space or of creative inspiration)
D5D4 Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation Copyright 2015 Light Tape® Electro-LuminX Lighting Corporation
top view layout: backlighting materials
BASIC BAR OR COUNTER TOPAny surface area can be evenly illuminated with a minimal number of panels and connections. A bar design resembling the one below would require only two Light Tape panels and one power supply. The Light Tape® panel is placed directly on surface with double sided adhesive.
COUNTER TOP WITH CUT OUTSLight Tape® panels can be custom cut to any shape and placed side-by-side or overlapping to seamlessly illuminate any surface. For custom shapes, a AI file will be needed.
24” Panel
6’ length
LT-1
LT-2
24” Panel
4’ length
2 - LT Panels: (24”x 6’) + (24“x4‘)=2,880 in2
2 - LT Connections w/ extension tabs1 - SD 4000
C
C
1 2
C C
KeyPS = Power SupplyJB = Junction BoxC = Connection JBPS
*Extension tabs make a seamless illumination possible. See Light Tape Panel Specification sheet for more information.
TOP VIEW
CROSS SECTION
3’
12’
LT-1LT-3
LT-4
KeyPS = Power SupplyJB = Junction BoxC = Connection
C
C C
CLT-2 LT-5
4 - LT Panels: (18”x 5’) = 4,320 in2
1- LT Custom Panel (24”x 3’) - (1’x2’ cutout) = 576 in2
5 - LT Connections w/ extension tabs1 - SD 8000 (total 4,896 in2 )
5’ 5’2’
C
*extended tabs
backlighting translucent materialsSYMMETRICAL SHAPESIlluminating a symmetrical shape is quite simple. When designing the shape, make sure the split electrode line is centered to allow for equal distribution of electricity.
C*extended tabs
KeyC = Connection
C
ASYMMETRICAL SHAPESIlluminating asymmetrical shapes is possible, but the placement of the scribe line needs to be considered before a design is submitted. There must be equal surface area on either side of the scribe line in order for the Light Tape to illuminate properly and evenly. We require an AI file be submitted then we can consult with the diesng from there. quite simple. When designing the shape, make sure the split electrode line is centered to allow for equal distribution of electricity.