lid support access ducting with inset lids -...
TRANSCRIPT
Charcon Specialist Products,Marions Way, Coventry Road,
Croft, Leicester LE9 3GP
Tel: 01455 288275/6Fax: 01455 285284
Email: [email protected]
An AGGREGATE INDUSTRIES PLC business
January 2005
CI /SfBYf2(90.6)
Uniclass
Access Ducting with Inset Lids
Charcon Specialist Products
STRENGTH IN INNOVATION
Stop end units
Lifting method
Access Ducting
Stop EndReference
SP 350 X 300
SP 600 X 300
80
80
500
500
609
854
70
90
Stop End Dimensions
(mm)
A D E
StopEnd
Weight(kg)
Installation ProcedureThe recommended installation procedure is as follows:-1. Prepare bed or foundation to suit ground conditions and loading.2. Position trough to line and level.3. Abut the next trough, the flat end face against the installed end face.
Bed and level the unit to suit.4. Haunch or back fill as required.5. Repeat the procedure to form the required duct length.6. Install the service within the duct.7. Position the lids in each duct unit, ensuring that there is exactly
two No. per duct.8. The units should be satisfactorily sealed using proprietary sealants
which are available from the Charcon Sales Office. Telephone 01455 288275.
Note: Lifting bar and shackle devices are also available from the Charcon Sales Office.
1. Insert lifting pinsthrough all four lifting
holes from the insidewall of the trough unit.
2. Attach locking nut and hand tighten.
3. Attach lifting hooksthrough the pin eye
at all four points.
4. Ensure lifting chains/steel ropes are symmetrical,
then begin lift.
5. Lift and place trough into position.
6. Remove shackles/hooksthen lifting device by
unscrewing the locking nut.
5
These precast units are a cost-effective,quick and easy method of constructingstop ends on site.
Transition units
Angle IronLid Support
Access Ducting90o degree units
Tee units
Introduction
Charcon Specialist Products is a leading supplierof Service Protection products to the constructionand service industry.
Charcon Specialist Products, part of AggregateIndustries UK Ltd, offers extensive technicalexpertise and manufacturing capability to provide the best foundation for all your ServiceProtection needs.
Contents
Features and benefits Page 3Access ducting Page 3Trafficking application classes Page 390o degree units Page 4Tee units Page 4Stop end units Page 5Transition units Page 5Installation procedure Page 5
Quality Assurance
The Quality Management Systems and Procedures of Aggregate Industries havebeen approved by Lloyd’s Register QualityAssurance Ltd to BS EN ISO 9001:2000.
Other Charcon Products
Service Protection RangeRailway Platform ProductsBespoke ItemsPrecast Concrete BollardsFilter Bed Wall and Tile SystemsFunctional Kerbs Natural Stone Products Eco Range of Paving and KerbsBritish/European Standard Flag and Kerb Products Surface Water Drainage Products Hard Landscaping Range of Flag and Block Paving and KerbsLightweight KerbsSustainable Drainage Systems
For further details please contact:
Sales Office
Charcon Specialist Products, Marions Way,Coventry Road, Croft, Leicester LE9 3GP
Tel: 01455 288275/6 Fax: 01455 285284Email: [email protected]
AGGREGATE INDUSTRIES UK LTD
Registered Office: Bardon Hill, Coalville
Leicestershire, LE67 1TL,
Registered in England No. 498629
An AGGREGATE INDUSTRIES PLC business
While every effort is made to ensure the accuracy of content, both written and pictorial, interested parties
should contact AGGREGATE INDUSTRIES UK LTD (the company) for verification. This brochure and any advice
is provided by the Company free of charge and is accordingly on terms that no liability of any kind (including
liability for negligence) will attach to the Company or its servants or agents arising out of, or in connection
with, or in relation to this brochure or any such advice.
Any goods supplied by the company will be supplied solely upon its standard conditions of sale, copies of
which are available on request.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1071
1071
1071
1071
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
580
580
660
660
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1000
1000
1500
1500
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
530
530
750
750
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
4
SP 600 only
SP 350 only
SP 350 only
SP 600 only
Angle Iron Lid Support
Angle Iron Lid Support
2
Standard precast concrete access ducting with inset lids
Features and Benefits
• Mechanical protection• A number of wheel load lid options • Structurally reinforced• Positively marked and identified• Reduced installation time• Lifting holes in troughs and lids• Simple installation• Secure units• Trafficking capability• Easy access to services• Assured performance• Bespoke items
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP(Pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Trafficking Application ClassesCharcon Specialist Products offers arange of lids to suit all your traffickingapplication needs. Each lid has the necessary lifting inserts to facilitate lifting when accessing the ducts at afuture date.
Trafficking Application Classes are as follows:
Light DutyFor use in private driveways and grassedareas e.g. parkland maintained with mowing equipment. Maximum wheelloading of two tonnes.
Medium DutyFor use in car parks and access roads subject to occasional commercial vehicletraffic e.g access to works and plants.Maximum wheel loading of five tonnes.
Heavy DutySteel lidded units offer a maximumwheel load of 11.5 tonnes which can be used for lorry parks and kerbsides(non - public highways) e.g. all road-goingvehicles up to 15 mph max.
It is strongly advised that you select ahigher grade of unit if channelised trafficking or an excessive amount ofcommercial traffic is anticipated.
Loading test data and trafficking application classes are based on linear drainage standard DIN 19580which forms the basis of a draftEuropean Standard.
Units have been subjected to test loads from 15kN (pedestrian) up to 400kN(heavy duty). This test data, togetherwith our unrivalled experience of AccessDucting in trafficked situations, hasenabled us to help our clients to select the best product for their application.
All lifting devices for the troughs and lidsare available from the Charcon SalesOffice.
Access Ducting - Detailed Design Information
TroughReference
1000
1000
1000
1000
1000
1000
1000
1000
340
340
585
585
380
570
960
1000
296
296
296
296
400
600
1000
510
500
500
500
500
654
854
1304
814
609
609
854
854
700
900
1426
1426
365
365
610
610
410
610
1036
1036
372
372
425
425
570
787
1565
1055
SP 350**
SP 350**
SP 600**
SP 600**
SP 400**
SP 600**
SP 1000**
SP 1000**
500
500
500
500
500
500
500
500
467
467
712
712
512
712
1242
1242
100
100
100
100
100
100
150
150
56
60
85
90
62
90
225
225
2 tonnes
5 tonnes
2 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
Deha
Deha
Deha
Deha
LidLifterType
Max TrafficWheel Load
(tonnes)
3 SP 350 X 300 LD *
SP 350 X 300 MD *
SP 600 X 300 LD *
SP 600 X 300 MD *
SP 400 X 400 MD *
SP 600 X 600 MD *
SP 1000 X 1000 MD *
SP 1000 X 510 MD *
Main photo with Precast Concrete Lid. Top right with Steel Lid. Bottom right with GRP Cover.
Access Ducting90o degree units
Tee units
Introduction
Charcon Specialist Products is a leading supplierof Service Protection products to the constructionand service industry.
Charcon Specialist Products, part of AggregateIndustries UK Ltd, offers extensive technicalexpertise and manufacturing capability to provide the best foundation for all your ServiceProtection needs.
Contents
Features and benefits Page 3Access ducting Page 3Trafficking application classes Page 390o degree units Page 4Tee units Page 4Stop end units Page 5Transition units Page 5Installation procedure Page 5
Quality Assurance
The Quality Management Systems and Procedures of Aggregate Industries havebeen approved by Lloyd’s Register QualityAssurance Ltd to BS EN ISO 9001:2000.
Other Charcon Products
Service Protection RangeRailway Platform ProductsBespoke ItemsPrecast Concrete BollardsFilter Bed Wall and Tile SystemsFunctional Kerbs Natural Stone Products Eco Range of Paving and KerbsBritish/European Standard Flag and Kerb Products Surface Water Drainage Products Hard Landscaping Range of Flag and Block Paving and KerbsLightweight KerbsSustainable Drainage Systems
For further details please contact:
Sales Office
Charcon Specialist Products, Marions Way,Coventry Road, Croft, Leicester LE9 3GP
Tel: 01455 288275/6 Fax: 01455 285284Email: [email protected]
AGGREGATE INDUSTRIES UK LTD
Registered Office: Bardon Hill, Coalville
Leicestershire, LE67 1TL,
Registered in England No. 498629
An AGGREGATE INDUSTRIES PLC business
While every effort is made to ensure the accuracy of content, both written and pictorial, interested parties
should contact AGGREGATE INDUSTRIES UK LTD (the company) for verification. This brochure and any advice
is provided by the Company free of charge and is accordingly on terms that no liability of any kind (including
liability for negligence) will attach to the Company or its servants or agents arising out of, or in connection
with, or in relation to this brochure or any such advice.
Any goods supplied by the company will be supplied solely upon its standard conditions of sale, copies of
which are available on request.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1071
1071
1071
1071
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
580
580
660
660
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1000
1000
1500
1500
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
530
530
750
750
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
4
SP 600 only
SP 350 only
SP 350 only
SP 600 only
Angle Iron Lid Support
Angle Iron Lid Support
2
Standard precast concrete access ducting with inset lids
Features and Benefits
• Mechanical protection• A number of wheel load lid options • Structurally reinforced• Positively marked and identified• Reduced installation time• Lifting holes in troughs and lids• Simple installation• Secure units• Trafficking capability• Easy access to services• Assured performance• Bespoke items
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP(Pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Trafficking Application ClassesCharcon Specialist Products offers arange of lids to suit all your traffickingapplication needs. Each lid has the necessary lifting inserts to facilitate lifting when accessing the ducts at afuture date.
Trafficking Application Classes are as follows:
Light DutyFor use in private driveways and grassedareas e.g. parkland maintained with mowing equipment. Maximum wheelloading of two tonnes.
Medium DutyFor use in car parks and access roads subject to occasional commercial vehicletraffic e.g access to works and plants.Maximum wheel loading of five tonnes.
Heavy DutySteel lidded units offer a maximumwheel load of 11.5 tonnes which can be used for lorry parks and kerbsides(non - public highways) e.g. all road-goingvehicles up to 15 mph max.
It is strongly advised that you select ahigher grade of unit if channelised trafficking or an excessive amount ofcommercial traffic is anticipated.
Loading test data and trafficking application classes are based on linear drainage standard DIN 19580which forms the basis of a draftEuropean Standard.
Units have been subjected to test loads from 15kN (pedestrian) up to 400kN(heavy duty). This test data, togetherwith our unrivalled experience of AccessDucting in trafficked situations, hasenabled us to help our clients to select the best product for their application.
All lifting devices for the troughs and lidsare available from the Charcon SalesOffice.
Access Ducting - Detailed Design Information
TroughReference
1000
1000
1000
1000
1000
1000
1000
1000
340
340
585
585
380
570
960
1000
296
296
296
296
400
600
1000
510
500
500
500
500
654
854
1304
814
609
609
854
854
700
900
1426
1426
365
365
610
610
410
610
1036
1036
372
372
425
425
570
787
1565
1055
SP 350**
SP 350**
SP 600**
SP 600**
SP 400**
SP 600**
SP 1000**
SP 1000**
500
500
500
500
500
500
500
500
467
467
712
712
512
712
1242
1242
100
100
100
100
100
100
150
150
56
60
85
90
62
90
225
225
2 tonnes
5 tonnes
2 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
Deha
Deha
Deha
Deha
LidLifterType
Max TrafficWheel Load
(tonnes)
3 SP 350 X 300 LD *
SP 350 X 300 MD *
SP 600 X 300 LD *
SP 600 X 300 MD *
SP 400 X 400 MD *
SP 600 X 600 MD *
SP 1000 X 1000 MD *
SP 1000 X 510 MD *
Main photo with Precast Concrete Lid. Top right with Steel Lid. Bottom right with GRP Cover.
Access Ducting90o degree units
Tee units
Introduction
Charcon Specialist Products is a leading supplierof Service Protection products to the constructionand service industry.
Charcon Specialist Products, part of AggregateIndustries UK Ltd, offers extensive technicalexpertise and manufacturing capability to provide the best foundation for all your ServiceProtection needs.
Contents
Features and benefits Page 3Access ducting Page 3Trafficking application classes Page 390o degree units Page 4Tee units Page 4Stop end units Page 5Transition units Page 5Installation procedure Page 5
Quality Assurance
The Quality Management Systems and Procedures of Aggregate Industries havebeen approved by Lloyd’s Register QualityAssurance Ltd to BS EN ISO 9001:2000.
Other Charcon Products
Service Protection RangeRailway Platform ProductsBespoke ItemsPrecast Concrete BollardsFilter Bed Wall and Tile SystemsFunctional Kerbs Natural Stone Products Eco Range of Paving and KerbsBritish/European Standard Flag and Kerb Products Surface Water Drainage Products Hard Landscaping Range of Flag and Block Paving and KerbsLightweight KerbsSustainable Drainage Systems
For further details please contact:
Sales Office
Charcon Specialist Products, Marions Way,Coventry Road, Croft, Leicester LE9 3GP
Tel: 01455 288275/6 Fax: 01455 285284Email: [email protected]
AGGREGATE INDUSTRIES UK LTD
Registered Office: Bardon Hill, Coalville
Leicestershire, LE67 1TL,
Registered in England No. 498629
An AGGREGATE INDUSTRIES PLC business
While every effort is made to ensure the accuracy of content, both written and pictorial, interested parties
should contact AGGREGATE INDUSTRIES UK LTD (the company) for verification. This brochure and any advice
is provided by the Company free of charge and is accordingly on terms that no liability of any kind (including
liability for negligence) will attach to the Company or its servants or agents arising out of, or in connection
with, or in relation to this brochure or any such advice.
Any goods supplied by the company will be supplied solely upon its standard conditions of sale, copies of
which are available on request.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP (pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1071
1071
1071
1071
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
580
580
660
660
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
Access Ducting - Detailed Design Information
TroughReference
SP 350 X 300 *
SP 350 X 300 *
SP 600 X 300 *
SP 600 X 300 *
1000
1000
1500
1500
340
340
585
585
445
445
445
445
500
500
500
500
609
609
854
854
365
365
610
610
530
530
750
750
SP 350**
SP 350**
SP 600**
SP 600**
500
500
500
500
467
467
712
712
100
100
100
100
56
60
85
90
2 tonnes
5 tonnes
2 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F
1054
1054
1299
1299
G H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
LidLifterType
Max TrafficWheel Load
(tonnes)
4
SP 600 only
SP 350 only
SP 350 only
SP 600 only
Angle Iron Lid Support
Angle Iron Lid Support
2
Standard precast concrete access ducting with inset lids
Features and Benefits
• Mechanical protection• A number of wheel load lid options • Structurally reinforced• Positively marked and identified• Reduced installation time• Lifting holes in troughs and lids• Simple installation• Secure units• Trafficking capability• Easy access to services• Assured performance• Bespoke items
* Also available with reduced rebate to takeGRP lids with a side wall hole for the entry /exit of services.
** These lid sizes are available in GRP(Pedestrian), galvanised steel (11.5T), and steellids suitable for infill with paving or concrete.
Trafficking Application ClassesCharcon Specialist Products offers arange of lids to suit all your traffickingapplication needs. Each lid has the necessary lifting inserts to facilitate lifting when accessing the ducts at afuture date.
Trafficking Application Classes are as follows:
Light DutyFor use in private driveways and grassedareas e.g. parkland maintained with mowing equipment. Maximum wheelloading of two tonnes.
Medium DutyFor use in car parks and access roads subject to occasional commercial vehicletraffic e.g access to works and plants.Maximum wheel loading of five tonnes.
Heavy DutySteel lidded units offer a maximumwheel load of 11.5 tonnes which can be used for lorry parks and kerbsides(non - public highways) e.g. all road-goingvehicles up to 15 mph max.
It is strongly advised that you select ahigher grade of unit if channelised trafficking or an excessive amount ofcommercial traffic is anticipated.
Loading test data and trafficking application classes are based on linear drainage standard DIN 19580which forms the basis of a draftEuropean Standard.
Units have been subjected to test loads from 15kN (pedestrian) up to 400kN(heavy duty). This test data, togetherwith our unrivalled experience of AccessDucting in trafficked situations, hasenabled us to help our clients to select the best product for their application.
All lifting devices for the troughs and lidsare available from the Charcon SalesOffice.
Access Ducting - Detailed Design Information
TroughReference
1000
1000
1000
1000
1000
1000
1000
1000
340
340
585
585
380
570
960
1000
296
296
296
296
400
600
1000
510
500
500
500
500
654
854
1304
814
609
609
854
854
700
900
1426
1426
365
365
610
610
410
610
1036
1036
372
372
425
425
570
787
1565
1055
SP 350**
SP 350**
SP 600**
SP 600**
SP 400**
SP 600**
SP 1000**
SP 1000**
500
500
500
500
500
500
500
500
467
467
712
712
512
712
1242
1242
100
100
100
100
100
100
150
150
56
60
85
90
62
90
225
225
2 tonnes
5 tonnes
2 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
5 tonnes
Trough Dimensions(mm)
A B C D E F H I J
TroughWeight
(kg)
LidRef
LidDimensions
(mm)
LidWeight
(kg)
Key
Key
Key
Key
Deha
Deha
Deha
Deha
LidLifterType
Max TrafficWheel Load
(tonnes)
3 SP 350 X 300 LD *
SP 350 X 300 MD *
SP 600 X 300 LD *
SP 600 X 300 MD *
SP 400 X 400 MD *
SP 600 X 600 MD *
SP 1000 X 1000 MD *
SP 1000 X 510 MD *
Main photo with Precast Concrete Lid. Top right with Steel Lid. Bottom right with GRP Cover.
Charcon Specialist Products,Marions Way, Coventry Road,
Croft, Leicester LE9 3GP
Tel: 01455 288275/6Fax: 01455 285284
Email: [email protected]
An AGGREGATE INDUSTRIES PLC business
January 2005
CI /SfBYf2(90.6)
Uniclass
Access Ducting with Inset Lids
Charcon Specialist Products
STRENGTH IN INNOVATION
Stop end units
Lifting method
Access Ducting
Stop EndReference
SP 350 X 300
SP 600 X 300
80
80
500
500
609
854
70
90
Stop End Dimensions
(mm)
A D E
StopEnd
Weight(kg)
Installation ProcedureThe recommended installation procedure is as follows:-1. Prepare bed or foundation to suit ground conditions and loading.2. Position trough to line and level.3. Abut the next trough, the flat end face against the installed end face.
Bed and level the unit to suit.4. Haunch or back fill as required.5. Repeat the procedure to form the required duct length.6. Install the service within the duct.7. Position the lids in each duct unit, ensuring that there is exactly
two No. per duct.8. The units should be satisfactorily sealed using proprietary sealants
which are available from the Charcon Sales Office. Telephone 01455 288275.
Note: Lifting bar and shackle devices are also available from the Charcon Sales Office.
1. Insert lifting pinsthrough all four lifting
holes from the insidewall of the trough unit.
2. Attach locking nut and hand tighten.
3. Attach lifting hooksthrough the pin eye
at all four points.
4. Ensure lifting chains/steel ropes are symmetrical,
then begin lift.
5. Lift and place trough into position.
6. Remove shackles/hooksthen lifting device by
unscrewing the locking nut.
5
These precast units are a cost-effective,quick and easy method of constructingstop ends on site.
Transition units
Angle IronLid Support
Charcon Specialist Products,Marions Way, Coventry Road,
Croft, Leicester LE9 3GP
Tel: 01455 288275/6Fax: 01455 285284
Email: [email protected]
An AGGREGATE INDUSTRIES PLC business
January 2005
CI /SfBYf2(90.6)
Uniclass
Access Ducting with Inset Lids
Charcon Specialist Products
STRENGTH IN INNOVATION
Stop end units
Lifting method
Access Ducting
Stop EndReference
SP 350 X 300
SP 600 X 300
80
80
500
500
609
854
70
90
Stop End Dimensions
(mm)
A D E
StopEnd
Weight(kg)
Installation ProcedureThe recommended installation procedure is as follows:-1. Prepare bed or foundation to suit ground conditions and loading.2. Position trough to line and level.3. Abut the next trough, the flat end face against the installed end face.
Bed and level the unit to suit.4. Haunch or back fill as required.5. Repeat the procedure to form the required duct length.6. Install the service within the duct.7. Position the lids in each duct unit, ensuring that there is exactly
two No. per duct.8. The units should be satisfactorily sealed using proprietary sealants
which are available from the Charcon Sales Office. Telephone 01455 288275.
Note: Lifting bar and shackle devices are also available from the Charcon Sales Office.
1. Insert lifting pinsthrough all four lifting
holes from the insidewall of the trough unit.
2. Attach locking nut and hand tighten.
3. Attach lifting hooksthrough the pin eye
at all four points.
4. Ensure lifting chains/steel ropes are symmetrical,
then begin lift.
5. Lift and place trough into position.
6. Remove shackles/hooksthen lifting device by
unscrewing the locking nut.
5
These precast units are a cost-effective,quick and easy method of constructingstop ends on site.
Transition units
Angle IronLid Support