lenovo ideacentre k330b hardware replacement guide v5.0 (english)

7/23/2019 Lenovo IdeaCentre K330B Hardware Replacement Guide V5.0 (English)

1/43

Version 5.0 2011.03

Hardware Replacement GuideIdeaCentre K3 Series

Machine type: 10062/7727 10073/1169 10066/7747

10067/7748

31048526


2/43

Hardware Replacement Guide

Copyright Lenovo 2011. All rights reserved.

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered

pursuant a General Services Administration GSA contract, use, reproduction,

or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

2011. Lenovo


3/43

Contents

Overview ..................................................................................... 1

Chapter 1 Locations ................................................................. 5

Locating components and connectors ...........................................5

Identifying parts on the system board ..........................................10

Chapter 2 Replacing hardware .............................................. 15

General information ......................................................................15

Removing the computer cover .....................................................15

Removing the front bezel .............................................................17

Replacing a memory module .......................................................18

Replacing the hard disk drive .......................................................19

Replacing an optical drive ............................................................20

Replacing the system fan assembly .............................................21Replacing the heat sink assembly ................................................24

Replacing a PCI express adapter .................................................26

Replacing the CPU ......................................................................32

Replacing the keyboard ...............................................................35

Replacing the mouse ...................................................................36

Replacing the external speaker ....................................................37

Completing the installation ...........................................................37

Chapter 3 Appendix. ............................................................... 39

Declaration ..................................................................................39

Trademarks ..................................................................................40


4/43

1Hardware Replacement Guide

Overview

This guide is intended to be used by customers who are replacing Customer

Replaceable Units (CRUs) as well as trained service personnel who are replacing

Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred

to as parts.

Note:Trained service personnel should refer to the Hardware Maintenance

Manual(HMM) for parts ordering information.

This guide does not include procedures for the replacement of all parts. It isexpected that trained service personnel are already able to replace cables, switches,

and certain mechanical parts without the need for step-by-step procedures.

Note: Use only parts provided by Lenovo.

The description of the TV-Tuner card in this manual applies only to those computer

models that have the TV-Tuner card installed, and therefore does not apply to

models without a TV-Tuner card.

This guide contains instructions for replacing the following parts:

Memory modules

Hard disk drive

Optical drive

Heatsink, Fan

CPU

VGA card

Keyboard, Mouse (wired)

External speakers

Safety information for replacing CRUs

Do not open your computer or attempt any repairs before reading the Important

safety information in the Safety and Warranty Guidethat was included with your

computer. An electronic copy of the Safety and Warranty Guide can also be

obtained online from the Lenovo Support Web site at:

http://consumersupport.lenovo.com.


5/43

2 Hardware Replacement Guide

Additional information resources

The most up-to-date information for your computer is available online at:

http://consumersupport.lenovo.com.

You can find the following information:

CRU removal and installation

Publications

Troubleshooting

Parts

Links to other useful sources of information

Tools required

To disassemble the computer, you will need the following tools:

Wrist grounding strap and conductive mat for preventing electrostatic

discharge

Flat screwdriver

Phillips screwdriver

Hex screwdriver

Plastic at screwdriver Plastic tweezers

Note:The screws used for the different components will vary in size. During

the disassembly procedure, group the screws with their corresponding

components to avoid a mismatch when replacing the components.

Handling static-sensitive devices

Static electricity, although harmless to you, can seriously damage computer

components.

When replacing a part, do not open the antistatic packaging containing the new

part until the defective part has been removed from the computer and you are

ready to install the new part.


6/43


When handling parts and other computer components, the following precautions

should be taken in order to avoid static electricity damage:

Limit your movements, as such movements can cause the build-up of static

electricity.

Always handle parts and other computer components with care, including

handling adapters, memory modules, system boards, and microprocessors by

their edges. Never touch any exposed circuitry.

Prevent others from touching the parts and other computer components.

Before replacing a new part, rst place the antistatic packaging containing the

part against a metal expansion slot cover or other unpainted metal surface on

the computer for at least two seconds. This will reduce static electricity in the

package and your body.

When possible, remove the new part from its antistatic packaging and install it

directly into the computer without setting the part down. If this is not possible,

place the part on top of its anti-static packaging on a smooth, at surface prior

to installing it.

Do not place parts on the computer cover or other metal surface.


7/43



8/43


LocationsChapter

This chapter provides illustrations to help you locate the various connectors,

controls and components in your computer. To remove the computer cover, refer

to the section in this manual entitled Removing the computer cover.

Locating components and connectors

The following illustrations will help you to locate the various components and

connectors in your computer.

Internal components

The following illustration shows the components inside your computer.

1 8

7

6

5

4

3

2


9/43


Power supply PCI Express adapter card

System fan Memory modules

Microprocessor fan and heat sink Hard disk drivePCI Express adapter connector Optical drive

Front view

The two following illustrations show the location of the connectors on the front of

the computer.

9

8

3

1

2

4

5

6

7

Power button

Power dial indicator ON/OFF

File backup button

USB connector

Microphone connector

Headphone connector

Memory card reader (selected models only)


10/43


Optical drive (some models are equipped with only one optical drive)

Power dial switch

Rear view of the chassis

The following illustrations show the location of the connectors on the rear of the

computer.

IdeaCentre K330

Voltage selection switch (Selected models only)

Power connector

PS/2 keyboard connector

PS/2 mouse connector

USB connectors (6)

eSATA connector

Ethernet connector

Audio connectors (6)

Standalone graphic card

Expansion card slots (Access connectors for any installed PCI express cards)


11/43


IdeaCentre K330A/IedaCentre K330B


Power connector



HDMI connector

USB connectors (4)

On-board VGA connector

Ethernet connector


Standalone graphic card (Selected models only)



12/43


IdeaCentre K335


Power connector



eSATA connector

USB connectors (6)

HDMI connector

On-board VGA connector

Ethernet connector


Standalone graphic card (Selected models only)



13/43


Identifying parts on the system board

The system board (also known as the mainboard or motherboard) is the main

circuit board in your computer. It provides basic computer functions and supportsa variety of devices that are factory-installed or that you can install later.

The following illustrations show the locations of the different parts on the system

board.

IdeaCentre K330

Microprocessor and heat sink

Microprocessor fan connector

Memory connectors (4)

Thermal sensor header connector

Power connector

SATA connectors (4)

eSATA connector


14/43


Power fan connector

Front panel connector

Front USB connectors (3)Serial (com2) connector

Front audio connector

PCI express X 1 adapter connectors (2)


System fan connector

12V power connector

IdeaCentre K330A






15/43


Power connector

SATA connectors (4)

Front panel connectorFront USB connectors (3)

Serial(com2) connector



PCI express X 16 adapter connector


12V power connector

IdeaCentre K330B




16/43




Power connectorSATA connectors (4)


Front USB connectors (3)

Serial(com2) connector



PCI express X 16 adapter connector

System fan connector12V power connector

IdeaCentre K335


17/43




Memory connectors (4)Thermal sensor header connector

Power connector

SATA connectors (4)

eSATA connector

Power Fan connector


Front USB connectors (3)

Serial(com2) connectorFront audio connector




12V power connector


18/43


Attention:

Do not remove the computer cover or attempt any repair before reading the

Important safety information in the Safety and Warranty Guidethat was

included with your computer or in the Hardware Maintenance Manual(HMM)

for the computer. To obtain copies of the Safety and Warranty Guideor

HMM, go to the Support Web site at http://consumersupport.lenovo.com.

Note: Use only parts provided by Lenovo.

General information

Pre-disassembly instructionsBefore proceeding with the disassembly procedure, make sure that you do the

following:

1. Turn off the power to the system and all peripherals.

2. Unplug all power and signal cables from the computer.

3. Place the system on a at, stable surface.

Removing the computer cover

Attention:

Turn off the computer and wait 3 to 5 minutes to let the computer cool

before removing the computer cover.

To remove the computer cover:

1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut

down the computer, and turn off all attached devices.

2. Unplug all power cords from electrical outlets.

Replacing hardwareChapter


19/43


3. Disconnect all cables attached to the computer. This includes power cords,

input/output (I/O) cables, and any other cables that are connected to the

computer. Refer to Locating connectors on the rear of the computer.

4. Remove the two screws that secure the computer cover at the rear of the

chassis.

5. Slide the computer cover to the rear of the chassis to remove.

Note: For this procedure, it helps to lay the computer on its side.


20/43


Removing the front bezel

To remove the front bezel:

1. Remove the computer cover. Refer to Removing the computer cover.

Note:For this procedure, it helps to lay the computer on its side.

2. Remove the front bezel by releasing the three plastic tabs inside the chassis

and push the bezel outward as shown.

3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel with the

corresponding holes in the chassis, and then snap it into position at the bottom

and top of the chassis.

4. Refer to the Completing the installation.


21/43


Replacing a memory module

Attention: Do not remove the computer cover or attempt any repair before reading the





To replace a memory module:



2. Locate the memory module connectors. Refer to Locating components.

3. Remove the memory module to be replaced by opening the retaining clips as shown.

4. Position the new memory module over the memory connector. Make sure

that the notch on the memory module aligns correctly with the connector

key on the system board. Push the memory module straight down into the

connector until the retaining clips close.



22/43


Replacing the hard disk drive






To replace the hard disk drive:



2. Disconnect the data and power cables from the hard disk drive.

3. Use the plastic handle to slide the hard disk drive out of the drive bay.

4. Slide the new hard disk drive into the drive bay.

5. Twist the drive bay into place.

6. Connect the power and signal cables to the hard disk drive. Refer to Identifying

parts on the system board.


23/43



Replacing an optical drive

Attention:





HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace an optical drive


2. Remove the front bezel. Refer to Removing the front bezel.

3. Disconnect the data and power cables from the rear of the optical drive.

4. Press the release button and push the optical drive straight out of the front of

the chassis.


24/43


5. Slide the new optical drive into the bay from the front until it snaps into

position.

6. Connect the data and power cables to the drive.

7. Install the front bezel. Refer to the steps 3 of the Removing the front bezel.

8. Install the computer cover. Refer to Completing the installation.

Replacing the system fan assembly

Attention:



included with your computer or in the Hardware Maintenance Manual(HMM)for the computer. To obtain copies of the Safety and Warranty Guideor


To replace the system fan assembly:


2. Locate the system fan assembly. Refer to Identifying parts on the system

board.

3. Disconnect the system fan assembly cable from the system board. Refer to

Identifying parts on the system board.


25/43


4. Pull the system fan assembly out of chassis.


26/43


5. Install the new system fan assembly by aligning the rubber mounts of the

system fan assembly with the holes on the chassis and push the rubber

mounts through the holes.

6. Pull on the tips of the rubber mounts until the fan assembly is in place.

7. Connect the system fan assembly cable to the system fan connector on the

system board.



27/43


Replacing the heat sink assembly





HMM, go to the Support Web site at: http://consumersupport.lenovo.com

To replace the heat sink assembly:


2. Lay the computer on its side.

3. Locate the heat sink. Refer to Identifying parts on the system board.

4. Disconnect the heat sink and the fan assembly cable from the system board.

5. Remove the four screws that secure the heat sink and fan assembly to the

system board.

6. Lift the defective heat sink and fan assembly away from the system board.


28/43


7. Use the thermal grease syringe to place five drops of grease on the top of the

microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the

grease syringe).

8. Install the new heat sink and fan assembly on the heat sink retention bracket.

9. Reconnect the disconnected cables to the system board.



29/43


Replacing a PCI express adapter





HMM, go to the Support Web site at: http://consumersupport.lenovo.com

To replace an adapter:


2. At the rear of the computer, press the release button to open the adapterlatch and remove the adapter by pulling it straight out of the adapter

connector.


30/43


3. Install the new adapter into the same adapter connector.

4. Ensure that the new adapter is fully seated into the adapter connector.

5. At the rear of the computer, turn the adapter latch to the closed position to

secure the adapter.



31/43


Note 1: Replacement of some models equipped with

graphic adapter bracket is different.

Please remove the plastic bracket first as the following:

1. Remove the two screws that secure the plastic bracket at the bottom of the

chassis.

2. Lift the plastic bracket out of the chassis.

3. Then remove the adapter as above.


32/43


After the Graphic Adapter is installed , install the bracket as the

following:

1. Install the plastic bracket into the chassis so that the screw holes in the plasticbracket align with those in the chassis. Let the slot on the plastic bracket to

clip onto the adapter.

2. Fit the two screws to secure the plastic bracket.

Note: Use only screws provided by Lenovo.


33/43


Note 2: Replacement of some models equipped with

graphic adapter bracket is different.

Please remove the bracket first as the following:

1. Remove the screw that secures the bracket at the side of the chassis.

2. Press the pin on one end of the metal bracket and pull the metal bracket

straight out of the chassis.


34/43


After the Graphic Adapter is installed, install the bracket as the

following:

1. Install the metal bracket into the chassis so that the screw hole in the metalbracket aligns with the hole in the chassis. Let the slot on the metal bracket

clip the adapter.

2. Screw back the screws on the metal bracket.

Note: Use only the screw provided by Lenovo.


35/43


Replacing the CPU






To replace an CPU


2. Remove the front bezel. Refer to Removing the front bezel.

3. Remove the system board. Refer to Replacing the heat sink assembly.

4. Remove the heat sink and fan assembly. Refer to Replacing the heat sink

assembly.

5. To remove the microprocessor from the system board, lift the small handle

and open the retainer .

Important:

Do not touch the gold contacts on the bottom of the microprocessor. When

handling the microprocessor, touch only the sides.


36/43


6. Lift the microprocessor straight up and out of the socket.

Notes:

a. Note the orientation of the notches on the microprocessor. This is

important when reinstalling the microprocessor on the new system

board.

b. Do not drop anything onto the microprocessor socket while it isexposed. The socket pins must be kept as clean as possible.

7. Make sure that the microprocessor retainer is fully open.

8. Holding the microprocessor with your fingers, remove the protective cover

that protects the gold contacts on the new microprocessor .


37/43


9. Holding the microprocessor with your fingers, position the microprocessor

so that the notches on the microprocessor are aligned with the tabs in the

microprocessor socket.

Important:

To avoid damaging the microprocessor contacts, do not tilt the microprocessor

when installing it into the socket.

10. Lower the microprocessor straight down into the system board socket of the

system board.

11. To secure the microprocessor in the socket, close the microprocessor retainer

and lock it into position with the small handle.

12. Use the thermal grease syringe to place five drops of grease on the top of the

microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the

grease syringe).

13. Install the heat sink and fan assembly on the system board.

14. Connect the heat sink and fan assembly cable to the system board. Refer to

the Identifying parts on the system board.

15. Install the system board back into the chassis and allign the screw holes with

those in the chassis. Insert and tighten the screws that secure the system

board, referring to the above section entitled Replacing the system board.

16. Reconnect the disconnected cables to the system board.



38/43


Replacing the keyboard

To replace the keyboard:

1. Remove any media (disket, CDs, or memory cards) from the drives, shut down

the computer, and turn off all attached devices.


3. Locate the connector for the keyboard. Refer to Locating connectors on the

rear of the computer and Locating connectors on the front of the computer.

Note:Your keyboard may be connected to the standard keyboard connector

at the rear of the computer or to a USB connector at either the front or

rear of the computer.

4. Disconnect the defective keyboard cable from the computer and connect the

new keyboard cable to the same connector.



39/43


Replacing the mouse

To replace the mouse:




3. Locate the connector for the mouse. Refer to Locating connectors on the

front of the computer and Locating connectors on the rear of the computer.

Note:Your mouse may be connected to the standard mouse connector at

the rear of the computer or to a USB connector at either the front or rear

of the computer.

4. Disconnect the defective mouse cable from the computer.

5. Connect the new mouse cable to the connector.



40/43


Replacing the external speaker




3. Locate the Speaker. Refer to Locating connectors on the rear of the

computer and Locating connectors on the front of the computer. Your

speaker may be connected to the audio connector at either the front or rear

of the computer. Locate the connector for the speaker.

4. Disconnect the defective speaker cable from the computer and connect the

new speaker cable to the same connector.

Completing the installationAfter replacing a new part or parts, you will need to close the computer cover

and reconnect all cables, including telephone lines and power cords. In addition,

depending on the part that was replaced, you may also need to confirm the

updated information in the Setup Utility program. Refer to Starting the Setup

Utility in the User Guideor in the Hardware Maintenance Manualfor further

information.

To complete the part installation:

1. Ensure that all components have been reassembled correctly and that no toolsor loose screws are left inside your computer. Refer to Locating components

and connectors.

2. Make sure that all cables are routed correctly before replacing the computer

cover.


41/43


3. Position the computer cover on the chassis so that the rail guides on the

bottom of the computer cover engage the rails. Then, push the computer

cover closed until it snaps into position.

4. Reconnect the external cables and power cords into the computer. Refer to

Locating connectors on the front of the computer and Locating connectors

on the rear of the computer.

5. To update your configuration settings, refer to Starting the Setup Utility in theHardware Maintenance Manual.

Note: In most areas of the world, Lenovo requires the return of the defective

CRU. Information about this will either come with the CRU or will arrive a few

days after the CRU has been delivered.


42/43


Declaration

Thank you for using Lenovo products.

Carefully read all documents shipped with your computer before you install and

use the product for the first time. Lenovo is not responsible for any loss except

when caused by installation and operations performed by Lenovo professional

service personnel. You are responsible if you fail to operate the product according

to instructions and requirements in the manuals included with your computer, or

operate the product inappropriately.

This manual could include technical inaccuracies or typographical errors. Changes

are made periodically to the information herein; these changes will be incorporated

in new editions of the publication.To provide better service, Lenovo reserves theright to improve and/or modify the products and software programs described in

the manuals included with your computer, and the content of the manual, at any

time without additional notice.

The manuals included with your computer are provided to help you use Lenovos

products appropriately. For the configuration of the product, refer to the related

contract (if any) or product packing list, or consult the distributor for the product

sales.

The content of the manuals included with your computer is protected by copyrightlaws and rules. None of the manuals included with your computer may be

reproduced or transcribed by any means or translated into any language without

prior written permission of Lenovo.

The software interface and function and hardware configuration described in

the manuals included with your computer might not match exactly the actual

configuration of the computer that you purchase.You are welcome to contact us

about the manuals included with your computer. For the latest information or any

questions or comments, contact or visit the Lenovo Web site:

Service Web site: http://consumersupport.lenovo.com

Appendix.Chapter


43/43

Trademarks

Lenovo and the Lenovo logo, IdeaCentre and IdeaCentre logo are trademarks of

Lenovo in the United States, other countries, or both.

Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of

companies.

Intel Inside is a trademark of Intel Corporation in the U.S. and/or other countries.

AMD, the AMD Arrow logo, ATI, AMD Athlon, AMD LIVE!, AMD Opteron, AMD

Phenom, AMD Sempron, Catalyst, Cool n Quiet, CrossFire, PowerPlay, Radeon,

and The Ultimate Visual Experience are trademarks of Advanced Micro Devices,

Inc.

Other company, product, or service names referred to herein or in other Lenovo

publications may be trademarks or service marks of others.

All rights reserved.

Names or marks of certain companies mentioned in the manuals included with

your computer or this document do not necessarily indicate that related software

or hardware is included. The actual configuration of the product depends on the

packing list description.

lenovo ideacentre k330b hardware replacement guide v5.0 (english)

Documents