ledpod instructions new
TRANSCRIPT
-
8/10/2019 Ledpod Instructions NEW
1/2
Wagner LumenrailLedpod
INSTALLATION AND WIRING INSTRUCTIONS:
1. Installation must be performed by a licensed electrician and allwiring must conform to local electrical code. Read all instructionsbefore beginning installation. Contact R&B Wagner, Inc. with anyquestions at 888-243-6914 or [email protected].
2. Turn off the power before terminating the Driver or fixtures. Neverperform electrical work on a live circuit.
3. Ensure all Ledpod holes are de-bured inside and out.
4. Install 24 VDC positive (+) and negative (-) wires down hand rail(fig. 1). Refer to driver spec sheet for wire gauge recommendations.
5. Pull a loop of the 24 VDC wires out of the 25mm Ledpod hole (fig.2).
6. Install the retaining spring (fig. 3).
7. Install the Scotchlocs to the 24 VDC main wires and the stepdown transformer (fig. 4). Ensure that the polarity of wires fromthe step-down transformer (+ = red, - = black) connect to thecorrect polarity main 24 VDC wires.
8. Carefully push wires, Scotchlocs, and step down transformerinto the hole (fig. 5).
9. Plug the Ledpod into the step-down transformer.
fig. 3
fig. 5
fig. 2
fig. 4 fig. 6
Spring Clip
Step-downtransformer
Scotchlocs
fig. 1
24 VDC wires
10. Carefully push the remaining wire into the hole. Push the Ledpodinto the hole. The witness mark on the Ledpod should be pointed
towards the pathway. If the Ledpod does not push in, remove andcheck spring alignment (fig. 6).
11. Mount driver in a suitable NEMA rated enclosure. Ledpods may beused in wet location if driver is mounted in suitable rated enclosureand wire connections are made with listed wet location terminationsNote: Driver must be a Listed Component, Class 2, and 24 VDC.
12. Connect the driver to the AC power mains using location appropri-ate electrical terminations. Ground the driver and enclosure usingthe mounting studs inside the enclosure.
WAGNER ARCHITECTURAL | (414) 716 8401 | [email protected] | WAGNERARCHITECTURAL.COM 2013
-
8/10/2019 Ledpod Instructions NEW
2/2
Wagner LumenrailLedpod
WAGNER ARCHITECTURAL | (414) 716 8401 | [email protected] | WAGNERARCHITECTURAL.COM 2013
Driver with Enclosure
120 - 277 Volt Input
(Conduit Entry)Secondary Feed Routed
Through Stainless Bracket
120 - 277 Volt Input
(Conduit Entry)
3M Scotchlock wire connectorsLedpod assembly
Soft Start
Relay Soft Start
Relay
Driver with Enclosure
Soft Start
Relay
120 - 277 Volt Input
(Conduit Entry)Secondary Feed Routed
Through Stainless Bracket
120 - 277 Volt Input
(Conduit Entry)
3M Scotchlock wire connectorsLedpod assembly
Soft Start
Relay
Wall Mount Wiring Diagram
Post Mount Wiring Diagram
24 VDC
100WDriver
18'
MAXIMUM DISTANCE FROM DRIVER TO FIRST LED
WIRE SIZE
DISTANCE
10AWG
120' 71' 46' 29'
12AWG
14AWG
16AWG
18AWG
Remote Distance Chart
NOTE: Wire to be supplied by installer, appropriately sized, and meeting localelectical code.
Concrete
EMBEDDED
Cover FlangeWith or Without
Set Screw
Rockite
or Kwixset
or
conduit
SURFACE MOUNT
1"
Anchor PlateWith Cover Flange
Concrete
41/2"13/16"