7/27/2019 LED lighting Osram.pdf

1/4

ST8-SD4 08.02.2011 Page 1 von 4

SubstiTUBE ST8-SD4Datasheet

www.osram.de

Technical operating data

Product Color Colortemp.

[K]

Lum. Flux

[lm]

Voltage [V] /

Frequency [Hz]

Power

[W]

Radiance-

Angle []

ST8-SD4-765 Daylight 6500 K 1550

230 V

50 Hz23,5 W 70 x 90ST8-SD4-840 White 4000 K 1200

ST8-SD4-830 Warm White 3000 K 1200

LED lamp in T8 shape with G13

socket

Length: 1.212 m; Weight: 420 g

18 high-performance OSLON LEDs

Nominal Power: 23.5 W

For operation with CCG

No rewiring necessary; Luminaire

certifications remain valid

Direct Retrofit for CCG luminaires;

replacement of lamp and included

starter Extremely robust with aluminium heat

sink and polycarbonate cover

Full integrated ECG complies to

relevant standards

Complies with safety standard for selfbalasted LED lamps IEC 62560; VDE

certificied

Up to 50.000 h lifetime

Overpower, overheat, short and open

circuit protected

FineWhite / ANSI Binning for highest

homogeneity

Not for operation with ECG, not

dimmable

Technical Features

VDE certified innovative LED-lamp, easy and

safe to use in CCG installations as direct retrofit.

Energy saving potential of up to 50% by

replacing 36W T8 fluorescent tubes.

Applicable in warehouses, supply rooms,

corridors, industry, stairways, garages, indirect

illumination etc; for applications with high

operating hours.

All Data are related to the entire lamp. Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only

reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could dif fer from the typical data.

7/27/2019 LED lighting Osram.pdf

2/4

ST8-SD4 08.02.2011 Page 2 von 4

Height [m] Diameter [m]

Illumination4000 K / 3000 K

Illumination6500 K

Emax [lx] Emed [lx] Emax [lx] Emed [lx]

1

1,99

1,44 586 236 741 298

2

3,98

2,89 147 59 185 74

3

5,96

4,33 65 26 82 33

47,955,78 37 15 46 19

5

9,94

7,22 23 9 30 12

Minimum / Maximum ratings

Ambient temperature

Ta

Operating temperature

Tc

Storage temperature

Ts

ST8-SD4-xx -30 50C -30... 75C -30 ... 85 C

Drawings

Tc

VDEREG.-Nr. D457

7/27/2019 LED lighting Osram.pdf

3/4

ST8-SD4 08.02.2011 Page 3 von 4

The SubstiTUBE must not be damaged or operated in a damaged

condition.

When operating with CCG, the included SubstiTUBE Start has to beinserted as well. If the conventional starter is not replaced the SubstiTUBE

will start blinking. Switch off immediately, the SubstiTUBE can be

damaged!

Do not use SubstiTUBE in luminaires which do not have any starter or

when the starter cannot be replaced.

The SubstiTUBE emits light only with a limited angle, not like a fluorescent

tube with 360output.

Due to the characteristic light distribution of the SubstiTUBE, the current

luminaire light characteristic will likely change. It is not guaranteed that e.g.

standards for lighting at working places will be complied to after

replacement. A photometric check of the installation is recommended.

The effective energy savings depend on the efficiency of the luminaire

setup to be replaced and should be considered individually in each case.

Particularly ballast losses are reduced to ohmic losses and are normally

only about 1 W 1,5 W.

The SubstiTUBE is protected according to IP20. Applications with external

risk of moisture and dust can be served with an adequately protected

luminaire.

SubstiTUBE may also be driven directly on line voltage. We strongly

recommend to refer to the application note for installation information.

Safety and Application notes

7/27/2019 LED lighting Osram.pdf

4/4

ST8-SD4 08.02.2011 Page 4 von 4

Make sure that the supply voltage is disconnected.

Carefully remove the fluorescent tube and starter according to the lamp holder type.

Insert SubstiTUBE

and SubstiTUBE

Start properly.

Below an example for typical lamp holder types is described

Turn the conventional lamp 90 degrees and take it out of the socket.

Remove the conventional starter by turning it.

Insert and latch the SubstiTUBE Start into starter socket.

Insert SubstiTUBE into socket and locate into position by turning 90. Check light

distribution angle.

Installation Instructions

Productname Light color EAN* VPE*

ST8-SD4-765 Daylight / 6500 K 4008321966063

10 x 1ST8-SD4-840 White / 4000 K 4008321966056

ST8-SD4-830 Warm White / 3000 K 4008321966049

Sales and Technical Support

OSRAM GmbH

Hellabrunner Strasse 1D - 81536 Mnchen Germanywww.osram.com+49 (0)89 6213-0

Sales and technical support is gi ven by thelocal OSRAM subsidiaries.On our world w ide homepage all OSRAMsubsidiaries are listed with completeaddress and phone numbers.

Further Information

Ordering guide

* EAN: Ordering number per single module

S-Unit: Module per shipping unit

Brochure A new approach to lightwww.osram.com/led-systems-downloads

1EZW001GB

Brochure Better light in every respect.

www.osram.com/led-systems-downloads

400D125GB

Flyer OSRAM SubstiTUBEwww.osram.com/led-systems-downloads

1EBW004GB

Downloads: Application note, eulumdat files www.osram.com/downloads

For further installation options please see the Application Note

http://www.osram.com/led-systems-downloadshttp://www.osram.com/led-systems-downloadshttp://www.osram.com/led-systems-downloadshttp://www.osram.com/downloadshttp://www.osram.com/downloadshttp://www.osram.com/led-systems-downloadshttp://www.osram.com/led-systems-downloadshttp://www.osram.com/led-systems-downloads