LED-FLIR20sw LED-FLIR20gr LED-FLIR20ws

20 watts High Power LED floodlight with IR motion sensor

Specifications:

Light Power supply: 180 – 240 V AC Supply frequency: 50 Hz Output: max. 20 watts Protection class: IP 54 LEDs: 12 x 1.6 watts Colour temperature: 6,200 – 6,700 K Luminous flux: 825 lm Beam angle: 100° Permitted humidity: < 93 % Ambient temperature: -10 °C to +40 °C Dimensions (HxBxD): 189 x 177 x 180 mm Weight: approx. 1.6 kg

Sensor Installation height: 1.8 m – 3.5 m PIR angle of detection: 180° Range of detection: 10 – 12 m Twilight value: 3 Lux – 2,000 Lux Duty cycle: min. 8 sec. +/- 3 sec. max. 7 min. +/- 2 min. Energy consumption: 0.45 watts (standby: 0.1 watts)

4

LED-FLIR20...

▪ 20 watts LED light is equivalent to 150 watts halogen light▪ 12 high power LEDs▪ low energy consumption ▪ lasts 100x longer than halogen lamps▪ automatic activation via twilight sensor and infrared motion sensor▪ environmentally friendly▪ IP54 protected against splash water

What to do if… ... the floodlight does not turn on a) check power supply b) check operating display: if it flashes every 4 seconds and twice every second after thisc) check, whether the operating display flashes more quickly after the signal has been received d) check whether the set twilight value is consistent with the ambient brightness

... the IR sensor is not sensitive enough a) check whether items are in the vicinity of the area of detection, which impair the reception of the signal b) check ambient temperaturec) check whether the source of the signal is in the area of detectiond) check height of installation e) check direction of motion

.... the floodlight does not turn offa) check detection area for continuous signals b) check whether duty cycle is set to max. c) check whether power supply is consistent with the technical datad) check whether appliances are in the immediate vicinity of the floodlight, which change the ambient temperature, such as central heating or air conditioning

WARNING! Please observe the following advice:- Installation should only be carried out by an electrician or trained member of staff.- Do not remove the plug or use the appliance if the cable is damaged.- This floodlight should not be exposed to shocks.- No items should be kept in the area of detection, which might impair the area of detection.- This floodlight should not be installed in the vicinity of appliances, which have an impact on the ambient temperature, such as central heating or air conditioning.- For your own safety: do not open casing if appliance does not function after installation. - To avoid damage to the product: please use 6A safety for installation.

This product is a high power floodlight with a highly sensitive infrared sensor, inte-grated circuit (IC), as well as SMT technology. This practical automatic floodlight is user friendly, safe and energy efficient. Its operation is based on the reception of infrared light in a vertically and horizontally defined area of detection. Immedia-tely after entering the detection area, the floodlight will be activated. The ambient light sensitivity can be set for “sun“ or “moon“. The installation is easy and the scope of applications is versatile. The operating display is lit when the appliance is switched on and the IR sensor is activated.

Operation - The area of detection (see diagrams) can be defined horizontally and vertically and can be set for the relevant requirements. - The twilight value can be set individually. If the ambient light drops below the twilight value and motion are detected, the floodlight will be activated. If the setting is set for “sun” (= max.), the floodlight is active day and night; if the setting is set for “moon“ (= min.) the light will only be active from a minimum brightness of 3 Lux (see function test). - Operating display: after being turned on, the operating display will flash once every 4 seconds, during a signal is received, the display will flash twice every second. - The duration of the duty cycle starts afresh with every signal. - The duration of the duty cycle, for which the light will be turned on following activation can be set for anything between a minimum of approx. 8 +/- 3 seconds to a maximum of 7 minutes +/- 2 minutes.

Installation (see diagram)- Turn power off or pull plug. - Fix mounting bracket in desired position using screws and rawl plugs. - Connect power

Functional test- Turn twilight value control clockwise to “Max.” (=sun), turn permanent activation control clockwise to „min.“. - After activation, the light will be off and the operating display will flash once every 4 seconds. After 5 – 10 seconds, the floodlight will turn on; the display will flash twice every second. If no signal is received, the twilight value control will turn off after 5 – 30 seconds and the display will return to flashing every 4 seconds. - Approx. 5 – 10 seconds after the signal was received, the light will turn on again and the will flash twice every second. The light will turn off again after 5 – 15 seconds. - Turn the twilight value control counter clockwise to min. (=moon). If the ambient light is brighter than 3 Lux, the floodlight will not turn on again after having been turned off. Cover the sensor with something suitable for blocking the light, such as a towel, etc.; the floodlight will turn on again. If no source for a signal is present in the area of detection, the floodlight will turn off again after 5 – 15 seconds.

LED-FLIR20... LED-FLIR20...

2 3

Ledino Deutschland GmbHAlbert-Einstein-Ring 2714532 Kleinmachnow (Berlin)GermanyTelefon: +49 33203 810-0 Telefax: +49 33203 810-105info@ledino.com, www.ledino.com

Im Zollhafen 2450678 KölnGermanyTelefon: +49 221 888989-0Telefax: +49 221 888989-11info@ledino.de, www.ledino.com