lecture 6a hydraulic conductivity and seepage
TRANSCRIPT
![Page 1: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/1.jpg)
CE424 GEOTECHNICAL ENGINEERING - 1: SOIL MECHANICS
Civil Engineering Department
WATER THROUGH SOILS
UST Manila
![Page 2: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/2.jpg)
Outline of this Lecture
Permeability in Soils Bernoulli’s Equation Darcy’s Law Hydraulic Conductivity Hydraulic Conductivity Tests
![Page 3: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/3.jpg)
Flow of water in Soil
Due to the existence of the inter-connected voids, soils are permeable.
The permeable soils will allow water flow from points of high energy to points of low energy.
Permeability is the parameter to characterize the ability of soil to transport water.
![Page 4: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/4.jpg)
![Page 5: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/5.jpg)
![Page 6: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/6.jpg)
![Page 7: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/7.jpg)
![Page 8: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/8.jpg)
See VIDEO
![Page 9: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/9.jpg)
Permeability in Soils
Permeability is the measure of the soil’s ability to permit water to flow through its pores or voids
It is one of the most important soil properties of interest to geotechnical engineers
![Page 10: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/10.jpg)
![Page 11: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/11.jpg)
Importance in Geotechnical Design:
It influences the rate of settlement of a saturated soil under load.
The design of earth dams is very much based upon the permeability of the soils used.
![Page 12: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/12.jpg)
Importance in Geotechnical Design:
The stability of slopes and retaining structures can be greatly affected by the permeability of the soils involved.
Filters made of soils are designed based upon their permeability.
![Page 13: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/13.jpg)
Knowledge of the permeability properties of soil is necessary to:
Estimating the quantity of underground seepage:
Solving problems involving pumping seepage water from construction excavation;
Stability analyses of earth structures and earth retaining walls subjected to seepage forces.
![Page 14: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/14.jpg)
Bernoulli’s equation
From fluid mechanics we know that, according to Bernoulli’s equation…
The total pressure in terms of water head is formed from 3 parts:
![Page 15: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/15.jpg)
Hydraulic Gradient & Darcy’s Law
Bernoulli’s Equation states that the total head, h at a point in water under motion can be given by the sum of the pressure head (p/γw), velocity head (v2/2g) and elevation head (z).
where p = pressure v = velocity g = acceleration due to gravity γw = unit weight of water
![Page 16: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/16.jpg)
Hydraulic Gradient & Darcy’s Law
In case of flow of water through a porous soil medium, the seepage velocity is small such that the velocity head component in the Bernoulli’s equation can be neglected.
The total head can therefore be adequate represented by:
zphw
+=γ
![Page 17: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/17.jpg)
Hydraulic Gradient & Darcy’s Law
Note: Piezometer is a device used to measure pore water pressure
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
![Page 18: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/18.jpg)
Hydraulic Gradient & Darcy’s Law
The relationship between pressure, elevation and total heads for flow of water through soil is presented in the figure below.
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
![Page 19: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/19.jpg)
Hydraulic Gradient & Darcy’s Law
Piezometer tubes are installed at points A and B The levels to which water rises in the tubes are known
as the piezometric levels of points A and B.
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
![Page 20: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/20.jpg)
Hydraulic Gradient & Darcy’s Law
The pressure head at a point is the length of the vertical column of water in the piezometer installed at that point.
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
![Page 21: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/21.jpg)
Hydraulic Gradient & Darcy’s Law
The elevation head of a point is the vertical distance measured form any arbitrary horizontal datum plane to that point.
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
![Page 22: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/22.jpg)
Hydraulic Gradient & Darcy’s Law
The loss of head between two points A and B is given by
hA
PA/γw
ZA
flow
L
∆h
PB/γw
ZB
HB
)()( Bw
BA
w
ABA ZPZPhhh +−+=−=∆
γγ
![Page 23: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/23.jpg)
Hydraulic Gradient & Darcy’s Law
The head loss ∆h can be expressed in a non-dimensional
form as: Where i = hydraulic gradient L = distance between points A and B
(the length of flow over which the loss of head occurred)
Lhi ∆
=
![Page 24: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/24.jpg)
Darcy's Law (1856):
In 1856, Darcy published a simple equation for the discharge
velocity of water through saturated soil. where v = discharge velocity, the quantity of water
flowing in unit time through a unit gross cross-sectional area of soil at right angles to the direction of flow.
k = coefficient of permeability i = hydraulic gradient
kiv =
![Page 25: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/25.jpg)
Darcy's Law (1856):
Darcy's law, which gives a linear relation between the discharge velocity and the hydraulic gradient, is valid in the range of laminar flow of fluid through pore spaces in the case of soils with particle sizes less than 1mm.
![Page 26: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/26.jpg)
Darcy's Law (1856):
In stones, gravels and very coarse sands, turbulent flow conditions may exist; in that case, Darcy's law can be rewritten as:
The experimental value of φ usually ranges between 0.65 and 1.
φkiv =
![Page 27: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/27.jpg)
![Page 28: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/28.jpg)
![Page 29: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/29.jpg)
![Page 30: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/30.jpg)
Darcy's Law (1856):
Darcy’s law states that how fast the groundwater flow in the aquifer depends on two parameters:
how large is the hydraulic gradient of the water
head (i=dH/dx); and
the parameter describing how permeable the aquifer porous medium –the coefficient of permeability (hydraulic conductivity) k.
![Page 31: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/31.jpg)
Darcy's Law (1856):
The minus sign in the equation denotes that the direction of flow is opposite to the positive direction of the gradient of the head.
![Page 32: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/32.jpg)
Darcy’s law
The physical description of groundwater flow in soil is the Darcy’s law.
The fundamental premise for Darcy’s law to work are: the flow is laminar, no turbulent flows; fully saturated; the flow is in steady state, no temporal variation.
![Page 33: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/33.jpg)
Hydraulic conductivity
Hydraulic conductivity is expressed in cm/sec or m/sec, and discharge is in m3.
It needs to be pointed out that the length is expressed in mm or m, so, in that sense, hydraulic conductivity should be expressed in mm/sec rather than cm/sec.
However, geotechnical engineers continue to use cm/sec as the unit for hydraulic conductivity
![Page 34: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/34.jpg)
Coefficient of Permeability, K
The coefficient of permeability, or hydraulic conductivity, k, is a product of Darcy’s Law.
![Page 35: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/35.jpg)
Coefficient of Permeability, K
The “K” depends on several factors such as Fluid viscosity Pore-size distribution Grain-size distribution Void ratio Roughness of mineral particles Degree of soil saturation
![Page 36: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/36.jpg)
Coefficient of Permeability, K
In clayey soils, the structure is an important influence on the coefficient of permeability.
The value of “k” varies over a wide range for different soils.
Some typical values of permeability coefficients are given in the table below.
![Page 37: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/37.jpg)
COEFFICIENT OF PERMEABILITY,K
Typical Values of Permeability Coefficient
Soil Type Permeability Coefficient, k (mm/s)
Clean Gravel 10 to 1000
Coarse Sand 0.1 to 10
Fine Sand 0.01 to 0.1
Silt 0.0001 to 0.01
Clay Less than 0.0001
![Page 38: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/38.jpg)
Effect of Water Temperature on k
Since the viscosity of water is a function of temperature, a change in water temperature will affect the value of the coefficient of permeability.
![Page 39: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/39.jpg)
Effect of Water Temperature on k
It is a general practice to note the temperature of water, T, during the test and use a conversion factor to express the value of k corresponding to 20° C by using the equation:
where nT= viscosity of water at T°C n20 = viscosity of water at 20°C kT = coefficient of permeability at T°C
TT
Ck
nnk
2020 =
![Page 40: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/40.jpg)
Empirical Relation For K
For fairly uniform sand (i.e., small uniformity coefficient), Hazen (1930) has proposed an empirical relation for the coefficient of permeability k (mm/s) in the form:
where c = constant that varies from 10 to 15 D10= effective size, mm k = coefficient of permeability
210cDk =
![Page 41: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/41.jpg)
Empirical Relation For K
Another simple relation was proposed by A.Casagrande for the coefficient of permeability for fine to medium clean sand.
where k = coefficient of permeability at a void ratio e k0.85 = coefficient of permeability at a void
ratio of 0.85
85.024.1 kek =
![Page 42: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/42.jpg)
![Page 43: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/43.jpg)
![Page 44: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/44.jpg)
Equivalent Permeability In Stratified Soil
Depending on the nature of soil deposit the coefficient of permeability of a given layer of
soil may vary with the direction of flow. kv1
kH1
kv2 kH2
kHn kvn
![Page 45: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/45.jpg)
Equivalent Permeability In Stratified Soil
Furthermore, in a stratified soil deposit where the permeability coefficient for a given directional flow changes from layer to layer, an equivalent permeability determination becomes necessary for simplifying calculations.
![Page 46: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/46.jpg)
Equivalent Permeability In Stratified Soil Given the following figure which shows n layers of soil with
flow in the horizontal direction:
kv1 kH1
kv2 kH2
kHn kvn
)...(12211)( nHnHHeqh HkHkHk
Hk +++=
![Page 47: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/47.jpg)
Equivalent Permeability In Stratified Soil
Given the following figure which shows n layers of soil with flow in the vertical direction:
kv1 kH1
kv2 kH2
kHn kvn
H nv
n
vv
eqv
kH
kH
kH
Hk+++
=...
2
2
1
1)(
![Page 48: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/48.jpg)
Laboratory Determination of K
The two standard types of laboratory test procedures for determining the coefficient of permeability of soil are:
the constant head test the variable (falling) head test
![Page 49: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/49.jpg)
![Page 50: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/50.jpg)
![Page 51: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/51.jpg)
![Page 52: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/52.jpg)
Constant Head Test
A typical arrangement of the constant head permeability test is shown in the figure. The water supply at the inlet is adjusted in such a way that the difference of head between the inlet and outlet remains constant during the test.
After a constant rate of flow is established, water is collected in a graduated flask for a known duration.
porous stone
soil sample
porous stone
water supply
graduated flask
![Page 53: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/53.jpg)
Constant Head Test
The total volume of water collected, Q, may be expressed as: where A = cross-sectional area of soil sample t = duration of test
Since i = h / L, where L is the length of the sample.
Constant head tests are suitable for coarse-grained soils that have high coefficients of permeability.
tkiAAvtQ )(==
AhtQLk =
![Page 54: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/54.jpg)
Constant Head Test
![Page 55: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/55.jpg)
Constant Head Test
![Page 56: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/56.jpg)
Constant Head Test
![Page 57: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/57.jpg)
Constant Head Test
![Page 58: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/58.jpg)
Falling Head Test
A typical arrangement of the falling head permeability test is shown in the figure.
Water from a standpipe flows through the soil. Initial head difference h1 at time t = 0 is recorded and water is
allowed to flow through the soil sample so that the final head difference at time t is h2.
soil sample
porous stone
porous stonestand pipe
![Page 59: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/59.jpg)
![Page 60: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/60.jpg)
Falling Head Test
The rate of flow q of the water through the sample at any time t can be given by:
where a = cross-sectional area of the standpipe A = cross-sectional area of the soil sample
dtdhaA
Lhkq −==
![Page 61: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/61.jpg)
Falling Head Test
The coefficient of permeability can be determined using the following equation:
The falling head test is appropriate for fine-grained soils
with low coefficients of permeability.
)(log)(303.22
110 h
hAt
aLk =
![Page 62: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/62.jpg)
![Page 63: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/63.jpg)
![Page 64: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/64.jpg)
![Page 65: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/65.jpg)
![Page 66: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/66.jpg)
![Page 67: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/67.jpg)
![Page 68: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/68.jpg)
Permeability test in the field The figure shows a case where the top permeable layer,
whose coefficient of permeability has to be determined, is underlain by an impermeable layer.
![Page 69: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/69.jpg)
Permeability test in the field In performing the test, water is pumped out at a
constant rate from a test well that has a perforated casing.
![Page 70: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/70.jpg)
Permeability test in the field Several observation wells are made at various
radial distances around the test well.
![Page 71: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/71.jpg)
Permeability test in the field Continuous observations of the water level in the test well
and the observation wells are made after the start of the pumping until steady state is reached.
![Page 72: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/72.jpg)
Permeability test in the field Steady state is established when the water level in
the test well and observation wells becomes constant.
![Page 73: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/73.jpg)
Permeability test in the field
The coefficient of permeability is determined as:
)(
)(log303.22
22
1
2
110
hhr
rqk
−=
π
![Page 74: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/74.jpg)
Permeability test in the field
The average coefficient of permeability for a confined aquifer can also be determined by a pumping test from a perforated well that penetrates the full depth of the aquifer and observing the water table in a number of observation wells at various radial distances.
![Page 75: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/75.jpg)
Permeability test in the field
![Page 76: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/76.jpg)
Permeability test in the field
Pumping is continued at a uniform rate q until a steady state is reached.
The coefficient of permeability in the direction of flow is given as:
)(727.2
)(log2
22
1
2
110
hhHr
rqk
−=
![Page 77: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/77.jpg)
SEEPAGE AND FLOW NETS
![Page 78: Lecture 6A Hydraulic Conductivity and Seepage](https://reader034.vdocuments.us/reader034/viewer/2022052218/545e50b6b1af9ff0588b4738/html5/thumbnails/78.jpg)
END OF PRESENTATION