ldpe film grades - qenos | home page | polyethylene lldpe film grades melt index (g/10 min) based on...
TRANSCRIPT
Polyethylene at a Glance
Fourth Edition
ISO 9001SAI GLOBAL
Lic No. QEC0272
Qenos Alkathene®
and Alkatuff®
production
ISO 9001SAI GLOBAL
Lic No. QEC0372
Qenos PolymersHDPE and MDPEproduction
Qenos Customer ServicePolyethylene Phone: 1800 805 538 Specialties, Mobil Films & Elastomers Phone: 1800 672 215
Phone: 1800 682 379 International Trade Phone: 1800 331 230Phone: 1800 063 573
Customer Service Fax: 1800 638 981Email: [email protected]
Qenos Cnr Kororoit Creek Road & Maidstone Street, Altona Victoria 3018
Phone: 61 3 9258 7333 Fax 61 3 9258 7451 www.qenos.comPublished by Qenos Corporate Affairs Department 2005 Qenos Pty Ltd ABN 62 054 196 771
HDPE Film GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 @190°C, 2.16kg
HD0811 0.06 0.9521 Supermarket check-out bags, garbage bags, kitchen tidy bags, singlet and other merchant bags, bags-on-roll and slap sheets
GM4755F 0.10 0.9492 Carry bags and liners
HDF895 0.80 0.9601 General purpose resin used as blend component in LDPE or LLDPE films to enhance stiffness
Exceed™ Metallocene LLDPE Film Grades
Melt Index (g/10 m
in)based on D
1238@
190°C, 2.16kg
Density
(g/cm3)
based on ASTM
DI505
Antiblock
Slip
Processing Aid
Heavy D
uty Bags
Stretch
Agricultural Film
General Purpose
Lamination
FFS
Freezer Film
Overw
rap
Clarity
High Perform
ance Sealing
Grades
AdditivesApplications
Refer to the Qenos website www.qenos.com for full datasheet information.
Qenos also supplies a broad range of specialty polymers. For further enquiries and contact details, see overleaf.This information is offered solely for your consideration, verification and should not be construed as a warranty or representation for which Qenos Pty Ltd assumes legal liability , except to the extent that such liability is imposed by legislation and cannot be excluded. Values quoted are the result of tests on representative samples, and the product supplied may not conform in all respects. Qenos Pty Ltd reserves the right to make any improvements or amendmentsto the composition of any grade or product without alteration to the code number. In using Qenos Pty Ltd's products, you must establish for yourself the most suitable formulation, production method and control tests, to ensure the uniformity and quality of your product is in compliance with all laws.
Qenos, Alkathene and Alkatuff are registered trademarks of Qenos Pty Ltd. Alkatuff Optimix is a trademark of Qenos Pty. Ltd.Qenos is the Australian distributor for ExxonMobil Chemical polymers.Exceed is a trademark of ExxonMobil Corporation.
Note: Exceed™ is an ExxonMobil Chemical product distributed by Qenos in Australia.
1 = Based on ASTM D1505/D2839 2 = Based on ASTM D792
Exceed 1012CA 1.0 0.912 * • • • • •
Exceed 1018CA 1.0 0.918 * • • • • • • • • •
Exceed 1018FA 1.0 0.918 * H * • • • • • • • •
Exceed 1327CA 1.3 0.927 * • • • • • • • • •
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
Alkathene® Injection LDPE Moulding Grades
Grades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 Based on D1505 @190°C, 2.16kg
XDS34 0.30 0.922 Injection moulded caps and closures
WJG117 1.7 0.918 Injection moulded caps and closures, industrial containers, and thick sections
XJF143 2.5 0.921 Injection moulded caps and closures, and thick-walled sections
LDN248 8.5 0.922 Injection moulded closures and caps
WRM124 22 0.920 Injection moulded housewares, lids and toys
WSM168 63 0.919 Injection moulded thin sections
LLDPE Injection Moulding GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 @190°C, 2.16kg
Alkatuff®
LL820 20 0.9251 Injection moulding and compounding applications
such as housewares and lids
ExxonMobil*
LL6101XR 20 0.9242 Injection moulding and compound applications requiring
medium flow
LL6101RQ 20 0.9242 Powder for compounding and injection applications
requiring medium flow
LL6201XR 50 0.9262 High flow and toughness injection moulding
applications requiring medium flow
LL6201RQ 50 0.9262 Powder for compounding and injection moulding
applications requiring high flow and toughness
1 = Based on ASTM D1505 2 = Based on ASTM D1928/4883
Alkatuff® LLDPE Rotational Moulding Grades
Grades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 based on D1505 @190°C, 2.16kg
LL711UV 3.5 0.939 Applications requiring balance of toughness and stiffness where excellent ESCR and high level UV protection required such as water and chemical tanks, septic systems and kayaks
LL722 3.5 0.939 Mouldings requiring balance of toughness and stiffness with excellent ESCR such as water and chemical tanks, septic systems and kayaks
LL705UV 5.0 0.935 Applications requiring high ESCR, toughness, stiffness and high level UV stabliser such as leisure craft, playground equipment and agricultural tanks.
LL755 5.0 0.935 Applications requiring high ESCR, toughness and stiffness
LL710UV 10 0.930 Good ESCR, high chemical resistance, toughness and UV protection suitable for intricate items and low cycle times
*ExxonMobil Chemical products distributed by Qenos in Australia.
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
HDPE Injection Moulding GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 based on D1505 @190°C, 2.16kg
HD0390 4.0 0.955 Stackable crates for transport, storage and bottles, and industrial mouldings
HD0397UV 4.0 0.955 Mouldings requiring long-term weatherability, including MGBs, crates, and industrial mouldings
HD0490 4.5 0.955 Stackable transport, storage and bottles crates, and industrial mouldings
HD0499UV 4.5 0.955 Mouldings requiring long-term weatherability, including MGBs, crates, and industrial mouldings
HD0790 7.0 0.956 Industrial pails, crates and closures
HD1090 10 0.956 Industrial pails, sealant cartridges, crates, and closures
HD1099UV 10 0.956 Crates and tote boxes requiring good UV resistance
HD2090 20 0.956 Housewares, thin-walled containers and closures
HD3690 36 0.956 Housewares, thin-walled mouldings and closures.
HDPE Blow Moulding GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 @190°C, 2.16kg
HD0840 0.03 0.9531 Large part mouldings, especially blow moulded
self-supported drums and tanks (25 - 220 litres)
HD1155 0.04 0.9531 Large part blow mouldings, including 25 litre to 220 litre
tanks and drums
GM7655 0.20 0.9492 Blow moulded containers including household and
industrial chemical (HIC). Suitable for larger part mouldings
GF7660 0.30 0.9732 Blow moulding and extrusion applications, injection
Black19 moulding of parts with very thick wall sections and simple flow paths. Yields extremely good weatherability
GF7660 0.40 0.9532 HIC containers, including detergent and
pharmaceutical bottles
GE4760 0.60 0.9582 Blow moulded water, dairy and fruit juice bottles
HD6095 0.80 0.9601 Thin walled bottles where ESCR is not a requirement,
such as dairy containers, fruit juice and cordial bottles, and packaging for powders
HD5148 0.85 0.9601 High speed dairy packaging applications and other thin
walled bottles, where ESCR is not a requirement such as milk, cream, fruit juice and cordial 1 = Based on ASTM D1505/D2839 2 = Based on ASTM D792
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
PE Wire and Cable GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 @190°C, 2.16kg
MD0592 0.12 0.9421 Designed for extrusion into a full range of wire and cable
products where natural medium density resins are required
MD0898 0.12 0.9521 Designed as a general purpose jacketing compound
for buried wires and cables where abrasion and cut-through resistance is required
1 = Based on ASTM D1505/D2839 2 = Based on ASTM D792
HDPE Tape and Monofilament GradesGrades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 based on D792 @190°C, 2.16kg
GF7740F2 0.40 0.944 Extrusion applications including stretched tape, mono- filament, tarpaulins, and over-pouches for medical solutions
Alkathene® LDPE Extrusion Coating Grades
Grades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 based on D1505 @190°C, 2.16kg
XLC177 4.5 0.922 Extrusion coating with low moisture transmission
WNC199 8.0 0.918 Extrusion coating
LDN248 8.5 0.922 High line speed extrusion coating with low extractables, low odour
LD1217 12 0.918 High line speed, low neck-in extrusion coating with low odour
PE Pipe Extrusion Grades Grades Melt Index (g/10 min) Density (g/cm3) Applications based on D1238 @190°C, 5kg
HDF193B 0.3 0.9562
High density black PE100 Type resin certified to AS/NZS4131, for use in pressure pipes and fittings
HDF193N 0.3 0.9462
High Density natural resin designed as a base for PE100 Type striping and jacket compounds
MD0898 0.6 0.9521
Medium Denisty black PE80B Type resin certified to AS/NZ4131 for use in pressure pipes and fittings
MD0592 0.6 0.9421
Medium Density natural resin designed for extrusion into a full range of pipe products
GM7655 0.6 0.9492
High Density natural high molecular weight resin designed for extrusion into a full range of non-standard pipe products
MDF169 0.9 0.9421
Medium Density natural high molecular weight resin designed for extrusion into a full range of non-standard pipe products
LL0228 1.9* 0.9203
Linear Low Density resin for use in pipe extrusion applications *Based on D1238@190°C, 2.16kg 1 = Based on ASTM D1505/D2839 2 = Based on ASTM D792 3 = Based on ASTM 1505
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
Alkathene®
LDPE Film Grades
Additives Applications
Grades
1 Based on antistat additive
Mel
t In
dex
(g/1
0 m
in)
base
d on
AST
M D
1238
@19
0°C
, 2.1
6kg
Den
sity
(g/c
m3)
ba
sed
on A
STM
D15
05
Ant
iblo
ck
Slip
Hea
vy D
uty
Shrin
k
Froz
en F
ood
Prod
uce
Car
ry B
ags
Gen
eral
Pur
pose
Ove
rwra
p
Cla
rity
Brea
d
Clin
g W
rap
Mel
t In
dex
(g/1
0 m
in)
base
d on
AST
M D
1238
@19
0°C
, 2.1
6kg
Den
sity
(g/c
m3)
bas
ed
on A
STM
D15
05
Ant
iblo
ck
Slip
Proc
essi
ng A
id
Hea
vy D
uty
Bags
Stre
tch
Agr
icul
tura
l Film
Gen
eral
Pur
pose
Gar
bage
Bag
s
Lam
inat
ion
FFS
Free
zer
Film
Pers
onal
Car
e
Ove
rwra
p
Cla
rity
XDS34 0.30 0.922 • • •
LDF433 0.45 0.925 * • •
LDD201 0.45 0.922 • • •
LDD203 0.45 0.922 * • •
LDD204 0.45 0.922 * M • •
LDD205 0.45 0.922 * H • • •
LDH210 1.0 0.922 • •
LD0128MS 1.0 0.922 * M • •
LDH215 1.0 0.922 * H • •
XJF143 2.5 0.921 • • •
LDJ226 2.5 0.922 * M1 • • •
LD0220MS 2.5 0.922 * M • •
LDJ225 2.5 0.922 * VH • • •
XLF197 5.5 0.920 • •
LD0520HS 5.5 0.920 * VH •
1 = Alkatuff Optimix™ grades
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
Alkatuff® LLDPE Film Grades
Additives Applications
Grades
LL438 0.80 0.922 * • • • • • • •
LL488 0.80 0.922 * H * • • • • • •
LL0130AB1 0.90 0.925 * * • • • • •
LL0132HS1 0.90 0.925 * VH * • • • • • • •
LL501 1.0 0.925 • •
LL601 1.0 0.925 * H • • •
LL425 2.5 0.918 •
LL525 2.5 0.935 •
LL535 3.5 0.939 •
TM
TM
Refer to the Qenos website www.qenos.com for full datasheet information.
Qenos also supplies a broad range of specialty polymers. For further enquiries and contact details, see overleaf.This information is offered solely for your consideration, verification and should not be construed as a warranty or representation for which Qenos Pty Ltd assumes legal liability , except to the extent that such liability is imposed by legislation and cannot be excluded. Values quoted are the result of tests on representative samples, and the product supplied may not conform in all respects. Qenos Pty Ltd reserves the right to make any improvements or amendmentsto the composition of any grade or product without alteration to the code number. In using Qenos Pty Ltd's products, you must establish for yourself the most suitable formulation, production method and control tests, to ensure the uniformity and quality of your product is in compliance with all laws.
Qenos, Alkathene and Alkatuff are registered trademarks of Qenos Pty Ltd. Alkatuff Optimix is a trademark of Qenos Pty. Ltd.Qenos is the Australian distributor for ExxonMobil Chemical polymers.Exceed is a trademark of ExxonMobil Corporation.
QualityEndorsedCompany
ISO 9001 Lic QEC 0272Lic QEC 0372SAI GLOBAL
TM
Polyol Brochure 101592 13/9/05 4:05 PM Page 1