lcd tvcncms.com.au/sanyo-ims/consumer-electronics/lcd32ca8z_im.pdflcd tv should never be placed near...
TRANSCRIPT
Owner’s Manual
LCD TV
MODEL LCD-32CA8ZLCD-37CA8ZLCD-42CA8Z
Inst. Manual - CA8Z.indd 1 6/27/2007 5:45:00 PM
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Install the LCD TV in a proper position. If not, it may result in a fire hazard.
Provide appropriate space on the top, sides and rear of the LCD TV cabinet for allowing air circulation and cooling the LCD TV. Minimum clearance must be maintained. If the LCD TV is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the LCD TV. Heat build-up can reduce the service life of your LCD TV, and can also be dangerous.
If the LCD TV is not to be used for an extended time, unplug the LCD TV from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
2
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this LCD TV, read this manual thoroughly and operate the LCD TV properly. This LCD TV provides many convenient features and functions. Operating the LCD TV properly enables you to manage those features and maintains it in better condition for a considerable time.Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.If your LCD TV seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section on page 37 of this booklet. If the problem still persists, contact the dealer where you purchased the LCD TV or the service center.
TO THE OWNER
Safety Precaution
Caution In InstallingHandle the LCD TV carefully when installing it and do not drop.
Locate set away from heat, excessive dust, and direct sunlight.
For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.
SIDE and TOP REAR
10 cm
10 cm
10 cm
6 cm
Inst. Manual - CA8Z.indd 2 6/27/2007 5:45:01 PM
3
SAFETY INSTRUCTIONSAll the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this LCD TV from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the LCD TV.
For added protection to the LCD TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Do no t use a t tachments no t recommended by themanufacturer as they may cause hazards.
Do not place this LCD TV on an unstable cart, stand, or table. The LCD TV may fall, causing serious injury to a child or adult, and serious damage to the LCD TV. Use only with a cart or stand recommended by the manufacturer, or sold with the LCD TV. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.
An appl iance and cart combinat ion should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the app l iance and car t combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the LCD TV on a rug, or other similar surface. This LCD TV should never be placed near or over a radiator or heat register.
This LCD TV should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
Never push objects of any kind into this LCD TV through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the LCD TV.
Do not place items such as vases containing liquid on top of the LCD TV.
Do not install the LCD TV near the ventilation duct of air-conditioning equipment.
This LCD TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this LCD TV where the cord may be damaged by persons walking on it.
Do not attempt to service this LCD TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this LCD TV from wall outlet and refer servicing to qualified service personnel under the following conditions:a. When the power cord or plug is damaged or frayed.b. If liquid has been spilled into the LCD TV.c. If the LCD TV has been exposed to rain or water.d. If the LCD TV does not operate normally by following the operating instructions. Adjust only those control that are covered by the operating instructions as improper adjust- ment of other control may result in damage and will often require extensive work by a qualified technician to restore the LCD TV to normal operation.e. If the LCD TV has been dropped or the cabinet has been damaged.f. When the LCD TV exhibits a distinct change in perfor- mance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this LCD TV, ask the service technician to perform routine safety checks to determine that the LCD TV is in safe operating condition.
Inst. Manual - CA8Z.indd 3 6/27/2007 5:45:01 PM
4
TABLE OF CONTENTS
BEFORE OPERATION 10
APPENDIX 36
PREPARATION 5
PART NAMES AND FUNCTIONS 5
CONNECTING LCD TV 7
PREVENTING THE TV FROM FALLING OVER 7CONNECTING THE AC POWER CORD 7CONNECTING OUTDOOR AERIAL 8CONNECTING A COMPUTER 8CONNECTING VIDEO EQUIPMENT 9
OPERATION OF REMOTE CONTROL 10 OPERATION RANGE 11
REMOTE CONTROL BATTERIES INSTALLATION 11ON-SCREEN MENU 12
CLEANING LCD TV 36FUNCTION OF PRODUCT SAFETY FEATURE 36TROUBLE SHOOTING 37TECHNICAL SPECIFICATIONS 38
BASIC OPERATION 15
TURNING ON/OFF LCD TV 15SELECTING INPUT SOURCE 15CHANNEL SELECTION 16CHANNEL RECALL 17RECALL/COLOUR SYSTEM 17MUTE 17 AUDIO MODE 17VOLUME CONTROL 18BASS EXPANDER 18SURROUND 18STILL 18ZOOM 19PICTURE 20 SOUND 20
MENU OPERATION 28PICTURE 28 SOUND 29TUNER 30TIME 32SETUP 33PC Adj. 34DEALER MODE 35
PREVENTING THE TV FROM FALLING 7 OVERPREVENTING THE TV FROM FALLING OVER 7
TIMER CURRENT TIMER 21 OFF TIMER 21 ON TIMER 22 ON POSITION 22PIP/POP OPERATION 23OPERATION OF REMOTE CONTROL (IN TEXT MODE) 24TEXT/TV 25TEXT REVEAL 25TEXT CANCEL 25TEXT INDEX 25TEXT SUBCODE 26TEXT SIZE 26TEXT HOLD 26TEXT RED 27TEXT GREEN 27TEXT BLUE 27
TRADEMARKSApple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
is trademark or registered trademark of HDMI Licensing,LLC.This symbol on the nameplate means the product has obtained the usufruct of HDMI by HDMILicensing,LLC.
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
Inst. Manual - CA8Z.indd 4 6/27/2007 5:45:01 PM
5
PREPARATION
PART NAMES AND FUNCTIONSFRONT
INDICATORS
INFRARED REMOTE RECEIVER
POWER INDICATOR
ON TIMER INDICATOR
INDICATORS
SIDE CONTROLS
STAND
CARE FOR USING LCD TV
Inst. Manual - CA8Z.indd 5 6/27/2007 5:45:02 PM
6
PREPARATION
PART NAMES AND FUNCTIONS
SIDE CONTROLS
SIDE TERMINALS
(Each button on the control panel has the same function with its counterpart on the remote controls. )
CHANNEL UP/DOWN buttonsUsed to Change channels.Used to select items.
VOLUME (+/-) buttonsAdjust the volume level.Adjust the value of the selected itemin the On- Screen Menu.Execute the selected menu in the On-Screen Menu.
Select an input source: TV/AV1/AV2(DVD)/PC/HDMI.
Open or close the On-Screen Menu.MENU button
INPUT button
Connect a television, video recorder or external audio amplifier to these jacks.
Connect all kinds of HDMI output equipment to this terminal.
HDMI INPUT TERMINAL
Connect video and audio output from video equipment.
Note: AV2 can be connected to composite video or DVD component terminals.1. Composite Video input: Connect to Y(V), L, R terminals.2. DVD Component input: Connect to Y(V), CB/PB, CR/PR, L, R terminals.
VIDEO INPUT TERMINALS
POWER ON/ STAND-BY button
Turn the LCD TV on or off.
Connect computer output to theseterminals.
RGB (D-SUB)Audio (L / R)
Connect the cable with a plug from aerial jack to the aerial socket on the cabinet back.
HEADPHONE JACKConnect a headphone (stereo) to this jack.When this jack is used, speaker sound will be lost.
VIDEO INPUT TERMINALSConnect video and audio output from video equipment.
PC INPUT TERMINALS
MONITOR OUTPUT TERMINALS
AERIAL JACK
Inst. Manual - CA8Z.indd 6 6/27/2007 5:45:04 PM
7
PREVENTING THE TV FROM FALLING OVER
CONNECTING THE AC POWER CORDThis LCD TV uses nominal input voltages of 100-242V AC. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.Consult your authorized dealer or service station if you are not sure of the type of power being supplied.Connect the LCD TV with all peripheral equipment before turning the LCD TV on.
CAUTIONFor safety, unplug AC power cord when the
LCD TV is not in use. When this LCD TV is connected to an outlet with AC power cord, it is in Stand-by mode and consumes a little electric power.
AC Power Cord
To the AC Outlet (100 - 242V AC)Pulls the AC power cord out from the LCD TV. The AC outlet must be near this equipment and must be easily accessible.
Carry out the steps given below to stabilize the TV that it will be safe in the event of a disaster such as an earthquake, and so that it will not fall over during normal use.
Use the marketed bands and screws to fasten the TV securely to the TV stand etc.
CONNECTING LCD TV
PREVENTING THE TV FROM FALLING OVER
TV Stand etc.
Mounting screw(Not supplied)
Band(Not supplied)
Inst. Manual - CA8Z.indd 7 6/27/2007 5:45:06 PM
8
CONNECTING LCD TV
CONNECTING A COMPUTER
IBM-compatiblecomputers or
Macintosh computers(VGA / SVGA / XGA )Desktop
typeLaptop
type
Cables used for connection (These cables are not supplied with this LCD TV.)
NOTE:When connecting the cable, AC Power Cords of both LCD TV and external equipment should be disconnected from AC outlet. Turn LCD TV and peripheral equipment on before your computer is switched on.
SIDE TERMINALS
CONNECTING OUTDOOR AERIAL
Aerial Cable
OutdoorAerial
CONNECTING OUTDOOR AERIALCable used for connectting outdoor aerial with aerial jack. ( This cable not supplied with this LCD TV.)
CONNECTING INDOOR AERIALCable used for connectting wired socket with aerial jack.( This cable not supplied with this LCD TV.)NOTE:For all aerial circuit problems please consult your local dealer.
Monitor Output
PC Cable PC
IN
Audio Cable (Mini Plug)Audio Output
(stereo)
MAC ADAPTER
PC
AU
DIO
(L /
R) I
N
HDMI Cable HD
MI I
N
HDMI Output
Digital AV Equipment
AERIAL JACK
Inst. Manual - CA8Z.indd 8 6/27/2007 5:45:07 PM
9
CONNECTING VIDEO EQUIPMENTCables used for connection (These cables are not supplied with this LCD TV.)
NOTE :When connecting the cable, AC Power Cords of both LCD TV and external equipment should be disconnected from AC outlet.
CONNECTING LCD TV
External monitor
Composite Video and Audio Output
External Audio Equipment
AudioSpeaker(stereo)
Audio Amplifier
Note :Video (RCA) output is for TV, AV or S-VIDEO only.
Video cable(RCA x1)
Audio cable (RCA x 2)
MONITOR OUT
CR
/PR
,CB/P
B,Y
Video Source (example)
Video Cassette Recorder
Video Disc Player
DVD Player
DVD (RCA x 3)
Audio cable (RCA x 2)
Component Video Source (example)DVD video equipment.(such as DVD player or high-definition TV source)
S-Video output
S-V
ideo
S-Video Cable
Video and Audio cable (RCA x 3)
Note:When AV2 input jack is connected to composite video, the connecting way is the same as AV1 input jack.You can select the signal from S-Video input or from Video input in menu operation.
R
L
R ,
L ,
V
Inst. Manual - CA8Z.indd 9 6/27/2007 5:45:07 PM
10
BEFORE OPERATION
ON/STAND-BY button
SOUND SYSTEM button
PIP ON/OFF button
MUTE button
NUMERIC buttons
SURROUND button
RECALL/COLOURSYSTEM button
SOUND button
BASS button
CHANNEL RECALL button
VOLUME + ( ) button
DIGIT button
MENU button
OPERATION OF REMOTE CONTROL
TV/AV MODE button
OK button BACK buttonMAIN/SUB button
PC MODE button
WIDE button
This button is not used.
TIMER button
CHANNEL UP / DOWN buttons
POP button
VOLUME ( +/- ) buttons
STILL button
VOLUME - ( ) buttonSTEREO/MONO button
PICTURE button
Note: In different mode, some keys have different functions. For example, STILL button in this mode has STILL function, but in Teletext mode, it has only Teletext RED function, so called "TEXT RED button". (For details, please refer to page 24.)
These buttons are used for Sanyo VCR and DVD player. Thay are have the same functions with its counterpart on Sanyo VCR's or DVD player's remote controls. Refer to the operation by the manual instruction of Sanyo VCR or DVD player to use these buttons.
CHANGE button
Inst. Manual - CA8Z.indd 10 6/27/2007 5:45:08 PM
11
BEFORE OPERATION
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING RANGE
Point Remote Control toward LCD TV (Infrared Remote Receiver) whenever pressing the buttons. Maximum operating range for Remote Control is about 16.4' (5m) in front, about 30º to the left or the right, about 15º for up or down.
INSTALLING BATTERIES 1. Remove the battery compartment cover as shown in figure. 2. Insert two size AAA batteries (1.5V) according to "+" and "-" polarity markings inside the battery compartment. 3. Close the battery compartment cover.
To insure safe operation, please observe the following precautions:
and install new batteries.
NOTE: The shape of Remote Control shall be referred to the object.
Infrared Remote Receiver
16.4'(5 m)
30 30
Inst. Manual - CA8Z.indd 11 6/27/2007 5:45:10 PM
12
BEFORE OPERATION
Picture MENU
ON-SCREEN MENU
Sound MENU
Tuner MENU
Note:"Tint" can only works in NTSC system."Tuner" can only works in TV mode. MENU LIST
BrightnessContrastColour
SharpnessWhite Tone
Tint
50
Select Adjust Return ExitMENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50505050
•••
BACK
ContrastColour
SharpnessWhite Tone
Tint
Select Adjust Return ExitMENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50505050
•••
BACK
Brightness 50
ACC/ACMCCS
MPEG NRFilm Mode
DNR
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
DCDi
TrebleBassBalance
15
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
150
BACK
Surround
Bass Expander
Auto SearchSemi-Auto SearchManual SearchColour System
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Sound SystemSkipChannel Swap •••
>>>>>>>>>
Auto Secrching
Please Wait...
1
Search Return ExitMENUBACK
Semi-Auto Searching
Please Wait...
1
Search Return ExitMENUBACK
Manual Search
1
Search Return ExitMENUBACK
Inst. Manual - CA8Z.indd 12 6/27/2007 5:45:11 PM
13
BEFORE OPERATION
MENU LIST (Continue)
Time MENU
MAIN MENU
Tuner MENU
Auto SearchSemi-Auto SearchManual SearchColour System
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Sound SystemSkipChannel Swap •••
>>>>>>>>>
BrightnessContrastColour
SharpnessWhite Tone
Tint
50
Select Adjust Return ExitMENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50505050
•••
BACK
Target ChannelSwapping
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
0>>>
Current TimeOff TimeOn TimeOn Position
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
--:----:----:--
Current Channel 3
Inst. Manual - CA8Z.indd 13 6/27/2007 5:45:12 PM
14
BEFORE OPERATION
MENU LIST
PC Adj. MENU
Note:"PC Adj." doesn't work if no signal is input in PC mode."PC Adj." can only works in PC mode.
Setup MENU
Menu Setup
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
•••PIP/POP SetupInitial Settings
•••>>>
Initial Settings
ReturnBACKConfirm OK
BrightnessContrastColour
SharpnessWhite Tone
Tint
50
Select Adjust Return ExitMENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50505050
•••
BACK
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Main SourceSub SourcePIP Position
Auto Adjust
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
>>>H-PositionV-PositionClockPhase
50505050
Mode
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
H-PositionV-PositionDurationTransparence
5050
50
Language
Teletext Lang.
Inst. Manual - CA8Z.indd 14 6/27/2007 5:45:13 PM
15
BASIC OPERATION
SELECTING INPUT SOURCESelect mode "TV", "AV1 (VIDEO / S-VIDEO)", "AV2/DVD", "HDMI", or "PC" by pressing TV/AV MODE button and PC MODE button on Remote Controls or pressing INPUT button on SIDE Controls.
2
AV2/DVD
AV1/S-VIDEO
PC
REMOTE CONTROLS
HDMI
Connect the LCD TV's AC power cord into an AC outlet.2
TURNING ON / OFF LCD TV1 Complete the peripheral connections before turning on LCD TV.
(Please refer to "CONNECTING LCD TV".)
ON/ STAND-BY button
NO SIGNAL SHUT OFFThis TV set incorporates the NO SIGNAL SHUT OFF function. If no signal is input in TV mode, "OFF 0:10" will display for about 10 minutes as the right picture, and TV will be turned off automatically.
3
ON/ STAND-BY button
Press ON/STAND-BY button on Side Controls of LCD TV or on Remote Controls to turn it ON. The POWER indicator will light up (green). Press ON/STAND-BY button again to shift it to stand-by status, the POWER indicator will become red.
SIDE CONTROLS
REMOTE CONTROLS
12 AUTO AUTO Mono
OFF 0:10
Note: It is possible to return to TV mode directly by pressing NUMERIC buttons from other input modes.
(TV mode)
INPUT button
TV/AV MODE button
PC MODE button
SIDE CONTROLS
Inst. Manual - CA8Z.indd 15 6/27/2007 5:45:14 PM
16
BASIC OPERATION
CHANNEL SELECTION
DIRECT SELECTION
To select channel 8:
08
Press "8" button.
CHANNEL UP/DOWNPressCHANNELUP/DOWN(▲▼)buttonsonSideControlsoronRemoteControlstoselectprograms.
REMOTE CONTROLS
CHANNEL UP/DOWN (▲▼) buttons
SIDE CONTROLS
CHANNEL UP/DOWN (▲▼) buttons
There are 256 channels can be selected on the LCD TV.
■For direct access to programmes using the (0-9) numeric button.
2) For selection of channel position 10 - 99. For channel position 25, press the Digit button to display "- -", then press “2” and “5” buttons.
1) For selection of channel position 0 - 9. Example: For channel position 8, press the “8” button.
To select channel 25:
Press "2" button. Press "5" button.Press Digit button.
- - 25
3) For selection of channel position 100 - 199. For channel position 125, press the Digit button twice to display "1 - -", then press “2” and “5” buttons.
To select channel 125:
Press "2" button. Press "5" button.Press Digit button twice.
12- 1251- -
2 -
CHANNEL UP/DOWN (▲▼) buttons
4) For selection of channel position 200 - 255. For channel position 225, press the Digit button three times to display "2 - -", then press “2” and “5” buttons.
Press "2" button. Press "5" button.Press Digit button three times.
22- 2252- -
To select channel 225:
Inst. Manual - CA8Z.indd 16 6/28/2007 9:49:57 AM
17
BASIC OPERATION
MUTEShould you wish to mute the sound, press MUTE button. To switch the sound back on, press MUTE button again or press VOLUME(+/-) but-tons on Side Controls or on Remote Controls.
CHANNEL RECALLPress CHANNEL RECALL button to switch between the previous channel and the current channel.For example, now you are watching channel "4", but you watched channel "2" previously. If you press CHANNEL RECALL button, chan-nel "2" will appear immediately.
REMOTE CONTROLS
RECALL/COLOUR SYSTEM
Press RECALL/COLOUR SYSTEM button on Remote Controls to display the status of LCD TV or switch colour system. Press the RECALL/COLOUR SYSTEM button repeatedly select a colour system until the optimum image can be produced.
On Position
11 PAL
BG Mono
Current Time 00: 00 Off Time 00: 00On Time 00: 00 18
AUDIO MODESimply press STEREO/MONO button to select the following audio signals: "STEREO", "MONO" , "NICAM" , "A" and "B" .
Color System
CHANNEL RECALLbutton
RECALL/COLOURSYSTEM button
STEREO/MONObutton
Sound System
REMOTE CONTROLS
REMOTE CONTROLS
REMOTE CONTROLS
Audio Mode
Channel Number
MUTE button
Inst. Manual - CA8Z.indd 17 6/27/2007 5:45:20 PM
18
BASIC OPERATION
BASS EXPANDERPress BASS button to switch the bass expander function On or Off. When it is set On, "Bass Expander On" will appear on the screen for a short while.
SURROUNDPress SURROUND button to switch the SURROUND function On or Off. When it is set ON, "Surround On" will appear on the screen for a short while.
VOLUME CONTROLTo adjust the volume value desired by pressing VOLUME(+/-) buttons on Remote Controls or on Side Controls. The volume dialogue box will appear on the screen for a short while.Press VOLUME(+) button to increase volume, and press VOLUME(-) button to decrease volume.
SIDE CONTROLS
VOLUME(+/-)buttons
VOLUME(+/-) buttons
BASS button
SURROUNDbutton
REMOTE CONTROLS
REMOTE CONTROLS
REMOTE CONTROLS
STILLPress STILL button to switch the still function On or Off.When in PIP or POP mode, this still function can still main and sub pic-ture at the same time.
REMOTE CONTROLS
Press STILL button to cancel "Still" function.
STILL PICTURE NATURAL PICTURE
STILL button
Inst. Manual - CA8Z.indd 18 6/27/2007 5:45:21 PM
19
BASIC OPERATION
ZOOM
Full
Zoom
Normal
Full
Zoom
Provides real 4 : 3 image on 16 : 9 screen.
Normal
Provides image to fit width of screen by expanding up/down/left/right of image. This function is suitable to enjoy a normal video signal (4 : 3 aspect ratio) with wide video aspect ratio of 16 : 9 screen.
Natural Wide
"Normal" and "Natural Wide" by pressing WIDE button on Remote Controls.
This function doesn't work if the picture is black out.This function doesn't work in PIP or POP mode.Only "Full" mode can be selected when the input mode is "PC" 、
"HDMI" or "DVD" and the input signal is 1080i, 720p or 1080p.
Natural Wide
ZOOM button
Provides image to fit screen size (16 : 9 aspect ratio) by expanding image width and height uniformly. This function can be used for enjoying a letter box mode picture (4 : 3 aspect picture with black bar on top and bottom edges) with wide video aspect of 16 : 9 screen.
Provides the image that is expanded as "Zoom" mode and moved up to show more image to include captions. This function can be used for enjoying a letter box picture with captions.
Provides image to fit width of screen by expanding image width uniformly. This function can be used for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen.When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select "Full" to provide better quality.
WIDEbutton
REMOTE CONTROLS
Inst. Manual - CA8Z.indd 19 6/27/2007 5:45:22 PM
20
BASIC OPERATION
PICTURESelect image level by pressing PICTURE button on Remote Controls.
Natural and splendid picture level preset on this LCD TV.
Bright and dynamic picture. It is suitable for nice playback, such as DVD program.
Inhibit strong contrast and color, it is beneficial for eye protection.
Standard
Dynamic
User presets picture adjustment in Picture mode.Personal
Soft
Personal
SOUNDSelect sound level by pressing SOUND button on Remote Controls.
Normal sound state preset on LCD TV.
Select this mode for talk programs.
Select this mode for music programs.
Standard
News
Select this mode for user to call out the preset sound adjustment in SOUND menu.
Personal
MusicMusic
Personal
REMOTE CONTROLS
REMOTE CONTROLS
Standard
Dynamic
Soft
Standard
News
EcoInhibit strong brightness and chroma, it is beneficial for eye protection.
Eco
PICTUREbutton
SOUNDbutton
Inst. Manual - CA8Z.indd 20 6/27/2007 5:45:23 PM
21
BASIC OPERATION
TIMERYou can set Current Time , Off Time , On Time and On Position functions. Only after setting Current Time, you can select another one to set. If On Time hasn't been set ,you can not select On Position.
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (Refer to "Duration"
on page 33) to exit menu operation.
Press to set time. (00:00~23:59)Press VOLUME(+/-) buttons to reset the set time.3
Press TIMER button to display Time menu.1Press VOLUME(+/-) buttons to enter into Time menu.2
To cancel "Current Time", you can choose any option of the following ways.
Setting " - - : - -" in Current Time menu.Disconnecting the AC power cord.
OFF TIMEOnce Off Timer has been set, when the set time is reached, the TV will shift to stand-by status.
Refer to "Current Time" 1-2 steps to enter into TIME menu.Press CHANNEL UP/DOWN ( ) buttons to select "Off Time".
1Press to set time. (00:00~23:59)Press VOLUME(+/-) buttons to reset the set time.2
Note:About one minute before the set time is reached, the status of LCD TV will display on the screen.
To cancel "Off Timer ", you can choose any option of the following ways.
CURRENT TIMEOnce Current Time has been set, press RECALL/COLOUR SYSTEM button, the message will display on the screen.
VOLUME(+/-) buttons
button
CHANNEL DOWN
TIMER button
Setting " - - : - -" in Off Time menu.Disconnecting the AC power cord.
Off TimeOn TimeOn Position
Input Clear Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
--:----:--
Current Time 01:10
0-9:
Off TimeOn TimeOn Position
Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
--:----:--
Current Time --:--
Input Clear0-9:
On TimeOn Position
Clear Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
0-9: BACK
--:--
Current Time 01:10Off Time 02:10
Input
Inst. Manual - CA8Z.indd 21 6/27/2007 5:45:24 PM
22
Press BACK button to return to the previous menu . Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
1
2
To cancel "On Time", you can choose any option of the following ways.
Setting "- - : - -" in On Time menu.Disconnecting the AC power cord.
ON POSITIONOnce On Position has been set, when the set time is reached, the TV will enter to the preset channel position automatically.
1
2
Note:• Enter into "Tuner", "Dealer mode" and "Teletext mode" , "Off Time" and "On Time" will be cancelled automatically.• Once "Off Time" and "On Time" has been executed, they will be cancelled automatically.
ON TIME
Once On Time has been set, when the set time is reached, the LCD TV will leave the stand-by status and enter to the preset channel position automatically.
After On Time has been set, you can go on watching other programs. When the set time is reached, the LCD TV will be displayed "Note: Time is up!" and then will automatically switch to the preset program.
Once On Time has been set, the time indicator will light green.
Once On Time has been set, you won't miss any opportunity to watch the program you like.
Refer to "Current Time" 1-2 steps to enter into Time menu.
Press to set time. (00:00~23:59)Press VOLUME(+/-) buttons to reset the set time.
Refer to "Current Time" 1-2 steps to enter into TIME menu.
Press VOLUME(+/-) buttons to select "PC" / "HDMI" / "AV2(DVD)" / "AV1/S-VIDEO" / "0-255".
Press BACK button to return to the previous menu . Press MENU button or wait for 5~60 seconds (refer to "Duration" on page 33) to exit menu operation.
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Current Time 01:10Off Time 02:10On Time 03:01
On Position
BASIC OPERATION
On Position
Input Clear Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Current Time 01:10Off Time 02:10On Time 03:01
1-9:
NO OPERATION SHUT OFFThis TV set incorporates the NO OPERATION SHUT OFF function. The LCD TV will turn off automatically after
"On Time" has been executed and the LCD TV has not been executed any operation in 2 hours.
Inst. Manual - CA8Z.indd 22 6/27/2007 5:45:25 PM
23
BASIC OPERATION
PIP/POP OPERATIONUsing PIP function, you can enjoy a TV program and an image such as HDMI input from a side terminal at the same time.Only the sound on the main picture is heard from the TV speaker or the headphone jack. The sound on the sub-picture can-not be heard.
PIP ON/OFF
1 Press PIP ON/OFF button to display sub picture. If initialization picture is HDMI input, sub picture will be defaulted with TV input. If initialization picture is not HDMI input, sub picture always be HDMI input.
Each time CHANGE button is pressed, the location of sub picture is changed as follows.
PIP ON/OFF button
POP ON/OFF
1
3
Press POP button to display two pictures. The left picture is main picture, the right picture is sub picture.
Each time POP button is pressed, the location of sub picture is changed as follows.
NOTE:Combination of the Main-picture and Sub-picture:Only HDMI can assembled with others input source.
CHANGE button
3
NOTE:Combination of the Main-pticture and Sub-picture: Only HDMI can assembled with others input source.
2 During PIP mode, pressing the MAIN/SUB button will switch main and sub picture.The sound on the main picture and the sub-picture also changes at the same time.
POP button
MAIN/SUB button
2 During POP mode, pressing the MAIN/SUB button will switch main or sub picture.The sound on the main picture or the sub picture also changes at the same time.
Press PIP ON/OFF button, exit PIP mode.4
CHANGE button MAIN/SUB button
Inst. Manual - CA8Z.indd 23 6/27/2007 5:45:27 PM
24
ON/STAND-BY button
TEXT INDEX button
MUTE button
NUMERIC buttons
TEXT REVEAL button
TEXT BLUE button
TEXT HOLD button
VOLUME + ( )button
TEXT SUBCODE button
OPERATION OF REMOTE CONTROL (IN TEXT MODE)
TEXT CANCEL button
PAGE UP / DOWN buttons
VOLUME ( +/- ) buttons
TEXT RED button
VOLUME - ( )button
Note: In different mode, some keys have different functions. For example, TEXT RED button in TEXT mode has Teletext RED function, but in TV/AV/PC/HDMI mode, it has STILL function, so called "STILL button". (For details, please refer to page 10.)
BASIC OPERATION
TEXT YELLOW button
TEXT GREEN button
TXT / TV button
Inst. Manual - CA8Z.indd 24 6/27/2007 5:45:27 PM
25
TEXT/TVPress TXT/TV button to select teletext. Press again will display:
Note:
(it superimposed) are displayed simultaneously.
image is displayed. However, the available key are the same as TEXT mode.the TXT/TV button is invalid.
mode will be canceled, and it will become a TEXT screen.
REMOTE CONTROLS
TXT/TV button
BASIC OPERATION
TEXT REVEAL Press REVEAL button to reveal hidden items on the text page. Some pages such as quiz pages have the answers hidden. The
button may have to be held to keep the answer on the screen, or press again to remove the answer.
In REVEAL OFF, this indication is not given. REVEAL button does not work except a text function. (The recall
button usually operates.)
REMOTE CONTROLS
TEXT CANCEL When press the TEXT CANCEL button in TEXT or MIX mode, the TV
picture appears on the screen.CANCEL mode will be canceled if the button pressed once again.
CANCEL mode is also canceled by the TXT/TV button. In CANCEL mode, "CAN" is always displayed on the screen upper left.
REMOTE CONTROLS
TEXT INDEX Press the INDEX button to select one of the teletext index page in TEXT, MIX, CANCEL mode.
REMOTE CONTROLS
TEXT REVEAL button
TEXT CANCEL button
TEXT INDEX button
Inst. Manual - CA8Z.indd 25 6/27/2007 5:45:29 PM
26
TEXT SUBCODE 1 Press TEXT SUBCODE button, “110/. . . .” will be displayed (e.g. the current page is 110).2 Press the NUMERIC buttons(0-9) to enter the sub page. For example, to select sub page 4, press NUMERIC buttons 0-0-0-4, and "110/0004" will be displayed.
REMOTE CONTROLS
TEXT SIZE Press TEXT SIZE button to enlarge the top half of the text page.Press TEXT SIZE button again to enlarge the bottom half of the text page.Press TEXT SIZE button again to return to the normal size page.
Note:
become the normal mode and a page will be requested.
it will still at the top half enlargement mode. (A HOLD symbol display )
mode, it will still at the bottom half enlargement mode. (A HOLD symbol not display )
REMOTE CONTROLS
BASIC OPERATION
TEXT HOLD Press TEXT HOLD button to stop page request and updating .
The symbol will appear instead of the page number.Update of TELETEXT is forbidden. It stops on the TEXT screen display now.
A status display will be page number display.
REMOTE CONTROLS
TEXT SUBCODE button
TEXT SIZE button
TEXT HOLD button
Inst. Manual - CA8Z.indd 26 6/27/2007 5:45:30 PM
27
TEXT RED The page of a red prompt is required. (also cancel mode) REMOTE CONTROLS
TEXT GREEN The page of a green prompt is required. (also cancel mode)This button does’t work except for TEXT mode .
REMOTE CONTROLS
TEXT YELLOW The page of a yellow prompt is required. (also cancel mode)This button does’t work except for TEXT mode .
REMOTE CONTROLS
TEXT BLUE The page of a blue prompt is required. (also cancel mode) REMOTE CONTROLS
BASIC OPERATION
TEXT RED button
TEXT GREEN button
TEXT YELLOW button
TEXT BLUE button
Inst. Manual - CA8Z.indd 27 6/27/2007 5:45:31 PM
28
MENU OPERATION
Press MENU button and the main menu will appear.12
desired.3Press VOLUME(+/-) buttons to adjust value.4
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
BrightnessPress VOLUME(-) button to adjust image darken and VOLUME(+) button to adjust image brighten. (0~100)
SharpnessPress VOLUME(-) button to soften the image and VOLUME(+) button to sharpen the image. (0~100)
White ToneThis function is used for selecting white tone. Select "Standard", "Warm" or "Cool" with VOLUME(+/-) buttons.
Advanced SettingsPress VOLUME(+/-) buttons to enter Advansed Settings menu. It can adjust "DCDi", "ACC/ACM", "CCS", "DNR", "MPEG NR" and "Film Mode".
DCDi(Directional Correlational Deinterlacing): Processing moving angled edge in deinterlacing to get smoothest and most natural image.
ACC/ACM(ACC:Adaptive Contrast and Color; ACM-II: Active Color Management-II): Adaptive Brightness, Contrast and tone control.
CCS(Cross Color Separation): This function removes residual chroma information from luminance signal which is the result of imperfect decoding of composite video.
DNR(Digital Noise Reduction):This function is available for noise reduction.
MPEG NR(MPEG Noise Reduction): Removes unwanted ringing and block noise from images that have undergone MPEG or JPEG compression and decompression.
Film Mode(Inverse 3:2 pulldown): Film vs.Video-Detect fi lm. Performed on material which underwent technologic conversion to video.
Press VOLUME(-) button to decrease contrast and VOLUME(+) button to increase contrast. (0~100)
Contrast
Press VOLUME(+/-) buttons to enter into PICTURE menu. (Whenever this menu is accessed initially, Brightness will be the default selection.)
PICTUREMAIN MENU (PICTURE MENU)
BrightnessContrastColour
SharpnessWhite Tone
Tint
50
Select Adjust Return ExitMENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50505050
•••
BACK
ContrastColour
SharpnessWhite Tone
Tint
Advanced Settings
Picture
Sound
Tuner
Time
Setup •••
Brightness
ACC/ACMCCS
MPEG NRFilm Mode
DNR
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
DCDi
ColourPress VOLUME(-) button to decrease colour and VOLUME(+) button to increase colour. (0~100)
ContrastColour
SharpnessWhite Tone
Tint
Picture
Sound
Tuner
Time
Setup
Brightness
Advanced Settings •••
TintPress VOLUME(+/-) buttons to obtain proper tint. (0~100)
Note: "TINT" doesn't work in HDMI mode."TINT" cannot be adjusted except in NTSC or NTSC4.43 system. "COLOUR" , "TINT" and "SHARPNESS" are not work in PC mode.
Select Adjust Return ExitMENUBACK
PC Adj.
Select Adjust Return ExitMENUBACK
PC Adj.
Inst. Manual - CA8Z.indd 28 6/27/2007 5:45:32 PM
29
MENU OPERATION
SOUNDPress MENU button and the main menu will appear.1Press VOLUME(+/-) buttons to enter into SOUND menu. (Whenever this menu is accessed initially, TREBLE will be the default selection.)
2
3 desired.
4 Press VOLUME(+/-) buttons to adjust value.
5 Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration"
on page 33) to exit menu operation.
BassPress VOLUME(-) button to decrease low frequency sound, and VOLUME(+) button to increase low frequency sound. (0~31)
TreblePress VOLUME(-) button to decrease high frequency sound, and VOLUME(+) button to increase high frequency sound. (0~31)
BalanceAdjust the balance of the left and right channels. (-15~15)
MAIN MENU(SOUND MENU)
BassBalance
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
15 0
BACK
Treble 15
TrebleBassBalance
15
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
150
BACK
Surround
Bass Expander
Surround
Bass Expander
SurroundSwitch Surround on or off.
Bass ExpanderSwitch Bass Expander on or off.
Inst. Manual - CA8Z.indd 29 6/27/2007 5:45:33 PM
30
MENU OPERATION
MAIN MENU(TUNER MENU)
TUNERPress MENU button and the main menu will appear. Press 1
2
desired.3
Press VOLUME(+/-) buttons to adjust the item.4 Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
All receivable channels are automatically tuned in and memorized in consecutive programme position.
pressing MENU button.
will automatically return to programme position “1”.
Auto Search
Press VOLUME(+/-) buttons to enter into Tuner menu. (Whenever this menu is accessed initially, Auto Search will be the default selection.)
Auto SearchSemi-Auto SearchManual SearchColor System
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Sound SystemSkipChannel Swap •••
>>>>>>>>>
Semi-Auto SearchManual SearchColor System
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Sound SystemSkipChannel Swap •••
>>>>>>
Auto Search >>>
Use to preset a receivable channel in any desired programme position, e.g. the position with the same number as the channel.1 Select channel “6”.
2 Enter into "Tuner" menu, pressing the CHANNEL UP/DOWN
3 Press VOLUME(+/-) buttons to start the channel searching.
The VOLUME(+) button will move tuning toward the higher frequencies, and the VOLUME(-) button will move tuning toward the lower frequencies.
Press and release the VOLUME(+) or (-) button to search for required TV station. Once a station is located, tuning will automatically stop. Continue till desired channel is located.
Press BACK button to return to the previous menu. Press MENU button to exit menu operation.
Semi-Auto Search
Auto Secrching
Please Wait...
1
Search Return ExitMENUBACK
Semi-Auto Searching
Please Wait...
1
Search Return ExitMENUBACK
AUTO SEARCH MENU
SEMI-AUTO SEARCH MENU
Note:
the main picture is TV mode .
Inst. Manual - CA8Z.indd 30 6/27/2007 5:45:33 PM
31
MENU OPERATION
This feature is used to remove unwanted channels from the channel scanning memory.You can skip the unused or undesired channels when you are select-ing a channel using CHANNEL UP/ DOWN ( ) buttons.
For example, to skip Program "04" :
02 03 05
skip
Skip
Select "AUTO" , "PAL", "SECAM" ,"NTSC" or "NTSC4.43" by pressing VOLUME(+/-) buttons.
Color System
Manually tune a channel if it cannot be automatically tuned, such as when the signal is poor.1 Select channel “6”.
2
3 Press VOLUME(+/-) buttons to start the channel searching.
The VOLUME(+) button will move tuning toward the higher frequencies, and the VOLUME(-) button will move tuning toward the lower frequencies.
Press and hold the VOLUME(+) or (-) button to search for required TV station.
Press BACK button to return to the previous menu. Press MENU button to exit menu operation.
Manual Search
When the clear sound could not be obtained, select "AUTO", "B/G", "D/K", "I" or "M" by pressing VOLUME(+/-) buttons.
Sound System
Manual Search
1
Search Return ExitMENUBACK
MANUAL SEARCH MENU
1 Select channel “4”.
2 Follow steps 1-2 on page 30 to enter into "Tuner" menu, pressing
3 Press VOLUME(+/-) buttons to select "On". (If you want to cancel the skip channel, please select "Off".)
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Du-
ration" on page 33) to exit menu operation.
04
Note:You can also use the SOUND SYSTEM button to select suitable
sound system directly.When the selecting sound system is AUTO, it will detect receiving
sound system automatically and may change the reception sound system of this LCD TV.
If the selecting sound system is not suitable, the sound may lost from the TV set. Selecting the suitable sound system may improve the sound quality.
Inst. Manual - CA8Z.indd 31 6/27/2007 5:45:34 PM
32
MENU OPERATION
Channel SwapTo swap the channels between two stored programme positions.
Press MENU button to display the main menu.1
Press VOLUME(+) buttons to enter into the Channel Swap menu. Press CHANNEL UP/ DOWN ( ) buttons to select the Current Channel or Target Channel, then Press VOLUME(+,-) buttons to adjust the swap channel. And then press CHANNEL UP/ DOWN ( ) buttons to select Swapping item, then press VOLUME(+,-) buttons to select "OK".
4
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
Semi-Auto SearchManual Search
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Skip
>>>>>>
Auto Search >>>
Color System
Target ChannelSwapping
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
0>>>
CHANNEL SWAP MENU
Sound System
Channel Swap •••
Current Channel 3
Press CHANNEL UP/ DOWN ( ) buttons to select the Tuner Menu item.2Press VOLUME(+) button to enter into the Tuner menu.Press CHANNEL UP/ DOWN ( ) buttons to select Channel Swap item.
3
Target Channel
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
0Current Channel 3
Swapping >>>
TIMEPress MENU button and the main menu will appear. Press 1
2
Follow all steps on p21-22 to setup each item.3 Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
Press VOLUME(+/-) buttons to enter into Time menu. (Whenever this menu is accessed initially, Current Time will be the default selection.)
Current TimeOff TimeOn TimeOn Position
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
--:----:----:--
Inst. Manual - CA8Z.indd 32 6/27/2007 5:45:34 PM
33
SETUP
Press MENU button and the main menu will appear. Press CHANNEL UP/ DOWN ( ) buttons to select Setup.1Press VOLUME(+/-) buttons to enter into Setup (Whenever this menu is accessed initially, Menu Setup will be the default selection.)
2
desired.3Press VOLUME(+/-) buttons to adjust value.4
Menu SetupLANGUAGE: Press VOLUME(+/-) buttons to choose English or Russian for Language menu display.H-POSITION: MENU moves to the left side when VOLUME (-) button is pressed. MENU moves to the right side when VOLUME (+) button is pressed. (0~100)V-POSITION: MENU moves up when VOLUME (-) button is pressed. MENU moves down when VOLUME (+) button is pressed. (0~100)DURATION: Use this function to set the display time of the MENU when there is no operation on the TV. Press VOLUME(-) button to decrease time, press VOLUME(+) button to increase time. (5~60 seconds) TRANSPARENCE: The background of MENU darkens when VOLUME(-) button is pressed. The background of MENU lightens when VOLUME(+) button is pressed. (0~100)
MAIN MENU SETUP MENU
MENU OPERATION
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
Menu Setup
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
•••PIP/POP SetupInitial Settings
•••>>>
Initial Settings
ReturnBACKConfirm OK
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
PIP/POP SetupInitial Settings
•••>>>
Menu Setup •••
PIP/POP SetupMODE: Press VOLUME(+/-) buttons to choose OFF, PIP1, PIP2 or POP.MAIN SOURCE: Press VOLUME(+/-) buttons to setup Main Source.SUB SOURCE: Press VOLUME(+/-) buttons to setup SUB Source.PIP POSITION: Press VOLUME(+/-) buttons to choose Bottom Right, Bottom Left,Top Left or Top Right.Note:
assembled with others input source.
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
Main SourceSub SourcePIP Position
Mode
INITIAL SETTINGSThis function returns all setting values except for Dealer Mode and channel messages by using this function.
PIP/POP SETUP MENU
INITIAL SETTINGS MENU
MENU SETUP MENU
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
H-PositionV-PositionDurationTransparence
5050
50
Language
Teletext lang.
TELETEXT lang.Press VOLUME(+/-) buttons to choose Arabic, Farsi, Western, Eastern or Russian for Language display in Teletext mode.
Teletext lang.
Inst. Manual - CA8Z.indd 33 6/27/2007 5:45:35 PM
34
MENU OPERATION
PC Adj.
Press MENU button and the main menu will appear. Press CHANNEL UP/ DOWN ( ) buttons to select PC Adj.1Press VOLUME(+/-) buttons to enter into PC Adj. (Whenever this menu is accessed initially, Auto Adjust will be the default selection.)
2
desired.3Press VOLUME(+/-) buttons to adjust value.4
PC Adj. MENU
Auto Adjust
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
>>>H-PositionV-PositionClockPhase
50505050
Select Adjust Return ExitMENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
BACK
H-PositionV-PositionClockPhase
50505050
Auto Adjust >>>
Auto AdjustPress VOLUME(+/-) buttons , and the TV automatically detects incoming signal, and adjust itself to optimize its performance. If the image is not displayed properly, a manual adjustment is required (Refer to following adjustments).
H-PositionThe horizontal picture position will be moved to the left side by pressing VOLUME(-) button. And it will be moved to the right side by pressing VOLUME(+) button.(0~100)
V-PositionThe vertical picture position will be moved to the down side by pressing VOLUME(-) button. And it will be moved to the up side by pressing VOLUME(+) button. (0~100)
ClockEliminate flicker from the image. Press VOLUME(+/-) buttons to adjust Clock. (0~100)
Press BACK button to return to the previous menu. Press MENU button or wait for 5~60 seconds (refer to "Duration" on
page 33) to exit menu operation.
PhaseEliminate disorder from the image. Press VOLUME(+/-) buttons to adjust Phase. (0~100)
"PC Adj." doesn't work expect for PC mode. "PC Adj." doesn't work if no signal is input in PC mode.
Note: "Tuner" doesn't work in PC mode. "Colour" , "Tint" and "Sharpness" are not work in PC mode.
Inst. Manual - CA8Z.indd 34 6/27/2007 5:45:35 PM
35
MENU OPERATION
DEALER MODE
Press VOLUME(+/-) buttons to select a maximal volume.1
VOLUME LOCK will be the default selection. (When you adjust others, pressCHANNELUP/DOWN(▲▼)buttons toselect theitem desired.)
3
Press VOLUME(+/-) buttons to select "ON". (The maximal volume is the set value by step 1.)4
DEALER MODE MENU
The Dealer Mode has 5 different modes : Volume Lock, Tuning Lock, Start Select, Child Lock and Reset.
MENU button
Press CHANNEL UP/DOWN/LEFT/RIGHT(▲▼◄►)buttons
SIDE CONTROLS
REMOTE CONTROLSVolume LockThis function is used to limit the maximal volume.
Tuning LockThe way to prevent owner from executing the Tuning function.
Start SelectSelect the boot-strap mode desired by this function. You can choose "OFF", "TV", "AV1", "AV2(DVD)", "HDMI" or "PC".
Child LockTo lock the buttons except for ON/STAND-BY button on the Side Controls. When select "ON", only the buttons on the remote controls can be used.
ResetThis function returns all setting values to the factory default settings.
RECALL/COLOUR SYSTEM button
TO DISPLAY DEALER MODE:
Press and hold Menu button on Side Controls, and then press RECALL/COLOUR SYSTEM button on remote controls to display Dealer mode menu.
Take the way of setting VOLUME LOCK for example:
Press and hold Menu button on Side Controls, and press RECALL button on remote controls to display Dealer mode menu.
2
Press menu button to exit menu operation.5
Adjust ExitMENU▲▼ ◄►
◄Off►◄Off►◄AV1►◄Off►
DEALER MODEVolume LockTuning LockStart SelectChild LockReset >>>
Select
Inst. Manual - CA8Z.indd 35 6/28/2007 9:50:14 AM
36
APPENDIX
Be sure to disconnect the AC Power cord from AC outlet before cleaning the LCD TV.Clean your LCD TV as follows:
The screen is likely to be damaged if it is not maintained properly. Do not use hard objects like a hard cloth or paper. Do not use solvents or abrasions.
CAUTION :Do not use benzene, thinner, or any volatile substances to clean the LCD TV. These chemicals may damage the cabinet finish.
AUTO POWER OFFWhen a trouble is detected in the LCD TV, the protection function works and turn the LCD TV OFF automatically. When the LCD TV is turned OFF with this function, the POWER indicator becomes red and LCD TV's power cannot be turned ON.Disconnect Power cord and contact sales dealer where you purchased the LCD TV or the service center.
To turn on LCD TV again for checking:1) Disconnect Power cord from AC outlet and plug it on again.2) Refer to "TURNING ON/OFF LCD TV" on Page 15 to attempt to turn on LCD TV. If LCD TV is not turned on, disconnect Power cord and contact to service center.
CLEANING LCD TV
FUNCTION OF PRODUCT SAFETY FEATUREFor protecting product safety, protection feature provided inside LCD TV. Refer to the following please.
Inst. Manual - CA8Z.indd 36 6/27/2007 5:45:36 PM
37
APPENDIX
TROUBLESHOOTINGBefore calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected LCD TV to your equipment as described in the section "CONNECTING LCD TV" .
2. Check cable connection. Verify that all external equipment and power cords are properly connected.3. Verify that all power is switched on.4. If LCD TV still does not produce an image, re-start the external equipment.5. If the image still does not appear, unplug LCD TV from the external equipment and check the external
equipment. The problem may be with your graphics controller rather than with LCD TV. (When you reconnect LCD TV, remember to turn the external equipment and TV off before you power up LCD TV. Power the equipment back on in order of : LCD TV and external equipment.)
6. If the problem still exists, check the following chart.
Remote Control does not work
■Checkthebatteries.■MakesurenothingisbetweentheRemoteReceiverandtheRemoteControl.■ Make sure youarenot too far fromLCDTVwhenusingRemoteControl. Maximum
operating range is 16.4' (5m).■IsdirectsunlightorstrongartificiallightshiningonLCDTV'sInfraredRemoteReceiver?
Eliminate the light by closing curtains, pointing the light in a different direction, etc.
No image ■ChecktheconnectionbetweentheexternalequipmentandLCDTV.■WhenturningLCDTVon,ittakesafewsecondstodisplaytheimage.■ Check thesystemthatyouselect iscorrespondingwith theexternalequipmentor the
video equipment.■MakesurethetemperatureisnotoutoftheOperatingTemperature(0°C~40°C).■Turnoffpower,thenturnonagain,re-startLCDTV.
No sound ■CheckAudiocableconnectionfromAudioinputsource.■AdjusttheAudiosource.■PressVOLUME(+)button.■PressMUTEbutton.
There are tiny black points and/or bright point on the TV
■Darkorbrightpointsof light(red,green,orblue)mayappearonthescreen.This isacharacteristic of the LCD panels, not a malfunction of the LCD TV.
■ LCDpanel is beingproducedwith very highaccuracy technology.There is 99.99%ormoredotpixel,but there isalso0.01%or lessofdotpixel lackordotpixel that isconstantly lighted. This is not defect.
■RegardingLCDpanelcharacteristic,itmayoccurpictureremain(looklikeamirror)when the screen is changed if it displays same screen for a long time. Changing the picture or turn-off the power supply may recover.
■Stripepattern(moire,interferencestripes)mayshowuponthescreendependonthereflected picture.
Abnormal color of image
■Adjustthevalueofcolor.■Selectdifferentcolorsystem.
NO POWER ■PlugthisLCDTVintotheACoutlet.■PressON/STAND-BYbuttononSIDEControloronRemoteControltoopenthisLCD TV. ■CheckPOWERIndicator.Ifthisindicatorflashes,LCDTVhasanytrouble.
Problem: Try these Solutions
WARNING :High voltages are used to operate this LCD TV. Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions, contact the sales dealer where you purchased LCD TV or the service center. Give the model number and explain the difficulty. We will advise you how to obtain service.
Inst. Manual - CA8Z.indd 37 6/28/2007 9:50:14 AM
38
TECHNICAL SPECIFICATIONS
APPENDIX
Maximum Visible Range 32CA8Z 80cm 37CA8Z 94cm 42CA8Z 107cm Screen Diagonal SizePicture Resolution: WXGA 1366(H) x 768(V)Viewable Angle(L /3) L/R ± 89D, U/D ± 89D
Contrast LCD-32/37CA8Z : 1200:1 ; LCD-42CA8Z : 1500:1
Voltage and Power Consumption AC100-242V 50/60Hz LCD-32CA8Z:140W; LCD-37CA8Z:158W; LCD-42CA8Z:241WPower Management VESA DPMS Colour System PAL/NTSC/NTSC4.43/SECAMSound System D/K I M B/GChannel Coverage - VHF: 21-69, A14-A69, J13-J62 - UHF: E2-E12, R1-R12, K1-K9, J1-J12, A2-A13 - CATV: S1-S41, X, Y, Z, Z+1, Z+2
Speaker Size 6cm x 12cm x 2pcsSound speciality Left and Right audio input : Maximum Input Power is 9W
Input terminals PC Input Terminal : RGB X 1 HDMI terminal x1
Audio Mini stereo jack x 1 (Audio input of PC) Video Composite video terminals x2 1Vp-p
* AV2 Video input is combined with component Y input. S-VIDEO input: DIN 4-pin Jack x1 DVD input Component Y CB/PB CR/PR input x 1
Audio input: R/L x 4
Output terminals Video Monitor Output: RCA jack x 1 Audio Monitor Output: L/R Stereo Output (RCA jack) x 1 set Headphone Jack : Mini stereo jack x1
Dimensions Width x Height x Depth LCD-32CA8Z 819mm X 624mm X 271mm Including Stand LCD-37CA8Z 935mm X 695mm X 271mm Including Stand LCD-42CA8Z 1049mm X 758mm X 271mm Including StandNet Weight including Stand LCD-32CA8Z <14.5KG LCD-37CA8Z <19.6KG LCD-42CA8Z <25.4KGOperating Environment Operating Temperature 0ºC~40ºC(32ºF~104ºF)
Storage Temperature -10ºC~50ºC(14ºF~122ºF)
Inst. Manual - CA8Z.indd 38 6/27/2007 5:45:37 PM
39
APPENDIX
CONFIGURATIONS OF PC TERMINALS
PC IN (D-SUB) TERMINALTerminal : D-SUB15 PIN Connect video output terminal of LCD TV to this terminal with PC Cable (not supplied). When connecting Macintosh computer, the MAC Adapter (not supplied) is required.
Pin Configuration Red Input
Ground (Horiz.sync.)
Green Input
Sense 2Blue Input
Ground (Red)Ground (Green)Ground (Blue)
1
5
2
43
678
No Connect
Horiz. sync.
Ground (Vert.sync.)
Sense 1Sense 0
Vert. sync.Reserved
9
13
10
1211
1415
Note:
please make adjustments about phase, clock and so on.
sometimes it can display a signal very similar with one of the signal described.
mode.
recommended to select 60Hz V-Freq. of your computer to display better pictures.
In case of the following things, some messages will display on the screen.When the input signal from PC is out of the display range, "Out of range " will display.
This LCD TV can correspond to the signals below. After connecting with the computer, LCD TV can automatically recognize the signal from the connected PC( computer)/ HDMI.
PC SIGNAL MODE COLUMN (recommended)
SIGNAL MODE COLUMN (recommended)
Interlace
5 123410 9 678
15 14 13 1112
Inst. Manual - CA8Z.indd 39 6/27/2007 5:45:38 PM
APPENDIX
When input signal is digital from HDMI or DVD terminal, refer to the chart below.
57.5106084*027I0846.5105675*027I6755.1306084*027P0842.1305675*027P675
5406027*0821P0275.7305027*0821P0277.33060801*0291I08011.82050801*0291I0801
1080P1080P
0801*02910801*0291
0605
56.267.5
FrameFrequencyResolutionNO.
Audio Freq. Format :HDMI Signal Standard : HDMI1.0.
DVD SIGNAL MODE COLUMN (recommended)HDMI SIGNAL MODE COLUMN (recommended)
Part No. 1AA6P1P5451-- N5KV (UH2 - B) SANYO Electronics CO., Ltd.
Inst. Manual - CA8Z.indd 40 6/27/2007 5:45:39 PM