lc-32d30m

TopPage

LC-32D30M-BK/WH/RD

SERVICE MANUALNo. S48I5LC32D30M

LCD COLOUR TELEVISION

MODELS

LC-32D30M-BK LC-32D30M-WH LC-32D30M-RD

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

CONTENTSSAFETY PRECAUTION IMPORTANT SERVICE SAFETY PRECAUTION............................................................ i PRECAUTIONS FOR USING LEAD-FREE SOLDER ................................................................... ii SPECIFICATIONS SPECIFICATIONS ....................................................iii CHAPTER 1. OPERATION MANUAL [1] OPERATION MANUAL ..........................................1-1 CHAPTER 2. DIMENSIONS [1] DIMENSIONS ........................................................2-1 CHAPTER 3. REMOVING OF MAJOR PARTS [1] REMOVING OF MAJOR PARTS ...........................3-1 CHAPTER 4. ADJUSTMENT [1] ADJUSTMENT PROCEDURE ...............................4-1 [2] PUBLIC MODE SETTING PROCEDURE..............4-8 CHAPTER 5. TROUBLESHOOTING TABLE [1] TROUBLESHOOTING TABLE...............................5-1 CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM [1] OVERALL WIRING DIAGRAM ..............................6-1 [2] SYSTEM BLOCK DIAGRAM .................................6-2 CHAPTER 7. PRINTED WIRING BOARD ASSEMBLIES [1] MAIN Unit...............................................................7-1 [2] KEY Unit.................................................................7-5 [3] R/C, LED Unit.........................................................7-5 [4] MINI AV Unit...........................................................7-6 CHAPTER 8. SCHEMATIC DIAGRAM [1] DESCRIPTION OF SCHEMATIC DIAGRAM .........8-1 [2] KEY Unit.................................................................8-2 [3] MAIN Unit...............................................................8-3 [4] R/C, LED Unit.......................................................8-19 [5] MINI AV Unit.........................................................8-20 Parts Guide

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

LC-32D30M-BK/WH/RDLC-32D30M-BK/WH/RD

SAFETY PRECAUTIONIMPORTANT SERVICE SAFETY PRECAUTION

Service Manual

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:

WARNING1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing.

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must be used only for the purpose of completing these checks.) Any reading of 0.74 Vrms (this corresponds to 0.5 mA rms AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the monitor to the owner.

BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)Before returning the receiver to the user, perform the following safety checks: 3. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the chassis and other metal parts in the receiver. 4. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. 5. To be sure that no shock hazard exists, check for leakage current in the following manner. Plug the AC cord directly into a 110-240 volt AC outlet. Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15F capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground. Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor. Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

DVM AC SCALE1.5k ohm 10W

0.15 F TEST PROBE

TO EXPOSED METAL PARTS

CONNECT TO KNOWN EARTH GROUND

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

SAFETY NOTICEMany electrical and mechanical parts in LCD colour television have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by " " and shaded areas in the Replacement Parts List and Schematic Diagrams. /////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards.

i

LC-32D30M-BK/WH/RD PRECAUTIONS FOR USING LEAD-FREE SOLDEREmploying lead-free solder PWBs of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example:

Indicates lead-free solder of tin, silver and copper.

Indicates lead-free solder of tin, silver and copper.

Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.

Soldering As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper. Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing PARTS CODE ZHNDAi123250E ZHNDAi126500E ZHNDAi12801KE PRICE RANK BL BK BM PART DELIVERY J J J DESCRIPTION 0.3mm 250g (1roll) 0.6mm 500g (1roll) 1.0mm 1kg (1roll)

ii

LC-32D30M-BK/WH/RDLC-32D30M-BK/WH/RD

SPECIFICATIONSSPECIFICATIONSModel Item LCD panel Resolution Video Colour System TV Function TV-Standard Receiving Channel VHF/UHF CATV

Service Manual

LC-32D30M-BK/ LC-32D30M-RD/ LC-32D30M-WH 32" (800 mm) Advanced Super View & BLACK TFT LCD 1,049,088 pixels (1366 768)

PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 PAL: B/G, D/K, I SECAM: B/G, D/K, K/K 1 NTSC: M 44.25 863.25 MHz S1 S41ch (including Hyperband) Auto Preset 99 ch NICAM: B/G, I, D/K A2 stereo: B/G 450 cd/m 2 (at AV MODE Dynamic Position) H : 176 V : 176 10W 10 2 4 cm 2pcs DIN type

TV-Tuning System STEREO/BILINGUAL Brightness Viewing angles Audio amplifier Speakers Terminals Rear Antenna input INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 MONITOR OUT RS-232C OSD language Power Requirement Power Consumption Weight without stand with stand

UHF/VHF 75

VIDEO in, AUDIO in, COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz) VIDEO in, AUDIO in, COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz) S-VIDEO in, VIDEO in, AUDIO in HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz), AUDIO in ( 3.5 mm jack) HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz) VIDEO out, AUDIO out 9 pin D-sub male connector English/Simplified Chinese/Traditional Chinese/Arabic AC 110 240 V, 50/60 Hz 133 W (0.7 W Standby) 12.5 kg 14.5 kg 0C 40C

INPUT 6 (PC input) 15 pin mini D-sub, AUDIO in ( 3.5 mm jack)

Operating Temperature

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

iii

LC-32D30M-BK/WH/RD

CHAPTER 1. OPERATION MANUALLC-32D30M-BK/WH/RD

Service Manual

[1] OPERATION MANUAL

PreparationPart namesTV (Front)TV/VIDEO button

Channel up ( )/down (

) buttons

MENU button

Volume up ( )/down ( ) buttons

POWER (On/Off) button

Remote control sensor OPC sensor POWER indicator

OPC indicatorSLEEP timer indicator

The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual operations. The illustrations used throughout this manual are based on LC-32D30M.

11

LC-32D30M-BK/WH/RDPreparation TV (Rear)AC INPUT terminal

INPUT 3 terminals

Headphone jack

INPUT 4 (HDMI) terminals

INPUT 5 (HDMI) terminal

RS-232C terminal

INPUT 6 (PC) terminals

INPUT 1 terminals MONITOR OUTPUT terminals Antenna input terminal INPUT 2 terminals

Regarding the headphone jackUse headphones with a stereo mini plug ( 3.5 mm). Volume display when headphones are plugged in Be sure to unplug headphones from the jack when they are not in use. The speakers do not output volume when headphones are plugged in. The "Audio" menu cannot be operated when headphones are 20 plugged in. You can set the volume to different levels for each input source.

12

LC-32D30M-BK/WH/RDPreparation Remote control unit7 8 VOL /VOL Set the volume. (Mute) Mute the sound. P&P Set the split-screen picture mode. Press P&P again to return to normal view. FREEZE Freeze a motion picture on the screen. EXIT Return to the default screen. WIDE Change the wide image mode. PC Directly select the INPUT 6 terminal. AQUOS LINK buttons If external equipment such as a AQUOS BD Player is connected via HDMI cables and is AQUOS LINK compatible, you can use these AQUOS LINK buttons. (TELETEXT) Select the TELETEXT mode. (all TV image, all TEXT image, TV/TEXT image) (Reveal hidden for TELETEXT) TELETEXT mode: Display hidden characters. (SUBTITLE for TELETEXT) To turn the subtitles on and off. (Hold) TELETEXT mode: Stop updating Teletext pages automatically. Press again to release the hold mode. (Subpage) Display the Teletext subpage directly. (Top/Bottom/Full) TELETEXT mode: Set the area of magnification. 16 TV/VIDEO (INPUT SOURCE) Select an input source. (TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6 (PC)) 17 OPC To switch the Optical Picture Control on and off. 18 AV MODE Select an audio and video setting: AV MODE (STANDARD, MOVIE, GAME, PC, USER, DYNAMIC (FIXED), DYNAMIC), PC MODE (STANDARD, PC, USER). 19 DISPLAY Display the channel or input information. 20 CH /CH TV input mode: Select the channel. TELETEXT mode: Select the page. 21 SLEEP Set the Sleep timer. 22 SELECT To select either screen to be active in split-screen mode. 23 MENU Display the menu screen. 24 / / / (Cursor) Select a desired item on the setting screen. ENTER Execute a command. 25 RETURN MENU mode: Return to the previous menu screen. 26 Colour (Red/Green/Yellow/Blue) TELETEXT mode: Select a page.

1

15

9 10

2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 24 25 26

11 12 13 14

15

1 2 3 4 5 6

POWER (STANDBY/ON) To switch the power on and off. 0 _9 Set the channel. TELETEXT mode: Set the page. (Flashback) Press to return to the previous selected channel or external input mode. IN 4 (HDMI) Directly select the INPUT 4 terminal. IN 5 (HDMI) Directly select the INPUT 5 terminal. MPX Select the sound multiplex mode.

13

LC-32D30M-BK/WH/RD

AppendixMounting the TV on the wallRemoving the standFor wall mounting with the optional bracket, remove the stand. Before detaching/attaching the stand

Before detaching (or attaching) the stand, unplug the AC cord from the AC outlet. Remove all terminal covers and connected cables. Lay the TV down on cushioning (such as a blanket) over a table. Make sure two or more people perform the operation.

CAUTION Do not remove the stand from the TV unless using an optional bracket to mount it.

1

2

3

Press the two hooks and take the hinge's cover off.

Unfasten the four screws used to secure the stand in place.

Detach the stand from the TV. (Hold the stand so it will not drop from the edge of the base area.)

NOTE To attach the stand, perform the above steps in reverse order.

Handling and precautions with the wall-mounted TVYou can mount the TV on the wall using the optional 37-AAG5 bracket. For details, refer to the instructions supplied with the optional bracket.CAUTION This TV should be mounted on the wall only with the 37-AAG5 (SHARP) wall mount bracket. The use of other wall mount brackets may result in an unstable installation and may cause serious injuries. Installing the Liquid Crystal Television requires special skill that should only be performed by qualified service personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.

Using an optional bracket to mount the TV

You can ask a qualified service personnel about using an optional 37-AAG5 bracket to mount the TV to the wall. Carefully read the instructions that come with the bracket before beginning work.

Hanging on the wall 37-AAG5 wall mount bracket. (See the bracket instructions for details.)

About setting the TV angle

Vertical mounting

Angular mounting

37-AAG5

NOTE Detach the cable clamps on the rear of the TV when using the optional mount bracket. To use this TV mounted on a wall, first remove the cover at the 4 locations on the rear of the TV, and then use the screws supplied with the wall mount bracket to secure the bracket to the rear of the TV.

14

LC-32D30M-BK/WH/RD

CHAPTER 2. DIMENSIONSLC-32D30M-BK/WH/RD

Service Manual

[1] DIMENSIONS306.7

Unit: mm

410 785.4 74.8 108.6 95.1

699.3

543.6

393.85

607

363

240.9 200

200 110

21

LC-32D30M-BK/WH/RD

Service CHAPTER 3. REMOVING OF MAJOR PARTSLC-32D30M-BK/WH/RD

Manual

[1] REMOVING OF MAJOR PARTS1. Remove the 3 Boss Caps [1]. 2. Remove the Stand Hinge Cover [2]. 3. Remove the 4 lock screws [3] and detach the Stand. 4. Remove the 2 lock screws [4], 2 lock screws [5], 9 lock screws [6] and detach the Rear Cabinet.

Rear Cabinet 6 Front Cabinet

Boss Cap 1

5 4

2 Stand Hinge Cover 3

Stand

31

LC-32D30M-BK/WH/RD5. Remove the 3 lock screws [7], 8 lock screws [8] and detach the Stand Angle.

Stand Angle

8

7

32

LC-32D30M-BK/WH/RD6. Disconnect all connectors from all the PWBs [9]. 7. Remove the Speaker-L/R [10]. 8. Remove the 2 lock screws [11] and detach the R/C, LED Unit. 9. Remove the Top Cover Ass'y [12]. Remove the 1 lock screw [13] and detach the KEY Unit from the Top Cover. 10.Remove the 2 lock screws [14] and detach the Mini AV Unit Ass'y. 11.Remove the 2 lock screws [15] and detach the Mini AV Cover, Mini AV Unit from the Mini AV Angle.

12 Power Button 9 15KM

Top Cover Operation Button 13

KEY Unit 9VD

14LB FFC FFC LB PD

Mini AV Unit Mini AV Cover Mini AV Angle

9

VD

KM

9

SP RA

PD

9 R/C, LED Unit 11

RA

10 Speaker-R

Speaker-L

10

33

LC-32D30M-BK/WH/RD12.Remove the 4 lock screws [16], 2 lock screws [17] and detach the MAIN Unit. 13.Remove the 4 lock screws [18] and detach the INVERTER/POWER Unit.

17

16

MAIN Unit INVERTER/POWER Unit

18

34

LC-32D30M-BK/WH/RD14.Remove the 2 lock screws [19], 2 lock screws [20], 8 lock screws [21] and detach the Center Angle-L/R. 15.Remove the 4 lock screws [22] and detach the LCD Angle-A/B. 16.Detach the LCD Panel Module.

20 21 Center Angle-R 19

20 21 Center Angle-L 19

22

22

LCD Angle-A

LCD Angle-B

LCD Angle-B

LCD Angle-A

22

22

35

LC-32D30M-BK/WH/RD

CHAPTER 4. ADJUSTMENTLC-32D30M-BK/WH/RD

Service Manual

[1] ADJUSTMENT PROCEDUREThe adjustment values are set to their optimum at the factory before shipping. If by any chance a value should become improper or a readjustment is required due to part replacement, make an adjustment according to the following procedure. Before adjustment, perform aging for approx. 60 minutes to stabilize the unit.

1. Entering the adjustment process modeThere are 3 ways as follows: After power-on, press ADJUSTMENT PROCESS key of the remote control. With the KEY 4 (pin E1 of IC801) set to L, turn the power ON. During servicing While holding down the TV/VIDEO and Volume DOWN keys at the same time, set the Power switch to ON. (K standing for inspection process mode is displayed in the upper left portion of the screen.) ment process mode screen appears.) Press the Channel DOWN and Volume DOWN keys at the same time. (The adjust-

To cancel it, turn off the power using the Power switch or remote control.

2. Key operation in the adjustment process mode1. Basic operations Tune in to a station using the Channel UP/DOWN keys. Switch the input using the TV/VIDEO key. Select an item to adjust using the Cursor page, and pressing the Cursor / keys. (Pressing the Cursor key while at the bottom item moves to the top item on the next

key while at the top item moves to the bottom item on the previous page.) / keys.

Adjust the item selected using the Volume +/ or Cursor

Press the Menu key to move to the next item. (Pressing the Menu key while at the bottom item moves to the top item on the next page.) Pressing the ENTER key while at an item other than I2C DATA and HOTEL POWERFIX on page 2 moves to the setting page of that item name. Press the Flashback key to exit each setting page.

2. Layer movement

3. Adjustment procedure for RGTAR, GGTAR and BGTAR items on pages 3, 4, and 5 of the DVP layer At RGTAR, GGTAR, and BGTAR on pages 3, 4, and 5; pressing the Volume UP/DOWN or the Cursor / keys moves left or right.

Select an item to adjust, and press the ENTER key. As the Cursor moves to the corresponding right field, make adjustments using the Volume UP/DOWN or the Cursor ENTER key at the right field moves back. Pressing the Cursor / keys, the Menu key, etc. moves to a different item. / keys. Pressing the

3. Initialization3.1. Pull down the pin E1 & F3 of IC2001 to GND, then turn on the power. 3.2. Check MODEL (A654MA). 3.3. Inch Size Setting1. Enter Adjustment process Mode 2. Press volume down and channel up simultaneously. This will bring cursor ' ' to 'INCH SIZE'.

3. To set inch size '32', press '1' on remote control. This will change 'INCH SIZE' to purple colour for 25sec. 4. Cursor ' ' then will go up to 'MODEL'. If yellow highlight is still remain at 'INCH SIZE', process inch size setting is NG. Check the hardware inch size selection.

41

LC-32D30M-BK/WH/RD(Screen of adjustment process menu page 1)

0 1 2 3 4 5 6 7 8 9 10 11 12 13

0 1 2 3 4 1 M O D I E P E P N E N R U X O O R C R B T W R R

5 E

6 L

7

8

9

10 11 12 13 14 15 16 17 18 18 20 21 22 23 24 25 26 A H 6 0 5 0 4 4 M 3 F F A 0 2 0 F F 0 1

B H O R L I C E R M A O R 1) I Z N O C M O N T O N L S S T 0 0 H 4) 0 0 H S E O R T A 0 0 R D O E A N M 5) M E E L R N D S E

8 T

8

6

A

O O R D B 2) O B Y 0 0 0 0 R Y C H H C C A 0 0 A A U M M U U S S S E 3) E E 0 0

H

0

M

4. Adjusting the LCD panelWhen replacing the LCD control PCB, follow these steps to adjust VCOM. 1. Enter the adjustment process mode. 2. Select the item [VCOM ADJ] using the Cursor ( / / / ) or CH ( / ) keys on the remote controller.

3. Press the ENTER key to check that the adjustment pattern is displayed. 4. Adjust the flicker in the middle of the screen to minimum using the Cursor ( 5. Press the ENTER key to turn off the pattern. 6. To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.) CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode.If the settings are tampered in this mode, unrecoverable system damage may result. / ) or CH ( / ) or VOL (+)/(-) keys on the remote controller.

42

LC-32D30M-BK/WH/RD5. Adjustment5.1. AD converter level adjustment1. 1080i input Adjustment Conditions 1) 1080i 75% colour bar signal input Used device name: LEADER LT448 Signal name: COLOUR BAR * Use the LT-446-compatible third one of three colour bars. Setting value: 02: 1080i/59.94 (30 sF) H: 33.72 kHz, V: 29.97 Hz Adjustment Procedure 1) Set AUTO GAIN-OFFSET on page 3 (M2-HD) of the adjustment process DVP hierarchy to ON.

2. 480i input Adjustment Conditions 1) 480i 75% colour bar signal input Used device name: LEADER LT448 Signal name: COLOUR BAR * Use the LT-446-compatible third one of three colour bars. Setting value: 15: 480i/60 H: 15.73 kHz, V: 29.97 Hz Adjustment Procedure 1) Set AUTO GAIN-OFFSET on page 4 (M2-SD) of the adjustment process DVP hierarchy to ON.

3. PC XGA input Adjustment Conditions 1) XGA 75% colour bar signal input (RGB) Used device name: LEADER LT448 Signal name: COLOUR BAR SATURATION 75% * Use one of two colour bars where SATURATION can be changed. Setting value: 28: XGA H: 48.36 kHz, V: 60.00 Hz Be sure to set the SYNC setting to OFF. Adjustment Procedure 1) Set AUTO GAIN-OFFSET on page 5 (M2-PC) of the adjustment process DVP hierarchy to ON.

*

If all the items are set to ON, RUN is displayed during adjustment.

43

LC-32D30M-BK/WH/RD5.2. TAMP adjustmentAdjustment Conditions 1) Receive the PAL standard colour bar signal. Adjustment Procedure 1) If the maximum value of PAL TAMP1 on page 1 of adjustment process DVP hierarchy is not in the range of values in the list below, adjust PAL TAMP1 on the same page so that the maximum value of Y is in the range of values in the list below. * Note that the setting value may vary by model. 2) When pressing the TAMP1 direct keys, adjustment of PAL TAMP1 is complete. Then, The values of NTSC TAMP1 and SECAM TAMP1 are automatically set. (NTSC: Value of PAL 7, SECAM: The same value as PAL)

MODEL Setting value Reference

LC-32D30M 101 ~ 105

(Screen of page 1 of adjustment process menu DVP)

44

LC-32D30M-BK/WH/RD5.3. White balance adjustment1. Place the luminance meter at the centre of the LCD screen 2. Set the LCD TV as below. AV MODE Backlight Aging Time 3. Adjustment Test Signal [ Input Signal ] [ Adjust Value ] Display the WB built in test signal of RGB1 & RGB2 on the screen by using the remote control code.(Key1 for RGB1, Key2 for RGB2) Page 2-2 of adjustment process menu DVP : RGB 1 , RGB 2 : : : [STANDARD] +16(MAX) Minimum 60 minutes

Teaching set send by engineering dept is set as reference 4. Reference values for adjustment reference ( Equipment : Luminance meter [Minolta CA-210] ) RGB1 x = 0.261 y = 0.277 x = 0.261 y = 0.277 Adjustment spec 0.004 0.004 0.004 0.004 Inspection spec 0.01 0.01 0.01 0.01 radius from the center point radius from the center point radius from the center point radius from the center point

RGB2

*Initial value at RGB1 point : 800 ( G1 is fixed to 800 ) *Initial value at RGB2 point : 160 ( G2 is fixed to 160 ) Ref. : For inspection, set the LCD TV as below. AV MODE Backlight Aging Time : : : [DYNAMIC] +16(MAX) Minimum 60 minutes

45

LC-32D30M-BK/WH/RD5.4. STANDBY CAUSE FUNCTIONSThis model is equipped with a STANDBY CAUSE FUNCTIONS which stores the cause of why the unit is turned off and displays it on adjustment process mode. 1. NORMAL STANDBY CAUSE ERROR CODE here indicates cause of standby in normal operation or Function of the Unit. No display when the unit is turned off with R/C. Only the latest cause is indicated. 2. ERROR STANDBY CAUSE ERROR CODE here indicates cause of Error in the unit. It also indicates accumulated operating times of the unit. The last five histories are displayed. 1)-5) five histories 5) is the latest. When there is no error, error code is 0 and no characters appear. 3. POWER ON ERROR CAUSE ERROR CODE here indicates cause of Error when power on the unit. When there is no error, error code is 0. NORMAL STANDBY CAUSE Display Code 1 3 4 5 6 7 8 Description in the cause of Main Power switch off in the cause of no signal off in the cause of no operation off in the cause of Power management (Mode 1) off in the cause of Power management (Mode 2) off in the cause of SLEEP timer in the cause of off by CEC

ERROR STANDBY CAUSE Display Code 3 Description in the cause of abnormal temperature

POWER ON ERROR CAUSE Display Code 12 13 30 31 32 40 41 42 Description DVP15 IN Terminal Error Power IN Terminal Error TASS Error Audio Multiplex Decoder Error TAS-FIRM-DONE Terminal Error Tuner Error AV SW IC Error HDMI IC Error

46

LC-32D30M-BK/WH/RD6. MCL setting procedure1. MCL is displayed in the upper left portion of the screen as shown in the figure below by sending the MCL key of the remote control for adjustment.

2. When the screen disappears after a few seconds and appears again, MCL setting is completed.

7. Factory setting7.1. Performing the factory setting using the remote control for adjustment1. Perform the factory setting using the remote control for adjustment. (This setting must be done after the MCL data setting.) 2. M stands for factory setting 2, X stands for factory setting 4 is displayed in the upper left portion of the screen by continuing to press the Factory Setting key on the remote control for adjustment. (The figure below is the screen for factory setting 4.)

3. When SETTING COMPLETE is displayed in the middle of the screen after a few seconds, setting is completed.

Model name LC-32D30M 4. Turn off the power.

Key name Factory setting 2

Remote control code 100000001010110

Setting S-SYSTEM B/G

Set OSD language ENGLISH

NOTE: Set the Power switch to OFF immediately after completing the factory setting. CAUTION: Do not plug on again after shipment setting is done. If do, please re-do the shipment setting. Do not power off with remote control.

47

LC-32D30M-BK/WH/RD

[2] PUBLIC MODE SETTING PROCEDURE1. How to start Public Mode There are the following two ways to get the public mode setup screen displayed.

1) Press the INPUT and VOL (+) keys on the set at once and turn on the power. 2) Get the password input screen displayed. Procedure The input starts with the leftmost digit. Use the numeric keys [1] thru [9] and [10/0] keys on the remote controller. The other keys are not acceptable. With a numeric-key input, will change to . The input position will move one digit to the right. With all the 3 digits entered, the password will be verified.

3) The 3-digit password is now verified. The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.) With any other passwords, the screen changes to the normal mode.

In the adjustment process mode, turn on PUBLIC MODE. Also press the CH (

) and VOL (+) keys on the set at once and turn on the power.

2. How to exit Public ModeThere are the following ways to quit the public mode setup screen. Turn off PUBLIC MODE in the adjustment process mode. ( itself. Turn off the power with the POWER key. ( Select ENTER. ( ) ) ) ) This way alone is not for quitting the setup screen, but for quitting the mode

Move the cursor to RESET and press the FLASHBACK key. (Back to the normal mode screen) (

PUBLIC MODE stays on in the adjustment process mode. The settings will be back to the factory ones.

3. Public Mode Setting Values With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.)

48

LC-32D30M-BK/WH/RD4. Public Mode MenuThe guidance is not displayed onscreen. Setup procedure To move the cursor up and down, use the cursor UP/DOWN key (remote controller) and CH ( )/( ) key (remote controller and set).

To change the settings, use the cursor RIGHT/LEFT key (remote controller) and VOL (+)/() key (remote controller and set). To save new settings, keep the cursor at Enter and use the cursor RIGHT/LEFT key (remote controller) and VOL (+)/() key (remote controller and set). Public mode Power on fixed Maximum volume Volume fixed Volume fixed level RC button Panel button Menu button On screen display Input mode start Input mode fixed 232C Powon RC path through Reset Enter [Variable ] [ 60] [Variable ] [ 20] [Respond ] [Respond ] [Respond ] [Yes ] [Normal ] [Variable ] [Disable ] [Off ]

5. On Setting Items1. POWER ON FIXED Selection Default Explanation Variable/Fixed Variable When set to Fixed, the power cannot be turned off with the power key on the remote control or main unit, and the image reception state is kept (it does not enter the standby state). The power can be turned off by shutting off power supply from AC. Power key on the main unit/remote control power supply key OFF timer/ON timer None Selection of FIXED assumes use of STB, etc. When set to Variable, if the main power switch is set to off, the power is turned off after a wait of 1 second. (Push-push switch only) Display ON/OFF in the hotel menu is controlled by the adjustment process HOTEL POWERFIX. When the power button is operated, a caution is displayed (it times out in 5 seconds). (For the caution, refer to the power on fixed message sheet.) * The caution is not displayed when in the adjustment process, hotel menu, default setting, MCL operation and auto preset (Ch search operation). The OSD display including the menu and this caution have priority over all others. When OSD display (described below) is set to Variable, this caution is displayed as a special case.

Limit in setting Exception Remarks

2. MAXIMUM VOLUME Selection Default Explanation Limit in setting Exception Remarks Adjustment from 1 to 60 (no loop) 60 Sound volume can not be adjusted higher than the preset value. When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed. The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value. In the item VOLUME of adjustment process, the sound volume can be set freely irrespective of this setting. Setting is valid only for the speakers of the unit. (As for the headphone, the sound volume can be set up to 60 irrespective of the limit.) In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value. When the sound volume is set higher than the MAX setting by the adjusting process or headphone, the sound volume control operation is prohibited for turn-up and the sound volume should be turned down to MAX in this state.

49

LC-32D30M-BK/WH/RD3. VOLUME FIXED Selection Default Explanation Limit in setting Selection between Variable and Fixed (loop provided) Variable Sound volume is fixed and made invariable. The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made impossible. (Basically, the menu is not displayed.) The following keys become invalid: 1) Sound volume Up/Down (VOL +/-) [for both remote control and the unit] 2) Mute (MUTE) In the item VOLUME of adjustment process, the sound volume can be set freely irrespective of this setting. In Variable setting, the sound volume had been conventionally set at 1 but this operation has been abolished (and follows the last memory). The sound volume for the ON-time is not set at 1 either and the sound volume set value of the ON-timer before executing the hotel mode is held. Setting is valid only for the speakers of the unit. (As for the headphone, the sound volume can be set up to 60 irrespective of the limit.) In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value. As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority. Once the sound volume has been changed by adjustment process or headphone, it should be set back to the sound volume preset by sound volume fixing level when the adjustment process ends or when the headphone is removed.

Exception Remarks

4. VOLUME FIXED LEVEL Selection Default Explanation Limit in setting Exception Remarks 5. R/C BUTTON Selection Default Explanation Limit in setting Selection between Respond, Limited and No respond (loop provide) Respond Keys acceptable by remote control are limited or reception of keys can be prohibited. 1) In limited setting, only power ON/OFF, sound volume , tuning and BACKLIGHT (brightness sensor) are accepted. 2) In No respond setting, all the keys (including the power key) are not accepted. Adjustment process, factory setting, inspection process and hotel only keys are valid irrespective of setting. All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting. Adjustment from 1 to 60 (no loop) 20 The sound volume to be fixed by Volume fixed is determined. None None Setting is valid only when Volume fixed is selected for fixed. This must be confirmed actually by changing also the sound volume in accordance with setting.

Exception Remarks 6. PANEL BUTTON Selection Default Explanation Limit in setting Exception Remarks 7. MENU BUTTON Selection Default Explanation Limit in setting

Selection between Respond and No respond (loop provide) Respond All the operations by keys (except the power key) of the unit can be invalidated. Inspection mode and hotel menu mode can be started irrespective of setting. All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.

Exception Remarks

Selection between Respond and No respond (loop provide) Respond In No respond setting, the menu operation by the menu key of the remote control and the menu key of the unit are invalidated. ON-timer (Wakeup Timer) is turned OFF. The following keys become invalid. Wake-up timer and clock setting keys and all of the direct change keys to menu display Inspection mode and hotel menu mode can be started irrespective of setting. All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.

4 10

LC-32D30M-BK/WH/RD8. ON SCREEN DISPLAY Selection Default Explanation Limit in setting Selection between Yes, Limited (loop provide) Yes The following OSD displays are made ineffective. Displays of menu group, channel call, sound volume bar and direct key call Set time of the OFF-timer (SLEEP TIMER) is cleared. Setting of the no-signal power-OFF (AUTO POWER OFF) is cleared to OFF. Setting of the no-operation power-OFF is cleared to OFF. Keys falling under any of the following items become invalid. 1) Appearance of screen changes and the sound changes. 2) Personal functions which are hard to restore. Ex.) Screen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis, AUDIO ONLY, sound changeover, LANGUAGE, CLOSED CAPTION Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for change by customer are not prohibited. Ex.) Brightness sensor (BACKLIGHT) and PIC. FLIP Such a caution which is displayed independently is displayed as it is. Non-responding signal caution, TELETEXT caution and power-ON fixing caution

Others

Exception

9. INPUT MODE START Selection Default Explanation About options Selection between Normal, TV (CH~) INPUT1~5, PC (loop provide) Normal In power-ON, the input source to be started or channel can be set. (In standard mode, the operation follows the last memory.) All the input sources in the model are made selectable. When the input/output switchable input source is selected and the input source is set to output, the setting of input/output switching is changed to input at the execution of hotel menu. In addition, the input/output switching by menu is prohibited. In TV mode, the display of all channels is stopped and it is treated as an input source. At this time, the channel to be set follows the last memory and the content of the last memory is included in the notation by options. Ex.) TV (CH2), TV (CH4) etc. The order of appearance of options in the hotel menu should agree with the order of toggles by input switching key. The display of channel setting menu and the channel setting operation are prohibited (except for MCL). None In setting at Normal, the setting of Input mode fixed is changed to Variable and selection should be prohibited.


10.INPUT MODE FIXED Selection Default Explanation Limit in setting Selection between Variable and Fixed (loop provide) (Variable) The input mode is fixed at the input source or the channel set at the Input mode start in 9 and other input sources and channels can be made non-selectable. With the execution of hotel mode, the input source is forced to change to that set by Input mode start and the channel switching and input switching are prohibited thereafter. The following keys are invalidated. CH , direct tuning button, FLASHBACK, input *However, the keys (input switching and CH keys) of the unit for menu operation remain valid. None In the following case, setting is cancelled and mode is changed to Variable. When the setting of Input mode start is set to Standard (Normal) 11.232C POWON Selection Default Explanation Limit in setting Exception Remarks Enable and Disable Disable When in the standby state, power ON by the RS-232C command is enabled or disabled. None None It is irrelevant to power OFF by the RS-232C command.

Exception Remarks

4 11

LC-32D30M-BK/WH/RD12.RC PATH THROUGH Selection Default Explanation Off, On: TV RCE, On: TV RCD Off Remote control signal output from the pin 9 of the RS-232C terminal and signal reception by is enabled or disabled. When set to ON: TV RCE, TV also receives signals. With ON: TV RCD, the remote control signal is output from the pin 9, but TV does not respond to the remote control. When set to ON: TV RCD, TV does not accept the remote control. None RS-232C power ON command POWR1_ _ _


4 12

LC-32D30M-BK/WH/RDMEMO

4 13

LC-32D30M-BK/WH/RD

Service CHAPTER 5. TROUBLESHOOTING TABLELC-32D30M-BK/WH/RD

Manual

[1] TROUBLESHOOTING TABLENo power (front LED failure to light up) or no startup (front LED failure to turn from red to green)

Is the AC cord connector tightly connected to the set?

NO

Reconnect the AC cord tightly and turn on the power again.

YES Is the output voltage at pin (5) of P2801 (BU+5V line) as specified?

NO

Replace the power unit 32 inch (RUNTKA419WJQZ)

YES Are the wire harnesses and other cables properly connected in the set?

NO

Reconnect the wire harnesses and other cables properly in the set.

YES Is there the PS ON and signal input at pin (10) of P2801 (PS ON line)?

NO

Check the PS ON signal line.

YES Is the output voltage of each pin on P2801 as prescribed? Pin 1, 2, 3 and 4 13V Pins 11 5V YES Are the DC/DC converter outputs and the output voltages along the control lines as specified? 1) 2) 3) 4) 5V (IC2803 etc.) 4V (IC2804 etc.) 3.3V (IC2804 etc.) 9V (IC2801 etc.)

NO

Replace the power unit 32 inch (RUNTKA419WJQZ)

NO

Check the DC/DC converters and the control lines. Replace defective parts as required.

51

LC-32D30M-BK/WH/RDWith signal input No video on screen (1)

No external input video on screen

Is INPUT 1 selected on the input select menu screen?

NO

Select INPUT 1 on the input select menu screen to pick up the right input signal.

YES Is there the video signal input at pin (6) of IC3409 (AV SWITCH)?

NO

Check the line between pin (12) of J3404 and pin (6) of IC3409.

YES Is there the video signal output at pin (16) of IC3409?

NO

Check IC3409 and its peripheral circuits.

YES Is there the video signal input at U2 pin of IC801?

NO

Check its peripheral circuits.

YES Are signals output from the pins P22, P23, R22, R23, T22, T23, U22, U23, V22, V23, W22 and W23 of IC801 normally?

NO


YES Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits.

52




NO



NO


YES Is there the video signal output at pin (16) of IC3409?

NO


YES Is there the video signal input at U2 pin of IC801?

NO



NO



53




NO


YES Are there the Y, Pb and Pr signal inputs at pins (34), (32) and (30) of IC3409, respectively?

NO

Check the line between pins (7)/(8)/(9) of J3404 and pins (34)/ (32)/(30) of IC3409.

YES Is input waveform of IC801 normal? Y=U1pin, Sync=J2pin Pb=L1pin, Pr=R1pin YES Are there the signal outputs at pins U22, U23, V22, V23, W22, W23, P22, P23, R22, R23, T22, T23 of IC801, respectively?

NO


NO



With signal input

No video on screen (4)



NO


YES Are there the Y, Pb and Pr signal inputs at pins (40), (38) and (36) of IC3409, respectively?

NO

Check the line between pins (7)/(8)/(9) of J3403 and pins (40)/ (38)/(36) of IC3409.

YES Is input waveform of IC801 normal? Y=U1pin, Sync=J2pin Pb=L1pin, Pr=R1pin YES Are there the signal outputs at pins U22, U23, V22, V23, W22, W23, P22, P23, R22, R23, T22, T23 of IC801, respectively?

NO


NO



54




NO



NO


YES Is there the video signal output at pin (16) of IC3409? Are there the Y and C signal outputs at pins (24) and (26) of IC3409, respectively? YES Is there the video signal input at U2 pin of IC801? Are there the Y and C signal inputs at P1 pin and K1 pin of IC801, respectively?

NO


NO

Check its peripheral circuits. Check its peripheral circuits for the C signal, and its peripheral circuits for the Y signal.


NO



55


No external input video on screen ,

Is INPUT 4, INPUT 5 selected on the input select menu screen?

NO

Select INPUT 4 or INPUT 5 on the input select menu screen to pick up the right input signal.

YES Are there the signal inputs from the HDMI (SC404, SC403) connector to the following input terminals of IC8702 (pin (16), (17), (19), (20), (22), (23), (25), (26), (31), (32)).

NO

With an HDMI device connected, is IC406, IC404 (EEPROM) accessed by I2C and is the DDC I2C CLOCK/DATA data read?

NO Check IC406, IC404 and their peripheral circuits. YES Are there the clock, H, V, Data signal outputs at pins (71) - (80), (83) - (92), (96), (98), (99), (104) - (113) of IC8702, respectively? YES Are waveforms of the clock, H, V, and Data terminals of IC801 normal? YES Are there the signal outputs at pins U22, U23, V22, V23, W22, W23, P22, P23, R22, R23, T22, T23 of IC801, respectively? YES Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits. NO Check IC8702 and their peripheral circuits.

NO


NO


No video on screen (7)

No video in the UHF/VHF reception

Is the IF output from the tuner (TU3402) as specified?

NO

Check TU3402 and its peripheral circuits.

YES Is there the video signal input at pin (14) of IC3409 (AV SWITCH)? YES Is there the video signal output at pin (16) of IC3409?

NO

Check the line between TU3402 and IC3409.

NO


YES is there the video signal input at U2 pin of IC801?

NO



NO



56

LC-32D30M-BK/WH/RDNo audio heard (1)

No sound in the UHF/VHF reception.

Is the IF output from the tuner pin (14) of TU3402 as specified?

NO

Check TU3402 and its peripheral circuits.

YES Is the SIF signal input at A21 pin of IC801 as specified?

NO

Check Q3414, Q3415 and their peripheral circuits.

YES Are audio signals from the pins B23 and D23 of IC801 as prescribed?

NO

Check IC801 and their peripheral circuits.

YES Is there the L-ch audio signal output at pins (51) of IC3602? Is there the R-ch audio signal output at pins (52) of IC3602?

NO


YES Is there the L-ch audio signal output at pins (39), (44) of IC1301 (AMP)? Is there the R-ch audio signal output at pins (17), (20) of IC1301 (AMP)? YES Are audio signals of L-ch and R-ch output from the pins (1)/(2) and (3)/(4) of P1301 normally? YES Check the speakers and their peripheral circuits.

NO


57


No external audio heard Is there the L-ch audio signal input from pin (11) of input terminal J3403 to pin (43) of IC3602? Is there the R-ch audio signal input from pin (10) of input terminal J3403 to pin (44) of IC3602? Is there the L-ch audio signal input from pin (11) of input terminal J3404 to pin (46) of IC3602? Is there the R-ch audio signal input from pin (10) of input terminal J3404 to pin (47) of IC3602? Is there the L-ch audio signal input from pin (5) of input terminal J9901 to pin (63) of IC3602? Is there the R-ch audio signal input from pin (4) of input terminal J9901 to pin (64) of IC3602? YES Is there the L-ch audio signal output at pins (39), (44) of IC1301 (AMP)? Is there the R-ch audio signal output at pins (17), (20) of IC1301 (AMP)? YES Are audio signals of L-ch and R-ch output from the pins (1)/(2) and (3)/(4) of P1301 normally? YES Check the speakers and their peripheral circuits.

NO


NO


58


No audio signal at the monitor audio output terminal.

Is there the L-ch audio signal output at pin (86) of IC3602? Is there the R-ch audio signal output at pin (87) of IC3602?

NO


YES Does the audio mute circuit function? (Q3401, Q3402 and Q3417)

NO

Check Q3401, Q3402, Q3403 and their peripheral circuits.

YES Check the monitor audio output terminal (J3402) and its peripheral circuits.

No audio heard (4)

No sound heard from the headphone.

Is there the audio signal output at pins (91) (L-ch) and (93) (R-ch) of IC3602?

Is there the L-ch audio signal output at pin (1) of IC3604 (H/P AMP)? Is there the R-ch audio signal output at pin (7) of IC3604 (H/P AMP)? YES Check J9802 and it peripheral circuits, as well as the headphone jack line.

NO

Is the mute signal input at pin (2) of IC3604 as specified?

59


No HDMI sound heard. (INPUT 4, INPUT 5 *INPUT 5 is digital audio.)

Does the HDMI image appear on screen?

NO

Refer to in No external image on screen (HDMI).

YES No audio output from INPUT 4 and INPUT 5.

NO

Check if the EDID data of IC406 (INPUT 5) or IC404 (INPUT 4) is normal.

YES Check peripheral circuits of IC406 and IC404.

YES Are waveforms of the pins (120) - (124) of IC8702 output normally?

NO

Check peripheral circuits of IC8702.

YES Are output waveforms of the audio output pins B23 and D23 of IC801 normal?

NO


YES Are audio signals of L-ch and R-ch input in to the pins (46) and (47) for volume, equalizer and sound of IC3602 normally and output from the pins (84) and (85) normally? YES Are there the L-ch and R-ch audio signal outputs at pins (39), (44) and (17), (20) of IC1301 (AMP), respectively?

NO


NO


YES Are there the L-ch and R-ch audio signal inputs at pins (1), (2) and (3), (4) of P1301, respectively?

5 10


No sound from the HDMI sound input terminal. (INPUT 4 analog audio) YES Is there the L-ch audio signal input from pin (2) of external input terminal J404 (HDMI AUDIO IN) to pin (57) of IC3602? Is there the R-ch audio signal input from pin (3) of external input terminal J404 (HDMI AUDIO IN) to pin (58) of IC3602? YES Are there the L-ch and R-ch audio signal outputs at pins (84) and (85) of IC3602, respectively?

NO


YES Are there the L-ch and R-ch audio signal outputs at pins (39), (44) and (17), (20) of IC1301 (AMP), respectively?

NO



No audio heard (7)

No PC audio output YES Pin (2) of J405: Is L-ch input into the pin (60) of IC3602? Pin (3) of J405: Is R-ch input into the pin (61) of IC3602? YES Are there the L-ch and R-ch audio signal outputs at pins (84) and (85) of IC3602, respectively?

NO


YES Are there the L-ch and R-ch audio signal outputs at pins (39), (44) and (17), (20) of IC1301 (AMP), respectively?

NO



5 11

LC-32D30M-BK/WH/RD

CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAMLC-32D30M-BK/WH/RD

Service Manual

[1] OVERALL WIRING DIAGRAM

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

61

LC-32D30M-BK/WH/RD

[2] SYSTEM BLOCK DIAGRAM

I

HGradation IC

G

F

E

DMUTE Circuit

Inch Size Select Circuit

CMUTE Circuit

MUTE Circuit Rewriting Connector

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

62

LC-32D30M-BK/WH/RD

CHAPTER 7. PRINTED WIRING BOARD ASSEMBLIESLC-32D30M-BK/WH/RD

Service Manual

[1] MAIN Unit

I

H

G

F

E

D

C

B

A

MAIN Unit (Side-A)1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

71

I

F

E

G

A H

B

C

D

LC-32D30M-BK/WH/RD

1P5205 LUG3401 R5210 R5211 C5208 R5214 R5204 R5205 R5201 R5203

R5212

R460

R3406 R3421

R459

R461

D5208

C5205

C5206Q5201

Q5202

Q5203

LUG3406

C3502 C3503

R5207 C5211 R5209

D5201

R5215

MAIN Unit (Side-A Chip)R5206 R5208 R5216 D1903 D1902 FB1901 TH802 D1904

2J406R3563 R3430 C3419

Q3402C3504 Q3401

R458 FB1902D1905

SC1901

R457 C423R3483 D1907

R3401

R3490R3491 C3495

R3422

R1931 R1930 C1912 C1914 C1915

3Q3416D1906

R1913 R441 R443

C3505R3408

P2002 R3562

R3418 R1917R3492 C1909

C1913

Q1905

R3429 C3501 C3418R3498 C3483 R3484 IC1904 IC1903

R1919 C1910 C1911

R3405 R3489 Q3411 D3402 D1908 FB1903 R1924

R1923

J404

J3401

R3485 C3493 R3486 Q1906

4Q1907R3407

C3401 R3402 R1904 R1909

R1907Q1904

R1910

R3417 R1912

C1505

Q1903

R1905

R3497 IC1902

IC1502

IC1503

C1504

D1502

R1522

C1503

IC1901

C1502

D3413

R3473 C3489 R3475 R1906 R1908 R3476 R3431 D3412 C3417 R3456 R1911 D3411

Q3409

R3477

D3414

R3474

R1519 R1521

Q1902

R3435

R3426 R3414

5Q3405

J405

R3425 R3412R3459

SC404

R3454

D3410R3472 R3470 Q3404 R3453 R3455

R437 R439

R3415 R3432 D3409 R3423

C3415

6R3427 R3413 D3407 D3408R3471

C3487 R3467 R3469 R3468

VA422VA421 VA418VA417 VA424VA423 VA420VA419

L410

L413

L412

L411

Q3408

R416 R417 C403

R401

D3423 D3404 D3403D3415 R3480

D3422 D3406 D3405R3409

R406 D401

D416 FB403 FB404 D414

D3401

D408 R402 SC403

R3478

7R3481 C3455 C3485 R3410 R3403 R3447 R3437 R3449 R3450R3465 R3428 R3463

C3491 R3479

C3413 R3446 R3411 R3448

R3444

SC401

R405 D402

Q3403

R3464 C3500

R3482

Q3410 Q3406 C3484 R3424R3466 R3461 C3427 C3425 R3457 Q3407 R3462 C3426 R3458 C3424 R3451

R408 R407 FB401 D415 R3452 R3493R3494 R3495 R409

D409R404 VA414VA413 VA410VA409 VA416VA415 VA412VA411

L406

L409

L408

L407

C402

R3442 C3412

8R8609 R8616

D403

IC401

R465

D410SC402

R926 Q808

R8608

P8603

C919

C806 R925 R933 R913

C920

9 10TU3402

Q806

VA406VA405 VA402VA401 VA408VA407 VA404VA403

C801 R903

R935 R921 C803 R922

R911

L403

L414

L405

L404

R912 C918 R923

Q807

C917

P8602 R8603 R8604 C8601R8613

IC1507

R1524

R8605

R1512

11C8730 C8729

R1575

FB8701 C8704 C8724

LUG3404

LUG3402

C8711

R8761

Q8709 R8768

7212C3670 C3669

R8760 R8702

R8703

R3593 C3473

R3554 R3550

R3555

IC8702

R3544

C8726

C3463

R8720

C3476

C3478

C3474 L3405

R3529

Q3413

R8706

R8733 C8723 C8727R8732 R8747 R8735R8737R8736 X8701Q8705

D5205

C5230 R5245

D5206C811

P5204

Q8704

13 14 15 16 17 18 19 20 21 22

R3650

R3651

C3665 C3664 C3666

C3603

C3604

R3434 R3603

C3466

C3469

C8725 R8746

R8730

R8744

R8743

R8742

R8727

R8707

C5229

R8739 R8710

R5244

R3488

R3433

R8745

D5207

C5228

IC808

R3606 C3606

IC3601

IC3604

R3610 R3607

C899

R879

C3687 C3663C5202 C5201

X3603

R3609

R826

R880 R827 R821

R3608 R3611 R3612

Q3427

R882 R817

R877 R816 R814

IC806

C3677 C3616

C816

C3668C3667 R3621

R3601

C3601 C3608 R3617 R3618 C3607 R3625 C3619 C3627 C3626

C3602 C3453 R3620 C3671

R3487 C3444 C3462

R876 C819

D803

C808

C824 C823 C818 C835 C834 C839 C901 C833 C838 C900

R972 FB802 FB801 C904 IC807

C863

C820 C826

C3439 C3438

R3663

R3664

C817 C812

C3672

R849

C825 R847

R5213

C3682

R3669

C3673 C3674

C3615 C3662 C3448

C902

R3622

C860

R954

C3428 C3634 IC3602 C3635 D805

R851 C837 R850 C836 C840 C841

R854

C845 C842 C849 FL804

FL801

C853

IC5202 L5201 P5203 LUG3405C5210 C5209

R855 R893 C847

FL803

C3636

R853 C843 C848 FL802 C844

R952 C889 R867 Q809 Q810

R3647 R3623 R3626

R3681 R3670 R3671 R3665C3661 R3643 R3672 Q3602 R3638 R3636 R3634

C3639 C3680 C3640

C851

C855

C850 FL805

R8201

R941

FL806 FL807

R3628C3681

C3641 C3642

R3686 R3687 R3690 R3688 R961

R942

R920 R864 R8103R8101

IC3607

R3630

R3642

FL808

C3645

R3685 R3684

FB806

C879

C3659 C3660

SC8201

C912 R892 R951 C876 FL809

C3658

C3656 C3657

C3655

C3646

R3689

C872 C881 C882 C880

FL810

C883 FL811

R971

R896 R898

R917 R970

L8112 L8111 L8110 L8109

R3682

FB1301 C1321 D1303

IC3603 R1340 FB1302 P1301D1306 C1320 FB1304 C1332

C3679

P3601

R3683 C1330 C1322 C1318 D1304 L1305 C1324 C1317 C1327 C1325 FB1303 L1306 C1326R2020 R2009 R5284 D5204 Q2001

D807

R871 C885 FB804

R936

C890 C891C913

C914 C915

R1339

P801

IC3605 C3683 C3684R1343

R881 R959 C906 R865

R960

R976

C1331

R950 C4210

L8114 L8108 L8107

L1304 IC1301 L1303

C4225

C8128

C8122

C8127

R1344 R1306

C1302 R1303 R1341

C4207

FB4202

R8148

C8120 C8118

Q2802 C2856

L2803

C4208 C4206

FB4204 FB4201

C2855D2804 D2805

C2850

C2859R8505 L8402 D8406 R4208 C4213

C8125

C4211 C4219

FB4203

R4224

C8144

C8129

D8407C8437

C4223

C8407

C4215

C8114

Q2801 C2848 D2803 D2807

R8447

C8408

C8130

R8509

C8406

R8500

R4228 R4223 C4224 C4220

R8504

C8471Q8405

C8112 C8111 C8110

C8422

D8410

L2802

C8459 R8508

R8432

R1312 R1311 C1307 C1309 C1312 C1315 C1311 C1308 C1313 R1338

C8134 C8141 C8124 C8131

Q8403

C8461

IC8103

C8462 R8444

R8431 R8435C8470 R8434R8438 R8439

C8440

R8429 R8401 R8430 R8441R8442 C8412R8443C8423

C8420 R8412

C8464

C2852 C2849

C2858

R1310 D1302

Q1303

R8422 R8423

C8441

R8411 C8419

C8121 C8119 C8123

R1309 R1308 R1313

C8439

C1314

C1304

C8477

R8415 R8414

R8436

R8120 R8143 C8107R8142 C8105 C8106 C8108 C8104 R8106 R8147 R8130 R8108 R8145R8146 R8110 R8140 R8141 C8102 R8112 R8134 R8116 C8103 R8122 R8135 C8117 R8136 R8124 R8137 R8126 R8128 C8101

C1319 D1305R2080 R2079

C1329 R1342R2017

Q8401 C8410IC8405 L2801

FL8101

C8116

IC8402

C8478

R8421 C8402 R8451 R8495 C8466 R8492 R8494 R8493 R8403 C8401 R8496 R8455 R8497 C8467 R8449

R8425 R8404C8403 R8446 R8453 R8491

R2019 R2018 Q2020 R2056 R2039 R2043

IC2002

C8474

R8437 R8440 R8433 C8414 R8448 C8438 D8405 R8413 C8430 R8418 R8416 C8418 C8421 D8402 R8454 R8450

C8417R8408 R8410R8409 C8416 R8405 R8406 C8428 C8405 C8404 C8426 R8445 R8506R8424 C8411 R8426 R8427 R8428 C8458

R8115 R8121

IC8102

C8115

C8424

C8109

C8436

D2001 R2114

C8425

C8432 C8415

R2025

C8409R8419 R8417

R8420 C8469 C8473 Q8402 R8452

C8444

C8138 C8133

R2306 R2030

D8401 C8433 C2812

R8460C8468

IC8101

C8113

C8132 C8135

FB2804

C2811 R2834 C2808

C2001P2801

R2112 R2089 R2088

R8507R8456

Q8410

R8118

D8408

R8499

C8435

R8131

Q8408

D2802 D2806

R8490 R8489 R8488 R8487 R8481 FB8103 R8477

R2832 R2829 C2806 R2830 R2831

R2069 R2068R2113

D8404

C8434

IC2803

C2021

R2835

Q2002

R8461

R8462 R8466

R2115

C2809

C8431 IC2006 C2807

R8458

R8457

R8114 R8151

R8107 R8109 R8111 R8113 R8117 R8123 R8102 R8125 R8127 R8129

C8447

R2833

R2105 R2086 R2001 R2032 R2031 R2026 R2027

Q2803

L8104 L8103 L8106 L8105

Q2019 R2013 C2003R8104 R2107 R2071

R2881

R2047

Q2804

C8465

R2035

R2826 R2828

Q8450

L8401

P8101

C2015 C2018 C2019R2064

SC8202

C8205 C8204 R2058

IC8403

R2827

R2081 R2010 R2060 R2057 R2065

D8403

L8403C8203 Q2821 C2810

C8207 R8208 R8202 R8204R8206 R8203 R8205R8207 C8201

C8449

D8409

C8457

C8456

C8463

C8442

C8446

C8427

R2052

C8443 C8445

C8210

FB2817 FB2801 R2882

FB2803

Q2822

R2040

R2883

C8476

L8113

R8407

R8228C8217 R8230 IC8201 R8233 C8219 R8234 R8235 C8220 R8231R8232R8236 R8209R8225 R8229 R2346 R8227 C8213

C2802C8475

R8220

C8206 R8211 C8208 R8213R8210 C8223 C8222 IC8202

R8212 C8209 R8238 R8216 R8214 R8219C8211 R8221C8214

R8215R8217 C8212

IC8404

C8215

C8448 R8482 R8471

R8464

C8452

R8218

R8222

R8467 C8450 R8470 C8451 R8473 C8454 R8476 R8475 R8478 R8480

L8102 L8101

R8483R8472R8469

Q8414 Q8413

Q8412

C8216

C8453 Q8411

R8463 R8468

R8224 R8223 R8486 R8241 R8239 R8226 R8484 C8221 R8240

C8226

LUG3403

P2301

LC-32D30M-BK/WH/RD

I

H

G

F

E

D

C

B

A

MAIN Unit (Side-B)1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

73

LC-32D30M-BK/WH/RD

IC8227 C8218 C8331 C8224C8202 IC804 C8229

D8702 C809 C861R8701

C8228 C8137 C8139 C8140 FB8102 C8143 FB8104 FB8101 FB8105 C8142 C8136 C8330

C8703IC8701

C8732C8710

C8733 R8715 R8714R8713 R8705 D412 D411 R422 R423 R424 Q404

Q408

Q405

D404R446 R433

Q406

D422 R413

R450 R451 R448 R449 Q409

R429 R430 R432 R428

C8225

Q412

Q403

R832

C805

R464 C406 C407R420

R445

R412

R431

C408

R452

R453 C425 C424

R427 C409

R447

IC8703

R411

D419

D405 D423

R842

R973 R974

Q401

R8708IC802

D8703 C8731

R421Q402

Q407 IC403 R434

IC404 R454R468

Q410

IC406

C802

R5243

R466R470

R467

H

R469

R8150

C8460 C8455 R8485R8479C8126

Q1519

C1578 C1579 R1568 R1622 C1586 R1507 C1587

C827IC805

R1501

R957 D4202C4205 C4209

X802 R858 R862

C8705 C8712R919 R918

C2317 R2335 C2316 C2315

R895

C8713 C8714 C8715 C8702

Q1517

G

R2336 C2318 R2323 R2316 C2319

C4204 R4214 IC4202C4203

C893 C892 C895 C896

R843 R841

C8728

C1614 C1613 C1608 R1606 R1518 C1615 C1616 R1595FB1510 C1592 C1597 FB1509

R1506

C1517 C1545 C1546

C1551 C1543 C1544R1593

C1596 C1599

C832

C8709

R1565

R8474 R8465

C8707 C8706

C859

C868 R859

FL812

C8708

C2320 R2344 C2313

R1566 C1548 C1547 R1580 C1531 R1508R1503 C1532Q1501 C1583 C1582

R1515

R403

IC4203

R4213

R878

C8717 C829 R924 C828 R914 C813 C831 R934 C822 C821 C810 C815 C898 C830R956 R955

R1509R8726

C8716 C8718 C8719 IC1501

C1589 C1591

R4212

C8701R8738 R8729 C8721

R1505

C1501

R2315

R2319 R2307

FB8106C4214 C4216 C4212

C8720

R1511

R1513

R1516 R1504 R1517

C8722

R2343 R2345 C2312 IC2302R2308 R2304 C2311 D8101 R4203 R4227 R4205 R4207 R4204 R4225 R4226 R4206 IC4201

R873R943 R944

IC801

R436 R414 IC402

R2309

R8149R8138

F

Q8101 R8139

C8413 R8459C8429

R875 R904

R969 R968

R852

C401

FB402 D413 C404 R419 R426 R418IC405

D406

C405

R940

R8144 R8402C8472

R435 C410

C4222 C4221

C4218 C4217 R4222

R4221

R4218

R4202 R4201R953

R828C4201

R885 R886 R900 C894C886 C887 R939 C903

R866

X4201

R869R967 R889 R975 R945 R937 R938 R890 R962 R946 R947 R949 R948 R872

R863

R901 R902

C4202

R861

R860

X803 R870

C884

C3475 R3543 C3477

Q3414 C3479 R3558 R3552 R3551

C888

L3404

ER8512

C8479 R8510

R8511 R3436 C3464 C3431 C3430 C3450 R3567 R3566 Q8415 R8513 IC2804 C2814

R3557 C3482

R3561R3545 R3534 R3548 R3549 R3553

Q3415

C3470 R3460 C3449 C3458 C3446 C3445

R8516 R8515 R8514

D8411

R2817 R2818

R2809C2805

R2873 R2805Q2819 C2829

DR2029 R2037 C2014

R3564 C3433 C3434 C3429 R3661 C3437 C3440 C3441 C3442 C3443C3452 C3451

Q3412

R3547

R3530

R3445

D3424

C3499 R3443

R3496R3404 Q3417

R3556

R3565

R3597

C2831 R2807 R2813 C2815 FB2810 R2814 R2815 C2837

R3419

R2816

C3465 C3468 C3456 C3459 R3440C3461

IC3409

R3662

C2804

R2821 C2843 R2819

IC2801

IC2802

C3457 C3498 C3497

C3460

R2878

Q2820

R2872 R2803 R2802 R2812 C2836 FB2809 R2810 C2841 C2846

C2827 R2804 C2830 R2806

R2082

R2036 R2109 R2108

R2044 R2110FL2001

R2111

Q1302C1316 C1310

C3629 C3628 C3610 C3609

R3605 C3605 R3604 C3686D3604

C1301 R1302

C3643

C3637

C3630

C3613

C1306 R1305

C3647C3654

C

C2840 C2838 R2847 C2833 C2844 IC2805 R2846 C2801 C2813 C2832 FB2802D2801 R2879 C2022

IC2001 R2024 R2014 R2033 R2055 R2050 R2012 R2016

R2049 R2051 R2034 C2020R2074

Q1301C1305 R1307 R1301

R3668 R3652 R3640 R3657 R3645

C3480 C3472 C3471R3675

C3649

R1336

R2045

R3632 C3650 R3653 C3652 R3641R3667

C3624 C3611 C3612 C3620 C3622

C3617 C3618

IC3606 C3685 R3674

R1335

R3596R8624

R3560

Q2021

C1323

R2091 R2092 R2093

D1301R1328 R1337 C1328 D1309

D1307D1308

C3632

Q8603R8623 C8606

R2041R8618 R8620 R8621

IC2009

R2073

R2072

R2347

R8625R8622

Q8602

Q8601R2095

Q2025

R2061 R2021 R2063 R2015 R2083 R2059 R2066

R2077

Q1304 D5209R5226

R5286D5202

R8614 R8619 R8617 R8612 C8602 C8603R8607

R1334 R1326 R1333 R1320 R1325 R1319 R1322 R1321 R1317

TH801

R2099

R5285

D3605

R3680

D3601

B

R3678 Q3606

D3425

A

MAIN Unit (Side-B Chip)1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

74

LC-32D30M-BK/WH/RD

[2] KEY UnitKEY Unit (Side-A)D

C

KEY Unit (Side-A Chip)BR154R153 S155 S154 S152 S151 S153 D152 R151 D151 S156 S157

D155 P151

R152

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

[3] R/C, LED Unit

D

R/C, LED Unit (Side-A)

C

B3

R/C, LED Unit (Side-A Chip)R140 C103 C111

C104 C107 SLD101 RMC101 R101 C102 IC101C105

R107 R104 R109

Q102 D114Q103

R126 R121Q105

C108 D115R127 R122

R120 R119 RMC102D116

R108

Q106

R135 R136

D103 R105 R102R117 R137

R124 Q107

P101

P102

C110

R103

R139

IC102 R118 R116

R132

D101

Q104

R106 R138

R123

R110

C101

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

75

LC-32D30M-BK/WH/RD

[4] MINI AV Unit

I

H

MINI AV Unit (Side-A)G

F

E

MINI AV Unit (Side-A Chip)D

C

B

MINI AV Unit (Side-B)A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

76

LC-32D30M-BK/WH/RD

CHAPTER 8. SCHEMATIC DIAGRAMLC-32D30M-BK/WH/RD

Service Manual

[1] DESCRIPTION OF SCHEMATIC DIAGRAM1. VOLTAGE MEASUREMENT CONDITION:1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.

2. INDICATION OF RESISTOR & CAPACITOR:RESISTOR 1) The unit of resistance "" is omitted. (K=k=1000, M=M). 2) All resistors are 5%, unless otherwise noted. (K= 10%, F= 1%, D= 0.5%) 3) All resistors are 1/16W, unless otherwise noted. CAPACITOR 1) All capacitors are F, unless otherwise noted. (P=pF=F). 2) All capacitors are 50V, unless otherwise noted. CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. SAFETY NOTES: 1) DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. IMPORTANT SAFETY NOTICE: PARTS MARKED WITH " "( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.

81

LC-32D30M-BK/WH/RD

[2] KEY Unit

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

82

LC-32D30M-BK/WH/RD

[3] MAIN Unit MAIN Unit-1/17 (*On this model, the Main Circuit Basic Diagram 9/17 is not applied.)

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

83

LC-32D30M-BK/WH/RD MAIN Unit-2/17

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

84


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

85


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

86


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

87


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

88


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

89


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 10


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 11


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 12


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 13


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 14


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 15


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 16


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 17


I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 18

LC-32D30M-BK/WH/RD

[4] R/C, LED Unit

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 19

LC-32D30M-BK/WH/RD

[5] MINI AV Unit

I

H

G

F

E

D

C

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

8 20

PartsGuide

LC-32D30M-BK/WH/RD

PARTS GUIDENo. S48I5LC32D30M

Note: The reference numbers on the PWB are arranged in alphabetical order.

MODELSCONTENTS

LC-32D30M-BK LC-32D30M-WH LC-32D30M-RDCABINET AND MECHANICAL PARTS LCD PANEL UNIT SUPPLIED ACCESSORIES PACKING PARTS (NOT REPLACEMENT ITEM)

[1] [2] [3] [4] [5] [6]

PRINTED WIRING BOARD ASSEMBLIES LCD PANEL DUNTKE266FM03 (KEY Unit) DUNTKE508FM11 (MAIN Unit) DUNTKE568FM02 (R/C, LED Unit) DUNTKE708FM02 (MINI AV Unit)

[7] [8] [9] [10]

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.This document has been published to be used for after sales service only. The contents are subject to change without notice.

LC-32D30M-BK/WH/RDNO. PARTS CODE PRICE NEW RANK MARKPART DELIVERY

DESCRIPTION

[1] PRINTED WIRING BOARD ASSEMBLIESN N N N N N D151 D152 D155 P151 R151 R152 R153 R154 S151 S152 S153 S154 S155 S156 S157 C401 C402 C403 C404 C405 C408 C409 C410 C424 C425 C801 C802 C803 C805 C806 C808 C809 C810 C811 C812 C813 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C839 C840 C841 C842 C843 C844 C845 C847 C848 C849 C850 C851 C853 DUNTKE266FM03 DUNTKE508FM11 DUNTKE568FM02 DUNTKE708FM02 RUNTKA419WJQZ AG CB AS AR BU N N N V V V V V KEY Unit MAIN Unit R/C, LED Unit MINI AV Unit INVERTER/POWER Unit

[2] LCD PANELR1LK315T3GW30W DA J 32"LCD Panel Module Unit

[3] DUNTKE266FM03 (KEY Unit)RH-EX0646GEZZY RH-EX0646GEZZY RH-EX0646GEZZY QPLGNA059WJZZ VRD-RA2BE822JY VRD-RA2BE123JY VRD-RA2BE822JY VRD-RA2BE123JY QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ AA AA AA AC AA AA AA AA AB AB AB AB AB AB AB J J J J J J J J J J J J J J J Zener Diode, MTZJT-7215B Zener Diode, MTZJT-7215B Zener Diode, MTZJT-7215B Plug, 5pin (KM) Resistor, 8.2k 1/8W Carbon Resistor, 12k 1/8W Carbon Resistor, 8.2k 1/8W Carbon Resistor, 12k 1/8W Carbon Switch, CH-UP Switch, CH-DOWN Switch, INPUT Switch, VOL-UP Switch, VOL-DOWN Switch, MENU Switch, POWER

[4] DUNTKE508FM11 (MAIN Unit)RC-KZA510WJPZY VCKYCZ1EB103KY VCCCCZ1HH330JY VCCCCZ1HH330JY VCKYCZ1EF104ZY RC-KZA510WJPZY VCKYCZ1EB103KY VCKYCZ1EF104ZY RC-KZA510WJPZY VCKYCZ1EB103KY RC-KZA510WJPZY RC-KZA069WJZZY RC-KZA510WJPZY RC-KZA069WJZZY RC-KZA510WJPZY VCKYCY1AB105KY RC-KZA069WJZZY VCKYCY1HB104KY RC-KZA510WJPZY RC-KZA510WJPZY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCZ1EF104ZY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCZ1HB102KY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCZ1AB104KY VCKYCZ1HB102KY RC-KZA069WJZZY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1HB104KY RC-KZA069WJZZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1HB102KY RC-KZA510WJPZY VCKYCZ1EF104ZY AB AA AB AB AA AB AA AA AB AA AB AB AB AB AB AB AB AA AB AB AA AA AA AA AA AA AB AA AA AA AA AB AB AB AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Capacitor, 10 16V Ceramic Capacitor, 0.01 25V Ceramic Capacitor, 33p 50V Ceramic Capacitor, 33p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.01 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.01 25V Ceramic Capacitor, 10 16V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 10 16V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 10 16V Ceramic Capacitor, 1 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 10 16V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 10V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 0.1 50V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 25V Ceramic

2

LC-32D30M-BK/WH/RDNO. PARTS CODE PRICE NEW RANK MARKPART DELIVERY

DESCRIPTION

[4] DUNTKE508FM11 (MAIN Unit)C855 C859 C860 C861 C863 C868 C872 C876 C879 C880 C881 C882 C883 C884 C885 C886 C887 C888 C889 C890 C891 C892 C893 C894 C895 C896 C899 C900 C901 C902 C903 C904 C906 C912 C913 C920 C1306 C1307 C1308 C1309 C1310 C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1319 C1320 C1321 C1322 C1323 C1324 C1326 C1328 C1332 C1501 C1502 C1503 C1504 C1505 C1517 C1531 C1532 C1543 C1544 C1545 C1546 C1547 C1548 C1551 C1578 C1579 C1582 C1583 C1586 C1587 C1589 C1591 C1592 C1596 C1597 C1599 RC-KZA510WJPZY VCCCCZ1HH150JY VCKYCZ1EF104ZY RC-KZA069WJZZY RC-KZA069WJZZY VCCCCZ1HH150JY VCKYCZ1EF104ZY VCKYCZ1EF104ZY RC-KZA510WJPZY RC-KZA510WJPZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCCCCY1HH9R0DY VCKYCY1HB103KY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCCCCY1HH9R0DY VCKYCZ1EF104ZY VCKYCZ1EF104ZY RC-KZA510WJPZY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1HB102KY VCKYCZ1CB103KY VCKYCZ1HB102KY RC-KZA069WJZZY RC-KZA069WJZZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1EF104ZY RC-KZA069WJZZY VCEASX0JN476MY VCKYCY1AB105KY VCCCCY1HH390JY RC-KZA510WJPZY VCKYCY1AB105KY VCKYCY1AB105KY VCKYCY1HB102KY VCKYCY1HB102KY VCKYCY1EF104ZY VCKYCY1AB105KY VCKYCY1AB105KY VCKYCY1AB105KY VCEASX1VN227MY VCKYCY1EF104ZY RC-KZA114WJZZY RC-KZA114WJZZY VCKYCY1HB103KY VCKYCY1HB103KY VCKYCY1HB103KY VCKYCY1HB103KY RC-KZA619WJZZY RC-KZA114WJZZY RC-KZA114WJZZY RC-KZA619WJZZY VCKYCY1HB102KY VCCCCY1HH101JY VCKYCZ1AB104KY RC-KZA069WJZZY RC-KZA069WJZZY RC-KZA069WJZZY RC-KZA069WJZZY RC-KZA510WJPZY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY RC-KZA510WJPZY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1EF104ZY VCKYCZ1EF104ZY VCKYCZ1HB102KY VCKYCZ1HB102KY AB AB AA AB AB AB AA AA AB AB AA AA AA AA AA AA AA AA AA AA AB AA AB AB AB AB AB AB AA AA AA AB AC AB AA AB AB AB AA AA AA AB AB AB AE AA AB AB AA AA AA AA AB AB AB AB AA AA AB AB AB AB AB AB AA AB AA AB AA AB AA AB AB AA AB AA AB AA AB AA AB AA AA AB AB J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Capacitor, 10 16V Ceramic Capacitor, 15p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 15p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 10 16V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 9p 50V Ceramic Capacitor, 0.01 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 9p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.01 16V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 47 6.3V Electrolytic Capacitor, 1 10V Ceramic Capacitor, 39p 50V Ceramic Capacitor, 10 16V Ceramic Capacitor, 1 10V Ceramic Capacitor, 1 10V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1 10V Ceramic Capacitor, 1 10V Ceramic Capacitor, 1 10V Ceramic Capacitor, 220 35V Electrolytic Capacitor, 0.1 25V Ceramic Capacitor, 1 25V Ceramic Capacitor, 1 25V Ceramic Capacitor, 0.01 50V Ceramic Capacitor, 0.01 50V Ceramic Capacitor, 0.01 50V Ceramic Capacitor, 0.01 50V Ceramic Capacitor, 0.47 50V Ceramic Capacitor, 1 25V Ceramic Capacitor, 1 25V Ceramic Capacitor, 0.47 50V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 100p 50V Ceramic Capacitor, 0.1 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 4.7 10V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 10 16V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capacitor, 1000p 50V Ceramic Capacitor, 0.1 25V Ceramic Capaci

lc-32d30m

Documents

syncj2pin

upper left

rank markpart

prior written

leader lt448

sp duct ass

qualified

front sp duct