land cruiser 80 (rhd)

TOYOTA MOTOR CORPORATIONManual Ref. Nr. T3RL5-0-500

LAND CRUISER 80 (RHD)

VEHICLE SECURITY SYSTEMTVSS IIIB

INSTALLATION INSTRUCTIONS

PART NUMBER

MAIN KIT 08585-00880

SUB KIT (SIREN AND RADAR) 08586-50820

FITTING KIT 08586-60950

FOR FZJ80R, HDJ80R, HZJ80R

TOYOTA MOTOR CORPORATIONManual Ref. Nr. T3RJ8-0-500

PRECAUTIONS

Land Cruiser 80 (RHD) - 2

Land Cruiser 80 TOYOTA TVSS IIIB

Precautions

PLEASE READ THOROUGHLY THESE PRECAUTIONSFOR THIS SYSTEM INSTALLATION

• Be sure to disconnect the negative (-) lead from the battery ter-minals.

• Do not pinch the rear wiring or harness in the tightened part.

• When passing the wires through the bulkhead or other panels,use a grommet to ensure waterproofing.

• Protect the wiring with tape when it is passed through a hole.

• When disconnecting the connectors, be sure to grip the con-nector body. Do not tug on the wiring.

• Do not forcibly pull any car wiring harness. Rough tugging mayresult in opened connections, or a broken wire or harness.

• Confirm that lamps, horn, wiper and other car accessories operatenormally.

• Protect your car with wing covers, seat and so on.

• Use the correct tool when tightening bolts or nuts.

• Before drilling a hole, check that the rear of the mounting wallis clear.

• Be sure to firmly tighten connectors and terminals.

• Before connecting the power wiring to the battery, check thewiring connections, harness, etc. to see that they are properlysecured.

• Check body and trim near area of installation to be certain nodirt or scratches resulted from the installation.

waterproof - O.K. !!

Taping

Grommet

Insertcompletely

Stop it !

TABLE OF CONTENTS



Tab

le o

f C

onte

nts

Precautions ................................................................................................................................................................... 2

System Components• Main Kit ............................................................................................................................................................... 4• Sub Kit (Siren and Radar) ................................................................................................................................... 4• Fitting Kit ............................................................................................................................................................. 5

System Layout and Wire Harness Outline• Main .................................................................................................................................................................... 7• Engine ................................................................................................................................................................. 8

Connector Arrangement of the TVSS Fitting Kit (Pin View) ............................................................................ 9

TVSS Installation Procedures• Vehicle Disassembly (Passenger Compartment) ................................................................................................ 10• Wire Harness (Main) Installation ........................................................................................................................ 13• Mounting the Status Monitor .............................................................................................................................. 15• Mounting the Radar Sensor ................................................................................................................................ 16• Mounting the Glass Breakage Control Unit ......................................................................................................... 18• Vehicle Disassembly (Engine Compartment) ...................................................................................................... 20• Mounting the Siren ............................................................................................................................................. 23• Wire Harness (Engine) Installation ...................................................................................................................... 25• Mounting the Hood Switch ................................................................................................................................. 28 • Setting the TVSS ECU Dip Switches and Testing the System ............................................................................. 29• Mounting the TVSS ECU ..................................................................................................................................... 30• Mounting the Glass Breakage Sensor ................................................................................................................. 32• Attaching the Stickers ......................................................................................................................................... 34

SUB KIT (SIREN AND RADAR) 08586-50820

MAIN KIT 08585-00880

Land Cruiser (RHD) - 4


Main Kit - Sub Kit (Siren and Radar)

No. Description Qty

TVSS ECU 1

REMOTE CONTROL TRANSMITTER 2II

I

No. Description Qty

SIREN 1

SIREN BRACKET 1

BOLT 2

NUT 2

RADAR SENSOR 1

CAP 2IV

III

iv

iii

ii

i

I

i

II

ii iii iv

III IV

Other parts in the kit are not used.

FITTING KIT 08586-60950



Fitt

ing

Kit

No. Description Qty

WINDOW STICKER 2

WIRE HARNESS (MAIN) 1

PROTECTIVE BRACKET 1

SCREW 1

BLIND RIVET 1

BUTYL TAPE 1

WIRE TIE (SMALL) 10

WIRE TIE (LARGE) 4

FOAM (1 DIVISION ON 1 SHEET) 1

FOAM (2 DIVISIONS ON 1 SHEET) 2

STATUS MONITOR 1

GLASS BREAKAGE CONTROL UNIT 1

GLASS BREAKAGE SENSOR 1

WIRE HARNESS (ENGINE) 1

HOOD SWITCH 1

HOOD SWITCH BRACKET 1

MOUNTING BRACKET (FOR SIREN) 1

BOLT (M6 X 18MM) (FOR SIREN) 1

BOLT (M6 X 30MM) (FOR SIREN) 2

BOLT (M8 X 20MM) (FOR HOOD SWITCH) 1

NUT (M6) 3

WASHER 222

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

2 4 5

6

7

8

Fitting Kit



31

910

11

12 13 14 15

16 17 18 19

20 21 22

SYSTEM LAYOUT AND WIRE HARNESS OUTLINE (MAIN)



Sys

tem

Lay

out

and

Wire

Har

ness

Out

line

(Mai

n)

Pos. No. Description

TVSS ECU

TVSS ECU CONNECTOR (26P GREY)

GROUND TERMINAL

PRE-WIRE CONNECTOR (12P WHITE)

STATUS MONITOR CONNECTOR (2P CLEAR)

RADAR SENSOR CONNECTOR (4P WHITE)

GLASS BREAKAGE CONTROL CONNECTOR (6P WHITE)

GLASS BREAKAGE SENSOR CONNECTOR (2P WHITE)

GLASS BREAKAGE CONTROL UNIT

RADAR SENSORK

J

H

G

F

E

D

C

B

A

A

B

C

E

D

G

H

J

K

F



System

Layout and Wire H

arness Outline (E

ngine)

SYSTEM LAYOUT AND WIRE HARNESS OUTLINE (ENGINE)

Pos. No. Description

PRE-WIRE CONNECTOR (6P GREY MALE)

SIREN CONNECTORS (6P GREY FEMALE)

GROUND TERMINAL

HOOD SWITCH CONNECTOR (2P WHITE)

SIRENe

d

c

b

a

a

d

b

c

e


B

E

D

F

a b

(female pin)

CONNECTOR ARRANGEMENT OF THE TVSS FITTING KIT (PIN VIEW)


Con

nect

or A

rran

gem

ent

of t

he T

VS

S F

ittin

g K

it (P

in V

iew

)

(male pin) (female pin)

(female pin)

(female pin)

(male pin)

d

(female pin)

G H

(female pin) (male pin)

Figure 1

Figure 2

Figure 3

VEHICLE DISASSEMBLY (PASSENGER COMPARTMENT)


2)

Peel back the carpet .3

3) a) Remove the gear and the transfer

shift knobs.

b) Remove the console panel .

: Screws (3x): Screw (1x)8

7

6

54


Vehicle D

isassembly (P

assenger Com

partment)

1)

Remove the passenger’s side front sidestep cover .

Plastic nut2

1

1 2

3

FOR MANUAL TRANSMISSION MODELS

7

7

7

8

45 6

Figure 4

Figure 5


4)

a) Remove the transfer shift knob .

b) Remove the console panel .

: Screws (3x): Screw (1x)8

7

9

5

5)

Remove the console compartment .

: Bolts (3x)11

10

6)

a) Remove the accessory compartment and the ashtray .

b) Remove the screws (4x) securingthe centre cluster .

c) Remove the switch hole cover .

: Locks (4x)14

15

16

7

13

12

Veh

icle

Dis

asse

mbl

y (P

asse

nger

Com

part

men

t)


Figure 6

FOR AUTOMATIC TRANSMISSION MODELS

15

16

7

7

7

7

7

10

9

8

11 1111

12

13

5

14


7)

Pull out the centre cluster .(Do not disconnect any connector).

16

Vehicle D

isassembly (P

assenger Com

partment)


Figure 7

16

Figure 8


Wire

Har

ness

(M

ain)

Ins

talla

tion


WIRE HARNESS (MAIN) INSTALLATION

1)

a) Locate and pull out the 12P connector(white) in the kick panel area on the

passenger’s side.

b) Connect the fitting kit wire harness(main) 12P connector (white) tothe 12P connector white.17

D2

17

Figure 9

2)

a) Locate and remove the bolt in the kickpanel area.

b) Secure the ground terminal of the fit-ting kit wire harness (main) with thebolt .

c) Lay the fitting kit wire harness (main) under the rubber trim .19

2

18

2

C

18

Figure 10

3)

Lay the fitting kit wire harness (main) under the carpet .3

2

18

19

17

E

C

D

22

2

2

3

Figure 11


4)

Lay the fitting kit wire harness (main) under the carpet .3

2

Wire H

arness (Main) Installation


5)

Connect the fitting kit wire harness (main)26P connector (grey) to the TVSS

ECU .I

B2

Figure 12

B

BG

F

2

I

3



Mou

ntin

g th

e S

tatu

s M

onito

r

MOUNTING THE STATUS MONITOR

Figure 13

1)

a) Put the fitting kit wire harness (main) 2P connector through the switch hole

from the rear of the centre cluster .

b) Reinstall the centre cluster .

c) Connect the fitting kit wire harness(main) 2P connector (clear) to thestatus monitor’s 2P connector (clear).

d) Fit the status monitor to the switchhole .20

11

11

E2

16

1620

E

220

16F

L2

11


Mounting the R

adar Sensor


MOUNTING THE RADAR SENSOR

2)

Remove the bracket .

: Screws (2x)VIII

VII

3)

Fit the caps (2x) to the radar sensor .IIIIV

1)

a) Remove the cap from the radar sen-sor .

b) Locate the trimmer in the small hole.

c) Turn the trimmer clockwise to themaximum.

d) Turn the trimmer counterclockwisebetween the first and the second posi-tion from the maximum.

e) Test and adjust the sensor sensitivity inaccordance with the SETTING GUIDE.

f) Refit the cap .V

VI

VI

VI

III

V

Figure 16

Figure 15

Figure 14

2

1

MAX.

V

IIIVI

VII

VIIIIII

III

IV

IV

VIII



Mou

ntin

g th

e R

adar

Sen

sor

4)

Attach the butyl tape to the back of theradar sensor .III

6

Figure 17

5)

a) Connect the fitting kit wire harness(main) 4P connector (white) to theradar sensor 4P connector (white).

b) Locate and mark the radar location(shaded portion in the figure).

M

F2

Figure 18

6)

Position the radar sensor as shown andpush to attach.

III

Figure 19

M

F

2

2

6

III

III

III


Mounting the G

lass Breakage C

ontrol Unit


MOUNTING THE GLASS BREAKAGE CONTROL UNIT

2)

Turn the sensor adjustment screw to posi-tion “9” to obtain optimum sensitivity.

NOTE: False alarm may occur if thesensitivity is set too high. Testthe system according to theSETTING GUIDE to ensure thecorrect setting.

3)

a) Run the wire ties (2x) through theslits , , and .

b) Connect the fitting kit wire harness(main) 6P connector (white) to theglass breakage control unit .12

G2

4321

8

1)

Measure and cut the carpet as shown tomake four slits , , and .4321

Figure 22

Figure 21

Figure 20

60 mm

45 mm10 mm3,5 mm10 mm

10 mm

1

34

2

1

3

4

2

G

8 12

12



Mou

ntin

g th

e G

lass

Bre

akag

e C

ontr

ol U

nit

4)

Put the wire ties (2x) around the glassbreakage control unit and secure.12

8

Figure 23

2

12

8


Vehicle Disassembly (Engine Com

partment)


VEHICLE DISASSEMBLY (ENGINE COMPARTMENT)

2)

Remove the passenger’s side indicator light.

: Screw23

22

3)

Remove the battery .

: Nuts (6x): Frame: Hook brackets (2x): Negative battery terminal: Positive battery terminal29

28

27

26

25

24

1)

Remove the bolt .21

Figure 26

Figure 25

Figure 24

FOR PETROL ENGINE MODELS28 25 24 25

26

27

25

29

23

22

21


Vehi

cle

Disa

ssem

bly

(Eng

ine

Com

partm

ent)


4)

Remove the ground bolt .(Do not discard)

30

Figure 27

5)

Remove and discard the two bolts secu-ring the fuse box .32

31

Figure 28

6)

Remove the battery cover .

: Nuts (2x): Washers (2x): Bracket35

34

25

33

Figure 29

FOR PETROL ENGINE MODELS


FOR DIESEL ENGINE MODELS

32

31

33 3425

35

2534

30


Vehicle Disassembly (Engine Com

partment)


7)

Remove the battery .

: Nuts (4x): Frame: Hook brackets (2x): Negative battery terminal: Positive battery terminal29

2827

26

25

24

Figure 30

8)

Remove the battery tray and the groundbolt .

: Bolts (5x): Clip: Foam39

38

37

3036

Figure 31

9)

a) Lift the fuse box .

: Bolts: Clip

b) Release the washer tank .

: Bolts (3x) (Discard two of them)44

43

42

41

40

Figure 32




36

37

4443

41

40

42

44

38

39

25

2525 24

26

30

27

28

29


Mou

ntin

g th

e Si

ren


MOUNTING THE SIREN

2)

a) Relocate the fuse box with the bolts(2x) and the washers (2x).

b) Locate the siren bracket to the tip of thebolts .

c) Secure the siren to the vehicle with thenuts (2x).21

19

2219

32

3)

a) Push the siren towards the sirenbracket .

b) Make sure to tighten the nuts (2x).iv

ii

i

1)

a) Fit the mounting bracket to the sirenbracket with bolt and nut .

b) Fit the siren bracket to the siren with the bolts (2x) and nuts (2x)temporarily.

iviii

iii

2118ii

17

Figure 35

Figure 34

Figure 33


FOR PETROL ENGINE MODELS3222

19

22 21

21

17

18

21

i

iv

iv

i

iiiv

iiii

iv


Mounting the Siren


4)

a) Relocate the washer tank with thebolts (2x), the washers (2x) andbolt .

b) Locate the siren bracket to the tip of thebolts .

c) Secure the siren to the vehicle with thenuts (2x).21

19

44

2219

43

Figure 36

5)

a) Push the siren towards the sirenbracket.

b) Make sure to tighten the nuts (2x).iv

i

Figure 37



43 44

19

22

22

21

21

iv

i

iv

i


Wire

Har

ness

(E

ngin

e) I

nsta

llatio

n


WIRE HARNESS (ENGINE) INSTALLATION

2)

Connect the fitting kit wire harness (engine)6P male connector (grey) to the

vehicle 6P female connector (grey).45

a14

3) Lay and attach the fitting kit wire harness(engine) with the wire ties (2x).714

Figure 39

1)

a) Locate the 6P connector (grey) in thebrake booster area.

b) Remove and discard the cap fromthe 6P connector .45

46

45

Figure 38

Figure 40

45

45

46

a

7

147

14

4)

Lay and attach the fitting kit wire harness(engine) with the wire ties (3x).714

Figure 41

6)

a) Connect the fitting kit wire harness (en-gine) 6P female connector (grey)to the siren 6P male connector (grey).

b) Secure the fitting kit wire harness(engine) ground terminal with theexisting bolt .

c) Attach the fitting kit wire harness (engi-ne) with the wire tie .714

30

c14

f

b14

Figure 43

5)

Lay and attach the fitting kit wire harness(engine) with the wire ties (2x).714

Figure 42



Wire H

arness (Engine) Installation


30c

f

b

14

14

7

7

14

7 14 7


Wire

Har

ness

(E

ngin

e) I

nsta

llatio

n


7)

a) Connect the fitting kit wire harness(engine) 6P female connector (grey) to the siren 6P male connector (gey).

b) Secure the fitting kit wire harness(engine) ground terminal with theexisting bolt .30

c14

f

b14

Figure 44

8)

Secure the fitting kit wire harness (engine)with the wire tie .714

Figure 45



30 c

b

f

14

7

14

MOUNTING THE HOOD SWITCH


2)

Fit the hood switch to the hood switchbracket .16

15

3)

Connect the fitting kit wire harness (engine)2P connector (white) to the hood

switch .15

d14


Mounting the H

ood Sw

itch

1)

Fit the hood switch bracket to the vehi-cle with the bolt .20

16

Figure 46

Figure 47

Figure 48

d

15

14

15

16

1620


Set

ting

the

TV

SS

EC

U D

ip S

witc

hes

and

Tes

ting

the

Sys

tem


SETTING THE TVSS ECU DIP SWITCHES AND TESTING THE SYSTEM

1)

a) Set the dip switches of the TVSS ECUas shown.

b) Test the system as explained in theSETTING GUIDE.

I

Figure 49

ONOFF

1 2 3 4 5 6 7 8

I



Mounting the T

VS

S E

CU

MOUNTING THE TVSS ECU

2) a) Fit the nose adapter fitting to the

nose of the riveting tool .

b) Open the riveting tool and put theblind rivet on the nose.

c) Insert the tip of the blind rivet throughthe hole of the TVSS ECU as far asit will go.

d) Close the riveting tool arms repeat-edly until the blind rivet comes away.5

48

I

5

5

48

4847

3)

a) Attach the foam to the TVSS ECU .

b) Run the wire ties (2x) through theholes of the TVSS ECU .I

8

I10

1)

a) Wrap the fitting kit wire harness along the 26P connector (grey) in thefoam .

b) Fit the protective bracket to theTVSS ECU with the screw andthe blind rivet .

(For details of how to use the blind rivet seenext figure).

5

4I

3

10

B

2

Figure 50

Figure 51

Figure 52

NOTE: Any other blind riveting tool willdo.

a

c d

b

47

4848

48

810

5

3

2

5

4 10

I

I



Mou

ntin

g th

e T

VS

S E

CU

4)

a) Put the wire ties (2x) around the rearheater duct .

b) Put the TVSS ECU on to the rearheater duct .57

I

57

8

5)

Secure the TVSS ECU to the rear heaterduct with the wire ties (2x).857

I

Figure 53

Figure 54

57

57

H

8

8

8

8

I

I

MOUNTING THE GLASS BREAKAGE SENSOR


2)

Route the fitting kit wire harness (main) 2P connector (white) in the consolecompartment and through the hole from the inside.

6210

G

2

3)

Refit the accessory tray to the consolecompartment .10

58


Mounting the Glass Breakage Sensor

1)

Remove the accessory tray and bracketfrom the console compartment .

: Screw: Screw (3x)61

60

105958

Figure 55

Figure 56

Figure 57

10

10

10

58

61

62

61

59

5860

G

G

2


4)

Attach the glass breakage sensor to theconsole compartment so that the sensor is located under the accessory tray andpoints to an angle of 45 degrees from topas shown.

58

13

13

5)

a) Attach the fitting kit wire harness (main)2P connector (white) to the glass

breakage sensor 2P connector (white).

b) Cut the foam in half and wrap the2P connectors in one half.

c) Put the 2P connectors into the acces-sory tray.

9

N

G2

6)

Attach the 2P connectors to the accessorytray by the other half of the foam asshown.

9

Mou

ntin

g th

e Gl

ass

Brea

kage

Sen

sor


Figure 58

Figure 59

Figure 60

45°

58

G

N

9

9

13

ATTACHING THE STICKERS

1)

Attach the stickers to both front doorwindows.

1

Figure 62


7)

Refit the console compartment and bun-dle up the excessive part of the fitting kitwire harness (main) into it.2

10

Mounting the Glass Breakage Sensor / Attaching the Stickers


Figure 61

90 mm

30 mm

REFIT THE TRIM AND REMOVED PARTS

10

1

2

GENUINE PARTS

land cruiser 80 (rhd)

Documents